Wall-Mount Bracket
Contents
1. The wall should be capable of supporting a weight of at least four times the TV weight Refer to your TV s instructions for its weight e If the installation of the Wall Mount Bracket on the wall is not sufficiently sturdy the unit may fall and cause injury or property damage Be sure to subcontract moving or dismounting of the TV to licensed contractors If persons other than licensed contractors transport or dismount the TV it may fall and cause injury or property damage Be sure that two or more persons carry or dismount the TV Do not spill liquid of any kind on the TV If you allow the TV to get wet this may result in a fire or an electric shock Do not remove screws etc after mounting the TV If you do so the TV may fall and cause injury or property damage Do not disassemble or make alterations to the parts of the Wall Mount Bracket If you do so the Wall Mount Bracket may fall and cause injury or property damage Do not mount any equipment other than the specified product This Wall Mount Bracket is designed for use with the specified product only If you mount equipment other than specified it may fall or break and cause injury or property damage Do not cover the ventilation holes of the TV If you cover the ventilation holes with a iji seg cloth etc heat may build up inside and Ez cause fire O1 Do not apply any load other than the TV on the Wall Mount Bracket If you do2. when it is pushed upward and cause injury Confirming the 3 Be sure to hold the TV and slide it upward to remove the TV completion of the installation Check the following points The hooks of the Mounting Hook are firmly latched in the holes of the Base Bracket e The cord and the cable are not twisted or pinched e The two screws that secure the Mounting Hook and the Base Bracket are securely tightened CAUTION Be careful not to allow the cord and cables to get WARNING caught when removing the TV Do not adjust the angle of the Mounting Hook when the e Be careful not to hurt your hands or fingers when TV is installed on the wall and be sure to install removing the TV completely It may cause the product to fall and result in injury or product damage Also improper placement of WARNING WARNING the AC power cord etc may cause fire or electric shock through a short circuit Be sure that two or more persons hold the TV when Be sure to confirm the completion of the installation for carrying it safety When removing the TV Specifications To Sony Dealers Weight 4 7 kg 1 Unplug the AC power cord from the wall outlet 2 Remove the two screws which secure the TV and the Base Bracket Refer to 3 of Step 5 on page 10 for the screw positions Design and specifications are subject to change without notice 11 GB The tab
3. Mounting Hook from the Base Bracket Mounting Hook Be careful not to drop the Mounting Hook when removing the screws from the Mounting Hook The screws required for this procedure are not supplied Select screws suitable for the material and structure of the wall If the Base Bracket cannot be attached securely enough use additional screws Be sure to confirm that the Base Bracket is securely attached to the wall 7 GB Step 4 Preparing for the installation of the TV If you intend to install a TV that is not specified on page 2 be sure to refer to the leaflet Installing the Wall Mount Bracket supplied with your TV 1 Remove the screws from the rear of the TV Then detach the Table Top Stand from the TV Place the TV with its screen facing down on a stable cloth covered work surface For the following TV users KLV 46 40D300A KLV 46 40V300A Soft cloth For the following TV users KLV 37M300A et e Soft cloth 8 GB For the following TV users KLV 32D300A KLV 32V300A KLV 32M300A Soft cloth e When removing the Table Top Stand from the TV lay the display face down on a stable work surface that is larger than the TV To prevent damaging the surface of the LCD display make sure to place a soft cloth on the work surface If pressure or shock is applied to the surface of the TV the LCD display may break o
4. TV When installing the TV onto the Base Bracket a b Hook position a cannot be used for the models in the table above 13 GB lie fal LBA RRA IRA A BERN KN aS 3777 5 ABa 201201 http www sony com cn Printed in China
5. fire an electric shock or a malfunction of the TV e If you use the TV installed on the Wall Mount Bracket for a long time the wall behind or above the TV may become discolored or the wallpaper may come unstuck depending on the material of the wall e Ifthe Wall Mount Bracket is removed after installing it on the wall the screw holes are left e If you have routed 300 ohm feeder cables behind the wall we recommend that you change them to 75 ohm coaxial cables If it is necessary to continue to use 300 ohm feeder cables be sure there is sufficient space available between the TV and the feeder cables behind the wall before installing Consult your licensed contractor regarding an appropriate location free from radio noise etc before installing 4 GB To Sony Dealers WARNING To Customers Sufficient expertise is required for installing this product Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation To Sony Dealers The following instructions are for Sony Dealers only Be sure to read safety precautions described above and pay special attention to safety during the installation maintenance and checking of this product Be sure to install the Wall Mount Bracket securely to the wall following the instructions in this instruction manual If any of the screws are loose or fall out the Wall Mount Bracket may fall
6. screws are securely tightened with equal torque strength to the rear of the TV arm using the two screws removed in the previous procedure O Screw Mounting PSW6 x 16 Hook Square hole Align the tab on the rear of the Mounting Hook with the square hole on the rear of the TV as in e Be sure to adjust the right and left arms to the same angle the illustration below e Make sure that the two arm bases are screwed in securely Be careful not to pinch your fingers when adjusting the angle of the Mounting Hook Notes on the adjustment angles e When installing TV models other than those specified on page 2 depending on the model s size and dimensions etc the adjustment angles listed 0 5 10 15 20 degrees for the arms may be limited e For the available adjustment angles of the arms when installing TV models other than those specified on page 2 refer to the operating instructions or the leaflet Installing the Wall Mount Bracket supplied with the TV Square hole Be sure not to use any screws other than the supplied ones PSW6 x 16 when securing the Mounting Hook 9 GB Step 5 Installing the TV on the wall If you intend to install a TV that is not specified on page 2 be sure to refer to the leaflet Installing the Wall Mount Bracket supplied with your TV Be sure to complete the installation before connecting the AC power cord to the wall out
7. so the TV may fall and cause injury or property damage Do not lean on or hang from the TV Do not lean on or hang from the TV as it i may fall on you and cause serious injury LA amp Jj Do not expose the TV to rain or moisture It may cause a fire or an electric shock Never place the TV in hot humid or excessively dusty places or in a place where the TV is subjected to mechanical vibrations If you do so it may cause a fire or an electric shock Keep flammable objects or open flames e g candles away from the TV To prevent a fire keep flammable objects or open flames e g candles away from the TV 3 GB Do not install the Wall Mount Bracket on wall surfaces where the corners or the sides of the TV protrude away from the wall surface Do not install the Wall Mount Bracket on wall surfaces such as a pillar where the corners or the sides of the TV protrude away from the wall surface If a person or object happens to hit the protruded corner or side of the TV it may cause injury or property damage Do not handle the product with excessive force during cleaning or maintenance Do not apply excessive force on the topside of the TV If you do so the TV may fall and cause injury or property damage Do not install the TV over or under an air conditioner If the TV is exposed to water leaks or air current from an air conditioner for a long time it may cause a
8. weight of at least four times that of decide on the installation location the TV Refer to your TV s instructions for its weight Allow for suitable clearance between the TV and the ceiling and protruding parts of the wall as shown below Determine the strength of the wall the TV will be mounted on Reinforce the wall sufficiently if necessary Unit mm o S en 100 100 Never install the TV set as shown below Air circulation is blocked If you intend to route the cables in the wall make a hole in the wall to insert the cables before beginning the installation 6 GB Ste p 3 Secure the Base Bracket and the Mounting Hook on Z the wall using the four or more 8 mm diameter or n stal l i n g th e Base equivalent screws not supplied B rac ket on the wal l Select four screw holes with the mark shown in the diagram below and tighten the screws securely so that they will not become loose Align the unit so that it is level 1 Secure the Base Bracket to the wall using four or more 8 mm diameter or equivalent screws not supplied O Determine the screw holes d h for attaching the Mounting Hook to the Base Bracket Then attach them securely using the supplied screws BVST4 x 12 Screw BVST4 x 12 Base Bracket Remove the screws which were attached in procedure and detach the
9. S ONY 3 217 571 E2 1 To Customers and Sony Dealers Wall Mount Bracket Instructions SU WL500 2007 Sony Corporation Thank you for purchasing this product To Customers Sufficient expertise is required for installing this product Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation Sony is not liable for any damages or injury caused by mishandling or improper installation or installing any other than the specified product Your Statutory Rights if any are not affected If the safety precautions are not observed or the product is used incorrectly it may result in serious injury or fire This instruction manual shows the correct handling of the product and important precautions necessary to prevent accidents Be sure to read this manual thoroughly and use the product correctly Keep this manual available for future reference To Sony dealers Sufficient expertise is required for installing this product Be sure to read this instruction manual thoroughly to do the installation work safely Sony is not liable for any damages or injury caused by mishandling or improper installation Please give this manual to the customer after installation Products by Sony are designed with safety in mind If the products are used incorrectly however it may result in a serious injury through fire electric shock the product topp
10. and cause injury or property damage Be sure to use the appropriate screws for the material of the wall and install the unit securely using four or more 8 mm diameter or equivalent screws Be sure to use the supplied screws and attachment parts properly following the instructions given in this instruction manual If you use substitute items the TV may fall and cause bodily injury to someone or damage to the TV Be sure to assemble the bracket properly following the instructed procedure explained in this instruction manual If any of the screws are loose or fall out the TV may fall and cause bodily injury to someone or damage to the TV Be sure to tighten the screws securely in the designated position If you fail to do so the TV may fall and cause bodily injury to someone or damage to the TV Be careful not to subject the TV to shock during installation If the TV is exposed to shock it may fall or break apart This may cause injury Be sure to install the TV on a wall that is both perpendicular and flat If you fail to do so the TV may fall and cause injury After proper installation of the TV secure the cables properly If people or objects get tangled with cables this may result in injury or damage to the TV Do not allow the AC power cord or the connecting cable to be pinched If the AC power cord or the connecting cable is pinched between the unit and the wall or is bent or twisted by f
11. le below shows the dimensions of the TV that is mounted on this product Refer to this table to decide on the installation location If you intend to install a TV that is not specified below be sure to refer to the leaflet Installing the Wall Mount Bracket supplied with your TV Screen centre point Unit mm on Screen cen tre Length for each mounting angle Model name Angle 0 Angle 20 O O Ej KLV 46D300A KLV 46V300A 1114 730 106 505 175 373 705 545 KLV 40D300A KLV 40V300A 981 643 157 505 170 338 622 543 KLV 37M300A 918 609 143 474 168 335 583 508 KLV 32D300A KLV 32V300A 790 530 137 424 160 318 516 464 KLV 32M300A 796 544 171 472 159 305 522 502 Some models may not be available in certain regions Figures in the above table may differ slightly depending on the installation The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV Refer to your TV s instructions for its weight 12 GB Model name Screw Hook location location KLV 46D300A KLV 46V300A e 9 KLV 40D300A KLV 40V300A i b KLV 37M300A KLV 32M300A d f KLV 32D300A KLV 32V300A f j c Some models may not be available in certain regions Screw location Hook location When installing the Mounting Hook on the
12. let If you allow the AC power cord to be pinched under or between pieces of equipment this may result in a short circuit or an electric shock Be careful not to stumble over the AC power cord or the TV as you may hurt yourself 1 Connect the AC power cord and the connecting cable s supplied with the TV to the TV Connect the AC power cord and the connecting cable s to the connectors on the rear of the TV For details on connecting the AC power cord and the connecting cable s refer to the instruction manual of the TV e You cannot connect the cables to the TV after installing it on the Base Bracket e Subcontract the cable routing in the wall to a licensed contractor 2 Install the TV onto the Base Bracket Referring to the Screw and Hook locations diagram table on page 13 determine the holes of the Base Bracket for latching the upper hooks of the Mounting Hook O Hold the TV securely with both hands and gently align it on the wall Be sure that two or more persons hold the TV when carrying it 10 GB e VaUbWcWY UcUbUWaUy 3 Mounting Hook Base Bracket Firmly secure the TV and the Base Bracket using the two supplied screws BVST4 x 12 BVSTA x 12 When using an electric screwdriver set the torque setting to approximately 1 5 N m 15 kgf cm Be sure to tighten both left and right securing screws firmly If you fail to do so the TV may fall
13. ling over or the product dropping Be sure to observe the precautions for safety to prevent such accidents 2 GB Specified products The following products are subject to change without notice may be out of stock or discontinued Also certain models are sold in some regions KLV 46D300A KLV 46V300A KLV 40D300A KLV 40V300A KLV 37M300A KLV 32D300A KLV 32V300A KLV 32M300A LCD Color TV This Wall Mount Bracket is designed for use with the specified products above For other TVs refer to their operating instructions to check if this Wall Mount Bracket can be used Some TVs are supplied with a leaflet explaining how to install the Wall Mount Bracket Installing the Wall Mount Bracket To Customers WARNING If the following precautions are not observed serious injury or death through fire electric shock the product toppling over or the product dropping can result Be sure to subcontract the installation to licensed contractors and keep small children away during the installation If the Wall Mount Bracket or the TV is not installed correctly the following accidents may occur Be sure licensed a contractors carry out installation The TV may fall and cause a serious injury such as a bruise or a fracture e If the wall on which the Wall Mount Bracket is installed is unstable uneven or not perpendicular to the floor the unit may fall and cause injury or property damage
14. orce the internal conductors may become exposed I and cause a short circuit or an electrical break This may cause a fire or an electric shock Be careful not to hurt your hands or fingers during the installation Be careful not to hurt your hands or fingers when installing the Wall Mount Bracket or the TV The screws needed to secure the Wall Mount Bracket to the wall are not supplied Use the appropriate screws for the wall material and structure when mounting the Wall Mount Bracket Before installation If you intend to install a TV that is not specified on page 2 be sure to refer to the leaflet Installing the Wall Mount Bracket supplied with your TV Step 1 Checking the parts required for the installation 1 Prepare four or more 8 mm diameter or equivalent screws not supplied and a screwdriver Select screws suitable for the material of the wall 2 Unpack the carton and check to see that all the following items are included Mounting Hook 2 o Screw PSW6 x 16 4 oS Hexagon wrench 1 Screw BVST4 x 12 6 5 GB Step 2 2 Referring to the Wall mounting dimensions diagram on page 13 Deciding on the determine the positions of the installation location screws for installing the Base Bracket 1 Referring to the TV installation The wall that the TV will be mounted on should be dimensions table on page 12 able to support a
15. r become damaged Lay the display face down on a stable and level surface with the Table Top Stand hanging over the edge of the surface Having the display face and the base of the Table Top Stand on the same level surface will create an unstable working condition and can damage the TV When detaching the Table Top Stand from the TV hold the Table Top Stand securely with both hands When using an electric screwdriver set the torque setting 3 Adjust the angle ofthe Mou nting to approximately 2 N m 20 kgf cm Do not lift the Mounting Hook before the screws two Hook using the supplied screws each for left right are secured This may distort hexagon wrench the Mounting Hook or the TV cabinet When installing the TV parallel to the wall 0 degrees adjustment of the Mounting Hook angle procedures and O below is not necessary Make sure that each 2 Referring to the Screw and Hook arm base amp is screwed in securely locations diagram table on page 1 3 determine the screw O Remove the two screws from the arm base of the positions and secure the Mounti ng Mounting Hook Choose the holes corresponding to Hook to the rear of the TV the desired angle 5 10 15 or 20 degrees 2 Adjust the angles of the top and bottom arm O Secure the Mounting Hook to the rear of the TV to fit the corresponding hole and firmly secure each temporarily using the supplied four screws PSW6 x 16 O Be sure that both
Download Pdf Manuals
Related Search