Home
H9A15 Cabinet Installation/Owner`s Guide
Contents
1. LJ 06400 AI7 H9A15 Cabinet Installation Owner s Guide 4 19 Installation 4 5 5 Removing and Replacing the Front Filler Panels The H9A15 cabinet can have metal or plastic front filler panels To remove a metal front filler panel refer to Figure 4 9 and proceed as follows Removal Grasp the metal front filler panel on both sides and then pull straight back away from the cabinet Replacement To replace a metal front filler panel align the sockets on the front filler panel refer to the exploded view with the appropriate ball studs on the rails and push the panel into place To remove a plastic front filler panel proceed as follows Removal Remove the four 10 32 screws that secure each corner of the front filler panel to the U nuts on the front rails and pull the front filler panel away from the cabinet Replacement To replace a plastic front filler panel align the holes at each corner of the front filler panel with the U nuts on the cabinet rails and secure the front filler panel with four 10 32 screws 4 20 9 15 Cabinet Installation Owner s Guide Installation Figure 4 9 Removing and Replacing the Metal Front Filler Panels isa EN S J LJ 06356 AI7 H9A15 Cabinet Installation Owner s Guide 4 21 Installation 4 5 6 Removing and Replacing
2. 2 4 Figure 2 2 Installing the eieae Enee 2 6 Figure 2 3 Deskidding the 2 6 Figure 2 4 Removing and Replacing Side Panels With External 2 11 Figure 2 5 Removing and Replacing Side Panels Without External Screws 2 13 Figure 2 6 Removing and Replacing the Front Door Strike 2 15 Figure 2 7 Removing and Replacing the Metal Front Filler 15 2 17 Figure 2 8 Pulling Out and Adjusting the Stabilizer 2 19 Figure 2 9 The Interlock Systeri secies 2 22 Figure 2 10 Removing a Power Distribution Unit eese 2 24 Figure 3 1 Standard Depth H9A15 NA TA WA Cabinet eee eene 3 3 Figure 3 2 H9A15 NA TA WA Cabinet with Extender 3 4 Figure 4 1 Unpacking the nnne 4 4 Figure 4 2 Installing the Ramps eeeeeeeeeeeeeeeenee nnne nennen nennen enne enne neret 4 6 Figure 4 3 Deskidding the Cabinet 4 8 Figure 4 4 Removing and Replacing the Rear Door cccssscceeeeeceeceeeeeeeceseeeeeseeeeeeenees
3. LJ 06396 A17 H9A15 Cabinet Installation Owner s Guide 4 23 Installation 4 5 7 Adjusting the Stabilizer Bars The stabilizer bars pull straight out from the bottom front of the cabinet as shown in Figure 4 11 When the stabilizer bars are fully extended adjust the feet at the end of the stabilizer bars until they touch the floor WARNING The stabilizer bars must be fully extended before any system is extended out of the cabinet on its slides The H9A15 cabinet can hold several system configurations The amount of force required to tip or make the cabinet unstable differs with each configuration 4 24 H9A15 Cabinet Installation Owner s Guide Installation Figure 4 11 Pulling Out and Adjusting the Stabilizer Bars H9A15 Cabinet Installation Owner s Guide 4 25 Installation 4 5 8 Using the Interlock System The interlock system refer to Figure 4 12 helps prevent cabinet instability by allowing only one system at any one time to be pulled out of the cabinet The interlock system consists of a vertical rod on which are mounted actuator latches for each product installed in the cabinet These actuator latches engage the interlock actuator bracket on the rear of rackmount systems When a rackmount system is pulled out of the cabinet the actuator latches rotate to prevent any other rackmounted system that has an interlock actuator bracket from being pulled out
4. from the shipping carton and set the ramps in the holes provided at the front of the pallet O Ensure that the arrows D on the ramps match the pallet arrows as shown in Figure 4 2 Caution In the next step the leveler feet must be fully retracted to prevent contact with the ramp or the floor when the cabinet is unloaded from the pallet Adjust the four cabinet leveler feet and the leveler feet on the stabilizer bars to the maximum upward position H9A15 Cabinet Installation Owner s Guide 4 5 Installation Figure 4 2 Installing the Ramps 4 6 H9A15 Cabinet Installation Owner s Guide 10 11 Installation WARNING In the following step use sufficient personnel to move the cabinet off the pallet Depending on the model ordered the cabinet weighs from 124 74 kg 275 Ib to 154 22 kg 340 Ib empty and can weigh from 578 34 kg 1 275 Ib up to 607 82 kg 1 340 Ib fully configured If equipment is installed in the cabinet the cabinet may become top heavy and could accelerate rapidly down the ramps if not restrained Be prepared to guide and control the motion of the cabinet Refer to Figure 4 3 and roll the cabinet down the ramps using sufficient personnel for safety Wheel the cabinet to the desired location Adjust the leveler feet downward so that the cabinet is level and the load is removed from the casters Caution Ensure that the leveler feet extend enough to carry the load of the
5. Caution In the next step the leveler feet must be fully retracted to prevent contact with the ramp or the floor when the cabinet is unloaded from the pallet Adjust the four cabinet leveler feet and the leveler feet on the stabilizer bars to the maximum upward position H9A15 Cabinet Installation Owner s Guide 2 5 Installation Figure 2 2 Installing the Ramps 2 6 H9A15 Cabinet Installation Owner s Guide 10 11 Installation WARNING In the following step use sufficient personnel to move the cabinet off the pallet Depending on the model ordered the cabinet weighs from 124 74 kg 275 Ib to 154 22 kg 340 Ib empty and can weigh from 578 34 kg 1 275 Ib up to 607 82 kg 1 340 Ib fully configured If equipment is installed in the cabinet the cabinet may become top heavy and could accelerate rapidly down the ramps if not restrained Be prepared to guide and control the motion of the cabinet Refer to Figure 2 3 and roll the cabinet down the ramps using sufficient personnel for safety Wheel the cabinet to the desired location Adjust the leveler feet downward so that the cabinet is level and the load is removed from the casters Caution Ensure that the leveler feet extend enough to carry the load of the cabinet so that the casters spin freely If not the stability of the cabinet may be compromised H9A15 Cabinet Installation Owner s Guide 2 7 Installation Figure 2 3 Deskidding t
6. cabinet so that the casters spin freely If not the stability of the cabinet may be compromised H9A15 Cabinet Installation Owner s Guide 4 7 Installation Figure 4 3 Deskidding the Cabinet LJ 06355 AI7 4 8 H9A15 Cabinet Installation Owner s Guide Installation 4 5 Installation Procedures During the installation of the cabinet one or more of the following procedures may be needed e Removing and Replacing the Rear Door Section 4 5 1 e Reversing the Rear Door Swing Section 4 5 2 e Removing and Replacing the Front Door Section 4 5 3 e Reversing the Front Door Swing Section 4 5 4 e Removing and Replacing the Front Filler Panels Section 4 5 5 e Removing and Replacing the Side Panels Section 4 5 6 e Adjusting the Stabilizer Bar Section 4 5 7 e Using the Interlock System Section 4 5 8 The tools needed to perform the above procedures are e Phillips screwdriver 8mm hex head nutdriver H9A15 Cabinet Installation Owner s Guide 4 9 Installation 4 5 1 Removing and Replacing the Rear Door The rear door provides access into the rear of the cabinet To remove the rear door refer to Figure 4 4 and proceed as follows Removal 1 Open the door and loosen the two 5 hex head screws that secure the top rear trim piece to the top of the cabinet 2 Slide the top rear trim piece toward the rear of the cabinet until the screw heads are aligned with the keyhole and lift the top
7. can have metal or plastic front filler panels To remove a metal front filler panel refer to Figure 2 7 and proceed as follows Removal Grasp the metal front filler panel on both sides and then pull straight back away from the cabinet Replacement To replace a metal front filler panel align the sockets the front filler panel refer to the exploded view with the appropriate ball studs on the rails and push the panel into place To remove a plastic front filler panel proceed as follows Removal Remove the four 10 32 screws that secure each corner of the front filler panel to the U nuts on the front rails and pull the front filler panel away from the cabinet Replacement To replace a plastic front filler panel align the holes at each corner of the front filler panel with the U nuts on the cabinet rails and secure the front filler panel with four 10 32 screws 2 16 9 15 Cabinet Installation Owner s Guide Installation Figure 2 7 Removing and Replacing the Metal Front Filler Panels isa EN S J LJ 04715 TIO H9A15 Cabinet Installation Owner s Guide 2 17 Installation 2 5 5 Adjusting the Stabilizer Bars The stabilizer bars pull straight out from the bottom front of the cabinet as shown in Figure 2 8 When the stabilizer bars are fully extended adjust the feet at the end of the stabilizer bars until they touch
8. door is square tighten the top pivot bracket mounting screws 4 14 9 15 Cabinet Installation Owner s Guide Installation Figure 4 6 Removing and Replacing the Front Door LJ 06398 AI7 H9A15 Cabinet Installation Owner s Guide 4 15 Installation 4 5 4 Reversing the Front Door Swing The front door on H9A15 cabinet comes from the factory hinged on the left side of the cabinet as viewed from the front of the cabinet The door swing can be reversed so that the front door is hinged on the right side of the cabinet as viewed from the front of the cabinet To reverse the rear door swing refer to Figure 4 7and Figure 4 8 and proceed as follows 1 10 11 12 13 Remove the front door see Section 4 5 3 and set it aside with the inside of the door facing outward Remove the rubber bumpers from top and bottom left corners of the door and move them to the top and bottom right corners of the door Remove the bottom pivot pin and plastic washer from the bottom pivot bracket located at the bottom left of the cabinet see Figure 4 6 Install the bottom pivot pin and washer in the bottom pivot bracket located at the bottom right of the cabinet see Figure 4 7 Remove the door alignment ramp from the bottom right of the cabinet and install it at the b
9. essen nennen nnne 2 20 2 5 7 Removing and Replacing a Power Distribution Unit eene 2 23 Part 1 H9A15 NA TA WA Cabinets 3 Introduction 3 I Description soit is Ss a sh As SEERE 3 1 SEPAN SIBICISI INR 3 5 4 Installation 4L Introduction 2 522 Ree oe ee e ed e e ebrei ie ar eie Seve o edes qd 4 1 4 2 Tools Required e ene Re eR RU Re S P ERR REX PERRA ERR ee 4 1 4 3 Site Planning ES 4 1 4A Unpackinbp c t A cds UP ORO QN E SEHEN EIS 4 3 4 5 Installation Procedures engeren er p HU raS e 4 9 4 5 1 Removing and Replacing the Rear Door eene 4 10 4 5 2 Reversing the Rear Door Swing eese nennen nennen nennen 4 12 4 5 3 Removing and Replacing the Front Door 4 14 4 5 4 Reversing the Front Door Swing eese eee nennen nene 4 16 4 5 5 Removing and Replacing the Front Filler Panels eenee 4 20 4 5 6 Removing and Replacing Side Panels eene 4 22 4 5 7 Adjusting the Stabilizer Bars cece eesceceseesseecsseeeeseeeesseecsaeeceeecsaeecseecesaeeesaeesas 4 24 4 5 8 Using the Interlock System 0 cece eeseessecsscecsseeceseececseecscecesaeeesaeecsaeesseessneeeesaes 4 26 Figures Figure 1 1 Standard Depth H9A15 Bx Rx Cabinets eene 1 3 Figure 1 2 Extended Depth H9A15 Cx Sx Cabinets eese 1 4 Figure 2 1 Unpacking the Cabinet
10. rear trim piece off of the cabinet 3 While holding the rear door in place remove the three M5 screws that secure the top pivot bracket to the top right of the cabinet and remove the bracket 4 Lift the rear door off of the bottom pivot pin located at the bottom right of the cabinet and place the rear door aside and out of the way Replacement To replace the rear door reverse the removal procedure steps 1 through 4 When replacing the rear door adjust the position of the top pivot bracket to ensure that the door is square with the cabinet opening Once the door is square tighten the top pivot bracket mounting screws 4 10 H9A15 Cabinet Installation Owner s Guide Installation Figure 4 4 Removing and Replacing the Rear Door LJ 06394 A17 H9A15 Cabinet Installation Owner s Guide 4 11 Installation 4 5 2 Reversing the Rear Door Swing The rear door on the H9A15 cabinet comes form the factory hinged on the right side of the cabinet as viewed from the rear of the cabinet The door swing can be reversed so that the rear door is hinged on the left side of the cabinet as viewed from the rear of the cabinet To reverse the rear door swing refer to Figure 4 5 and proceed as follows 1 2 10 11 12 13 Remove the rear door see Section 4 5 1 Remove the bottom pivot pin and plastic washer from the bottom pi
11. sufficient workspace for unpacking Ensure that there is sufficient clearance in front of the pallet marked with arrows to roll the cabinet down the ramps Refer to Figure 4 1 Cut and remove the plastic wrapping that secures the corner posts and the carton to the cabinet The carton contains the two ramps Remove the corner posts and the carton from the pallet Note In the next step take care not to damage the cabinet finish when removing the plastic bag Remove the plastic bag covering the cabinet Check the cabinet and the associated equipment for any external damage Report any damage to Compaq Customer Service or a Compaq sales office and to the responsible freight carrier Note Keep all packing material and receipts in case a damage claim is filed H9A15 Cabinet Installation Owner s Guide 4 3 Installation Figure 4 1 Unpacking the Cabinet JUI QN D ee LJ 06353 A17 4 4 9 15 Cabinet Installation Owner s Guide Installation Refer to Figure 4 2 Remove the four shipping bolts and brackets that secure the four cabinet leveler feet to the pallet Note The ramps attach to the front of the pallet Therefore the cabinet will have to be rolled frontwards down the ramps Remove the ramps
12. the floor WARNING The stabilizer bars must be fully extended before any system is extended out of the cabinet on its slides The H9A15 Cabinet can hold various system configurations The amount of force required to tip or make the cabinet unstable differs with each configuration 2 18 9 15 Cabinet Installation Owner s Guide Installation Figure 2 8 Pulling Out and Adjusting the Stabilizer Bars gt H9A15 Cabinet Installation Owner s Guide 2 19 Installation 2 5 6 Using the Interlock System The interlock system refer to Figure 2 9 helps prevent cabinet instability by allowing only one system at any one time to be pulled out of the cabinet The interlock system consists of a vertical rod on which are mounted actuator latches for each product installed in the cabinet These actuator latches engage the interlock actuator bracket on the rear of rackmount systems When a rackmount system is pulled out of the cabinet the actuator latches rotate to prevent any other rackmounted system that has an interlock actuator bracket from being pulled out of the cabinet The expanded view A shows the position of the actuator latches when all systems are pushed into the cabinet The expanded view B shows the position of all actuator latches after one system has been pulled out WARNING If additional products are installed into the cabinet actuator latches for those products should be installed to pr
13. 00 Ib 7 62 cm 3 in 225 kg 500 Ib Painted 100 to 120 Vac single phase 3 wire 200 to 240 Vac single phase 3 wire 200 to 240 Vac single phase 3 wire 24 A per H7600 AA PDU 16 A per H7600 AB DB PDU 47 to 63 Hz 2 88 kVA per H7600 AA PDU 3 84 kVA per H7600 AB DB PDU H7600 AA Two 2 120 Vac with L5 30P plugs H7600 AB Two 2 240 Vac with L6 20P plugs H7600 DB Two 2 240 Vac with IEC 309 plugs 2 Installation 2 1 Introduction This chapter provides the following information e Tools Required Section 2 2 e Site Planning Section 2 3 e Unpacking Section 2 4 e Installation Procedures Section 2 5 2 2 Tools Required The tools needed to install the H9A15 Bx Cx Rx Sx cabinet are e Utility knife e Phillips screwdriver e 9 16 open end wrench or adjustable wrench e mm nutdriver 2 3 Site Planning The cabinet requires a space of 60 0 cm 23 6 in by 109 95 cm 43 3 in maximum depending on the cabinet model In addition the cabinet requires a clearance of 91 44 cm 36 0 in at both the front and rear of the cabinet for service This may be greater depending on the distance that a system may be slid out of the cabinet H9A15 Cabinet Installation Owner s Guide 2 1 Installation WARNING High Leakage Current An insulated earthing conductor that is identical in size insulation material and thickness to the earthed and unearthed branch circuit supply conductors except th
14. 4 11 Figure 4 5 Reversing the Rear Door Swing eese nene 4 13 Figure 4 6 Removing and Replacing the Front 4 15 Figure 4 7 Reversing the Front Door Swing nennen nennen 4 18 Figure 4 8 Completing the Front Door eene 4 19 Figure 4 9 Removing and Replacing the Metal Front Filler Panels 4 21 Figure 4 10 Removing and Replacing the Side eere 4 23 Figure 4 11 Pulling Out and Adjusting the Stabilizer Bars eene 4 25 Figure 4 12 The Interlock System eese nennen nnne enne 4 28 Preface Overview This guide provides the information necessary to install the H9A15 cabinet This guide does not provide information concerning systems that can be installed in the cabinet For information concerning systems installed in the cabinet refer to the respective documentation shipped with the system Intended Audience The instructions in this guide are for Compaq Customer Service representatives and customer maintenance personnel who are familiar with computer hardware and operating systems Personnel should be experienced and trained in installing computer and related equipment How to Use This Guide Read the part of this guide that refers to your cabinet before installing the H9A15 cabinet As mentioned earlier for information concerning systems
15. H9A15 Cabinet Installatior Owners Guide Part Number EK H9A15 IN C01 May 1999 Compag Computer Corporation Houston Texas May 1999 COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING PERFORMANCE OR USE OF THIS MATERIAL THIS INFORMATION IS PROVIDED AS IS AND COMPAQ COMPUTER CORPORATION DISCLAIMS ANY WARRANTIES EXPRESS IMPLIED OR STATUTORY AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE GOOD TITLE AND AGAINST INFRINGEMENT This publication contains information protected by copyright No part of this publication may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation 1999 Compaq Computer Corporation All rights reserved The software described in this guide is furnished under a license agreement or nondisclosure agreement The software may be used or copied only in accordance with the terms of the agreement Compaq and the Compaq logo are registered in United States Patent and Trademark Office AlphaServer is a trademark of Compaq Computer Corporation Other product names mentioned herein may be trademarks and or registered trademarks of their respective companies Table of Contents Preface OVCEVIEW nee bue ee Re ee eed eee vii Intended Audience cccessecccscccsscesssc
16. This is a vertical rod at the rear of the cabinet that allows only one slide mounted device to be pulled out of the cabinet at any one time Note The equipment installed must have an interlock actuator bracket to work with the interlock system Two single phase H7600 AA 120 Vac or H7600 AB DB 240 Vac power distribution units PDUs Each H7600 AA AB power distribution unit provides ten 10 ac power outlets and each H7600 DB power distribution unit provides twelve 12 ac power outlets Two power cords Depending on the power distribution units shipped in the cabinet the two power cords from the power distribution units have either NEMA L5 30P plugs for 120 Vac H7600 AA operation L6 20P plugs for 240 Vac H7600 AB operation or IEC 309 plugs for 240 Vac H7600 DB operation If the plugs are not compatible to your power source receptacle contact your Compaq Customer Service office for assistance 1 2 H9A15 Cabinet Installation Owner s Guide Introduction Figure 1 1 Standard Depth H9A15 Bx Rx Cabinets A Standard depth cabinet with front Standard depth cabinet with front door trim kit kit H9A15 Cabinet Installation Owner s Guide 1 3 Introduction Figure 1 2 Extended Depth H9A15 Cx Sx Cabinets Extended depth cabinet with front O Extended dept
17. age Reader s Comments Compaq welcomes your comments on this or any other manual You can send your comments to Compaq in the following ways e Internet electronic mail reader comments digital com e Mail Compaq Computer Corporation Information Design PKO3 2 21J 129 Parker Street Maynard MA 01754 2199 For additional information call 1 800 282 6672 Part H9A15 Bx Cx Rx Sx Cabinets Part I of this manual provides an introduction and installation procedures for the H9A15 cabinets that are listed below Chapter 1 provides an introduction to these H9A15 cabinets and Chapter 2 provides the installation procedures Cabinet Description H9A15 BA BB BG Standard depth gray front trim kit hinged rear door H9A15 BC BD BH Standard depth gray hinged front door hinged rear door H9A15 CA CB CG Extended depth gray front trim kit hinged rear door H9A15 CC CD CH Extended depth gray hinged front door hinged rear door H9A15 RA RB RG Standard depth blue front trim kit hinged rear door H9A15 RC RD RH Standard depth blue hinged front door hinged rear door H9A15 SA SB SG Extended depth blue front trim kit hinged rear door H9A15 SC SD SH Extended depth blue hinged front door hinged rear door 1 Introduction 1 1 Description The H9A15 Bx Cx Rx Sx cabinets Figure 1 1 and Figure 1 2 are low cost computer equipment enclosure systems that meet the Electronic Industries Association EIA standard 310C and the Internat
18. at it is green with or without one or more yellow stripes is to be installed as part of the branch circuit that supplies the unit or system The earthing conductor described is to be connected to earth at the service equipment or if supplied by a separately derived system at the supply transformer or motor generator set The attachment plug receptacles in the vicinity of the unit or system are all to be of an earthing type and the earthing conductors serving these receptacles are to be connected to earth at the service equipment WARNING Use sufficient personnel when unloading the cabinet from the pallet or moving the cabinet to a new location Depending on the model ordered the cabinet weighs from 124 74 kg 275 Ib to 154 22 kg 340 Ib empty and can weigh from 578 34 kg 1 275 Ib up to 607 82 kg 1 340 Ib fully configured For site preparation details concerning the system devices installed or the systems to be installed in the cabinet refer to the documentation for those systems 2 2 H9A15 Cabinet Installation Owner s Guide Installation 2 4 Unpacking The cabinet is shipped on a wooden pallet Proceed as follows to unpack the cabinet 1 Position the pallet with the cabinet in an area that provides sufficient workspace for unpacking Ensure that there is sufficient clearance in front of the pallet marked with arrows to roll the cabinet down the ramps Refer to Figure 2 1 Cut and remove the plastic wrapping that secu
19. e 3 1 and Figure 3 2 are low cost computer equipment enclosure systems that meet the Electronic Industries Association EIA standard 310C and the International Electrotechnical Commission IEC 297 standards and can accommodate fixed or slide mounted chassis that fit into a standard 48 26 cm 19 in rack Depending on the options ordered the cabinet may have the following features Equipment mounting rails with the universal rail hole pattern Front trim kit that provides a finished look to the front opening of the cabinet or a front door kit Both versions of the standard depth cabinet are shown in Figure 3 1 and both versions of the cabinet with the extender kit are shown in Figure 3 2 Front and rear doors with key locks A door and collar assembly that extends the front of the cabinet 6 35 cm 2 5 in Factory installed only A collar assembly that extends the rear of the cabinet 18 75 cm 7 38 in Factory installed only Other cabinet features include the following Vented top This aids in the ventilation of the system Hinged vented rear door This provides additional ventilation and controlled access to the rear of the cabinet Four nonlocking casters These facilitate the placement of the cabinet The front two casters swivel The rear two casters are fixed H9A15 Cabinet Installation Owner s Guide 3 1 Introduction e Adjustable leveling feet These are used to stabilize and secure the cabinet a
20. e and the lock properly engages the strike plate Reinstall the top rear trim piece on the top rear of the cabinet Reverse the handle on the door latch by unscrewing the lock and turning the handle upside down so that the handle is toward the bottom of the door 4 12 9 15 Cabinet Installation Owner s Guide Installation Figure 4 5 Reversing the Rear Door Swing LJ 06395 AI7 H9A15 Cabinet Installation Owner s Guide 4 13 Installation 4 5 3 Removing and Replacing the Front Door The front door provides access into the front of the cabinet To remove the front door refer to Figure 4 6 and proceed as follows Removal 1 Open the door and loosen the two 5 hex head screws that secure the top front trim piece to the top of the cabinet 2 Slide the top front trim piece up and off of the cabinet 3 While holding the front door in place remove the two MS screws that secure the top pivot bracket to the top left of the cabinet and remove the bracket 4 Lift the front door off of the bottom pivot pin located at the bottom left of the cabinet and place the front door aside and out of the way Replacement To replace the front door reverse steps 1 through 4 of the removal procedure When replacing the front door adjust the position of the top pivot bracket to ensure that the door is square with the cabinet opening Once the
21. e power cords from that power distribution unit 7 At the rear of the cabinet remove the four 4 10 32 truss head screws that secure the power distribution unit to the rear rails via the four 4 10 32 clip nuts O 8 Pull out the power distribution unit and remove it from the cabinet Replacement To replace a power distribution unit reverse the removal procedure steps 2 through 8 then follow the power on procedure in the system documentation H9A15 Cabinet Installation Owner s Guide 2 23 Installation Figure 2 10 Removing a Power Distribution Unit o LJ 04288 TIO 2 24 H9A15 Cabinet Installation Owner s Guide Part Il H9A15 NA TA WA Cabinets Part II of this manual provides an introduction and installation procedures for the H9A15 cabinet models that are listed below Chapter 3 provides an introduction to these H9A15 cabinets and Chapter 4 provides the installation procedures Cabinet Description H9A15 NA Gray standard depth base cabinet H9A15 TA Blue standard depth base cabinet H9A15 WA White standard depth base cabinet One of the front dress treatment kits listed below is required for the base cabinet Front Dress Kit Description H9C15 NF Gray front door kit H9C15 NT Gray front trim kit H9C15 TF Blue front door kit H9C15 TT Blue front trim kit H9C15 WF White front door kit H9C15 WT White front trim kit 3 Introduction 3 1 Description The H9A15 NA TA WA cabinet Figur
22. ecscccsscessscccssccsssssuscecceccssseesscsesscssusecesssessuceucoessscesssenees vii How to Use This Guide eese eene nnne hen ennn nr rhn niis nn aane se sse vii Organization etn n gH ee epee DER SERE Uer PEE nde viii Conventlollsc Mns ee els cote tend heat oo Mle once cie Qu viii Safety Seavert ei eie rele eee viii Readers Comments eoo eter OA NE erret e EIE ix Part H9A15 Bx Cx Rx Sx Cabinets 1 Introduction 1 1 Description ri ee et ere ede ete dee tide ei iet e eee dn 1 1 1 2 Specifications o edes Heise ete te te t tte aite cete a e Let tuns 1 5 2 Installation 2 Introduction 2 1 2 2 Tools Requited o pee PRI IRIURE ERI eR INR 2 1 2 3 Site PIantng e REB PPAR AR He PR dr HERE ERI deg 2 1 2 4 Unpacking ts oia SE REOR HE CEP editt 2 3 2 5 Installation PtocedUures opto e oU np tdem 2 9 2 5 1 Removing and Replacing Side Panels With External 2 10 2 5 2 Removing and Replacing Side Panels Without External Screws 2 12 2 5 3 Removing and Replacing the Front Door Strike Plate eee 2 14 2 5 4 Removing and Replacing the Front Filler eene 2 16 2 5 5 Adjusting the Stabilizer Bars ener nene 2 18 2 5 6 Using the Interlock System
23. f the cabinet 2 12 H9A15 Cabinet Installation Owner s Guide Installation Figure 2 5 Removing and Replacing Side Panels Without External Screws LJ 06397 AI7 H9A15 Cabinet Installation Owner s Guide 2 13 Installation 2 5 3 Removing and Replacing the Front Door Strike Plate To remove the front door strike plate refer to Figure 2 6 and proceed as follows Removal Remove either the two 8 32 screws and two 8 32 kepnuts or the two M5 machine screws that secure the front door strike plate to the front collar Replacement To replace the front door strike plate align the two holes on the front door strike plate with the two holes on the cabinet frame and secure it in place with either the two 8 32 screws and two 8 32 kepnuts or two M5 machine screws Note The front door strike plate prevents the left side access door on an AlphaServer 2100 RM series system when installed in the door latch area of the H9A15 cabinet from being fully opened and must be removed to allow access 2 14 H9A15 Cabinet Installation Owner s Guide Installation Figure 2 6 Removing and Replacing the Front Door Strike Plate LJ 04714 TIO H9A15 Cabinet Installation Owner s Guide 2 15 Installation 2 5 4 Removing and Replacing the Front Filler Panels The H9A15 cabinet
24. h cabinet with front door trim kit kit 1 4 H9A15 Cabinet Installation Owner s Guide Introduction 1 2 Specifications Specifications for the H9A15 Cabinet are as follows Physical Height overall 200 cm 78 7 in Width overall 60 0 cm 23 6 in Depth overall 84 89 cm 33 42 in Standard depth with front trim kit 91 24 cm 35 92 in Standard depth with front door kit 103 6 cm 40 8 in Extended depth with front trim kit 109 95 cm 43 3 in Extended depth with front door kit Maximum vertical rackmounting space 182 3 cm 71 75 in Maximum vertical rackmounting space with 173 4 cm 68 25 in power distribution units installed Horizontal rack width Standard 48 26 cm 19 in Weight Standard depth cabinet with front trim kit and 124 74 kg 275 16 two power distribution units Standard depth cabinet with front trim kit and 150 14 kg 331 Ib two power distribution units plus packing material Fully configured filled standard depth Up to 578 34 kg 1 275 1b cabinet with front trim kit Fully configured filled standard depth Up to 603 74 kg 1 331 1b cabinet with front trim kit plus packing material Standard depth cabinet with front door kit and 141 98 kg 313 Ib two power distribution units Standard depth cabinet with front door kit and 167 38 kg 369 Ib two power distribution units plus packing material Fully configured filled standard depth Up to 595 58 kg 1 313 Ib cabinet with front door kit Fully conf
25. he Cabinet 2 8 H9A15 Cabinet Installation Owner s Guide Installation 2 5 Installation Procedures During the installation of the cabinet one or more of the following procedures may be needed Removing and Replacing Side Panels With External Screws Section 2 5 1 Removing and Replacing Side Panels Without External Screws Section 2 5 2 Removing and Replacing the Front Door Strike Plate Section 2 5 3 Removing and Replacing the Front Filler Panels Section 2 5 4 Adjusting the Stabilizer Bars Section 2 5 5 Using the Interlock System Section 2 5 6 Removing and Replacing a Power Distribution Unit Section 2 5 7 H9A15 Cabinet Installation Owner s Guide 2 9 Installation 2 5 1 Removing and Replacing Side Panels With External Screws The side panels on the H9A15 cabinets are removable Some of the H9A15 cabinets have side panels that are secured with external screws Note If the side panels are removed replace them before powering up any equipment To remove the side panels with external screws refer to Figure 2 4 and proceed as follows Removal 1 Remove the six M5 Phillips head machine screws securing the side panel to the cabinet frame 2 Grasp both sides of the side panel and lift the side panel away from the cabinet frame 3 Place the side panel aside and out of the way Replacement To replace the side panel reverse the removal procedure steps 1 through 3 2 10 H9A15 Cabinet Instal
26. he following information e Tools Required Section 4 2 e Site Planning Section 4 3 e Unpacking Section 4 4 e Installation Procedures Section 4 5 4 2 Tools Required The tools needed to install the H9A15 NA TA WA cabinet are e Utility knife e Phillips screwdriver e 9 16 open end wrench or adjustable wrench e mm nutdriver 4 3 Site Planning The cabinet requires a space of 60 0 cm 23 6 in by 91 6 cm 36 1 in maximum depending on the cabinet model In addition the cabinet requires a clearance of 91 44 cm 36 0 in at both the front and rear of the cabinet for service This may be greater depending on the distance that a system may be slid out of the cabinet H9A15 Cabinet Installation Owner s Guide 4 1 Installation WARNING Use sufficient personnel when unloading the cabinet from the pallet or moving the cabinet to a new location Depending on the model ordered the cabinet weighs from 124 74 kg 275 Ib to 154 22 kg 340 Ib empty and can weigh from 578 34 kg 1 275 Ib up to 607 82 kg 1 340 Ib fully configured For site preparation details concerning the system devices installed or the systems to be installed in the cabinet refer to the documentation for those systems 4 2 H9A15 Cabinet Installation Owner s Guide Installation 4 4 Unpacking The cabinet is shipped on a wooden pallet Proceed as follows to unpack the cabinet 1 Position the pallet with the cabinet in an area that provides
27. he inside of the front door secure the latch and lock assembly panel to the right front of the door using four M5 nuts see Figure 4 8 Note If a lock guard was installed over the latch and lock assembly panel it must also be secured by these four M5 nuts While facing the inside of the front door secure the blank panel to the left front of the door using four M5 nuts Set the front door on the bottom pivot pin located at the bottom right of the cabinet Insert the top pivot pin on the top pivot bracket 9 into the hole at the top right corner of the door and while holding the door in place adjust the position of the top pivot bracket to ensure that the door is square with the cabinet opening Once the door is square secure the top pivot bracket to the top right of the cabinet by tightening the two MS screws 4 Adjust the strike plate so that the door does not rattle and the lock properly engages the strike plate Reinstall the top front trim piece on the top front of the cabinet and tighten the two MS hex head screws see Figure 4 8 H9A15 Cabinet Installation Owner s Guide 4 17 Installation Figure 4 7 Reversing the Front Door Swing LJ 06399 A17 4 18 9 15 Cabinet Installation Owner s Guide Installation Figure 4 8 Completing the Front Door Reversal
28. igured filled standard depth Up to 620 98 kg 1 369 Ib cabinet with front door kit plus packing material Extended depth cabinet with front trim kit and 137 kg 302 Ib two power distribution units H9A15 Cabinet Installation Owner s Guide 1 5 Introduction Extended depth cabinet with front trim kit and two power distribution units plus packing material Fully configured filled extended depth cabinet with front trim kit Fully configured filled extended depth cabinet with front trim kit plus packing material Extended depth cabinet with front door kit and two power distribution units Extended depth cabinet with front door kit and two power distribution units plus packing material Fully configured filled extended depth cabinet with front door kit Fully configured filled extended depth cabinet with front door kit plus packing material Casters swivel nonlocking Diameter Maximum capacity Casters fixed nonlocking Diameter Maximum capacity Enclosure finish Electrical AC input voltage for H7600 AA PDU AC input voltage for H7600 AB PDU AC input voltage for H7600 DB PDU AC load Input line frequency range Input power at full load Power cords 1 6 H9A15 Cabinet Installation Owner s Guide 162 39 kg 358 Ib Up to 590 59 kg 1 302 Ib Up to 616 kg 1 358 Ib 154 22 kg 340 Ib 179 63 kg 396 Ib Up to 607 82 kg 1 340 Ib Up to 633 23 kg 1 396 Ib 7 62 cm 3 in 225 kg 5
29. installed in the cabinet refer to the respective documentation shipped with the system Before installation review the warranty The terms of the warranty agreement with Compaq may require that a qualified Compaq Customer Service representative install the system Contact your local Compaq representative if you have any questions vii Organization This guide is organized as follows Part I Chapter 1 Introduction Provides an overview of the H9A15 Bx Cx Rx Sx cabinet features and specifications Chapter 2 Installation Provides site preparation unpacking and installation information for the H9A15 Bx Cx Rx Sx cabinet Part II Chapter 3 Introduction Provides an overview of the H9A15 NA TA WA cabinet features and specifications Chapter 4 Installation Provides site preparation unpacking and installation information for H9A15 NA TA WA cabinet Conventions The following conventions are used in this guide Convention Meaning Note A note calls the reader s attention to important information Caution Cautions provide information to prevent damage to equipment or software Read these carefully WARNING A warning contains information essential to the safety of personnel Safety Symbol viii The following symbol appears on the power distribution unit Please review its definition below This Dangerous Voltage warning symbol indicates a risk of electric shock and indicates hazards from dangerous volt
30. ional Electrotechnical Commission IEC 297 standards and can accommodate fixed or slide mounted chassis that fit into a standard 48 26 cm 19 in rack Depending on the model ordered the cabinet may have the following factory installed features Equipment mounting rails with the EIA universal rail hole pattern Front trim kit that provides a finished look to the front opening of the cabinet or a front door kit that extends the front of the cabinet out 6 35 cm 2 5 in for equipment clearance and front door support Both versions of the standard depth cabinet are shown in Figure 1 1 and both versions of the extended depth cabinet are shown in Figure 1 2 Front and rear doors with key locks A collar assembly that extends the rear of the cabinet 18 75 cm 7 38 in Other cabinet features include the following Vented top This aids in the ventilation of the system Hinged vented rear door This provides additional ventilation and controlled access to the rear of the cabinet Four nonlocking casters These facilitate the placement of the cabinet The front two casters swivel The rear two casters are fixed Adjustable leveling feet These are used to stabilize and secure the cabinet at the installation site H9A15 Cabinet Installation Owner s Guide 1 1 Introduction Stabilizer bars These are used to provide cabinet stability when installing or sliding equipment out of the cabinet Equipment interlock kit
31. lation Owner s Guide Installation Figure 2 4 Removing and Replacing Side Panels With External Screws H9A15 Cabinet Installation Owner s Guide 2 11 Installation 2 5 2 Removing and Replacing Side Panels Without External Screws The side panels on the H9A15 cabinets are removable Some of the H9A15 cabinets have side panels that are secured without external screws Note If the side panels are removed replace them before powering up any equipment To remove the side panels without external screws refer to Figure 2 5 and proceed as follows Removal 1 Gain access to the inside of the cabinet by opening the hinged rear door and front door if the cabinet has one 2 Remove the two M5 hex head screws that secure the side panel metal tabs to the mounting rail inside the cabinet one toward the front and one toward the rear of the cabinet 3 Grasp both sides of the side panel and lift it up until the side panel metal tabs clear the cutouts in the cabinet wall and the top lip of the side panel clears the angle bracket O along the top edge of the cabinet 4 Pullthe side panel out and away from the cabinet and set it aside Replacement To replace the side panel reverse the removal procedure steps 1 through 4 Ensure that the side panel metal tabs catch on the mounting rail at the bottom of the cutouts in the cabinet wall and the top lip of the side panel catches the angle bracket along the top edge o
32. of the cabinet The expanded view A shows the position of the actuator latches when all systems are pushed into the cabinet The expanded view B shows the position of all actuator latches after one system has been pulled out If additional products are installed into the cabinet actuator latches for those products should be installed To install actuator latches proceed as follows 1 Remove the screws securing the bottom mounting bracket to the cabinet Slide the mounting bracket off the bottom of the vertical rod Slide the stabilizer bracket for the new product onto the bottom of the vertical rod Slide the actuator latch for the new product onto the bottom of the vertical rod CAS wx 0 Replace the bottom mounting bracket and install the screws removed in step 1 but do not tighten them 6 Position the stabilizer bracket so that the bottom hole in the stabilizer bracket aligns with the EIA rail hole adjacent to the bottom of the installed product This may require the loosening and sliding of other latches and stabilizer brackets to accommodate the new configuration 7 Place the nut plate behind the EIA rail and install and tighten the screws provided to secure the stabilizer bracket 8 Position the new actuator latch to properly engage the product and tighten the set screws to secure the latch 9 Now tighten the screws to secure the bottom mounting bracket O 4 26 H9A15 Cabinet Installation O
33. ottom left of the cabinet Remove the two M5 screws that secure the strike plate to the right side of the cabinet Install the strike plate on the left side of the cabinet using the two M5 screws Remove the top pivot pin from the left front hole on the top pivot bracket see Figure 4 6 and install the pivot pin into the right front hole on the top pivot bracket see Figure 4 8 While facing the inside of the front door remove the four M5 nuts that secure the blank panel to the right front of the door and remove the blank panel see Figure 4 7 While facing the inside of the front door remove the four M5 nuts that secure the latch and lock assembly panel O to the left front of the door and remove the latch and lock assembly panel see Figure 4 7 Note Some cabinets may have a lock guard over the latch and lock assembly panel that is also secured by the four M5 nuts Remove the nut that secures the lock mechanism to the top part of the latch and lock assembly panel Move the lock mechanism to the bottom part of the latch and lock assembly panel and secure it with the nut removed in step 11 Turn the latch and lock assembly panel upside down so that the latch is toward the right side of the door as viewed from facing the inside of the front door and the lock mechanism is at the top 4 16 H9A15 Cabinet Installation Owner s Guide 14 15 16 17 18 19 Installation While facing t
34. ovide a stable environment To install actuator latches proceed as follows 1 Remove and save the screws securing the bottom mounting bracket to the cabinet O 2 Slide the mounting bracket off the bottom of the vertical rod 3 Slide the stabilizer bracket and the actuator latch for the new product onto the bottom of the vertical rod in the proper order Refer to the new product installation documentation for the proper order of the stabilizer bracket and actuator latch 4 Replace the bottom mounting bracket and install the screws removed in step 1 but do not tighten them 5 Position the stabilizer bracket so that the bottom hole in the stabilizer bracket aligns with the EIA rail hole adjacent to the bottom of the installed product This may require the loosening and sliding of other latches and stabilizer brackets to accommodate the new configuration 6 Place the nut plate behind the EIA rail and install and tighten the screws provided to secure the stabilizer bracket 7 Position the new actuator latch to properly engage the product and tighten the set screws to secure the latch 8 Now tighten the screws to secure the bottom mounting bracket O 2 20 H9A15 Cabinet Installation Owner s Guide Installation Note Some systems may not be compatible because the interlock actuator bracket may not engage properly In these cases do not install the interlock actuator bracket on those systems WARNING If a system i
35. res the corner posts and the carton 9 to the cabinet The carton contains the two ramps Remove the corner posts and the carton from the pallet Note In the next step take care not to damage the cabinet finish when removing the plastic bag Remove the plastic bag covering the cabinet Check the cabinet and the associated equipment for any external damage Report any damage to Compaq Customer Service or a Compaq sales office and to the responsible freight carrier Note Keep all packing material and receipts in case a damage claim is filed H9A15 Cabinet Installation Owner s Guide 2 3 Installation Figure 2 1 Unpacking the Cabinet WW iJ m JO Wi JUI e LJ 04710 TIO 2 4 H9A15 Cabinet Installation Owner s Guide Installation Refer to Figure 2 2 Remove the four shipping bolts and brackets that secure the four cabinet leveler feet to the pallet Note The ramps attach to the front of the pallet Therefore the cabinet will have to be rolled frontwards down the ramps Remove the ramps from the shipping carton and set the ramps in the holes provided at the front of the pallet O Ensure that the arrows D on the ramps match the pallet arrows as shown in Figure 2 2
36. s installed without an interlock actuator bracket or the vertical rod in the cabinet does not engage properly with the system interlock actuator bracket it is the customer s responsibility to provide a stable cabinet H9A15 Cabinet Installation Owner s Guide 2 21 Installation Figure 2 9 The Interlock System LJ 04717 TIO 2 22 H9A15 Cabinet Installation Owner s Guide Installation 2 5 7 Removing and Replacing a Power Distribution Unit WARNING There can be two or more PDUs per cabinet Ensure that all systems installed in the cabinet are turned off as described in the system documentation before performing the following procedure To remove a power distribution unit refer to Figure 2 10 and proceed as follows Removal 1 If the cabinet contains an operating system turn off the system as described in the system documentation 2 Open the rear door 3 Set the Main Power switch on all power distribution units to the off O position 4 Disconnect the power distribution units from the ac power source 5 If required remove the bottom front filler panel refer to Section 2 5 4 This provides access to the ac outlets on the power distribution units 6 Note and record the power cord connections to the outlets at the rear of the power distribution unit being removed Then unplug th
37. t the installation site e Stabilizer bars These are used to provide cabinet stability when installing or sliding equipment out of the cabinet e Equipment interlock kit This is a vertical rod at the rear of the cabinet that allows only one slide mounted device to be pulled out of the cabinet at any one time Note The equipment installed must have an interlock actuator bracket to work with the interlock system 3 2 H9A15 Cabinet Installation Owner s Guide Introduction Figure 3 1 Standard Depth H9A15 NA TA WA Cabinet Standard depth cabinet with Standard depth cabinet with optional optional front trim kit fi kit and optional front and rear extender kit H9A15 Cabinet Installation Owner s Guide 3 3 Introduction Figure 3 2 H9A15 NA TA WA Cabinet with Extender Kit Cabinet with optional extender kit O Cabinet with optional extender kit and and optional front trim kit optional front door kit 3 4 H9A15 Cabinet Installation Owner s Guide 3 2 Specifications Introduction Specifications for the H9A15 NA TA WA cabinet are as follows Physical Height overall Width overall Depth overall Maximum vertical rackmounting space Maximum vertical rackmounting space with power distribution units installed Horizontal rack width Weight F
38. the Side Panels 4 22 The H9A15 cabinet has removable side panels that can be swapped from one side of the cabinet to the other To remove a side panel refer to Figure 4 10 and proceed as follows Removal 1 Gain access to the inside of the cabinet by opening the rear door and the front door if the cabinet has one 2 If the cabinet has a front trim kit or a non extended front door kit remove the two Phillips head screws that secure bottom front trim cover 3 Remove the two M5 screws that secure the bottom front and rear corners of the side panel to the cabinet These screws are located underneath the metal lip that is parallel to the floor at the bottom front and bottom rear of the cabinet 4 Grasp both sides of the side panel and lift it up until the side panel metal tabs clear the cutouts in the cabinet wall and the top lip of the side panel clears the angle bracket along the top edge of the cabinet 5 Pullthe side panel out and away from the cabinet and set it aside Replacement To replace the side panel reverse the removal procedure steps 1 through 5 Ensure that the side panel metal tabs catch on the mounting rail at the bottom of the cutouts in the cabinet wall and the top lip of the side panel catches the angle bracket along the top edge of the cabinet H9A15 Cabinet Installation Owner s Guide Installation Figure 4 10 Removing and Replacing the Side Panels
39. ully configured filled standard depth cabinet with front trim kit Fully configured filled standard depth cabinet with front trim kit plus packing material Fully configured filled standard depth cabinet with front door kit Fully configured filled standard depth cabinet with front door kit plus packing material Fully configured filled cabinet with extender kit and front trim kit Fully configured filled cabinet with extender kit and front trim kit plus packing material Fully configured filled cabinet with extender kit and front door kit Fully configured filled cabinet with extender kit and front door kit plus packing material Casters swivel nonlocking Diameter Maximum capacity Casters fixed nonlocking Diameter Maximum capacity Enclosure finish 200 cm 78 7 in 60 0 cm 23 6 in 91 6 cm 36 1 in Standard depth with front trim kit or front door kit 97 9 cm 38 6 in Extender kit with front door kit 182 3 cm 71 75 in 41U 173 4 cm 68 25 in 39U Standard 48 26 cm 19 in Up to 578 34 kg 1 275 1b Up to 603 74 kg 1 331 Ib Up to 595 58 kg 1 313 Ib Up to 620 98 kg 1 369 Ib Up to 590 59 kg 1 302 Ib Up to 616 kg 1 358 Ib Up to 607 82 kg 1 340 Ib Up to 633 23 kg 1 396 Ib 7 62 cm 3 in 318 kg 700 Ib 7 62 cm 3 in 318 kg 700 Ib Painted H9A15 Cabinet Installation Owner s Guide 3 5 4 Installation 4 1 Introduction This chapter provides t
40. vot bracket located at the bottom right of the cabinet see Figure 4 4 Install the bottom pivot pin and washer 6 in the bottom pivot bracket located at the bottom left of the cabinet see Figure 4 5 Remove the wear pad see Figure 4 5 from the rear hole of the bottom pivot bracket located at the bottom left of the cabinet and move it to the rear hole of the bottom pivot bracket located at the bottom right of the cabinet Remove the two M5 screws that secure the strike plate to the left side of the cabinet Install the strike plate on the right side of the cabinet using the two M5 screws Ensure that the lip on the strike plate is pointing to the left Remove the top pivot pin from the right front hole on the top pivot bracket see Figure 4 4 and install the pivot pin into the left front hole on the top pivot bracket see Figure 4 5 Turn the rear door upside down so that the locking mechanism is on the right Set the rear door on the bottom pivot pin located at the bottom left of the cabinet Insert the top pivot pin on the top pivot bracket into the hole at the top left corner of the door and while holding the door in place adjust the position of the top pivot bracket to ensure that the door is square with the cabinet opening Once the door is square secure the top pivot bracket to the top left of the cabinet by tightening the three MS screws b Adjust the strike plate so that the door does not rattl
41. wner s Guide Installation Note Some systems may not be compatible because the interlock actuator bracket may not engage properly In these cases do not install the interlock actuator bracket on those systems WARNING If a system is installed without an interlock actuator bracket or the vertical rod in the cabinet does not engage properly with the system interlock actuator bracket it is the customer s responsibility to provide a stable cabinet H9A15 Cabinet Installation Owner s Guide 4 27 Installation Figure 4 12 The Interlock System LJ 06358 AI7 4 28 9 15 Cabinet Installation Owner s Guide
Download Pdf Manuals
Related Search
Related Contents
一括ダウンロード optimización de periféricos de entrada en el manejo de programas ASUS D550MA R8619 User's Manual Betriebsanleitung Plattformwaage Dell Inspiron 09N1F7A01 User's Manual Kawasaki R8126 User's Manual Barco R59770057 Projector User Manual Copyright © All rights reserved.
Failed to retrieve file