2010 PRESTIGE PRO MANUAL 3-24-10
Contents
1. PRO SERIES Installation Instructions 36 105 000 BTU Professional Grill GBQRP36L 36 Grill GBQC36 36 Cart 42 112 000 BTU Professional Grill GBQRP42L 42 Grill GBQC42 42 Cart PLEASE READ THESE OPERATING INSTRUCTIONS BEFORE INSTALLATION AND USE TO PREVENT ACCCIDENT OR DAMAGE TO THE GRILL ATTENTION INSTALLER PLEASE LEAVE THESE INSTRUCTIONS WITH THE CONSUMER ATTENTION CONSUMER PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE If you have service or installation questions please call us at 1 800 358 8886 or visit our website at www prestige america com Safety Labels Appearing On The Appliance MODEL NO GBQRP36L 36 Grill GBQRP42L 42 Grill EQUIPPED FOR NATURAL GAS OR LP PROPANE GAS SERIAL No 000000 ANSI Z21 58 1995 CGA 1 6 M95 ANSI Z21 58A 1998 CGA 1 6 M98 ANSI Z21 58B 2000 CGA 1 6 M02 OUTDOOR COOKING GAS APPLIANCE FOR OUTDOOR USE ONLY IF STORED INDOORS DETACH AND LEAVE CYLINDERS OUTDOORS BURNER INPUT RATING LP AND NATURAL GAS GBQRP36L 36 Grill 30 000 BTU X 3 GBQRP36L 36 Grill BROILER 13 500 GBQRP42L 42 Grill 13 500 GBQRP42L 42 SMOKER BURNER 7 000 BTU GAS PRESSURE LP GAS PROPANE NATURAL GAS MANIFOLD 10 5 w c GBQRP36L 5 0 we GBQRP42L 5 0 w c MINIMUM SUPPLY 11 0 w c 5 0 w c TO REGULATOR ELECTRICAL REQUIREMENT 12 VDC OPTIONAL ROTISSERIE IS PROVIDED WITH A SEPARATE POWER SUPPLY CORD AND IS NO2. gt Wear proper clothing when operating appliances Loose fitting or hanging garments should never be worn while using the grill gt Do not leave the grill unattended while in use gt Do not use water on grease fires A violent steam explosion may result Smother the fire with a dry chemical or foam fire extinguisher Safety and Installation Instructions UNIT INSTALLATION gt Your Prestige Pro Series Grill comes pre assembled and requires very little set up We do however recommend the use of professional help during the installation of your unit as improper installation may affect your warranty gt Remove the unit from the carton along with all accessories and check that no damage has occurred to any parts or the unit gt Burners Check the U shaped burner tubes and remove any obstructions that may be in the ports or holes Using cold water and a brush will be sufficient Make sure all foreign particles are removed from the burner before use Make sure the air shutter on the burners is slightly opened to about 1 8 WARNING For proper operation burners must be aligned with the valve orifice and seated in the bracket slot This is accomplished by first placing the burner tube shutter hole securely over the valve orifice and then sliding the burner bracket into the positioning slot Care should be exercised to maintair he burner hole orifice mating assembly gt Igniters
3. This gas grill must be installed in accordance with all local codes If installation is planned in an area with no local codes the gas grill must be installed in accord with the National Fuel Gas Code ANSI Z223 1 and storage and handling of liquefied petroleum gases ANSI NFPA 58 or CSA B149 1 natural gas and propane installation code CALIFORNIA PROPOSITION 65 WARNING The burning of gas cooking fuel generates some by products which are on the list of substances which are known by the State of California to cause cancer or reproductive harm California law requires businesses to warn customers of potential exposure to such substances To minimize exposure to these substances always operate the unit according to the use and care manual ensuring you provide good ventilation when cooking with gas GRILL LOCATION VV v v V Do not use or locate your gas grill in garages porches breezeways sheds enclosed areas or under overhead unprotected combustible construction Do not store or use your grill or gas tanks indoors this gas grill is designed for outdoor use only This gas grill cannot be used on or in recreational vehicles or boats Clearances to combustible materials must be a minimum of 24 from the back and 24 on each side The grill must be installed using only non combustible materials Do not obstruct the flow of combustion and ventilation air around the grill housing Refer to minimum clearances stated above and
4. WHAT TO DO Contact a qualified professional to correct Clean burners per manual Check installation per manual Warranty Registration Prestige 25 Riverside Drive Pine Brook New Jersey 07058 CUSTOMER SERVICE 1 800 358 8886 info prestige america com VISIT US AT www prestige america com DATE OF PURCHASE DATE OF INSTALLATION SERIAL NUMBER MODEL CUSTOMER INFORMATION NAME STREET ADDRESS CITY STATE AND ZIP CODE TELEPHONE NUMBER PLEASE RATE THE CONDITION OF YOUR GRILL AT TIME OF DELIVERY EXCELLENT VERY GOOD GOOD POOR ANY ADDITIONAL COMMENTS OR PRODUCT SUGGESTIONS THANK YOU FOR PURCHASING YOUR GRILL FROM US Installation Instructions Appliance cut out dimensions WIDTH DEPTH HEIGHT GBQRP36L 36 34 1 4 23 1 16 10 3 16 GBORP42L 42 40 1 2 23 1 16 10 3 16 d y DE i gt E 5 Met E ir f ri 7 HEIGHT Important please verify by measuring actual appliance from box measure twice cut once
5. Before placing the flame spreader shields and briquettes in place make sure the igniter electrode is positioned 3 16 away from the burner tube and located over the port hole in the burner Adjust if necessary CONNECTING TO THE GAS SOURCE Make sure all of the knobs are in the OFF position For Natural Gas Units Attach a 5 8 flared fitting to the grill and connect to the gas stub with a quick disconnect or threaded fitting to match the stub diameter Do not use rubber hosing The connecting pipe must be at least inside diameter with gas fittings and must not exceed three feet in length You must install the gas regulator supplied Some of the above components must be purchased separately Please use a professional installer to connect the gas compliant with applicable LA W codes Leak check all connections using the soapy solution test detailed in the manual Safety and Installation Instructions For Liguid Propane Gas Units The regulator supplied by the manufacturer must be used in the installation Attach regulator hose to the pipe connection at the rear of the unit Tighten with a wrench but do not over tighten Install the LP tank Make sure the tank is securely positioned in an upright position and will not fall over Do not operate the unit unless the tank is in an upright position Leak check all connections using the soapy water solution test detailed in the manual To connect insert the regulator inlet to the tank va
6. The supply line must be sized and installed to provide a sufficient supply of gas to meet the maximum demand of the grill without undue loss of pressure A 3 4 ID is recommended The sealant used on threaded joints of gas pipe must be of a type resistant to the action of LP and Natural gas It is also recommended that no more than 36 of flex line be used in the installation CHECKING FOR GAS LEAKS gt Never test for leaks with a lighted match or any other type of flame gt Prior to first use at the beginning of each new season or after changing or refilling the gas cylinder you must check for gas leaks Follow these steps to check for gas leaks I Make a soapy solution by mixing one part liquid detergent and one part water 2 Turn off control valves Turn gas on at the source 3 Apply the soapy solutions to all gas connections Bubbles will appear in the soap if the connections are not properly sealed 4 Tighten the connections if necessary 5 Repeat step 3 and 4 until no bubbles appear 6 If you have detected a gas leak that you cannot repair turn off the gas at the source disconnect the fuel line and call your dealer or gas supplier for assistance ELECTRICAL PRECAUTIONS Extension cords are available and may be used if care is exercised in their use If an extension cord is used the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of
7. cooking surface when lighting or operating the grill Use barbecue tools with wood handles and insulated oven mitts when operating the grill IF YOU SMELL GAS I Shut off the gas supply to the appliance at its source 2 Extinguish any open flames 3 Open grill hood to release any accumulation of gas vapor 4 If a gas odor persists contact your gas supplier immediately Gas Specifications Be sure that the gas supplied to the grill conforms to the model you purchased A Natural Gas grill requires natural gas to operate an LP grill requires liquid propane gas to operate Check the rating label on the bottom left side of the back of the unit Never connect the appliance to an unregulated gas supply line Grills operated without a regulator are unsafe and will not be serviced until installed properly and safely unsafe operation without a gas regulator will void warranty of the grill Grills operated with NG natural gas gas must be installed with the NG regulator supplied with the unit set to 5 0 water column pressure gt gt gt Safety and Installation Instructions Grills operated with LP liquid propane gas must be installed with an LP regulator supplied with the unit set to 10 5 water column pressure The gas valves used in the grills are preset at the factory for Natural Gas or Liquid Propane operation Please contact your dealer and use a licensed contractor or installer to convert your grill to a diff
8. if the flame is lifting off the ports or it has yellow color at the flame tips If the flame is lifting loosen the shutter locking screw and turn the shutter clockwise to reduce air intake If the flame has yellow tips loosen the shutter locking screw and turn the shutter counterclockwise to allow more air in the gas air mixture This will stabilize the flame After adjusting the flame be sure the shutter locking screw is retightened Lighting Instructions WHEN THE BURNERS WILL NOT LIGHT PROBLEM Air in the line Low gas pressure Burner orifice clogged Gas supply is OFF Gas line is blocked No spark Shutter air mixture Igniter broken Igniter dirty Light is not on 11 Burner not seated properly YELLOW OR ORANGE FLAME PROBLEM 1 Obstruction in the gas line 2 Dust or dirt in burner holes 3 Improper installation of unit WHAT TO DO Contact a qualified professional to correct Check pressure and make sure a regulator is installed correctly check for proper pipe ID Contact a qualified professional to correct Turn ON the gas Contact a qualified professional to correct Check igniter gap per manual Check the battery Adjust air shutters per manual Call Service and have igniter replaced Clean igniter of dirt or grease with cloth and water Connect 115 VAC power to rear of unit Turn switch on Check bulb replace if necessary per manual Seat burner properly per instructions in manual
9. the appliance and the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally or touch hot surfaces Outdoor extension cords should be used with outdoor use products They are surface marked with suffix letters W or W A and with a tag stating Suitable for Use with Outdoor Appliances To protect against electrical shock the power cord and plug should be kept dry and off the ground Do not clean this product with water spray do not spray cleaners into the lamp socket area Do not operate any appliance with a damaged power cord or power plug or after the appliance malfunctions or has been damaged in any manner Return the appliance to the nearest authorized service facility for examination repair or adjustment Safety and Installation Instructions gt This appliance conforms to all uniform electrical safety codes and electrical grounding regulations install unit to LA W local codes or in their absence with National Electrical Code ANSI NFPA 70 or CSA C22 1 GENERAL USE AND CARE The manufacturer can not be held responsible for damage or injury caused by improper use of this appliance Be certain your appliance is properly installed and grounded by a qualified technician in accordance ith applicable codes To guarantee the electrical safety of this appliance continuity must exist between he appliance and an effective grounding s
10. valve and make sure it is secure and not leaking With the control knobs in the OFF position turn on the cylinder valve gt If you smell gas or hear a hiss of gas escaping from the tank get away from the tank and do not attempt to correct the problem yourself Call the Fire Department immediately gt If your grill has no leak at the cylinder then recheck for loose connections and retest for leaks using the method detailed in the following pages with soapy solution gt Do not subject your LP gas cylinder to excessive heat and always store the cylinder in an upright position Never store your LP cylinders indoors Make sure that when attaching components all connections are secured and fully tightened to prevent leakage gt If one is not already available it is recommended that an ON OFF shutoff valve be installed at the gas supply source and that the gas supply be turned off when either Natural Gas or LP Gas grills are not in use Safety and Installation Instructions The outdoor gas grill and its individual gas shut off valve must be disconnected from the gas supply piping system before any pressure testing of that system at test pressures equal to or greater than 1 2 Psig 3 5 kPa The outdoor gas grill must be isolated from the main gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply system at test pressures equal to or less than 1 2 Psig 3 5 kPa
11. S APPLLANCE IS EQUIPPED WITH A THREE PRONG GROUNDING PLUG FOR PROTECTIO AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED DIRECTLY INTO A PROPERL GROUNDED RECEPTACLE DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG DIELECTRIC TESTED GAS LEAK TESTED Table of Contents Congratulations on the purchase of your Prestige Pro Series Grill These products were designed and developed by AMD Direct Inc in partnership with Prestige the premier manufacturer and distributor of high quality outdoor products This grill meets or exceeds the requirements of ETL as intended for outdoor use This product carries a limited lifetime warranty on all stainless steel parts and components with a one year warranty on all other components SAFETY LABELS APPEARING ON THE APPLIANCE 3 IMPORTANT INSTRUCTIONS FOR SAFE INSTALLATION AND OPERATION 5 IF YOU SMELL GAS 6 FILLING AND REFILLING LP GAS CYLINDERS 7 CHECKING FOR GAS LEAKS 8 GENERAL USE AND CARE 9 UNIT INSTALLATION 10 CONNECTING TO THE GAS SOURCE 10 LIGHTING YOUR GRILL 12 TROUBLESHOOTING 12 FIRST TIME OPERATION 13 ROTISSERIE amp SEAR BURNER 14 HALOGEN LIGHTING 14 CLEANING 15 BURNER ADJUSTMENTS 16 WHEN THE BURNERS WILL NOT LIGHT 17 YELLOW OR ORANGE FLAME 17 WARRANTY REGISTRATION 18 APPLIANCE CUT OUT DIMENSIONS 19 WIRING DIAGRAMS 20 Safety and Installation Instructions When using your Prestige Pro Series grill please read and follow these basic precautions GRILL INSTALLATION
12. T CONSIDERED A PART OF THIS UNIT FOR RATING PURPOSES A DO NOT STORE A SPARE LP GAS CYLINDER UNDER OR NEAR THIS APPLIANCE B NEVER FILL THE CYLINDER BEYOND 80 PERCENT FULL C IF THE INFORMATION IN A AND B IS NOT FOLLOWED EXACTLY A FIRE CAUSING DEATH OR SERIOUS INJURY MAY OCCUR FOR INSTALLATION IN NON COMBUSTIBLE LOCATIONS ONLY DO NOT LOCATE UNDER OVERHEAD UNPROTECTED COMBUSTIBLE SURFACES FOR INSTALLATION IN COMBUSTIBLE LOCATIONS AS A FREESTANDING UNIT WITH CLEARANCES OF 24 FROM THE SIDE WALLS AND 24 FROM THE REAL WALL SIDE BURNERS P N P10030 Safety Labels Appearing On The Appliance YOUR GRILL IS EOUIPPED WITH A BATTERY OPERATED IGNITION SYSTEM FOR EASIER LIGHTING OF YOUR GRILL THE SYSTEM USES SIMPLE 9 VOLT BATTERIES READ THESE GRILL AND ROTISSERIE LIGHTING INSTRUCTIONS BEFORE LIGHTING KEEP THE GRILL HOOD OPEN DURING THE LIGHTING PROCESS MAKE SURE ALL THE BURNER KNOBS ARE TURNED TO THE OFF POSITION PUSH IN AND TURN THE KNOB TO THE HIGHEST POSITION SETTING PRESS THE IGNITION BUTTON IN AND HOLD UNTIL THE GRILL BURNER IGNITES IF IHE BURNER DOES NOT IGNITE WIIHIN 5 SECONDS TURN THE BURNER TO THE OFF POSITION AND WAIT 5 MINUTES REPEAT THE ABOVE STEPS TO SAFELY SHUT DOWN THE GRILL TURN ALL BURNERS TO THE OFF POSITION FOR LP GAS MODELS IN ADDITION TO TURNING THE BURNERS OFF TURN THE VALVE ON THE GAS CYLINDER TO THE OFF POSITION WHEN NOT IN USE WARNING ELECTRICAL GROUNDING INSTRUCTIONS THI
13. erent gas type The self contained LP system barbeque grill is design certified to be used with a standard 20 Ib 12 1 4 diameter 18 high cylinder with fight handed connection threads The cylinder must be marked in accordance with the latest U S Department of Transportation specifications for LP gas cylinders DOT CFR49 or National Standards of Canada CAN CSA B359 Cylinders Spheres and Tubes for the Transportation of Dangerous Goods The LP hose supplied by the manufacturer has a shut off valve as part of the hose assembly and should be turned to the OFF position when not in use LP TANK REQUIREMENTS a collar to protect the cylinder threads on the customer supplied tank an arrangement for gas vapor withdrawal a safety relief device having direct communication with the vapor space of the cylinder a method of mounting when not in use the tank shut off valve should be turned off Filling and Refilling LP Gas Cylinders WARNING All purging and refilling of LP gas cylinders must be performed by qualified personnel in the LP gas industry Never store a spare LP gas cylinder under or near this appliance Never fill the LP gas cylinder beyond 80 percent full Failure to follow these instruction may result in explosion personal injury or death Turn control knobs and cylinder valve to the OFF position Unscrew valve Remove cylinder and have it filled at your local qualified propane dealer Once filled carefully connect the
14. keep free and clear of debris Safety and Installation Instructions Please read all instructions before installing or operating your gas grill to prevent injury and appliance damage All gas grills will get hot during use Use extreme caution when operating the grill Do not touch hot surfaces Always use the handle to open or close the grill Close supervision is necessary when this or any appliance is used near children Keep children away from the grill during operation and until the grill has cooled off Do not store any LP cylinder or tank not connected for use with the grill in the area of this grill or any other appliance Never store an LP cylinder or tank indoors or within the reach of children Keep any electrical supply cord and fuel supply hose away from any heated surfaces and dripping grease Do not twist the gas supply hose Before each use visually inspect the gas supply hose for cracks cuts or excessive wear Replace the hose if necessary Never test the grill for gas leaks using a lighted match or any other open flame see leak test procedures using soap water solutions included in following pages of this manual The use of accessories regulators or components not recommended by the appliance manufacturer may cause injuries and will void warranty Never light the grill with the hood closed and be certain that the burners are positioned and seated over the gas valves and on the burner support Never lean over the
15. lve and turn the black coupler clockwise until the coupler tightens securely Do not over tighten the coupler connection To disconnect turn the tank valve OFF hold the coupler sleeve and turn it counterclockwise gt Upon completion of assembly turn the tank valve on and turn the control valves on the grill to the HIGH position for 10 to 15 seconds to purge the line of air and fill the line with gas CAUTION JM SH BERI Sn EG and protect all fuel fittings gt Cooking Component Installation Important Prior to first use clean and rinse all removable components Lighting Instructions gt Caution Never operate the grill unattended Do not operate the rotisserie or Sear Zone burner with the hood closed Prior to using your grill make sure all of the following is correctly completed Verify that the burner tube is free of insects and insect nests webs etc Verify installation of the proper gas type and regulator settings Verify that the proper gas connection is complete Minimum clearances are maintained All packaging has been removed All parts and components are properly in place That an installer supplied manual gas shut off valve is fully accessible Ras RARR IE IR Clean and inspect LP hose for cuts wear abrasion or leaks Replace if necessary with a suitable UL ETL or CSA Listed part with internally threaded connector LIGHTING YOUR GRILL O Become familiar with the safety instructions at the fron
16. nce a week when using the grill it is suggested that you wash the grates in a mild soap and warm water solution Use a brash or steel wool to clean the grates Rinse with cold water Cleaning the Sear Plates O When using the grill at least once a week remove the sear plates and clean them with a warm soapy water solution and a scrub brush Rinse with cold water Cleaning the Burner Tubes and Ports O Itis important that the gas control knobs are in the OFF position and the fuel line is disconnected from the unit when cleaning the burners O To reduce the possibility of flashback please use the following procedures at least once per week during heavy grill use to keep the burners clean and at least once per month during times of low usage to keep spiders and webs out of the system Remove the grates briquettes and sear plates from the grill Carefully scrub the burners in place with a scrub brush and soapy water Use a paper clip to clean out the port holes in the burners P P DE Be careful not to damage the igniter while performing this function Cleaning the Grease Tray O The grease tray should be removed emptied and then washed in a mild soap and warm water solution Rinse with cold water Do not put sand aluminum foil or any other material in the grease tray at any time Cleaning the Grill Surfaces O To clean the exterior of the grill use a stainless steel cleaner and wipe down thoroughly with a sponge or cloth Never u
17. or Sear Zone burner with the hood closed This may damage the grill WARNING The electric rotisserie motor is equipped with a three pronged grounding plug for your protection against shock hazard It should be plugged directly into a properly grounded three prong receptacle Do not cut the grounding pin from the plug This outdoor cooking gas appliance must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 or the Canadian Electrical Code CSA C22 1 WARNING Never touch the cold or hot halogen bulb with fingers as this may damage the bulb or result in severe injury Your grill comes with ceramic briquettes to be spaced evenly on the supplied briquette trays Two boxes are delivered with the unit More briquettes can be purchased from your dealer or Prestige at your request The briquettes add flavor provide more even heat and will assist in burning off food drippings Maintenance Instructions As with all appliances proper care and maintenance will keep your gas grill in good operating condition and prolong its life By following these cleaning procedures on a regular and timely basis your grill will be clean and working properly with minimum effort Cleaning the Top Grates and Sear Grate O After cooking tum the knobs to the OFF position and let the grill cool down before attempting to clean the grates O Before first use and at least o
18. se aluminum foil anyplace in or on your grill O Wipe in the direction of the grain of the stainless steel with a non abrasive cleaner p g Warranty Registration PLEASE NOTE THE FOLLOWING If you have purchased a Prestige Pro Series Grill you must supply your own three pronged grounded extension cord to use the halogen light This extension cord must be rated for outdoor use All natural and LP gas units require the customer to install the gas regulator supplied with the unit on the unit Installation without this regulator will void the warranty Have a qualified installer complete the work Do not install rubber hose to connect the grill Gas piping must be 1 2 minimum diameter and the gas line requires a gas shut off valve Check all connections using the soapy water solution and test techniques described in this manual When using an LP tank the tank must be purged of any air build up or the unit will not function A qualified person must purge the tank of all excess air Please when operating the control knobs push in and then turn the knobs slowly counterclockwise to the desired position These push in and turn valves are industry standard design for improved operating safety To turn off the burners push in and turn the knob slowly to the off position BURNER ADJUSTMENTS The flame on the burner should occur over the full length be blue and stable not flickering The air intake shutter should be adjusted only
19. t of this manual Do not smoke while lighting the grill or checking the gas supply connections O Make sure that all gas connections are securely tightened and have been leak tested with a soapy water solution never with a flame READ THESE GRILL AND ROTISSERIE LIGHTING INSTRUCTIONS BEFORE LIGHTING POSITION AND WAIT 5 MINUTES REPEAT THE ABOVE STEPS TO SAFELY SHUT DOWN THE GRILL TURN ALL BURNERS TO THE OFF POSITION FOR LP GAS MODELS IN ADDITION IO TURNING THE BURNERS OFF TURN THE VALVE ON THE GAS CYLINDER TO THE OFF POSITION WHEN NOT IN USE O If the burner still does not light refer to the manual and make sure the unit is set up properly before calling for service O Warranty work in not provided for customer education on the operation of the unit TROUBLESHOOTING O Make sure the battery is operational The grill ignition system uses 9 Volt batteries and prolonged exposure to heat when not is use will disable the battery Batteries are not covered under any warranty O If your grill fails to properly light wait five minutes and repeat the above procedures Lighting Instructions Make sure that there is no obstruction in your gas lines Make sure your unit is equipped with a gas regulator Make sure the igniters are gapped correctly Make sure the burners are clean and no ports are clogged 00000 To light a burner manually follow the steps above and light a long fireplace match and place the ma
20. tch through the flame spreaders and the elongated hole down to the burner ports then turn on the gas valve O If the unit still does not work consult your dealer or call Prestige at the numbers listed on the front of this manual Flashback may occur in or around the burner tubes Flashback exhibits a characteristic whooshing sound Immediately turn off your burners then remove and clean them with soap and water and a brush until all foreign objects are removed First Time Operation MAIN BURNERS Before cooking with your grill the first time burn off any foreign matter and rid the unit of any odors by operating the unit for about five minutes The flame should have a bluish color to it It may have a tint of yellow and adjustment to the air shutters can be made to obtain a blue flame and proper gas flow Although the grill can be operated with the hood closed fired by the U shaped burners for short periods of time 5 10 minutes do not operate the rotisserie or Sear Zone burner with the hood closed This may damage the grill The grill should be preheated with the front panel main burner control settings on HIGH for five minutes with the hood closed Temperature Settings Use HIGH burner setting for searing heavy cooking preheat and clean up Use other burner settings to create temperatures to fit your personal cooking preferences Temperatures may vary with outside temperature and wind conditions You can cook poultr
21. y and larger cuts of meat slowly if you turn OFF the burner directly under the food and use adjacent burners to supply heat When cooking fattier foods cooking with indirect heat also greatly reduces flare ups Fats and juices that drip down can cause flare ups Since some flare up does impart a distinctive and desirable flavor taste and color to foods being grilled they should be carefully and reasonably encouraged Uncontrolled or excessive flare ups however will damage your food Lighting Instructions CAUTION If the burners should go out during operation turn OFF the gas supply at the source and turn OFF all gas valves Refer to the lighting procedures to restart your grill Should a grease fire occur in your grill turn OFF the gas supply at the source turn OFF all burners and close the hood until the fire goes out Do not attempt to disconnect any gas fitting while your grill is in operation ROTISSERIE amp SEAR ZONE The rotisserie and Sear Zone system uses radiant heat of the infrared burner to cook food About five minutes after the burner is lit it will radiate a red orange colored glow The rotisserie motor is mounted on the left side of the grill The motor is equipped to rotate a maximum of 25 Ibs of meat or poultry and comes with a 30 long electrical cord Although the grill can be operated with the hood closed fired by the U shaped burners for short periods of time 5 10 minutes do not operate the rotisserie
22. ystem It is imperative that this basic safety requirement be met The manufacturer cannot be held responsible for damages caused by the lack or inadequacy of an effective grounding system Installation repair and maintenance work should be performed by an authorized service technician ork by unqualified persons could be dangerous and will void the warranty Before installation o service disconnect the power supply to the work area by removing the fuse tripping the circuit breaker or unplugging the unit Gasoline lighter fluid or other flammable liquids and vapors should never be stored in the area of this erill or any other appliance Do not store anything in the grill Make sure food is not forgotten in the grill forgotten items could melt or catch fire when the appliance is turned on To prevent injuries do not use accessories not recommended by the manufacturer Always open the grill hood carefully using only the handle as the hood may be hot gt Before cleaning the appliance trip the circuit breaker and allow the appliance to cool Children should not be left alone or unattended in an area where any appliance is in use They should never be allowed to touch sit or stand on any part of the appliance Do not store items of interest to children in cabinets above or in the grill Children climbing on the appliance to reach these items could be seriously injured
Download Pdf Manuals
Related Search