Home

X07 MIDI Foot Controller Users Manual

1. 2 1 MIDI MIDI is Voodoo This is wrong Although MIDI can do much more what you need as a guitarist is very simple This is how MIDI works A device such as a foot controller sends a command to another device e g a looper switcher using a MIDI cable The transmitting device e g the toot controller notifies the recipient e g the looper switcher what it should do That s all You can connect your Prostage devices and use the basic functions directly without having to deal with MIDI If you want to use the advanced functionality of the system you can find more detailed information on MIDI in the users manual of the System Manager software 2 2 StageWire StageWire is a further develooment of MIDI The technology has been developed by Prostage specifically for the use on stage StageWire is a connection where multiple devices communicate with each other bidirectional via a Standard microphone cable Using StageWire you can interconnect up to 14 Prostage foot controllers to control the XDS XLS XTMpro The foot controllers are joined together in a chain This means you simply run a microphone cable from the first foot controller to the second another cable from the second to the third foot controller and so on The foot controller s are supplied with power by the XDS XLS XTMpro 2 3 Instant Access Stompbox Mode On Off Switches Instant Access are direct access switches These on off switches
2. 127 Otherwise your chosen center position will be ignored and the expression pedal is calibrated linear You can easily check if the expression pedal is calibrated correctly Move the pedal while watching the red LED on the XDS XLS XTMpro which flickers when the expression pedal is sending MIDI commands If the LED flickers throughout the complete motion from top to bottom the pedal is calibrated correctly Calibration of Expression Pedal No 2 connected to Ring Basically this works like the calibration of pedal No 1 But you have to press the buttons 4 and 6 for approx three seconds to enter the calibration mode Page 6 4 Operating Modes amp Operation There are basically two different types of commands the foot controller can send e Program Change gt program changes or program numbers respectively are used to recall presets of multi effect devices or of a MIDI capable guitar amp e Instant Access gt Switches which directly turn on and off a function on the receiver unit e g the loops of the XDS XLS or the switching outputs of the XTMpro This is also called Stompbox Mode Which commands are sent depends on the operating mode Ex works the X07 sends 7 different program numbers e g to recall presets of multi effect devices or of a MIDI capable guitar amp Other operating modes Instant Access switches and additional features such as tap can be set with the System Manager software The tap function offe
3. adjusted in an effects device Page 4 3 Controls and Connectors 3 1 The Front Panel PROSTAGE foot controller X07 Buttons Buttons which are defined as Instant Access switch on and off a function of the receiver directly e g a loop of the XDS Buttons that are used for Program Change send the corresponding preset number LED The LED shows either the switching state Instant Access Stompbox Mode or the active preset depending on its assigned function 3 2 The Rear Panel PROSTAGE professional foot controller amp Gyn29730 RE CE a ee StageWire Main Connect the StageWire Main socket via a standard microphone cable with the StageWire socket from the XDS XLS XTMpro The foot controller is powered via the StageWire connection It does not need a separate power Supply StageWire Link If you work with multiple foot controllers connect the StageWire Link socket to the StageWire Main socket of the next foot controller Like this you can interconnect up to 14 Prostage foot controllers in a row daisy chain Expression Pedal You can connect a standard expression pedal to the expression pedal socket Using a so called Y cable you can also connect two expression pedals You will find all the information about this on the next page Page 5 3 3 Connecting an Expression Pedal to the Foot Controller You can connect a standard expression pedal to the jack
4. stands for professional live equipment The X07 is plug and play This means that you can plug it in and use It without having to configure anything The X07 foot controller is connected to the Prostage XDS XLS XTMpro via one standard microphone cable The StageWire technology developed by Prostage thereby achieves a secure connection between the foot controller and the looper switcher Prostage s philosophy is control without limits We want you to be able to setup your system exactly as you want it to work while keeping it as simple to use as possible Therefore there are lots of things inside the system you can configure yourself To set up the additional features of the X07 you will need the System Manager software This is available on our website free for download Mac amp PC If you have any questions or if something does not work as you expect please do not hesitate to contact us info prostage eu Your questions will also help us to improve this users manual We are also looking forward to your suggestions concerning new features We are working to improve the functionality of the system You can easily upgrade the software of the X07 yourself You can find more information about this topic in the users manual for the Prostage System Manager software The Prostage team wish you lots of fun with the new X07 and big success in your musical career Lukas Truninger Founder amp Developer Page 3 2 Terminology
5. work like an analog pedal switch which is connected directly to the amplifier for example to switch between the channels So at the foot controller you can define a switch which is e g firmly assigned to a loop of the XDS XLS XTMpro This switch then simply turns on and off the loop at the looper switcher 2 4 Preset Program Change Presets are saved settings that can be recalled with a switch on the foot controller Program Change A preset contains all settings of the amplifier and effects belonging to a sound e g Clean You create for example the following presets e Preset 1 Clean gt Channel 1 from the amplifier amp chorus switched on e Preset 2 Lead gt Channel 2 of the amplifier amp delay and booster activated If you now press button 1 on the foot controller the amplifier switches to channel 1 and the chorus is turned on If you press button 2 the amplifier switches to channel 2 The delay and the booster are turned on The chorus is turned off simultaneously So you can switch your complete guitar rig with a single button You no longer need to perform a tap dance on different switches to adjust your sound 2 5 Expression Pedal An expression pedal is a kind of volume pedal that is connected to the MIDI foot controller However the expression pedal does not control a guitar signal but generates MIDI Continuous Controller with which for example the volume the effects mix or the delay time can be
6. PROSTAGE control without limits X07 MIDI Foot Controller Users Manual Firmware Version 1 30 As at 22th February 2014 Prostage S L Apdo 57 ES 07560 Cala Millor info prostage eu www prostage eu Table of Contents 1 Introduction 1 1 X07 Features 3 t2 The Prostage System 3 2 Terminology 4 2 1 MIDI 4 2 2 StageWire 4 2 3 Instant Access Stompbox Mode On Off Switches 4 2 4 Preset Program Change 4 2 5 Expression Pedal 4 3 Controls and Connectors 5 3 1 The Front Panel 5 32 The Rear Panel 5 3 3 Connecting an Expression Pedal to the Foot Controller 6 3 4 Calibration of the Expression Pedal 6 4 Operating Modes amp Operation 7 4 1 7 Program Changes 7 4 2 7 Instant Access 7 4 3 Programs Instant Access 7 4 4 Instant Access Programs 7 5 Firmware Upgrade 8 6 MIDI Implementation Chart 8 7 Warning Instructions and Warranty 9 7 1 Warnings and Safety Instructions 9 TZ Warranty Support 9 7 3 Disposal of Old Devices 9 8 Declaration of Conformity 10 NOTE gt This manual uses digital bookmarks You can show them by clicking on the flag icon in the top left of Acrobat Reader A click on a topic flips directly to that chapter Page 2 1 Introduction Dear Customer Thank you for purchasing the Prostage X07 MIDI foot controller The X07 is a compact foot controller designed specifically for guitarists who just need a few sounds presets or who like to switch on and off certain functions of th
7. RTANT gt In order to use the expression pedal s you have to calibrate them first You have to repeat the following process each time you connect a different expression pedal Even switches must be calibrated 3 4 Calibration of the Expression Pedal Calibration of Expression Pedal No 1 connected to Tip e On the foot controller simultaneously press the buttons 4 and 7 for approx three seconds until the three lower LEDs light up You are now in calibration mode e Move the expression pedal to the position dead stop where you like to have the MIDI value O low e Press the 1 button Pressing any other switch will abort the calibration process e Now the four upper LEDs light up e Move the expression pedal to the other dead stop which is the position where you like to have the MIDI value 127 loud e Press the 1 button again e LED 2 5 6 lights up e Move the expression pedal to the center position e Press the 1 button again The calibration is now complete gt f you don t want to calibrate a middle position or if you calibrate a switch you can cancel the center position calibration last two steps by pressing any other button than the 1 button Then the expression pedal is calibrated linear You can also calibrate a logarithmic motion curve if you position the pedal a little bit away from the middle when calibrating the center position However the middle position must differ at least 10 from 0 and 10 from
8. but vice versa The first switches are used to send on off commands The remaining switches send program changes Page 7 5 Firmware Upgrade The firmware is the operating system the software within the X07 New firmware adds more functionality to the foot controller You can upgrade the firmware to the latest version yourself All information about this can be found in the manual of the System Manager software 6 MIDI Implementation Chart The X07 foot controller is part of the coherent Prostage system The X07 handles all MIDI data as they are configured by the System Manager software Therefore you will find the MIDI Implementation Chart in the manual of the System Manager software Page 8 7 Warning Instructions and Warranty 7 1 Warnings and Safety Instructions For reasons of the product liability we are obligated to make clear certain safety aspects which must not be ignored under any circumstances The devices must not be stored or operated in damp or wet environment The device serves for controlling MIDI equipment and amplifiers and may be used for this purpose exclusively This foot controller uses the Prostage StageWire technology It may only be connected to a Prostage receiver device XDS XLS or XTMpro or to the link connector of another Prostage foot controller using the StageWire technology The foot controller is supplied with electricity by the receiver device ohantom powered The equipment may be opened by qualifi
9. e receiver directly Stompbox Mode To operate the X07 a Prostage XDS XLS or XTMpro is required With the X07 foot controller you can directly switch on and off the loops amp switching outputs of the Prostage looper switcher as well as functions of modern guitar amplifiers and other MIDI devices Stompbox Mode Instant Access But you can also recall different presets stored settings configurations Or you can use a combination of the Stompbox Mode and presets The Prostage foot controllers further come with a connection for two expression pedals and the opportunity to connect multiple foot controllers in a chain 1 1 X07 Features e Connects to the Prostage XDS XLS XTMpro via StageWire microphone cable e Phantom powered the X07 is powered by the XDS XLS XTMpro e Link Connector several foot controllers can be interconnected directly daisy chain e Connector for two expression pedals e The connectors are positioned in a way that prevents the plugs from damage by treading e Sends Program Change 1 7 e Direct switching functions Instant Access Control Change e Four different operating modes e Seven high quality buttons with noticeable click e LED for each switch e Programming via System Manager software e Up to eight different MIDI messages per preset Program Change or Control Change via the MIDI mapping of the XDS XLS XTMpro e Delay tap function 1 2 The Prostage System Prostage
10. ed technical personnel only There are no user serviceable parts inside the devices In order to avoid damages you should be careful when transporting and setting up the devices Please avoid strong variations in temperature Particularly the change from the cold transport vehicle to the usually warm Stage can cause condensing humidity which can cause leaks and thus can evoke defects Usually 60 minutes are sufficient to equalize the temperature For transportation always carry the devices in a robust packing or rack especially if you change your place of work frequently No containers filled with liquid may be placed on the equipment 7 2 Warranty Support All Prostage PurpleLine units are covered by a 2 year warranty Prostage shall not be liable if the damage was caused by inappropriate use or if the units are not connected as described in this users manual There are no user serviceable parts inside the unit The detailed terms of the warranty can be downloaded on the Prostage website If you need technical support please contact your local dealer or email into prostage eu 7 3 Disposal of Old Devices The PurpleLine products are subject to the European guideline 2002 96 EC All old electric and electronic devices must be disposed separately from the domestic waste using the collection points provided by the government The devices must not be disposed with domestic or skip refuse Information about collecting points or collection dat
11. es can be asked from the local administration or the local waste management company Please also carry the packing to an environmentally fair disposal Cardboard boxes can be transferred with wastepaper collections or to the public collecting stations for recycling Foils of the shipment are collected by the local waste management company and are forwarded to environmentally fair disposal Page 9 8 Declaration of Conformit Company Prostage SL Apdo 57 ES 07560 Cala Millor Type of equipment PurpleLine System Trademarks Prostage StageWire Models XDS XLS XTMpro X10 X07 X05 X01 XB1 The products meet the requirements of the following standards EMC EN 55103 2 EN 55103 1 2009 EN 55103 2 2009 EN 61000 3 2 EN 61000 4 2 EN 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 3 EN 61000 4 11 Safety IEC 60065 2001 EN 60065 2002 A1 2006 Cor 2007 A11 2008 Year 2011 Cala Millor 14 Dezember 2011 Lukas Truninger CEO Information to the user Class B Statement C This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Howe
12. rs you the opportunity to adjust e g the delay time of an effect by rhythmically tapping on a switch of the foot controller Therefore you must tap the beat on the button at least twice The receiver unit can thus recognize the song tempo You will find further information about the special features of the Prostage foot controllers in the users manual of the System Manager software gt The operating modes and features listed below are set using the System Manager software Changes must always be confirmed in the System Manager with Update Foot Controller so that the foot controller adopts the new settings More information about this can be found in the manual of the System Manager software 4 1 7 Program Changes In this operation mode the foot controller sends MIDI Program Change commands 0 6 or 1 7 respectively 4 2 7 Instant Access This is the Stompbox Mode In this operating mode the foot controller sends on off commands This means it switches the relays of the XDS XLS XTMpro directly and sends the Control Change commands assigned in the MIDI Switches tab 4 3 Programs Instant Access This is a hybrid of the two first operating modes The first switches send Porogram change commands The remaining switches send on off commands The number of switches which will send program changes is defined by the Number of Programs setting 4 4 Instant Access Programs This is similar to the Programs Instant Access
13. socket of the foot controller Simply connect your expression pedal to the foot controller by a short mono jack cable If you like to use two expression pedals you will need a Y cable also called insert cable An insert cable has two mono plugs on one end Plug one into each expression pedal The other end of the cable has a stereo jack Plug this into the expression pedal connector of the X07 For the technology enthusiasts among you the potentiometer of expression pedal 1 is located between tip and shield The potentiometer of expression pedal 2 Is between ring and shield The top of a stereo jack cable is called tip the center ring is called ring Custom cables are available from Prostage You can also use a volume pedal as an expression pedal In this case you have to connect the output of the volume pedal to the foot controller You will get the best resolution if you use a pedal made for keyboards with a 10k ohm or a 20k ohm potentiometer One expression pedal Two expression pedals Y Cable Lk dleo Pedil COC A Pedal 2 Exp Pedal 1 Expression pedal with switch e g to control the Remote WahWah gt The switch is connected as expression pedal 2 Switch Exp Pedal Hence the Control Change assignment for the switch is set under CC No Exp Pedal 2 Instead of an expression pedal you can also connect a switch to use it as Tap for example IMPO
14. ver there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 2014 Prostage SL Page 10

X07 MIDI Foot Controller Users Manual

Contents

Download Pdf Manuals

Related Search

Related Contents