PROFESSIONAL GLASSWASHER
Contents
1. 29 SMEG thanks you for choosing one of its products Read all the instructions in this manual carefully to become familiar with the right conditions for the proper use of your glasswasher TECHNICAL INSTRUCTIONS These are intended for the qualified staff who are to install commission and test the appliance and carry out any servicing and repairs These provide recommendations for use a description of the controls and the correct procedures for cleaning and maintaining the glasswasher egge Smeg 1 PRECAUTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE GLASSWASHER AND MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE APPLIANCE POSITIONING HOOKUP COMMISSIONING TROUBLESHOOTING AND REPLACING THE POWER CABLE MUST ALWAYS BE CARRIED OUT BY QUALIFIED STAFF Ail THE APPLIANCE MUST BE GROUNDED AS REQUIRED BY ELECTRICAL EQUIPMENT SAFETY STANDARDS THE GLASSWASHER IS INTENDED FOR PROFESSIONAL USE ONLY AND MUST ONLY BE USED BY AUTHORISED STAFF IT IS DESIGNED TO WASH TABLEWARE GLASS CUPS BOWLS OVEN DISHES AND CUTLERY AND SIMILAR ITEMS IN THE RESTAURANT AND INSTITUTIONAL CATERING SECTOR AND COMPLIES WITH THE INTERNATIONAL STANDARDS ON ELECTRICAL AND MECHANICAL SAFETY CEI EN IEC 60335 2 58 61770 AND ELECTROMAGNETIC COMPATIBILITY CEI IEC EN 55014 1 2 61000 3 4 50366 THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY FAILURE TO COMPLY WITH THE INSTRUCTIONS IN THE MAN2. After a few seconds without the user pressing any buttons the display will return to the normal operating status and the modifications will be saved 15 gP smeg CEN 00 FT 0 See information on Smegtech 6 15 Starting the peristaltic pumps rapid filling of detergent and rinse aid delivery circuit Perform after the parameter modification procedure explained in the previous point Indicator lights showing O off S green orange Lt flashing With the glasswasher powered up access programming mode by pressing the on off Obutton for a few seconds at the beep release the button and press it again quickly QO Ln O within 0 5 seconds OO The peristaltic pumps continue to operate until the same button is pressed again The rinse aid and detergent symbol lights remain on as long as the pumps are on bear in mind that the rinse aid peristaltic pump fills the circuit in about 7 A minutes while for the detergent it only takes 2 minutes So VE draw only rinse aid from the jerry cans 1 for the rinse aid and the other for the detergent for the first 5 minutes and then also take in detergent for the last 2 7 MALFUNCTIONS SHOWN ON THE DISPLAY FOR THE TECHNICIAN The glasswasher is able to identify a number of malfunctions and show them on the display If the problem persists after the glasswasher has been switched off and back on proceed as described below The anti flooding system has Larg
3. WASHING PROGRAM THE APPLIANCE IS NOT SUITABLE FOR USE BY JUVENILES OR PERSONS WITH REDUCED PHYSICAL SENSORIAL OR MENTAL CAPACITIES OR THOSE WITHOUT THE NECESSARY KNOWLEDGE AND EXPERIENCE SUCH PERSONS MAY ONLY USE THE APPLIANCE UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY X DEPP 88 Smeg 2 TECHNICAL DATA Water intake pressure Water intake temperature Intake water hardness models with softener Rinse cycle water consumption Boiler capacity Tank capacity Standard cycle duration with intake water at 50 C Noise level Degree of protection Net weight Power supply cable type Fuse VOLTAGE 400V 50Hz 3 N PE 230V 50Hz 3 PE 230V 50Hz 1 N PE 2RR 230V 50Hz 1 N PE FUSE PROTECTION 13A 25A 25A 13A TANK HEATING 0 8kW 0 8kW 0 8kW 0 8kW SEE APPLIANCE LABEL MOTOR 0 7kW 0 7kW 0 7kW 0 7kW kPa bar f 5 IPX Kg HAR BOILER 1 5X3 5kW 5kW 3 3kW 1 7kW 100 600 1 6 15 C 60 C 15 f 60 f 3 2 6 11 90 150 240 50 4 5 CWG 60 63 CWH 84 87 HO7RN F 4 TOTAL CONNECTION 5 7kW 5 7kW 4 7KW 2 4kW Current 11A 16A 18A 11A CEN POWER CABLE 5X2 5 5X2 5 3X4 3X2 5 gP smeg CEN CAVITY DIMENSIONS FOR BUILT UNDER INSTALLATION APPLIANCE DIMENSIONS AND CONNECTION POSITIONS N B VALUE 1000 max 600 if siphon with valve is used N B VALUE max 60 heat ex
4. This value can be reset during pump maintenance see below 11 e88 Smeg Detergent pump total operating minutes display This value can be reset during pump maintenance see below Energy consumption kW display The Pc option indicates the total kW consumed since installation of the glasswasher or since the latest reset Display of the number of cycles performed When scrolling through the appliance parameters the tc 88888 item will also appear this is the count of the total cycles performed by the glasswasher since installation This parameter cannot be modified or reset unless the software is reprogrammed Customisation of duration of program P4 This submenu and the relative functions can only be accessed with the aid of a password available on SmegTech and only by technical staff 6 2 Quit SET UP menu D Dr 9 Cr Dr Wait more than 10 seconds without pressing any button and the appliance quits this menu automatically or press the on off button to exit Indicator lights showing O off S green orange xt flashing Caution the tank and boiler temperatures shown on the display may be differ from the actual temperatures by a few degrees especially in transient phases just after the FILL is completed just after the end of the cycle etc due to the inertia of the measurement probe 12 essesmeg CEN 6 3 Rinsing temperature s
5. turned off Connect the appliance to the user s earth system The Y terminal for the connection is in the bottom right hand corner of the appliance The earth wire PE is yellow green in colour the neutral wire N is blue and the live wires L1 L2 L3 are black grey and brown In the event of single phase connection 230V 1N the connection to the electrical mains must be made using a cable with plug compliant with the relevant regulations THE POWER SUPPLY CABLE AS PROVIDED MUST BE REPLACED BY THE N MANUFACTURER OR AN AUTHORIZED SERVICE CENTER IN COMPLIANCE WITH THE SPECIFICATIONS PROVIDED ON ELECTRICAL DIAGRAM SUPPLIED IN THE MACHINE IN ORDER TO PREVENT ALL RISKS essesmeg CEN 5 FIRST START UP First start up The electrical protection system must undergo a functional test before the appliance is put into operation The appliance must be installed and or inspected by qualified staff who will start it up for the first time and provide the relevant operating instructions Preparing for use important The rinse aid dispenser is fitted on all models the detergent dispenser only on some If both dispensers are present put the external detergent and rinse aid containers in place and insert the respective intake hoses on the rear of the appliance into them Red hose detergent blue hose rinse aid NOTE It takes about 10 15 wash cycles before they arrive in detergent and rinse tank and boiler Before inserting the hos
6. 4 INSTRUCTIONS FOR TECHNICAL STAFF 4 1 lumbing hookup Water supply and drain connection The water pipelines and electricity supply cable lead out of the bottom right hand corner of the appliance Connect the water intake hose to a connector with threaded fitting fitting the filter A provided in models with acquastop the filter and ring nut form a single unit The connection to the water mains must only be made with new hoses the use of old or worn hoses is not permitted FOR MODELS WITH A WATER SOFTENER AN APPROVED DOUBLE CHECK VALVE OR SOME OTHER NO LESS EFFECTIVE DEVICE PROVIDING BACKFLOW PREVENTION PROTECTION TO AT LEAST FLUID CATEGORY TWO SHALL BE FITTED AT THE POINT OF CONNECTION BETWEEN THE WATER SUPPLY AND THE FITTING OR APPLIANCE FOR MODELS WITHOUT A WATER SOFTENER AN APPROVED SINGLE CHECK VALVE OR SOME OTHER NO LESS EFFECTIVE DEVICE PROVIDING BACKFLOW PREVENTION PROTECTION TO AT LEAST FLUID CATEGORY TWO SHALL BE FITTED AT THE POINT OF CONNECTION BETWEEN THE WATER SUPPLY AND THE FITTING OR APPLIANCE The dynamic water supply pressure must be between 1 and 6 bar if it is higher a pressure reducer must be installed It is essential to fit a main stop tap on the water intake deliver pipeline the tap must be accessible after installation of the appliance so do not install it behind the warewasher The stated cycle duration applies to appliances supplied with hot water gt 50 C lt 60 C If the warewasher is supplied wit
7. P polypropylene straps PS expanded polystyrene corner guards top of packaging Wooden and cardboard components can be disposed of in accordance with the relevant regulations When the 6 gP smeg CEND product is decommissioned it must not be dumped in the environment it must be disposed of in accordance with the relevant regulations All metal parts are in stainless steel and can be removed The plastic parts are marked with the symbol identifying the material used and must be disposed of in accordance with the relevant regulations When the product is decommissioned it must not be dumped in the environment it must be disposed of in accordance with the relevant regulations All metal parts are in stainless steel and can be removed POSITIONING Caution the indoor system and premises in which equipment for institutions is installed N must comply with the relevant regulations The manufacturer declines all liability for direct or indirect injury or damage deriving from failure to comply with these regulations Before installation check that there are no objects or materials in the vicinity which may be damaged by steam or splashes of washing solution or that any such items are suitably protected Place the glasswasher in the chosen point and remove the protective film Level the glasswasher with the aid of a spirit level on its adjustable feet to ensure that it is stable all other mounting solutions must be approved by the manufacturer
8. UAL BY INCORRECT USE BY TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND BY THE USE OF NON ORIGINAL SPARE PARTS THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEE BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT WHEN DECOMMISSIONING THE APPLIANCE COMPLY WITH THE LOCAL WASTE DISPOSAL REGULATIONS FOR FURTHER INFORMATION ON THE TREATMENT RECOVERY AND RECYCLING OF THIS PRODUCT CONTACT THE COMPETENT LOCAL OFFICE THE DOMESTIC WASTE COLLECTION SERVICE OR THE SHOP WHERE THE PRODUCT WAS PURCHASED THE SYMBOL OF THE RUBBISH BIN WITH A BAR ACROSS IT ON THE PRODUCT OR IN THE TECHNICAL DOCUMENTATION INDICATES THAT THIS PRODUCT MUST NOT BE TREATED AS ORDINARY DOMESTIC WASTE BUT MUST BE CONSIGNED TO THE SPECIAL COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT NEVER PLACE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MIGHT CAUSE AN EXPLOSION INSIDE THE APPLIANCE NEVER LOAD DISHES DIRTY WITH ASH WAX OR PAINTS NEVER USE THE GLASSWASHER OR ANY PART OF IT AS A LADDER SUPPORT OR STAND FOR PEOPLE ANIMALS OR ANY OBJECT LEANING OR SITTING ON THE OPEN DOOR OF THE GLASSWASHER MIGHT CAUSE IT TO TIP OVER PUTTING PEOPLE IN DANGER NEVER LEAVE THE GLASSWASHER DOOR OPEN SINCE PEOPLE MIGHT TRIP OVER IT DO NOT DRINK ANY WATER LEFT IN THE DISHES OR GLASSWASHER AT THE END OF THE
9. above even when cleaning the floor underneath or in the vicinity of the glasswasher to ensure that fumes or drops cannot damage the steel surfaces IMPORTANT The glasswasher automatically performs program PO at the start of the day if water has been left in the tank and has dropped below the temperature of 40 C 11 2 Routine inspection of the spray arms Remove the washing and rinsing top and bottom spray arms by unscrewing the central screw remove the rinsing spray arms 3 and remove the screws 2 as shown Do not unscrew the nozzles Clean the holes and nozzles under a jet of clean running water do not use tools which might cause damage Reassemble the spray arms with care Clean the outside of the appliance with a damp cloth and neutral soap rinsing and drying thoroughly 11 3 Lengthy periods out of use If the glasswasher is to be out of use for a fairly long period of time the detergent and rinse aid dispenser devices must be emptied to prevent crystallisation and damage to the pumps Remove the intake hoses from the detergent and rinse aid containers and place them in a container of clean water then perform a few wash cycles followed by a complete pump out Finally turn off the master switch close the water intake valve and leave the door ajar until the interior is completely dry The detergent and rinse aid intake hoses must be put back into the containers when the glasswasher is returned to service taking care not to swap them o
10. ate in sequence If the door is opened CLOSE flashes and the program stops Close the door again and confirm the program start by pressing gt and holding it down for 1 second light L2 changes from green to orange 20 essesmeg CEN At the end of the program End flashes 9 F 0 Unload the dishes With the door closed to change to a fresh program instead of repeating the last one press the button The programs available are displayed If a program has already started oressl t and hold it down to interrupt it change the program by pressing P Confirm the program start by pressing and holding it down for 1 second light L2 changes back to orange N B During heating of the water in the boiler and tank with the cycle running the tank heating element V 7 and boiler heating element e symbols may appear on the display Filter presence sensor on some models only The filter is fitted with a sensor which checks that it is properly fitted if it is not in the correct position the word FiLter appears on the display 21 egge smeg CEND 9 CHOOSING THE PROGRAM PROGRAM TYPE OF DIRT DURATION P1 Glasses and cups Short about 1 30 1 with glassware function active TNT 2 with glassware function active 5 30 with sani function active OP Depending on the duration set As required from 3 to 10 The cycle duration stated above refers to t
11. before the total pump out at the end of the day the user will automatically be reminded to carry out the resin regeneration cycle required after a number of washes which depends on the hardness of the water about 30 for average setting HO3 In this case the sequence will be as follows JO Press the pump out button 2 rEgE and the duration rs i appear on the display JO Confirm by pressing D light L2 turns orange essesmeg CEN 9 OF re gt gt When pump out is complete the appliance switches to O OFF status Topping up with regenerating salt for models with water softener Salt must be added when the no salt light S appears on the display Top up with salt when there is no water in the tank to prevent washing water from getting into the water softener device Caution use only salt of the specific type do not use cooking salt The salt tank has a capacity of about 1 kg of coarse grained salt The salt tank is in the bottom of the appliance s tank After removing the basket undo the cap and pour the salt in using the funnel supplied Remove any salt residues around the opening before screwing the cap back on 11 MAINTENANCE AND CLEANING Although no particular scheduled maintenance is required users are advised to have the glasswasher checked by a specialist technician twice a year N B the manufacturer accepts no liability for wilful damage or damage deriving from carelessn
12. changer 1022 SCAMBIATORE 1000 MAX 840 MAX 320 RE REPERI 840 MAX 815 MIN rani gP smeg APPLIANCE DIMENSIONS AND CONNECTION POSITIONS N B VALUE 1400 WITH ASTERISK max 1000 if siphon with valve is used 1022 749 600 Ema pe 1 SE Sil AENEAN p 1 400 MAX MIN 860 MAX 920 MIN 140 MAX 200 MIN 1305 MAX 1365 e ceo x lt t e N 2 2 95 E Tom m u E KEY TO LETTERS USED IN DIAGRAM R LOWER BACK PANEL C FILLER HOSE Q Y EARTH TERMINAL E ELECTRICITY SUPPLY CABLE P PERISTALTIC HOSES S DRAIN HOSE T EXTERNAL DISPENSER POWER CABLE ENTRY POINT 3 INSTALLATION AND POSITIONING INSTALLATION and POSITIONING Bring the glasswasher to the installation site remove the packaging and check the appliance and components for damage any damage found must be reported to the transporter in writing The packaging components plastic bags expanded polystyrene nails etc must not be left within reach of children and pets since they are potentially dangerous All packaging materials used are environment friendly They can be kept without constituting any hazard or may be disposed of at a specialist waste disposal centre The plastic components suitable for recycling are marked as follows PE polyethylene external packaging film bag containing the instructions protective bags P
13. d or partially are unobstructed and the drain is not too obstructed high up see connection diagram WATER IN TANK AFTER PUMP OUT 28 egg smeg 13 MALFUNCTIONS SHOWN THE DISPLAY FOR THE USER The glasswasher is able to identify a number of malfunctions and show them on the display If the problem persists after the glasswasher has been switched off and back on proceed as described below TO ALLOW THE AFTER SALES SERVICE TO TAKE THE APPROPRIATE ACTION ALWAYS MAKE A NOTE OF THE ERROR INDICATED The anti flooding system has been ErrO1 activated for the relevant models Contact the After Sales Service only 4 Tank temperature probe malfunction Contact the After Sales Service Check that the water intake tap is on and the dynamic pressure in intake system inspect water intake filter and clean if necessary If the problem persists contact the After Sales Service 05 Tank water filling malfunction Inspect the filters for dirt and check that the drain hose is not blocked bent or crushed Check that the drain pump is not blocked by dirt proceed as described in point 10 2 Periodic checks If the problem persists contact the After Sales Service Contact the After Sales Service Boiler heating malfunction does not heat Err24 Boiler temperature probe malfunction Contact the After Sales Service Check that the water in
14. e instructions provided by the detergent producer on the pack Switch on the That there is That the filters are in Turn on the The level of master switch regenerating salt lace the spray arms mains water detergent and pel user the word pe in the relative rotate and there are B TM tap user rinse aid in the KG OFF appears on container if no foreign bodies in containers the display fitted the glasswasher 19 gP Smeg CEN 8 3 First use each day tank and boiler empty Indicator lights showing O off S green orange Lr flashing Display shows Actions and what happens With the door closed Press and hold it down with word FILL appears the glasswasher fills the tank after the water the boiler FILL 22 C has heated up light L2 shows orange and the boiler o amp heating element symbol amp appears on the display Wait for P1 to appear and LED L1 to change from red to green the tank heating element light comes on until the HE EI o the single phase connection Press the button quickly to display the tank left boiler right temperatures for a short time Load the dishes Select the program required by pressing Confirm the program start by pressing and holding it down for 1 second light L2 changes from green to orange Cycle in progress the progress of the cycle is displayed by vertical bars which illumin
15. e water leak check the origin of the problem 01 been activated for the relevant models only Tank temperature probe Tank temperature probe disconnected or not working malfunction aut The tank does not fill within the allowed time check water intake Tank water filling malfunction n tap dynamic pressure in intake system cleaning of water intake 16 essesmeg CEN filter possible damage to water intake hose or cleaning of rinsing nozzles If the problem persists during FILL tank pressure switch has failed continuous empty reading check whether tank safety pressure switch istripped leak from pipe connected to air trap If the problem occurs during work cycle filler hose bleeder valve fouled tank empties completely at end of a wash cycle due to siphon effect Inspect the filters for dirt and check that the drain hose is not blocked bent or crushed Check that the drain pump is not blocked by dirt by removing the insert on the sump from inside the tank If it persists check in this order with tank empty constant tank full signal tank pressure switch faulty or leak from connections of air trap connection pipe water entering pipe with tank full drain pump failure With tank full see above water pump out malfunction Too much water in tank With tank empty constant tank full signal safety pressure switch faulty or leak from connections of air trap connection pipe water enterin
16. egge Smeg PROFESSIONAL GLASSWASHER CEND TABLE OF CONTENTS 1 PRECAUTIONS FOR SAFETY AND USE innen trnev i EEERAN qv PERSE REY RUxn RYE VERE ER ien 3 2 TECAHNKALDATA 4 3 INSTALLATION AND POSITIONING eese nnne 6 4 INSTRUCTIONS FOR TECHNICAL nennen nennen nennen nnns 7 a1 ENN 7 A MEME 84 9 OM E E T 8 5 FT TTV 9 5 1 Using the water softener on models with this feature 9 6 SETUP cc 10 6 1 Glasswasher parameter modification 10 62 Qut SETUP EEE 12 6 3 RINSING temperature setup 13 64 VENN 13 65 AIC CISD OG IS SC EE A EEEE ETEA 13 6 6 Detergent dispensing setup 13 SEE AUOST TUCO o 14 6 8 Regeneration frequency setup models with 14 6 9 tStP minimum rinsing temperature 14 6 10 Rinse aid pump display and if required reset during maintenance 15 6 11 Detergent pump display and if required reset during maintenance 15 6 12 Energy consumption Display and reset if 15 6 13 Customisa
17. es into the containers fit the weights needed to ensure that they always draw in liquid from the bottoms of the containers and the filters onto their ends as shown f E 7 a If the detergent dispenser is factory fitted be retrofitted HE rar after ordering the relative kit As an alternative an external dispenser can be fitted making the electrical connection by means of an 5 RN F 2x0 5 mm electrical cable which can be laid along the route shown in the TECHNICAL DATA diagram and connected as shown in the wiring diagram supplied with the glasswasher The dispenser must operate on 230V 50 Hz with maximum power absorption of 15 W Connect to the detergent dispenser outside the glasswasher using the red hose mentioned above 5 1 Using the water softener on models with this feature only The quantity of lime in the water which indicates its hardness causes whitish marks on dry dishes and dishes also tend to lose their shine over time The glasswasher is equipped with an automatic water softener which removes the substances that cause hardness from the water with the aid of regenerating salt The first time the glasswasher is used a litre of water must be poured into the tank with the salt Whenever the tank is filled always take care to ensure that the cap is firmly closed The mixture of water and detergent must not get into the salt tank as this would impair o
18. ess neglect failure to comply with instructions regulations and standards or incorrect connections 11 1 Daily cleaning The glasswasher has IPX4 protection but the use of direct water jets for cleaning is forbidden Cleaning the filter during the day In case of particularly heavy duty working conditions the filter should be cleaned every 30 40 cycles keeping the machine in operating conditions to do this carry out the partial tank pump out routine program PO Press the 2 button and hold it down until PO and the duration of 1 appear on the display At the end of the pump out the word End flashes on the display The display returns to showing P1 Clean Confirm by pressing gt light L2 turns orange egg smeg EN the filter the glasswasher automatically fills the tank gt when the door is closed Remove the filters simply lift them out as shown here taking that no large residues fall into the sump underneath Clean them to remove residues and rinse with plenty of water then put them correctly back in place do not use sharp or pointed tools Clean away any limescale deposits to prevent excessive build ups If possible leave the door ajar when not in use Clean surfaces thoroughly and often with a damp cloth use neutral non abrasive detergents which do not use chlorine compounds which corrode and damage stainless steel Do not use the products mentioned
19. etup JO abo acl Modify the value of the parameter by pressingO Default value 71 o Min 71 max 85 6 4 Washing temperature setup Modify the value of the parameter by pressing Default value 62 C Min 52 C max 62 Indicator lights showing O off S green orange lt t flashing 6 5 Rinse aid dispensing setup RINSE AID Modify the value of the Delivery time Delivery parameter by pressing s quantity c c 0 0 6 0 7 12 1 3 18 2 0 default value factory preset 24 27 30 3 9 36 4 0 42 4 7 6 6 Detergent dispensing setup DETERGENT OG ae i Fe Mostly the value of the j parameter by pressing WIEC n s 33 default value factory preset 13 essesmeg CEN 6 7 Autostart function 00 I Modify the parameter ON OFF by pressing Set at on to start the cycle when the door is closed Set at off for cycle start after confirmation with the start button gt 6 8 Regeneration frequency setup models with softener e Default value modify the parameter to suit the mains water hardness e At first use the salt tank has to be filled It is subsequently sufficient simply to fill up with regenerating salt when necessary Hardness Hardness E dH German dF French e E gt Modify the degrees degrees o amp value of the Regeneration parameter by pressi
20. g pipe The problem might occur because water is continually entering the tank the causes are as for 5 see above If it persists check in this order damaged boiler heating element contactor failure boiler safety thermostat failure boiler temperature probe faulty or incorrectly positioned motherboard relay failure Important if the boiler heating element is damaged this might be due to operation with no water in the boiler the pressure switch is indicating full even with the boiler empty check and if necessary replace the boiler air trap and or the relative pressure switch the problem is generally preceded by boiler overheating E28 Boiler temperature probe boiler temperature probe disconnected or not working malfunction The boiler does not fill within the allowed time check water intake tap dynamic pressure in intake system cleaning of water intake Boiler water filling filter possible damage to water intake hose malfunction Or check in this order boiler pressure switch has failed continuous empty reading Boiler does not heat up as expected pipe leaking disconnected water entering pipe Err26 Boiler emptying malfunction check that rinsing spray arm nozzles are clean 17 boiler pressure switch has failed continuous full reading pipe leaking disconnected water entering pipe rinsing pump not working Err27 Boiler emptying malfunction Boiler pressure s
21. h cold water the cycle duration might increase depending on the intake water temperature The warewasher is fitted with a drain pump and can operate with drain connections on the floor or wall Refer to the connection diagram for the maximum permitted height of wall drains see TECHNICAL DATA gL smeg N Caution make sure that the intake and drain hoses are not bent constricted or crushed after installation When installing the drain hose to a siphon with valve the maximum height of the drain outlet is reduced to 600 mm 4 2 Electrical connection The glasswasher and any additional equipment must be connected to the electrical system by authorised skilled staff in accordance with the relevant regulations also comply with the technical instructions for the connection The total rated power is stated on the appliance s technical data plate The electrical protection devices fitted for the glasswasher must serve this appliance only Ail The user must have a master switch and a differential safety breaker with rating suitable for the appliance s characteristics installed on the electricity supply line in accordance with the relevant regulations These switches must be installed close to the glasswasher be easily accessible after installation and provide complete disconnection from the electrical mains in overvoltage class 111 conditions Warning The glasswasher is always powered up unless the master switch is
22. he glasswasher is connected to cold water this function will be less effective 10 3 Selecting the sanitisation function only available in P3 Increases the program s washing and rinsing temperatures and duration Press to select the sanitisation function then to JO confirm the program start N B the supplementary function remains selected until the program is changed or the glasswasher is switched off by pressing the button During execution of the selected program the display alternates between showing the supplementary function and the duration Glasses Load glasses upside down Cutlery Use the basket s provided Load cutlery loose preferably with the handle at the bottom taking care not to injure yourself with fork prongs or knife blades 23 gP smeg CEN TOTAL PUMP OUT AT THE END OF THE DAY The glasswasher is able to perform an automatic cleaning cycle at the end of the day gt 4 nen Press the pump out button 3 and the display shows ES UnLo and the duration Confirm by pressing 2 light L2 turns orange e pe vg is complete the appliance switches to o amp After a total pump out the filters should be cleaned as described above Never switch the glasswasher off with water in the tank always pump out first TOTAL PUMP OUT AT THE END OF THE DAY RESIN REGENERATION for models with water softener From time to time on models with water softener
23. hree phase appliances supplied with hot water at 50 C If the appliance is supplied with cold water the cycle duration might increase depending on the intake water temperature since the glasswasher is fitted with the HTR system which requires set temperature and pressure for rinsing 10 SUPPLEMENTARY FUNCTIONS Indicator lights showing O off green orange rt flashing To select a supplementary function when the program required is shown on the display P1 P2 P3 or P4 press the button Only one supplementary function can be selected for each program 10 1 Selecting the crys glassware function available in P1 P2 Reduces the program s rinsing temperature and duration After selecting the Crys function perform a cycle with the appliance empty to stabilise the boiler temperature OE P1 CRYS Press and hold it down to select the glassware function then press gt to confirm the program start 10 2 Selecting the erin extra rinse function available in P1 P2 P3 P4 Extends the duration of the rinse 22 gP smeg CEN FINN Press and hold it down to select the extra rinse function then press gt to confirm the program start During performance of cycles with Extra Rinse the cycle duration increases by about 30 because of the increased duration of the rinsing phase and the time consequently required to restore the level and temperature in the boiler If the Termostop is OFF and t
24. lease the amp 2 button and press it again to access the main PCB setup menu With the tank full during P1 P2 P4 1 Press the 6 button once The display will show UNLO 2 Press the button and hold it down for 5 7 seconds When the second beep is heard release the button and press it again to access the main PCB setup menu 20 9 D Rinsing temperature boiler temperature 10 gP Smeg CEN Washing temperature tank temperature eO 5 Quantity of rinse aid dispensed OPT only if installed the number indicates the number of seconds for which the peristaltic pump is operated go Quantity of detergent dispensed only if installed the number indicates the number of seconds for which the peristaltic pump is operated Start on start off i j rs 38830 Set at on to start the cycle when the door is closed Set at off for cycle start after confirmation with the start button gt Water hardness setting OPT on models with softener only Gr tStP on off on minimum rinsing temperature as set regardless of intake water temperature If the intake water is not hot the cycle duration might be a few seconds longer than the nominal timing off the minimum rinsing temperature might be a few degrees lower than the setting Rinse aid pump total operating minutes display
25. ng Setting Regeneration cycle duration 12 minutes With values over 60 dF an external water treatment device must be used and the regeneration frequency must be set on HOO 6 9 tStP minimum rinsing temperature function oet O Modify the parameter ON OFF by pressing 14 essesmeg CEN gt Set at on for minimum rinsing temperature as set set at off for rinsing regardless of boiler temperature If the parameter is set as off and hot intake water is not used the minimum rinsing temperature might be a few degrees lower than the setting A If the termostop device is set off the rinsing is no longer monitored and the user is responsible for ensuring that the minimum correct T are maintained for the tank and boiler It is particularly important to check the intake water temperature Also refer to the insufficient washing drying foam in tank point of the troubleshooting section restore T Stop ON and or connect the appliance to a hot water supply 6 10 Rinse aid pump display and if required reset during maintenance Pa l i To reset press for 3 seconds To reset press or 3 seconds 6 13 Customisation of duration of program P4 The duration of program P4 can be customised from 3 to 10 minutes Access the programming procedure and scroll through to mF using the 2 button then to 03 00 and press the button to set the time required from 3 to 10 minutes
26. peration of the regeneration system In this case warranty cover will be forfeited gg smeg A IMPORTANT A Whenever the type of detergent or rinse aid is changed it is ABSOLUTELY ESSENTIAL to flush out the peristaltic pumps by placing the external intake pipes in water for a few cycles Always use only products specifically recommended for use in a glasswasher Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance s water system The internal pipes of the detergent and rinse aid pumps should be replaced by the After Sales Service every 12 months or 15 000 wash cycles and operation of the diaphragm can be disposed of in accordance with the relevant regulations rinse aid pump should be checked 6 SET UP Set up i During first start up the functions parameters listed below must be set or adjusted 6 1 Glasswasher parameter modification procedure Only accessible after filling is complete or with the door open Indicator lights showing O off S green orange xt flashing Access programming mode With the tank empty during FILL 1 Switch on the appliance the display will show FILL 2 Open the door lift the hood depending on the model 3 Press the amp button once The display will show UNLO 4 Close the hood door depending on the model 5 Press the amp 2 button and hold it down for 5 7 seconds When the second beep is heard re
27. take tap is on and the dynamic pressure in intake system inspect water intake filter and clean if necessary If the problem persists contact the After Sales Service FUHR Check that the rinsing spray arm nozzles are not fouled If the PENE problem persists contact the After Sales Service Boiler emptying malfunction with Err27 Contact the After Sales Service Boiler heating malfunction Water pump out malfunction ENOG glasswasher is left full of water Err25 Boiler water filling malfunction m s N UJ Err28 overheating Contact the After Sales Service 29 egge smeg CEN INFORMATION AND AFTER SALES SERVICE FOR SMEG PRODUCTS COMMERCIAL GLASSWASHERS Our Sales Department staff will be able to provide you with information about prices and special offers Our After Sales Department will be able to provide you with guidance about keeping your appliance functioning correctly and put you in touch with your nearest authorised Service Centre Our whole product offering can be viewed at www smegfoodservice com International customers please contact your local SMEG distributor Smeg S p A Via Leonardo da Vinci 4 42016 Guastalla Reggio Emilia Tel 39 0522 8211 Fax 39 0522 821453 email foodservice smeg it 19 390 4918 04 26 05 2014 ManudEd Date 30
28. tion of duration of program 15 6 14 Service setting for After Sales Service 16 6 15 Starting the peristaltic pumps rapid filling of detergent and rinse aid delivery circuit 16 7 MALFUNCTIONS SHOWN ON THE DISPLAY FOR THE 16 o INSTRUCTIONS TON TRE USER vrede 18 ett smeg CEN COMOD IE Nc 18 82 Before NNN io ibus 19 8 3 First use each day tank and boiler empty 20 82 Cans the PONTA 21 9 CHOOSING THE PROGRAM Vvs 22 10 SUPPLEMENTARY FUNCTIONS ep DR bU ue Un sax et dae eo IN DU 22 10 1 Selecting the crys glassware function available in P1 P2 22 10 2 Selecting the erin extra rinse function available in P1 P2 P3 P4 22 10 3 Selecting the sanitisation function only available in P3 23 11 MAINTENANCE AND CLEANING cccccsscccceseccssssccceescecseeececeeesecseeeeetenseeseaesesees 25 PS S TT UE 25 11 2 Routine inspection of the spray arms esesseesee memes 26 113 Xensthyberiods out OT USO eee 26 17 TROUBLESHOOTING tiri tue Rat eee he ae OU ou EG HN on ERN dcn EV Ru ae e aite 27 13 MALFUNCTIONS SHOWN ON THE DISPLAY FOR THE
29. ver red hose detergent blue hose rinse aid 26 essesmeg CEN 12 TROUBLESHOOTING If the system fails to pump out because the drain pump is fouled as a result of incorrect filter positioning proceed as follows Bale out the glasswasher with a basin and disconnect it from the electrical mains Unscrew the screw A release the tang B and lift it Check that the impeller of the drain pump underneath the cover turns freely and is free from dirt limescale residues or pieces of glass Never use tools screwdrivers scissors etc PROBLEM POSSIBLE CAUSE POSSIBLE REMEDY LIGHT S1 DOES NOT COME ON Check electrical mains connection h Tue posset ee Wor Wait for the word FILL to go out WASHING PROGRAM DOES Yet finished filling NOT START The word CLOSE remains If the word CLOSE remains on the display even on the display with the door closed call the after sales service Spray arm washing holes blocked by dirt or limescale Filter fouled See Cleaning the filter during the day ee iS ME Check type and quantity of detergent detergent or rinse aid q y gent No enough detergent or rinse aid Pipe inside detergent and or rinse aid peristaltic being supplied detergent pump worn or broke have it replaced by the or rinse aid not being After Sales Service POOR WASHING RESULTS taken from the relative container glasses badly arranged Arrange glasses correctly LOW washing Check temperature sho
30. witch has failed continuous full reading with tank full First check boiler pressure switch has failed continuous full reading pipe leaking disconnected water entering pipe connected to air Boiler heating malfunction trap pressure switch continues to give full reading even with boiler overheating empty heating element operating dry Or circuit board relay failure or contactor failure 8 INSTRUCTIONS FOR THE USER 8 1 Control panel L 1 L2 Se bus D OG Additional function selection button L1 Mains power on light EN L2 Intake standby cycle in progress light red green 18 gP smeg CEN Oo L3 Pump out in progress light No rinse aid symbol if a system for monitoring outside the glasswasher is provided EN 7 Tank heating element on symbol No salt symbol if softener is fitted Boiler element on symbol No detergent symbol if a system for monitoring outside the glasswasher is provided 8 2 Before washing Use only detergents and rinse aids for industrial glasswashers Do not use detergents intended for hand washing We recommend the use of Smeg products specially developed for this glasswasher When topping up the tanks take care not to swap the products this might damage the glasswasher and cause malfunctions Do not mix different detergents this would damage the dispenser device Industrial glasswasher detergents may cause serious irritation Comply carefully with th
31. wn on the display call temperature the after sales service if less than 50 C Increase washing duration especially if dishes Inappropriate cycle set are very dirty or dirt has dried on Check that nozzles are clean and ensure that the softener is working properly if installed Check that the filter of the hose inserted in the rinse aid tank is not fouled Remove spray arms and clean them 10 2 Periodic checks Spray arm nozzles fouled Limescale in boiler Rinse aid unsuitable or Check container of rinse aid and whether it is INADEQUATE RINSING not being delivered suitable for the type of mains water correctly Check boiler temperature setting egge smeg CEN gt Rinsing temperature too If the problem persists contact the after sales low service Rinse aid unsuitable or Check container of rinse aid and whether it not being delivered is suitable for the type of mains water DISHES NOT PROPERLY correctly Restore T Stop ON and or connect the DRIED Water hardness above appliance to a hot water supply 12 dF or large amounts If the problem persists contact the after of dissolved salts sales service Drain hose incorrectly Check that the glasswasher drain hose and positioned or partially rain are unobstructed and the drain is not obstructed too high up see connection diagram STAINS ON GLASSES AND CUTLERY Drain hose incorrectly Check that the glasswasher hose and drain positione
Download Pdf Manuals
Related Search