installation & operation
Contents
1. 19 20 SUB ZERO ICE MACHINE OPERATION SEQUENCE OF OPERATION Depending on ambient conditions and cold water supply temperature the ice making process will take approximately 30 minutes 1 Initial Start Up or Start Up After Automatic Shut Off Water Fill Before the compressor starts the water inlet valve will purge old water from the system for about 3 minutes 2 Refrigeration System Start Up The compressor starts after the Water Fill cycle and remains on throughout the Freeze and Harvest cycles The condenser fan motor starts and runs throughout the Freeze cycle 3 Freeze The water pump sprays water into the inverted cups The water freezes layer by layer until an ice cube forms in each cup The control system will adjust the length of the Freeze cycle to conditions 4 Harvest The water pump shuts off and the water inlet valve starts up to assist harvest and refill the water sump The evaporator is warmed allowing the cubes to release from the evaporator and drop into the storage bin The control system will adjust the length of the Harvest cycle to conditions and regulate whether the condenser fan will run At the end of the Harvest cycle the ice machine will start another Freeze cycle Step 3 5 Automatic Shut Off The level of ice in the storage bin controls the ice machine shut off When the bin is full ice will contact the bin thermostat bulb holder The bin thermostat bu2. 2 Remove the hinges from the door by removing the four screws two each hinge that secure the hinges to the door Refer to the illustration below Flat Head Screws EE E ca F p Step 2 Step 3 r 4 w A p Leg leveler 12 Securing the ice machine Remove door Remove hinges and plastic trim piece SUB ZERO ICE MACHINE INSTALLATION INSTALLATION 3 Remove the upper plastic trim piece right hand configured from the door by removing the two screws that secure it to the door Then replace it with left hand trim piece Refer to the illustration on page 12 4 Transfer the hinges to the left side of the door and re attach The upper hinge will need to become the lower hinge and the lower hinge will now need to become the upper Refer to the illustration below 5 Remove the top ice machine cover by removing the two screws along the back of the unit Refer to the illustration below 6 7 8 9 Remove four screws from the front top rail Refer to the illustration below Pivot top rail end for end to expose the two left hand top hinge screw holes and reinstall Remove 2 screws from bottom trim plate and slide to cover right hand hinge mounting screw holes and expose left hand hinge mounting screw holes Refer to illustrati
3. 3 16 min Door Panel Weight 15 Ibs 6 8 kg max Dimensions may vary 1 2 3 Remove the handle side bracket attached to the front of the door and set aside Place the door panel lying face down on a protected surface to ensure the front is not scratched or damaged Position the template provided flush with the upper edge of the door Be sure you are following the exact location for the RH or LH door position Refer to the illustration below IMPORTANT NOTE Remember you are viewing the door panel from the back side in the illustration The overall size of the panel shown is the minimum size necessary to cover the door of the unit The exact measurements of your door panel may vary depending on the particular installation you are following Once you have located the proper position for the hardware mark the holes remove template and drill pilot holes for mounting of the hardware We recommend starting the first few holes positioning the hardware drilling remaining pilot holes and securing the mounting brackets with the 8 x 1 2 screws Refer to the illustrations below Flush with Top and Side Template position Right hand door panel Left hand door panel SUB ZERO ICE MACHINE INSTALLATION INSTALLATION A CAUTION Exercise caution when drilling holes for mounting hardware This is especially critical with inset panels Install the door pa
4. 43 C for models UC 1510 and UC 15IPO a The location must not be near heat generat ing equipment a The location must not obstruct air flow through the kickplate airflow is in and out the front of the ice machine The location must allow enough clearance for water drain and electrical connections at the rear of the ice machine a Models UC 15I0 and UC 15IPO may be installed outside A CAUTION The ice machine must be protected if it will be subjected to ambient tempera tures below 32 F 0 C Component failure caused by exposure to freezing tempera tures is not covered by the warranty See page 27 AREA REQUIREMENTS Before moving the ice machine in place be sure the finished opening dimensions elec trical and plumbing locations are accurate Refer to pages 7 11 Be sure your plumber electrician and cabinet installer have this information before finishing work is completed Models UC 15I and UC 1510 are gravity drain models that require a drain tube that is pitched down from the outlet at the back of the unit to the sanitary sewer connection Models UC 15IP and UC 15IPO have a built in drain pump that will pump water up to a drain point such as a nearby sink Refer to specifications on pages 8 9 IMPORTANT NOTE If the ice machine is installed in a corner the door swing may be limited due to handle contact with the wall or cabinet face IMPORTANT NOTE The floor under the ice machine must be at t
5. Refer to page 19 and activate the ice machine Adjust bin thermostat refer to page 21 Verify line is not kinked or crimped then call for service Correct water supply Water pressure must be 20 80 psi 1 4 bar 5 5 bar Clean and sanitize the ice machine refer to pages 23 25 Ambient temperature must be between 50 F and 100 F 10 C and 38 C for models UC 15I and UC 15IP and between 50 F and 110 F 10 C and 43 C for models UC 1510 and UC 15 PO Complete semi annual maintenance refer page 23 SUB ZERO TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE PROBLEM Freeze cycle is long low ice production Ice quality is poor cubes are shallow incomplete or white POSSIBLE CAUSE Water temperature is too high Dirty condenser High air temperature entering condenser Water filtration is poor Water inlet valve stuck open or leaking Water inlet valve is not working Refrigeration problem Kickplate is obstructed Ice machine is dirty Water filtration is poor Water softener is working improperly if applicable Poor incoming water quality Dimensions in parentheses are in millimeters unless otherwise specified POSSIBLE SOLUTION Connect a cold water supply verify check valves in faucets and other equipment are functioning correctly Clean condenser see page 24 Air temperature must not exceed 100 F 38 C for models UC 15I and UC 15IP and 110 F 43 C for models UC 15
6. optional drain pump or pump models UC 15IP and UC 15IPO must be purchased if a gravity drain is not possible Both drain methods require routing to an open site drain Do not connect directly to drain line as bacteria from drain line may contaminate the ice machine The included water filter is designed to inhibit scale formation filter sediment and remove chlorine odor and taste The life expectancy of the water filter is 6 months during normal usage The ice machine control board will monitor water usage and indicate when replacement is required WATER INLET LINES Follow these guidelines to install water inlet lines a Do not connect the ice machine to a hot water supply Be sure all hot water restric tors installed for other equipment are working Check valves on sink faucets dishwashers etc If water pressure exceeds the maximum recommended pressure 80 psi 551 5 kPA obtain a water pressure regulator from your local plumbing contractor a Install a water shut off valve for the ice making water lines a Insulate the water inlet line to prevent condensation DRAIN CONNECTIONS Follow these guidelines when installing drain lines to prevent drain water from flowing back into the ice machine and storage bin Drain lines must have a 11 2 drop per 5 feet of run 2 5 cm per meter and must not create traps The floor drain must be large enough to accommodate drainage from all drains Drain pump disc
7. the CLEAN button once for each additional minute of freeze cycle time desired 3 Five minutes is the maximum additional freeze time that can be added Pressing the CLEAN button 6 times will reset the finish ing time to zero additional minutes Cube weight increases or decreases depending on the amount of dimple in the cube SUB ZERO ICE MACHINE CARE CLEANING You are responsible for maintaining the ice machine in accordance with the instructions in this manual Maintenance procedures are not covered by the warranty A WARNING If you do not understand the procedures or the safety precautions that must be followed call your local Sub Zero author ized service center to perform the main tenance procedures for you We recommend that you perform the following maintenance procedures a minimum of once every six months to ensure reliable trouble free operation and maximum ice production CLEANING SCHEDULE Maintenance Weekly Clean cabinet exterior Sanitize ice bin Replace water filter Clean condenser coil Check ice quality To ensure efficient operation Sub Zero recom mends an annual cleaning performed by a qualified service company The ice machine will require disassembly cleaning and sanitiza tion For the name and number of an author ized service center in your area check the contact and support section of our website or call 800 222 7820 Basic cleaning and maintenance of your
8. 10 and UC 15IPO Replace the filter Turn off ice machine If water continues to enter ice machine the water inlet valve must be replaced Call for service Water inlet valve must be replaced Call for service Call for service Remove obstruction Clean and sanitize the ice machine see pages 23 25 Replace the filter Repair the water softener Contact a qualified service company to test the quality of the incoming water and make appropriate filter recommendations 29 CONTACT INFORMATION Sub Zero customer service 800 222 7820 Website subzero com 30 SERVICE INFORMATION SERVICE INFORMATION If you do need service be sure to have the model and serial number of your unit when you call You ll find these numbers on the rating plate Refer to the illustration on page 4 For warranty purposes you will also need the date of installation and the name of your Sub Zero dealer Record this information below for future reference Model Number Serial Number Installation Date Sub Zero Authorized Service Center and Phone Sub Zero Dealer and Phone BEFORE CALLING FOR SERVICE Before calling a Sub Zero authorized service center refer to the Troubleshooting Guide on pages 28 29 Check the household fuse or circuit breaker to see if it has been blown or tripped and that the electrical connection to the appliance has not been disconnected A power outage may also have caused a disruption in se
9. PERATION CONTROL PANEL FUNCTIONS POWER Button Green Pressing the POWER button once will activate the ice machine and green POWER light Pressing the POWER button a second time will de activate the ice machine Automatic Ice Making Light Blue The ICE light is illuminated when the ice machine is in the ice making position The light is off when the ice machine is in the clean cycle Delay Start Pressing the DELAY button will initiate a delay cycle The ice machine will not run until the delay time expires Pressing the button once will illuminate the 2 hour light and initiate a two hour delay period Pressing the button a second time will illu minate the 4 hour light and initiate a four hour delay period Pressing the button a third time will illumi nate the 8 hour light and initiate an eight hour delay period a Pressing the button a fourth time will cancel the delay cycle ICE MACHINE CONTROL PANEL CLEAN Button Green Pressing the CLEAN button will initiate a clean cycle and de activate the ICE light The CLEAN light will flash during the clean cycle to indicate the proper time to add ice machine cleaner or sanitizer Replace Filter Red When the ice machine completes 8000 freeze harvest cycles the light will illuminate to indicate the filter needs replacement Depress ing the CLEAN button for 6 seconds will reset the counter and light 7 POWER DELAY CLEAN j REPLACE FILTER
10. TOP VIEW 165 1 2 13 LOCATION OF WATER LINE TOP VIEW gt 151 4 min 387 lt ROUGH OPENING WIDTH 24 610 ROUGH OPENING DEPTH LOCATE ELECTRICAL WITHIN POSITION OUTLET WITH GROUNDING PRONG ON RIGHT SHADED AREA es 4 102 FRONT VIEW 341 2 876 ROUGH OPENING HEIGHT 335 8 854 MINIMUM HEIGHT REQUIRED ALL MODELS Overall Width 143 4 375 Overall Height levelers in 335 s 854 Overall Depth 23 584 Minimum Door Clearance 18 457 Rough Opening Width 151 4 387 Rough Opening Height 341 2 876 Minimum Height Required levelers in 335 s 854 Rough Opening Depth 24 610 Dimensions may vary 1 s 3 SUB ZERO ICE MACHINE INSTALLATION LOCATION OF ICE MACHINE The location selected for the ice machine must meet the following criteria If any of these criteria are not met select another location a The ice machine may be built into a cabinet however the location must allow removal of the ice machine for cleaning and servicing Service diagnostics are performed from the top of the ice machine a The location must be free of airborne and other contaminants u Do not place the unit within 18 457 of a trash compactor or trash recycling container The air temperature must be at least 50 F 10 C but must not exceed 100 F 38 C for models UC 15I and UC 15IP and 110 F
11. UNDERCOUNTER ICE MACHINE INSTALLATION amp OPERATION SUB ZERO CONTENTS Ice Machine Installation 4 Installation Checklist 16 Ice Machine Features 17 Ice Machine Operation 18 Ice Machine Care 23 Troubleshooting Guide 28 Service Information 30 Sub Zero Warranty 31 Features and specifications indicated herein and on the website are subject to change at any time without notice Check our website subzero com for the most up to date specifications As you follow these instructions you will notice WARNING and CAUTION symbols This blocked information is important for the safe and efficient installation of Sub Zero equipment There are two types of potential hazards that may occur during installation A CAUTION signals a situation where minor injury or product damage may occur if you do not follow instructions A WARNING states a hazard that may cause serious injury or death if precautions are not followed Another footnote we would like to identify is IMPORTANT NOTE This highlights informa tion that is especially relevant to a problem free installation SUB ZERO is a registered trademark of Sub Zero Inc SUB ZERO ICE MACHINE INSTALLATION AND OPERATION THANK YOU Congratulations on the purchase of your Sub Zero ice machine It produces the same high quality clear ice that you would expect from Sub Zero The importance of the installation of the ice machine cannot be overemphasized Installa tion sho
12. an increase the minimum wire gauge required A qualified electrician must determine the proper wire size although 14 is the minimum size allowed Dimensions in parentheses are in millimeters unless otherwise specified IMPORTANT NOTE Observe correct polarity of incoming line voltage Incorrect polarity can lead to erratic ice machine operation and a safety issue MINIMUM CIRCUIT REQUIREMENT The minimum circuit requirement is used to help select the wire size of the electrical supply Minimum circuit requirement is not the ice machine s running amp load MAXIMUM BREAKER SIZE AND MINIMUM CIRCUIT AMPERAGE Voltage Phase Cycle 115 1 60 Maximum Fuse Circuit Breaker 15 Minimum Circuit Amps 4 1 GFC REQUIREMENTS For Models UC 15I0 and UC 15IPO or if a GFCI ground fault circuit interrupter is required by local electrical code it must be breaker type IMPORTANT NOTE You must follow all National Electrical Code regulations In addition be aware of local codes and ordinances when installing your services IMPORTANT NOTE Plumbing must conform to state and local codes SUB ZERO ICE MACHINE INSTALLATION PLUMBING REQUIREMENTS WATER SUPPLY Prepare water supply line and drain before installation of your ice machine Installation requires a minimum 1 4 ID copper cold water line and compression fitting not supplied Models UC 15I and UC 15I0 are supplied with a drain hose for gravity draining The
13. aner and sanitizer bottles Dimensions in parentheses are in millimeters unless otherwise specified 1 2 3 4 5 6 7 Prepare 4 oz 118 ml of undiluted ice machine cleaner 7013031 only in a container that will fit easily under the lifted water shutters Refer to page 17 to identify the water shutters Press the CLEAN button The ice machine will initiate a 2 minute harvest to remove any remaining ice from the evaporator Remove all ice from the bin Wait 3 minutes until the CLEAN light flashes then add the prepared cleaner by lifting the water shutters and pouring directly into the spray area The ice machine will automatically time out a ten minute cleaning cycle followed by eight rinse cycles and stop The CLEAN light will turn off to indicate the clean cycle is complete This entire cycle lasts approxi mately 30 minutes Prepare 1 tablespoon 15 ml of undiluted ice machine sanitizer 7013033 only in a container that will fit into the same area Press the CLEAN button Wait 3 minutes until the CLEAN light flashes then add the prepared sanitizer by lifting the water shutters and pouring directly into the spray area The ice machine will automatically time out a ten minute sanitizing cycle followed by eight rinse cycles and stop The CLEAN light will turn off to indicate the sanitizing cycle is complete This entire cycle lasts approximately 30 minutes NOTE The ice machine will automati
14. cally continue from the previous point before the clean cycle was initiated a If the ice machine was in the ice making cycle the control board will start ice making again b If the ice machine was in the off cycle the control board will turn off 25 26 SUB ZERO ICE MACHINE CARE WATER FILTER REPLACEMENT To replace the water filter incoming water does not need to be turned off The unit is equipped with an auto bypass feature which bypasses the filter when removed 1 Turn the filter 1 4 turn counter clockwise and it will pop out 2 Reverse the process to re install IMPORTANT NOTE Poor water quality may require more frequent cleaning sanitizing and water filter replacement Water filter replacement SUB ZERO ICE MACHINE CARE ICE MACHINE MAINTENANCE REMOVAL FROM SERVICE LONG TERM STORAGE AND WINTERIZATION Special precautions must be taken if the ice machine is to be removed from service for an extended period of time or exposed to ambient temperatures of 32 F 0 C or below 4 CAUTION If water is allowed to remain in the ice machine in freezing temperatures severe damage to some components could result Damage of this nature is not covered by the warranty Dimensions in parentheses are in millimeters unless otherwise specified Follow the procedure below 1 Perform a cleaning and sanitizing procedure to prevent mildew growth 2 Disconn
15. ce machine stops before the bin is full or runs after the bin is full ambient temperatures are probably high or low and the bin thermo stat can be adjusted as follows A WARNING Power is supplied to ice machine during this procedure Avoid contact with the fan blade and the electrical connections 1 To access the thermostat remove the four screws attaching the kickplate and tilt forward to remove 2 Turn the thermostat to the left to decrease the level of ice before automatic shut off Turn to the right to increase the level of ice before automatic shut off 3 Reassemble the kickplate Bin thermostat tube Bin thermostat Bin thermostat tube Bin thermostat 21 22 SUB ZERO ICE MACHINE OPERATION OPERATIONAL CHECKS CUBE WEIGHT ADJUSTMENT The cube weight can be increased from the factory setting by adjusting the finish time Additional finishing time check 1 Press and hold the POWER button for 5 seconds 2 Count the flashes on the ICE light The light will flash once for each additional minute of freeze cycle time Adjusting finishing time Adjust in 1 minute increments and allow the ice machine to run several freeze harvest cycles then inspect the ice cubes If a heavier cube weight is desired add another minute of freeze time and repeat the process 1 Press and hold the POWER button 2 Press and release
16. ch side of the unit for protruding screw heads Dimensions in parentheses are in millimeters unless otherwise specified Installations on a slab Use a Model UC 15IPO or UC 15IP with built in drain pump and pump the water to the point of drainage Drain pump models will pump 12 feet 3 7 m high Installations over a crawl space or basement If there is not enough room behind the ice machine for a drain waste water receptacle the drain will have to be below the floor 10 SUB ZERO ICE MACHINE INSTALLATION INSTALLATION INSTALLATION PROCEDURE 1 Prepare the site by following the instruc tions under Electrical Requirements and Plumbing Requirements on pages 7 9 2 Remove ice machine from carton 3 Inspect for damage 4 Remove literature warranty packet and drain hose from inside the ice machine 5 Adjust leg levelers Refer to Leveling on page 12 6 Reverse door if desired See pages 12 13 7 Gravity drain model Install drain hose to drain on back of ice machine and route to open site drain Refer to Plumbing Require ments on pages 8 9 Pump model Route drain tubing through drain fitting on the back of the ice machine and install drain hose on drain pump Route other end of drain tubing to drain site Refer to Plumbing Requirements on pages 8 9 8 Use compression fitting to connect the Water Inlet on back of ice machine to the prepared 1 4 ID cold water line Refer to Plumbing Requirements on pag
17. each foot as necessary to level the bin Refer to the illustration below SECURE THE ICE MACHINE To secure the ice machine install two 8 x 1 2 flat head screws through each hinge Refer to the illustration below SIDE PANELS With the Sub Zero ice machine you must securely fasten the side panels to the adjacent cabinets and floor Panels should be fastened to the floor and walls using LU brackets hardware not provided To help you move the unit into place rout out an area in the floor so the L bracket will sit flush with the floor level Brackets and screws are provided for mounting the unit to adjoining cabinets and side panels REVERSE THE DOOR SWING The hinged side of the door may be reversed to the other side if desired The Sub Zero ice machine is shipped with the door hinged at the right The door and hinges are designed for placing the hinges on either the right or the left side of the unit Moving the hinges to the left in the pre drilled holes allows the door to pivot from the left side Refer to the illustrations below IMPORTANT NOTE The plastic molding which covers the top area of the door packaged with the ice machine is required for this procedure 1 To begin remove the four screws that secure the door hinges to the ice machine Refer to the illustration below NOTE Remove the shim located between the cabinet and bottom hinge this shim will transfer to the left side bottom hinge
18. ecessary to remove the knock out in the hinge cover when the 90 degree door stop is used m Door Stop Pin 90 degree door stop Dimensions in parentheses are in millimeters unless otherwise specified Hinge cover installation CONTACT INFORMATION Sub Zero customer service 800 222 7820 Website subzero com 16 SUB ZERO ICE MACHINE INSTALLATION INSTALLATION CHECKLIST IMPORTANT NOTE To ensure a safe and proper installation the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked Any questions or problems about the installa tion should be directed to your Sub Zero dealer or Sub Zero customer service at 800 222 7820 You can also visit our website at subzero com Check to see if the unit is operating before you install If not is the unit plugged in Is the water turned on If applicable is the door panel installed properly Have any installation or service problems been noted on the product registration card Instruct the owner to register the product Is the ice machine level Has all of the internal packing been removed Have all of the electrical and water connec tions been made Has the supply voltage been tested and verified against the information on the rating plate Is there proper clearance in front of the kickplate for air circulation Has the ice machine been installed where ambient t
19. ect the electric power at the circuit breaker or the electric service switch 3 Turn off the water supply 4 Remove the water from the water reservoir 5 Disconnect and drain the incoming ice making water line at the rear of the ice machine 6 Disconnect vinyl hose from water pump and allow to drain 7 Make sure water is not trapped in any of the water or drain lines Compressed air can be used to blow out the lines 8 Use a spray bottle and a solution of 1 table spoon 15 ml sanitizer to 1 gal 4 L water and spray all interior surfaces Do not rinse allow to air dry 9 Block the door partially open to provide air exchange and prevent mildew growth 27 SUB ZERO TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE PROBLEM Ice machine will not run SERVICE CENTER Contact your Sub Zero dealer or check the Locator section of our website subzero com for the authorized service center nearest you Ice machine runs and no ice is produced 28 POSSIBLE CAUSE No electrical power to the ice machine POWER button has not been depressed Bin thermostat incorrectly adjusted Drain pump safety switch is open No water to ice machine Incorrect incoming water pressure Spray nozzles blocked with mineral buildup Ambient temperature is too high or low Water filter is clogged POSSIBLE SOLUTION Replace the fuse reset the breaker turn on the main switch or plug in ice machine
20. emperatures will remain in the range of 50 100 F 10 38 C for models UC 15I and UC 15IP and 50 110 F 10 43 C for models UC 15I0 and UC 15IPO Has the ice machine been installed where the incoming water temperature will remain in the range of 50 80 F 10 27 C Is the ice machine drain line routed to an open site drain for gravity drains and per instructions for pump units Has the owner operator been instructed regarding maintenance and the use of cleaner and sanitizer Has the ice machine and bin been sani tized Have the water and drain connections been examined for leaks NOTE If air temperature is less than 60 F 16 C water temperature must be equal to or greater than 50 F 10 C If you are storing or disposing of your old refrigerator freezer or ice machine please do it safely Remove the doors or tightly secure the doors closed Child entrap ment accidents can be tragic SUB ZERO ICE MACHINE FEATURES ICE MACHINE FEATURES Undercounter ice machine u Models UC 15I and UC 1510 have a gravity drain while Models UC 15IP and UC 15IPO have a built in pump to allow greater instal lation flexibility 24 610 depth design for a complete integrated look Door accepts custom panels Automatic ice maker provides high quality clear ice a Ice storage bin capacity of up to 25 Ibs 11 kg Automatic defrost Reversible door swing Front venting with removable k
21. es 8 9 9 Open the shut off valve on the water line 10 Check all visible connections for water leakage Failure to do so could cause flooding 11 Connect electrical plug to grounded three prong polarized outlet See Electrical Requirements on page 7 A WARNING The ice machine must be grounded in accordance with national and local electrical codes Do not use an extension cord or adapter Improper water supply and drain connec tions can result in personal injury and substantial property damage These connections are the responsibility of the owner operator 12 Place ice machine back in position and check leveling again Make any necessary adjustments Drain Fitting Water Inlet Connect to drain Dimensions in parentheses are in millimeters unless otherwise specified SUB ZERO ICE MACHINE INSTALLATION INSTALLATION 13 Prepare sanitizer solution and sanitize the ice machine according to In Place Cleaning Sanitizing Steps 6 and 7 on page 25 14 Put one gallon 4 L of cold water into a container that will easily pour under the lifted water shutters Refer to page 17 to identify water shutters Open shutters and add one gallon 4 L of cold water Watch for proper drainage 15 Press POWER button 16 At initial start up ice machine will need approximately 30 minutes to freeze ice and up to 5 minutes to harvest the ice Wait for first cycle
22. harge line must termi nate at an open site drain Maximum rise 12 feet 3 7 m Maximum run 100 feet 30 5 m APPROXIMATE HEIGHT OF ICE MACHINE DRAIN Standard installation 5 127 A CAUTION Improper drainage can lead to water flowing back into ice machine and poor performance SUB ZERO ICE MACHINE INSTALLATION PLUMBING REQUIREMENTS WATER SUPPLY AND DRAIN LINE SIZING CONNECTIONS Water Water Ice Machine Tubing Size up to Temperature Pressure Fitting Ice Machine Fitting Ice Making 50 F 10 C Min 20 psi 137 9 kPA Min 1 4 6 4 ID 1 4 6 4 minimum IMPORTANT Water Inlet 80 F 27 C Max 80 psi 551 5 kPA Max Copper Tubing inside diameter NOTE Water Outlet 3 4 19 3 4 19 minimum UC 15I and Hose Barb inside diameter Plumbing must UC 15I0 conform to state and local codes Water Outlet 3 g 9 5 3 g 9 5 UC 15IP and Hose ID minimum UC 15IPO NOTE If air temperature is less than 60 F 16 C water temperature must be equal to or greater than 50 F 10 C IMPORTANT NOTE Although the ice machine has been designed to be serviced in place in some cases it may be necessary to pull the unit out for service For that reason do not restrict access to the unit at the front top and bottom If a floor is to be installed after the ice machine shims the thickness of the floor should be installed under the unit to keep the ice machine level with the floor Also allow 1 3 3 clearance on ea
23. he same level as the surrounding finished floor IMPORTANT NOTE When you move the unit using a hand truck or dolly position the dolly on the side of the unit and secure the door so it does not open while transporting the unit A CAUTION Any finished flooring should be protected with appropriate material to avoid any damage from moving the unit SUB ZERO ICE MACHINE INSTALLATION ELECTRICAL REQUIREMENTS Prepare electrical circuit before installation of your ice machine Installation requires a grounded three prong polarized receptacle with a separate fuse circuit breaker in an elec trical service box VOLTAGE Do not use an extension cord or two prong adapter Electrical ground is required on this appliance Do not remove the power supply cord ground prong All electrical work including wire routing and grounding must conform to local state and national electrical codes The following precau tions must be observed The ice machine must be grounded a A separate fuse circuit breaker must be provided for each ice machine The maximum allowable voltage variation is 10 of the rated voltage at ice machine start up when the electrical load is highest The minimum wire size is 14 for less than 100 feet 30 5 m or 12 for more than 100 feet 30 5 m to 200 feet 61 m solid copper conductor only The recommended breaker is 15 amp Local or state electrical code length of run or materials used c
24. ice machine will increase its reliability increase performance and help save on water and power consumption Ice production will be maintained and unwanted repairs due to main tenance issues will be minimized After prolonged Semi annual shutdown At start up Poor water quality may require more frequent cleaning sanitizing and water filter replacements 23 24 SUB ZERO ICE MACHINE CARE EXTERIOR CLEANING Clean the area around the ice machine as often as necessary to maintain cleanliness and effi cient operation Use cleaners designed for use with stainless steel products Sponge any dust and dirt off the outside of the ice machine with mild soap and water Wipe dry with a clean soft cloth Heavy stains should be removed with stainless steel wool Never use plain steel wool or abrasive pads They will scratch the panels CLEANING THE CONDENSER Disconnect electric power to the ice machine at the electric service switches before cleaning the condenser A dirty condenser restricts airflow resulting in excessively high operating temperatures This reduces ice production and shortens compo nent life Clean the condenser at least every six months Follow the steps below 1 Remove the four screws attaching the kick plate and tilt forward Clean kickplate openings before replacing 2 Clean the outside of the condenser with a soft brush or a vacuum with a brush attach ment Clea
25. ickplate allows unit to be serviced from the front Solid core door with gasket and door closer UL approved for US and Canada Two five and twelve year residential warranty exclusions apply see warranty at the end of this guide MODELS UC 151 UC I15IP UC I51O amp UC I5IPO Ice Machine Control panel Water shutters Water reservoir Large capacity ice storage bin Water filter Kickplate Rating plate Dimensions in parentheses are in millimeters unless otherwise specified Reversible door hinge Ice scoop Gasket Bin light WARRANTY Sub Zero products are covered by a two five and twelve year resi dential warranty exclusions apply See warranty details at the end of this guide 17 18 SUB ZERO ICE MACHINE OPERATION BEFORE STARTING THE ICE MACHINE SANITIZE It is important to clean and sanitize the ice machine prior to use to ensure optimum ice quality To ensure proper operation follow the Opera tional Checks on pages 20 22 Starting the ice machine and completing the Operational Checks are the responsibilities of the owner operator Adjustments and maintenance procedures outlined in this manual are not covered by the warranty Do not operate equipment that has been misused abused neglected damaged or altered modified from that of original manufactured specifications A WARNING Do not store food or beverage in the ice machine SUB ZERO ICE MACHINE O
26. lb cools which stops the ice machine The ice machine remains off until ice no longer contacts the bin thermostat bulb holder and the thermostat bulb warms up The increase in temperature will restart the ice machine Step 1 OPERATIONAL CHECKS Sub Zero ice machines are factory operated and adjusted before shipment Normally new installations do not require any adjustment To ensure proper operation always follow the Operational Checks when starting the ice machine for the first time after a prolonged out of service period after cleaning and sanitizing NOTE Routine adjustments and maintenance procedures are not covered by the warranty WATER LEVEL The ice machine maintains the correct water level The water level is not adjustable BIN THERMOSTAT ADJUSTMENT The bin thermostat stops the ice machine when the bin is full Turn the thermostat to the left to decrease the level of ice in bin or to the right to increase the level of ice in bin SUB ZERO ICE MACHINE OPERATION OPERATIONAL CHECKS TESTING AND ADJUSTING THE BIN THERMOSTAT The bin thermostat stops the ice machine when the bin is full It is preset for normal ambient temperatures and adjustments are usually not required The thermostat is functioning correctly if when three ice cubes are placed on the ther mostat tube for 5 minutes the ice machine stops The ice machine should restart 5 minutes after the cubes are removed If the i
27. n from top to bottom not side to side Be careful not to bend the condenser fins 3 Shine a flashlight through the condenser to check for dirt between the fins If dirt or grease remains between the fins or the condenser fins are bent or flattened consult your service representative SUB ZERO ICE MACHINE CARE INTERIOR CLEANING Perform an in place cleaning sanitizing proce dure monthly and a cleaning sanitizing proce dure every 6 months for efficient operation If the ice machine requires more frequent cleaning and sanitizing consult a qualified service company to test the water quality and recommend appropriate water treatment An extremely dirty ice machine must be taken apart for cleaning and sanitizing A CAUTION Damage to the ice machine evaporator caused by incorrect chemical usage is not covered by the warranty Use only Sub Zero approved ice machine cleaner 7013031 and sanitizer 7013033 only IN PLACE CLEANING SANITIZING This procedure allows semi annual in place cleaning of all surfaces that come in contact with the water system IMPORTANT NOTE Contact qualified service personnel for disassembly The quality of your potable water supply may require more frequent cleaning intervals Use ice machine cleaner to remove lime scale or other mineral deposits Ice machine sani tizer disinfects and removes algae and slime NOTE All ice must be removed from the bin Follow all labels and warnings on cle
28. nel by engaging the tabbed bracket to the door first and then sliding the hinge side hardware over the positioning screws You will have a 1 4 inch adjustment up and down side to side with this hardware Once you have the door in place attach the remaining 8 x 1 2 screws to the hinge side mounting bracket and install decorative caps A CAUTION If the reveal on the hinge side of the door panel is less than 1 4 and the panel has a square corner severe finger pinching or damage to the unit may occur 90 DEGREE DOOR STOP The Sub Zero ice machine has a 90 degree door stop Follow these steps for installation 1 Open the door approximately 80 degrees 2 Insert the stop pin into the bottom door hinge pin enters from the top The pin must be inserted until the head has made contact with the hinge body Refer to the illustration below 3 Insert the stop pin into the top door hinge pin enters from the bottom 4 Check for proper operation HINGE COVER INSTALLATION IMPORTANT NOTE Install the hinge covers after installation of the ice machine is complete The 90 degree door stop must be installed prior to installing the hinge covers 1 Remove the backing paper of the adhesive pads and bond to the hinge 2 Install center covers magnets will secure these covers Refer to the illustration below IMPORTANT NOTE Hinges must be free of dirt or grease before applying covers IMPORTANT NOTE It will be n
29. of cubes to drop to ensure proper installation INSTALLATION SPECIFICATIONS Gravity drain model TOP VIEW SHUT OFF WATER VALVE INLET TUBE gt lt 1 8 3 gt lt lt 151 4 min gt 387 OPENING WIDTH TOP VIEW WATER INLET TUBE SHUT OFF VALVE op FRONT VIEW A CAUTION Do not cover the kickplate area The unit must be allowed to have ventilation through these fins The door panel may hang in front of the fins but a decorative kickplate must not cover the fins The kickplate can be painted another color if you choose Follow these easy steps Rough up surface to be painted with fine grit sandpaper u Wipe with alcohol to ensure it is clean and dry a Use an appliance or industrial grade oil base high gloss enamel paint INSTALLATION SPECIFICATIONS Pump model TOP VIEW SHUT OFF VALVE WATER INLET TUBE DRAIN TUBE AIR GAP DEVICE eo _ 1 8 3 lt 151 4 min gt 387 OPENING WIDTH TOP VIEW AIR GAP DEVICE DRAIN TUBE WATER SHUT OFF INLET TUBE FRONT VIEW SUB ZERO ICE MACHINE INSTALLATION INSTALLATION LEVELING 1 Adjust the levelers close to desired height 2 Move the bin into its final position 3 Level the ice machine to assure that the bin door closes and seals properly Use a level on top of the bin Turn the base of
30. on below Install the door using the left hand door mounting holes Install shim removed in step 1 between the hinge and cabinet 10 Check the operation of the door by opening g r D Step 4 t p r 4 YW A k Step 8 Transfer hinges and reattach Remove top cover Remove front top rail Slide bottom trim plate 13 PANEL DESIGN Additional panel design information can be found in the Sub Zero design guide Check our website at subzero com 14 SUB ZERO ICE MACHINE INSTALLATION INSTALLATION DOOR PANEL INSTALLATION You should be sure of the door panel size and placement before proceeding with the installa tion If you have questions contact your Sub Zero dealer or cabinet supplier Instruc tions regarding sizing of the door panel are provided in the Sub Zero design guide For door handle hardware a D style pull centered on the edge opposite the door hinge side is recommended Screw heads may have to be countersunk to ensure that the hardware does not interfere with the panel fitting flush with the unit door DOOR PANEL DIMENSIONS Door Panel Width 1 s 3 reveal 15 381 Door Panel Height 1 s 3 reveal 4 102 toe space 303 s 772 Door Panel Thickness 5
31. ondensing unit THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB ZERO WILL PROVIDE EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW SUB ZERO WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIES OR ANY OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STATUTORY Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limita tion or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state To receive parts and or service and the name of the Sub Zero authorized service center nearest you contact your Sub Zero dealer distributor or the Sub Zero Customer Service Department P O Box 44130 Madison Wiscon sin 53744 4130 check the Contact amp Support section of our website subzero com or call 800 222 7820 Stainless Steel classic platinum and carbon doors panels product frames and stainless interior surfaces are covered by a limited 60 day parts and labor warranty for cosmetic defects Replacement water filter and air purification cartridges are not covered by the product warranty 31 SUB ZERO INC P O BOX 44130 MADISON WI 53744 4130 800 222 7820 SUBZERO COM 7012206 REV B 000002628 6 2009
32. onnecting tubing FULL TWO YEAR WARRANTY For two years from the date of original installation your Sub Zero warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship LIMITED SIXTH THROUGH TWELFTH YEAR SEALED SYSTEM WARRANTY From the 6th through the 12th year from the date of original installation your Sub Zero warranty covers all parts that prove to be defective in materials or workmanship in the sealed system parts only The sealed system consists of the compressor condenser evaporator drier and all connecting tubing TERMS APPLICABLE TO EACH WARRANTY All service provided by Sub Zero under the above warranty must be performed by an authorized Sub Zero service center unless otherwise specified by Sub Zero Service will be provided in the home during the normal business hours This warranty applies only to products installed for normal residential use Details regarding a non residen tial warranty are available upon request The warranty applies only to products installed in any one of the fifty states of the United States the District of Columbia or the ten provinces of Canada This warranty does not cover any parts or labor to correct any defect caused by negligence accident or improper use maintenance installation service or repair including but not limited to improper removal and reinstallation whether in the unit or at a remote location of the c
33. rvice PRODUCT REGISTRATION Register your new Sub Zero today so that we may ensure your satisfaction You may register by one of the following options 1 Mail in the completed Sub Zero product registration card 2 Register online at subzero com 3 Register by phone by calling the Sub Zero customer service department at 800 222 7820 The model and serial numbers of your unit are printed on the enclosed Sub Zero product registration card If you provide us with your e mail address we will send you exciting new product updates and recipes as they become available along with information on special events The information and images in this book are the copyright property of Sub Zero Inc Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub Zero Inc Sub Zero Inc all rights reserved Sub Zero Products Limited Warranty RESIDENTIAL USE ONLY FULL FIVE YEAR SEALED SYSTEM WARRANTY LIMITED SIXTH THROUGH TWELFTH YEAR WARRANTY ON THE SEALED SYSTEM FULL TWO YEAR WARRANTY ON TOTAL PRODUCT FULL FIVE YEAR SEALED SYSTEM WARRANTY For five years from the date of original installation your Sub Zero warranty covers all parts and labor to repair or replace any components that prove to be defective in materials or workmanship in the sealed system The sealed system consists of the compressor condenser evaporator drier and all c
34. s the right to make design changes and or improvements at any time Specifications and designs are subject to change without notice A WARNING Do not operate equipment that has been misused abused neglected damaged or altered modified from that of original manufactured specifications CONTACT INFORMATION Sub Zero customer service 800 222 7820 Website subzero com PRODUCT REGISTRATION CARD The packet containing this manual also includes warranty information Warranty coverage begins the day your new ice machine is installed IMPORTANT NOTE Complete and mail the product registration card as soon as possible to validate the installation date If you do not return your product registration card Sub Zero will use the date of sale to the Sub Zero dealer as the first day of warranty coverage for your new ice machine ACCESSORIES Optional acces sories are available through your Sub Zero dealer To obtain local dealer information visit the Showroom Locator section of our website subzero com SUB ZERO ICE MACHINE INSTALLATION ICE MACHINE REQUIREMENTS Models UC 15I and UC 15I0 must have open site gravity drain available see page 8 A grounded polarized electrical power supply on a separate circuit servicing only this appliance is required If GFCI ground fault circuit interrupter is required by your local electrical code or in an outdoor instal lation it must be breaker type not outlet t
35. uld be done by a qualified installer Before you begin the installation process it is recommended that you read the entire installation instructions There are key details that you should take special care to observe during the installation By reading these instructions carefully you will make the installation process easier problem free and most importantly safe Any questions or problems about the installation should be directed to your Sub Zero dealer or Sub Zero customer service at 800 222 7820 You can also visit our website at subzero com The Sub Zero ice machine is protected by a warranty that is one of the finest in the industry Take a moment to read the warranty statement on page 31 and refer to it should service become necessary The operation information in this book will answer most of your questions about the features operation and maintenance of your ice machine If you have questions that are not addressed here call Sub Zero customer service at 800 222 7820 or visit our website at subzero com IMPORTANT NOTE Your Sub Zero ice machine is designed and manufactured with the highest regard for safety and perform ance It meets or exceeds the standards of UL and CUL Sub Zero assumes no liability or responsibility of any kind for products manu factured by Sub Zero that have been altered in any way including the use of any parts and or other components not specifically approved by Sub Zero Sub Zero reserve
36. ype see page 7 Must have cold water supply line available at ice machine see page 8 Clearance and air temperature requirements must be met see page 6 If built into a cabinet ice machine must be removable for yearly cleaning procedure see page 23 MODEL SERIAL NUMBER LOCATION Models UC 15I UC 15IF UC 15I0 amp UC 15IPO Rating plate Proper installation requires connection to the water supply a drain and a dedicated electrical circuit These connections are the responsibilities of the owner operator Improper connections can result in personal injury substantial property damage and erratic machine operation If you are unsure of your ability to safely connect the ice machine consult qualified professionals or contact Sub Zero IMPORTANT NOTE Failure to follow these installation guidelines may affect warranty coverage The model and serial number are listed on the rating plate in the upper left corner of the ice bin and on the back of the unit Refer to the illustration below Dimensions in parentheses are in millimeters unless otherwise specified SUB ZERO ICE MACHINE INSTALLATION OVERALL DIMENSIONS Models UC 151 UC 15IP UC 1510 amp UC 15IPO Wk gt tu 43 335 8 854 335 8 854 215 16 143 4 375 T gt 541 115 DOOR SWING 215 16 541 FRONT VIEW SIDE VIEW Does not include door panel INSTALLATION SPECIFICATIONS
Download Pdf Manuals
Related Search