Operating Instructions - Manuals, Specs & Warranty
Contents
1. 8 Press the buttons to select Pitch and press the OK button The Pitch adjustment menu appears on the screen 9 Press the buttons until the vertical stripes disappear Adjust so that the vertical stripes disappear TTL Test Pate END II 10 Click END on the screen to turn off the test pattern 15 Adjust the picture s position manually H Center V Center If the picture is not in the center of the screen adjust the picture s centering as follows 1 Set the resolution to 1600 x 1200 on the computer 2 Load the Utility Disk 3 Start the Utility Disk and display the test pattern For Windows Click Utility Windows Win Utility exe For Macintosh Click Utility Mac Mac Utility 4 Press the MENU button The main menu appears on the screen 5 Press the 4 buttons to select amp INPUT SETTING and press the OK button The INPUT SETTING menu appears on the screen 6 Press the buttons to select H Center or V Center and press the OK button The H Center adjustment menu or V Center adjustment menu appears on the screen 7 Press the buttons to center the test pattern on the screen 8 Click END on the screen to turn off the test pattern 16 E Selecting the input priority2. HD15 HD15 video signal cable analog RGB supplied Connecting to a Macintosh to the HD 15 input connector analog RGB for INPUT1 or INPUT2 to the computer s output connector HD15 HD15 video signal cable analog RGB supplied Macintosh When connecting a Macintosh computer use an adapter not supplied if necessary Connect the adapter to the computer before connecting the video signal cable Setup 3 Connect the audio cord Connect the supplied audio cord to the monitor s corresponding audio input jack Using the monitor s speakers or headphones you can listen to sound from your computer or other audio equipment connected to the monitor s audio input jacks For more information see Controlling the volume on page 18 to the audio input for INPUT1 or INPUT2 to audio output of the computer or other audio equipment lt audio cord supplied Setup 4 Connect the power cord 1 Connect the supplied power cord to the monitor s AC IN connector 2 Connect it to a power outlet to power outlet lt power cord supplied 2 Setup 5 Bundle the cords and Setup 6 Turn on the monitor and cables computer 1 Remove the arm cover 1 Press the MAIN POWER switch on the right side of the monitor in the direction of
3. approx 45 approx 45 To use the monitor comfortably Adjust the viewing angle of your monitor according to the height of your desk and chair and so that light is not reflected from the screen to your eyes Note When adjusting the screen tilt and swivel proceed slowly and carefully being sure not to hit the monitor against the desk Grasp the sides of the LCD panel then adjust screen tilt Selecting the input signal INPUT button Press the INPUT button The input signal and corresponding input indicator change each time you press this button INPUT 10 20 INPUT1 Select the input signal received at the monitor s HD15 input connector for INPUT1 analog RGB INPUT2 Select the input signal received at the monitor s DVI D input connector digital RGB for INPUT2 or at the monitor s HD15 input connector analog RGB for INPUT2 When connecting computers to both of the monitor s video input connectors for INPUT2 DVI D and HD15 you can choose the connector to which a signal is input preferentially using Input2 Priority on the INPUT SETTING menu For more information about Input Priority see Selecting the input priority on page 16 Selecting the input signal for the audio input jack See Audio Select on page 17 Connecting Universal Serial Bus USB compliant peripherals The monitor has two upstream and two downstream USB connectors They provide a
4. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment NOTICE This notice is applicable for USA Canada only If shipped to USA Canada install only a UL LISTED CSA LABELLED power supply cord meeting the following specifications SPECIFICATIONS Plug Type Nema Plug 5 15p Cord Type SVT or SJT minimum 3 x 18 AWG Length Maximum 15 feet Rating Minimum 7 A 125 V NOTICE Cette notice s applique aux Etats Unis et au Canada uniquement Si cet appareil est export aux Etats Unis ou au Canada utiliser le cordon d alimentation portant la mention UL LISTED CSA LABELLED et remplissant les conditions suivantes SPECIFICATIONS Type de fiche Fiche Nema 5 15 broches Cordon Type SVT ou SJT minimum 3 x 18 AWG Longueur Maximum 15 pieds Tension Minimum 7 A 125 V ewe As an ENERGY STAR Partner Sony Corporation has determined that this product meets the ENERGY STAR Groggy guidelines for energy efficiency If you have any questions about this product you may call Sony Customer Information Center 1 800 222 SONY 7669 or write to Sony Customer Information Center 1 Sony Drive Mail Drop T1 11 Park Ridge NJ 07656 This monitor co
5. Japanese E Menu Lock Lock the control of buttons to prevent accidental adjustments or resetting 1 Press the buttons to select Menu Lock and press the OK button The options are displayed on the popup menu 2 Press the Y buttons to select either On or Off e On Only the power switch and INPUT button will operate If you attempt any other operation the On Menu Lock icon appears on the screen e Off Set Menu Lock to off If Menu Lock has been set to On when you press the MENU button Menu Lock is automatically selected E Reset Reset the adjustments to the default settings 1 Press the buttons to select Reset and press the OK button The options are displayed on the popup menu 2 Press the buttons to select the desired mode and press the OK button OK To reset all of the adjustment data to the default settings Note that the Language setting is not reset by this method e Cancel To cancel resetting and return to the menu screen 18 Technical Features Controlling the volume Using the monitor s speakers or headphones you can listen to sound from your computer or other audio equipment connected to the monitor s audio input jacks You can control the volume by using a separate Volume menu from the main menu 1 Press the buttons when no menu appears on the screen A Vome 3 E gt Ov 2 Press t
6. When connecting computers to both of the monitor s video input connectors for INPUT2 DVI D and HD15 you can choose the connector to which a signal is input preferentially INPUT SETTING O1 HDI5 ia 5 D Auto Adjust D Phase 20 Pitch 0 a a al EE H Center 50 cc V Center 50 ED Input2 Priority DVI D HD15 1600 x 1200 60 Hz Select Set Exit HEN 1 Press the MENU button The main menu appears on the screen 2 Press the buttons to select amp INPUT SETTING and press the OK button The INPUT SETTING menu appears on the screen 3 Press the buttons to select Input2 Priority and press the OK button The options are displayed on the popup menu 4 Press the buttons to select the desired mode DVI D The default setting The signal input to the DVI D input connector digital RGB for INPUT2 is displayed preferentially HD15 The signal input to the HD15 input connector analog RGB for INPUT2 is displayed preferentially If the monitor stays in the power saving mode and does not resume Carry out the following procedures if the monitor stays in the power saving mode and does not resume when the computer being activated is connected to a video input connector for INPUT2 other than the one selected in Input2 Priority 1 Press the 5 power switch An INFORMATION message No input signal appears on the screen 2 Press the MENU button while the
7. xxx Hz If xxx x kHz xxx Hz is displayed This indicates that either the horizontal or vertical frequency is not supported by the monitor s specifications The figures indicate the horizontal and vertical frequencies of the current input signal If Resolution too high Set to 1600x1200 is displayed This indicates that the resolution is not supported by the monitor s specifications 1600 x 1200 or less If No input signal appears on the screen This indicates that no signal is being input via the currently selected connector INFORMATION 1 HD15 No input signal Go to power save EE _ gt _ E Go to power save The monitor will enter the power saving mode after about 5 seconds from the time the message is displayed 20 If Cable disconnected appears on the screen This indicates that the video signal cable has been disconnected from the currently selected connector INFORMATION 1 HD15 Cable disconnected Go to power save R E Go to power save The monitor will enter the power saving mode after about 5 seconds from the time the message is displayed Trouble symptoms and remedies If a problem occurs as a result of a connected computer or other equipment refer to the connected computer equipment s instruction manual Use the self diagnosis function page 23 if the following recommendations do not resolve the problem Symptom Che
8. INFORMATION message is being displayed The Input2 Priority screen from the INPUT SETTING menu appears on the screen 3 Press the buttons to select the input you want to display on the screen OPTION menu You can adjust the following items using the OPTION menu Zoom Sk OPTION C OTHDS Menu Position als Zoom Full2 e Audio Select 75 _ Menu Position Audio Select Auto P USB Select Auto Language English Menu Lock Off Reset e USB Select e Language Menu Lock Reset ro 1600 x 1200 60 Hz Select SHC Ext 1 Press the MENU button The main menu appears on the screen 2 Press the Y buttons to select OPTION and press the OK button The OPTION menu appears on the screen 3 Press the buttons to select the desired item and press the OK button Adjust the selected item according to the following instructions E Zoom The monitor is set to display the picture on the screen in full irrespective of the picture s mode or resolution in the default setting Full2 You can also view the picture in its actual aspect ratio or resolution 1 Press the buttons to select Zoom and press the OK button The options are displayed on the popup menu 2 Press the buttons to select the desired mode Full2 The default setting The input signal is displayed on the screen in full irrespective of the picture s mode or resolution e Full1 The i
9. Stereo minijack 0 5 Vrms 47 kQ 100 240 V 50 60 Hz Max 1 0A Max 80 W 5 35 C Dimensions width height depth Mass Plug amp Play Accessories Display upright Approx 520 x 472 x 256 mm 20 l2 x 18 3 8 x 10 1 8 inches with stand Approx 520 x 410 x 98 mm 20 1 2 x 16 4x 3 1 8 inches without stand Approx 12 0 kg 26 lb 7 oz with stand Approx 9 5 kg 20 Ib 15 oz without stand DDC2B See page 7 Recommended horizontal and vertical timing condition e Horizontal sync width duty should be more than 4 8 of total horizontal time or 0 8 us whichever is larger e Horizontal blanking width should be more than 2 5 psec e Vertical blanking width should be more than 450 usec Design and specifications are subject to change without notice 24
10. The PICTURE ADJUSTMENT menu appears on the screen Contrast 50 Cr 3 Press the buttons to select Color and press the OK button 1 Press the MENU button The options are displayed on the popup menu The main menu appears on the screen 4 Press the buttons to select the desired color 2 Press the Y buttons to select PICTURE temperature ADJUSTMENT and press the OK button Since the default setting is 9300K the whites will change The PICTURE ADJUSTMENT menu appears on the screen from a bluish hue to a reddish hue as the temperature is lowered to 6500K and 5000K 3 Press the buttons to select Contrast and press the OK button The Contrast adjustment menu appears on the screen 4 Press the buttons to adjust the contrast 13 Fine tuning the color temperature The setting is stored in memory for INPUT1 INPUT2 DVI D and INPUT2 HD15 respectively gt EH 0 a G 128 a B 140 Sa 1 Press the MENU button The main menu appears on the screen 2 Press the t buttons to select PICTURE ADJUSTMENT and press the OK button The PICTURE ADJUSTMENT menu appears on the screen 3 Press the buttons to select Color and press the OK button The options are displayed on the popup menu 4 Press the buttons to select Adjust and press the OK button The fine tuning menu for color temperature appears on the screen 5 Press the buttons to selec
11. fast and easy way to connect USB compliant peripheral devices such as keyboards mice printers and scanners to your computer using a standardized USB cable To use the monitor as a hub for your peripheral devices connect the USB devices as follows Turn on the monitor and computer s Connect your computer s to the upstream connectors using the supplied USB cable For customers using Windows If a message appears on your screen follow the on screen instructions and select a generic USB hub driver Connect your USB compliant peripheral devices to the downstream connectors For customers using a Macintosh computer with a keyboard having a power button When you connect a Macintosh keyboard with a power button to the USB downstream connector the power button on the keyboard does not function To turn your Macintosh computer on use the power button on the computer or connect the keyboard to the computer directly and turn the computer on then disconnect the keyboard and re connect it to the monitor Notes Not all computers and or operating systems support USB configurations Check your computer s instruction manual to see if you can connect USB devices In most cases USB driver software needs to be installed on the host computer Refer to the peripheral device s instruction manual for further details When you connect a computer whose power is already connected to the USB upstream connector on the monitor the monitor wi
12. stored on magnetic tapes and discs Note on the LCD Liquid Crystal Display Please note that the LCD screen is made with high precision technology However black points or bright points of light red blue or green may appear constantly on the LCD screen and irregular colored stripes or brightness may appear on the LCD screen This is not malfunction Effective dots more than 99 99 Maintenance Be sure to unplug the power cord from the power outlet before cleaning your monitor Clean the LCD screen with a soft cloth If you use a glass cleaning liquid do not use any type of cleaner containing an anti static solution or similar additive as this may scratch the LCD screen s coating Clean the cabinet panel and controls with a soft cloth lightly moistened with a mild detergent solution Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzine Do not rub touch or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver This type of contact may result in a scratched picture tube Note that material deterioration or LCD screen coating degradation may occur if the monitor is exposed to volatile solvents such as insecticide or if prolonged contact is maintained with rubber or vinyl materials Transportation Disconnect all cables from the monitor and grasp the support and base sections of the display stand firmly with both hands when transporti
13. the ECO button ECO mode On The ECO mode On menu appears on the screen and the backlight level is reduced The menu automatically disappears after about 5 seconds To cancel the ECO mode Press the ECO button again ECO mode Off The ECO mode Off menu appears on the screen and normal backlight level is set The menu automatically disappears after about 5 seconds Automatic picture quality adjustment function analog RGB signal only When the monitor receives an input signal it automatically adjusts the picture s position and sharpness phase pitch and ensures that a clear picture appears on the screen The factory preset mode When the monitor receives an input signal it automatically matches the signal to one of the factory preset modes stored in the monitor s memory to provide a high quality picture at the center of the screen If the input signal matches the factory preset mode the picture appears on the screen automatically with the appropriate default adjustments If input signals do not match one of the factory preset modes When the monitor receives an input signal that does not match one of the factory preset modes the automatic picture quality adjustment function of this monitor is activated to ensure that a clear picture always appears on the screen within the following monitor frequency ranges Horizontal frequency 28 92 kHz Vertical frequency 48 85 Hz Co
14. Contrast 50 a Brightness 50 em E Color 9300K E Gamma Gamma2 Smoothing Text Standard Graphics 1600 x 1200 60 Hz Select 00 Set Exit MENU 1 Press the MENU button The main menu appears on the screen 2 Press the Y buttons to select PICTURE ADJUSTMENT and press the OK button The PICTURE ADJUSTMENT menu appears on the screen 3 Press the t buttons to select Smoothing and press the OK buiton The options are displayed on the popup menu 4 Press the Y buttons to select the desired mode The smoothing effect becomes stronger in the order of Text gt Standard gt Graphics Text To make the characters appear clear and sharp This mode is suited for text based applications e Standard The default setting Standard smoothing effect e Graphics To make the pictures appear clean This mode is suited for CD ROM software for photo images or illustrations Notes When you set Zoom on the OPTION menu to Real Smoothing is not available e 1600 x 1200 resolution signals are shown only in the Real mode and Smoothing is not possible D INPUT SETTING menu You can adjust the following items using the INPUT SETTING menu e Auto Adjust INPUT SETTING er HDS e D 3 Phase Auto Adjust e Pitch Phase 20 mms mue Sai Pitch 0 CE H Center 2 H center 50 a VC V Center 5 enter Input2 Priority DVI D
15. ICTURE ADJUSTMENT menu appears on the screen Select SHC Exit 3 Press the f buttons to select Brightness and E Adjusting the Backlight press the OK button If the screen is too bright adjust the backlight to make the screen The Brightness adjustment menu appears on the screen easier to see 4 Press the buttons to adjust the brightness Note pan cannot be adjusted when the ECO mode is set to On w Adjusting the Color You can select the picture s color level for the white color field Bacione 460 from the default color temperature settings Also if necessary you can fine tune the color temperature PICTURE ADJUSTMENT 1 HD15 1 Press the MENU button ee The main menu appears on the screen 2 RC n a E 9300K 2 Press the buttons to select PICTURE L smono soon ADJUSTMENT and press the OK button E Casal The PICTURE ADJUSTMENT menu appears on the screen a _ ea 3 Press the buttons to select Backlight and press the OK button Selecting the picture s color level for the white color The Backlight adjustment menu appears on the screen field from the default color temperature settings 4 Press the buttons to adjust the light level 1 Press the MENU button The main menu appears on the screen E Adjusting the Contrast Adjust the picture contrast 2 Press the Y buttons to select PICTURE ADJUSTMENT and press the OK button
16. NPUT button page 11 e If Cable disconnected appears on the screen Check that the video signal cable is properly connected Check that the input signal setting is correct by pressing the INPUT button page 11 If Not supported signal appears on the screen reconnect the old monitor Then adjust the computer s graphics board within the following ranges Analog RGB Digital RGB Horizontal 28 92 kHz 28 75 kHz frequency Vertical 48 85 Hz 60 Hz frequency Resolution 1600 x 1200 or less 1600 x 1200 or less For more information about on screen messages see Trouble symptoms and remedies on page 21 No need for specific drivers The monitor complies with the DDC Plug amp Play standard and automatically detects all the monitor s information No specific driver needs to be installed on the computer The first time you turn on your computer after connecting the monitor the setup Wizard may appear on the screen In this case follow the on screen instructions The Plug amp Play monitor is automatically selected so that you can use this monitor The vertical frequency is set to 60 Hz Since flickers are unobtrusive on the monitor you can use it as it is You do not need to set the vertical frequency to any particular high value 10 Setup 7 Adjust the tilt and swivel This monitor can be adjusted within the angles shown below approx 5 approx 20 TAA
17. SONY Ee TFT LCD Color Computer Display Operating Instructions SDM X202 2002 Sony Corporation Owner s Record The model and serial numbers are located at the rear of the unit Record these numbers in the spaces provided below Refer to them whenever you call upon your dealer regarding this product Model No Serial No To prevent fire or shock hazard do not expose the unit to rain or moisture Dangerously high voltages are present inside the unit Do not open the cabinet Refer servicing to qualified personnel only FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver
18. Technical Features 18 Controlling the volume 18 Power saving function 19 Reducing the power consumption ECO mode 19 Automatic picture quality adjustment function analog RGB signal only 19 Troubleshooting 20 On screen messages 20 Trouble symptoms and remedies 21 Self diagnosis function 23 Specifications 55e due vine ne tomes 24 Precautions Warning on power connections Use the supplied power cord If you use a different power cord be sure that it is compatible with your local power supply For the customers in the U S A If you do not use the appropriate cord this monitor will not conform to mandatory FCC standards For the customers in the UK If you use the monitor in the UK be sure to use the appropriate UK power cord Example of plug types for 100 to 120 V AC for 200 to 240 VAC for 240 V AC only The equipment should be installed near an easily accessible outlet Installation Do not install or leave the monitor In places subject to extreme temperatures for example near a radiator heating vent or in direct sunlight Subjecting the monitor to extreme temperatures such as in an automobile parked in direct sunlight or near
19. a heating vent could cause deformations of the casing or malfunctions In places subject to mechanical vibration or shock Near any equipment that generates a strong magnetic field such as a TV or various other household appliances In places subject to inordinate amounts of dust dirt or sand for example near an open window or an outdoor exit If setting up temporarily in an outdoor environment be sure to take adequate precautions against airborne dust and dirt Otherwise irreparable malfunctions could occur Handling the LCD screen Do not leave the LCD screen facing the sun as it can damage the LCD screen Take care when you place the monitor by a window Do not push on or scratch the LCD screen Do not place a heavy object on the LCD screen This may cause the screen to lose uniformity or cause LCD panel malfunctions If the monitor is used in a cold place a residual image may appear on the screen This is not a malfunction The screen returns to normal as the temperature rises to a normal operating level If a still picture is displayed for a long time a residual image may appear for a while The residual image will eventually disappear The LCD panel becomes warm during operation This is not a malfunction About the built in stereo speakers Be sure to keep magnetic recording equipment tapes and floppy discs away from the speaker s opening as the speakers generate a magnetic field This magnetic field may affect data
20. aused by the monitor The computer is in the power saving mode Try pressing any key on the keyboard or moving the mouse Check that your graphics board is installed properly Check that the computer s power is on If Not supported signal appears on the screen page 20 Problem caused by a connected computer or other equipment and not caused by the monitor Check that the video frequency range is within that specified for the monitor If you replaced an old monitor with this monitor reconnect the old monitor and adjust the computer s graphics board within the following ranges Horizontal frequency 28 92 kHz analog RGB 28 75 kHz digital RGB Vertical frequency 48 85 Hz analog RGB 60 Hz digital RGB Resolution 1600 x 1200 or less If using Windows If you replaced an old monitor with this monitor reconnect the old monitor and do the following Select SONY from the Manufacturers list and select SDM X202 from the Models list in the Windows device selection screen If SDM X202 does not appear in the Models list try Plug amp Play If using a Macintosh system When connecting a Macintosh computer use an adapter not supplied if necessary Connect the adapter to the computer before connecting the video signal cable 21 Symptom Check these items Picture flickers bounces oscillates or is scrambled e Adjust the pitch and phase analog RGB s
21. ck these items No picture If the power indicator is not lit or if the power indicator will not light up when the 5 power switch is pressed Check that the power cord is properly connected Check that the monitor s MAIN POWER switch is on page 9 If the power indicator turns on in red Check that the power switch is on If the power indicator is green Use the self diagnosis function page 23 If Cable disconnected appears on the screen Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets page 7 Check that the video input connector s pins are not bent or pushed in Check that the input select setting is correct page 11 A non supplied video signal cable is connected If you connect a non supplied video signal cable Cable disconnected may appear on the screen before entering the power saving mode This is not a malfunction If No input signal appears on the screen or the power indicator is orange e Check that the input priority setting is correct page 16 Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets page 7 Check that the video input connector s pins are not bent or pushed in Check that the input select setting is correct page 11 GB Problem caused by a connected computer or other equipment and not c
22. e Input2 Priority 1600 x 1200 60 Hz Select SHC Exit E Adjusting Picture Position and Sharpness analog RGB signal only Note When receiving digital RGB signals from the DVI D input connector for INPUT2 adjustment is unnecessary Automatic picture quality adjustment function When the monitor receives an input signal it automatically adjusts the picture s position and sharpness phase pitch and ensures that a clear picture appears on the screen page 19 Note While the automatic picture quality adjustment function is activated only the power switch will operate If the automatic picture quality adjustment function of this monitor seems to not completely adjust the picture You can make further automatic adjustment of the picture quality for the current input signal See Auto Adjust below If you still need to make further adjustments to the picture quality You can manually adjust the picture s sharpness phase pitch and position horizontal vertical position These adjustments are stored in memory and automatically recalled when the monitor receives a previously input and registered input signal Make further automatic adjustments to the picture quality for the current input signal Auto Adjust 1 Press the MENU button The main menu appears on the screen 2 Press the buttons to select amp INPUT SETTING and press the OK bution The INPUT SETTING menu appears on the scre
23. en 3 Press the buttons to select Auto Adjust and press the OK button The options are displayed on the popup menu 4 Press the buttons to select OK and press the OK button Make the appropriate adjustments of the screen s phase pitch and horizontal vertical position for the current input signal and store them Adjust the picture s sharpness manually Phase Pitch You can adjust the picture s sharpness as follows This adjustment is effective when the computer is connected to the monitor s HD15 input connector analog RGB 1 Load the Utility Disk 2 Start the Utility Disk and display the test pattern For Windows Click Utility Windows Win Utility exe For Macintosh Click Utility Mac Mac Utility 3 Press the MENU button The main menu appears on the screen 4 Press the buttons to select amp INPUT SETTING and press the OK button The INPUT SETTING menu appears on the screen 5 Press the t buttons to select Phase and press the OK bution The Phase adjustment menu appears on the screen 6 Press the buttons until the horizontal stripes are at a minimum Adjust so that the horizontal stripes are at a minimum mana tf 7 Press the OK button The main menu appears on the screen If vertical stripes are observed over the entire screen adjust the pitch using the following procedures
24. g the computer to the monitor s HD15 input connector analog RGB refer to Setup 2 Connect a computer equipped with an HD15 output connector analog RGB Note Do not touch the pins of the video signal cable connector as this might bend the pins 1 Remove the back cover 2 Using the supplied DVI D video signal cable digital RGB connect the computer to the monitor s DVI D input connector digital RGB for INPUT2 to the DVI D input connector digital RGB for INPUT2 to the computer s DVI output connector digital RGB DVI D video signal cable digital RGB supplied Setup 2 Connect a computer equipped with an HD15 output connector analog GE m Turn off the monitor and computer before connecting them Note Do not touch the pins of the video signal cable connector as this might bend the pins 1 Remove the back cover continued 7 2 Using the supplied HD15 HD15 video signal cable analog RGB connect the computer to the monitor s HD 15 input connector analog RGB for INPUT 1 or INPUT2 Connect the computer according to the following illustrations Connecting to an IBM PC AT or compatible computer to the HD 15 input connector analog RGB for INPUT1 or INPUT2 to the computer s HD15 output connector analog RGB g Gu IBM PC AT or compatible computer
25. he buttons to control the volume The menu automatically disappears after about 5 seconds Using the headphones By connecting your headphones to the monitor s headphones jack you can listen to sound from your computer or other audio equipment connected to the monitor s audio input jack Notes e You cannot adjust the volume when the main menu is displayed on the screen e When your monitor is in power saving mode no sound comes from the speakers or the headphones Power saving function This monitor meets the power saving guidelines set by VESA ENERGY STAR and NUTEK If the monitor is connected to a computer or video graphics board that is DPMS Display Power Management Signaling compliant the monitor will automatically reduce power consumption as shown below Power mode Power consumption power indicator normal 80 W max green operation active off approx 1 W orange deep sleep power off approx 1 W red main power off 0 W off When your computer enters the active off mode the input signal is cut and No input signal appears on the screen After 20 seconds the monitor enters the power saving mode Deep sleep is a power saving mode defined by the Environmental Protection Agency Reducing the power consumption ECO mode If you press the ECO button on the front of the monitor the backlight level and the power consumption are reduced Press
26. he video input signal between INPUT 1 and INPUT2 when two computers are connected to the monitor and the corresponding indicator INPUT1 or INPUT2 lights up 6 ECO button page 19 This button is used to reduce the power consumption Stereo speakers page 18 These speakers output the audio signals as sound MAIN POWER switch page 9 This switch turns the monitor s main power on and off 9 Back cover page 7 Remove this cover when you connect cables or cords Headphones jack page 18 This jack outputs audio signals to the headphones continued 5 Rear of the LCD display 11 AC IN connector page 8 This connector connects the power cord supplied 2 Security Lock Hole The security lock hole should be used with the Kensington Micro Saver Security System Micro Saver Security System is a trademark of Kensington 13 Audio input jack for INPUT1 page 8 This jack inputs audio signals when connected to the audio output jack of a computer or other audio equipment Audio input jack for INPUT2 page 8 This jack inputs audio signals when connected to the audio output jack of a computer or other audio equipment 15 DVI D input connector digital RGB for INPUT2 page 7 This connector inputs digital RGB video signals that comply with DVI Rev 1 0 HD15 input connector analog RGB for INPUT1 page 7 This connector inputs ana
27. ignal only page 15 e Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors laser printers electric fans fluorescent lighting or televisions Move the monitor away from power lines or place a magnetic shield near the monitor e Try plugging the monitor into a different AC outlet preferably on a different circuit e Change the orientation of the monitor Problem caused by a connected computer or other equipment and not caused by the monitor e Check your graphics board manual for the proper monitor setting e Confirm that the graphics mode VESA Macintosh 19 Color etc and the frequency of the input signal are supported by this monitor Even if the frequency is within the proper range some graphics boards may have a sync pulse that is too narrow for the monitor to sync with correctly e This monitor does not process interlace signals Set for progressive signals e Adjust the computer s refresh rate vertical frequency to obtain the best possible picture 60 Hz is recommended Picture is fuzzy e Adjust the brightness and contrast page 13 e Adjust the pitch and phase analog RGB signal only page 15 Problem caused by a connected computer or other equipment and not caused by the monitor e Set the resolution to 1600 x 1200 on your computer Picture is ghosting Eliminate the use of video cable extensions and or video switch boxes e Check that all plugs are f
28. irmly seated in their sockets Picture is not centered or sized properly analog RGB signal only e Adjust the pitch and phase page 15 e Adjust the picture position page 16 Note that some video modes do not fill the screen to the edges Picture is too small e Set the zoom setting to Full2 page 17 Problem caused by a connected computer or other equipment and not caused by the monitor e Set the resolution to 1600 x 1200 on your computer Picture is dark e Adjust the brightness page 13 e Adjust the backlight page 13 e It takes a few minutes for the display to become bright after turning on the monitor e Adjust the gamma using Gamma on the PICTURE ADJUSTMENT menu page 14 If you press the ECO button the screen turns darker Wavy or elliptical pattern moire is visible e Adjust the pitch and phase analog RGB signal only page 15 Color is not uniform e Adjust the pitch and phase analog RGB signal only page 15 White does not look white e Adjust the color temperature page 13 Monitor buttons do not operate Om appears on the screen If Menu Lock on the OPTION menu is set to On set it to Off page 18 Resolution displayed on the menu screen is incorrect Depending on the graphics board setting the resolution displayed on the menu screen may not coincide with the one set on the computer After turnig off the
29. ll not enter the power saving mode When the monitor is in the power saving mode USB peripheral devices will not function To resume the use of USB peripheral devices cancel the mode by pressing the D power switch If the peripheral devices do not function properly confirm that the upstream input setting in USB Select on the OPTION menu is correct page 17 If you connect a keyboard or mouse to the USB connectors and then boot your computer for the first time the peripheral devices may not function First connect the keyboard and mouse directly to the computer and set up the USB compliant devices Then connect them to this monitor When you connect peripheral devices to the downstream connectors be sure not to lean on the display Otherwise the display may incline and catch your fingers The number of USB hubs that can be connected together is defined as up to six tiers by USB specifications Two tiers of a USB hub are built into the monitor Therefore you are allowed to connect four more tiers of a USB hub together This monitor does not support the USB 2 0 standard 11 Customizing Your Monitor Before making adjustments Connect the monitor and the computer and turn them on For the best results wait for at least 30 minutes before making adjustments You can make numerous adjustments to your monitor using the on screen menu Navigating the menu 1 Display the main menu Press the MENU b
30. log RGB video signals 0 700 Vp p positive and sync signals HD15 input connector analog RGB for INPUT2 page 7 This connector inputs analog RGB video signals 0 700 Vp p positive and sync signals USB Universal Serial Bus downstream connectors page 11 These connectors are used to connect the monitor to USB compliant peripheral devices USB Universal Serial Bus upstream connector for INPUT1 page 11 This connector is used to connect the monitor to a USB compliant computer USB Universal Serial Bus upstream connector for INPUT2 page 11 This connector is used to connect the monitor to a USB compliant computer 21 Cable holder page 9 This part secures cables and cords to the monitor 22 Arm cover page 9 Remove this cover to bundle connecting cords and cables 23 Latch page 9 This part secures cables and cords to the monitor Setup Before using your monitor check that the following items are included in your carton LCD display e Power cord HD15 HD15 video signal cable analog RGB DVI D video signal cable digital RGB e Audio cord stereo miniplug e USB upstream cable e Utility Instruction Manual CD ROM utility software for Windows Macintosh Operating Instructions e Warranty card e Quick Setup Guide Setup 1 Connect a computer equipped with a DVI output connector digital RGB Turn off the monitor and computer before connecting them When connectin
31. main power the power indicator stays bright for a while 22 e When the main power is on but the power switch is not pressed or when the monitor is in the power saving mode if you turn the MAIN POWER switch off the power indicator may not turn off right away This is not a malfunction Displaying this monitor s information While the monitor is receiving a video signal press and hold the MENU button for more than 5 seconds until the information box appears Press the MENU button again to make the box disappear Example Model name INFORMATION 1 HD15 Model SONY SDM X202 Serial Ser No 1234567 number Manufactured 2002 40 ae Week and year of manufacture MENU If any problem persists call your authorized Sony dealer and give the following information Model name SDM X202 e Serial number Detailed description of the problem Date of purchase Name and specifications of your computer and graphics board Type of input signals analog RGB digital RGB Self diagnosis function This monitor is equipped with a self diagnosis function If there is a problem with your monitor or computer s the screen will go blank and the power indicator will light up green If the power indicator is lit in orange the computer is in power saving mode Try pressing any key on the keyboard or moving the mouse power indicator If the picture disappears fr
32. mplies with the TCO 99 guidelines for the gray model Declaration of Conformity Trade Name SONY Model No SDM X202 Responsible Party Sony Electronics Inc Address 680 Kinderkamack Road Oradell NJ 07649 USA Telephone No 201 930 6972 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This monitor complies with the TCO 95 guidelines for the black model Table of Contents Macintosh is a trademark licensed to Apple Computer Inc registered in the U S A and other countries Windows is registered trademark of Microsoft Corporation in the United States and other countries IBM PC AT and VGA are registered trademarks of IBM Corporation of the U S A VESA and DDC are trademarks of the Video Electronics Standards Association ENERGY STAR is a U S registered mark Adobe and Acrobat are trademarks of Adobe Systems Incorporated All other product names mentioned herein may be the trademarks or registered trademarks of their respective companies Furthermore TV and are not mentioned in each case in this manual http Awww sony net PRECAUTIONS Les nee detente acta Seren te nt ate tamer 4 Identifying parts and c
33. ng If you drop the monitor you may be injured or the monitor may be damaged When you transport this monitor for repair or shipment use the original carton and packing materials Disposal of the monitor Do not dispose of this monitor with general household waste The fluorescent tube used in this monitor contains mercury Disposal of this monitor must be carried out in accordance to the regulations of your local sanitation authority Identifying parts and controls See the pages in parentheses for further details Front of the LCD display O ol of ol fe fe O Side view of the LCD display Rear of the display stand 1 Power switch and 5 power indicator pages 9 19 23 This switch turns the monitor on when the power indicator lights up in red To turn the monitor off press this switch again If the power indicator does not light up press the MAIN POWER switch 8 2 MENU button page 12 This button turns the menu screen on and off 3 t and 1 volume control buttons pages 12 18 GB These buttons are used to select the menu items and make adjustments and also display the Volume menu to control the volume 4 OK button page 12 This button activates the selected menu item and adjustments made using the 4 4 buttons 3 5 INPUT button and INPUT1 INPUT2 indicators page 11 This button switches t
34. nput signal is displayed on the screen at its actual aspect ratio Therefore black bands may appear at the top and bottom of the picture depending on the signal e Real The input signal is displayed on the screen at its actual resolution Sub 1600 x 1200 signals are displayed at the center of the screen surrounded by a black frame Note When you use 1600 x 1200 resolution signals the above mentioned settings are not available The picture is displayed on the screen in full E Menu Position You can change the menu position if it is blocking an image on the screen 1 Press the buttons to select Menu Position and press the OK button The Menu Position adjustment menu appears on the screen 2 Press the buttons to select the desired position You can choose one of 9 positions where the menu will appear E Audio Select Select the audio input when connecting to both of the monitor s audio input jacks for INPUT1 and INPUT2 1 Press the buttons to select Audio Select and press the OK button The options are displayed on the popup menu 2 Press the buttons to select the desired mode e Auto The default setting To select either audio input by switching with the INPUT button e Input1 To select the audio input from the AUDIO jack e Input2 To select the audio input from the AUDIO2 jack E USB Select This monitor is equipped with two USB upstream connectors The effective upstream inpu
35. nsequently the first time the monitor receives input signals that do not match one of the factory preset modes the monitor may take a longer time than normal to display the picture on the screen This adjustment data is automatically stored in memory so that next time the monitor will function in the same way as when the monitor receives the signals that match one of the factory preset modes If you adjust the phase pitch and picture position manually For some input signals the automatic picture quality adjustment function of this monitor may not completely adjust the picture position phase and pitch In this case you can set these adjustments manually page 15 If you set these adjustments manually they are stored in memory as user modes and automatically recalled whenever the monitor receives the same input signals 19 Troubleshooting Before contacting technical support refer to this section On screen messages If there is something wrong with the input signal one of the following messages appears on the screen To solve the problem see Trouble symptoms and remedies on page 21 If Not supported signal appears on the screen This indicates that the input signal is not supported by the monitor s specifications Check the following items For more information about on screen messages see Trouble symptoms and remedies on page 21 INFORMATION 1 HD15 Not supported signal XXX X KHz
36. om the screen and the power indicator is green 1 Turn off the power switch and disconnect the video signal cables from the monitor 2 Turn the monitor on by pressing the 5 power switch If all four color bars appear white red green blue the monitor is working properly Reconnect the video input cables and check the condition of your computer s If the color bars do not appear there is a potential monitor failure Inform your authorized Sony dealer of the monitor s condition If the power indicator lights up in orange Try pressing any key on the keyboard or moving the mouse The computer s power saving mode is shut off and the power indicator lights up in green and the picture appears on the screen 23 Specifications LCD panel Input signal format Resolution Input signal levels Audio output Headphones jack Audio signal Power requirements Power consumption Operating temperature Panel type a Si TFT Active Matrix Picture size 20 1 inch RGB operating frequency Horizontal 28 92 kHz analog RGB 28 75 kHz digital RGB Vertical 48 85 Hz analog RGB 60 Hz digital RGB Horizontal Max 1600 dots Vertical Max 1200 lines Analog RGB video signal 0 7 Vp p 75 Q positive SYNC signal TTL level 2 2 kQ positive or negative Separate horizontal and vertical or composite sync 0 3 Vp p 75 Q negative Sync on green Digital RGB DVD signal TMDS Single link 1Wx2
37. ontrols 5 SQUID siimi ii Eet arena essences nue 7 Setup 1 Connect a computer equipped with a DVI output connector digital RGB 7 Setup 2 Connect a computer equipped with an HD15 output connector analog RGB 7 Setup 3 Connect the audio cord 8 Setup 4 Connect the power cord 8 Setup 5 Bundle the cords and cables 9 Setup 6 Turn on the monitor and computer 9 Setup 7 Adjust the tilt and swivel 10 Selecting the input signal INPUT button 11 Connecting Universal Serial Bus USB compliant peripherals 11 Customizing Your Monitor 12 Navigating the menu PICTURE ADJUSTMENT menu 18 Adjusting the Backlight 13 Adjusting the Contrast 13 Adjusting the Brightness 13 Adjusting the Color 13 Selecting the Gamma 14 Selecting the Smoothing 14 S D INPUT SETTING Menu seras sence Dieter are hess 15 Adjusting Picture Position and Sharpness analog RGB signal only 15 Selecting the input priority 16 OPTION menu AL Au etch igs Ree nn nd sn 17
38. t R Red or B Blue and press the OK button Then press the Y buttons to adjust the color temperature and press the OK button Since this adjustment changes the color temperature by increasing or decreasing the R and B components with respect to G green the G component is fixed 6 Press the buttons to select then press the OK button The new color setting is stored in memory and automatically recalled whenever User is selected The PICTURE ADJUSTMENT menu appears on the screen E Selecting the Gamma You can associate the picture s color shade on the screen with the picture s original color shade PICTURE ADJUSTMENT HD EN gt Backlight 100 3 gt 2 Contrast 50 a A Brightness 50 SS KA Color 9300K Gamma1 Smoothing Gamma2 Gamma3 1600 x 1200 60 Hz Select Se Ext 1 Press the MENU button The main menu appears on the screen 2 Press the t buttons to select PICTURE ADJUSTMENT and press the OK button The PICTURE ADJUSTMENT menu appears on the screen 3 Press the buttons to select Gamma and press the OK bution The options are displayed on the popup menu 4 Press the buttons to select the desired mode 14 E Selecting the Smoothing If the picture displayed at the Full2 or Full1 mode of Zoom is not smooth use the picture smoothing function PICTURE ADJUSTMENT C 1 HD15 ej Backlight 100 C ZD
39. t switches depending on this item setting 1 Press the buttons to select USB Select and press the OK button The options are displayed on the popup menu 2 Press the buttons to select the desired mode e Auto The default setting To select either upstream input by switching with the INPUT button e Input1 To select the upstream input from the USB connector for INPUT1 e Input2 To select the upstream input from the USB connector for INPUT2 Notes e When you set this item to either Input or Input2 the upstream input does not switch even if the video input is switched with the INPUT button If you want to link the upstream input to switching with the INPUT button set the item to Auto e When you connect devices that require prolonged data communication with the computer such as a printer or a scanner to a downstream connector on this monitor set this item to either Input or Input2 Otherwise the data communication with the computer may be interrupted each time you press the INPUT button and a failure of the printing or scanning may occur 17 M Language 1 Press the buttons to select Language and press the OK button The options are displayed on the popup menu 2 Press the buttons to select a language English e Fran ais French e Deutsch German e Espa ol Spanish e Italiano Italian e Nederlands Dutch e Svenska Swedish e Pycckun Russian HAE
40. the I 2 Secure the video signal cable and audio cord using The power indicator lights up in red the cable holder on the cabinet 3 Bundle all of the cords and cables inside of the stand MAIN POWER 4 Engage the latch on the stand as illustrated below to hold the cords and cables Al gt F 5 Replace the arm cover and back cover lights in red arm cover 2 Press the power switch on the front right of the monitor The power indicator lights up in green J lights in green 3 Turn on the computer 4 Press the INPUT button to select the desired input signal The selected input signal indicator lights up and the picture appears on the screen Note For more information see Selecting the input signal INPUT If you cannot bundle all of the cords and cables inside the stand leave button on page 11 them hanging down outside the stand INPUT 10 20 The installation of your monitor is complete If necessary use the monitor s controls to adjust the picture page 12 If no picture appears on your screen e Check that the power cord and the video signal cable are properly connected If No input signal appears on the screen Check that the input priority setting is correct page 16 The computer is in the power saving mode Try pressing any key on the keyboard or moving the mouse Check that the input signal setting is correct by pressing the I
41. utton to display the main menu on your screen MENU 2 Select the menu Press the buttons to display the desired menu Press the OK button to move to the first menu item A p OK O 3 Select the item you want to adjust Press the buttons to select the item you want to adjust then press the OK button Ae O 4 Adjust the item Press the buttons to make the adjustment then press the OK button When you press the OK button the setting is stored then the display returns to the previous menu O K A O OV 12 5 Close the menu Press the MENU button once to return to normal viewing If no buttons are pressed the menu closes automatically after about 45 seconds MENU E Resetting the adjustments to the default settings You can reset the adjustments using Reset on the OPTION menu For more information about resetting the adjustments see Reset on page 18 E Adjusting the Brightness ES PICTU RE ADJ USTM ENT menu Adjust the picture brightness black level You can adjust the following items using the PICTURE ADJUSTMENT menu Backlight Brightness 50 Coa PICTURE ADJUSTMENT 1 HD15 Contrast ey PRE 1 Press the MENU button e Brightness ED Contest so c The main menu appears on the screen Color A Seo ik Gamma D Saver 2 Press the buttons to select PICTURE Smoothing _ ADJUSTMENT and press the OK button _ 1600 x 1200 60 Hz The P
Download Pdf Manuals
Related Search