Steam Pro Non-Stop - Pdfstream.manualsonline.com
Contents
1. desired steam output for each garment from O to 60 grams per minute Using your professional ironing system Before first use Remove any adhesive stickers plastic covers or cardboard sleeves from the soleplate Remove any remaining adhesive by rubbing the soleplate with a cloth dampened with methylated spirits Filling the tank with water Before filling the tank with water ensure that the power is turned off and the plug is removed from the power outlet The tank can be filled with water while the iron is hot Lift the water tank cover Using a jug with a pouring spout slowly pour water into the inlet Close the cover Note The non corrosive stainless steel boiler has been designed to allow you to use tap water in your professional ironing system However in very hard water areas Sunbeam recommends the use of distilled or demineralised water For best performance we recommend the use of Sunbeam Water Demineraliser available from Sunbeam Service Centres and selected retail outlets This produces up to 30 litres of demineralised water to prolong the life of your iron Caution Do not fill the water tank with fabric conditioners starches scented water or any other solution as these will damage the steam mechanism Do not use contaminated water Using your professional ironing system 1 Insert the plug into a 230 240V power outlet and turn the power on 2 Place both the boiler and the iron switches in the on2. on or near a hot gas flame electric element or on a heated oven Do not place on top of any other appliance Do not let the power cord of an appliance hang over the edge of a table or bench top or touch any hot surface For safety reasons and to avoid maintenance by unskilled persons some appliances are sealed using tamperproof screws Such appliances should always be returned to the nearest Sunbeam Appointed Service Centre for adjustment or repair if required Do not operate any electrical appliance with a damaged cord or after the appliance has been dropped or damaged in any manner If damage is suspected return the appliance to the nearest Sunbeam Appointed Service Centre for examination repair or adjustment For additional protection Sunbeam recommend the use of a residual current device RCD with a tripping current not exceeding 30mA in the electrical circuit supplying power to your appliances Do not immerse the appliance in water or any other liquid unless recommended If you have any concerns regarding the performance and use of your appliance please visit www sunbeam com au or contact the Sunbeam Consumer Service Line Ensure the above safety precautions are understood Thermostat light The thermostat light illuminates to indicate that the iron soleplate is heating and goes out when it has reached the temperature selected on the temperature dial The thermostat light cycles on and off during ironing as
3. temperature Always read garment labels and follow the manufacturer s ironing instructions Refer to the Ironing Chart for temperature recommendations Hints for easier ironing Sort articles to be ironed according to the type of fabric This will reduce the need to adjust the temperature to suit varying garments Start with garments requiring lower temperatures and work your way through to items requiring higher temperatures If you are unsure of the fabric content of a garment test a small area such as a seam or inside hem section before ironing a visible area Start with a low temperature and gradually increase the heat to find the best setting for ironing the garment When reducing the temperature to iron sensitive fabrics allow approximately 2 minutes for the iron to cool to the new setting Pure woollen fabrics 100 wool can be steam ironed with the temperature dial set to Wool Use an ironing cloth to prevent shine marks on the fabric Fabrics such as velour wool linen and silk are best ironed with an ironing cloth to prevent shine marks Never iron areas of a garment where perspiration marks are visible as the heat of the iron will fix the stains making them permanent lroning Chart Fabric Acrylic Acetate Silk Nylon Polyester Rayon Viscose Wool Wool Blends Cotton Blends Corduroy Cotton Linen Denim Temperature Setting e eee To MAX ses To MAX Ironing Recommenda
4. the iron soleplate maintains the selected temperature Refillable water tank cover The 600ml capacity tank can be refilled at any time for continuous steam ironing Tap water safe Iron rest Place the iron on the heat resistant iron rest during ironing Boiler on off switch This switch controls the internal boiler It illuminates to indicate that the boiler is switched on and heating Low water indicator The low water indicator illuminates to alert you when it is time to refill the water tank professional ironing system Sach Cord minder A Use the cord minder to keep the iron cord E clear of the ironing surface to prevent it creasing garments during ironing Steam release button Press and hold the steam release button to produce a constant stream of high powered steam to reduce your ironing time and effort Steam will not be emitted from the iron when the steam release button is not depressed Variable temperature dial The variable temperature dial adjusts the temperature of the iron soleplate allowing you to select the desired temperature for each garment iron on off switch This switch controls the element in the iron soleplate It illuminates to indicate that the iron is switched on Steam ready indicator The steam ready indicator illuminates to indicate that the steam function is ready to Variable steam dial use The adjustable steam dial allows you to select the
5. Sunbeam Steam Pro Non Stop Professional lroning System Instruction Booklet SR8500 Please read these instructions carefully and retain for future reference Contents Sunbeam s Safety Precautions Features of your Steam Pro Non Stop Using your professional ironing system Care and cleaning lroning guide Ironing chart Mel AA ell Leu oLblsial agis ye oS S ISS ARS FABIEN Assurez vous que les pr cautions ci dessus relatives a la s curit sont bien comprises Versichern Sie sich daB die obenstehenden SicherheitsmaBnahmen Verstanden werden BeBatdvete mac ol napan vw mpopuAd etc acpadsiac yivovtat katavont s Pastikan bahwa tindakan tindakan keselamatan seperti di atas dimengerti anda Accertatevi che le suddette norme di sicurezza siano comprese a dovere on OO PM SOOT E ERA REE MMB lt EX Yeepete ce peka norope cnomeHaTUTe mepkn Ha npetnasnusoct ce go6po pas6paHun Aseg rese de que las precauciones de seguridad precedentes sean bien comprendidas sighs dys Leien YL glablital aS iS e 1S dawuilen danasetGosmnaaanautiady av EE Vlupdilagu Yukarda belirtilen g venlik nlemlerinin anla ld ndan emin olunuz Xin ki m ch c rang nh ng bi n ph p l m an to n k tr n du gc hi u r SAFETY PRECAUTIONS FOR YOUR PROFESSIONAL IRONING SYSTEM Do not leave a hot iron within reach of children If they come into contact with a hot iron it could lead to serious burns I
6. ed ironing switch the iron and boiler off by moving both switches to the off position Switch the power off at the power outlet and remove the plug Wait for the iron to cool completely before storing Do NOT empty the water tank Refilling the tank during ironing When the water in the tank falls below the minimum level the red low water indicator will illuminate and the iron will stop generating steam 1 Before refilling the tank switch the boiler and iron switches to the off position Switch the power off at the power outlet and remove the plug 2 Lift the water cover and fill the tank Replace the cover 3 Insert the plug into the power outlet and turn the power on 4 Place the boiler and iron power switches in the on position and allow the appliance to heat 5 Recommence ironing when the thermostat light goes out and the green steam ready indicator is illuminated Care and cleaning To clean the exterior of your professional ironing system wipe over with a damp soft cloth and wipe dry Do NOT use harsh abrasives chemical cleaners or solvents to clean the exterior of your appliance as these will damage the surface To clean the stainless steel soleplate use a stainless steel or metal cleaner and rub gently with a damp cloth and wipe dry Do not use scouring pads abrasives or harsh cleaners to clean your stainless steel soleplate as these will scratch and damage the surface Selecting the ironing
7. her Sunbeam appliance visit www sunbeam com au or contact the Sunbeam Consumer Service Line Australia 1800 025 059 New Zealand 09 912 0747 Sunbeam Consumer Hotline Australia 1800 025 059 New Zealand 09 912 0747 www sunbeam com au ZE is a registered Trademark of Sunbeam GE Corporation Limited ACN 000 006 771 Sunbeam Corporation Limited 2003
8. position Both switches will illuminate The steam ready indicator will turn on and off several times during the first minute Note when turned on for the first time your new iron may give off vapours for up to 10 minutes This is due to the initial heating of the materials used It is safe not detrimental to the performance of the iron and will not reoccur 3 Turn the temperature dial on the iron to the desired setting The thermostat light will illuminate to indicate that the iron is heating It will go out once the iron has reached the selected temperature Note when changing the temperature dial from a higher setting to a lower setting allow the iron to cool for at least 2 minutes before continuing ironing 4 Rotate the variable steam dial on the base to select the desired steam level When the green steam ready indicator light comes on and stays illuminated you can commence ironing Before using steam on a garment direct a shot of steam into the air to release any remaining condensation 5 Press and hold the steam release button to iron with steam To dry iron do not press the steam release button Both the steam ready indicator and the thermostat light will cycle on and off during ironing as the ironing system maintains the selected steam pressure and temperature levels Note To prevent water dripping from the soleplate only use the steam function on higher temperature settings ee and above 6 Once you have finish
9. ron only on an ironing board Sunbeam are very safety conscious when designing and manufacturing consumer products but it is essential that the product user also exercise care when using an electrical appliance Listed below are precautions which are essential for the safe use of an electrical appliance Read carefully and save all the instructions provided with an appliance Always turn the power off at the power outlet before you insert or remove a plug Remove by grasping the plug do not pull on the cord Turn the power off and remove the plug when the appliance is not in use and before cleaning Do not use your appliance with an extension cord unless this cord has been checked and tested by a qualified technician or service person Always use your appliance from a power outlet of the voltage A C only marked on the appliance Close supervision is necessary when your appliance is being used near children or infirm persons Never leave an appliance unattended while in use Young children should be supervised to ensure that they do not play with the appliance An iron takes approximately 30 minutes to cool down Do not wind the cord around the soleplate Do not leave the iron unattended while it is plugged into the power outlet Always unplug the iron from the power outlet before filling or emptying the water tank Do not use an appliance for any purpose other than its intended use Do not place an appliance
10. tion Dry iron on wrong side Dry iron on wrong side while still damp or use spray to dampen lron on wrong side Use an ironing cloth to prevent shine marks Iron on wrong side while still damp or use spray to dampen Iron on wrong side while still damp or use spray to dampen Iron on wrong side of fabric Mainly dry iron Steam can be used under manufacturer s instructions Steam iron on wrong side or use an ironing cloth Steam iron on wrong side or use an ironing cloth Check label and follow manufacturer s instructions Use setting for the fibre requiring the lowest setting Steam iron on wrong side or use an ironing cloth and brush to raise the pile Dry iron while still damp or use spray to dampen Use steam medium to high Iron on wrong side or use an ironing cloth to prevent shine marks especially with dark colours Dry iron while still damp or use spray to dampen Use steam medium to high Use maximum steam Sunbeam and Steam Pro are registered trademarks of Sunbeam Corporation Designed in Italy Made in China Due to minor changes in design or otherwise the product may differ from the one shown in this leaflet Backed by Sunbeam s 2 Year Replacement Guarantee and National Service Network Copyright SUNBEAM CORPORATION LIMITED 2003 INCORPORATED IN N S W A C N 000 006 771 Sunbeam Corporation is a division of GUD Holdings Ltd For more information or advice on this or any ot
Download Pdf Manuals
Related Search