instruction manual - Strider Plus Pram Stroller
Contents
1. A Refer to section 14 for B Refer to section 11 for removing the seat from the fitting the seat to the frame frame 16 TO ADJUST THE HEAD PILLOW amp SHOULDER HARNESS HEIGHT NOTE The head pillow has a small height adjusting range for additional comfort PCT i d e i j DA J A aac el A The head pillow height B Unzip the pocket C Hold the slider and is adjustable The harness located on the rear side of squeeze the two buttons shoulder strap height also the Stroller seat to reveal together Slide up or down moves with the head pillow the head pillow slider to adjust the head pillow height as desired then zip the pocket closed 18 17 TO FIT USE AND REMOVE THE CANOPY A To attach the canopy B Attach the canopy C To adjust the canopy slide the canopy mouldings hook strips to the pile strips open by pulling forward onto the frame mouldings around the top of the frame or close by pushing it until they connect together for a secure fit backward D For extra protection E To expose the mesh F The zip should be fully pull visor out from under section of the canopy unzipped to expose the center front of canopy unzip the center section mesh section 19 STROLLER ASSEMBLY amp OPERATION 17 TO FIT USE AND REMOVE THE CANOPY CONTINUED G The window cover is H To open the window To remove the canopy kept in place by a hidden cover roll up the cover and pull the canopy off the magnet locate2. 16 B Press in and hold the C Release the button engaging release button then pull on the armbar to then insert the pin all the make sure it is engaged way in Repeat steps A B amp C for the other side E Rotate the armbar clear of the Stroller seat Lock the armbar back into position after fastening the child in the harness 13 ADJUSTING THE BACKREST CAUTION Ensure that your child s limbs are inside the seating area before adjusting the backrest Be prepared to support your child s weight when adjusting the backrest A To adjust up or down B Continue to hold the C There are 3 indicated fully lift the adjusting lever lever up and adjust the seat positions while the all the way up seat to any one of three seat is facing forward or positions rearward 1 Upright seating position 2 Semi recline seat position 3 Layback seat position 14 STROLLER SEAT REMOVAL WARNING Always remove your child from the Stroller seat before removing installing or changing seat direction A To remove the seat B Hold the seat or armbar C While holding the grey firstly place the seat in the on both sides with your buttons lift the seat out of most layback position 8 hands Then with your the frame see section 13C finger or thumbs press down and hold the grey buttons 17 15 TO FACE THE SEAT IN OPPOSITE DIRECTION WARNING Always remove your child from the Stroller seat before changing seat direction
3. C To fit the footmuff into the Stroller first unzip the top section from the padded bottom section and set the top section aside Place the padded bottom section into the Stroller seat F Thread the buckle housing amp crotch pad through the crotch slot in the footmuff Fit the reversible shoulder pads if desired 25 TO USE THE FOOTMUFF CONTINUED G The footmuff is now H Engage the other side ready for use Place the of the armbar See section child in the Stroller and 12 Roll the top section connect the harness of the footmuff over the buckle Ensure the armbar and secure with harness buckle is correctly the elastic and toggle if engaged see section required 18 Zip together the top amp bottom sections of the footmuff 26 TO FIT THE MESH COVER A To fit the mesh cover B Wrap the elastic loops C When fitted to the over the Stroller seat or around the Stroller handle Stroller the front section of Infant Carrier place the tube and attach together the mesh cover will rest on elastic section of the using the clip the leg support mesh cover over the front section of the canopy 25 26 TO FIT THE MESH COVER CONTINUED D Lift the fabric cover as required or lower for most protection G To fit the mesh cover over the Second Seat place the elastic section of the mesh cover over the front section of the canopy 26 ery E To fit the mesh cover F Wrap the elasti
4. C Pull up on the adaptors to make sure they are locked on CARE amp MAINTENANCE To prolong the life of your nursery product keep it clean and do not leave it in the direct sunlight for extended periods of time Removable fabric covers and trims may be cleaned using warm water with a household soap or a mild detergent Allow it to dry fully preferably away from the direct sunlight DO NOT DRY CLEAN OR USE BLEACH Do not machine wash tumble or spin dry unless the care labelling on the product permits these methods Non removable fabric covers and trims may be cleaned using a damp sponge with soap or mild detergent Allow it to dry completely before folding or storing it away In some climates the covers and trims may be affected by mould and mildew To help prevent this occurring do not fold or store the product if it is damp or wet Always store the product in a well ventilated area To maintain the safety of your nursery product seek prompt repairs for bent torn worn or broken parts Use only those parts and accessories tested and approved by Britax 47 WARRANTY Each Steelcraft unit is thoroughly inspected in our Quality Assurance department prior to delivery In the unlikely case that you find any faulty material or workmanship that affects the units normal operation we will repair the unit free of charge within 12 months of purchase You are required to present your receipt as proof of purchase For all concer
5. edtansndesanbcatencivees 22 222 PO UStADIE leg SUD DOM ccasacinesaccncadiinccatnatuinidiicacnadutatbedianidiacudaddudaanduiemidiecmadmaddidadunanideiunduadciwedarnaiaetdedualidds 22 Zoe OME Ele OO OUGON Cl aeriene E EAEE E E AEA E E e 23 24 TO USE ING DaSK El E E T EE N E E E E 23 25 10 Use Ne room asira EE AEA SAN EAEE EAE EEEE alec ERARE 24 26 VO HU the Mesh COVE eacee ERTE AA RERE RAE TEERADA 25 Afa TOt Ne TANOVOR E Aa E AOAN a 27 Bela Era aE a a e e EN AEE E E E A E EN A E EE A A T A E E N E 29 28 Bassinet assembly fitting amp removal secccinccisicnsesseseanieenacunesnesslevineccasmetesecaeedeseanviexladases yosclesaesbesianssecanees 29 E CT N aa T nme nner ee ee mcry emi nen ner en errr renee ame nner nee tre ro 29 Intant Carrier iting and TEMOVAl sacsinssinsaanctivesaiccannttuadandcenuessanntdhadaicdaxivtwbounedeuincdouaviaudieeddavinedeyarasvieen 32 30 To f ld close the Stolle acresca a rE a EAE AEn EEr Eade ERAR isien 35 E E a r E ret ener Shirin tent et een ee ser nt tinenner er re tant crsseete Terre errr Renter 38 31 FO USS the Second Seal iincaticosnstacticesapstomacanncesesunbsiassawacdaanendedssaretetasn addsudedhsieviensanicenidarsimcaveampadeintedts 38 31 1 To fit Second Seat to the Strollers ccseciecssaiacivorsvarecseassndsccuaheeradenensbelantantanantenaadenscebaeiedeatedweadaeadbantawen 40 31 2 To adjust into seating POSIUONS essssrnsiorsinerinia aneia iaaea ACRAEA EAEE AAEE aaiae 41 31 3 To fit use and remove the CANO DY vice
6. features however some features are in different locations as shown right STROLLER FEATURES 22 Canopy window S23 Backrest recline lever S24 Tether strap S22 S25 Head pillow adjustment slider under zip S26 Accessory bag S27 Rear wheel release S23 S28 Brake S24 S29 Mouldings for S25 attachment to second seat connecting pins S30 Second Seat release buttons S31 Lower mouldings for aan attachment to second seat frame Accessory bag and Stroller seat have been removed from the frame shown right STROLLER PARTS oe Stroller frame Stroller seat Armbar Tether strap Shoulder pads Seat pad B Accessory bag Mesh cover Front wheels 4 wheel model Rear wheels A p Wheel guards Raincover Bootcover 1 STROLLER FRAME OPENING A Lay the frame on a flat surface B Release the frame lock and lift up by the handle to partially open the frame C Continue to lift the handle up to open D Push down on the handle to confirm the frame until the left and right side frame the frame is locked open mouldings engage and lock together NOTE To fold close the frame see Section 30 STROLLER ASSEMBLY amp OPERATION A Position the left and B Fit each guard onto the C Pullon each guard right guards beside the moulding at the base of the in the direction shown to frame as shown leg tubes Push down until make sure they are locked
7. not in use store body band under the mattress NOTE D rings are installed in the base of the bassinet for optional baby harness installation Baby harness is not supplied but can be purchased separately at an independent baby shop 31 INFANT CARRIER ASSEMBLY amp OPERATION 29 INFANT CARRIER FITTING AND REMOVAL SOLD SEPARATELY WARNINGS e Do not leave the child in the carrier for extended periods e The carrier is designed to provide mobility outside of the car but it should not be used instead of an appropriate cot e Ensure the carrier must be correctly fitted and locked into the Stroller e The carrier must only be used with an SC or Steelcraft Stroller with compatible attachments e To be used only in a rearward facing position that is facing toward the Stroller handle e Use only for a child weighing up to 9kgs and with a length of up to 700mm e Remove Infant Carrier from Stroller frame before folding A Remove Stroller seat or Bassinet from frame see B Push down on the items 5B amp 19E The Infant Carrier must face the Stroller Infant Carrier and make handle With the Infant Carrier handle in the upright sure it is located in the position locate the Infant Carrier handle mouldings on frame mouldings The either side directly over the frame mouldings Notice the Infant Carrier now needs to indicator is GREEN be locked securely into the frame 32 29 INFANT CARRIER FITTING AND REMOVAL CONTI
8. position when used in conjunction with the Second Seat 38 S100 NDS AW By ate ts V a AsO ed le OlN 31 TO USE THE SECOND SEAT CONTINUED Parts supplied with Second Seat SS1 Second Seat assembly SS2 Second Seat engaging pins 2 SS3 One hand 4 position reclining backrest SS4 Adjustable removable canopy SS5 Safety lock SS6 Adaptors 2 SS7 Head Pillow SS8 Shoulder pads 2 39 31 TO USE THE SECOND SEAT CONTINUED 31 1 To fit Second Seat to the Stroller NOTE For easier installation rotate the Pivotal Handle in the most upright position A Remove the Accessory B The Second Seat Bag if fitted Apply the connecting pins SS2 Stroller brake rotate the need to lock into the frame pivot handle up to create mouldings S29 more assembly space Adjust the Stroller seat to the most upright position D Now allow the Second E Pull up on the Second Seat to drop down and lock Seat frame to make sure it into the lower Stroller frame is locked onto the Stroller mouldings S31 frame Ensure to grasp the Second Seat frame as shown above 40 C Hold the Second Seat and hook the connecting pins SS2 down into the frame mouldings S29 Inset photo shows correct engagement F Lift up by the head end of the Second Seat so that the foot end of the Second Seat slides down the Stroller frame and engages into the second lock SS5 SECOND SEAT ASSEMBLY amp OPERATION 3
9. rear of the Stroller and facing towards the Stroller The Second Seat must be correctly fitted and locked onto the Stroller Use only for a child weighing up to 15kgs A five point harness is provided to restrain your child To secure the child in the harness push buckles A through the buckle rings B and into the buckle housing C until the buckle prongs snap into position Carefully adjust the harness by pulling the sliders D until the desired fit is achieved in the lap shoulder and crotch straps Always adjust the harness when changing the seating position of the child To release the buckle squeeze the top and bottom buckle prongs A S1 Adjustable amp removable canopy S2 Pivotal handle S2 S3 Visor S4 Frame fold mouldings S3 on both sides S5 Canopy mesh S4 under zip S5 S6 Arm b n Arm bar S7 S7 Removeable amp reversible S8 Stroller seat S9 S8 Stroller seat release buttons on both sides S410 S9 Frame sockets on both sides accepts Stroller seat Infant Carrier bassinet or adaptors S10 Frame lock 11 Wheel guards 12 Side access zip pocket on both sides 13 Adjustable head pillow S14 Reversible seat pad S11 S12 S15 Reversible shoulder pads S16 5 point harness S17 Crotch pad S18 Adjustable footrest S19 Front access zip pocket 4 wheel model onl 4 wheel model only S04 S20 Front wheel release S21 Swivel wheel lock The 3 wheel model has similar
10. 1 TO USE THE SECOND SEAT CONTINUED 31 2 To adjust into seating positions A Adjust to desired B The seat will slide up seating position by using and down the frame Lock the one hand backrest into any one of 4 seating adjusting lever Lift the lever positions by releasing the all the way up and at the backrest adjusting lever at same time lift up on the the desired position seat 31 3 To fit use and remove the canopy Refer to section 17 To fit use and remove the Second Seat canopy is the same as the Stroller seat Canopy 31 4 Harness adjustment A five point harness is provided to restrain your child To secure the child in the harness push buckles A through the buckle rings B and into the buckle housing C until the buckle prongs snap into position Carefully adjust the harness by pulling the sliders D until the desired fit is achieved in the lap shoulder and crotch straps Always adjust the harness when changing the seating position of the child To release the buckle squeeze the top and bottom buckle prongs A Shoulder straps D Buckle Buckle Buckle Al prongs Ca Rousing prongs D a i So e j 5 a0 a au strap Buckle ring B al B Buckle ring Crotch strap D Slider 41 31 TO USE THE SECOND SEAT CONTINUED 31 5 Reversible shoulder pads NOTE The shoulder pads are reversible A Fit the reversible B Repeat for the other C The reverse side of the shoulder pads by fitting reve
11. 6 POO ate Me Ol Ae sesine E SE Ea aE EEE E resin tin eed 13 9 To adjust the pivotal handle 7 MOSIMIONS irnciicavtaisarndiucdv einai nictounereniacieantniaasadnbiewdsatinnedes mgeianksnduntroutl 13 10 TIE the accessory OO ie as cereentince aeracece sg innen EDENE AE EE Eien a a a 14 11 Fitting the stroller seat to the TANG sacicesccccacedantaiacanccucadencastaattwteninncadadtusectastnncdaseseddsnsateatenitiaacatdenceada 10 Te TONED AN A ea ausciad swede ctestetoesenuauaencencaneustvecunedatdemcen teste E 16 TS AdusiMho tne Dack EST rsen aa aE aA A AAE AEE RAR AEA A AROEN EERE 17 14 Stroller seat removal sescrcsnsotins aa NOAA A ERr EA 17 15 To face the seat in opposite direction n sesesnserrrrnrrnnrrrnrnrnrrrnnrrnnrrrnrrrnnrrnnrrnnrernnrrnnrennrennnennnenne 18 16 To adjust the head pillow amp shoulder harness Ne IGNt ccccsececssseeceseeeceeeeceeeeeceeeeeeseeessuseeseeeeee 18 17 To fit use and remove the CANODY cscs asicce cece nesndswauicecwstedeneweaceneeeinaxdadanssvewaduicadenctedatestiandeaesenteewsndepest 19 To Hames adus USI oe sence a secce sees ctiecanesedect nun eccteacannestasclodsecetie sa teneenosiocis EE 20 NUS We at Ai EN E EAE A Yada tetas E adi A E A E E E A 21 20 To fit the reversible seat DAG ics sauctssavuaviexas tattnninzrsuecdeieadesaeeieiesluiaeadeodieds ee nies eeenaaceueestsentoeeh 21 21 To use the reversible shoulder PAS wvisiscictaies oavessasesnucaenewentesieverssnesnssadeatass Alendesaubiedev
12. NUED C By squeezing in and holding the latches on either side of the handle rotate the handle backwards The GREEN Indicator will now turn to RED F IMPORTANT Pull up on both sides of the Infant Carrier and confirm it is locked into the frame If not locked in on both sides repeat steps A to E D Release the handle latches Then with one hand holding the front of the Infant Carrier push the Infant Carrier handle all the way down until you hear it lock into the frame G Secure your baby into the Infant Carrier by the harness provided E The handle indicator should now be GREEN and the Infant Carrier should be locked into the frame If indicator is RED the Infant Carrier handle is not in the locked position repeat step D H To remove the Infant Carrier squeeze both handle latches in to release the locks The indicator will now be RED 33 INFANT CARRIER ASSEMBLY amp OPERATION 29 INFANT CARRIER FITTING AND REMOVAL CONTINUED Continue to rotate J Lift and remove the the handle forward until Infant Carrier away from it returns to the upright the Stroller position Release the latches the indicator should now be GREEN 34 ASSEMBLY amp OPERATION 30 TO FOLD CLOSE THE STROLLER Remove the Bassinet or Infant Carrier if connected to the frame prior to folding The rain cover must also be removed it fitted NOTE Seat unit and wheels can be removed to reduce the total fo
13. Strider UUS INSTRUCTION MANUAL IMPORTANT KEEP THIS BOOKLET IN A SAFE PLACE FOR FUTURE REFERENCE Note Second Seat Bassinet Infant Carrier and Footmuff are all sold separately OOS SSS TT FFEIF EE IEF FFE SUNS INDEX Copot Ro gc ae eee ane inter ete ge ey cee ine Pere ere ne rr nee monroe Ur ere yer EE een er nee cer nr ener ere 3 Bassinet Infant Carrier amp Second Seat Waning Svcicsicaiassiissanssdaneiasnananiwringsandeiasiadsanunlasimnieiiedeiuasanlugassiniad 4 EEE i e EE E D N E E I A A E AE E A E N T E N E 5 PAN edee EE E E e E e ET e E EE E EEE 7 1 Stroller frame opening essar ale in lnc ced aCe A aA N denne urease 8 2 To fit and remove the wheel guardS s essssesssnnestreeernterenrtrrttrtrntntternttenntteetnteennteeetnteennneentteee nenene 9 3 Rear wheel fitting and WENO VA sis criss acciteee eaicetcenenieancunc caedencciaaasinc shows sale ninsmavied dee ebueaadine deeasns Mlaeeoersmauddessensaecxs 9 4 Front wheel fitting and removal 4 wheel MOel ce ccccesseeeeeeeeeeeceaseeeeeeaaeeeesaaeeeessaaeeeessaeeeessaneeees 10 5 Front wheel fitting and removal 3 wheel MOCEl ececcesceeeceeeeeecsaseeeessaaeeeesaaeeeessaeeeesaeeeessaeeees 11 6 Swivel fixed front wheel operation 4 wheel MOEl cccccccseseeeceeseeeeseeseeeceaaeeeeseaeeeseaneeesseageeees 12 7 Swivel fixed front wheel operation 3 wheel MOEl cccccecccecseeeeeceeseeeeceaeeeeceaaeeeeceaaeeessaeeeessaaees 12
14. c loops over the bassinet place and clips around the hook the elastic section of the and pile strips and attach mesh cover over the front together using the clip section of the canopy H Wrap the elastic loops Attach using the clip and clips around the bars at both sides of the Second Seat STROLLER ASSEMBLY amp OPERATION 2 7 TO FIT THE RAINCOVER A1 To fit the raincover to A2 Pull the rear raincover A3 Join the hook and pile the Stroller Place over the section down between the around the handle tube Stroller canopy as shown handle and down the back Loop the elastic section of the Stroller over the Stroller seat leg support A4 The raincover can be B1 To fit the raincover to C1 To fit the raincover to fitted to the Stroller seat the Stroller and Second the Infant Carrier Place when in forward or rear Seat Follow step A1 over the Infant Carrier facing mode then pull the rear raincover canopy as shown The section down between the elastic section will hang handle and over the back of over the front of the Stroller the Second Seat as shown above Attach the hook and pile as described in A3 above 27 STROLLER ASSEMBLY amp OPERATION 27 TO FIT THE RAINCOVER CONTINUED C2 Pull the rear raincover C3 Join the hook and pile D1 To fit the raincover section down between the around the handle tube to the Infant Carrier and handle Second Seat Follow step C1 then pull the rear ra
15. cidncncactcnuetcnsnadtimcsaunnonestucnaceemsidvananeaieenserbaneteinedertunanersnratcansanens 41 314 hamess adis time sra A E AR 41 31 95 Reversible shoulder DAG Sissin aink n ER e R E RE EER AART O 42 31 6 To adjust the head pillow and harness shoulder strap height POSItION ccccssseesseeeeseeeeeseeees 42 31 7 To fold the Second Seat while attached to the fraMe ccccccccccssseceeeeeeeceeeeseeceeesseeeseeeeeseseaeeess 43 31 8 TO remove Second Seat from the TAIN aise siansodercsuranseraicoardedeaensavansieanectsoninesevaxaiidedadeiacunsanendinareen 44 31 9 To use the adaptors with the Stroller SCAU caves iscceiveccssianicedaevecenasntneeeustiwvarsvsberenneadsaiaswanvetwumnanes 45 31 10 To use the adaptors with the Infant Carrier cccccccccsssececeeseeeeceaeseeceaaeeeeseaaeeeseeaeeeeseaeeeeeaagess 46 Gare anad Mantenan E sssri E Ea iae aana EEEa 47 WAU S A ETEEN E E E PE AIE AA A A O I A AE E 48 WARNINGS READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE OF THE Stroller ALWAYS FOLLOW THE INSTRUCTIONS THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL GENERAL WARNINGS e Check that all safety locks are engaged before placing a child in the Stroller e Ensure your child is secured with a correctly adjusted safety harness e Do not leave children unattended e Always apply the brakes when parking the Stroller e Never let go of the Stroller when parked on an incline because it may slide e Whe
16. d at the secure with the elastic and frame mouldings bottom of the window toggle cover 18 HARNESS ADJUSTMENT WARNING Use this harness at all times WARNING Buckle prongs A should always be fitted to buckle rings B A five point harness is provided to restrain your child To secure the child in the harness push buckles A through the buckle rings B and into the buckle housing C until the buckle prongs snap into position Carefully adjust the harness by pulling the sliders D until the desired fit is achieved in the lap shoulder and crotch straps Always adjust the harness when changing the seating position of the child To release the buckle squeeze the top and bottom buckle prongs A To adjust harness height position see section 16 Shoulder straps D Buckle prongs Buckle housing AS A a0 a au strap Buckle ring B gt B Buckle ring Crotch strap Dj Slider 20 19 TETHER STRAP WARNING Use the tether strap to prevent the Stroller from rolling away NOTE A tether strap is fitted to this Stroller always place the loop over desired wrist when using the Stroller A If the tether strap is removed attach by looping over the handle open one end of the tether strap and insert the opposite end through the opening created Pull until tether strap tightens around handle B Slide your hand through the tether strap whenever you use the Stroller Hint If tether strap is fitted in th
17. der the armbar studs to keep in place Hook the bootcover and then back over the top The Bootcover is now ready pocket under the leg for use support 24 TO USE THE BASKET NOTE When a child is in the Second Seat basket access is recommended only from the sides or from the front on 4 wheel models only There is no front access to the basket on 3 wheel models A Access is available B Access is available C Access is available from either side by undoing from the front by undoing from the rear of the Stroller the zippers the zipper on 4 wheel models only 23 25 TO USE THE FOOTMUFF PURCHASED SEPERATELY A To prepare the Stroller for fitment of the footmuff firstly ensure the head pillow height is correctly adjusted for your child see section 16 Fold the canopy back disengage one side of the armbar and rotate to the side of the frame see section 12D D Thread the harness through the slots in the footmuff Start by threading both lap strap buckle prongs through the pair of slots in the middle section of the footmuff 24 B Undo the buckle prongs from the buckle housing then release the buckle rings from the buckle prongs Remove the reversible seat pad amp shoulder pads E The footmuff features 3 pairs of shoulder strap slots to cater for different shoulder strap height positions Thread the shoulder strap buckle rings through the appropriate shoulder strap slots in the footmuff
18. e both red fixed position when you position latches down until they move the Stroller forward lock by approximately one metre 7 SWIVEL FIXED FRONT WHEEL OPERATION 3 WHEEL MODEL NOTE Always lock the front swivel wheel when on uneven surfaces A For swivel wheel mode B To lock the front C The front wheel will lift the lever into the upright swivel wheel into the fixed automatically lock into the position until it locks position press in the button fixed position when you on the swivel release move the Stroller forward moulding The lever will by approximately one rotate downwards metre 12 STROLLER ASSEMBLY amp OPERATION 8 TO OPERATE THE BRAKE WARNING Always apply the brakes when parking the Stroller The Stroller may roll away even if left unattended for a few moments A To lock both rear B To unlock both rear wheels press the red brake wheels firmly lift up the lever all the way down brake lever all the way until Push the Stroller back and it locks into the up position forth to confirm the wheels are locked 9 TO ADJUST THE PIVOTAL HANDLE 7 POSITIONS A There is an adjusting B Press both buttons in C When the desired button on the inside of each together and hold Now height position has been handle moulding rotate the handle up or achieved release both down to the desired height buttons position 13 10 TO FIT THE ACCESSORY BAG NOTE Adjust the pivot handle up to create more asse
19. e centre of the handle you can use it with either hand 20 TO FIT THE REVERSIBLE SEAT PAD NOTE To assit with installing release one side of the armbar see item 12D and release the harness buckles A Fit the reversible seat pad by sliding it under the harness and head pillow Note Locate wider part of pad towards the head B Locate the reversible seat pad as shown C If you want to use the tether strap with the other hand slow to a stop and apply the brake see section 8 Loosen the tether strap and slide to the desired side of the handle Slide your hand through the tether strap before unlocking brake C The reverse side of the seat pad has a different fabric pattern 21 21 TO USE THE REVERSIBLE SHOULDER PADS NOTE The shoulder pads are reversible A Fit the reversible B Repeat for the other C The reverse side of the shoulder pads by fitting reversible shoulder pad shoulder pad has a different around the harness fabric pattern To reverse shoulder strap and attach undo the hook and pile the hook and pile and reattach on the reverse side 22 ADJUSTABLE LEG SUPPORT A To lower or raise leg B While holding both left support press in and hold and right buttons tilt leg both left and right buttons support up or down to the desired position 22 23 TO FIT THE BOOTCOVER A Raise the leg support B Pull the top of C Connect the press to the horizontal position bootcover un
20. front swivel wheels when on uneven surfaces to minimize wheel wobble The canopy will not give your child total protection from the harmful rays of the sun THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE WARNINGS BASSINET WARNINGS Always remove your child from the Bassinet before fitting or removing from Stroller The Bassinet must be removed from the frame before folding Do not lift Stroller by the Bassinet Only use Strider Bassinet with the Strider Plus Stroller Use a harness once the baby can sit up unaided INFANT CARRIER WARNINGS Do not leave the child in the carrier for extended periods The carrier is designed to provide mobility outside of the car but it should not be used instead of an appropriate cot Ensure the carrier must be correctly fitted and locked into the Stroller The Infant Carrier must only be used with an SC or Steelcraft Stroller with compatible attachments To be used only in a rearward facing position that is facing toward the Stroller handle Use only for a child weighing up to 9kgs and with a length of up to 700mm Remove Infant Carrier from Stroller frame before folding Always secure your child with the harness provided SECOND SEAT WARNINGS The Second Seat cannot be used in conjunction with the Bassinet The Second Seat must only be used with a SC or Steelcraft Stroller with compatible attachments Second Seat to be used only in a forward facing position That is connected to the
21. incover section down between the handle and over the back of the Second Seat as shown above Attach the hook and pile as described in C3 shown left E1 To fit the raincover to E2 Join the hook and pile the Bassinet Place over around the handle tube the Bassinet canopy as shown Loop the elastic over the front of Bassinet 28 28 BASSINET ASSEMBLY FITTING amp REMOVAL oPTIONAL ACCESSORY WARNING Remove Stroller seat or Infant Carrier from the frame before fitting Bassinet WARNING Always remove your child from the Bassinet before fitting or removing from the Stroller WARNING Bassinet must always face towards the handle WARNING The Bassinet must be removed from the frame before folding WARNING Do not lift Stroller by the Bassinet Only use Strider Bassinet with the Strider Plus Stroller Use a harness once the baby can sit up unaided A To assemble bassinet B Frame support rods C Push down lightly locate straps in the centre are locked under all four on the top edges of the of the frame support rods clips bassinet to check that the and pull straps slowly frame supports are firmly outwards until each rod locked in place slides and locks under all 4 Clips D Open canopy by E Fit the liner by aligning F Fasten hook and loop pressing and holding each the opening with the strip just under the main button on the outside of main locking lever and locking lever canopy pivot joint before stretching it over b
22. lded size if required See sections 4 or 5 amp 14 for reference With the seat attached adjusting and folding the leg support will also help to reduce folded size FOLDING TIPS Refer to photos following the folding proceedure A It is recommended for easier handling to take the Stroller seat off first Then fold the frame and put both seat and frame in the car B For smaller cars it may also be convenient to simply remove the rear wheels as well C If you choose to keep the Stroller seat attached ensure the Stroller seat is forward facing prior to folding This will achieve a more compact fold A Engage rear brakes B If seat unit is attached C If seat unit is attached Remove all objects and in child facing away and in child facing parent from seat back pocket from parent mode then mode then adjust the and basket and close the adjust the backrest to backrest to most reclined canopy before folding most upright position position 35 ASSEMBLY amp OPERATION 30 TO FOLD CLOSE THE STROLLER CONTINUE D Release the front E Return the pivot F Pull release mouldings wheels into swivel mode handle to the straight 1 amp 2 all the way up and to allow for more compact position hold to release the frame folding as shown above locks for 4 wheel models Refer to section 7 for 3 wheel models G Push down on the H Fold all the way down Frame lock engaged handle and the frame will until the frame lock engages begi
23. ly folded position above To fold the Stroller frame see section 30 You may need to adjust the pivot handle if it interferes with the frame 43 31 TO USE THE SECOND SEAT CONTINUED 31 8 To remove Second Seat from the frame WARNING Remove the child from the Second Seat before attempting to fold A First fold the Second B With the Second Seat C Hold the sides of the Seat up under the frame in the folded position Second Seat with each see item 31 7 locate the two grey release hand Simultaneously buttons S30 on the sides press in and hold both of the frame grey release buttons at the same time lifting the seat up away from the Stroller frame D Now push the Second E Lift the second seat out Seat up in the direction and away from the frame indicated by the arrow so the Second Seat connecting pins SS2 lift out of the frame mouldings S29 44 SECOND SEAT ASSEMBLY amp OPERATION 31 TO USE THE SECOND SEAT CONTINUED 31 9 To use the adaptors with the Stroller seat NOTE Adaptors are supplied to create more space if required when using the Second Seat For correct connection to the Stroller frame the adaptors move the Stroller seat mounting closer to the front of the Stroller DO NOT install the Stroller seat in a rearward facing position when used in conjunction with the Second Seat A Align the adaptor with B Press down on the C Pull up on the adaptors the Stroller frame mouldings adap
24. mbly space refer to section 9 A The bag firstly needs to B Hold the bag up by the C Attach the hook strip to be attached to the pile strip black back flap on the rear the pile strip on the inside on the inside of the Stroller side of the bag Note the of the basket This will help basket hook strip on the edge of to keep it in place Note the flap this flap also contains two pockets D Now thread each hook E Attach each strap tothe F The accessory bag is strap through the frame pile strips sewn on the bag to now ready for use Return moulding as shown hold in place the pivot handle to the desired position 14 11 FITTING THE STROLLER SEAT TO THE FRAME NOTE The seat is reversible so it can face in either forward or rearward position A Hold the Stroller seat over the frame B Align the Stroller seat mouldings on both sides over the frame connection sockets located in the middle of the Stroller C Push the Stroller seat down until both D Pull up on both sides of the Stroller seat mouldings are locked into the frame seat to make sure it is securely locked into sockets the Stroller frame 15 12 TO FIT THE ARMBAR A One side at a time align the armbar pin with the frame moulding as shown D The armbar can be released on one side and rotated out of the way to assist with putting a child in the Stroller To do this press in and hold the release button then disconnect one side of the armbar
25. n making adjustments to the Stroller ensure that your child s body is clear of any moving parts otherwise they may be injured e Remove child from the Stroller before going up or down stairs or escalators e Remove your child from the Stroller seat before changing the seat unit direction e Do not lift the Stroller by the armrest bar because it may disengage e Do not carry additional children on the Stroller e Do not allow children to stand on the seat e Do not hang bags or goods from the handle as this could cause the Stroller to tip over e Do not place more than 4kgs in the basket 1kg in the seat backrest pocket 1kg in the Bassinet pocket or 1kg in the Accessory Bag e To prevent the risk of the Stroller catching fire do not park it near an exposed heat source such as a radiator open fire barbecue etc e t may be unsafe to use accessories other than those tested and approved by Britax e Remove Bassinet from the Stroller frame before folding Stroller e The weight of the child using this product should not exceed 17kgs for the Stroller and 9kg for the Bassinet 9kg for the Infant Carrier or 15kg for the Second Seat NOTE The upright positions are not suitable for use with children less than six months old The lowest recline position should be used for babies and then the backrest can be adjusted to a more upright position as the child grows older and is able to support it s head without assistance Always lock the
26. n to fold 36 ASSEMBLY amp OPERATION 30 TO FOLD CLOSE THE STROLLER CONTINUE Compact Folding Tips Stroller seat separated from The two separate Separation of the Stroller seat the frame prior to folding components shown after and frame promotes easier folding handling and storage 37 SECOND SEAT ASSEMBLY amp OPERATION 31 TO USE THE SECOND SEAT WARNINGS e The Second Seat cannot be used in conjunction with the Bassinet e The Second Seat must only be used with a SC or Steelcraft Stroller with compatible attachments e Second Seat to be used only in a forward facing position That is connected to the rear of the Stroller and facing towards the Stroller e The Second Seat must be correctly fitted and locked onto the Stroller e Use only for a child weighing up to 15kgs e A five point harness is provided to restrain your child To secure the child in the harness push buckles A through the buckle rings B and into the buckle housing C until the buckle prongs snap into position Carefully adjust the harness by pulling the sliders D until the desired fit is achieved in the lap shoulder and crotch straps Always adjust the harness when changing the seating position of the child To release the buckle squeeze the top and bottom buckle prongs A Refer to section 18 Recommended Stroller seat position when DO NOT install the Stroller seat in a used in conjunction with the Second Seat rearward facing
27. ns with your product please contact our Customer Service team CUSTOMER SERVICE 1300 303 330 Australia 0508 688 822 New Zealand Please read all the information carefully before using this product This warranty does not apply to failure due to improper care or normal wear and tear caused by product use We reserve the right to inspect the unit You may be charged for repairs if the product has been damaged accidentally NEW ZEALAND BRITAX CHILDCARE NZ Limited A Britax International company 101 Diana Drive Glenfield Auckland 9 New Zealand Phone 09 443 0102 Fax 09 443 0120 Distributed by AUSTRALIA BRITAX CHILDCARE PTY LTD A Britax International company Incorporated in Victoria A B N 55 006 773 600 99 Derby Road Sunshine Victoria 3020 Australia Phone 03 9288 7288 Fax 03 9311 5798 Due to our continuing program of development Britax reserves the right to alter the specifications colour or design without any further notice The Steelcraft Strider and Strider Plus trademark the property of Britax Childcare Pty Ltd Australia The Britax trademark is the property of Britax Excelsior Limited UK Visit the Britax website at http www britax com au or email us at custserv britax com au Due to the variations in the style and design of our products the illustrations used in this instruction booklet are generic 2009 Copyright Britax Childcare Pty Ltd Australia Te Steelcraft Deaesess820 0 sessesesss
28. oth rotating carry handle bar to corners of the Bassinet vertical position Ensure body band faces upwards 29 28 BASSINET ASSEMBLY FITTING AND REMOVAL CONTINUED G Fasten hook and loop tabs around the handle mouldings and stretch the liner over the other two corners of the bassinet H Fold canopy down refer to item 28D Insert the pad into the bassinet with head rest located at the canopy end Attach hook and loop tabs on canopy to the liner on both side and in 2 places near the main locking lever NOTE The bassinet can only be installed rearward facing mother position on the Stroller frame The frame will not fold with bassinet installed so it must be removed before folding J Line up plastic moulding on sides of Bassinet with sockets in the middle of Stroller frame 30 K Lower the Bassinet all the way down until it engages into the sockets on both sides L Ensure Bassinet is securely locked on by trying to pull up BASSINET ASSEMBLY amp OPERATION 28 BASSINET ASSEMBLY FITTING AND REMOVAL CONTINUED M To remove Bassinet N Continue to hold lever NOTE A body band is also from the Stroller firmly lift up and once released lift installed in the base of the up and unlock the main the bassinet out of the Bassinet for optional use lever Stroller To use the body band remove the mattress open the body band and then place the mattress back into the Bassinet When
29. rsible shoulder pad shoulder pad has a different around the harness fabric pattern To reverse shoulder strap and attach undo the hook and pile the hook and pile and reattach on the reverse side 31 6 To adjust the head pillow and harness shoulder strap height position A The head pillow has B The harness straps are a small height adjusting threaded through the head range Attach to the best pillow so the shoulder strap suited hook and pile height is adjusted when position as required the head pillow height is adjusted 42 31 TO USE THE SECOND SEAT CONTINUED 31 7 To fold the Second Seat while attached to the frame WARNING Remove the child from the Second Seat before attempting to fold NOTE Fold the Second Seat before folding the Stroller A Fold the canopy back then fully lift up the backrest adjusting lever and hold in this position B At the same time push down on the Second Seat the foot end of the Second Seat slide will slide up and stop at the safety lock position lowest recline position C The image above shows the Second Seat at the safety lock position lowest recline position D While still holding the backrest adjusting lever up slide the grey safety lock button SS5 up then lower the head end of the Second Seat E Continue to lower the Second Seat the foot end of the Second Seat will slide up the frame to the folded position F The Second Seat is shown in the ful
30. s ll a th hh ht hd bp gt gt gt gt gt www striderplus com au ART No 4001103
31. they lock into position on correctly A To fit the rear wheels B Pullon the rear wheel C To release the rear align the wheel axle to make sure it is locked wheels press down and rod with the hole in the on Repeat steps A amp B to hold the metal release tab wheel moulding Push the fit the other rear wheel Then slide the wheel out rear wheel into the wheel and remove Repeat for the moulding until it locks into other side position 4 FRONT WHEEL FITTING AND REMOVAL 4 WHEEL MODEL NOTE Tip the frame backwards for more A Take each front wheel assembly and convenient assembly push the axle into the wheel housing until it locks in B Pullon both front wheel sets to make C To remove the wheel assembly turn sure they are locked on top knob to the left to unlock and release the wheel 10 NOTE Tip the frame backwards for more A Take the front wheel assembly and convenient assembly push the axle into the wheel housing until it locks in B Pullon the front wheel to make sure it C To remove the wheel assembly push is locked on the metal tab all the way back to unlock release and remove the wheel 11 6 SWIVEL FIXED FRONT WHEEL OPERATION 4 WHEEL MODEL NOTE Always lock the front swivel wheels when on uneven surfaces A For swivel wheel mode B To lock the front C The front wheels will slide both red latches wheels into the fixed automatically lock into the up until they lock it into position slid
32. tors to lock into the to make sure they are as shown and ensure the Stroller frame mouldings locked on adaptor extends towards S9 the front of the Stroller and the ribbed section of the mouldings face inwards D Lock the Stroller seat E Adjust the Stroller into the adaptors in the backrest angle as required forward facing position WARNING Stroller seat must be correctly attached see fitting and removal sections 11 amp 14 45 31 TO USE THE SECOND SEAT CONTINUED 31 10 To use the adaptors with the Infant Carrier NOTE Adaptors are supplied to create more space if required when using the Second Seat For correct connection to the Stroller frame the adaptors move the Infant Carrier mounting closer to the front of the Stroller DO NOT install the Infant Carrier in a forward facing position even when used in conjunction with the Second Seat The Infant Carrier must always face rearward A Align the adaptor with B Press down on the the Stroller frame mouldings adaptors to lock into the as shown and ensure the Stroller frame mouldings adaptor extends towards S9 the front of the Stroller and the ribbed section of the mouldings face inwards D Lock the Infant Carrier into the adaptors with the Infant Carrier facing towards the Stroller handle WARNING Infant Carrier must be correctly attached refer to section 29 E Pull up on the Infant Carrier to make sure it is locked in 46
Download Pdf Manuals
Related Search