PVS15DT Personal Viewing System and CNTE7
Contents
1. Custom Feature Default Automatic Power On Off Disabled Home Button Analog channel 4 Inactivity Timer Disabled Closed Caption On Off Disabled Promotional Information Content Disabled PIC PVS Screen Programming Analog PVS screen with software version 1 1 or higher Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 19 Quick Reference to Custom Features Once you are familiar with setting up the customized Cardio Theater features you may find the following table useful as a quick reference These features can only be set up using the standalone controller Table 1 Quick reference to customized features You may find it useful to make a photocopy of this page which you can easily carry with you as you program the controllers Be sure to plug in headphones and change the channel to an analog channel before doing any of these steps appears Automatic Power On Off Home Button Inactivity Timer Closed Caption Promotional Information Master Reset Action Feature Feature Feature On Off Feature Content PIC Feature Programming for PVS Screen Feature Access Press both Press both Press both Power Press both Press both Power Press both Volume A and Power Press both feature Volume A and Volume A and and Home Volume A and and Home Volume A and Channel amp Channel A Channel A Channel A Enable Press 1 Press Source as With 152. PVS15DT Personal Viewing System and CNTE7 Standalone Controller Operation and Maintenance Guide E v CARDIO sage THEATER Important Safety Instructions Always follow basic safety precautions when using this equipment to reduce the chance of personal injury or property damage e Read all instructions before installing and using the equipment Follow any labels on the equipment e Use the power adapter provided with the equipment Plug the power adapter into an appropriate grounded power outlet as marked on the equipment Do not use accessory attachments that are not recommended by the manufacturer as such attachments may cause injuries e Position power cables so that they are not walked on or pinched by items placed upon or against them e Make sure that the equipment has adequate ventilation Do not place anything on top of or over the equipment Do not use on a cushioned surface that could block the ventilation openings e Keep the equipment away from water and moisture e Locate the equipment away from sources of heat such as radiators heat registers and stoves Avoid temperature extremes e Avoid dropping anything on or spilling anything inside the equipment because doing so can damage the electronics e Do not attempt to service the unit yourself except to follow the maintenance instructions found in this manual Operation and Maintenance Guide Important Safety Instructions
3. A or D This section explains the analog and digital menus You can display a menu using the standalone controller or remote control Access to these menus and their features should be limited to the installing technician and select facility personnel While you are in a menu if you do not press a button for a short period of time the menu disappears and the PVS screen returns to normal viewing mode Table 2 gives an overview of how to use both menus Tables 3 through 6 show the menus for analog and digital channels Operation and Maintenance Guide Using the Menus Table 2 How to use the menus Action Remote Control Standalone Controller Press both Volume V and Channel W buttons for 3 seconds Access Main Menu Press Menu button Use Channel CH and buttons Use Channel A and V buttons Move up and down through the menu Select an item Press SEL button Press Power button Use Volume A and V buttons Change a parameter Use Volume VOL value and buttons Go back to the Press MENU button Press Home button previous menu level Important If you have the wrong Main Menu showing you can quickly move to the other menu by doing the following e Press the Home or Menu button to return to normal viewing mode e Use the Channel buttons to move to an analog or a digital channel e Press the Home or Menu button again to display the Main Menu The Main Menu st
4. 1 w The warranty applies to the Cardio Theater product only while a it remains in the possession of the original purchaser and proof of purchase is demonstrated b it has not been subjected to accident misuse abuse improper service or mechanical electrical or non Precor modification c claims are made within the warranty period This warranty does not cover damage or product failure caused by electrical wiring not in compliance with electrical codes or Precor owner s manual specifications or failure to provide reasonable and necessary maintenance as outlined in the owner s manual This warranty excludes misuse or failures of for example poor quality CD s multiple discs inserted in the player failures caused by home produced copies of discs etc Except in Canada Precor does not pay labor outside the United States Warranties outside the United States and Canada may vary Please contact your local Dealer for details This Limited Warranty shall not apply to 1 2 3 O Software PROM version upgrades Normal wear and tear consumables and cosmetic items including but not limited to the following labels Repairs performed on Cardio Theater products missing a serial number or with a serial tag that has been altered or defaced Service calls to correct installation of the product or instruct owners on how to use the product Pickup and delivery involved with repairs Any labor costs
5. You should also make sure you are in analog TV mode an analog channel is showing when you are programming custom features An A appears before the number on analog channels Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 13 Automatic Power On Off Setup The Automatic Power On Off feature turns the PVS screen on automatically when headphones are inserted into the headphone jack At the end of the exercise session when the headphones are removed from the jack the screen turns off after approximately 10 20 seconds This feature is typically used to conserve power and lengthen screen life If this feature is enabled it overrides any other headphone detection features This procedure uses the standalone controller only The default for this feature is disabled 1 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming Make sure you are on an analog channel An A will precede the channel number Press both the Volume A and Channel A buttons simultaneously until the LED begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode If nothing happens try pressing both Volume A and Channel A buttons at the same time again Note While you are in Program Device mode if you do not press a button within 15 seconds the P
6. Broadcast Area Supported The PVS15DT supports ATSC standards in the North American broadcast market Product Recycling and Disposal This equipment must be recycled or discarded according to applicable local and national regulations Product labels in accordance with European Directive 2002 96 EC concerning waste electrical and electronic equipment WEEE determine the framework for the return and recycling of used equipment as applicable throughout the European Union The WEEE label indicates that the product is not to be thrown away but rather reclaimed upon end of life per this Directive In accordance with the European WEEE Directive electrical and electronic equipment EEE is to be collected separately and to be reused recycled or recovered at end of life Users of EEE with the WEEE label per Annex IV of the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste but use the collection framework available to customers for the return recycling and recovery of WEEE Customer participation is important to minimize any potential effects of EEE on the environment and human health due to the potential presence of hazardous substances in EEE For proper collection and treatment refer to Obtaining Service S y e A D r4 V gt Tl r4 N A Cc 0 e r4 N Radio Frequency Interference RFI Federal Communications Commission Part 15 WARNING To prevent fire or electrical sho
7. Important Equipment must be shipped with an RMA number in order for Cardio Theater to process it Any equipment received without an RMA number will be returned to the sender Operation and Maintenance Guide Before You Begin Programming the Standalone Controller for the PVS15DT Screen After you install the PVS hardware and complete all power and cable antenna connections you can turn on the PVS screen and program the channels and custom features First however the CNTE7 standalone controller must be programmed to support the PVS screen To program the controller for the PVS screen follow these steps These steps explain how to reset and program the controller 1 Turn on the PVS screen if it is not already turned on 2 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming You should always plug in headphones before doing any programming with the standalone controller 3 Using the Channel buttons move to any analog channel An A appears before the number You should perform any programming in analog TV mode 4 To make sure you start with all custom features set at their defaults perform a Master Reset of the controller Press both Volume A and Channel A buttons simultaneously until the LED 5 Press the Power button All features on the controller return to the factory defaults The Volume bar appears confirming the change For more information about rese
8. The Closed Caption On Off feature displays captioning only when it is available Important This feature is not available with PAL compliant PVS screens In addition you cannot use CC2 standard with this feature You cannot use the Closed Caption On Off feature with the Automatic Power On Off feature The Automatic Power On Off feature turns off the screen when headphones are unplugged from the headphone Jack This procedure uses the standalone controller only Important Do not use the remote control to turn off and on CC1 on the PVS screen using the Video Setup menu Doing so will affect the proper functionality of this feature The default for this feature is disabled 1 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming Make sure you are on an analog channel An A will precede the channel number Press both the Volume A and Channel A buttons simultaneously until the LED begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode Choose one based on what you want to do If you want to Then Press the Volume A button A Caption Off message appears Enable the feature Disable the feature Press the Volume button As soon as you press a Volume button the volume bar appears briefly confirming the entry Then th
9. The default channel for the Home button is channel 4 Note The Home button is always enabled with the programmed channel you cannot disable this feature 1 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming Make sure you are on an analog channel An A will precede the channel number Press both the Volume A and Channel A buttons simultaneously until the LED begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode Press the Source button one or more times to move to an analog or a digital channel You must be in the correct analog or digital mode for the channel you want to specify Specify the desired channel for the Home button To specify a digital channel such as 9 5 use Source for the hyphen For example you would enter 9 press Source and then enter 5 Press the Home button The Volume bar briefly appears confirming the entry Then the LED stops flashing and the PVS screen returns to normal viewing mode The channel you specified for the Home button displays on the screen Change the channel so the one you programmed for the Home button does not show Confirm that the Home button was properly programmed by pressing the Home button If the channel you programmed appears do nothing The programming is complete Otherwise repeat t
10. easily return to the Main Menu by pressing the Home or Menu button Operation and Maintenance Guide Manually Adding or Deleting Channels 1 2 Make sure the PVS screen is turned on Make sure the PVS is showing an analog channel An A appears before the number If needed use the Channel buttons to move to an analog channel You must have an analog channel showing to display the analog Main Menu Display the analog Main Menu as follows If you are using the Then Press both Volume and Channel buttons for 3 seconds Standalone controller Remote control Press the Menu button Because an analog channel was showing on the PVS screen the analog Main Menu appears You also enter Video Setup mode Move to Setup using the Channel W button and then select that option If you are using the Then Standalone controller Press the Power button to select it Remote control Press the SEL button to select it The analog Setup menu appears Important If your Main Menu has DTV Setup the digital Main Menu is showing The channel changed to a digital channel while you were entering Video Setup mode To move to the analog Main Menu press the Home or Menu button move to an analog channel and press the Home or Menu button again The analog Main Menu appears Then follow the instructions in step 4 to select Setup 10 5 At the analog Setup menu move to M
11. for the specified time frame and then the Home channel appears If the desired sequence happens then this feature is correctly enable However if this sequence does not happen repeat this procedure to correctly enable the feature Master Reset Feature Setup This feature returns the custom features on the standalone controller to the factory defaults You might use this feature if you are unsure how the custom features have been programmed Important You must reprogram the controller for the PVS screen whenever you reset all the custom features using the Master Reset feature Otherwise the standalone controller may not correctly operate the PVS screen See Programming the Standalone Controller for the PVS15DT Screen earlier for instructions This procedure uses the standalone controller only 1 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming 2 Make sure you are on an analog channel An A will precede the channel number 3 Press both the Volume A and Channel A buttons simultaneously until the LED begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode Press the Power button The volume bar appears confirming the change The LED stops flashing and the PVS screen returns to normal viewing mode All custom features return to the factory defaults
12. incurred beyond the applicable labor warranty period The user is cautioned that changes or modifications not expressly approved by the manufacturer of the product could void the user s authority to operate the product 28 Disclaimer and Release The warranties provided herein are the exclusive warranties given by Precor and supersede any prior contrary or additional representations whether oral or written ANY IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED ABOVE ARE LIMITED IN DURATION TO THE PERIODS OF EXPRESS WARRANTIES GIVEN ABOVE FOR THOSE SAME PARTS PRECOR HEREBY DISCLAIMS AND EXCLUDES THOSE WARRANTIES THEREAFTER Some States do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you PRECOR ALSO HEREBY DISCLAIMS AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES EXPRESS OR IMPLIED ARISING BY LAW OR OTHERWISE WITH RESPECT TO ANY NONCONFORMANCE OR DEFECT IN ANY PRODUCT INCLUDING BUT NOT LIMITED TO A ANY OBLIGATION LIABILITY RIGHT CLAIM OR REMEDY IN TORT WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS SUPPLIERS WHETHER ACTIVE PASSIVE OR IMPUTED AND B ANY OBLIGATION LIABILITY RIGHT CLAIM OR REMEDY FOR LOSS OF OR DAMAGE TO ANY PRODUCT This disclaimer and release shall apply even if the express warranty set forth above fails of its essential purpose Exclusive Remedies Fo
13. with the wire ties Use the pliers to tighten the wire ties so the controller cannot move Important Be sure to secure the controller so that it cannot move If the controller moves it may damage the exercise equipment as well as itself and void the Limited Warranty You do not need to disconnect the coiled power cable from the controller to perform this procedure 1 Cut the two wire ties holding the standalone controller to the ee i ire ti i ful not t equipment Remove the wire ties from the controller and toss Bp CUT GI hE exe es Paste romi ne wire ties DENY TATE u o leave any sharp edges on the wire ties Operation and Maintenance Guide Maintenance and Troubleshooting 26 Troubleshooting the PVS Table 7 may help you to understand and troubleshoot any problems that you encounter with the PVS screen and standalone controller If the suggestions in the table do not help you solve the problems that you encounter please contact Cardio Theater Technical Support Table 7 How to solve most problems Issue What to Do Bars on Try anew channel it may be station trouble Make sure screen video cable is connected to connector on the back of the PVS screen Check for local interference Poor TV Adjust Sharpness under the Picture menu in Main reception Menu Try a new channel it may be station trouble Make sure coaxial cable is securely connected to its connector on the back of the PVS screen C
14. Information Picture Color Temperature Contrast Default is 75 Brightness Default is 65 Color Default is 75 Sharpness Default is 80 Tint Default is O Sound Equalizer Balance 0 AVL Automatic Volume Level On Surround Off Mode Stereo 22 Main Menu Special Setup Second Level Blue Back Information Off Lets you change the background when there is no signal on a channel Auto Sleep Off With this feature turned on the screen will automatically switch to standby mode approximately 10 minutes after the TV program ends Childlock Off N A Caption Off Displays any captioning provided by the TV programming Parental Control Allows you to block unwanted TV programs based on different ratings Auto On On N A Reset Resets any changed values to their defaults Version Shown in the center of the menu Auto Program this displays the software version of the PVS screen Allows you to select the TV format and run automatic programming to set up channels You can set up both analog and digital channels with this option Manual Program If needed allows you to add and remove a channel Language Shows a list of languages available for this screen Input Lets you select the input you want to set up TV DTV or Video Operation and Maintenance Guide Using the Menus Digital Main Menu The digital Main Menu lets you set up and cus
15. LCD directly in front of the person rather than at a distance on the wall Volume buttons on the standalone controller allow a person to change the audio level Depending on how the PVS screen is configured Closed Captioning may appear allowing people to exercise without headphones The LED lights when the PVS screen is on and flashes to indicate programming mode Channel buttons let you move through the available channels Holding a button down rapidly scrolls through the channels Figure 1 shows the PVS15DT screen and CNTE7 standalone controller The PVS15DT supports both analog and digital programming Each type of programming has its own menu to allow you to set up the channels and customize the screen To access a menu the PVS screen must have the appropriate type of channel showing For example to display the analog Main Menu an analog channel must be showing to display the digita Main Menu a digital channel must be showing You can tell the difference between analog and digital channels because the screen briefly displays the channel number preceded by an A or D Power button turns the screen on and off Volume buttons let you adjust the audio level when using headphones Holding a button down rapidly changes volume Home button jumps to a predefined channel set by the facility Source button scrolls through analog TV mode digital TV mode and video mode Use to enter a hyphen when
16. Theater product deemed defective by a Cardio Theater representative will be issued a return authorization number Precor will not accept returns without a return authorization number Precor reserves the right at their option to repair or replace the product after verification of defect Product that fails after the warranty period expires will be repaired or replaced at the current part and labor pricing after authorization from the customer Repairs are warranted for 90 days Precor s obligations under this warranty are limited as set forth below Warranty Periods and Coverage e Cardio Theater Transmitters 3 Years Parts amp Labor xTV T Wireless or Wired Floor Models XTVFM system transmitter e Cardio Theater Receivers 1 Year Parts amp Labor XTV R Wireless or Wired Upper Models XTVFM system receiver Cardio Theater LCD Screen PVS 1 Year Parts amp Labor e Cardio Theater Screen Controllers 1 Year Parts amp Labor Quick Change Headphone Jack 90 Day Parts Only Optional DVD Player 1 Year Parts e CT Experience Series Screen PVS1 2 2 Years Parts amp Labor e CT Experience Series Screen Controller 2 Years Parts amp Labor CT Experience Series 900 amp 863 Receiver 2 Years Parts amp Labor e CT Experience Series Quick Change 90 Days Parts Only Headphone Jack Operation and Maintenance Guide Limited Warranty Conditions and Restrictions This warranty is valid only in accordance with the conditions set forth below
17. VS screen will time out and return to normal viewing mode Choose one based on what you want to do If you want to Then Enable the feature Press the Channel A button Disable the feature Press the Channel V button As soon as you press a button the volume bar appears briefly confirming the entry Then the LED stops flashing and the PVS screen returns to normal viewing mode To confirm that the PVS screen will turn off unplug the headphones and wait up to 20 seconds If the screen turns off the feature has been enabled If the screen does not turn off repeat this procedure to enable the feature Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 14 Home Button Feature Setup This feature lets you specify a channel that will appear when someone presses the Home button You can use this feature to allow people to quickly display an in house channel or special information channel with the press of a single button You can specify an analog or digital channel for the Home button However to program either channel you must have the correct TV mode showing either analog or digital Pressing the Source button during the process scrolls through analog digital and video modes If you enable the Inactivity Timer feature it will cause this channel to appear when the headphones are removed from the jack This procedure uses the standalone controller only
18. al Channel Setup screen appears when it Figure 2 Make sure you see the analog Main Menu starts to search for digital channels As the PVS scrolls through the list of analog channels each channel number appears on the screen When the PVS finds an analog channel with enough signal strength it changes the color 4 Move to Setup using the Channel W button and then select that option as follows If you are using the Then of the channel number Standalone controller Press th Power b tton to When the PVS searches for digital channels a bar shows the sel ct it percentage complete during the process Demols contral Press the SEL button to At the end of the process the lowest programmed channel odl ct i number appears on the screen Note You can stop the automatic programming process at any The analog Setup menu appears time as follows 5 At the analog Setup menu select Auto Program During the Then The Auto Program menu appears with Table highlighted Analog channel search process Press the Home or Menu button 6 At the Table option select the appropriate TV format mode for the PVS by using the Volume buttons to move to the appropriate Digital channel search process Press the Power or SEL mode Typically you would select the Cable STD mode button 7 Use the Channel V button to move to Start Operation and Maintenance Guide Initial Search for Channels 9 Manually Adding or D
19. anual Program and select it The Manual Program menu appears You will see the current channel displayed in the Channel field 6 Use the Volume buttons to specify the channel you want to add or remove The screen changes to that channel 7 Move to Skip using the Channel buttons and then change the setting as desired using the Volume buttons If you want the channel to Then select Appear Off Skip Off Not appear On Skip On so it will skip that channel 8 Move to the Memorize option using the Channel buttons and press the Power or SEL button to select that option 9 Press the Home or Menu button as needed to exit Video Setup mode and return to normal viewing mode 10 Use the Channel buttons to scroll through the channels to confirm that the channel has been added or deleted as desired Digital Instructions 1 Make sure the PVS screen is turned on 2 Make sure the PVS is showing a digital channel A D appears before the number If needed use the Channel buttons to move to a digital channel You must have a digital channel showing to display the digital Main Menu Operation and Maintenance Guide Manually Adding or Deleting Channels Display the digital Main Menu as follows If you are using the Then Standalone controller Press both Volume V and Channel buttons for 3 seconds Remote control Press the Menu button Because a digital channel wa
20. at are available After the feature runs the PVS screen displays only those channels that are available You can use either the standalone controller or remote control to perform this procedure Important To set up both analog and digital channels always use the automatic program feature from the analog Main Menu The channel setup feature on the Digital DTV Setup menu sets up only digital channels While you are using the analog Main Menu if you do not press a button or complete a sequence after a short period of time the analog Main Menu disappears and the PVS screen returns to normal viewing mode To exit from any menu screen you can press the Home button on the standalone controller or the Menu button on the remote control Each press of the Home or Menu button moves you back one menu until you reach normal viewing mode Note The Main Menu remains available for about 15 seconds after you return to normal viewing mode This allows you to easily return to the Main Menu by pressing the Home or Menu button if you happen to press the Home or Menu button too many times Operation and Maintenance Guide Initial Search for Channels Make sure the PVS screen is turned on Make sure you are on an analog channel An A will precede the channel number If needed use the Channel buttons to change the channel until you reach an analog channel You must have an analog channel showing to display the analog Main Menu Display the a
21. ays available for about 15 seconds after you exit to normal viewing mode allowing you to easily return to the menu by pressing the Home or Menu buttons 21 Analog Main Menu This section covers the analog Main Menu shown in 3 You use the analog Main Menu to set up and customize the analog channels on the PVS You should also automatically program both analog and digital channels using the Auto Program feature available through this menu The different features available through this menu are briefly explained in the tables Picture Sound Special Setup Position av Next 4 gt Exit TV AV Figure 3 The Analog Main Menu lets you customize analog channels Operation and Maintenance Guide Using the Menus Table 3 Analog Main Menu Main Menu Selection Description Picture Allows you to adjust contrast brightness and other features to improve the quality of the picture shown on the screen Sound Provides controls for changing the quality of the audio and adjusting audio through the speakers Special Provides access to features such as Closed Captioning and Parental Control You can also reset values that have been changed such as on the Picture menu If needed use this menu to determine the software version of the screen Setup Allow you to configure PVS analog channels Table 4 Second level menu for analog channels Main Menu Second Level
22. ck do not expose this equipment to rain moisture or excess heat The unit has been tested and found to comply with the limits for Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment The PVS generates uses and can radiate radio frequency energy and if not installed and used in accordance with the assembly installation and maintenance instruction manuals may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the unit does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into a separate outlet that uses a different circuit than the receiver Consult a Cardio Theater or an experienced radio TV technician for help WARNING Per FCC rules changes or modifications not expressly approved by Cardio Theater could void the user s authority to operate the equipment Operation and Maintenance Guide Important Safety Instructions Canadian Department of Communications The PVS does not exceed the Class A limits for
23. e LED stops flashing and the PVS screen returns to normal viewing mode Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 17 Promotional Information Content PIC Feature Setup The Promotional Information Content PIC feature lets you determine what a person sees when he or she starts to exercise With this feature enabled and a person plugs in headphones the controller immediately blocks any interaction with the buttons for a preset period the LED begins flashing slowly and the controller displays a predefined channel After the preset period passes the channel programmed for the Home button appears the controller returns functionality and the person can specify any desired channel You might use this feature to require people to see an information program about the fitness facility or a commercial You can program a digital or analog channel Note To specify a digital channel such as 9 5 press Source to enter the hyphen For example you would enter 9 press Source and then enter 5 This procedure uses the standalone controller only The default for this feature is disabled 1 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming 2 Make sure you are on an analog channel An A will precede the channel number 3 Press both the Power and Home buttons simultaneously until the LED begins flashing about 3 seconds Th
24. e flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode 4 Choose one based on what you want to do To Then Enable this feature with a factory preset delay of 15 seconds Press the Source button one or more times to display an analog or digital channel Specify the desired commercial channel Press the Home button The mute icon appears Do nothing for at least 20 seconds The LED will blink on the controller while it records updated settings Enable with delay that you specify Press the Source button one or more times to display an analog or digital channel Specify the desired commercial channel Press the Home button The mute icon appears Specify the desired time delay in seconds from 5 to 255 in one second increments using the number buttons Press the Home button again Disable this feature Press the Source button once The mute icon appears Press 0 Press Home button Do nothing for at least 20 seconds When the volume bar appears the feature has been programmed The LED stops flashing and the PVS screen returns to normal viewing mode Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 18 5 To confirm that this feature is correctly enabled unplug the headphones for 30 60 seconds then plug them in The specified channel should appear
25. eleting Channels Analog Instructions Sometimes if the signal for a channel is not strong enough the PVS screen may not catch it during automatic programming Follow these instructions to add a missed channel or delete an unwanted channel You will need to follow the appropriate procedure depending on the type of channel you want to add or delete An analog channel uses the analog Main Menu a digital channel uses the digital Main Menu Deleting an unwanted channel will not keep people from selecting it if they use the number buttons This process does not block access to that channel For example if you delete channel 125 and a person enters 125 with the number buttons that channel will appear on the screen However when a person uses the Channel buttons to scroll through the available channels channel 125 will not appear You can use either the standalone controller or remote control to perform this procedure While you are in a menu if you do not press a button or complete a sequence after a short period of time the menu disappears and the PVS screen returns to normal viewing mode To exit from any menu screen you can press the Home button on the standalone controller or the Menu button on the remote control Each press of the Home or Menu button moves you back one menu until you reach normal viewing mode Note The Main Menu remains available for about 15 seconds after you return to normal viewing mode This allows you to
26. esrnsnnennrennnnnnnnnrenrnnnnnenrnannnnnns 5 ai a a to Pg Obtaining Service sssssssssssssssisssissrsssrisrinsnenurnstnennrennnnninnnnnnnnnnnnnnnnnnna 6 Limited Warranty sssesscssssssssssssscssssecssssesssssseeessssecesssseeesesneeesens 28 Programming the Standalone Controller for the PVS15DT Screen sssssssssnunununununununununenennnnnunnnnnnnnnnnnnnnnn unnn nn nnnnnn nnn 7 Initial Search for Channels cscs 8 Manually Adding or Deleting Channels sssssssee 10 Using the Standalone Controller to Set Up Custom Features sssssssssscsssessssesserssseessessseessessses 13 Automatic Power On Off Setup esseceeseeseeeeeseseeeeesteeeeeees 14 Home Button Feature Setup 0 0 csssececessssssesesessssssseseesneeaseeeees 15 Inactivity Timer Feature Setup sssssssssssssesssseesseessesssseessens 16 Closed Caption On Off Setup onc eeesesesseceseseseeeeteteeeeeeeeeeees 17 Promotional Information Content PIC Feature Setup 18 Master Reset Feature Setup cssssecsessssesssesessseseeeseseasseeeees 19 Quick Reference to Custom Features sessies 20 Operation and Maintenance Guide Table of Contents 3 Before You Begin The Cardio Theater Personal Viewing System PVS adds personalized entertainment to workouts A person steps on the exercise equipment plugs headphones into the jack selects a TV program using the Channel buttons and begins exercising The program appears on a bright full color liquid crystal display
27. eted as desired Operation and Maintenance Guide Manually Adding or Deleting Channels 12 Using the Standalone Controller to Set Up Custom Features Cardio Theater has customized a number of features that are commonly used in a fitness facility The customization allows you to easily enable or disable a feature using the standalone controller Use of these features Is optional e Automatic Power On Off feature causes the PVS screen to turn off automatically when headphones are removed and turn on when headphones are inserted e Home Button feature lets you specify a channel that will appear when someone presses the Home button If the Inactivity Timer feature is enabled it will cause this channel to appear when the headphones are removed from the jack e Inactivity Timer feature causes the screen to display the channel configured for the Home button when headphones are removed from the jack This feature does not work when the Automatic Power On Off feature is enabled e Closed Caption On Off feature causes the screen to display Closed Captioning CC1 standard when no headphones are connected This feature does not work when the Automatic Power On Off feature is enabled This feature is also not available with PAL compliant PVS screens e Promotional Information Content PIC feature lets you require a person to watch a specific channel for a preset time before that person can use the controller to select a different program Yo
28. g solution directly on controllers Doing so could cause moisture to enter through the connector and damage the controller Operation and Maintenance Guide Maintenance and Troubleshooting Reprogramming the Standalone Controller To use the standalone controller with your PVS screen you will need to program the controller for that screen First you will need to determine the PVS software version which is typically listed on the analog Special menu You may need to use the remote control to access this information You should also perform a Master Reset of the features on the controller to return them to factory defaults To program the CNTE7 standalone controller for your PVS screen follow these steps 1 Determine the software version of the PVS screen You can check the software version on the Special menu see Using the Menus for information 2 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming 3 Make sure you are on an analog channel An A will precede the channel number 4 Perform a master feature reset as explained in Master Reset Feature Setup earlier in this guide 5 Press both Volume A and Power buttons simultaneously until the LED begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device Mode 25 6 Press anumber button based on the PVS scree
29. heck for local interference Ghosts in Try anew channel it may be station trouble Make sure picture coaxial cable is securely connected to its connector on the back of the PVS screen Check for local interference TV program Specify channel using 0 9 keys on the standalone cannot be controller or remote control If necessary rerun the watched Auto Program feature see nitial Search for Channels Issue What to Do No power Make sure the LED is lit on the screen and on the controller Check the power adapter to see if the green LED is lit lf Automatic Power On Off feature is enabled connect head phones to the jack No Closed Make sure Caption is On under the Caption feature in Captioning the analog Special menu or digital DTV Setup menu Closed Captioning may not be available on that channel try a different channel Closed A delay between captioning and the actual dialogue is Captioning is common in live broadcasts delayed Closed Reception is weak or poor signal strength which is Captioning is causing problems with the text display Try a new garbled channel Make sure cable is securely connected to its connector on the back of the PVS screen No picture Make sure PVS screen is fully plugged into a power outlet Push the Power button Try a new channel it may be station trouble Turn the PVS screen off and then turn it back on after one minute Poor picture Adjust controls such as Brightness Colo
30. hese steps to ensure the button is programmed correctly Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 15 Inactivity Timer Feature Setup This feature lets you program the screen to display the channel that is configured for the Home button when headphones are removed from the jack This allows the fitness facility to have an in house or informational channel showing when the equipment is not currently in use You cannot use the Inactivity Timer feature with the Automatic Power On Off feature The Automatic Power On Off feature turns off the screen when headphones are removed from the headphone jack This procedure uses the standalone controller only The default for this feature is disabled 1 Plug in headphones before proceeding to make sure that the screen does not turn off while you are programming 2 Make sure you are on an analog channel An A will precede the channel number 3 Press both the Power and Home buttons simultaneously until the LED begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode 4 Choose one based on what you want to do If you want to Then Enable with a e Press O or enter nothing factory preset time of e Press Channel A button to 15 seconds complete the entry Enable the feature e Specify the amount of time in minutes t
31. ion features such as the Inactivity Timer or Automatic Power On Off This guide explains how to set up the analog and digital channels It also explains how to program the custom features available through the Program Device mode gives an overview of the PVS menus and screens and covers any maintenance requirements For proper operation and maintenance please read this guide thoroughly and follow the instructions Important This guide covers PVS software version A1 x D1 x Your software may be different from that described in this guide The PVS15DT supports ATSC standards in the North American broadcast market Operation and Maintenance Guide Before You Begin Installation Information Fitness facilities can add a PVS screen to any Precor exercise equipment using an integrated bracket assembly The bracket assembly allows the PVS screen to be installed conveniently close to people exercising For exercise equipment from other manufacturers fitness facilities can use a stand designed to safely support the PVS screen and place the stand near the equipment The standalone controller is attached during installation it can be attached to the handlebars of almost any exercise equipment except those with handlebars that move The PVS screen receives power from a DC power block which is plugged into a standard AC power outlet It does not rely on power from the exercise equipment The standalone controller receives power from the PVS
32. legal theory Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Complete this portion and keep for your records Purchased From Dealer or store name Phone Number Dealer or store telephone number Product Model For example Transmitters Receivers Serial Number The serial number is found on the shipping container or item Effective 30 June 2006 P N CX30037 102 29 Notes Operation and Maintenance Guide 30 Notes Operation and Maintenance Guide 31 Notes Operation and Maintenance Guide 32 Cardio Theater Precor and EFX are registered trademarks and Cardio Theater PVS and Cardio Theater Quick Change Headphone Jack are trademarks of Precor Incorporated Copyright 2008 Precor Incorporated 4 H F il E R www cardiotheater com CARDIO A Division of Precor Incorporated NOTICE PVS15DT CNTE7 OMG CX30464 102 20031 142nd Ave NE Due to continuing advancements in technology Precor Incorporated reserves the right to make changes in Warranty Statement CX30037 102 Woodinville WA USA 98072 4002 hardware packaging and any accompanying documentation without prior written notice 15 January 2008
33. n with which this 2 Remove the two screws at the bottom of the controller with a controller will work Phillips head screwdriver See 5 For Then PVS15ATPTL version 1 1 and higher Press 1 PVS15ATPTL version 1 0 Press 2 PVS15PTL version 2 0X and higher Press 3 PVS15DTPTL Press 4 PVS15PCL Press 5 PVS15ATPCL version 1 1 or higher Press 6 Eve eee Remove these two The volume bar appears confirming the entry Then the LED Screws stops flashing and the PVS screen returns to normal viewing mode Figure 5 Remove screws holding headphone jack Replacing the Headphone Jack 3 Remove the headphone Jack When someone using a standalone controller experiences no sound 4 Insert a new headphone jack or poor sound quality such as intermittent sound or crackling you 5 Insert the two screws removed earlier and tighten snoule GEEA ine nbacpnone aec Ny MOH ine neacprione pugin 6 Insert two wire ties through the holes in the mounting bracket on the headphone jack If the problem continues the jack should be the back of the controller replaced 7 Place the controller on the neoprene mounting pad or rubber The controller is designed to make changing the headphone jack a quick and easy job one easily done at the facility You will need a Phillips head screwdriver wire cutter pliers and two new wire ties to reattach the controller adapter mounts and then attach it to the equipment
34. nalog Main Menu as follows If you are using the Then Press both Volume W and Channel buttons for 3 seconds Standalone controller Remote control Press Menu button The analog Main Menu appears on the PVS screen and you enter Video Setup mode If the channel changes while you are pressing the buttons on the controller generally you can continue with this process However the digital Main Menu may have appeared instead of the analog Main Menu Make sure your screen matches the analog Main Menu shown in Figure 2 Important If your Main Menu has DTV Setup the digital Main Menu is showing Press the Home or Menu button to exit the screen use the Channel buttons to find an analog channel and press the Home or Menu button again If you do this quickly while the controller LED is flashing you can bring up the analog Main Menu easily Then follow the instructions in step 4 Analog Main Menu shows 8 With Start highlighted begin the automatic search process as follows If you are using the Then Standalone controller Press the Power button to start Digital Main Menu This the process is not the menu you want Remote control Press the SEL button to start the process Position av Next 4 gt Exit TV AV The search process may take several minutes to finish The PVS searches for analog channels first and then searches for digital channels The digit
35. nnel Parental Control Allows you to block unwanted TV programs based on different ratings Caption Displays any captioning provided by the TV programming Input 24 Maintenance and Troubleshooting In general the PVS screen and standalone controller require little maintenance and will rarely experience problems once installed However you may find the information in this section useful The standalone controller is designed to handle use by many people in a fitness facility However in the unusual event that the standalone controller needs to be replaced you may need to program the controller so it supports your PVS screen This section explains how to program the controller for different PVS screens This section also explains how to replace the headphone jack when it no longer provides good audio quality Cleaning the PVS and Controller For the Precor exercise equipment follow the daily cleaning instructions and cautionary statements found in the Product Owner s Manual Periodically dust the PVS screen with a soft clean cloth CAUTION Do not use liquid cleaners or aerosol cleaners to clean the screen Do not use any solvents such as alcohol and paint thinner or acidic cleaners Each week clean the standalone controller with a mild soap and water solution Lightly dampen a soft clean cloth with the solution and wipe the controller Do not use too much solution on the cloth or spray cleanin
36. o allow before the screen changes to the channel set for the Home button Enter up to three numbers to specify the time from 1 to 255 minutes e Press the Channel A button to complete the entry Disable the feature Press the Channel V button without pressing any number button As soon as you press a Channel button the volume bar appears briefly confirming the entry Then the LED stops flashing and the PVS screen returns to normal viewing mode To confirm that the Inactivity Timer feature is enabled correctly unplug the headphones and wait the duration that you specified for the Home channel to appear If the Home channel appears as you specified the feature is correctly set up However if the Home channel does not appear in the time frame you specified repeat this procedure to correctly set it up Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 16 Closed Caption On Off Setup With this feature Closed Captioning CC1 standard displays on the screen when headphones are not plugged into the headphone jack Then when headphones are plugged into the jack the screen stops displaying Closed Captioning This feature gives people the choice of using headphones to hear the TV program or not using headphones but simply reading the captioning while they exercise Closed Captioning is provided by the TV programming Some TV programs may not provide Closed Captioning
37. r and Sharpness under the Picture menu in Main Menu No audio Increase the audio level with the Volume A button Check the headphone jack Replace the headphone jack if necessary Poor audio Re insert the plug into the headphone jack Try moving the plug in the jack to see if the sound improves Replace the headphone jack if necessary Operation and Maintenance Guide Maintenance and Troubleshooting 27 Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR CARDIO THEATER PRODUCT BY USING THE EQUIPMENT YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS Limited Warranty Precor Incorporated Precor warrants all new Cardio Theater products to be free from defects in materials and manufacture for the warranty periods set forth below The warranty periods commence on the invoice date of the original purchase This warranty applies only against defects discovered within the warranty period and extends only to the original purchaser of the product Parts repaired or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period only To claim under this warranty the buyer must notify Precor or your authorized Cardio Theater dealer within 30 days after the date of discovery of any nonconformity and make the affected product available for inspection by Precor or its service representative Cardio
38. r any product described above that fails to conform to its warranty Precor will provide at their option one of the following 1 repair 2 replacement or 3 refund of the purchase price Limited Warranty service may be obtained by contacting the authorized dealer from whom you purchased the item Precor compensates Servicers for warranty trips within their normal service area to repair commercial product at the customer s location You may be charged a trip charge outside the service area THESE SHALL BE THE SOLE AND EXCLUSIVE REMEDIES OF THE BUYER FOR ANY BREACH OF WARRANTY Operation and Maintenance Guide EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES PRECOR AND OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY WHETHER ARISING IN CONTRACT INCLUDING WARRANTY TORT INCLUDING ACTIVE PASSIVE OR IMPUTED NEGLIGENCE AND STRICT LIABILITY OR OTHERWISE FOR DAMAGE TO THE PRODUCT PROPERTY DAMAGE LOSS OF USE REVENUE OR PROFIT COST OF CAPITAL COST OF SUBSTITUTE PRODUCT ADDITIONAL COSTS INCURRED BY BUYER BY WAY OF CORRECTION OR OTHERWISE OR ANY OTHER INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE MISUSE OR INABILITY TO USE THE PRODUCT This exclusion applies even if the above warranty fails of its essential purposes and regardless of whether such damages are sought for breach of warranty breach of contract negligence or strict liability in tort or under any other
39. radio noise emissions from a digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada Table of Contents Important Safety Instructions ssssunsunnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnn 1 Using the Menus sssssssennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnna 21 Analog Main Menu sssssssssssesessrernesnennnsneureonnnennennnnnennnennnnnennennnnnnae 22 Broadcast Area Supported ssssssssssssssesssesssuanaaneeeeessnnens 1 Digital Main Menu sssssssssssssssesuenunssnenrnunsunesuneneeneonnnnenneounnneennennennnan 23 Product Recycling and Disposal sscscscssssssssssssecsesceesessseneees 1 Maintenance and Troubleshooting sss 25 Radio Frequency Interference RFI sssssusssrurssrereeesereneeereres 2 Cleaning the PVS and Controller esseseseseeseeesseteeeeeeees 25 Before You Begin ssssssssnsnsunenunnnnununnunununnnnununnunununnnnunannnnannn annman 4 Reprogramming the Standalone Controller sssaaa 20 i Replacing the Headphone Jack ou 26 Installation Information sssssssssssssssssssssrsssrnsnisnnsnnnnsnsnnnnnnnnnnnnnnnsnennnnns 5 Troubleshootina the PVS 97 Suggested Tools sssssssssssisssssessssrnssnsnr
40. s showing on the PVS screen the digital Main Menu appears You also enter Video Setup mode Move to DTV Setup using the Channel W button and then select that option If you are using the Then Standalone controller Press the Power button to select it Remote control Press the SEL button to select it The digital DTV Setup menu appears Important If the fourth option on the Main Menu says Setup the analog Main Menu is showing The channel changed to an analog channel while you were entering Video Setup mode To move to the digital Main Menu press the Home or Menu button use the Channel buttons to select a digital channel and press the Home or Menu button again The digital Main Menu appears Then follow the instructions in step 4 to select DTV Setup At the digital DTV Setup menu move to Channel Edit and select it The Channel Edit screen appears It shows a list of the available channels 11 6 For the channel you want to add or delete move to the Add column and change the setting as desired by pressing the Power or SEL button If you want the channel to Then Appear Make sure a check mark Vv appears Not appear Remove the check mark 7 Press the Home or Menu button as needed to exit Video Setup mode and return to normal viewing mode 8 Use the Channel buttons to scroll through the channels to confirm that the channel has been added or del
41. screen The coiled power cable is connected to the screen and controller during assembly For information about installing the PVS and standalone controller on equipment refer to the appropriate integrated bracket assembly instructions To install the PVS on a stand refer to the Personal Viewing System PVS Stand Assembly Instructions Suggested Tools The CNTE7 standalone controller lets you set up the PVS without any additional equipment However you may find some programming is easier with the optional remote control Contact your Cardio Theater dealer to order one or more remote controls as desired Obtaining Service Do not attempt to service any of the equipment except as described in this guide For information about product operation or service refer to the Cardio Theater web site at www cardiotheater com or contact an authorized Cardio Theater Technical Support Representative at 1 800 776 6695 or service cardiotheater com Representatives are available to serve you from 6 00 am to 5 00 pm Monday through Friday U S A Pacific Time Returning Equipment to Cardio Theater To return equipment to Cardio Theater for any reason you must contact Cardio Theater Technical Support and obtain a return authorization RMA number When requesting the RMA number explain why you are returning the equipment for example you ordered too many controllers and the extra controller can be returned to stock or the equipment needs repairs
42. second Press Volume A With 15 second delay Press a number button Press Power Channel A needed timer 1 Press Source as needed For Press 2 Specify desired 1 Press O 2 Specify channel e PVS15ATPTL 1 1 or higher 1 channel 2 Press Channel A 3 Press Home e PVS15ATPTL 1 0 2 3 Press Home 4 Do nothing until volume bar e PVS15PTL 2 0X or higher 3 With time specified appears e PVS15DTPTL 4 by you e PVS15PCL 5 1 Specify time in With delay specified by you e PVS15ATPCL 1 1 or higher 6 minutes 1 Press Source as needed PVS5 7 2 Press Channel A 2 Specify channel 3 Press Home 4 Specify time in seconds 5 Press Home Disable Press Cannot be disabled Press Channel Y Press Volume VW 1 Press Source N A N A Channel V default is channel 4 2 Press 0 3 Press Home 4 Do nothing until volume bar Operation and Maintenance Guide Using the Standalone Controller to Set Up Custom Features 20 Using the Menus You set up and customize the PVS screen using the Video Setup mode With the PVS15DT the Video Setup mode uses two different menu systems to support both analog and digital channels To access a menu the PVS screen must have the appropriate type of channel showing For example to display the analog Main Menu an analog channel must be showing to display the digital Main Menu a digital channel must be showing You can tell the difference between analog and digital channels because the screen briefly displays the channel number preceded by an
43. specifying a digital channel such as 9 5 Figure 1 Overview of PVS15DT screen and CNTE7 standalone controller Operation and Maintenance Guide Before You Begin Number keys let you enter specific channel numbers Headphone jack Note See Using the Menus for an overview of the analog and digital menus When you display a menu you enter Video Setup mode This mode should be reserved for the installing technician and select fitness facility personnel A number of custom features are available on the PVS that a fitness facility might want to use such as Automatic Power On Off Headphone Inactivity Timer and Home button You set these options using the Program Device mode which is available only through special button sequences from the standalone controller Similar to the Video Setup mode the Program Device mode should reserved for the installing technician and select fitness facility personnel Important See Using the Standalone Controller to Set Up Custom Features for instructions on programming the custom features A Quick Reference on page 20 steps you through the programming once you are familiar with the instructions The CNTE7 standalone controller includes a feature that gives a person the chance to quickly re insert the headphones if they become accidently disconnected If the headphones are re inserted within 15 seconds the standalone controller will not perform any of the custom headphone detect
44. tomize the digital channels This section covers the digital Main Menu shown in 4 The different features available through this menu are briefly explained in the tables Picture Sound Setup DTV Setup Position av Next 4 gt Exit TV AV Figure 4 Use the digital Main Menu to customize digital channels 23 Table 5 Digital Main Menu Main Menu Selection Description Picture Allows you to adjust color temperature contrast and other features to improve the quality of the picture shown on the screen Sound Provides controls for changing the quality of the audio and adjusting audio through the speakers Setup Lets you adjust the position of the display on the screen DTV Setup Allows you to configure PVS digital channels You can also set up parental control and closed captioning Operation and Maintenance Guide Using the Menus Table 6 Second level menu for digital channels Main Menu Picture Sound Setup DTV Setup Second Level Information Color Temperature RGB Contrast Default is 75 Brightness Default is 65 Color Default is 75 Sharpness Default is 80 Equalizer Balance 0 AVL Automatic Volume Level On Surround Off H Position V Position Reset Channel Setup Allows you to run automatic programming for digital channels only Channel Edit If needed allows you to add and remove a cha
45. tting the controller see Master Reset Feature Setup Press both Volume A and Power buttons simultaneously until the LED begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode To set the controller to support the PVS15DT press 4 The volume bar appears confirming the entry Then the LED stops flashing and the PVS screen returns to normal viewing mode Important You must reprogram the controller for the PVS screen whenever someone resets all the custom features using the Master Reset feature Otherwise the standalone controller may not correctly operate the PVS screen For more information about programming the standalone controller for PVS screens see Reprogramming the Standalone Controller later in this guide begins flashing about 3 seconds The flashing LED on the controller and the mute icon on the screen indicate that the PVS screen has entered Program Device mode Note While you are in Program Device mode if you do not press a button within 15 seconds the PVS screen will time out and return to normal viewing mode Operation and Maintenance Guide Programming the Standalone Controller for the PVS15DT Screen 7 Initial Search for Channels To program the channels on the PVS simply run the automatic program feature from the analog Main Menu This feature identifies both the analog and digital TV channels th
46. u might use this feature to show an informational program or commercial This feature occurs after headphones are inserted e Master Reset feature returns all custom features on the standalone controller to the factory defaults It also resets the PVS programming mode back to an analog PVS screen This section provides instructions for setting up the custom features At the end of this section you will find a table that provides a quick reference to the buttons you press Once you are familiar with setting up these features you may find the table is all you need To set up these features you access the Program Device mode using the standalone controller Depending on the feature you access this mode using a different combination of buttons Refer to the feature setup instructions or the quick reference for that sequence Note While you are in Program Device mode if you do not press a button within 15 seconds the PVS screen will time out and return to normal viewing mode You can set up only one custom feature at a time As soon as you program a feature or the screen times out the screen returns to normal viewing mode Important You must use the standalone controller to set up these features The remote contro accesses the standard PVS features not the customized Cardio Theater features Before programming any custom features always plug in headphones to make sure that the screen does not turn off while you are programming
Download Pdf Manuals
Related Search