Compaq 7+ 1300 Tablet and Compaq 7 1200 Tablet
Contents
1. HP Business Notebook PC products that use Intel based or AMD based system boards contain volatile DDR memory The amount of nonvolatile memory present in the system depends upon the system configuration Intel based and AMD based system boards contain nonvolatile memory subcomponents as originally shipped from HP assuming that no subsequent modifications have been made to the system and assuming that no applications features or functionality have been added to or installed on the system Following system shutdown and removal of all power sources from an HP Business Notebook PC system personal data can remain on volatile system memory DIMMs for a finite period of time and will also remain in nonvolatile memory The steps below will remove personal data from the notebook PC including the nonvolatile memory found in Intel based and AMD based system boards Some of these steps are disclosed in the Maintenance and Service Guides available for HP PC products available on the product support pages at www hp com 1 Follow steps a through I below to restore the nonvolatile memory that can contain personal data Restoring or re programming nonvolatile memory that does not store personal data is neither necessary nor recommended d Enter BIOS F10 Setup by powering on the system and pressing F10 when prompted near the bottom of the display or press the ESC key to display the start up menu then press F10 If the system has a BIOS administrator2. Before removing the rearfacing webcamera follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 18 Chapter 5 Removal and replacement procedures 4 Remove the back cover see Back cover on page 13 5 Disconnect the battery cables from the system board see Battery on page 15 Remove the rearfacing webcamera 1 Turn the system board upside down 2 Release the zero insertion force ZIF connector 1 to which the rearfacing webcamera is attached and then disconnect the rear facing webcamera from the system board 3 Remove the rear facing webcamera 2 and cable Reverse this procedure to install the rearfacing webcamera e Microphone Description Spare part number Microphone includes cable 754529 001 Before removing the microphone follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 13 M o Mw Disconnect the battery cables from the syst
3. Engine Engine Code programmed at enforce Firmware Settings the factory hardware present only in models ending in a p or w or with Intel Centrino Pro technology Provisioning Data and iAMT third party data store Code is updated via Intel secure firmware update utility Unique Provisioning Data can be entered at the factory or by an administrator using the Management Engine MEBx setup utility The third party data store contents can populated by a remote management console or local applications registered by an administrator to have access to the space protection to block all direct read write access to this area An Intel utility is required for updating the firmware Only firmware updates digitally signed by Intel can be applied using this utility Non volatile memory usage 29 Non Volatile Amount Does this Does this What is the How is data How is this Memory Size memory memory purpose of input into memory Type store retain data this this write customer when power memory memory protected data is removed Bluetooth flash 2 MBits No Yes Stores Bluetooth Programmed at A utility is configuration the factory required for and firmware Tools for writing writing data to data to this this memory memory are not and is made publicly available available but through newer can be versions of the obtained from driver if the the silicon flash requires vendor an upgra
4. 4 Remove the antenna transceiver and cable Reverse this procedure to install the antenna Speaker Description Spare part number Speaker Kit includes speaker and cables 755197 001 Before removing the bottom speaker vibrator module assembly follow these steps _ Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 13 au B OQ N Disconnect the battery cables from the system board see Battery on page 15 Speaker 17 Remove the speaker 1 Unsolder the speaker cables 1 from the system board terminals f NOTE When installing the speaker the speaker red cable should be soldered to the system board terminal and the speaker black cable should be soldered to the terminal 2 Release the speaker cable 2 from the retention clip built into the display panel assembly 3 Detach the speaker 3 from the display panel assembly The speaker is attached to the display panel assembly with double sided adhesive 4 Remove the speaker Reverse this procedure to install the speaker Rear facing webcamera Description Spare part number 2 0 MP rearfacing webcamera includes cable 753193 001
5. as size serial number data width speed timing voltage and thermal information This information is written by the module manufacturer and stored on an EEPROM This EEPROM cannot be written to when the memory module is installed in a PC Third party tools do exist that can write to the EEPROM when the memory module is not installed in a PC There are various third party tools available to read SPD memory Does the Firmware Hub for System BIOS contain the BIOS program Is this chip writable and if so how The Firmware Hub does contain the BIOS program and is writable A utility is required to perform the write function In some PC systems the Firmware Hub for System BIOS is a flash memory chip so that updates can be written by the customer Is this true for these BIOS chips Yes they are flash memory chips What is meant by Restore the nonvolatile memory found in Intel based system boards This relates to clearing the Real Time Clock RTC CMOS memory that contains PC configuration data Does resetting the CMOS configuration memory return the PC back to factory defaults The process of resetting the CMOS will return certain system settings to factory default but will not reset many of the system data and configuration defaults to their default settings To return these system data and configuration defaults to default settings refer to question and answer 1 and follow the instructions for returning the BIOS settings to factory
6. password enter the password at the prompt b Select the File menu then Restore Defaults Select the System Configuration menu then Restore Security Defaults d If an asset or ownership tag is set select the Security menu and scroll down to the Utilities menu Select System IDs and then select the tag that has been set Press the spacebar once to clear the tag then press Enter to return to the prior menu e f a Drivelock password is set select the Security menu scroll down to DriveLock then select DriveLock password Select the desired hard drive Click Disable protection enter the existing master Drivelock password then press Enter to confirm and return to the prior menu Repeat this procedure if more than one hard drive has a Drivelock password Chapter 7 Statement of Volatility If an Automatic Drivelock password is set select the Security menu scroll down to Automatic DriveLock then select the desired hard drive and disable protection Repeat this procedure if more than one hard drive has an Automatic Drivelock password Select the File menu then Reset BIOS Security to factory default Click yes at the warning message Select the File menu then Save Changes and Exit Reboot the system If the system has a Trusted Platform Module and or fingerprint sensor one or two prompts will appear one to clear the TPM and the other to reset fingerprint sensor Press F1 to accept or F2 to reject If the HP notebook model n
7. the seller Safety warning notice N WARNING To reduce the possibility of heat related injuries or of overheating the device do not place the device directly on your lap or obstruct the device air vents Use the device only on a hard flat surface Do not allow another hard surface such as an adjoining optional printer or a soft surface such as pillows or rugs or clothing to block airflow Also do not allow the AC adapter to contact the skin or a soft surface such as pillows or rugs or clothing during operation The device and the AC adapter comply with the user accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment IEC 60950 iv Safety warning notice Table of contents 1 Product o o PRRRNERRRRRRRUMM A AARA 1 2 External component identification 1 ee eee eee e eere ee eee e e ette no beato betae been Pa see e ao Paese paese eee s obesse 3 3 illustrated paris catalog iss etnia e ERREUR LERRA ERE RAE REM EAA EEEM UEM E Y onakin CEA ERE erhia RE e A bRE 5 Locating the serial number product number and model number sss 5 Tablet major components bora e amec t hoa Doe t psondtanieise nina base mch tait iru ar ido suni 6 Miscellaneo s debe osse er etae edit rA URN RD IRI INE 7 Sequential part number listing icc teciiesissa kteiten Eon aPee ite q
8. use only on Compaq 71200 754940 001 Tablet models Miscellaneous parts Component Spare part number 0 3 W 240 W 50 60 Hz 5 0 V 2 A AC adapter 752105 001 Compaq 7 1300 Tablet equipped with a 7 in LCD TouchScreen IPS display an AllWinner 755970 001 A31S 1 00 GHz quad core processor 1 0 GB LP DDR2 system memory and an 8 0 GB Nand flash drive Compaq 7 1200 Tablet equipped with a 7 in LCD TouchScreen TN display an AllWinner 754938 001 A31S 1 00 GHz quad core processor 1 0 GB LP DDR2 system memory and an 8 0 GB Nand flash drive Screw Kit 754941 001 USB extension cable 753186 001 Sequential part number listing Spare part number Description 752105 001 0 3 W 240 W 50 60 Hz 5 0 V 2 A AC adapter 753186 001 USB extension cable 753192 001 0 3 MP front facing webcamera includes cable and double sided adhesive 753193 001 2 0 MP rear facing webcamera includes cable 754529 001 Microphone includes cable 754934 001 Antenna Kit includes wireless antenna transceiver and cable 754935 001 Back cover for use only on Compaq 7 1200 Tablet models 754936 001 Battery 3 7 V 2800 mAh Li ion includes cables 754938 001 Compaq 7 1200 Tablet equipped with a 7 in LCD TouchScreen TN display an AllWinner A31S 1 00 GHz quad core processor 1 0 GB LP DDR2 system memory and an 8 0 GB Nand flash drive 754939 001 Power volume button board 754940 001 7 in LCD TouchScreen TN dis
9. 0 GB LP 754942 001 DDR2 system memory and an 8 0 GB Nand flash drive Before removing the system board follow these steps Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 13 u 5B oO M Disconnect the battery cable from the system board see Battery on page 15 22 Chapter 5 Removal and replacement procedures Remove the system board 1 2 3 Disconnect the following cables from the system board 1 Front facing webcamera cable see Front facing webcamera on page 20 2 Microphone cable see Microphone on page 19 3 Power volume button board cable see Power volume button board on page 21 4 Release the ZIF connector to which the display panel cable is attached and then disconnect the display panel cable from the system board 5 Release the ZIF connector to which the TouchScreen cable is attached and then disconnect the TouchScreen cable from the system board 6 Speaker cable see Speaker on page 17 Remove the two Phillips PM 1 4x2 75 screws 1 that secure the system board to the display panel assembly Remove the system board 2 ot et System board 23 Reverse this proced
10. 6 8 17 system board removal 22 spare part number 6 8 22 T tablet major components 6 spare part numbers 7 8 specifications 25 tools required 9 transporting guidelines 11 U USB extension cable spare part number 7 USB port 3 v video product description 1 volume control buttons 3 WwW webcamera removal 18 20 spare part numbers 6 7 18 20 wireless antenna removal 16 spare part number 6 7 16 36 Index
11. Compaq 7 1300 Tablet and Compaq 7 1200 Tablet Maintenance and Service Guide IMPORTANT This document is intended for HP authorized service providers only Copyright 2013 Hewlett Packard Development Company L P Bluetooth is a trademark owned by its proprietor and used by Hewlett Packard Company under license SD Logo is a trademark of its proprietor The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein First Edition December 2013 Document Part Number 749988 001 Product notice This guide describes features that are common to most models Some features may not be available on your computer Software terms By installing copying downloading or otherwise using any software product preinstalled on this tablet you agree to be bound by the terms of the HP End User License Agreement EULA If you do not accept these license terms your sole remedy is to return the entire unused product hardware and software within 14 days for a refund subject to the refund policy of your place of purchase For any further information or to request a full refund of the tablet please contact your local point of sale
12. DAT MKV and PMP video formats Supports JPG BMP GIF and PNG photo formats Sensor Accelerometer x x Wireless networking Integrated WiFi option 802 11 b g n with 1 antenna x x External expansion Integrated micro SD Card Reader expandable to 32 GB x x Ports Audio 3 5 mm headphone microphone combo jack x x supports North American type headset only e Micro USB 2 0 supports charging 2 Category Power requirements Description Compaq 7 Compaq 7 1300 Tablet 1200 Tablet Supports a 2800 mAh Li ion battery non removable USB x x charging battery Supports an HP 5V 2A USB AC adapter with duck head DC plug and localized cable plug support Operating system Preinstalled Android 4 2 2 Android 4 3 if possible x x Serviceability End user replaceable part x x e HP 5V 2A AC adapter e USB cable Wired headset Chapter 1 Product description 2 External component identification Item Component Item Component 1 Micro SD Card Reader slot 6 FronHacing webcamera 2 Microphone 7 Power button 3 Micro USB port 8 Volume control buttons 2 Item Component Item Component 4 Audio out headphone Audio in 9 Speaker microphone jack 5 Rearfacing webcamera 4 Chapter 2 External component identification 3 Illustrated parts catalog Locating the serial number product number and model number The product name 1 product model 2 produc
13. a AT EU UNUM dm OUR MIN GR M NUM NUM DT qu 22 vi 20 25 E sg hi o cossas 26 Non volatile memory usage Loses eu DEN IR ERHON ROI Nt PENO EURO HS CEA CUL UbR ps io EA EAR eam eadenaTeReue 28 Q estions and dise sedation carretera pack ap Dicuss babar Da nU iN 31 8 Power cord set requirements iiucssaickebidt eee ER EHE PR eA EMRaNEMEE NEME MEA LARA HAIR E ORE EL OBE X ERE X LER PA CER dA 32 Requirements for all countries iios Reels ratto beet pate Mnt Aet 32 Requirements for specific countries and regions sssssssssssseeeeeeenneeeenn 32 9 Reg hig enna tee niecebeaideess 34 FUG ODE e E a E E E E E 35 1 Product description Category Description Compaq 7 Compaq 7 1300 Tablet 1200 Tablet Product Name Compaq 7 1300 Tablet x Compaq 7 1200 Tablet x Processor AllWinner A31S 1 00 GHz quad core soldered on chip x x SOC processor Panel 7 0 in 1024x600 IPS TouchScreen display panel with x 5 point capacitive touch 7 0 in 1024x600 TN TouchScreen display panel with x 5 point capacitive touch Graphics PowerVR SGX544MP2x8 core x x Memory Supports 1 GB DDR3 x x Mass storage Supports a 8 GB Nand Flash drive x x Audio and video Integrated forward facing speaker x x One microphone Supports MP3 WAV Flac and 3GP audio formats 2 0 MP autofocus rear facing webcamera 0 3 MP fixed focus frontfacing webcamera Supports MOV MPEG4 VOB FLV
14. cement procedures 6 Remove the display panel assembly 3 from the back cover to yo gt Reverse this procedure to install the back cover Battery Description Spare part number Battery 3 7 V 2800 mAh Li ion includes cables 754936 001 Before removing the battery follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 13 Z WARNING To reduce potential safety issues use only the battery provided with the tablet a replacement battery provided by HP or a compatible battery purchased from HP Z CAUTION Removing a battery that is the sole power source for the tablet can cause loss of information To prevent loss of information save your work or shut down the tablet through Windows before removing the battery Remove the battery Battery 15 NCAUTION Before positioning the tablet with the display panel facing down make sure the work surface is clear of tools screws and any other foreign objects Failure to follow this caution can result in damage to the display panel assembly 1 Place the display panel assembly on a flat surface display panel side down with the power button and volu
15. de 802 11 WLAN 4 KBytes to 8 No Yes Stores Programmed at A utility is EEPROM KBytes configuration the factory required for and calibration Tools for writing writing data to data data to this this memory memory are not and is typically made public not made available to the public unless a firmware upgrade is necessary to address a unique issue Webcamera 64 KBits No Yes Store Using a utility A utility is webcamera from the device required for configuration manufacturer writing data to and firmware that can be run this memory from Windows and is typically not made available to the public unless a firmware upgrade is necessary to address a unique issue Fingerprint 512 KBytes Yes Yes Stores By enrolling in Only a digitally reader flash fingerprint HP ProtectTools signed templates Security application can Manager make the call to 30 Chapter 7 Statement of Volatility write to the flash Questions and answers 1 How can the BIOS settings be restored returned to default settings Turn on or restart the computer and press F10 when prompted near the bottom of the display Select File then select Restore defaults c Follow the on screen instructions d Select File save changes and exit then press Enter What kind of configuration data is stored on the DIMM Serial Presence Detect SPD memory module How would this data be written The DIMM SPD memory contains information about the memory module such
16. defaults Questions and answers 31 32 8 Power cord set requirements The wide range input feature of the tablet permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC The 3 conductor power cord set included with the tablet meets the requirements for use in the country or region where the equipment is purchased Power cord sets for use in other countries and regions must meet the requirements of the country or region where the tablet is used Requirements for all countries The following requirements are applicable to all countries and regions The length of the power cord set must be at least 1 0 m 3 3 ft and no more than 2 0 m 6 5 ft All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or 250 V AC as required by the power system of each country or region The appliance coupler must meet the mechanical configuration of an EN 60 320 IEC 320 Standard Sheet C13 connector for mating with the appliance inlet on the back of the tablet Requirements for specific countries and regions Country region Accredited agency Applicable note number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Chapte
17. ear the SSD contents by using the BIOS Setup Secure Erase command option or by using a third party utility designed to erase data from an SSD To run Secure Erase enter BIOS Setup by powering on the system and pressing F10 when prompted near the bottom of the display Select the Security menu and scroll down to the Utilities menu Select Secure Erase and select the desired hard drive 27 Non volatile memory usage 28 Non Volatile Amount Does this Does this What isthe How is data How is this Memory Size memory memory purpose of input into memory Type store retain data this this write customer when power memory memory protected data is removed Real Time Clock 256 Bytes No Yes Stores system Using the F10 This memory is RTC battery date and time Setup utility or not write backed up and limited changing the protected HP CMOS keyboard Microsoft recommends configuration controller data Windows date password memory and time protecting the CMOS F10 Setup utility Controller NIC 64 KBytes not No Yes Store NIC Using a utility A utility is EEPROM customer configuration from the NIC required to accessible and NIC vendor that can write data to firmware be run from this memory DOS and is available from NIC vendor Writing data to this ROM in an inappropriate manner will render the NIC nonfunctional Keyboard ROM 64 KBytes not No Yes Stores firmware Programmed at A utility is customer code the factory required for acc
18. em board see Battery on page 15 Microphone 19 Remove the microphone 1 Unsolder the microphone cables 1 from the system board terminals NOTE When installing the microphone the microphone red cable should be soldered to the system board terminal and the microphone black cable should be soldered to the terminal 2 Release the microphone 2 from the retention molding built into the display panel assembly 3 Remove the microphone and cable Reverse this procedure to install the microphone Front facing webcamera Description Spare part number 0 3 MP frontfacing webcamera includes cable 753192 001 Before removing the front facing webcamera follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 13 wp oN Disconnect the battery cables from the system board see Battery on page 15 20 Chapter 5 Removal and replacement procedures Remove the frontfacing webcamera 1 Release the ZIF connector 1 to which the front facing webcamera cable is attached and then disconnect the front facing webcamera cable from the system board 2 Release the frontfacing webcamera 2 from the rete
19. essible keyboard Code is writing data to mouse amp updated when this memory battery the system BIOS and is available management is updated on the HP website Writing data to this ROM in an inappropriate manner can render the PC nonfunctional DIMM Serial 256 Bytes per No Yes Stores memory Programmed by Data cannot be Presence Detect memory module the memory written to this SPD module 128 information vendor memory when configuration Bytes the module is data programmable installed in a not customer accessible Chapter 7 Statement of Volatility PC The specific write protection method varies by memory vendor Non Volatile Amount Does this Does this What is the How is data How is this Memory Size memory memory purpose of input into memory Type store retain data this this write customer when power memory memory protected data is removed System BIOS 4 to 5 MBytes Yes Yes Store system System BIOS A utility is BIOS code and code is required for PC programmed at writing data to configuration the factory this memory data Code is and is available updated when on the HP the system BIOS website is updated Writing data to Configuration this ROM in an data and inappropriate settings are manner can input using the render the PC F10 setup utility nonfunctional or a custom utility Intel 1 5 0r5 Yes Yes Stores Management The Intel chipset Management MBytes Management Engine Code is is configured to
20. graphics product description 1 grounding guidelines 10 guidelines equipment 12 grounding 10 packaging 11 transporting 11 workstation 11 H headphone jack 4 J jacks audio in 4 audio out 4 headphone 4 microphone 4 M mass storage device product description 1 memory module product description 1 microphone location 3 product description 1 removal 19 spare part number 6 7 19 microphone jack 4 model name 1 o operating system product description 2 P packaging guidelines 11 plastic parts service considerations 9 ports product description 1 power button 3 power cord set requirements 32 power requirements product description 2 power volume button board removal 21 spare part number 6 7 21 processor product description 1 product description audio 1 display panel 1 external expansion 1 graphics 1 mass storage 1 memory module 1 microphone 1 operating system 2 ports 1 power requirements 2 processors 1 product name 1 sensor serviceability 2 video 1 wireless networking 1 product name 1 Index 35 R wireless networking product rearfacing webcamera description 1 location 4 workstation guidelines 11 removal 18 spare partnumber 6 7 18 S Screw Kit spare part number 7 sensor product description 1 service considerations cables 9 connectors 9 plastic parts 9 serviceability product description 2 speaker location 4 removal 17 spare partnumber 6 8 17 Speaker Kit spare part number
21. hScreen TN display panel assembly for use only on Compaq 7 1200 754940 001 Tablet models includes display panel cable and TouchScreen cable Before disassembling the tablet follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet Remove the back cover Tablet component replacement procedures 13 NCAUTION Before positioning the tablet with the display panel facing down make sure the work surface is clear of tools screws and any other foreign objects Failure to follow this caution can result in damage to the display panel assembly 1 Place the tablet on a flat surface display panel side down with the power button and volume buttons toward you 2 Remove the four Torx5 T5M1 4x4 0 screws that secure the back cover to the display panel assembly t LL 1 2 1 3 Turn the tablet display side up with the power button and volume buttons toward yov 4 Insert a plastic case utility tool 1 or similar thin plastic tool into the top edge of the tablet between the back cover and the display panel assembly 5 Lift the top edge of the display panel assembly 2 and swing it up and to the left until it separates from the back cover 14 Chapter 5 Removal and repla
22. ice may function normally for a while then degrade in the internal layers reducing its life expectancy A CAUTION To prevent damage to the tablet when you are removing or installing internal components observe these precautions Keep components in their electrostatic safe containers until you are ready to install them Before touching an electronic component discharge static electricity by using the guidelines described in this section Avoid touching pins leads and circuitry Handle electronic components as little as possible If you remove a component place it in an electrostatic safe container The following table shows how humidity affects the electrostatic voltage levels generated by different activities CAUTION A product can be degraded by as little as 700 V Typical electrostatic voltage levels Relative humidity Event 10 40 55 Walking across carpet 35 000 V 15 000 V 7 500 V Walking across vinyl floor 12 000 V 5 000 V 3 000 V Motions of bench worker 6 000 V 800 V 400 V Removing DIPS from plastic tube 2 000 V 700 V 400 V Removing DIPS from vinyl tray 11 500 V 4 000 V 2 000 V Removing DIPS from Styrofoam 14 500 V 5 000 V 3 500 V Removing bubble pack from PCB 26 500 V 20 000 V 7 000 V Packing PCBs in foam lined box 21 000 V 11 000 V 5 000 V 10 Chapter 4 Removal and replacement preliminary requirements Packaging and transporting guidelines Follow these grounding guideline
23. ith hard ties to the ground Field service kits e Static awareness labels e Materialhandling packages e Nonconductive plastic bags tubes or boxes Metal tote boxes e Electrostatic voltage levels and protective materials The following table lists the shielding protection provided by antistatic bags and floor mats Material Use Voltage protection level Antistatic plastics Bags 1 500 V Carbon loaded plastic Floor mats 7 500 V Metallized laminate Floor mats 5 000 V 12 Chapter 4 Removal and replacement preliminary requirements 5 Removal and replacement procedures Tablet component replacement procedures CAUTION Tablet components described in this chapter should only be accessed by an authorized service provider Accessing these parts can damage the tablet and void the warranty This chapter provides removal and replacement procedures for authorized service provider only parts There are as many as 6 screws that must be removed replaced and or loosened when servicing the tablet Make special note of each screw size and location during removal and replacement Back cover Description Spare part number For use only on Compaq 7 1300 Tablet models 756827 001 For use only on Compaq 7 1200 Tablet models 754935 001 7 in LCD TouchScreen IPS display panel assembly for use only on Compaq 7 1300 755969 001 Tablet models includes display panel cable and TouchScreen cable 7 in LCD Touc
24. me buttons toward you 2 Unsolder the battery cables from the terminals 1 on the system board E NOTE When installing the battery the battery red yellow cable should be soldered to the system board terminal and the battery black cable should be soldered to the system board terminal 3 Remove the battery 2 fe Reverse this procedure to install the battery Antenna board Description Spare part number Antenna Kit includes wireless antenna transceiver and cable 754934 001 Before removing the antenna board follow these steps Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system Disconnect the power from the tablet by unplugging the power cord from the tablet Disconnect all external devices from the tablet Remove the back cover see Back cover on page 13 u 5h WwW NM Disconnect the battery cables from the system board see Battery on page 15 16 Chapter 5 Removal and replacement procedures Remove the antenna board 1 Unsolder the antenna cable from the system board wireless terminal 1 2 Release the antenna cable from the routing channel 2 between the battery and the system board 3 Detach the antenna transceiver 3 from the display panel assembly The antenna transceiver is attached to the display panel assembly with double sided adhesive h a
25. nductor size Power cord set fittings appliance coupler and wall plug must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used Requirements for specific countries and regions 33 9 Recycling When a non rechargeable or rechargeable battery has reached the end of its useful life do not dispose of the battery in general household waste Follow the local laws and regulations in your area for battery disposal HP encourages customers to recycle used electronic hardware HP original print cartridges and rechargeable batteries For more information about recycling programs see the HP Web site at http www hp com recycle 34 Chapter 9 Recycling Index A AC adapter spare part number 7 antenna removal 16 spare part number 6 7 16 Antenna Kit spare part number 6 7 16 audio product description 1 audio in jack 4 audio out jack 4 B back cover removal 13 spare part numbers 6 7 8 13 battery removal 15 spare part number 6 7 15 buttons power 3 volume control 3 c cables service considerations 9 card reader slot 3 connectors service considerations 9 D display panel assembly spare part numbers 6 7 8 13 display panel product description 1 E electrostatic discharge 10 equipment guidelines 12 external expansion product description 1 F front facing webcamera location 3 removal 20 spare part number 6 7 20 G
26. ntion molding built into the display panel assembly 3 Remove the front facing webcamera and cable Reverse this procedure to install the frontfacing webcamera Power volume button board Description Spare part number Power volume button board includes cable 754529 001 Before removing the power volume button board follow these steps 1 Turn off the tablet If you are unsure whether the tablet is off or in Hibernation turn the tablet on and then shut it down through the operating system 2 Disconnect the power from the tablet by unplugging the power cord from the tablet 3 Disconnect all external devices from the tablet 4 Remove the back cover see Back cover on page 13 5 Disconnect the battery cables from the system board see Battery on page 15 Remove the power volume button board 1 Release the ZIF connector 1 to which the power volume button board cable is attached and then disconnect the power volume button board cable from the system board Power volume button board 21 2 Detach the power volume button board 2 from the display panel assembly The power volume button board is attached to the display panel assembly with double sided adhesive 3 Remove the power volume button board and cable Reverse this procedure to install the power volume button board System board Description Spare part number System board equipped with an AllWinner A31S 1 00 GHz quad core processor 1
27. play panel assembly for use only on Compaq 7 1200 Tablet models 754941 001 Screw Kit Miscellaneous parts 7 8 Spare part number Description 754942 001 System board equipped with an AllWinner A31S 1 00 GHz quad core processor 1 0 GB LP DDR2 system memory and an 8 0 GB Nand flash drive 755197 001 Speaker Kit includes speaker and cables 755969 001 7 in LCD TouchScreen IPS display panel assembly for use only on Compaq 7 1300 Tablet models 755970 001 Compaq 7 1300 Tablet equipped with a 7 in LCD TouchScreen IPS display an AllWinner A31S 1 00 GHz quad core processor 1 0 GB LP DDR2 system memory and an 8 0 GB Nand flash drive 756827 001 Back cover for use only on Compaq 7 1300 Tablet models Chapter 3 Illustrated parts catalog 4 Removal and replacement preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures e Magnetic screw driver e Phillips PO screw driver Plostic case utility tool e Torx T5 screw driver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures NOTE As you remove each subassembly from the tablet place the subassembly and all accompanying screws away from the work area to prevent damage Plastic parts Z CAUTION Using excessive force during disassembly and reassembly can damage plastic par
28. r 8 Power cord set requirements Country region Accredited agency Applicable note number Germany VDE 1 Italy IMQ 1 Japan METI 3 The Netherlands KEMA 1 Norway NEMKO 1 The People s Republic of China COC 5 South Korea EK 4 Sweden CEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1 The flexible cord must be Type HO5VV F 3 conductor 1 0 mm conductor size Power cord set fittings appliance coupler and wall plug must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used The flexible cord must be Type SPT 3 or equivalent No 18 AWG 3 conductor The wall plug must be a two pole grounding type with a NEMA 5 15P 15 A 125 V or NEMA 6 15P 15 A 250 V configuration The appliance coupler flexible cord and wall plug must bear a T mark and registration number in accordance with the Japanese Dentori Law The flexible cord must be Type VCT or VCTF 3 conductor 1 00 mm conductor size The wall plug must be a two pole grounding type with a Japanese Industrial Standard C8303 7 A 125 V configuration The flexible cord must be Type RVV 3 conductor 0 75 mm conductor size Power cord set fittings appliance coupler and wall plug must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used The flexible cord must be Type VCTF 3 conductor 0 75 mm co
29. s by the case or PCM laminate Handle these items only at static free workstations Avoid contact with pins leads or circuitry Turn off power and input signals before inserting or removing connectors or test equipment Grounding guidelines 11 Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation e When seated wear a wrist strap connected to a grounded system Wrist straps are flexible straps with a minimum of one megohm 10 resistance in the ground cords To provide proper ground wear a strap snugly against the skin at all times On grounded mats with banana plug connectors use alligator clips to connect a wrist strap e When standing use foot straps and a grounded floor mat Foot straps heel toe or boot straps can be used at standing workstations and are compatible with most types of shoes or boots On conductive floors or dissipative floor mats use foot straps on both feet with a minimum of one megohm resistance between the operator and ground To be effective the conductive must be worn in contact with the skin The following grounding equipment is recommended to prevent electrostatic damage e Antistatic tape e Antistatic smocks aprons and sleeve protectors e Conductive bins and other assembly or soldering aids e Nonconductive foam e Conductive tabletop workstations with ground cords of one megohm resistance e Staticdissipative tables or floor mats w
30. s when packaging and transporting equipment To avoid hand contact transport products in static safe tubes bags or boxes Protect ESD sensitive parts and assemblies with conductive or approved containers or packaging Keep ESD sensitive parts in their containers until the parts arrive at static free workstations Place items on a grounded surface before removing items from their containers Always be properly grounded when touching a component or assembly Store reusable ESD sensitive parts from assemblies in protective packaging or nonconductive foam Use transporters and conveyors made of antistatic belts and roller bushings Be sure that mechanized equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging When grounding is not possible use an ionizer to dissipate electric charges Workstation guidelines Follow these grounding workstation guidelines Cover the workstation with approved static shielding material Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment Use conductive field service tools such as cutters screw drivers and vacuums When fixtures must directly contact dissipative surfaces use fixtures made only of static safe materials Keep the work area free of nonconductive materials such as ordinary plastic assembly aids and Styrofoam Handle ESD sensitive components parts and assemblie
31. t number 3 and serial number 4 of your tablet are located on the bottom edge of the tablet You may need this information when you travel internationally or when you contact support Compaq 7 Model 1200 PN F6HBIAASAB2 SN 8CA3410001 BS RMN HSTNN NO1C Locating the serial number product number and model number B 6 Tablet major components Item Component Spare part number 1 Back cover For use only on Compaq 7 1300 Tablet models 756827 001 For use only on Compag 7 1200 Tablet models 754935 001 2 Battery 3 7 V 2800 mAh Li ion includes cables 754936 001 3 Antenna Kit includes wireless antenna transceiver and cable 754934 001 4 Microphone includes cable 754529 001 5 0 3 MP front facing webcamera includes cable and double sided adhesive 753192 001 6 Speaker Kit includes speaker and cables 755197 001 7 2 0 MP rear facing webcamera includes cable 753193 001 8 System board equipped with an AllWinner A31S 1 00 GHz quad core processor 754942 001 1 0 GB LP DDR2 system memory and an 8 0 GB Nand flash drive 9 Power volume button board includes cable 754939 001 10 Display panel assembly includes display panel cable and TouchScreen cable Chapter 3 Illustrated parts catalog Item Component Spare part number 7 in LCD TouchScreen IPS display panel assembly for use only on Compaq 7 1300 755969 001 Tablet models 7 in LCD TouchScreen TN display panel assembly for
32. ts Use care when handling the plastic parts Apply pressure only at the points designated in the maintenance instructions Cables and connectors Z CAUTION When servicing the tablet be sure that cables are placed in their proper locations during the reassembly process Improper cable placement can damage the tablet Cables must be handled with extreme care to avoid damage Apply only the tension required to unseat or seat the cables during removal and insertion Handle cables by the connector whenever possible In all cases avoid bending twisting or tearing cables Be sure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced Handle flex cables with extreme care these cables tear easily Tools required Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge ESD Circuitry design and structure determine the degree of sensitivity Networks built into many integrated circuits provide some protection but in many cases ESD contains enough power to alter device parameters or melt silicon junctions A discharge of static electricity from a finger or other conductor can destroy static sensitive devices or microcircuitry Even if the spark is neither felt nor heard damage may have occurred An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle Or the dev
33. u Un etu pM E IDE uM pieni Reque LR UE 7 4 Removal and replacement preliminary requirements cesse eese eee eene eee en eene rennen 9 Tools reg ired MC T 9 Service considerations scc corner trrsdrvx dE PUR saved eri Far npn ut ego rH Oder pere Rer MEYER PErpURTIR SE yes 9 Plastic pars acoie aaeeseda ancien a T E ERO DM ROUTE 9 Cables and connectors jean cotinine avi eve iise iina i e ea der am e 9 Grounding guidelines issar rare iaia aE pE ia api in iNES E ae HEN EEE ER RIS MEE 10 Electrostatic discharge damage sooo e DER IHRER NE ainsi SPUR tA ERTU RUE UE He Un bI NER 10 Packaging and transporting guidelines sssssssee 11 Workstation guidelines ecciesia ie e ob err tetra s bn xoi 11 5 Removal and replacement procedures ecce eee eL eee eee ee eee eee ee enne eene esas e esso ee onoe 13 Tablet component replacement procedures ccceeecceeeeseeeeeeeeeseeeeeseeeeeeeeneeeeecseeeeceseeeeetseeeeess 13 Back COVE MONTE E TOTO 13 Banery onoare M UU 15 Antenna board MTM T P ie o i ea aaa A E a a a i 16 Speaker seye a r E A S a a E A 17 Rearfacing webcamera acscsccnekeateimessitbe Ia AE E ME E Minn 18 NTE rae e e a e e A EN ReuP DUK 19 Fr nifacing Webcamera E TTE ETT nna PEA aa E ba EEA ET m 20 Power volume button board ccccccccsececccecccecceccceccecececuceececuaeececutececauaeeeceaeceecaeseeecaueseeeteteeaes 21 Syslem BEN oeste ied dad
34. umber ends in a p or w and includes Intel Centrino with VProTM reboot the PC and enter BIOS Setup by pressing F10 when prompted Select System Configuration then AMT Options Then select Un configure AMT on next boot Select Save then Yes Select the File menu and then select Save Changes and Exit Reboot the system and confirm that you want to un configure AMT If the optional Intel Anti Theft Technology AT was activated contact the provider to deactivate it If the optional Absolute Software Computrace management and tracking service was activated on the notebook PC contact the provider to deactivate it Remove all power and system batteries for at least 24 hours Remove and retain the storage drive or clear the contents of the drive Hard Disk Drive HDD Clear the HDD contents by using the HP Disk Sanitizer utility or a third party application that ideally is U S Department of Defense DOD 5220 22 M approved To run HP Disk Sanitizer enter BIOS Setup by powering on the system and pressing F 10 when prompted near the bottom of the display or press ESC to display the start up menu then press F10 Select the Security menu and scroll down to the Utilities menu Select Disk Sanitizer and select the desired drive For a higher level of protection select Optimum A NOTE This process will take a long time and the amount of time varies based on the hard drive capacity Solid State Drive SSD Cl
35. ure to install the system board 24 Chapter 5 Removal and replacement procedures 6 Specifications Metric U S Dimensions Width 12 2 cm 4 8 in Depth 0 8 cm 0 3 in Height 19 3 cm 7 6 in Weight lowest weight configuration 0 32 g 0 70 Ib Input power The tablet operates on DC power which can be supplied by an AC or a DC power source The AC power source must be rated at 100 240 V 50 60 Hz NOTE The tablet can operate on DC power using an industry standard micro A or micro B USB cable The HP 5V 2A adapter included with your tablet is recommended for charging the tablet Temperature Operating 5 C to 35 C 41 F to 95 F Nonoperating 20 C to 60 C 4 F to 140 F Relative humidity non condensing Operating 10 to 90 Nonoperating 5 to 95 Maximum altitude unpressurized Operating 15 m to 3 048 m 50 ft to 10 000 ft Nonoperating 15 m to 12 192 m 50 ft to 40 000 ft NOTE Applicable product safety standards specify thermal limits for plastic surfaces The device operates well within this range of temperatures 25 7 Statement of Volatility 25 The purpose of this document is to provide general information regarding non volatile memory in industry standards based HP Business Notebook PC systems and provide general instructions for restoring nonvolatile memory that can contain personal data after the system has been powered off and the hard drive has been removed
Download Pdf Manuals
Related Search