Quickstart Guide: DM-TX-200-C-2G-FLOOR/DM-TX-200
Contents
1. screws 2009211 Connection to DM Receiver Room Controller External Power Pack DM 8G Output Connection Required DM TX 200 C 2G FLOOR and DM RMC 100 C Shown DM TX 200 C 2G FLOOR Installation into Floor Box Connect the DM OUT port of the transmitter to the DM 8G input of a DM switcher receiver room controller or other DM TX 200 26 FLOOR Rear Panel DM TX 200 C 2G FLOOR DM device If connecting to a DM switcher connect the ee transmitter to the DM IN port of a DMC C DMC C DSP input ON Floor Box card of the switcher Not Included For DM 8G wiring up to 330 feet 100 meters between devices use any of the following cables sold separately ON e Crestron DM CBL 8G DigitalMedia 8G cable A e Crestron DM CBL DigitalMedia cable EN CA 7 e Crestron DM CBL D DigitalMedia D cable pb 2 6 32 X 3 4 e Generic CAT5e or better UTP or STP s apoo k eS E Truss Combo Head Screws 4 2009211 NOTE Shielded cable and connectors are recommended to safeguard against unpredictable environmental DM RMC 100 C electrical noise which may impact performance at resolutions above 1080p Power Connection NOTE Connecting the 24 VDC 2 pin terminal block is not required if the transmitter is to be powered using Power over DM PoDM If the transmitter is not to be powered using PoDM connect the 2 pin terminal block to the included power pack Ground Connection Connect2. the DM TX 200 C 2G FLOOR DM TX 200 C 2G WALL depends on the way the transmitter is configured within the DigitalMedia system Audio Input Connection Using an unbalanced 3 5 mm TRS mini phone jack cable not included connect the AUDIO IN port to an unbalanced audio source e Ifthe transmitter is connected to a receiver room controller the transmitter a p uses its own configuration settings The transmitter ships with DHCP HDMI Input Connection q HOMO Ore gt enabled however the default IP address can be assigned by holding Using an HDMI cable not included connect the HDMI IN down the SETUP button while the unit boots up The default IP address is port to the HDMI output port of an audio video source 192 168 1 239 The default IP address overwrites the current setting e Ifthe transmitter is connected to a DM switcher the transmitter is automatically configured by the switcher f suv ray PC Input Connection Using a VGA cable not included connect the PC IN port to an RGB VGA component S video or composite video source If manual configuration of the IP address of the transmitter is desired use Crestron Toolbox to set the IP address LAPTOP Crestron the Crestron logo Crestron Toolbox DigitalMedia DigitalMedia 8G DigitalMedia 8G J DM and DM 8G are trademarks or registered trademarks of Crestron Electronics Inc in the United States and other countries HDMI and the HDM
3. the chassis ground lug to earth ground building steel For details refer to the latest version of the DM TX 200 C 2G FLOOR DM TX 200 C 2G WALL www crestron com 888 273 7876 201 767 3400 a Operations and Installation Guide Doc 7255 ee ae eee eee KH c gt CS EST O es ere a GJ Fe Fe N QUICKSTART DOC 7256B 2032217 10 11 DM TX 200 C 2G FLOOQR WALL DM TX 200 C 2G WALL Installation DM TX 200 C 2G WALL Installation into Electrical Box 2 Gang Electrical Box Not Included The DM TX 200 C 2G WALL installs in a 2 gang electrical box not included in an insulated wall floor or ceiling A minimum mounting depth of 2 5 inches 64 mm DM TX 200 C 2G WALL is required 6505711 To install the DM TX 200 C 2G WALL in an electrical box quickstart guide 1 Using a Phillips head or straight blade screwdriver attach the DM TX 200 C 2G WALL to the electrical box using the four included 6 32 x 3 4 inch truss combo head screws 2009211 ia ania 2 Attach the included black faceplate 2032185 or the Head Screws 4 included white faceplate 2032202 to the front panel of PRIN the DM TX 200 C 2G WALL Front Panel Faceplate Black 2032185 or Front Panel Faceplate White 2032202 Both Included Front Panel Connections Front Panel Connections DM TX 200 C 2G FLOOR Shown O IP Address Setup DM TX 200 C 26 FLOOR Front Panel Setup of the IP address of
4. DM TX 200 C C 2G FLOOQR WALL Installation Overview PoDM Via Connection to DM Switcher DM TX 200 C 2G FLOOR and Installation DM MD8X8 Shown The DM TX 200 C 2G FLOOR is designed for installation DM TX 200 C 26 FLOOR Rear Panel Refer to Section below for information about installing the in a 6 inch 153 mm floor box not included or in an open ventilated area for example under a table The DM TX 200 C 2G WALL is designed for installation in a 2 gang electrical box not included in an insulated wall floor or ceiling DM TX 200 C 2G FLOOR in a floor box not included Refer to Section on the following page for information about installing the DM TX 200 C 2G WALL in an electrical box not included D DM TX 200 C 2G FLOOR Installation om mp8x8 The DM TX 200 C 2G FLOOR fits in a 2 gang opening in a 6 inch 4 153 mm floor box not included A minimum mounting depth of 2 5 inches 64 mm is required Rear Panel Connections Ground When installing the DM TX 200 C 2G FLOOR into a floor box not included or the DM TX 200 C 2G WALL into an electrical box not included verify that the required wiring has been fed through the floor box electrical box before connecting the rear panel of the device quickstart guide Using a Phillips head or straight blade screwdriver attach the DM TX 200 C 2G FLOOR to an installed floor box using the four included 6 32 x 3 4 inch truss combo head
5. I logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and or other countries Other trademarks registered trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Crestron disclaims any proprietary interest in the marks and names of others 2011 Crestron Electronics Inc For details refer to the latest version of the DM TX 200 C 2G FLOOR DM TX 200 C 2G WALL www crestron com l T Operations and Installation Guide Doc 7255 Specifications subject to A eines CQ CREST RON QUICKSTART DOC 7256B 2032217 10 11 iii
Download Pdf Manuals
Related Search