Design Solutions - Sub
Contents
1. CABINET DOOR PANEL SIDE VIEW TRADITIONAL FRAME 3 8 OFFSET A ALL REVEALS ARE 1 4 INCH 6MM Illus 7 Study these illustrations in detail Rest assured the Sub Zero units are compatible with framed cabinet installations IMPORTANT NOTE Refer to the full scale illustrations in the center of this guide for specifics on panels and door openings A CAUTION As the reveal between cabinets and the 700 Series unit decreases the potential exists for severe finger pinching or crushing if a hand or fingers are placed in the opening when the door is closing 700 SERIES PLA INFORMATION A CAUTION Installation Options illustration 9 shows some typical installations and their When 5 8 inch or larger panels are used and a reveal i dimension considerations less than 1 4 inch is maintained the door panels may cause damage to the Sub Zero unit when the door is IMPORTANT NOTE The front of the Sub Zero 700 Series open at the maximum 105 degree stop You should Unit is 24 inches from the back wall Your design may use the built in 90 degree stop to prevent damage necessitate moving the unit back or cabinets forward to SPECIAL NOTE In an installation where you are plac achieve a flush fit ing two 700 Series tall units next to one another and providing a 1 4 inch reveal refer to illustration 8 you cannot assume the panel size is 261 2 inches as shown on the top The panels will need to be 265 s2. Illus Illus 4 Door Panel Specifications Model 2as 249R 249FF 249FFI 506 W Door Panel 23 235 8 235 8 235 8 235 8 17 Door Panel 28 30 30 30 30 133 16 W Lower Panel 17 H Lower Panel 111516 A Handle Recess Location 15 15 15 15 81 Model 245 requires no handle recess 400 Series Door Frame Dimensions Ha pe Rall Stile DOOR FRAME PROFILE hus G IMPORTANT NOTE Rails and stiles must be a minimum of 2 1 4 wide except for the rails of Models 427 and 427R which must be wide enough to cover the door hinges The back sides of rails and stiles that will be visi ble through the glass door will need to be finished NOTE illustration G is typical of the Model 424 door frame pro file details of the other 400 Series door frames will vary slightly SUB ZERO 12 YEAR PROTECTION PLAN Full 5 Year Warranty and Limited 6th Through 12th Year Warranty on the Sealed System Full 2 Year Warranty on Total Product Full Five Year Warranty For five years from the date of original installation the Sub Zero warranty covers all parts and labor ta repair or replace components that prove to be defective in materials or workmanship in the sealed sys tem The sealed system consists of the compressor condenser evaporator drier and all connecting tubing Full Two Year Warranty For two years from the date of original installation the Sub Zero w
3. T to the solid door butin either instance you should consid er using raised panels with a minimum thickness of 5 8 When using a raised framed panel you must allow for an edge to rout around the panel to ensure a proper fit See illustration8 84 2134 With the framed Model 430 you will receive an extruded handle identical in appearance to the 600 Series units However it will be an extended handle and will enable you to use raised panels without providing finger clearance to open the door CENTERED VERTICALLY axo 675 1724 DOOR FRAME 273 Refer to the Framed Panel Specifications chart for complete details on the size of the framed panel Framed Door Panel W x H 281 8 x 6711 16 Minimum Width of Rails and Stiles 21 4 er 4 TOE Door Panel Weight Limit 25 lbs FRONT VIEW o space SIDE VIEW FINCH ADJUSTMENT IN LEVELING LEGS Minimum Panel Thickness 5 8 Illus 9 Illus 8 MODEL 430 CABINETRY DIMENSIONS I Trim reveal 1 4 min EJ Rout to 1 4 thickness 2835022 DOOR FRAME 2134 68 1727 DOOR PANEL CENTERED VERTICALLY Model 430 Overlay Panel Your overlay unit will be shipped without handle hardware and with an 1 overlay pan
4. NG INFORMATION Electrical A 115 volt 60 Hz 15 amp fused electrical supply is required It is recommended that a separate circuit serv ing only this appliance be provided All Sub Zero 600 Series units are equipped with a power supply cord with a 3 prong grounding plug and it must be plugged into a mating 3 prong grounding type wall recep tacle Follow the National Electrical Code and local codes and ordinances when installing the receptacle Refer to illustration 1 page 9 for exact specifications Checking The Results The 600 Series Installation Guide packed with the appli ance will give you step by step procedures for making sure the unit is installed properly The following is a checklist of some of the important items you ll want to review before your installation is complete Following these guidelines will assure a beautiful and safe installation and a satisfied client Has blocking been completed Is the unit leveled properly a solid floor Is the toe plate installed Have electrical and plumbing hookups been made accordance with the 600 Series Installation Guide 1 Are panels installed correctly Are the doors adjusted Does your customer understand the unit s operation Have you given your customer the warranty package When you ve completed this final check you can be assured that your client will enjoy the very best in home refrigeration for ye
5. INCH ADJUSTMENT IN LEVELING LEGS Illus 4 MODEL 427R OVERALL DIMENSIONS 27 24 a 261664 DOOR FRAME gt E DIMENSION 14 356 Z T 16 20 444 1139 DOOR 102 FRAME 273 WITH CENTERED HINGES JERTICALLY t 80 2032 788 9 1997 HOw 8 FRONT VIEW ADJUSTMENT IN LEVELING LEGS gt it l SIDE VIEW Illus 5 400 SERIES PL MODEL 427 CABINETRY DIMENSIONS 27 24 686 S gt FINISHED OPENING CABINET DIMENSION 268 676 DOOR PANEL 1 L T m 80 2032 FINISHED OPENING 75i 793 1924 2026 TRIMMED PANEL DOOR G A ER 4 4 102 102 TOE SPACE FRONT VIEW TOE SPACE SIDE VIEW ADJUSTMENT IN LEVELING LEGS lilus 6 MODEL 427R CABINETRY DIMENSIONS 24 610 CABINET DIMENSION 686 FINISHED OPENING lt 263676 DOOR PANEL 80 451 2032 1149 FINISHED OPENING 1 793 Es 2026 TRIMMED Y T7 DOOR 13 263 67 4 cnm DRAWER PANEL 6 1 1 34 877 16 421 e 102 102 r SIDE VIEW TOE SPACE FRONT VIEW TOE SPACE ADJUSTMENT IN LEVELING LEGS Illus 7 INFORMATION 26 x 753 4 Door Panel W x Min
6. 2 Filler Strip top view Optional 90 Door Stop Available en ee z ee eee 23 Ys to rear of Sub Zero Main Frame 0 ier Ma i i ce rei i y Hi v e u ning m n iuis oie c Re eio asi ER Gb am E RS GE Gb an GUN dia 112 ee E q r H 4 13 F 1 1 pee pA w m m 2 234 23 4 mm usi un um scum ium mur iocum or orc 1i a k n Hn 31a FAT T T ilius illustration C lets you see what considerations you need to make for any overlay panel applications and how they may interact with adjacent cabinets and or countertops Also refer to page 11 INSTALLATION OF TALL UNIT DOOR CLOSED TOP VIEW FULL SCALE FRAMELESS CABINETRY PANEL WEIGHT LIMITS Door 40 Ibs Drawer 12 ibs each LINE OF INTERFERENCE MAXIMUM DOOR OPENING po MOUNTING BRACKET SCREW SEE PAGE 24 FOR PATTERN DIMENSIONS 254 657 APPLIANCE DOOR WIDTH SIDE MOLDING AND INSTALLATION HARDWARE LINE OF INTERFERENCE INSTALLATION OF TALL UNIT DOOR
7. 34 to 45 degrees e 700 One Zone minus five to plus five degrees e 700BF I One Zone minus five to plus five degrees e 700TC I Two Zones Cabinet 34 to 45 degrees Drawers minus five to plus five degrees 700 SERIES PL INFORMATION SERIES Planning Information Be sure your installer has this information before finishing work is completed Before moving the units into place be sure the finished dimensions electrical and plumbing locations and mini mum drawer and door clearances are accurate See illus tration 1 Illus 1 PRE INSTALLATION SPECIFICATIONS TOP VIEW TOP VIEW 13 133 BRACKET ANTI TIP 38 BRACKET 134 343 B 343 9 WATER LINE 151 394 229 SIDE ENTRY WATER LINE LOCATIONS BOTTOM ENTRY LOCATION METTRE alk tte gt 1468 FRONT VIEW SIDE VIEW 27 686 NOTE ORIENT GROUND PRONG TO RIGHT AS SHOWN ANTI TIP BRACKET WATER LINE REAR ENTRY LOCATION p HEIGHT OF BASE UNIT 9 229 WATER LINE SIDE ENTRY LOCATION 5 609 ANTI TIP BRACKET VH N ANTI TIP N BRACKET Se M 700 SERIES P Overall Size Specifications In trying to understand the different units avail able for your use keep in mind you have two size configurations Tall Unit 80 h x 27 w x 24 d Base Unit 341 2 h x 27 w x 24 d The height of the tall unit is set at
8. LEVELING LEGS SIDE VIEW Illus 2 OVERALL DIMENSIONS TALL UNIT TOP VIEW _ 25 657 MAXIMUM OPENING 417 THIS DIMENSION MAY VARY DEPENDING ON INSTALLATION PANEL THICKNESS AND HANDLE HARDWARE 90 OPENING illus 3 700 SERIES P INFORMATION OVERALL DIMENSIONS BASE UNIT 27 CABINET DIMENSIO CABINET DIMENSION 80 MOUNTING DETAIL o o 93 248 Y 4 FRONT VIEW tal INCH ADJUSTMENT IN LEVELING LEGS SIDE VIEW TOP VIEW Illus 4 Illustrations 5 and 6 show hypothetical installa FRAMELESS CABINETRY TALL UNIT tions within frameless and framed cabinets 24 261 Review these with particular attention given to overall panel specifications IMPORTANT NOTE The height of a cabinet door can exceed 451 4 inches with little prob lem However you do not want to go smaller than this height See the following pages For the bottom drawer the maximum panel height is 169 16 inches It is critical to keep a minimum of a 4 inch toe kick area free of panel to allow the unit to function efficiently IMPORTANT NOTE Refer to the full scale illustrations in the center of this guide for specifics on panels and door openings 6 420 4 TOE 102 SPACE FINISHED OPENING SIDE VIEW FRONT VIEW A ALL REVEALS ARE 1 4 INCH 6MM DIMENSIONS MAY VARY 5 I
9. 46 47 Sub Zero 12 Year Protection Plan Warranty Information 48 Creating Solutions for Home Refrigeration Needs Sub Zero s 600 Series offers you the most complete set of design options in built in refrigeration for all of its models From the classic look of the framed unit to the profes sional treatment of the wrapped stainless steel door to the beauty of overlay models Sub Zero has it all The accompanying illustrations show stainless steel over lay and framed unit configurations applied to the Model 650 Note how the different looks are qualified with model number suffixes There are two exceptions to the design designations for each model Models 680 and 690 come only in framed and stainless steel applications Model 561 will maintain the 500 Series look for the framed application and will not be offered in the overlay Model 650 S Stainless Steel Model 650 0 Overlay format It will however be offered in a stainless steel ver sion with wrapped doors All stainless steel models come with a standard 11 inch heavy duty louvered grille one inch diameter stainless steel handles and a stainless steel toe kick Overlay models come with no handle hardware The beau ty of this design is that you can match the surrounding cabinetry hardware Sub Zero does offer optional handles featuring the craftsmanship and attention to detail Sub Zero is famous for These models come with a
10. 80 inches You can allow the top of the door panel to exceed this dimension with caution If you are working with 84 inch or even 96 inch neighboring pan els you can order door panels to match this height Refer to the illustrations on the following pages Other critical dimensions regarding the door swing drawer openings and toe plate are also noted in the Overall Dimensions illustrations Cabinet Applications The 700 Series of refrigeration is compatible with virtually any style and look of cabinetry The units can be used with framed as well as frame less cabinets Because of the precise application and the look you may want to achieve there are important questions you need to answer before ordering panels for the doors drawers As you look at styles of cabinets keep some important facts in mind Weight Limitations The door panel cannot exceed 40 pounds and a drawer panel must not exceed 12 pounds Panel Thickness Panels must be a minimum of 5 8 inch thick Panel Hardware We recommend using D style pulls and they should be located on the opposite side from the hinge centered on the cabinet door and the top center area of the drawer panel INFORMATION OVERALL DIMENSIONS TALL UNIT 686 gt 609 gt CABINET DIMENSION CABINET DIMENSION 14 356 EE MOUNTING DETAIL DRAWER MOUNTING DETAIL r tt Y 4 FRONT VIEW 1 3 INCH ADJUSTMENT
11. Model 700TR Model 700BR Model Model 700 Distinct Temperature Zones 3 2 1 1 Adjustable Glass Shelves Oo 7 74 l 2 Heo Me VN catt Removable Crisper Cover Storage Drawers Removabl Drawer Dividers 2 2 2 justable Dairy Compartment Egg Container Automatic Ice Maker Automatic Defrost Annual energy costs are based on 8 67 cents per kilowatt hour Model 700TR Model 700BR Models 700TF 700TFI 700 SERIES SPECIFIC ONS AND FEATURES Refrigerator Freezer All Freezer All Freezer Combination Combination a 204 42 gt 2 WS M LL eus eran shaq s s s A hueco Rn eque 77 pe Door Drawer Clearance 191 2 191 2 251 2 251 2 ES os on peperere cm EE C E MIR Nera u ere us ee YES dif ane Shipping Weight 55525222 a 77 Model 700BF Distinct Temperature Zones 1 Adjustable Glass Shelves 3 3 Storage Drawers 2 2 2 Removable Crisper Cover Removable Drawer Dividers 2
12. SPECIF S AND FEATURES Mos iF Model 611 Model 650 Refrigerator Freezer All Refrigerator All Freezer Over and Under Over and Under Overall Size H x W x D 73 x 36 x 24 73 x 36 x 24 84 x 30 x 24 84 x 36 x 24 Refrigerator Capacity 20 cu ft 12 7 cu ft 15 7 cu ft Freezer Capacity 19 3 cu ft 5 1 cu ft 6 3 cu ft Minimum Height Required 723 4 723 4 827 8 827 8 Door Swing Clearance 361 16 361 16 301 3 361 16 Specify Door Swing LH or RH e e Annual Energy Usage 58 76 61 68 Crated Shipping Weight O F Models 391 Ibs 378 Ibs 430 Ibs 482 Ibs Crated Shipping Weight S Models 420 Ibs 406 Ibs 462 Ibs 515 Ibs odel GOE Model 611 Model 650 Adjustable Glass Shelves Refrigerator 4 3 3 Stationary Glass Shelf Refrigerator High Humidity Compartment w Divider s Storage Drawers Refrigerator Adjustable Roll out Utility Basket Adjustable Door Shelves Refrigerator 2 1 1 Adjustable Gallon Door Shelf Refrigerator t t Adjustable Dairy Compartment Egg Container Automatic Ice Maker Adjustable Wire Shelves Freezer 3 Stationary Glass Shelf Freezer Storage Drawers Freezer 4 Two tier Pull out Freezer Drawer Adjustable Door Shelves Freezer 5 are based on 8 67 cents per kilowatt hour tGallon shelf is optional at n Model 601R Mod
13. all refrigerator model an all freezer model and an ice maker UNDERCOUNTER REFRIGERATION They all accept decorative door panels maximum 20 pound limit to fit any decor and can be built in to fit flush with virtually any base cabinet style or they can be installed a free standing units Equally important they are all backed by one of the best warranties in the industry These illustrations show the basic model configurations that the Sub Zero 200 Series offers For information regarding specific 200 Series models refer to the charts and illustrations in this section 24 24 24 24 18 E 1 pan 34 5 34 5 LL 114 Models Model 245 Model 249R Model 249RP 249FF 249FFI Model 506 Combination Combination All Refrigerator All Freezer Ice Maker ZOO SERIES SPECIFICATIONS AND FEATURES Specifications Model 245 Model 249R Model 249RP Model 249FF Refrigerator Freezer Combination Combination All Refrigerator All Freezer Overall Size H x W x D 34 x 237 8 24 3313 16 2378 24 3313 16 237 8 24 3313 16 237 8 24 Refriqerator Capacity 3 cu ft 4 4 cu ft 4 9 cu ft Freezer Capacity 1 9 cu ft 7 cu ft 4 6 cu ft Door Drawer Clearance 2513 16 25 253 253 Specify Door Swing LH or RH Annual Energy Usage 40 32 37 44 Shipping Weight 139 Ibs 120 Ibs 117 Ibs 135 Ibs Removable Shelves Stationary Shelves Do
14. application Sub Zero is offering you complete flexibility from the perspective of design applications stainless steel or you can apply your own different wood panels and storage capabilities You and your customer now have complete flexibility All our models have the flexibility built in from the factory You have the opportunity to apply the creativity In addition to the standard features listed below please make note of the following unique point Model 424 comes the overlay and stainless steel door panel configurations Models 427 and 427R are offered with the integrated and stainless steel options while Model 430 comes in the framed overlay and stainless steel options iDual Refrigeration System In a similar fashion to our 600 Series each 400 Series model has dual refrigera tion so your client will have specific individual tempera ture control of the two wine compartments Whether you storing wine or getting it ready to be served you have complete control and you know the precise temperature because of the digital readouts iElectronic Controls Sub Zero has added a micro processor to offer touch pad controls that are easy to understand and set the temperatures iDisplay Shelf This beautiful shelf offers your clients the opportunity to display those prize bottles of wine in their collection It is illuminated with discreet lighting mounted in the control panel iStorage Shelves The sturdy rustproo
15. inch Stainless Steel Handle 4 Illus 12 600 SERIES PLANI Side Panels When planning for side panels with the installation of the 600 Series unit you need to be aware of space configura tion to achieve a pleasing fit Depending on the exact panel you are using with your unit the height of the panel will vary Refer to illustration 13 for placement of cuts around the toe kick and grille area and remember that the dimension to the back of the main frame is237 s inches illus 13 Plumbing For units with an automatic ice maker rough in the water supply line Connect a 1 4 inch OD copper line to the house supply being sure to use an easily accessible shut off valve between the supply and the refrigerator Do not use self piercing valves A saddle valve kit part 4 20 088 0 is available from your distributor dealer A line filter is required when water conditions have a high sediment content The water line should be routed up through the floor with in 1 2 inch from the back wall and no higher than 3 inch es off the floor If you have to come through the wall make sure the water line is no more than 3 inches from the floor Regardless of the routing allow three feet of excess cop per tubing to remain outside the wall or floor for easy con nection to the unit Refer to illustration 1 and the Pre Installation Specifications chart on page 9 for exact spec ifications
16. left panel of the top drawer Contact a Sub Zero Factory Authorized Service Center a dealer or Sub Zero Freezer Company Customer Service Department P O Box 44130 Madison WI 54744 4130 call our Customer Service Department at 800 222 7820 or e mail us at customerservice subzero com 400 SERIE Sub Zero s newest addition to its complete line of residential refrigeration is wine storage equipment the 400 Series But it is more than just wine storage in the conventional sense It is wine storage as only Sub Zero could make it The ultimate in beauty engineering attention to detail and smart thinking will ensure this series is an instant success There are obviously right and wrong ways to store wine You will quickly see that Sub Zero is committed to the right way From the exterior and the smooth lines of the stainless steel to the ability to use wood on all the mod els each unit is beautiful The illustrations on the next page show the four basic con figurations offered Each model will be available in stain less steel and all of them will have the capability of hav ing wood panels applied to the doors and with the Model 427R you can also apply the wood to the drawers There are some subtle differences and it is important to understandthem 400 SER ES STORAGE All units will be shipped with glass doors as standard equipment Optional solid doors will be treated as special orders and must be ordered 90 d
17. standard 11 inch panel grille which will accept decorative panel inserts The traditional framed units will come with an elegant smooth full length handle and an 11 inch louvered grille All grilles are offered as options in one inch increments from 10 to 15 inches and be ordered as sales acces sories Model 650 F Framed SUB ZERO 600 SERIES An important step in assuring a successful plan is to make sure that the actual equipment shipped to your installa tion site matches the design you have ordered To ensure the best possible customer service make sure your installer checks the shipment carefully at the job site Each of these three design options Stainless Steel Framed and Overlay has specific installation require ments which means it is vital that the unit match your planning and space needs Each different design alterna tive will be shipped in a different carton Stainless steel units are packed in cartons with a gray cap and white lettering identifying them as stainless The stainless steel unit has a wrapped door one inch diameter handles and heavy duty stainless steel louvered grille iFramed units are packed in cartons with a white cap and blue lettering identifying them as framed The framed unit will have an extruded handle and louvered grille Overlay units are packed in cartons with blue cap and BUILT IN REFRIGERATION white lettering identifying them as overlay Units are s
18. to understand The integrated full panels or framed panels for glass doors will follow some of the identical planning processes you learned with the 700 Series The installation of the door panels is completely different however Rather than using the mounting hardware we used with the 700 Series door panels for both Models 427 and 427R will be applied with screws applied through our door The drawer panels for the Model 427R will be applied using the 700 Series technique of mounting brackets The installation instructions are covered in detail in books accompanying the individual units Please refer to illustrations 4 7 to give you a better idea of the exact space our unit needs and how the panels fit in relationship with the unit IMPORTANT NOTE While the stiles are a minimum of 2 1 4 for both the Models 427 and 427R the top and bottom rails of the units are different Rails and stiles can be increased in size but should not exceed cabinet manu facturers standard width They cannot exceed overall door panel dimensions specified as they would interfere with the operation of the door The back sides of rails and stiles that will be visible through the glass door will need to be finished Also the inside edges of the frames must be fin ished to match the front surface IMPORTANT NOTE The dimensions of these panels and stiles are assuming the models finish off at 80 in height overall and have a four inch toe kick for the Model 42
19. using some larger handle hardware you will also need LOCATE ELECTRICAL OUTLETWITHIN to take that into account SHADED AREA ilf installing a wine unit next to an existing Sub Zero unit you may have to allow for a filler strip and possibly a heater kit If you are connecting the unit to your home security sys tem you must allow a minimum of 36 inches of the sys tem s wiring to be routed in the electrical area designated AND 497 LOCATE ELECTRICAL for your respective model OUTIEEWITHN SHADED AREA MODELS 424 427 FRONT VIEW Illus 1 Pre Installation Specifications Finished Rough Opening A 24 27 27 2915 FinshedRoughOpenng B 34h 80 80 S3 Minimum Door Clearance C 253 251 2 2512 30 Maximum Door Swing D i 14700 105 105 7 130 Minimum Clearance 90 Door Swing E 2 2 T MEM 2 33 Minimum Clearance Maximum Door Swing 4 2277 35800 50 Minimum H Height Required ee SCZ Je 34 400 SERIES PLANNING INFORMATION Integrating Cabinetry All Units Unless you are installing a stainless steel unit you will need to provide a complete door panel in the instance of a solid door unit or a frame for the glass door application where wine will be seen from the outside If you order a stainless steel unit the Models 424 and 430 will be shipped with their panels and hardware installed and you
20. 01 F Models 611 and 650 GOIR 601F 611 W Refrigerator Panel 34 281 8 5815 16 48116 34 281 8 581546 183 8 241 32 B Handle Recess Location 1416 17116 Refrigerator Freezer Panel Models 561 642 and 632 INFORMATION IMPORTANT NOTE On all models except Models 680 and 690 routing recessing or optional extended handles may be required on raised panels for finger clearance under the handle Refer to the full scale illustrations in the center of this guide To install framed panels see the detailed procedures out lined in the Sub Zero 600 Series Installation Guide IMPORTANT NOTE The weight of each panel cannot exceed 50 pounds Panels thicker than 1 4 na Trim reveal Ya Panels 1 4 thick or less zm Trim reveal Ya min 1 Rout to 1 4 thickness 14 Panel Illus Illus 4 650 561 642 680 632 690 34 1918 24 16 27 he 20916 48 he 671146 671146 67 s 67 s 67e 34 1458 15 1213 16 1715 16 183 8 671186 671146 67116 24182 38582 385 82 a 257 32 Refrigerator Refrigerator Freezer Panel Panel Panel Trim Panels 05 thick d Models 680 and 690 600 SERIES PL INFORMATION Overlay Panels Overlay Panel Spacer Panel Spacer Panel The overlay design line allows decorative panels to cover the door trim for a more seamless appearance that b
21. 1 2 1 s T U sss ae Sean VEMM MUI OE T EN c Egg Container s er kilowatt hour Models 700BF 700BFI Models 700TC 700TCI 19 700 SERIES FE Features and Options Sub Zero s industry leadership is evident in this new approach to residential refrigeration Our tradition of excellence is evident in all of these features and options Functional Design These units can be placed any where in the home Think about point of use refrigera tion when planning where to place your units Kitchens can be laid out so no congestion occurs Built in Design All Sub Zero units are 24 deep These 700 Series units must have 5 8 inch minimum pan els that do not exceed a 40 pound weight limit for the door or 12 pounds for the drawer They will be compatible with virtually any cabinetry and be invisible when installed properly Microprocessor The brains of the 700 Series units this computer allows the best in temperature control effi ciency and food preservation Temperature Zones On the tall and base refrigera tor and combination units you have the flexibility of hav ing multiple temperatures within the same unit Adaptive Defrost Depending on the usage and the exact climate the 700 Series unit will adapt to the unique situation and adjust accordingly to offer greater efficiency Toe Plate Adjustable solid toe plate meets the stan dards of the Amer
22. 7 If you finish off at 84 for instances you MUST add four additional inches to the overall height of the panel and remember to add four inches to the top rail Likewise if you allow for a six inch toe kick for the Model 427 you must subtract two inches from the bottom rail NOTE The toe kick area on the Model 427 cannot be larg er than six inches Door panels for Models 427 and 427R can grow beyond the 80 inch height to accommodate any size of door as long as you stay below door panel weight limit of 20 pounds Refer to illustration 10 on page 26 of the 700 Series section for upper valance specifications 36 MODEL 427 OVERALL UL HB 686 lt 264 664 DOOR FRAME gt 14 356 E DIMENSION ale gt 2 S 0 32 131 337 Bee 9523 650 gt DRAWER FRONT el 101 260 208 517 344 877 E oy tt _ dI 70 103 1789 273 DOOR CENTERED FRAME fERTICALLY WITH HINGES E am Y k 8 227 Yo Y Y L0 FRONT VIEW Ka SIDE VIEW
23. CLOSED TOP VIEW FULL SCALE FRAMED CABINETRY LINE OF INTERFERENCE R OPENING AT MAXIMUM DOO cus Le SEE PAGE 24 FOR PATTERN DIMENSIONS SIDE MOLDING AND INSTALLATION HARDWARE PROVIDED BY SUB ZERO n 1 INSTALLATION OF TALL UNIT WITH ADJACENT CABINET 105 MAXIMUM DOOR OPENING TOP VIEW FULL SCALE FRAMELESS CABINETRY DASHED LINE INDICATES 90 DOOR OPENING AND ADJACENT SIDE PANEL AND COUNTERTOP lod SA PANEL E SUB ZERO DOOR COUNTERTOP 4 av H LINE OF INTERFERENCE
24. Model 424 Door Opening When planning to install the Model 424 next to adjoining cabinetry you must make provisions to allow the door to open to a maximum of 145 degrees and not hit the door panel Please refer to illustration 1 on page 34 35 103 273 CENTERED VERTICALLY 2 I 231 597 DOOR FRAME MODEL 424 OVERALL DIMENSIONS 23 606 23168 gt CABINET DIMENSION y X 1 30 RE 767 1244 DOOR FRAME Lu 3 FRONT VIEW 34 111 SIDE VIEW 3INCH ADJUSTMENT IN LEVELING LEGS MODEL 424 CABINETRY DIMENSIONS 606 lt 2332 DOOR PANEL 237 606 CABINET DIMENSION ELE 877 m 30 764 DOOR PANEL CENTERED VERTICALLY gt 3j FRONT VIEW 9 space SIDE VIEW 1 21NCH ADJUSTMENT IN LEVELING LEGS Illus 3 Door Panel W x Minimum Width of Rails and Stiles Door Panel Weiaht Limit Minimum Panel Thickness el Specifications 233 4 x 301 16 21 4 10 Ibs 5 8 H 400 SERIES PLANNING NFORMATION Models 427 and 427R Integrated Panels If you are familiar with the 700 Series and its panel appli cations this section will be relatively easy
25. NFORMATION SUB ZERO CABINET DOOR FRAMED CABINETRY BEADED INSET APPLICATION FRAMED CABINETRY COMMON APPLICATIONS TOP VIEWS 24 609 TO WALL SUB ZERO CABINET UNIT Em A NOTE SHADED AREA INDICATES STATIONARY STYLES AND RAILS TOP VIEW CABINET DOOR PANEL 222277774 Vie an ZZ 23 f b 222772722 KAAANMAASASASAY N N FRONT VIEW A ALL REVEALS ARE 1 4 INCH 6MM B DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS C BOTTOM RAIL MUST BE REMOVEABLE Illus 6 Framed Applications Framed cabinet applications present you with different questions to address Take the time to review the specifics of these illustrations as they will help form the basis for your design These are not meant to be the only alternatives but are suggestions from designers around the country Reveals between cabinets and the Sub Zero 700 Series units are 1 4 inch in all instances and drawer and door panels can vary based on information we supplied on ear lier pages 4 102 EXZ DIMENSIONS MAY VARY 24 TRADITIONAL FRAME FULL OVERLAY TO WALL SUB ZERO CABINET UNIT FRAME CABINET DOOR DOOR PANEL A TRADITIONAL FRAME STANDARD OVERLAY TO WALL SUB ZERO UNIT CABINET FRAME Ec
26. SUB ZERO FREEZER COMPANY DESIGN SOLUTIONS Welcome to Sub Zero We make the ultimate built in inte grated and undercounter refrigerators and freezers and we have added a complete line of wine storage units to our inventory Hidden refrigeration is an idea we invented it s an idea we continue to define For hundreds of design ers and hundreds of thousands of homeowners and now wine enthusiasts a home or kitchen is neither right nor complete without a Sub Zero We offer more solutions to your daily design problems of trying to work the largest appliance into a home without being obtrusive Placing refrigeration in the home is no longer a problem but an opportunity to exercise your cre ativity to place it where it logically belongs For instance instead of going to the refrigerator bring the refrigerator to your client with the 700 Series Our base and tall units enable you to place them in media rooms the workout room the master bedroom even beside the kitchen sink Sub Zero has rethought traditional built in refrigeration a category it pioneered with its 600 Series When our com plete line of configurations over and under side by side all refrigerator and all freezer are coupled with three design alternatives the results are that you have unlimit ed flexibility in satisfying your client s needs for residential refrigeration With the addition of the 400 Series of wine storage equip ment Sub Zero is breaking with
27. and 12 will give you a better idea of the panel construc tion and how it interacts with our frame Rails and stiles can be increased in size but should not exceed cabinet manufacturers standard width They can not exceed overall door panel dimensions specified as they would interfere with the operation of the door 204 Rail Stile spacer Panel L Overlay Panel Spacer Panel AC Door Grille Trim s Glass Illus 11 Illus 12 INFORMATION The back sides of rails and stiles that will be visible through the glass door will need to be finished Also the inside edges of the frames must be finished to match the front surface if you are using a solid door you would not order a frame but follow only the overall panel sizing of the framed and overlay applications As with all Sub Zero 600 Series equipment you have the flexibility of ordering larger panel grilles for either the framed or overlay applications For specific panel sizing on these optional grilles for either the framed or overlay applications of the Model 430 please refer to pages 12 and 13 of the 600 Series section of this Design Guide In addition side panel information for a Model 430 is available on page 14 of this Design Guide Wood Facing Wine Shelves Sub Zero has provided a natural cherry wood facing to each of its wine shelves in each model If however you would like to replace these strips with wood more com ple
28. arranty covers all parts and labor t repair or replace any part of the product which proves to be defective in materials or workmanship Limited 6th Through 12th Year Warranty From the through the 12th year from the date of original installation the Sub Zero warranty covers all parts that prove to be defective in materials or workmanship in the sealed system parts only The sealed system consists of the compressor condenser evaporator drier and all connecting tubing Terms Applicable Te Each Warranty All service provided by Sub Zero under the above warranty must be performed by authorized Sub Zero service representatives unless otherwise specified by Sub Zero Service will be provided the horme during the normal business hours This warranty applies only te products installed for normal residential use Details regarding non residential warranty are available upon request The warranty applies only to products installed amy one of the fifty states of the United States the District of Columbia or the ten provinces of Canada This warranty does cover any parts or labor te correct any defect caused by negligence accident or improper use maintenance installation service or repair including but net limited ta improper removal and reinstallation whether in the unit at a remote location of the condensing unit The remedies described above for each warranty are the only ones which Sub Zero will provide ei
29. ars to come Serwice For Sub Zero Refrigeration Systems If your client needs service advise them to check the model and serial number on the plate at the top frame of the unit inside the door Contact a Sub Zero Factory Authorized Service Center a dealer or Sub Zero Freezer Co Service Department P 0 Box 44130 Madison WI 53744 4130 call 800 222 7820 or e mail us at customerservice subzero com SUB ZERO 700 SERIES Creating Solutions for Home Refrigeration Needs You would expect it from the best A refrigeration system that is responsive to the unique needs of your situations and can adapt to any of your demands The 700 Series of integrated refrigeration from Sub Zero ushers in a new era of refrigeration that can be placed at its point of use and not take away from the overall pleas ing design of the room Instead of going to the refrigerator bring the refrigerator to you In the workout room next to the home entertain ment center in the master bedroom even beside the kitchen sink The 700 Series becomes totally invisible parts of the beautiful home and then they become absolutely essential parts of the family All Sub Zero 700 Series models are 27 inches wide We make a tall refrigerator a tall freezer and a tall refrigera r car RATED REFRIGERATION tor freezer We also make a two drawer refrigerator and a two drawer freezer You just need to add whatever beau tiful cabinetry you want to u
30. ays before you expect delivery Stainless steel units will be shipped with tubular stain less steel handles while the overlay units will come with no handle hardware The framed Model 430 will come with an extruded handle identical in design to our 600 Series look Optional handles are available for all models and you should consult your Sub Zero distributor for descriptions and prices iStandard grille assemblies for the Model 430 will be provided in one inch increments from 10 to 15 inches The standard height will be 11 inches The framed unit will have a louvered grille the stainless steel unit will feature a heavy duty louvered grille and the overlay model will have the panel grille which accepts decorative panel inserts SERIES As with all Sub Zero units the 400 Series is manufactured to the exacting quality standards which has made us the leader of the refrigeration industry Because the 400 Series comes with everything you need to ensure your cus tomer s wine is stored properly and safely there are only a few options They are listed on the following pages The following features are common to all 400 Series models f Twodistinct temperature zones e Electronic control panel with microprocessor e Ideal humidity environment e Roller glide shelves Model 424 Model 427 Undercounter All Wine Storage All Wine Storage STORAGE Storage for standard bottles half bottles and magnums Rust p
31. bracket been installed properly L Arethe panels installed properly O Isthe unit operating If not is unit plugged in Check to see if unit is operating before you install Have the temperatures been set Is packing material removed O Is toe plate grille installed O Does the customer understand the unit s operation L Does your customer understand Sub Zero s 12 Year Protection Plan warranty When you ve completed this final check you can be assured that your client will enjoy the very best in home refrigeration for years to come Service For Sub Zero Wine Storage Equipment If your client needs service advise them to check the model and serial number on the plate attached to the underside of the control panel divider wall underside of the top wall for Model 424 of the appliance Contact a Sub Zero Factory Authorized Service Center a dealer or Sub Zero Freezer Co Service Department P 0 Box 44130 Madison WI 53744 4130 call 800 222 7820 or e mail us at customerservice subzero com SUB ZERO 200 SERIES Undercounter Refrigeration of Exceptional Quality Aside from the full size units Sub Zero offers in its 600 and 700 Series lines of refrigeration we round out our product line up with a line of traditional undercounter refrigeration which meets all of the exacting standards you have grown to expect from Sub Zero Our undercounter line consists of two different refrigera tor freezer combinations an
32. conventional ways of offering wine storage for designers and their clients Now you are not just limited to placing an undercounter unit with a stainless steel look you have the ability to add a wood frame to the unit or for a customer who is really a wine enthusiast you have the ability to choose from four differentmodels We also offer undercounter refrigerators of exceptional quality There are different configurations to satisfy any needs In all instances you can depend on Sub Zero Our reputa tion is legendary We have engineered and manufactured the best product and warranty in the business and today we stand behind our product like no one else Each one of our units is tested before it leaves our factories and if ser vice is necessary there is a network of thousands of facto ry trained technicians to help you Each unit is protected by the Sub Zero 12 Year Protection Plan that covers the entire unit for two years for parts and labor from the date of installation A five year parts and labor warranty and a six through twelve year parts war ranty covers the sealed system including compressors con denser evaporator drier and all connecting tubing Review the changes we have made to Sub Zero to help you solve your design problems We are confident you will like what you see because in many instances these are changes you have been asking for IMPORTANT NOTE As you follow these instructions you will notice warning a
33. dard for all models Illus 5 IMPORTANT NOTE The weight of each panel assembly cannot exceed 50 pounds Overlay Panel Specifications TR Godr en w Refrigerator Overlay Panel 34746 28716 34716 24546 Refigerator Overlay Panel n e QUE MEC CMM T T ME r MMC MEC M UR Os EE uem TEE w Refrigerator Spacer Panel 331 2 275 33 5 233 8 271h6 xb DEDE Ped ee i ue W Freezer Spacer Panel 38 C 2 mare pgp ee T 25 mE w Refrigerator Backer Panel 341 8 281 8 341 3 24 2711 6 T naires Panel MEZ NEES sms w lem Su fond REX oe en ime oa To E lege U So 7 600 SERIES PLANN Overlay Grille Panels Overlay grille panels match the design look of the door panels This option is available on 600 Series Models 611 650 642 680 632 and 690 Keep in mind that the over lay panel design option is not available on Model 680 and 690 doors however the overlay grille panel is optional on the framed application for these models Refer to the Overlay Grille Panel Specifications chart and illustration 8 for panel specifics a Overlay Grille Panel H 4 Models 611 650 642 680 632 and 690 Hlus 8 A CAUTION Do not exceed the panel dimensions listed for the appropriate overlay grille panel y
34. el 601F Model 611 Model 650 Note All units are shown with louvered grille which are standard on framed units 6 Model 561 600 SERIES SPECIFICATIONS AND FEATURES Model 561 Model 642 Model 680 Model 632 Model 690 Side by Side Side by Side Ice 8 Water through door Side by Side Ice amp Water through door 84 x 36 x 24 84 x 42 x 24 84 x 42 x 24 84 x 48 x 24 84 x 48 x 24 12 5 cu ft 16 cu ft 15 2 cu ft 18 8 cu ft 18 2 cu ft 8 9 cu ft 9 5 cu ft 9 5 cu ft 11 3cu ft 11 2 cu ft 827 8 827 8 827 8 827 8 827 8 203 4 259 16 259 16 291 4 291 4 70 75 88 81 96 500 Ibs 541 Ibs 569 165 582 lbs 610 Ibs 538 Ibs 582 Ibs 608 Ibs 630 Ibs 656 Ibs 3 2 e e LED Dessus qut Se eee Model 642 Model 680 Model 632 Model 690 600 SERIES F E Features and Options Sub Zero s design beauty and quality are reflected in the broad range of standard features that put Sub Zero in a class by itself Whether your customer prefers stainless steel traditional framed or overlay design Sub Zero s 600 Series has the most design options to complement your installation The custom design appearance of the Sub Zero 600 Series gives it unique consumer appeal and gives you options no other line offers In addition Sub Zero units give you and your customer all these features iNew overlay
35. el grille as standard equipment You will need to order a panel for the grille and hardware to complement your surrounding cabinetry While the overlay panel design offers you a more seamless appearance you need to be aware of adjacent cabinets i e andlor countertops when the door is opened Refer to 4A 4 illustrations B and C in the center of this guide FRONT VIEW 198 SPACE SIDE VIEW 2INCH ADJUSTMENT IN LEVELING LEGS 10 38 400 SERIES PL Overlay Panel Specifications Model 430 Overlay Door Panel W x H 287 16 68 Spacer Panel W x H 2715 x 67116 Backer Panel W x 281 8 x 6711 16 Minimum Width of Rails and Stiles 21 4 Door Panel Weight Limit 25 Ibs Minimum Panel Thickness 3 8 Grille Panel Specifications Model 430 Overlay Grille Panel W x H Spacer Panel W xH 2712 x 95 16 Backer Panel WxH 281 8 x 9 5 16 Grille Panel Weight Limit 15 Ibs 28716 101 4 Minimum Panel Thickness 5 To achieve the overlay look you need three different pan els the decorative overlay panel 1 spacer panel and a1 4 inch backer panel Depending on your cabinet manufacturer this could be one panel routed for different dimensions or more likely three different panels Refer to the Overlay Panel Specifications charts for complete details on the overlay sizing In addition illustrations 11
36. enser indicator light iNew Shelf A one gallon storage door shelf is stan dard and affords convenient door storage for those large containers The Models 650 and 611 offer the gallon shelf as an option at no cost to the consumer Call Sub Zero at 800 222 7820 for specifics iDrip Proof Shelves Cantilevered shelves make repositioning quick and easy They re easy to clean and drip proof They are steel reinforced to provide durability and reliability Dairy Storage Dairy compartment is adjustable with easy one door access compartment dividers and a clean design The dairy shelf is magnetically sealed to maintain freshness iAutomatic Ice Ice maker provides high quality cres cent shaped ice that won t stick to the side of the glass iBuilt in Look Shallow depth design means access is easy to any area of the refrigerator iAdjustable In door shelves are all adjustable for complete flexibility iTight Seal Magnetic gaskets around all doors give extra tight seals iEnergy Efficient Our solid core doors improve insu lation and structural integrity iToe Plate Solid adjustable toe plate gives a true built in look and conforms to American Institute of Architects standards 600 SERIES PLZ INFORMATION Planning Information PRE INSTALLATION SPECIFICATIONS Although the 600 Series offers a wide range of designs and configurations the basic planning considerations for all models have much in common As you in
37. f wire shelves can easily accommodate standard 750 ml bottles half bot tles as well as magnums All the shelves are finished off with a natural cherry wood facing for a beautiful elegant look In addition all shelves will enable you to be sure the wine is stored properly and that the corks are in contact with the bottles contents iRoller Assembly All shelves have a roller assembly which enables you to have a three quarter extension for easy access to all bottles of stored wine SAND OPTIONS iService Alert An indicator light will let you know if service may be necessary in addition you have the option of hooking the equipment up to your home security sys tem iDiscreet Lighting Our soft lighting is independent of door opening iCorrect Temperatures The temperature range of each wine compartment is 38 degrees to 65 degrees Fahrenheit and your set temperature is digitally displayed in the control panel iHumidity Proper humidity is maintained throughout the entire unit Protection tinted glass minimizes the amount of ultraviolet light entering the unit iLock A lock will be offered as an option for all 400 Series models The lock is offered as a sales accessory and should be ordered through your Sub Zero product distribu tor Solid Doors If you would like to order a unit without glass you have that option also This will be treated as a special order and you have to let Sub Zero know 90 day
38. hipped with no handle hardware hardware is supplied at the site to match cabinetry at the installation anda two part panel grille frame without a panel At the end of this section you ll find a checklist for installing Sub Zero 600 Series units This checklist is intended as a brief summary of the most important proce dures involved in installation However they do not con stitute detailed installation instructions Comprehensive installation instructions are shipped with each unit Refer to those instructions in preparing and installing all Sub Zero products or call Sub Zero Freezer Company at 800 222 7820 for your copy The GOO Series For information regarding specific 600 Series models refer to the charts and illustrations in this section Regardless of the specific design application all interior specifications are identical 36 4 H 36 Model 601 R All Refrigerator Model 601 F All Freezer k 42 4 k 42 1 ll prece 1 Model 611 Model 650 Model 561 Model 642 VUA CAM Model 632 baa e Over Under Over Under Side by Side Side by Side Side by Side through the Door through the Door 600 SERIES
39. ican Institute of Architects Inset area for a solid decorative toe plate is 4 inches high by 3 inches deep You can show a 10 inch toe plate but you cannot cover the louvers in this area If you choose the louvered grille can be painted Front Venting All units have the mechanical equip ment in an area below the lower drawer The lower draw er panel can extend to cover these louvers but a decora tive toe plate cannot cover the fins A decorative toe plate can be placed over the lower 4 inch area but it must be removable for cleaning and service Halogen Lighting A bright white light offers even illumination throughout the entire unit Door Drawer Alarm If your door or drawer is acci dentally left open for more than 15 seconds an audible alarm will sound You can easily disarm this feature when you are cleaning the unit or adding groceries Drip Proof Shelves All shelves in the cabinet sec tions of the tall units feature totally adjustable drip proof S E ms AND OPTIONS one piece glass shelves that are easily removed for clean ing or repositioning Dairy Shelf This magnetically sealed compartment is fully adjustable on the tall refrigerator and combination unit for small items that need a fresh environment Crisper Cover On the tall and base refrigerator units a removable crisper cover is offered for one of the drawer sections On the combination unit the crisper is attached to
40. imum Width of Top Rail 35 8 Width of Bottom Rail 8 Minimum Width of Stiles 21 4 Door Panel Weight Limit 20 Ibs Minimum Panel Thickness 5 8 Please note on the left hand side of the overall unit dimensions where we have located pre drilled holes for our optional handle hardware Refer to page 39 for specifics about installing handle hardware Drawer Panel Specifications Model 427R Only IMPORTANT NOTE In the following chart the bottom drawer panel height is based on a 4 toe kick If you want to show a 6 toe kick you must subtract two inches from the bottom drawer panel height 265 8 x 451 4 Door Panel W x H Minimum Width of Top Rail 35 8 Minimum Width of Bottom Rail ch Minimum Width of Stiles 21 Door Panel Weight Limit 20 lbs Top Drawer Panel W x Bottom Drawer Panel W x H 26 x 137 16 265 8 x 169 16 12 lbs each Minimum Panel Thickness 5 8 Drawer Panel Weight Limit Model 430 Framed and Overlay Panels The framed and overlay treatments of panels for the Model 430 are identical to the Model 611 in width and the 632 in height you will need to be aware of some of flexi bility and limitations these issues give you 400 SERIES PLANNING INFORMATION 430 nel Mode Framed Panels MODEL 43 OVERALL DIMENSIONS Unlike the Model 611 you cannot use a 1 4 panel for a f h esie covering of the glass door It is fine when applying a panel Ee ee DOOR
41. inches to ensure a consistent 1 4 inch reveal Illus 9 INSTALLATION WITHOUT SIDE PANELS CABINETS 24 ig 609 I B TOP VIEW PANEL WIDTH DIMENSIONS SINGLE UNIT 16 REVEAL INSTALLATION WITH SIDE PANELS 25 657 APPLIANCE CABINETRY CABINETRY OR SIDE 9 DOOR WIDTH OR SIDE PANEL PANEL MINIMUM SIDE PANELS I SUB ZERO UNIT TWO UNITS SIDE BY SIDE 54 1372 5 ie di 268 677 26 em jd ie REVEAL 4 REVEAL REVEAL CABINETS 9 PANEL 9 PANEL 54 1372 CABINETRY CABINETRY TOPVIEW OR SIDE OR SIDE PANEL PANEL THESE DIMENSIONS MAY VARY DEPENDING ON INSTALLATION AT END OF RUN CABINET STYLES TREAT MENT OF COUNTERTOPS SUB ZERO SUB ZERO OR OTHER DESIGN UNIT UNIT OPTIONS Illus 8 MINIMUM SIDE PANELS e 700 SERIES PLZ INFORMATION Door Panel Helght UPPER VALANCE DETAIL Door panels can grow beyond the 80 inch uni height to accommodate any size of door as long i 609 A as you stay below the recommended door panel ANY DECORATIVE VALANCE weight limit of 40 pounds THE FRONT OF THIS PLANE Illustration 10 shows how the panel may grow CHECK CENTER SPREAD OF THIS MANUAL FOR and what you need to consider doing to finish the area in back of the door panel PANEL EXCEEDING a HIGH IMPORTANT NOTE The valance you use to finish
42. l width along with the grille height and you will have the panel size Hardware Considerations The handle hardware must be installed before installing the panel assembly Use larger D style pulls If screws with thick heads are used the screws will need to countersunk into the door before the panel is put into place IMPORTANT NOTE Sub Zero does not recommend using single pull knobs on any of its 600 Series units If your customer has chosen overlay decorative door and grille panels the unit will be shipped without handle hard ware You or the cabinet manufacturer must provide han dle hardware at the job site to match the overall decorat ing scheme 13 113 16 123 16 However you can order handles from Sub Zero as option al features These handles incorporate the craftsmanship and attention to detail for which Sub Zero is famous Optional handles are available in the following designs and configurations 18 inch antique brass handles 18 inch polished brass handles 18 inch polished chrome handles 1 inch diameter by 24 inch long stainless steel handles Refer to illustration 11 for mounting specifications of the 18 inch handles listed above and see illustration 12 for mounting specifications of the 24 inch stainless steel handles 103 4 18 zl il End View 18 inch Antique Brass Polished Brass and Polished Chrome Handle 35g m Illus 11 165 16 245 16 24
43. lends with the design of the room To achieve this look the most common way is to work with three panels the decora tive overlay panel a 10 inch spacer panel and a 1 4 inch backer panel Depending on your cabinet manufacturer this could be one panel routed for different dimensions or Door Drawer more likely three different panels Grille Trim 7 a oN N m The overlay panel design option is available on all 600 Series units except Models 561 680 and 690 Illus 7 Keep in mind that the Sub Zero door panels have the potential for hitting adjacent cabinets and or countertops when they are opened You need to be aware of your sur rounding cabinetry and space limitations when using the overlay units Refer to full scale illustrations B and C in the center of this guide w Regardless of the physical construction of the panels Refrigerator routing or three panel assembly you will need to follow this chart and illustration 5 for exact sizing and panel placement to ensure a proper fit Eh 4 T Illustration 6 is a cross section view of the three panel assembly showing placement of the door drawer grille i trim Models Models Model Illustration 7 shows a rear view of the three panel assem SOAR and 611 650 642 632 bly and critical dimensions stan
44. llowing designs andconfigurations 118 inch antique brass handles 118 polished brass handles 18 inch polished chrome handles 18 inch stainless steel handles Refer to illustration 13 for mounting specifications I End View 18 inch Antique Brass Polished Brass and Polished Chrome Handle 103 4 5 gt lt End View 103 4 18 18 inch Stainless Steel Handle 35 8 lt 13 Electrical A 115 volt 60 Hz 15 amp fused electrical supply is required It is recommended that a separate circuit serving only this appliance be provided All Sub Zero 400 Series units are equipped with a power supply cord with a 3 prong grounding plug and it must be plugged into a mating 3 prong grounding type wall recep tacle Follow the National Electrical Code and local codes and ordinances when installing the receptacle Refer to illustration 1 page 34 for exact specifications 40 INFORMATION Checking The Results The 400 Series Installation Guide packed with the appli ance will give you step by step procedures for making sure the unit is installed properly The following is a checklist of some of the important items you ll want to review before your installation is complete Following these guidelines will assure a beautiful and safe installation and a satisfied client Has blocking been completed or the anti tip blocking
45. mentary to your design and surrounding cabinetry you can Illustration H is a full size template provided in the center section of this Design Guide you mustfollow the layout of this format to accommodate the shelves properly To remove the cherry strips take the shelves out and merely remove the screws Reverse the procedure to affix the new wood If you choose to stain or seal the wood facing be aware that some of these substances are hazardous and will damage stored wine Handle Hardware Considerations With the Model 424 overlay Models 427 and 427R inte grated and Model 430 overlay you must supply your own handle hardware It is recommended you use our optional handles and use the pre drilled holes supplied to locate the handles within the frame of our unit This will allow you to provide the best possible handle alignment and not take away from the strength of the stile in this area after the unit is used a number of times 400 SERIES PLANI If you elect to place different hardware on these units we encourage you to fasten the hardware by passing through our door and attach the hardware through the Sub Zero door s frame A CAUTION When planning for hardware please refer to illustra tion G in the center section of this guide to give you a better understanding of the unit s frame and position ing of the glass for the door You must not drill through this glass Optional handles are available in the fo
46. models blend seamlessly into your overall room design and complement surrounding cabinetry Your job is made easier and more creative iStainless steel models feature new wrapped doors one inch diameter stainless steel handles and stainless steel grille designed specifically to enhance the aesthetics of the professional look of kitchens today iClassic framed models the look that made Sub Zero famous now feature an improved grille design new han dle design and elegant new hinges iDual Refrigeration System All 600 Series combi nation units have the exclusive Sub Zero dual refrigeration system which ensures the freshest food and energy effi ciency at the same time You have precise independent control of the refrigerator and freezer compartments e Fresh Food High humidity compartment is large and deep with smooth sides for easy cleaning The compart ment features removable dividers iDigital Controls Controls are up front and easy to use They give your customer digital readings for quick easy to read reference Up front controls also keep your client informed about the operation of the unit on a con tinuous basis AND OPTIONS ilmproved Lighting Bright lighting spreads even illumination throughout the compartment and conceals the source iElectronic Controls Sub Zero s added a micropro cessor to give you better control automatic defrosting that senses then adapts to your use patterns and a vacuum cond
47. mum Door Clearance at 90 25346 Minimum Height Required 34 Recommended Electrical Outlet Location D 1 Recommended Electrical Outlet Location E 2 Water Supply Location F 12 PRE INSTALLATION SPECIFICATIONS TOP VIEW LOCATE ELECTRICAL OUTLETWITHIN SHADED AREA FRONT VIEW TOP VIEW DOOR SWING CLEARANCE 1 249R 24 347 25 3414 1070 gu N A 249RP 249FF 24 3412 253 8 3414 1012 8 24 34 253 8 344 1015 21 N A 249FFI 24 3412 253 8 3414 1015 21 18 506 18 34 1134 3414 21 21 11 200 SERIES PLANNING INFORMATION Integrating Cabinetry The Door Panel Specifications chart and illustration 2 pro vide necessary panel sizing information w v A Door Panel been Lower Panel H 4 Model 506 Illus 2 MOdels 245 249R 249RP 249FF and 249FFI Door panels must be 1 4 inch thick around the perimeter If the panel is thicker than 1 4 inch an edge must be rout ed around the panel to ensure a proper fit Model 245 is the exception While the edge must be 1 4 inch thick you must allow 3 8 inch around the perimeter for the frame See illustrations 3 and 4 Panels 1 4 thick or less Panels thicker than 1 4 3 Trim reveal yar min F Trim reveal 1 4 min Rout to 1 4 thickness Panel
48. nd caution symbols This blocked information is important for the safe and efficient installa tion of this Sub Zero There are two types of potential haz ards that may occur during this installation CAUTION signals a situation where minor injury or product dam age may occur if you do not follow instructions A WARNING states a hazard may cause serious injury or death if precautions are not followed Another footnote we would like to identify is IMPORTANT NOTE This highlights information that is especially relevant to aproblem free installation TABLE OF CONTENTS Sub Zero 600 Series 600 Series Built In Refrigeration 4 5 ModelSpecificationsandFeatures 6 7 Features and Options 8 Planninglnformation 9 14 Sub Zero 700 Series 700 Series integrated Refrigeration 17 ModelSpecificationsandFeatures 18 19 Features and Options 20 Planninglnformation 21 28 Sub Zero 400 Series 400 Series Wine 30 31 Model Specifications and Features 32 Features and Options 33 Planninglnformation 34 40 Sub Zero 200 Series 200 Series Undercounter Refrigeration 43 ModelSpecificationsandFeatures 44 45 Planninglnformation
49. one of the adjustable shelf assemblies Deli Drawer Smaller items are not lost in this handy feature of the tall refrigerator unit Egg Tray You can easily store a dozen eggs on this removable egg tray that is offered on the tall refrigerator and combination units Ice Maker An automatic ice maker providing crescent shaped ice is available as an option on the tall and base freezers as well as the tall combination unit This optional equipment must be factory installed Automatic Defrost All Sub Zero 700 Series units have an automatic defrost system Door Swing You can choose left or right door swing on the tall units This option must be ordered when requesting the unit You cannot reverse the door in the field Door Stop On all of the tall units a 90 degree door stop is built in to the patented hinge of this unique pro duct Normal door swing is 105 degrees Temperature Zones With the microprocessor in the 700 Series units you have the capability of setting tem peratures to ensure food is stored at its optimum level Different foods enjoy different temperatures and humidity levels and with the 700 Series food storage system you have the ability to set different temperatures The micro processor will read the temperature in each zone every second and make any necessary adjustments Temperature zones and optimum ranges for all units 700TR Three Zones 34 to 45 degrees I e 700BR Two Zones
50. onnection to the unit IMPORTANT NOTE Do not route water supply line in front of compressor tray The tray must be slid forward for service 700 SERIES INFORMATION SERIES Checking the Results The Installation Guide packed with the appliance will give you step by step procedures for making sure the unit is installed properly The following is a checklist of some of the important items you ll want to review before your installation is complete Following these guidelines will assure a beautiful and safe installation and a satisfied client O Has the anti tip blocking bracket been installed prop erly and is it making contact with the unit Are the panels installed properly L1 Is the unit operating If not is unit plugged in Check to see if unit is operating before you install Ll Have the temperatures been set L Is packing material removed 4 Is water supply line connected to the units where ice maker is in place Is toe kick grille installed n n Does the customer understand the unit s operation Does your customer understand Sub Zero s 12 Year Protection Plan warranty When you ve completed this final check you can be assured that your client will enjoy the very best in home refrigeration for years to come 28 Service for Sub Zero Refrigeration Systems If your client needs service advise them to check the model and serial number on the plate installed to the inside
51. or Shelves Automatic Ice Maker Automatic Defrost Model 245 _ Model 249R 2 2 I I Model 249R Model 249FF 2 1 Model 249RP 200 SERIES SPECIFICATIONS AND FEATURES Specifications Model 249FFI Model Refrigerator Freezer Overall Size x W x D Refrigerator Capacity Freezer Capacity Door Drawer Clearance Specify Door Swing LH or RH Annual Energy Usage Shipping Weight All Freezer 3313 16 237 8 x 24 4 6 cu ft 253 8 44 135 Ibs Ice Maker 3413 32 x 177 a x 237 8 113 4 Interior Features Removable Shelves Stationary Shelves Door Shelves Automatic Ice Maker Automatic Defrost ee Model 249FFI 2 energy costs are based on 8 67 cents per kilowatt hour Model 506 Models 249 249 Model 506 as 200 SERIES PLANNING INFORMATION Planning Information All 200 Series undercounter units require the same basic planning considerations before installing Review the installation requirements for your particular unit These charts and illustrations provide planning information for all Sub Zero 200 Series models Refer to the Pre Installation Specifications chart for impor tant information regarding area requirements minimum door clearance electrical and plumbing placement Pre Installation Specifications Model 245 Finished Rough Opening A 24 Finished Rough Opening B Mini
52. ou are specifying The overlay decorative panel cannot be any larger or it may restrict the air flow to the compressor area and cause problems with the operation of the Sub Zero unit Models 611 and 650 Reveal Option For Models 611 and 650 you may want to minimize the reveal between the bottom of the overlay door panel and the top of the overlay drawer panel In this instance follow the dimensions for the standard backer and spacer panel in the Overlay Panel Specifications chart The overlay panel height on the door grows by 1 2 inch See illustration 9 Overlay Grille Panel Specifications INFORMATION Model 611 Overlay Refrigerator Door Panel 287 16 w x 483 4 h Overlay Freezer Drawer Panel 287 16 w 18 t 16 h Model 650 Overlay Refrigerator Door Panel 347 16 w x 483 4 h Overlay Freezer Drawer Panel 347 16 w 1 81116 With this option you must route a space for the unit s hinge plate so it does not strike the door panel Refer to illustration 10 Panel grille sizes remain as specified in the Overlay Grille Panel Specifications chart Bottom Edge Hinge Side rearview Illus 9 Illus 10 A CAUTION Do not exceed the overlay decorative panel dimen sions listed for the Models 611 or 650 in the standard or optional charts If you try to make the reveal tighter between the door and drawer panels the panels may hit when opening and closing causing possible dam age to the panels and the S
53. pecifics on door openings and filler size alternatives Illus 1 Pre Enstallationm Specifications Finished Rough Opening A 3515 3515 Finished Rough Opening B 7234 723 4 8334 833 4 8334 833 4 833 4 Minimum Door Clearance at 90 C 36 6 36 6 30 2034 25946 25946 2914 2914 Minimum Height Required levelers 723 4 723 4 8278 827 827 8278 8278 25 NA UO Mar cT MERC Sar MM ds 600 SERIES PL Integrating Cabinetry In your plan for panels be sure you are working with the Sub Zero panel design family called for in your design If your customer has chosen the stainless steel design the unit will be shipped complete with wrapped stainless steel doors and handle hardware You will not have to install panels If you and your client have ordered either framed or over lay design models you will be adding panels to give the unit the custom Sub Zero look Be sure to keep the follow ing details in mind If the thickness of the custom panels is less than 1 4 inch they must be backed up with a sheet of shim material to build the total thickness to 1 4 inch If the panel is thicker than 1 4 inch an edge must be routed around the panel to ensure a proper fit See illustrations 3 and 4 Framed Panel Specifications Model H Refrigerator Panel A Handle Recess Location 2915 32 2915 32 Illus 2 w Door Panel 1 Models 601 R and 6
54. right of the thinner blades The outlet must be flush with the back wall Refer to illustration 1 on page 21 for exact placement A WARNING All Sub Zero 700 Series units are equipped with a 3 prong grounding plug and they must be plugged into a mating 3 prong grounding type wall receptacle Do not use an extension cord or two prong adapter Electrical ground is required on this appliance Do not under any circumstances remove the power supply cord ground prong 27 G INFORMATION For units with an automatic ice maker rough in the water supply line Connect a 1 4 inch OD copper line to the house supply being sure to use an easily accessible shut off valve between the supply and the refrigerator This shut off valve should not be installed behind the unit Do not use self piercing valves A saddle valve part 4 20 088 0 is available from your distributor dealer A line fil ter is required when the water supply has a high mineral content Illustration 1 on page 21 shows the water line s precise placement When routing the water through the side walls you must place the water line within 1 2 inch of the floor and as close as possible to the back wall The line must be routed around the anti tip bracket so it clears the bracket and the leveling feet of the unit Refer to the top view in illustration 1 Regardless of the routing allow for 27 inches of excess copper tubing to remain outside the wall or floor for easy c
55. roof wire shelves with wood facing e llluminated display shelf except Model 424 e Discreetinterior lighting e Service indicator and home security tie in UV resistant glass protection e Divider gasket to ensure separate temperatures e Front venting These illustrations show the basic model configuratio that the Sub Zero 400 Series offer Model 427R Model 430 Wine Storage with All Wine Storage Refrigeration Draw ers 400 SERIES SPECI S AND FEATURES Sen WOES Overall Size H x W x D 341 2 x 237 8 x 24 80x 2 x 24 80 x 27 x 24 Wine Storage Capacity 750 ml bottles 46 bottles 132 bottles 78 bottles Refrigerator Capacity 5 cu ft Door Swing Clearance 253 8 251 2 251 2 301 8 Specify Door Swing LH or RH Crated Shipping Weight 190 Ibs 395 Ibs 410 Ibs 435 Ibs Crated Shipping Weight Stainless Steel 195 Ibs N A N A 445 ibs Crated Shipping Weight Solid Door 0 185lbs 386 lbs 406lbs 4i2ibs Distinct Temperature Zones pperCompartmentShelves Lower Compartment Shelves Display Shelf Botiles Per Standard Shelf 750 ml bottles 8 9 9 IO Optional Door Lock I n Model 424 Model 427 Model 427R Model 430 400 SERIES FF Features and Options When looking at wine storage units you no longer have to think only about a unit that may fit in an undercounter
56. s before you need the unit iBuilt in Look Sub Zero offers you and your clients a host of design alternatives to choose from when choosing the look you want Wood or stainless steel framed over lay or integrated The choices are in your hands ilight Seal Magnetic gaskets around the doors give extra tight seals Plate Solid adjustable toe plate gives a true built in look and conforms to American Institute of Architects standards iFront Venting All Sub Zero wine storage units are designed for mechanical system air flow at the front of the appliance Decorative panels must not cover louvered sur faces or prevent removal of louvered components iSub Zero Protection Plan Like all Sub Zero units the 400 Series is covered by the Sub Zero Protection Plan 400 SERIES PLA INFORMATION SERIE Planning Information PRE INSTALLATION SPECIFICATIONS Review the installation requirements for your particular unit in illustration 1 and the Pre Installation Specifications chart They cover all the details you need to know about space allocation and placement of electrical whether the units are framed overlay stainless steel or integrated A The units must be installed to open a minimum of 90 TOP VIEW degrees or you will have problems pulling the shelves out iFor corner installations you need allow for a minimum two inch filler so the door can open to 90 degrees If you lt TOP VIEW y MODEL 430 are
57. se This Design Guide is intended to offer you a profile of our 700 Series units and what it takes to plan them into a home At the end of this section you ll find a checklist for installing Sub Zero 700 Series units This checklist is intended as a brief summary of the most important proce dures involved in installation However they do not con stitute detailed installation instructions Comprehensive installation instructions are shipped with each unit Refer to those instructions in preparing and installing your units or call Sub Zero Freezer Company at 800 222 7820 for your copy For information regarding specific 700 Series models refer to the charts and illustrations in this section ii Model 700TR Model 700BR All Refrigerator All Refrigerator a 27m 2 iw Models Models Models 700 700 700BF 700BFI 700TC 700TCI All Freezer All Freezer Combination 700 SERIES SPECIFICATIONS AND FEATURES Specifications Medel 700TR Model 700BR Model 700TF Model 700TFI Refrigerator Freezer All Refrigerator All Refrigerator All Freezer All Freezer i Conn e x 2 5 ex Um 2 25 a a 105 Mm a E Freezer Capacity 15 2 cu ft 15 2 cu ft Door Drawer Clearance 251 2 191 2 251 2 pom Hoa casei ead aia iia YU sasa pay em ENS mo 525 ae _ Shipping Weight 360 Ibs 190 Ibs 7 360lbs 360 Ibs rior Features
58. tegrate Sub Zero units into your overall plan review installation require A sit VANE ments for your particular units Illustration 1 and the Pre Installation Specifications chart provide planning informa tion for all Sub Zero 600 Series units framed overlay and stainless steel Allow units to open a minimum of 90 degrees or you ll TOP VIEW have problems removing drawers With the door opening 90 degrees have to move drawers slightly to clear 642 680 632 AND 690 vom LOCATE ELECTRICAL the door interior Refer to the minimum door clearances in OUTLET WITHIN TOP SHADED AREA the Pre Installation Specifications chart For corner installations allow for a minimum two inch filler so that the door can open to 90 degrees If you re using raised panels consider using a wider filler C s MODELS 601R AND 601F When units are installed side by side use a filler strip LOCATE ELECTRICAL OUTLET WITHIN LOWER The width of this filler strip will vary depending on the con SHADED AREA DOOR SWING CLEARANCE figuration and panels you use Be sure to add the filler strip width to your finished LOCATE WATER SUPPLY rough in dimension In any side by side installation add an ER additional one half inch to your combined numbers IMPORTANT NOTE Refer to the full scale illustrations FRONT VIEW in the center of this guide for s
59. the area behind the door panel must stay behind the front plane of the finished molding as noted in illustration 10 M VALANCE BY OTHERS 17 REMOVABLE MOLDING BY SUB ZERO TOP HINGE Kickplate Clearance Illustration 11 details the area below the lower drawer area where the operating mechanical equipment of the Sub Zero 700 Series unit is housed IMPORTANT NOTE A You must keep a min imum space of four inches clear below the bot tom edge of the lower drawer panel so the unit can be properly vented B In addition any dec orative base molding must be removable for possible servicing and cleaning of the con denser 10 254 OPTIONAL B BASE MOLDING MUST BE REMOVABLE d REN HY To WALL Illus 11 700 SERIES PLANR Dual Installations Optional components are necessary for the installation of two or more 700 Series units where there is two inches or less of space between the units Contact your Sub Zero distributor for the proper components and instructions Note that panel sizes will change refer to illustration 8 on page 25 Electrical A 115 volt 6OHz 15 amp circuit breaker and electrical supply are required A separate circuit servicing each base and tall unit is necessary Follow the National Electrical Code and local codes and ordinances when installing the receptacle IMPORTANT NOTE The electrical outlet must be placed so the grounding prong is to the
60. ther under these warranties or under any warranty arising by operation of law Sub Zero will not be responsible for any consequential or incidental damages arising from the breach of these warranties or any other Warranties whether express or statutory Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may apply This warranty gives oveners specific legal rights and owners may also have other legal rights which vary fram state te state Ta receive parts and or service amd the name of the nearest Sub Zero authorized service representative contact your Sub Zero dealer distributor or Sub Zero Freezer Company Service Department Box 44130 Madison WI 53744 41340 call B00 222 7820 or e mail us at custamerservices2subzera com These actual size Mustra tions enable you to understand some of the unique situations you may face as you design the 600 Series full size units into homes These pages can be easily removed and photo 13 4 Panel F d4 copied or used in your 4 1 L 4 L 4 Ya Panat tracings j illustrations A and B show handle placement for framed applications Also illustrations and you can see the difference between the standard full length han and the optional extended full length handle illustrated in the dashed line
61. ub Zero unit W Overlay Panel 287h6 3476 W Spacer Panel 271 331p W Backer Panel H Overlay Panel 91 4 H Spacer Panel 85 16 95 16 Backer Panel 815 16 915 16 283 16 343 16 104 40716 407116 46746 467 16 3915 391 2 451p 4515 403 16 463 16 46 6 403 16 111 4 121 4 1314 1414 1 05 16 11546 125 16 135 16 1015 16 1115 16 1215 16 1315 16 12 600 SERIES PLANNING INFORMATION Optional Grille Panel Specifications Framed Application Model G 650 561 642 680 632 690 Width of Grille Panel 283 6 343 16 343 16 403 16 403 16 463 16 463 16 ize uz 4x 14 15 815 16 915 16 101546 111546 1215 6 131506 maaa MD Gate ace E pou Height of Grille Panel Model 561 is standard on all 600 Series units Optional Grille Panel Framed Application In some instances you may want to use Sub Zero s optional panel grille for some of your installations This is available on all 600 Series units with the exception of Models 601R and 601F The sizes for the panel insert are listed in the Optional Grille Panel Specifications Framed Application chart The widths on all of the specific grille panels will be the same regardless of height for each model except the Model 561 The various heights of each of the grilles are shown next to the corresponding grille height Just com bine the mode
62. will merely install the Sub Zero However for the Models 427 and 427R you will have to have the stainless steel panels installed Model 424 Overlay Panels The overlay panels applied to the Model 424 should not be confused with the 600 Series overlay panel application The Model 424 panel will consist of only a frame and would be either the 5 8 inch or 3 4 inch panel you may be using It is affixed directly to the door itself with screws through a series of pre drilled holes in the perimeter of the door itself You DO NOT need any backer or spacer panel Refer to illustrations 2 and 3 to give you a better idea of the exact space our unit needs and how the panel fits in relationship with the unit Rails and stiles can be increased in size but should not exceed cabinet manufacturers standard width They cannot exceed overall door panel dimensions specified as they would interfere with the operation of the door The back sides of rails and stiles that will be visible through the glass door will need to be finished Also the inside edges of the frames must be finished to match the front surface Please note on the left hand side of the overall unit dimen sions where we have located pre drilled holes for our optional handle hardware Refer to page 39 for specifics about installing handle hardware on this overlay applica tion Other installation instructions will be provided in complete detail in a book which accompanies each unit
Download Pdf Manuals
Related Search