Pro-Ject Speed Box MK II
Contents
1. AUDIOw SYSTEMS INSTRUCTIONS FOR USE Pro Ject Speed Box MK II Dear music lover thank you for purchasing a PRO JECT AUDIO Speed Box MK Il The unit permits electronic speed change of your Pro Ject record player between 33 and 45 r p m and also permits the replay of shellac records by allowing 78 r p m with an appropriate pulley and cartridge Only models with mains socket power supply 16V 190mA AC max nes The Pro Ject Debut III Phono SB Pro Ject 1 2 Comfort and Pro Ject RPM 6 1 SB may not be used with the Speed Box These models are equipped with an electronic speed change as a standard In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse ES Important notice Connecting the record player Connect the low voltage plug Output 16V from the Speed Box to the socket in the record players motor V Make all connections whilst the Speed Box is disconnected from the power supply Mains power connection The Speed Box is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your house Connect the low voltage plug from the power supply to the socket Power 16V before connecting the power supply to the mains Speed selection 33 45 r p m Speed Box MKII 33 45 Speed The belt must be on the s2. he product by unauthorized persons release the manufacturer from any liability over and above the lawtul rights of the customer PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to This guide was produced by ATR Audio Trade GmbH press The manufacturer reserves the right to make Copyright 2005 changes to the technical specification without prior Audio Tuning GmbH All rights reserved notice as deemed necessary to uphold the ongoing process of technical development Pro Ject Audio Pro Ject Speed Box MK II Revision 10 10 05 1 12 05 3
3. maller 50Hz models larger 60Hz models diameter part of the motor pulley Press the speed change button to switch between 33 and 45 r p m The selected speed is shown respectively by the lit LED To play at 45 or 78 r p m please always start the turntable at 33 r p m and then switch to the higher speed when it has attained full speed Replay at 78 r p m In order to replay shellac records at 78 r p m your turntable must be equipped with the 78 r p m pulley which is available as an optional accessory for most models After fitting the 78 r p m pulley please proceed as follows Remove the platter and using the tool from the accessory kit fit the belt around the larger diameter step of the pulley Replace the Platter start the turntable at 33 r p m and switch the speed to 45 r p m the platter will then revolve at 78 r p m Fitting the 78 r p m pulley Before beginning work fit the cartridge s needle protection cover Remove the platter and drive belt Please remember that sweat or sticky fingers will impair the function of the belt Use a piece of kitchen paper or a cloth to remove the belt Measure the height of the pulley above the plinth in order to ease correct refitting Using a small screwdriver loosen the grub screw in the neck of the pulley just enough to remove the pulley vertically without using force Refit the pulley in the opposite order Tighten the grub screw carefully making sure you do not overtighten it Fit
4. the drive belt around the subplatter and the pulley Again use a piece of paper or cloth to avoid soiling the belt Replace the platter 78 r p m is not available with the models 1 2 Comfort Xperience Xperience SuperPack RPM 9 1 and RPM 9 1X ES The models Debut Ill Phono SB RPM 5 RPM 5 SuperPack and RPM 6 1 SB are equipped with an mechanic speed change for 78 r p m Switching to 78 r p m with the Perspective is done by exchanging the motor and belt 2 Pro Ject Audio Pro Ject Speed Box MK II Revision 10 10 05 1 12 05 Switching on and off Pressing the power switch of Your Pro Ject Turntable alternately starts or stops the motor Technical specifications PRO JECT SPEED BOX MK II Speed change 33 33 45 11 r p m or 78 r p m with optional 78 r p m pulley only Power output 16V 190mA AC max power consumption 3W max Outboard power supply 16V 500mA AC suitable for your country s mains supply Dimensions H x W x D 38 x 105 x 120mm Weight without power supply 540g Service Should you encounter a problem which you are not able to alleviate or identify despite the above information please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions nes for use Modification or change to any part of t
Download Pdf Manuals
Related Search