Gyration Ultra Cordless Optical Mouse
Contents
1. you are installing three or more devices on a single receiver see Installing 3 or More Devices on page 9 4 Using Ultra Mouse on the Desktop The Ultra mouse provides great flexibility in how you control your computer and its optical sensor allows for precise tracking on virtually any surface for optimal performance avoid highly reflective glass or mirrored surfaces To use on the desktop 1 Set up and synchronize the mouse with the Receiver see page 4 2 Remove the fully charged mouse from the charging cradle and place it on a flat surface The LED light on the receiver base will flicker rapidly when communicating with the mouse handset 3 Use the mouse like a standard desktop mouse In addition to its optical sensor Ultra mouse features an advanced reflective sensor that detects when the mouse is being lifted off the desktop To conserve battery life this sensor powers on the Gyro and shuts down the optical sensor each time the mouse is picked up Ultra mouse uses standard Windows and Mac mouse drivers Cursor tracking speeds mouse double click speeds and other options can be customized using the Mouse Control Panel under Windows 98 2nd ed 2000 ME XP or Mac OS 8 and above see OS documentation for further information about customizing mouse properties Tip For optimal battery life avoid using the Ultra mouse on dark colored surfaces Using Ultra Mouse in the Air The Ultra mouse has no line of sight req2. Gyration Ultra Cordless Optical Mouse User Manual Gyratian Spec System Requirements Product Specifications Ultra Cordless Optical Mouse RF Receiver m Full functionality on Mac and IBM compatible PCs running Windows 98 2nd ed 2000 ME XP or higher m Available USB port m CD ROM drive for GyroTools installation with Ultra Professional model m Microsoft or Mac compatible mouse driver no additional drivers to install Size 4 8 L x 2 0 W x 1 8 H 12 2cm x 5 1cm x 4 5cm 5 L x 4 W x 2 H 13cm x 10cm x 5cm Weight 5 3 oz 150g with battery pack 4 ounces 124g Operating Range Ultra Up to 25 feet 7 6m typical with no line of sight requirement Ultra Professional Up to 100 feet 30 5m typical with no line of sight requirement N A Radio 49 MHz U S with 8 channels and 36 800 security addresses N A Batteries m NiMH battery pack additional spare NiMH battery included with Ultra Professional model m 3 AAA batteries AAA battery clip included with Ultra Professional model only N A Connector N A USB with 5 1 5m cable Operating Temp 10 to 40 C 50 to 104 F Storage Temp 30 to 70 C 86 to 158 F Gyration Ultra Cordless Optical Mouse Identifying the Parts LED Indicator Scroll Wheel and Button _ Battery Pack j Battery Ralart Button A Channel Button d Actha
3. Learn mode If the receiver is not manually taken out of Learn Mode it will automatically return to Normal Mode after five minutes Status LED The Status LED displays useful information about modes of operation and the connection between receiver and transmitter s m The Status LED remains off when the receiver is operating in Normal Mode and no devices are transmitting m The Status LED flickers rapidly when the receiver is operating in Normal Mode and a 7 synchronized device is transmitting If there is radio interference the flickering light will be inconsistent m The Status LED blinks slowly 1 blink per second when the receiver is in Learn Mode and is awaiting a Teach instruction from a device m The Status LED blinks rapidly for a 4 second burst when it is in Learn Mode and processing a Teach instruction and synchronizing the receiver with the device Keyboard Status LEDs The Keyboard Status LEDs will indicate whether your computer has the Num Lock Caps Lock and or Scroll Lock features activated Conflict LED If an unrecognized Gyration device is attempting to operate on the same channel as a device that has been synchronized the red Conflict LED on the receiver will flicker and input control may be intermittent The Conflict Light will only detect interference from another Gyration RF device i e not cordless phones personal radios etc Installing 3 or More Devices The Receiver can be t
4. atus light on the Receiver will blink rapidly for 4 seconds then will blink slowly Push the TEACH button on any additional devices i e keyboard or 2 4 mouse at this time 5 OPTIONAL To exit Learn Mode press the LEARN button on the Receiver for 2 seconds Other wise after five minutes Learn Mode will automatically time out If more than one Gyration device is being installed on the system place the Receiver into Learn Mode step 3 above only once then Teach each device before exiting Learn Mode Do not push the Learn button on the receiver for each device to be added See Installing 3 or More Devices on page 9 When the Receiver is put into Learn Mode it erases its memory of learned devices and looks for new devices Therefore when adding a new device to a system it is necessary to put the Receiver into Learn Mode then Teach all devices that will be used on the system Note After the Teach Learn sequence is performed the Receiver and the device will remain synchronized after powering down and or changing channels It is only necessary to perform the Teach Learn sequence when setting a device up for the first time or when adding additional devices to the system Determining Which Channel Ultra Mouse is Using The Ultra mouse has multiple channels available to it To determine which channel a device is currently using 1 Press and quickly release the CHANNEL button on the bottom of the mouse handset 2 Co
5. aught to recognize up to eight devices mice remotes keyboards etc on a system but only two of those devices may be used simultaneously When setting up a system with a single receiver and 3 or more devices the following guidelines must be followed m Select two channels that are free of outside interference and install all devices on either of those two channels When possible it is recommended that the two chosen channels be separated by at least one unused channel m Any of the devices installed on one channel may be used simultaneously with any of the devices on the other channel Two devices that share a channel may not be used simultaneously When installing the devices try to determine which devices will be used simultaneously and set them on opposite channels The following example describes a single receiver system with two mice and a keyboard that requires one mouse to be used by a presenter for cursor control while another presenter inputs data on the keyboard Mouse 1 is set to channel 3 and the keyboard and mouse 2 are set to channel 5 With this configuration mouse 1 and the keyboard can be used simultaneously but mouse 2 and the keyboard cannot Note Gyration carries both a consumer and professional line of RF products Please note that a low power consumer device i e Ultra mouse with 25 ft range should not be used simultaneously with a high power professional device i e RF Keyboard with 100 ft range One or both
6. devices may not work properly if data is being transmitted by the two units at the same time For optimal simultaneous performance it is recommended that you use two low powered devices or two high powered devices If you wish to use both a high and low power device simultaneously it is recommended that you alternate usage between the devices Contacting Gyration If you have any questions on your new Gyration product please use any of the phone FAX numbers or addresses below Main Office Sales Gyration Inc Phone 800 316 5432 Toll free in US and Canada 12930 Saratoga Avenue Bldg C Fax 408 351 4433 Saratoga CA 95070 E mail sales gyration com USA Phone 408 255 3016 Technical Support Fax 408 255 9075 Phone 408 973 7086 E mail support gyration com World Wide Web www gyration com Warranty Information Gyration products come with a two year hardware warranty Gyration Inc Gyration warrants products against defects in material and workmanship for a period of two years from the date of purchase from Gyration or an authorized Gyration agent This warranty applies only to the original purchaser and is not transferable This warranty does not cover any incompatibilities due to the user s computer hardware software or any other related system configuration in which the product interfaces Proof of purchase will be required before any warranty consideration by Gyration occurs This warranty does not cover any damage caused by
7. lectronic devices e g monitor speakers radio etc 3 Raise receiver antenna and or uncoil USB Receiver cable When pressing the activate Batteries are low button the LED on the mouse is flashing When pressing the activation Batteries are dead trigger the LED on the mouse Replace or recharge batteries See page 3 recalibration is off Cursor moves too fast or too Speed or acceleration not Change the cursor tracking speed in the mouse control slow set properly panel See OS documentation for details Cursor drifts on the screen Sensor may require Place the mouse on the desk for 4 or more seconds to steady the cursor Troubleshooting Tips Continued Symptom Reason Solution Mouse LED does not flash in Dirty contacts Clean the contacts on bottom of mouse eect oo mouse Improper battery installed Make sure that the AAA battery pack is not installed End of life battery Replace battery Inadequate battery life Mouse used on dark colored Use mouse on light colored surface to minimize battery surface drain Gyration RF Receiver F Conti LED a r Leam Batian H Rebas Status LEDs Status LED Learn Button Pressing the LEARN button for 2 seconds puts the receiver into Learn Mode allowing you to synchronize one or more devices with the receiver After devices have been synchronized pressing the LEARN button again for 2 seconds takes the receiver out of
8. negligence non authorized modifications or parts installed without prior written permission from Gyration This warranty does not apply if the product has been damaged by accident abuse misuse or misapplication nor as a result of service to the product by anyone other than by Gyration Gyration is not responsible for any lost profits lost savings or other incidental or consequential damages arising out of the use of or inability to use this product This includes damage to property and to the extent permitted by law damages for personal injury This warranty is in lieu of all other warranties including implied warranties of merchantability and fitness for a particular purpose Some states do not allow limitation of implied warranties or exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights You may have other rights which may vary from state to state This warranty applies only to these products and is governed by the laws of the State of California
9. ng radio emitting devices Fine tuning Cursor Control The Ultra mouse uses your standard Windows mouse driver There are no additional drivers to install Any settings that are available to a standard desktop mouse are also available to Ultra mouse Multiple factors will determine how you adjust your mouse to suit your preference including screen resolution mouse driver version and overall personal preference While becoming familiar with your mouse and getting a feel for the GyroPoint method of cursor control Gyration recommends adjusting your mouse driver to the following settings m Pointer Speed Average Some new users prefer this setting to be slightly slower than average Advanced users will increase the speed so that less wrist movement gives them more screen coverage with the cursor m Acceleration Low or Off Troubleshooting Tips Solution Perform a Teach Learn sequence See Setting Up and Synchronizing Ultra Mouse and the Receiver on page 4 Symptom Reason Mouse LED comes on when Mouse and Receiver not activate button is pressed synchronized but receiver is unresponsive When using in air cursor is Gyro not activated visible but shows no move ment Squeeze or double click trigger on bottom of mouse Cursor movement is choppy Radio interference or erratic 1 Change the device s channel setting See Changing the Channel Ultra Mouse is Using on page 5 2 Move receiver away from other e
10. s Click any button to wake the mouse from sleep mode Using an In line Charger The NiMH battery pack can also be charged using an in line charger included with the Ultra Professional model and available for purchase as add on accessory 1 Connect power adapter to inline charger and plug into power source 2 Place battery pack into charger cradle to begin charging LED indicator on cradle will light solid Using an Alkaline Battery Clip A standard alkaline battery clip may also be used with your mouse included with the Ultra Professional model and available for purchase as add on accessory 1 Insert 3 AAA batteries into battery clip 2 Attach battery clip to mouse by snapping into place Note 1 AAA batteries are not recharged when the unit is placed in the charging cradle 2 If an alkaline battery clip is installed the Ultra mouse enters a sleep mode when left on the desk top for 4 or more hours Click any button to wake from sleep mode Setting Up and Synchronizing Ultra Mouse and the Receiver 1 Make sure the mouse is fully charged 2 Power on your computer and connect the Receiver s USB cable into an available USB port on your computer Follow standard USB device installation screens 3 Press and hold the LEARN button on the Receiver for 2 seconds The STATUS light will blink slowly indicating that the receiver is in Learn Mode 4 Press the TEACH button located on bottom of the mouse handset The st
11. tion Trigger Installing and Charging the Batteries The Ultra mouse comes with an NiMH battery pack already installed but you will need to remove the plastic insulator tab located inside the battery compartment This clear plastic tab prevents the battery from dis charging until you are ready to use your mouse 1 Press release button on the end of the mouse and lift battery pack off 2 Remove and discard plastic tab 3 Replace battery pack by snapping into place Using the Charging Cradle I mportant Your mouse must be charged for 9 hours prior to first use To charge your mouse 1 Be sure that the NiMH battery pack is properly installed 2 Connect power adapter to charging cradle and plug into power source 3 Place mouse handset into charging cradle LED on cradle will light solid LED indicator on mouse will flash slowly while batteries are charging and maintain a steady glow when fully charged 2 Note When a full charge is not required you may remove the mouse from the charging cradle at anytime you do not need to wait for the LED to stop flashing Low Battery Warning When battery drops to 20 of a full charge the LED indicator on the mouse will blink intermittently when transmitting data To optimize the performance of your NiMH battery it is best to recharge after every day of use Power Saving Sleep Mode To conserve power the Ultra mouse enters a sleep mode when it is left on the desktop for more than 24 hour
12. uirements so it s not necessary to point the device at the computer receiver or monitor Find a comfortable relaxed position and move the cursor with easy wrist movements 1 Set up and synchronize the mouse with the Receiver see page 4 2 Hold the mouse in a comfortable relaxed position with your index fin ger on the ACTIVATION TRIGGER and your thumb at the base of the scroll wheel see illustration 3 Press and hold the ACTIVATION TRIGGER with your index finger While holding the ACTIVATION TRIGGER flex your wrist up down sideways in a manner similar to using a flashlight The mouse cursor tracks the motions of your hand 4 Use your thumb to press the left right mouse buttons or to operate the scroll wheel Double click the ACTIVATION TRIGGER to keep the cursor continuously active To stop the cursor click the ACTIVATION TRIGGER once Powering Off Ultra Mouse 1 Simultaneously press and release the CHANNEL button and TEACH button on the bottom of the unit The mouse will immediately enter deep sleep mode and will be unresponsive to button clicks The unit will confirm it is powering off by flashing its LED three times 2 Repeat this sequence to power the unit back on The unit will confirm it is powering on by flashing its LED for 1 second Note Powering off the mouse prevents battery drain when traveling It may be necessary to power off the unit when traveling on commercial airlines due to FCC regulations regardi
13. unt the number of times the red LED on the bottom of the handset or the green LED on the top of the handset flashes The number of flashes indicates the channel the handset is using Changing the Channel Ultra Mouse is Using When two devices are being used in the same proximity each device should be set to operate on a unique channel For best reception space the channels apart by one or more channels For example setting the channels to 2 and 4 is recommended over setting the channels to 2 and 3 To change the channel 1 Press and hold the CHANNEL button on the bottom of the mouse handset for 2 seconds 2 When you release the button the mouse will change to the next channel and the red LED on the bottom of the handset and the green LED on the top of the handset will flash The number of flashes indicates the new channel the handset is using If a Teach Learn sequence has already been performed it will not be necessary to re synchronize the devices after a channel change Note If the mouse s channel is changed when the computer is powered down or the receiver is not connected the devices will become unsynchronized When the system is running click and release the channel button as described above to confirm the channel The mouse broadcasts a message across all eight channels that informs the receiver what channel it is currently operating on The receiver then automatically restores synchronization Tip If
Download Pdf Manuals
Related Search