PoE - VoIP Supply
Contents
1. Warranty information is available at www CyberData net Web http Awww cyberdata net support warranty index html 2010 CyberData Corporation ALL RIGHTS RESERVED 930353A Quick Reference Installation Quick Reference singlewire enabled CyberData VolP V2 Loudspeaker Amplifier POE 011116 The Singlewire enabled VoIP V2 Loudspeaker Amplifier is compatible with InformaCast Version 4 0 and higher IP Addressing DHCP IP Address 10 10 10 10 Web Access Username admin Web Access Password admin Subnet Mask 255 0 0 0 Default Gateway 10 0 0 1 a Default if there is not a DHCP server present Getting Started e Download the Singlewire enabled VoIP V2 Loudspeaker Amplifier Operations Guide PDF file from the Documents page at http www cyberdata net products voip digitalanalog singlewireloudspeakerampv2 docs html e Create a plan for the locations of your paging amplifiers e Prior to installation consult local building and electrical code requirements V2 Loudspeaker Amplifier Parts 1 Wall Mounting Kit 3 6 Plastic Anchors 3 6 x 1 1 4 inch Pan Head Phillip Screws ayAssemby 1 Enclosure View Inside of the Enclosure Quick Reference 930353A 2010 CyberData Corporation ALL RIGHTS RESERVED Features DIP Switch Settings iy _ s DIP Switches OFF ON 72. 0 Z PI E Js O DIP Switches RTFM Switch To broadcast a V2 Loudspeaker Amplifiers current IP address press the RTFM switch on the V2 Loudspeaker Amplifier for one second and then release the switch to hear the IP address announcement To restore the factory defaults complete the following steps 1 Press and hold the RTFM switch for eight seconds The V2 Loudspeaker Amplifier will announce the words restoring defaults and then announce the words rebooting 2 Release the RTFM switch The V2 Loudspeaker Amplifier settings will be restored to the factory default settings Power LED GREEN BLUE The power LED is a steady green in low power mode and a steady blue during high power mode The power LED will only blink either during a boot up or a phone call Status LED GREEN A steady LED confirms that the V2 Loudspeaker Amplifier is oper ational The LED will blink during a page when it is online Network Activity LED GREEN Network Link LED GREEN YELLOW Speaker Volume User Hardware Dip Switch and Jumper Settings Dimensions and Mounting Template 1 2 3 4 Note High power PoE mode con
3. Connections 1 Sense 2 GND 3 Relay COM 4 Relay NO 5 Line In U1 6 Line In 7 Line Out Line Out Connection 8 Line Out Note The Button Relay and Line In features are not supported with the Singlewire firmware o 9 Spkr Out Speaker Connection 1 10 Spkr Out Note Line Out is 10k Ohm at 2Vpp Speaker output is 8 Ohm Mounting the Enclosure To mount the enclosure 1 Prepare holes for the screws 2 Plug in the power adapter and use the green Power light to verify that the power is on Plug the Ethernet cable into the VoIP V2 Loudspeaker Amplifier The yellow Link light verifies the network connection For wall mounting use the three 6 x 1 1 4 inch Pan Head Phillip screws to secure the speaker 071057A 931032 6 PLASTIC ANCHOR 3x UNV eeu 151014 6x1 1 4 PAN HEAD PHILLIP SCREW 3x Contacting CyberData Corporate Headquarters Sales 831 373 2601 ext 334 Support 831 373 2601 ext 333 CyberData Corporation Web http www cyberdata net support contactsupportvoip html 2555 Garden Road RMA Dept 831 373 2601 ext 136 Monterey CA 93940 USA Email RMA CyberData net RMA Status http www cyberdata net support rmastatus html Phone 831 373 2601 Fax 831 373 4193
4. forms to IEEE 802 3at draft 3 0 OFF N A ON OFF 2010 CyberData Corporation ALL RIGHTS RESERVED 930353A Sets PoE for 802 3af class Not applicable for power setting Switch mode current set to LOW Low gain amplifier setting Quick Reference 6 281 159 54 Dimensions are in Inches Millimeters l 14 500 368 30 7 938 7 201 63 l B 10 875 276 23 al Dimensions are in Inches Millimeters L l j a ie 4 375 111 13 i i A Cable Grommets 3 PLCS dk 1 ar Quick Reference 930353A 2010 CyberData Corporation ALL RIGHTS RESERVED
Download Pdf Manuals
Related Search