PHOTOELECTRIC DUAL BEAM DETECTOR R4222
Contents
1. PPS WANNY Terminal Strip Identification The diagrams below represent the terminal strips on the receiver and transmitter and can be used for reference for connections RECEIVER TRANSMITTER Wiring Terminals Wiring Terminals POWER POWER COM N C NOT USED N O TAMPER TAMPER Q SWITCH SWITCH Wiring the Photo Beams to GTO PRO and Mighty Mule Gen 3 blue or green Gate Opener Control Boards models listed below To Pos Terminal of Battery To Neg Terminal of Battery 12 Volt Battery with Dual Spade Connectors SSS or other 12Vdc source INTERIOR TOP OF TRANSMITTER INTERIOR TOP OF RECEIVER Double Spade Tongue Connectors Transmitter Receiver Connections 1 Connect 1 and 2 power terminals of the transmitter to the 1 and 2 power terminals of the receiver 2 Connect 1 and 2 power terminals of the Receiver OR Transmitter to the battery 3 Connect 3 and 5 terminals of the receiver to the COM and SAFETY terminals on the control board CE RECEIVER CONTROL INPUTS Connections for PRO 2000XL PRO 3000 PRO 3000XL PRO 4000 PRO 4000XL MM 500 Control Boards Wires from Photo Beams Wiring the Photo Beams to Mighty Mule FM 350 Gate Opener Control Board To Pos Terminal of Battery To Neg Terminal of Battery 12 Volt Battery with Dual Spade Connectors SS or other 12Vdc source2. INTERIOR TOP OF TRANSMITTER INTERIOR TOP OF RECEIVER Double Spade Tongue Connectors 1 Connect 1 and 2 power terminals of the transmitter to the 1 and 2 power terminals of the receiver Transmitter Receiver Connections 2 Connect 1 and 2 power terminals of the Receiver OR Transmitter to the battery 3 Connect 3 and 5 terminals of the receiver to the COMMON and SAFETY terminals on the control board Wires from Photo Beams Wiring the Photo Beams to GTO PRO GP SL100 and GP SW100 Gate Opener Control Boards To Pos Terminal of Battery To Neg Terminal of Battery 12 Volt Battery with Dual Spade Connectors SSS or other 12Vdc source INTERIOR TOP OF TRANSMITTER INTERIOR TOP OF RECEIVER Double Spade Tongue Connectors 1 Connect 1 and 2 power terminals of the transmitter to the 1 and 2 power terminals of the receiver Transmitter Receiver Connections 2 Connect 1 and 2 power terminals of the Receiver OR Transmitter to the battery 3 Connect 3 and 5 terminals of the receiver to the COM and SAFETY terminals on the control board CUT TO USE 3 BUTTON STATION Wires from Photo Beams Wiring the Photo Beams to GTO PRO FM700 702 PRO SL1000 2000 and PRO SW1000 2000 Gate Opener Control Boards To Pos Terminal of Battery To Neg Terminal of Battery 12 Volt Battery with Dual Spade
3. CATORS beams are aligned OFF when beams are ale g g g g g oe g g oe el not aligned Refer to operation instructions LEVEL LED green ON indicates pace O oO Q 2o a GOOD LEVEL ALARM received signal Brightness varies depending on how well beam is aligned POWER LED green e ALARM LED red ON indicates beam ON when light beam blocked Use when setting response time is transmitting Refer to operation instructions Adjusting Optical Axis with a Voltmeter If you have a voltmeter the best method of adjusting the opti cal axis is to measure the signal level at the test probe points 1 Insert the voltmeter probes into the test points on the side of the receiver 2 Adjust the horizontal angle and vertical angle until the voltage is at maximum Test Points 3 If a voltage of 1 2v or above cannot be reached the for Voltmeter transmitter and or receiver should be readjusted Beam Interruption Time Adjustment Adjusts the amount of time between the beam being broken and the normally open relay closing Adjust time adjustment dial from 1 detecting fast moving objects to 5 detecting slow moving objects depending on your type of application and environment Fast Moving Objects Moving Objects Beam Interruption Time Adjustment VERIFY CORRECT OPERATION Condition Indication Transmitter i After installation confirm correct operation by suitable walking tests Ref
4. Connectors SS SS Cf c or other 12Vdc source INTERIOR TOP OF TRANSMITTER INTERIOR TOP OF RECEIVER Double Spade Tongue Connectors Transmitter Receiver Connections 1 Connect 1 and 2 power terminals of the transmitter to the 1 and 2 power terminals of the receiver 2 Connect 1 and 2 power terminals of the Receiver OR Transmitter to the battery 3 Connect 3 and 5 terminals of the receiver to the GRN and ORG terminals on the control board ACCESSORY RCVR Wires from Photo Beams e Beam Alignment Adjusting Optical Axis with the Viewfinder 1 Remove the RECEIVER and TRANSMITTER covers Be careful not to drop screw and nut and make sure power is connected 2 Adjust the horizontal pivot and the vertical adjustment screw using the built in viewer Look through the viewfinder on either side and adjust to put the oppposite sensor in the middle of the cross hairs in the view finder The GOOD LED should be on Adjust the light axis until the indication lamp is on lan Viewfinder v location Viewfinder Pe Vertical ii Adjustment Screw seNe To Raise To Lower Horizontal Adjusting Bracket e The brighter the Green LEVEL LED the more precise the alignment of the beams e GOOD LED green Use when adjusting beam alignment ON when TRANSMITTER INDICATOR RECEIVER INDI
5. Z N PROFESSIONAL ACCESS SYSTEM PHOTOELECTRIC DUAL BEAM DETECTOR Owners Manual R4222 The GTO PRO Photoelectric Dual Beam Detector uses dual beam and through beam technology to reduce false detections when detecting obstructions When the beams detect the presence of a moving object the detection will cause the gate s to stop and reverse to the fully open position As long as the beam is obstructed the gate s will remain open Not compatible with solar powered gate operators For use with use with all GTO PRO and Mighty Mule AC and DC powered gate operators PARTS DESCRIPTION Connection Terminals Wiring Knockout Response Time Adjustment COVER only for receiver Indicators Signal Level Test Points Tamper Switch LE Sight Hole Horizon Vertical N Alignment tal Angle Adjusting Screw ae Bracket Se SF Cover Lens Locking Screw INTERNAL VIEW OF RECEIVER For more information on GT0 s full line of automatic gate openers and access controls visit our website at www gtoinc com GTO e 3121 Hartsfield Road Tallahassee Florida 32303 800 543 4283 www gtoinc com Technical Service 800 543 1236 R4222 rev 11 6 07 2007 GTO Inc Printed in China for GTO Inc o Installation Overview Diagram illustrates correct placement of photo beams in relation to the gate Exterior placement e of Photo Beams __ placed outside of
6. er to the appropriate LED indicator during the walking test and ensure the gate opener operates in the correct manner Beam Not Blocked GOOD and LEVEL LEDs are ON Receiver Beam Blocked ALARM LED is ON TROUBLESHOOTING Symptom Possible Cause Remedy Transmitter LED does not light Improper voltage supplied Check the power supply and wiring Receiver LED does not light Improper voltage supplied Check the power supply and wiring 1 Beams reflect to the receiver by other objects Both beams are not blocked simultaneously Beam interruption time is too short Alarm LED does not light even when beams are blocked When the beams are blocked the receiver LED light is ON but not alarm Wiring is short circuited Wiring connection is not good The alarm indication lamp of receiver is always on There are obstructions between the transmitter and the receiver The outer covers are dirty Intermittent Alarm detection Bad wiring Fluctuating power supply voltage Optical axis is not properly adjusted 1 Remove the reflecting object or change optical axis direction 2 Block both beams 3 Increase beam interruption time adjustment Check wiring and connection spot 1 Adjust the optical axis 2 Remove the obstructions 3 Clean with window cleaner and a soft cloth Check wiring Check the power supply Remove the obstruction or relocate Fix the mounting Adjust the
7. ly so nut doesn t fall Wiring Hole 4 Mount the detector on the wall and run the wire through the wiring location in the wall 3 Remove the rubber knock out and pull the wire through Wiring Location In Wall BACK OF COVER 1 Feed the wire through the pole 2 Remove the Photo Beam cover as shown above in step1 3 Fix the base plate on the bracket Feed the Wire Through The Pole Pole Mounting Plate Fixed Regular Ring e Back to Back Installation Refer to the figure above NOTE Pole may be purchased at your local hardware store Connecting Photo Beams to GTO PRO and Mighty Mule Control Boards NOTE DO NOT use with solar panels A Make sure the power switch to the opener is turned off before connecting safety device wiring fo the terminal blocks Unplug ging the transformer does not turn power to the opener OFF Connecting wires to the terminals normally open wiring e Wire with 16awg minimum RB509 e 300 ft 91 4m max length e Be sure to capture the wire ends under the wire clamp plates e Avoid frayed ends on wires that might produce a short circuit e Be careful not to overtighten the screws as this may strip the threads in the plastic Terminal ii Terminal Terminal y Sp P Wire Block Wire Block Wire Block Correct Wrong Wrong
8. optical axis Adjust interruption time or change installation position If your experiencing false detections then increase the time adjustment by 1 increment at a time until the photo beam functions as desired Intermittent blockage between the transmitter and the receiver The receiver or transmitter is unstable Blocked by other moving objects Beam interruption time out of adjustment SPECIFICATIONS MODEL R4222 Infrared photoelectric Detection Method 98 4 ft 30m Range ICT For optimal efficiency wipe the outer cover frequently with a soft damp cloth Not compatible with Solar Panels Tamper Switch N O contact is open when cover is removed transmitter and reciever 66lbs 300g Both transmitter and receiver PC Resin Black
9. path of gate A vu 2 2 or x 7 x A x S 2 QS Vehicular Gate aN a 4 Interior placement __ of Photo Beams placed outside of path of gate Mounting Cautions Be sure that the optical axis is never obstructed The optical axis is both the vertical and horizontal range of detection or beam between the transmitter and receiver Do not mount the detector in the following conditions Ss amp Where obstructions plants fences etc Where the mounting Where sunlight and headlights shine are between the receiver and the sender surface is unstable directly into the front of the receiver i it Receiver Beam Alignment Up Down Direction meoo E Range 20 10 Receiver Transmitter E Z T When using more than one set make WY sure to alernate the transmitters D S Horizontally 180 i detectors as aia amp The optical axis can be fine tune a a Uia aa oe and Toit pases vertical direction N A N A Sensing Area Wall Mounting 1 Loosen the cover 2 Remove the rubber holding screw but DO NOT knockout and use the Screw Hole REMOVE NOTE BE screw holes to mount a CAREFUL NOT TO DROP the unit THE NUT THAT ACCOMPANIES SCREW Now remove the outer cover slow
Download Pdf Manuals
Related Search