14000 Series Satellite Transmitter Install & User
Contents
1. 6 1 82m cord Operating Range 32 122 F 0 50 C non condensing environment Canadian Notice The manufacturer rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output signal is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device Transmitter Display Specifications The transmitter has a lighted front display that shows important information Figure 1 14000 Series Transmitter Display Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 3 Display Specifications Table 2 14000 Transmitter Display Specifications Component Description Time Displays the precise time received from the GPS Receiver If AM or PM is on the display then the 12 hour option is selected If neither AM nor PM is on the display then the 24 hour option is selected Daylight Saving Time The letters DT Daylight Saving Time or ST Standard Time will be displayed when adjustment for Daylight Saving Time is active If neither DT nor ST is displayed then switch 3 is in the down position and the transmitter will not adjust for Daylight Saving Time GPS Communication The GPS Communication indicator appears when the transmitte2. 1 This device may not cause harmful interference 2 This device must accept any interference including interference that may cause undesired operation Changes or modifications to any part of the Primex Wireless System components not expressly approved by Primex Wireless could void the user s FCC IC authority to operate the equipment Radio Frequency RF Exposure To comply with FCC IC RF exposure requirements for mobile transmitting devices the transmitter is only to be used or installed in locations where there are at least 20cm approximately eight inches separation distance between the antenna of the transmitter and all persons Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 1 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION OPERATION OR MAINTENANCE OF PRODUCT Some of the following information may not apply to your particular product model however as with any electronic product precautions should be observed during installation operation and maintenance l Never operate the transmitter without the antenna being properly connected to the transmitter Operating the transmitter without an antenna can lead to permanent damage of the transmitter and poses a safety risk l Do not touch any of the antennas while broadcasting l Standard acceptance procedures must be followed prior to operating this equipment in the proximity of life support systems l
3. Do not operate the transmitter outdoors in wet areas were there is standing water or in areas where there is condensation or the risk of condensation Use in any of these environments will damage the transmitter and void the warranty l Do not open the transmitter to alter the internal elements in any way This will void the warranty and could lead to unsafe conditions malfunction and violations of FCC IC regulations Primex Wireless disclaims any liability or responsibility for the results of improper or unsafe installation practices Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 2 SYSTEM SPECIFICATIONS This section provides the specifications of the XR Time Synchronization system components 1 Watt Transmitter Specifications Table 1 1 Watt Transmitter Specifications Parameter Specification Operating Frequency Range 72MHz Channels 49 channels available pre programmed prior to shipping Channel 1 through 16 72 10 72 40 MHz Channel 51 through 74 72 42 72 98 MHz Dimensions 17 0 L x 12 W x 1 7 D 43 2cm x 30 5cm c 4 32cm Maximum Transmission 1 Watt at transmitter Radio Technology Narrowband FM Weight 9lbs Settings Time Zone factory preset LAN Local 30 min offset serial USB Ethernet connectivity Daylight Saving Time Bypass switch Display Liquid Crystal Display LCD Power Supply Input 120 VAC 50 60 Hz 0 6 Amp Output 9 VDC 2 78 Amp
4. Channel The Channel Number menu allows the user to change the channel by using the up or down button The channel number must be set to the same channel number as the Primary Transmitter tESt Test The Test menu allows the user to hear audible beeps with a valid time date reception This will occur 5 seconds after the test menu is selected It will continue to be in this mode until the menu button is pressed again leav ing the menu mode and returning to normal mode LtU Last Time Update The Last Time Update menu allows the user to see the last time update time and date cycles every second This will occur 5 seconds after last time update menu is selected The unit will remain in this mode for a minute wherein it will time out and return to the menu mode Soft Software Revision The Software Revision menu allows the user to see the software revision on the unit This will occur 5 seconds after last time update menu is selected The unit will remain in this mode for a minute wherein it will time out and return to the menu mode dst Daylight Sav ing Time Calendar The Daylight Saving Time Calendar menu allows the user to see the current Daylight Saving Time calender in use This will occur 5 seconds after last time update menu is selected The unit will remain in this mode for a minute wherein it will time out and return to the menu mode donE Done The Done menu allows the user to exit the menu mode This will occur 5 seconds
5. XR TIME SYNCHORNIZATION 14000 SERIES SATELLITE TRANSMITTER INSTALLATION amp USER GUIDE Doc Part No 14000M 082713 Legal Notice Copyright 2013 Primex Wireless Inc All rights reserved U S Patents 6 873 573 7 352 657 Other Patents Pending Printed in the USA Information in this document is subject to change without notice No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical or otherwise for any purpose without the prior written permission of Primex Wireless Contact Primex Wireless United States Canada United Kingdom Address 965 Wells Street Lake Geneva WI 53147 1310 Kerrisdale Blvd Unit 4 Newmarket ON L3Y 8V6 Unit G420 Dean Clough Halifax West Yorkshire HX3 5AX Email info primexinc com info primexwireless ca info primexwireless co uk Web www primexwireless com www primexwireless ca primexwireless co uk Telephone 800 537 0464 800 330 1459 0800 3896996 Fax 262 248 0061 905 952 0134 01422 349462 Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide I CONTENTS Regulatory Compliance 1 Important Safety Instructions 2 System Specifications 3 1 Watt Transmitter Specifications 3 Transmitter Display Specifications 3 Installation and Configuration 5 Verify Setup Primary Transmitter with GPS Receiver 5 Satellite Transmitter Location G
6. after the done menu is selected returning to the normal mode saving all settings Internal Dip Switch Configuration The Receiver Switch has an internal dip switch panel that sets the configuration for the time date display automatic Daylight Saving Time and automatic channel scanning To access the dip switch panel remove the unit s large cover Remove the switch cover by removing the 2 Phillip head screws located in the upper right and lower right of the unit The dip switch panel is located on the top of the unit identified by the blue eight 8 switch panel CAUTION Except when setting the Dip Switch Options the unit cover should remain closed and secure at all times Table 6 Dip Switch Option Specifications Switch Sets ON Position OFF Position 2 Time Date displays only the time displays current time for 8 seconds and the date for 2 seconds 3 12 24 Hour displays the time in 24 hour format displays the time in 12 hour format 4 RF Channel Scan enable the scan and look for a suitable channel disable the scan and only look on the selected channel for time d ate event info 5 Daylight Saving Time DST DST is disabled DST is enabled 6 7 8 do not apply to the use of this unit Signal Indicator The LED signal indicator RX is located on the front right side of the Receiver Switch unit below the antenna l Green LED will flash each time a transmitted signal is received by the Receiver Swit
7. all be your sole exclusive remedy for any breach of warranty Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 15
8. ch from the transmitter at its update time Green LED will flash for 60 minutes when it has received a valid time update or Green LED will remain solid for 60 minutes if it has NOT received a valid time update l Yellow LED will continue to flash if the unit goes 48 hours without receiving a time update Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 9 Installation and Configuration Internal Dip Switch Configuration Install Receiver Switch 1 Attach the rubber antenna to the Receiver Switch as shown Figure 7 Figure 7 Receiver Switch 2 Power down the Satellite Transmitter 3 Connect the serial cable of the Receiver Switch into the GPS IN Socket on the back of the Satellite Transmitter Figure 8 Satellite Transmitter Back View 4 Power up the Satellite Transmitter 5 Press the Menu middle button on the front of the unit to scroll through the Menu options to the Channel Mode Ch displayed 6 Press the up or down button to set the channel number to match the primary transmitter s transmit channel 7 Scroll through the menu to the donE mode After 5 seconds the Receiver Switch will time out and return to the Day Date mode saving the channel selection 8 Determine the best mounting location for the Receiver Switch a Locate the room area the transmitter is to be installed in Close all doors and windows before testing b DO NOT hold the rubber antenna during testi
9. ed herein are exclusive and in lieu of all other warranties express or implied or statutory including any liability arising under any warranty or merchantability or fitness for a particular purpose implied statutory or otherwise In no event shall Primex be liable for any incidental special indirect or consequential damages whether resulting from the use misuse or inability to use this product or from defects in the product Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitations or exclusion may not apply to you To obtain warranty service If after following the instructions in the product guide you are certain the product is defective please contact Primex Wireless Technical Support to assist with troubleshooting the issue If the issue cannot successfully be resolved and the product is under warranty an RMA Return Material Authorization will be generated The RMA form will be provided via email with detailed instructions for the return All merchandise returned must be shipped to Primex Wireless Attn Returns Dept N3211 County Road H Lake Geneva WI 53147 Primex Wireless retains the exclusive right to repair or replace the unit at its sole discretion All merchandise returned must be shipped to Primex Wireless Attn Returns Dept N3211 County Road H Lake Geneva WI 53147 Primex Wireless retains the exclusive right to repair or replace the unit at its sole discretion Such sh
10. guration Setup the Transmitter Table 4 14000 Series Transmitter Switch Component Specifications Switch Component Description Rotary Switch A channel selection Warning Do Not adjust this switch It is only to be set to the frequency specified on the FCC IC application Factory preset to the FM frequency on which the transmitter will broadcast There are 16 available channels The chart below explains which switch positions correspond to which channel numbers Switch No Channel No Switch No Channel No 0 16 8 8 1 1 9 9 2 2 A 10 3 3 B 11 4 4 C 12 5 5 D 13 6 6 E 14 7 7 F 15 Rotary Switch B Sets the time zone Use a small slotted screwdriver to adjust the rotary switch 4 for Atlantic Time Zone 5 for Eastern Time Zone 6 for Central Time Zone 7 for Mountain Time Zone 8 for Pacific Time Zone 9 for Alaska Time Zone A for Hawaii Time Zone Switch 1 Sets the Daylight Saving Time Calendar Up to automatically change to the new Daylight Saving Time calendar in 2007 Down to abide by the old schedule in 2007 Switch 2 Sets the direction of UTC offset Up for U S and Canada Down for Europe Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 7 Installation and Configuration Setup the Transmitter Switch Component Description Switch 3 Sets the automatic Daylight Saving Ti
11. me adjustment Up for automatic Daylight Saving Time changes Down to bypass Daylight Saving Time adjustments Switch 4 Sets the clock display on the transmitter Up for 12 hour display Down for 24 hour display 2 Plug the supplied 9 Volt 2 0 Amp DC power supply transformer into the transmitter 3 Plug the power supply transformer into a 120 VAC outlet Setup Receiver Switch To access the Receiver Switch menu preferences press the Menu button located on the front of the unit By pressing and holding the Menu button the Receiver Switch will cycle through the menu options Figure 6 Receiver Switch l While in the Channel menu option if there are no changes made in a minute of entering a menu section it will time out and save the displayed value exiting the menu mode l If a value is changed while cycling through the menu it will be saved and continue to cycle l While in test mode it will remain in the selected mode until the menu button is pressed again to exit After entering changes it is recommended to step through the menu options until the option donE is displayed to exit the menu mode the menu will display donE NOTE Changes made in the Menu will be saved when the menu is exited Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 8 Installation and Configuration Setup Receiver Switch Table 5 Menu Mode Options Specifications Display Menu Description Ch
12. mitter In areas that do not observe DST this feature must be disabled on the circuit board of the switch 1 Disconnect the receiver switch from the Satellitle Transmitter 2 On the Receiver Switch remove the access cover and change dip switch 5 to the ON position as shown in Figure 9 Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 11 Confirm Reception Figure 9 Receiver Switch with Cover Removed Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 12 Special Circumstances SETUP MULTIPLE TRANSMITTERS WITHIN THE SAME FACILITY 1 Setup each Satellite Transmitter and Receiver Switch as per the steps in this guide 2 The channel number of the Satellite Transmitter is preset to the channel number specified on the red label located on the top of the box the transmitter was packaged in Contact Primex Wireless Technical Support if you require assistance 3 Use the buttons on the Receiver Switch to toggle through to LED menu and set the channel number to match the XR system channel with the strongest available signal This signal may be from either the Primary Transmitter or the nearest Satellite Transmitter 4 Cycle power on the Receiver Switch after changing the channel Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 13 SUPPORT Technical Support Prime Wireless Technical Support responds to specific questi
13. ng as this can affect the sensitivity of the receiver Instead hold the switch by the sides of the housing while locating the best mounting position Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 10 c Place the Receiver Switch in the EXACT location where it will be mounted This is crucial as closeness to walls can degrade receiver sensitivity i If the exact location is not known be sure to test the Receiver Switch in several locations If any locations tested are unsuccessful note this for future reference 9 Power Cycle the Receiver Switch power at least 1 2 times after installation is complete and verify the green LED begins to flash Doing this will ensure a solid signal is being received l To cycle power the Receiver Switch remove the switch cover by removing the 2 Phillip head screws located in the upper right and lower right of the unit Use caution when removing the cover to avoid causing the up or down menu buttons to fall off the circuit board l Press and release the Reset button located in the upper right corner to the left of the antenna mounting 1 to 2 times and verify the green LED begins to flash The flashing of the green LED indicates a solid signal is being received 10 Mount the Receiver Switch in its final location and verify the switch settings For additional information see Setup Receiver Switch located on page 8 NOTE When the Receiver Swi
14. ons about product features system configuration and troubleshooting All support services will be delivered in accordance with your organization s support agreement and warranties Contact Technical Support Before contacting Primex Wireless Technical Support make sure you have satisfied the system requirements that are listed in your product documentation When you contact Technical Support please have the following information available l Customer ID l Problem description l Device hardware information l Error messages l Troubleshooting performed before contacting Primex Wireless Technical Support Telephone 800 404 8112 Email techsupport primexinc com Fax 262 248 0061 Hours 7 00 am to 7 00 pm CST Monday through Friday Web www primexwireless com Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 14 WARRANTY One Year Limited Warranty Primex Corporation warrants this product to be free from defects in materials and workmanship for a standard of one year from the date of purchase Primex will at its sole option repair or replace any components that fail in normal use Such repairs or replacements will be made at no charge to the customer for replacement parts The customer will be responsible for any transportation costs This warranty does not cover failures due to misuse abuse accidental or unauthorized alterations or repairs The warranties and remedies contain
15. r is communicating with the GPS Receiver The parentheses indicate the time signal is being received Day Date Displays the day and date received from the GPS satellite Channel Number Displays the channel number 1 16 the transmitter is set to Red LED The red LED Light Emitting Diode is located on the right side of the front panel of the transmitter The LED flashes on initial setup until a GPS time signal is received or when a severe GPS Receiver signal problem has occurred and no time data has been received from the GPS Receiver in 48 hours See the Troubleshooting section of this guide for additional information Receiver Switch Specifications Included with Satellite Transmitter Table 3 Receiver Switch Specifications Component Description Cable 5 1 52m RS232 cable connects Receiver Switch to the Satellite Transmitter Dimensions 5 75 14 6cm L x 4 25 10 8cm H x 1 25 3 16cm D Antenna 12 5 31 75cm L Weight 0 75 lb 34kg Power Supply Input 120 VAC 50 60 Hz 0 4 Amp Output 9 VDC 0 25 Amp 6 1 83m cord Operating Range 32 158 F 36 70 C Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 4 System Specifications Transmitter Display Specifications INSTALLATION AND CONFIGURATION This section provides the procedures required to install and configure your 14000 Series Satellite Transmitter system and components Verify Setup P
16. rimary Transmitter with GPS Receiver Installation of the Satellite Transmitter begins with setup of the primary transmitter with GPS receiver l The Primary Transmitter must be setup and working prior to installation of the Satellite Transmitter l The Primary Transmitter transmits the signal to the Satellite Transmitter via the Receiver Switch NOTE For the setup and installation of the primary transmitter refer to the installation guide of the primary transmitter model Figure 2 Primary Transmitter Setup Illustration Satellite Transmitter Location Guidelines The Satellite Transmitter must be in a location where it can receive a signal from the Primary Transmitter Typical Application Drawings Do not adjust the channel numbers on your transmitter This figure is an example designed to demon strate how a repeater switch chain works Figure 3 Example of Horizontal Installation Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 5 Figure 4 Example of Vertical Installation Setup the Transmitter 1 Set the switch preferences located on the back of the transmitter The transmitter continually checks the position of the switches The switches select time zone channel number 12 or 24 hour display and the observance of Daylight Saving Time Figure 5 14000 Transmitter Back View Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide 6 Installation and Confi
17. tch is mounted its antenna must be vertical Do not use an analog clock to determine if a mounting location will be adequate for signal reception The receiver in a clock is more sensitive than the Receiver Switch and therefore the switch may not work in areas where a clock works Confirm Reception When the Receiver Switch is connected to the powered Satellite Transmitter an R will appear in the upper right corner of the transmitter display window This may take up to a minute The green RX LED on the Wireless Receiver Switch will flash when a valid signal is initially received This LED will then flash once per second signifying a successful time update If the green LED is solid the Receiver Switch missed the last update Time updates occur once per hour NOTE If the Satellite Transmitter does not receive a time update from the Receiver Switch after 48 hours its yellow Caution LED will begin flashing and an error will be logged Last Time Update To verify the last time the Receiver Switch received and applied a valid time date update toggle through the Menu to the Last Time Update LTU section Special Circumstances For areas that do not observe Daylight Savings Time DST set the transmitter s Daylight Saving Bypass reciver switch bypass step below NOTE In the event the receiver switch does not receive a transmitter signal when the DST change is scheduled to occur the switch will automatically adjust the time on the trans
18. uidelines 5 Typical Application Drawings 5 Setup the Transmitter 6 Setup Receiver Switch 8 Internal Dip Switch Configuration 9 Signal Indicator 9 Install Receiver Switch 10 Confirm Reception 11 Last Time Update 11 Special Circumstances 11 Setup Multiple Transmitters Within the Same Facility 13 Support 14 Warranty 15 Primex Wireless 14000 Series Satellite Transmitter Installation amp User Guide II REGULATORY COMPLIANCE Federal Communications Commission FCC Industry Canada IC License Requirements l Operation of the Transmitter requires a FCC IC operating license which must be obtained prior to operation l FCC licenses must be renewed every 10 years and the IC licenses must be renewed annually l As a service Primex Wireless will file the license application if the end user desires it An end user that does not want Primex Wireless to file for the original site license will be required to complete a waiver form file the required application and receive a valid license from the FCC IC prior to use If you have any questions or need any assistance please contact Primex Wireless at 1 800 537 0464 l Primex Wireless requires a copy of the licenses in order to complete the factory presets Product Compliance l This device complies with Part 90 and Part 15 of the FCC rules and RSS 210 of Industry Canada l Operation of this device is subject to the following two conditions
Download Pdf Manuals
Related Search