Home

the manual

1. Diagram N 5 Diagram N 6 Diagram N 7 IMPORTANT The appliance s vent cap should be at least 24 in 61 cm from any outside adjacent or intersecting wall IMPORTANT The appliance s venting system should be inspected at least once a year and cleaned if necessary IMPORTANT THE VENT AIR INTAKE SYSTEM MUST BE PROPERLY INSTALLED TO IN SURE PROPER AND SAFE OPERATION SBI Stove Builder International Inc 6 VENTILATION INSTALLATION continued NJA Clearnace to unventilated soffit Clearance to outside corner Clearnace to inside corner INSIDE TO CORNER DETAIL v 4 A y EIAED dre B V a o V VENT TERMINAL 00 AIR SUPPLY INLET V AREA WHERE TERMINAL IS NOT PERMITTED Canadian Installation US Installation Clearance above grade veranda porch 12 inches 30 cm 12 inches 30 cm deck or balcony Clearnace to window or door that may be 6 inches 15 cm for appliance lt 10 000 BTU hr 6 inches 15 cm for appliance lt 10 000 BTU hr opened 3kW 12 inches 30 cm for appliance gt 10 000 3 kW 9 inches 23 cm for appliance gt 10 000 BTU hr 3 kW and lt 100 000 BTU hr 30 kW BTU hr 3 kW and lt 50 000 BTU hr 15 kW 12 36 inches 91 cm for appliances gt 100 000 BTU inches 30 cm for appliances gt 50 000 BTU hr hr 30 kW 15 kW
2. 1 and threaded mounting rod should be trimmed to comply to ee the dimensions shown in Diagram N 4 al a FLUSH WITH Final Assembly gt TO HEATER Remove the front cover of the heater by removing the control a knob and the two 2 screws on the top of the cover Slide the iji TOTAL LENGTH OF ROD front upwards WALL THICKNESS 5 127mm After tubes have been cut to length slide the tubes and the rod into position on the heater and adjust with the nut pro vided until you get a compact unit 1 12 7mm al Slide the heater and ventilation assembly through the hole TOTAL LENGTH OF INTERNAL TUBE until the heater reaches the wall For fhe model DV72 se WALL THICKNESS 2 1 2 64mm cure to the wall with the three 3 screws provided For the model DV 20 secure to the wall with the four 4 screws pro Diagram N 4 vided Check that hood protrudes the intended 4 1 4 10 8 cm from the exterior wall Seal any imperfections between wall and vent hood with putty making sure that nothing falls inside the hood See Diagram N 6 A protection plate resistant to high temperatures is available at extra cost for use with external combustible walls See Diagram N 7 SBI Stove Builder International Inc 5 VENTILATION INSTALLATION continued Minimum wall thickness 4 1 2 11 5cm Maximum wall thickness 13 1 2 35 cm
3. Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance Installation and repair should be done by a qualified service person The appliance should be inspected before use and at least annually by a qualified service person More frequent cleaning may be necessary due to excessive lint from carpeting bedding material etc It is imperative that control compartments burners and circulating air passageways of the appliance be kept clean WARNING Do not operate appliance with the panel removed cracked or broken Replacement of the panel should be done by a licensed or qualified service person Do not spray any aerosol near heater when functioning Do not store these elements near appliance Do not touch the grill to avoid burning yourself Do not touch the gases outlet cap while heater is in operation to avoid burning yourself Avoid blocking air inlet and hot air outlet Do nat spill water over the heater as it may cause corrosion Allow heater to thoroughly cool before servicing Input ratings are shown in BTU per hour and are for elevations up to 2 000 feet For elevations above 2 000 feet input ratings should be reduced 4 percent for each 1 000 feet above see level Refer to the National Fuel Gas Code The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1 2
4. Clearance to permanently closed window Vertical clearance to ventilated soffit lo cated above the terminal within a horizon tal distance of 2 feet 61 cm from the cen ter line of the terminal Clearnace to each side of center line ex 3 feet 91 cm within a hieght 15 feet 4 5 m i tended above meter regulator assembly above the meter regulator assembly Clearance to service regulator vent outlet 3 feet 91 cm i Clearance to nonmechanical air supply in 6 inches 15 cm for appliance lt 10 000 BTU hr 6 inches 15 cm for appliance lt 10 000 BTU hr let to building or the combustion air inlet to 3kW 12 inches 30 cm for appliance gt 10 000 3kW 9 inches 23 cm for appliance gt 10 000 any other appliance BTU hr 3kW and lt 100 000 BTU hr 30 kW BTU hr 3kW and lt 50 000 BTU hr 15 kW 12 36 inches 91 cm for appliance gt 100 000 BTU inches 30 cm for appliance gt 50 000 BTU hr hr 30 kW 15 kW Clearance to a mechanical air supply inlet 6 feet 1 83 m 3 feet 91 cm above if within 10 feet 3 m horizontally Clearnace above paved sidewalk or paved ij driveway located on publis property Clearance under veranda porch deck or balcony In accordance with the current CSA 8749 7 Natural Gas and Propane Installation Code In accordance with the current AWS 2223 NFPA 54 National Fuel Gas Code A vent shall not terminate directly above a paved sidewalk or paved driveway that
5. Take into consideration the area indicated for the gas con nection BS To HEATER The wall s thickness cannot be less than 4 1 2 11 5 cm nor ila 2E SOTA LENCO RODE can it exceed 13 1 2 35cm See Diagram N 5 Tube lengths WALL THICKNESS 5 127mm and threaded mounting rod should be trimmed to comply to the dimensions shown in Diagram N 3 1 25 4mm For Model DV20 Mark the four 4 5 16 8mm holes and drill Insert the four 4 plastic plugs provided in the previously drilled Diagram N 3 holes Mark the hole for the 6 1 4 16cm dia ventilation tube This must be rectilinear and with a slight fall towards the exterior of approx 2 degrees to avoid the entering of rain water I I I z TOTAL LENGTH OF EXTERNAL TUBE WITH HOOD rae into consideration the area indicated for the gas con E E a nection TOTAL LENGTH OF INTERNAL TUBE WALL THICKNESS 3 1 2 90mm tit The wall s thickness cannot be less than 4 1 2 11 5 cm nor can it exceed 13 1 2 35cm See Diagram N 5 Tube lengths
6. Shall your unit or a components be defective contact immediately your PSG dealer Prior to your call make sure you have the following information necessary to your warranty claim treatment e Your name address and telephone number e Serial number and model name as indicated on the e Bill of sale and dealer s name nameplate fixed to the back of your unit e Nature of the defect and any relevant information Before shipping your unit or defective component to our plant you must obtain from your PSG dealer an Authorization Number Any merchandise shipped to our plant without authorization will be refused automatically and returned to sender Gas Revision October 2009 D LONGVIE Eco Energy at the heart of your home Product imported from Argentina Importer SBI Stove Builder International inc 250 De Copenhague St Augustin de Desmaures Quebec Canada GIN 4R9 Tel 418 878 3040 Fax 418 878 3001 Web site www psg distribution com Online warranty registration We encourage you to register your warranty online at the following website address www psg distribution com 2
7. BurnerAssemblyGasket_______________________ 1 112 16360 Gas Intake Fitting 1 122 15756 GaslntakelockFiting O 2 132 2462 Gas Fitting Support SSS O 1 14 2 2465 Control Insulation O 1 15 2 PiezolgnitorNlt Od0 1 16 2 2463 Control Bracket 1 172 2464 Piezo Ignitor Bracket 1 18 2 12455 Piezolgntr 1 19 2 11699 Piezo Ignitor Button O 1 20 2 11698 Knob rame 1 21 2 16365 ControlRod SS 1 22 2 11626 ControlKnob 1 23 2 2461 Cabinet Bak 1 24 2 2419 Top Deflector 1 25 2 2421 Left Side Deflector 1 262 2420 Right Side Deflector 1 272 342 CA Air Chamber S gt poi 28 2 2411 Cabinet Front 1 292 243 CabinetGlassSuppot 4 30 2 17767 Cabinet Glass 1 312 383 Grill Cast Aluminum 1 32 2 17912 LONGVIELogo 1 33 2 11634 Cabinet Slide 2 MEE BL NI 5 5 5 A gt 5 S 5 gt e IS IS S IS IS e SID IE e A INC m Note Please contact your PSG dealer in order to obtain the genuine part number you are looking for If you experience any difficulty in obtaining a particular part number please do not hesitate to contact the importer listed on the last page of this owner s manual SBI Stove Builder International Inc 16 BURNER ASSEMBLY REPAIR PARTS SBI Stove Builder International Inc 17 BURNER ASSEMBLY RE
8. LOINC VE VENTED WALL FURNACE Owner s Manual DV20 and DV12 models F DG05480 DGO5481 DGO5482 DG05483 ESO MODEL DV20 MODEL DV12 MAY BE INSTALLED IN A MANUFACTURED HOME MOBILE HOME This Appliance may be installed in an aftermar ket permanently located manufactured home USA only or mobile home where not prohib ited by local codes This appliance is only for use with the type of gas indicated on the rating plate This appli ance is not convertible for use with other gases unless a certified kit is used This appliance is only for use with the type of gas indicated on the rating plate This appliance is not convertible for use with other Save this manual for future reference SBI Stove Builder International Inc WARNING If the information in these instructions are not followed exactly a fire or explosion may result causing property damage personal injury or loss of life Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance Do not touch any electrical switch do not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supp
9. of the unit We suggest that before every heating season or at least once a year conduct the following minimum service functions STEP 1 The gas supply should be turned OFF at the shutoff valve in the supply line leading to the appliance or at the gas source The gas to the unit should then be disconnected so the unit can be removed from the wall STEP 2 Remove the front cover by removing the control knob and the two 2 screws on the top of the front Then slide the front upwards STEP 3 Carefully examine the interior of the vent pipe If you notice any blockages or obstruction that was not part of the unit when it was installed Clean the pipes and prepare them for reattachment to the unit The vent system should be inspected periodically or at least once a year and cleaned if necessary If removal of the venting is required follow the instructions in the Ventilation Installation section of this manual for reassembly STEP 4 Look inside the openings of the rear of the unit and check for foreign materials Remove any objects which may block or obstruct the free flow of combustion and ventilation air STEP 5 Visually check the pilot and the main burner for signs of excessive dirt or debris through the heat exchanger front glass If you find any of these follow the directions below to reach the components to clean otherwise continue to the next step To Remove Pilot Find the pilot Loosen the head of thermocouple disconnect the pilot g
10. PAIR PARTS LIST PART 14399 10381 16353 16354 16355 14397 14398 16362 15707 16322 2466 16322 14400 12456 2468 15707 16322 2467 16364 15707 16367 16368 Burner Orifice DV12 Liquid Propane 16370 Burner Orifice DV20 Natural 16369 Burner Orifice DV20 Liquid Propane 16357 16356 14396 14395 16358 12457 14394 16359 Pilot Thermocouple Fitting 8199 345 za Note Please contact your PSG dealer in order to obtain the genuine part number you are looking for If you experience any difficulty in obtaining a particular part number please do not hesitate to contact the importer listed on the last page of this owner s manual SBI Stove Builder International Inc 18 VENTING REPAIR PARTS LIST QTY 74 2474 Air Incoming Tube DVi2 terma fr s4 344 Enameled Vent Cap DVi2 r m Note Please contact your PSG dealer in order to obtain the genuine part number you are looking for If you experience any difficulty in obtaining a particular part number please do not hesitate to contact the importer listed on the last page of this owner s manual SBI Stove Builder International Inc 19 PSG WALL MOUNTED GAS HEATERS LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable This warranty covers brand new products only which have not been altered modified nor repaired since shipment from factory Proof of pur
11. as supply line only on the side of the pilot not on the valve side Remove the two 2 M4 screws that hold the pilot in place Clean with a vacuum cleaner or use a can of compressed air To Remove Burner Loosen the gas line from the burner on the right side of the unit On the left side of the unit unscrew the nut that holds the burner in place Then remove the burner Clean with a vacuum cleaner or use a can of compressed air Note You can remove the main burner pilot assembly if you don t unscrew the M4 screws that hold the pilot to the burner Before reinstalling the assembly check the ceramic fiber sealing gasket If it is damaged or worn replace with new gasket available from your dealer STEP 6 Reassembly the unit back to its original state and mount the unit to the wall Properly reassemble and reseal the vent air intake system STEP 7 Reconnect the gas supply and check for leaks using a soapy water solution Bubbles on any of the joints indicate a leak is present and must be repaired urn of the gas when making such repairs Check to make sure that the piezo ignitor still lights the pilot STEP 8 While the main burner is ON Check the flames to verify that they are burning a clean blue color See Diagrams 10 12 Note After maintenance the first few minutes of the heater operation will probably have some yellowish flying traces in the flame due to the burning of particles left behind during the cleaning operation Liquid P
12. chase dated bill of sale model name and serial number must be supplied when making any warranty claim to your PSG dealer This warranty applies to normal residential use only Damages caused by misuse abuse improper installation lack of maintenance over firing negligence accident during transportation power failures downdrafts or venting problems are not covered by this warranty This warranty does not cover any scratch corrosion warping or discoloration caused by over firing abrasives or chemical cleaners Any defect or damage caused by the use of unauthorized parts or others than original parts void this warranty An authorized qualified technician must perform the installation in accordance with the instructions supplied with this product and all local and national building codes Any service call related to an improper installation is not covered by this warranty The manufacturer may require that defective products be returned or that digital pictures be provided to support the claim Returned products are to be shipped prepaid to the manufacturer for investigation If a product is found to be defective the manufacturer will repair or replace such defect Transportation fees to ship the product back to the purchaser will be paid by the manufacturer Repair work covered by the warranty executed at the purchaser s domicile by an authorized qualified technician requires the prior approval of the manufacturer Labour cost and repair work
13. conform with the Manu ac tured Home Construction and Safety Standard Title 24 CFR Part 3280 or when such a standard is not applicable the Standard for Manufactured Home Installation ANSI 2225 7 or Standard for Gas Equipped recreational Vehicles and Mobile Housing CSA 2240 4 Available from American National Standards Institute Inc National Fire Protection Association Inc 1430 Broadway Batterymarch Park New York NY 10018 Quincy MA 02269 GAS SPECIFICATIONS Natural 10 000 BTU hr Liquid Propane 10 000 BTU hr Natural 18 000 BTU hr Liquid Propane 18 000 BTU hr MANIFOLD PRESSURE Natural Gas DV12 5 8 w c DV20 5 2 w c Propane LP Gas DV12 10 8 w c DV20 10 6 w c GAS INLET 3 8 NPT SUPPLY MIN PRESSURE MAX PRESSURE Natural 7 W C P 10 5 W C P Propane LP 11 0 W C P 13 0 W C P USE ONLY THE TYPE GAS SPECIFIED ON THE RATING PLATE SBI Stove Builder International Inc 2 SAFETY RULES 10 11 12 13 14 15 16 17 18 19 20 21 22 Due to high temperatures the appliance should located out of traffic and away from furniture and draperies Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition Young children should be carefully supervised when they are in the same room as the appliance Clothing or other flammable material should not be placed on or near the appliance
14. is located between two single family dwellings and serve both dwellings Permitted only if verdana porch deck or balcony is fully open on a minimum of two sides beneath the floor For clearnaces not specified in AWS 2223 NFPA 54 or CSA 8749 7 one of the following shall be indicated a Aminimum clearances valve determined by testing in accordance with section 2 19 6 or b A reference to the following footnote Clearance in accordance with local installation codes and the requirements of the gas supplier SBI Stove Builder International Inc 7 VENTILATION INSTALLATION continued A DV 20 26 66 cm 8 1 4 21 cm A B DV 12 15 38 cm 4 5 16 11cm 4 1 8 10 5cm 22 5 8 57 5 cm Gas Valve 15 3 4 40 cm See Mounting Detail Drywall Anchor SBI Stove Builder International Inc GAS CONNECTION A qualified gas appliance installer must connect the heater to the gas supply Consult all local codes Use new black iron or steel pipe only Internally tinned copper tubing can be used in some areas when permitted by local codes Only use pipe of 1 2 or greater diameter to allow full gas volume to heater Excessive pressure loss will occur if the pipe is too small A manual shutoff valve union and plugged 1 8 NPT pressure tapping point must be installed upstream of the heater FIGURE 6 CAUTION A sediment trap must be installed upstream of the heater to prevent moisture and contami
15. lier INTRODUCTION Your LONGVIE heater is especially designed to provide maximum comfort to you and your home lts large solid injected aluminum front grill assures the optimum use of the generated heat in the ambient maintains normal temperatures behind the heater to avoid sticking of particles which would soil the wall You can feel safe with absolute security guaranteed by e Its thermocouple security valve which cuts the supply of gas in the event of the heater extinguishing due to strong air currents momentary interruption of the supply of gas e lis gas pressure regulator assures an optimum operational function avoiding peak pressures in the gas supply affecting normal combustion e Its gas tight combustion chamber totally enameled avoids gases which are caused by combustion to contaminate the air and ensures a useful long lasting working life Long lasting working life Guaranteed by the quality of its components and high technology applied in the process of fabrication and especially by the traditional vocation of LONGVIE to produce durable products for your maximum comfort and satisfaction LOCAL CODES Install and use the heater with care The installation must conform with local codes or in the absence of local codes use the latest edition of The National Fuel Gas Code ANSI Z223 1 NFPA 54 Natural Gas and Propane Installation Code CSA B149 1 A manufactured home USA only or mobile home OEM installation must
16. nants from passing through the pipe to the heater controls and burners Failure to do so could prevent the heater from operating reliably FIGURE 8 IMPORTANT Loosen the pipe adapter on the flex tube before installing to the Manual Shutoff ey eter DIDI Valve Flexible Gas Hose If allowed by local codes From External Regulator na Tee Joint Sediment Pipe Trap a Cap Diagram N 9 Gas Connection 3 Minumum CHECK GAS TYPE The gas supply must be the same as stated on heater s rating plate If the gas supply is different DO NOT INSTALL the heater Contact your dealer for the correct model Connecting directly to an unregulated propane LPG tank can cause an explosion Reattach the front to the unit Use the same screws removed in the instructions on page 5 Reinstall the control knob SBI Stove Builder International Inc 9 OPERATING INSTRUCTIONS MON FOR YOUR SAFETY READ BEFORE LIGHTING SE WARNING If you do not follow these instructions exactly a fire or explosion may result causing property damage personal injury or loss of life A This appliance has a pilot which can be light with the equipped piezo ignitor When lighting the pilot follow these instructions exactly B BEFORE LIGHTING smell all around the appliance area for gas Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor WHAT TO DO IF YOU SMELL GAS e Do not a
17. oking through the viewing window on the front of the unit 5 Press the knob down lightly and turn counterclockwise KD to the Pilot Press again downwards LO Position the process 1 through 6 Piezo M If the knob does not pop up when released stop and immediately call your ser za N vice technician or gas supplier M Ifthe pilot will not stay lit after several tries turn the gas control knob to OFF and AT call your service technician or gas supplier Pilot HH 7 Press down and turning the control knob counterclockwise KOM to the Hood desired temperature The temperature can be regulated between HI and LO capacity according to the indicated scale marked on the knob When the heater is first started after installation or if the heater has not been used for a long period of time there is a normal delay of gas from the gas supply through the gas control on the heater In this case maintain pressure on the knob at the Pilot position for 30 40 seconds and then try the piezo lighter AA TURN OFF GAS TO APPLIANCE IE When the heater is not to be in use for a long period of time or for servicing turn the control knob clockwise VO to the OFF position and close the main gas supply valve SBI Stove Builder International Inc 10 MAINTENANCE INSTRUCTIONS As with all fuel burning appliances it is important to conduct periodic maintenance functions that will allow for contin ued safe efficient operation
18. psig 3 5 kPa The appliance must be isolated from the gas supply piping system be closing its equipment shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 5 kPa This gas appliance must not be connected to a chimney flue serving a separate solid fuel burning appliance The installation make provisions for adequate combustion and ventilation air The installation must provide adequate accessibility clearances for servicing The efficiency rating of this appliance is a product thermal efficiency rating determined under continuous operating conditions and was determined independently of any installed system The minimum inlet gas supply for the purpose of input adjustment Do not use this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been under water SBI Stove Builder International Inc 3 MINIMUM CLEARANCES TO COMBUSTIBLES EPA Rear 0 Inches Omm to bracket 6 15cm Sides 6 Inches 15cm Top 24 Inches 61cm Floor 7 Inches 18cm to top of carpeting tile etc 24 61cm 7 18cm Diagram N 1 INSTALLATION INSTRUCTIONS The following Diagram Diagram N 2 serves as a reference for the installation of your heater with the ventilation provided with the unit The template that is provided with the heate
19. r Motor 8 Housing Green Ground Female Terminal White Female Terminal Supply Cord i White ae Black from power supply JO coins Blower Motor White from power supply Ground Green Wiring Schematic DV20 DG05480 1 SPARE PARTS SBI Stove Builder International Inc 13 REPAIR PARTS LIST DV20 DG05480 1 E Qry A lt pret Co e e e e e e me e es E N a a m 181 Piezo Ignitor Nut S O TIN 11315 Loop 2466 Gas Fitting Support Note Please contact your PSG dealer in order to obtain the genuine part number you are looking for If you experience any difficulty in obtaining a particular part number please do not hesitate to contact the importer listed on the last page of this owner s manual SBI Stove Builder International Inc 14 v ke 14 lt O LL aa lt O YN g N 00 LO O N m gt O 15 SBI Stove Builder International Inc REPAIR PARTS LIST DV12 DG05482 3 72 16374 Air Intake Tube 3 8 2 15951 Spacing Bo 2 92 2471 Ceramic Fibre Washer D71 D57 4 102 2473
20. r can also be used In this case fold it at the dotted line 7 below the heater which indicates the floor level and make it coinciding with the floor level as a minimum fix it to the wall with adhesive tape Also take into consideration the other minimum distances shown on Diagram N 1 Diagram N 2 Model DV12 Model DV20 15 in 38 cm 26 in 66 cm _ 8 1 2 21 5 cm _ 4 76 si 4 76 _ V pi 11 2 cm 112cm 741 46 L 19 5 cm GAS INLET 3 8 NPT GAS INLET 3 8 NPT MINIMUM DISTANCE FROM FLOOR MINIMUM DISTANCE FROM FLOOR SBI Stove Builder International Inc VENTILATION INSTALLATION The ventilation system consist of 1 External Tube Air incoming tube with enamel hood riveted in place 1 Threaded Mounting Rod 1 Internal Tube Outgoing flue gases 1 Adjusting Nut For Model DV12 TOTAL LENGTH OF EXTERNAL TUBE WITH HOOD Mark the three 5 16 8mm holes and drill WALL THICKNESS 4 3 4 120mm Insert the three plastic plugs provided in the previously drilled m holes 1 12 7mm Mark the hole for the 4 1 2 11 5cm dia ventilation tube 4 This must be rectilinear and with a slight fall towards the ex Se terior of approx 2 degrees to avoid the entering of rain water
21. ropane will have some evidence of yellow tips on the flame Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance Before completing your periodic maintenance check ensure the heater area is kept clean and free from combustible materials gasoline and other flammable vapors and liquids Also check to see that the flow of combustion and ventilation air around the vent cap on the outside of the structure is not obstructed SBI Stove Builder International Inc 11 Diagram N 10 Correct Flame Pattern Optional Blower AC02008 DV20 model only CAUTION Label all wires prior to disconnection when servicing controls Wiring errors can cause improper and dangerous operation Verify proper operation after servicing Permanently lubricated bearing system WARNING ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong re ceptacle Do not cut or remove the grounding prong from this plug SBI Stove Builder International Inc If any of the original wire as supplied with the appliance must be replaced it must be replaced with 600 volt 150 degree C wire or its equivalent Wiring Diagram Rocker Switch Female Terminal u Female Terminal Blowe
22. to the account of the manufacturer are based on predetermined rate schedule and must not exceed the wholesale price of the replacement part All parts and labour costs covered by this warranty are limited according to the table below The manufacturer at its discretion may decide to repair or replace any part or unit after inspection and investigation of the defect The manufacturer may at its discretion fully discharge all obligations with respect to this warranty by refunding the wholesale price of any warranted but defective parts The manufacturer shall in no event be responsible for any special indirect consequential damages of any nature which are in excess of the original purchase price of the product A one time replacement limit applies to all parts benefiting from a lifetime coverage This warranty applies to products purchased after March 1 2009 _ WARRANTY APPLICATION _ DESCRIPTION PARTS LABOUR Combustion chamber welds only and castings E Lifetime 3 years Stainless steel firebox components surrounds and heat shields and plating defective manufacture PE PR A Carbon steel firebox components burner and glass retainers 3 years o lyear o Gas valve pilot assembly amp related parts heat sensors switches rheostat f e 2 years l year wiring and other controls AA AA Optional blowers ceramic glass thermal breakage only paint peeling year n a and gaskets Pictures required
23. ttempt to light any appliance e Do not touch any electric switch do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department C Use only your hand to push in or turn the gas control knob Never use tools If the knob will not push in or turn by hand don t try to repair it call a qualified service technician Force or attempted repair may result in a fire or explosion D Donotusethis appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water A LIGHTING INSTRUCTIONS STOP Read the safety information above on this page Piezo Ignition Press the knob lightly and turn clockwise PT O to the OFF position EP OFF Position HI Position 3 Wait five 5 minutes to clear out any gas If you then smell gas STOP Follow LE B in the safety information above on this page lf you don t smell gas go to the next step 6 Press the Piezo Ignition button to light the pilot Repeat this operation with the knob pressed down until the pilot has lit When the pilot lights continue holding Thermocouple pressure for another 10 seconds Release the knob If the pilot goes out repeat Pilot Position 4 Find the pilot by lo

the manual

Contents

Download Pdf Manuals

Related Search

Related Contents