Solaris 5 - DirectedDealers.com
Contents
1. o o o o o Control Unit The brain of your system Usually hidden underneath the dash area of the vehicle It houses the microprocessor which mon itors your vehicle and controls all of the system s functions Input A physical connection to the system An input can be provided by a sensor pinswitch or through an existing system in the vehicle such as ignition or courtesy lights LED Blue light mounted somewhere in the vehicle It is used to indi cate the status of your system It is also used to report triggers and faults in the system or sensors PlainView 2 Valet Switch A small two button switch mounted some where inside the vehicle It is used to override the alarm when a trans mitter is lost or damaged or to enter or exit Valet mode Siren Noise generating device usually installed in the engine compart ment of the vehicle It is responsible for generating the chirps you hear as well as the six tones you hear while the alarm is triggered Transmitter Hand held transmitter which operates the various func tions of your system Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered response of your system consists of the siren sounding and parking light flashing for the programmed duration 2004 directed electronics inc 41 UltraSecure Immobilizer A feature on the module which prevents the vehicle s engine from operating whenever the system is2. contents eee limited lifetime consumer low battery warning 14 Walranty lt 3 i00 taste ce al dada i multiple event total recall 14 trademarks and copyrights ii abe alarini Control xs eacineee ra technology FACT Il 15 what is included 3 select siren sounds 16 important information 3 diagnostics 16 system maintenance 4 your Warranty 4 amning le ghost EP RR 16 FC n ta pa a 4 disarming diagnostics 17 arm disarm diagnostic chart 17 transmitter configurations 5 table of zones 18 transmitter functions 6 i anti code grabbing ACG 18 standard configuration 6 high frequency 19 using your system 8 arming with transmitter 8 smart power up Il 19 arming without transmitter 8 power saver mode 20 disarming 9 programming 21 disarming withouta cliffnet wizard installation transmitter 10 software programming 21 remote siren silencing 10 manual programming transmitter chirp muting 10 instructions 21 transmitter sensor disable 11 user selectable features 23 intellistart and smart user selectable features windows sensor bypass 11 descriptions column one 24 auxiliary channel bypas
3. All rights reserved G909610 08 04
4. e Press i to decrease sensitivity e The sensor Primary zone can be tested at any time dur ing adjustment by striking the vehicle which will gen erate 1 siren chirp each time the zone is activated 4 Press X 3 to adjust Warn Away zone e Siren chirps 1 time e Warn away Zone adjustment has now been entered e Warn away Zone can now be adjusted 5 Adjust Warn away Zone NOTE There are 16 distinct pitch settings if the upper or lower limit of the 16 settings is reached the siren will emit 2 chirps at the default pitch e Press Gm of the remote control to increase sensitivity The siren chirps will increase in pitch e Press i of the remote control to decrease sensitivity The siren chirps will decrease in pitch e The sensor Warn away zone can be tested at any time during adjustment and will generate 1 siren chirp each time the zone is activated 6 Press aa of the remote control to return to Primary zone adjustment and lock in Warn Away zone setting e Siren chirps 2 times e Primary zone can now be re adjusted as described in step 3 e Or press aa again to lock in primary zone setting and exit programming mode e The siren will chirp 3 times when sensor adjustment mode has been exited 2004 directed electronics inc 39 40 Auto Scroll for adjusting sensitivity press and hold Gm or Xe to increase or decrease sensitivi ty setting several levels rapidly CLIFFORD ES glossary of terms
5. are deterrents against possible theft Directed is not offering a guarantee or insurance against vandalism damage or theft of the automobile its parts or contents and hereby expressly disclaims any liability whatsoever including without limitation liability for theft damage and or vandalism Directed does not and has not autho rized any person or entity to create for it any other obligation promise duty or obligation in connection with this security system Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following e Date of purchase e Your full name and address e Authorized dealer s company name and address e Type of alarm installed e Year make model and color of the automobile e Automobile license number e Vehicle identification number e All security options installed on automobile e Installation receipts importanti Please note that this manual was intended for US consumers and therefore includes American phrases or words trademarks and copyrights lt Bitwriter Clifford Code Hopping Directed Doubleguard ESP FailSafe Ghost Switch Learn Routine Nite Lite Nuisance Prevention Circuitry NPC Revenger Silent Mode Soft Chirp Stealth Coding Stinger Valet Vehicle Recovery System VRS and Warn Away are all Trademarks or Registered Trademarks of Directed Electronics Inc CLIFFORD ES
6. brake the remote start will turn off and the engine will stay running You are ready to drive CLIFFORD ES shortstop mode Shortstop mode is a convenience feature that allows the remote start to keep the engine running while you run a brief errand In Shortstop mode the security section of your system will operate normally should you want to activate it To activate shortstop mode e Park the vehicle place the shifter into park and engage the handbrake Place the shifter into the neutral position if it is a manual transmission e Without pressing the brake pedal press the 7 button of your remote control The lights will flash 2 times as confir mation e Turn the ignition off and remove the keys from the ignition switch The engine will continue to run Exit the vehicle arm the security system and attend to your business The engine will run for the programmed run time low temperature battery start Your remote start system can automatically start your vehicle if the inte rior reaches a pre programmed low temperature setting or if the bat tery charge level drops too low Both these settings can be calibrated and set using the Cliffnet Wizard It is recommended that you have your installer calibrate and set the start time intervals if you intend to use this feature 2004 directed electronics inc 35 To activate autostart mode e Armthe security section of your system e Transmit the Autostart command the
7. may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation Directed Electronics Inc Model Number XHF Tested to Comply C with FCC Standards DRW 396 CUFFORD ES transmitter configurations Remote Start or Accessory Output Button Silent Arm Disarm or Accessory Output Button Arm Disarm and Panic Button Trunk Release or Optional Accessory Channel Button Shift Button note This manual describes the features and accessories that are included with your system along with information about compatible Clifford accessories that are not included For a list of included acces sories please refer to the What Is Included section of this manual 2004 directed electronics inc CLIFFORD transmitter functions This system uses computer based code learning to learn the transmit ter buttons This makes it possible to assign any transmitter button to any system function The transmitter initially comes programmed with standard configuration but may also be customized using the CliffNet Wizard PC program The buttons in all of the instructions in this man ual correspond to a standard configuration transmitter standard configuration D Q Button The arming disarming and panic function are controlled by this button sp Button The trunk release or accessory output A is controlled by this butt
8. pressing k 1 9 times and then press LJ to enter the number into the system To enter a zero press only To program a PIN code of 1032 1 Press and release Ed once and E once You will hear one chirp 3 Press and release once You will not hear a chirp after programming a zero 5 Press and release three times and then press C once You will hear three chirps 6 Press and release 3 two times and then press U once You will hear two chirps Wait for two siren chirps after a five second pause or five seconds after the last digit has been entered if using less than four digit code number Turn off the ignition the siren will chirp three times The programming mode is now exited CUFFORD ES PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set 1 Turn on the ignition Enter the new PIN code 3 Press and hold T for three seconds e LED turns on New PIN code is learned and program ming is complete e LED stays off New PIN code is not learned and the sys tem reverts to the old PIN code Repeat the program ming sequence 2004 directed electronics inc 31 remote start remote start features e Remotely start your car s engine from hundreds of feet away e Automatically performs extensive pre start safety checks e Automatic cold weather cranking for hard start conditions e Activates all preset
9. CLIFFORD button twice then the J 3K button once The lights will flash 2 times as confirmation of Autostart mode e The remote start will monitor the temperature and battery levels and start at the programmed settings and intervals retained accessory power The remote start section of this system will after turning off the igni tion keep the accessory power of the vehicle on for 5 minutes or until the vehicle door is opened This is very convenient if you forgot to roll up windows or just want to listen to the radio diesel compatibility the system will activate the engine s glow plugs for the necessary dura tion before starting via either a timer delay or through a direct connec tion to your vehicle s glow plug indicator may require optional parts or wiring Si 36 CLIFFORD ES auto immobilization feature Auto immobilization is a feature designed for maximum security it activates the UltraSecure Immobilization circuitry automatically auto immobilization sequence 1 Turn ignition off or disarm alarm 2 After 30 seconds the systems Immobilization circuits activate and engage the starter and ignition interrupt 3 LED blinks at normal speed Disarming auto immobilization To disarm auto immobilization when active follow any of the sequences listed below e Turn ignition on and press the arm disarm button e Armthe alarm and then disarm the alarm e Turn the ignition on and ente
10. R THEFT DAMAGE AND OR VANDALISM THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUN TY IN THE STATE OF CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE UNIT DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCI DENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL 2004 directed electronics inc i LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON TROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights that vary from State to State This product may be covered by a Guaranteed Protection Plan GPP See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1 800 876 0800 Directed security systems including this unit
11. Solaris Do Owner s Guide Directed Electronics Inc Directed promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit hereafter the unit excluding without limitation the siren the remote transmitters the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use during the life time of the vehicle provided the following conditions are met the unit was professionally installed and serviced by an authorized Directed dealer the unit will be professionally rein stalled in the vehicle in which it was originally installed by an authorized Directed dealer and the unit is returned to Directed shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information consumer s name telephone num ber and address the authorized dealers name telephone number and address complete prod uct description including accessories the year make and model of the vehicle vehicle license number and vehicle identification number All components other than the unit including with out limitation the siren the remote transmitters and the associated sensors and accessories carry a one year warranty from the date of purchase of the same This warranty is non trans ferable and is automatically void if the original purchaser has not completed the warranty card and mailed it within ten 10 days of
12. accessories such as the heater or AC e Monitors RPM and shuts down the engine if problems are detected e Clifford security system remains armed throughout e Automatically bypasses triggered security sensors e Automatically shuts down the engine if the alarm sounds Auto shutdown after 30 minutes if left unattended e Prevents the starter from engaging if the driver turns the ignition key too far e ShortStop lets you remove the key and arm the alarm for a brief errand while the engine continues to idle e Selectable low temp autostart warm up for very cold weather e Selectable low battery autostart recharging e Extended accessory power after ignition is turned off e Automatic transmission compatibility Si 32 CLIFFORD ES note this product must be installed by an authorized Directed dealer in accordance with the instructions supplied It is intended for automo biles with a 12V battery and a gas or diesel powered electronic fuel injected engine Your authorized Directed dealer can correct any wiring problems and if necessary can return any malfunctioning com ponent to Directed Electronics for repair replacement under the war ranty terms and conditions noted in this manval remote start do s and don ts Do s Don ts Park in a well ventilated area if you should plan on remote starting your vehicle Engage the parking brake at all times Place the transmission in PARK or NEUTRAL manua
13. agnostics i The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it It detects any faulty switches and sensors and prevents them from dis abling the entire system The microprocessor will also record and report any triggers that occurred during your absence arming diagnostics If the system is armed while an input is active door open sensor trig gering etc the unit will chirp as listed on the alarm disarm diagnostic chart next page This is called Bypass Notification 16 CLIFFORD 29 The security system will ignore the input that was active when the sys tem was armed until the input goes away Three seconds later the sys tem will monitor that input normally 1 If a door is open the siren will chirp 4 times 5 seconds after the 2 arming chirps 2 Ifa sensor is active the siren will chirp 4 times 10 seconds after the 2 arming chirps 3 Ifthe hood or trunk is open the siren will chirp 4 times upon arming disarming diagnostics Extra disarm chirps are the Tamper Alert If three chirps are heard when disarming the system was triggered in your absence If three chirps are heard the LED status indicator will indicate which zone was involved when you turn the ignition on see the Table of Zones section The sys tem will retain this information in its memory Refer to the Multiple Event Total Recall section of this guide arm d
14. alse alarms After the third trigger FACT Il ignores or bypasses that sensor along with any other sensors sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continually triggers will remain bypassed Doors are covered by FACT differently if the alarm is triggered by an open door for three full cycles the doors will be bypassed until the trig ger ceases FACT II is programmable See the Programming Options section of this guide note Arming and disarming the system does not reset this function The only way to reset a bypassed zone is for 60 minutes or fo turn on the igni tion If testing your system it is important to remember that the FACT II pro gramming can cause zones to be bypassed and appear to stop working If you wish to clear the FACT Il memory turn the ignition key on 2004 directed electronics inc 15 select siren sounds To customize siren sounds please refer to the selectable siren sounds feature in the User Selectable Features grid Once in programming mode press aa on the transmitter to begin playback of the avail able sounds Press LJ on the PlainView 2 Valet switch while playing the desired sound to add that sound press EJ while playing the desired sound to delete that sound note Additional tones can be accessed through the CliffNet Wizard di
15. and have the PIN code Be sure to check with the installer for the location of the PlainView 2 Valet switch Please refer to the Disarm Valet Mode section of this guide for instruc tions to enter the pin code remote siren silencing This system offers remote siren silencing Remote siren silencing is a fea ture that makes it possible to silence and reset the system when it is triggering without disarming the system If the system is triggered and the siren has been sounding press aa on the transmitter to stop the trigger and return the unit to the armed state This prevents you from disabling the system should you wish to silence it without visually checking the vehicle After resetting the system press aa again to disarm the system transmitter chirp muting To temporarily turn off the arm or disarm chirps use transmitter chirp muting Simply press 7 JK on the transmitter and the confirmation chirp s will be eliminated for that one operation only The parking lights will flash to confirm the arm disarm command If you want the arm disarm chirps turned off permanently please refer to the User Selectable Features section of this guide Si 10 CLIFFORD ES transmitter sensor disable To temporarily disable a sensor input arm the system press CLIFFORD twice and then s amp The lights will flash four times and all sensor warn away ones are bypassed Press the buttons again the lights flash four times and both warn away and full t
16. armed The vehicle is never prevented from running when the system is disarmed in Valet mode or loss of power Warning Zone Response Lighter impacts or movement close to the vehi cle will generate the Warning Zone response It consists of a warning siren blast or beep Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Two or more inputs often share the same zone Si 42 CLIFFORD ES security amp convenience expansions Here we have listed only some of the many expansion options avail able Please contact your dealer for a complete list of all the options available to you Backup Battery The 520T keeps the system armed triggers the alarm and keeps the immobilization circuits active if main battery power is discon nected Power Trunk Release The button can operate a factory power release for the vehicle s trunk or hatch An optional relay may be re quired If the factory release is not power activated the Directed s 522T trunk release solenoid can often be added Power Window Control Automatic power window control is provided with the SmartWindows system Remote Start System For the ultimate in convenience the IntelliStart remote start system can start your vehicle monitor engine functions and power your climate control system with a push of a button Over rev protection open hood lockout brake pedal shutoff and autom
17. at ic timer shutoff are all included 2004 directed electronics inc 43 44 CUFFORD ES health check Directed Electronics recommends you return to your installing Clifford dealer to have your system checked for correct operation The first check is due one year after the installation date and at yearly intervals thereafter note There may be a small charge incurred for this service Signed Dated Signed Dated Signed Dated Signed Dated Signed Dated Signed Dated 2004 directed electronics inc 45 The company behind this system is Directed Electronics Inc Since its inception Directed has had one purpose to provide consumers with the finest vehi cle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world E amp OE specification is subject to change without notice Some vehicles require optional parts wiring and a few are incompatible with some features DEI is an ISO 9001 registered company Directed is committed to delivering world class quality products and services that excite and delight our customers driven to excel Dixcectea ELECTRONICS INC Vista CA 92081 www directed com 2004 Directed Electronics Inc
18. ed into this feature will activate the accessory output silent mode The transmitter channel programmed into this feature will arm disarm the system but the siren will not chirp remote valet The transmitter channel programmed into this feature will make the system enter exit valet mode 28 CLIFFORD 29 remote start e This feature is only available with IntelliStart connected e The transmitter channel programmed into this feature will activate or shut down the Intellistart remote start system window control e This feature is only available with SmartWindows connected e The transmitter channel programmed into this feature will activate the vent or roll down feature of the SmartWindows system clear all remotes e This feature will erase all remote codes from the system memory This feature is convenient for erasing any transmit ters that have been lost stolen or incorrectly programmed into the system e After entering this feature press any button on the transmit ter the siren will chirp to indicate that all transmitters have been erased from memory 2004 directed electronics inc 29 pin programming i A PIN code can have one to four digits each digit can be from 0 9 note A PIN code cannot begin with a zero Programming Procedure 1 2 30 Enter the feature location in the installer programming grid Immediately press and release LJ of the PlainView 2 Valet switch Select each digit by
19. gered during the arming countdown the 30 second countdown starts over When armed your vehicle is protected as follows e The LED will flash as a visible theft deterrent e Light impacts will trigger the Warning Zone signal When triggered the siren will sound for a few seconds e Heavy impacts will trigger the system The triggered sequence is 30 60 or 90 seconds of constant siren sounding and flashing parking lights e If a protected entry door hood or trunk is opened the sys tem will immediately trigger the siren and flash the parking lights disarming To disarm the system press aa You will hear a chirp and the park ing lights will flash once If the power locks are connected to the sys tem the doors will unlock If the siren chirps three times when disarm ing refer to the Diagnostics section of this guide This is called Tamper Alert If the siren is active when the system is disarmed you will hear two chirps but the system is not disarmed Refer to the Remote Siren Silencing section of this guide However if the alarm completes the full trigger cycle when disarmed you will hear three chirps 2004 directed electronics inc 9 disarming without a transmitter This feature allows you to disarm the system without the transmitter should it be lost damaged or disabled In order to disarm without a transmitter you must have the vehicle s ignition key know where the PlainView 2 Valet switch is located
20. he control unit knows what the next codes should be Si 18 CLIFFORD ES high frequency o o oo Your system transmits and receives at 433 MHz This provides a cleaner spectrum with less interference and a more stable signal smart power up ees This security system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the bat tery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode 2004 directed electronics inc 19 power saver mode i Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a period of time in which no operation has been performed This lowers the current draw on the vehicle s battery and prevents the system from draining the battery Power Saver Mode takes over under the following conditions e Power Saver when the system is armed After the system has been armed for 48 hours the LED will flash at half its nor mal rate decreasing the system s current draw e Power Saver in Valet Mode When the system enters Valet Mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a period of one hour while the system is in Valet Mode the LED will sh
21. isarm diagnostic chart Action Arm Arm Arm Arm Disarm Disarm Chirps 2 4 2 5 sec 4 2 10 sec 4 2004 directed electronics inc Light Flashes 2 4 2 5 sec 4 2 10 sec 4 Description System armed System armed with hood trunk active and bypassed zones 5 and 6 System armed with door active and bypassed zone 4 System armed with sensor active and bypassed zones 1 3 and8 System disarmed System disarmed with tamper alert 17 table of zones The zone number is the number of LED flashes used by the system to identify a specific input The standard input assignments are listed below along with spaces to write in any optional sensors or switches you have had installed If the Warning Zone response is triggered the LED will not report it Zone Number Dealer Installed of LED Flashes Description Options 1 Data Dual zone shock sensor 2 Not used 3 Mux 1 trigger for optional sensors 4 Door switch trigger 5 nstant trigger trunk 6 nstant trigger hood 7 gnition trigger 8 Mux 2 trigger for optional sensors 9 Not used 10 Power interrupt anti code grabbing ACG i This unit features Anti Code Grabbing ACG with Random Code Encryption This means the receiver and transmitters each use a math ematical formula called an algorithm to change their code each time the transmitter is used This technology has been developed to increase the security of the unit T
22. l arm 25 seconds later chirps off on quiet Off Chirps will not sound when arming disarming the system On Chirps will sound when arming disarming the system Quiet Chirps will sound when arming disarming the system but at a lower volume than normal auto lock off ignition rpm 24 Off The doors will not lock automatically Ignition The doors will automatically lock three seconds after the ignition is turned on unless a door is open at that time Rpm The doors will lock when the system sees the engine reach a preprogrammed RPM CUFFORD ES auto unlock off ignition e Off The doors will not automatically unlock when the igni tion is turned off e ignition The doors will automatically unlock as soon as the ignition is turned off auto passive arm and lock off on e Off The doors will not lock when the system passively arms e On The doors will lock when the system passively arms This feature only applies when passive arming is programmed on siren duration 30 60 90 e The system will sound the alarm for the programmed dura tion 30 60 90 seconds during an alarm trigger or when the system is put into panic mode second unlock off on e Off Second unlock output is pulsed at the same time as the unlock output when the system is disarmed e On Second unlock output is active when the arm disarm button is pressed within 10 seconds of disarming the system note The second unlock can be insta
23. l trans before shutting the engine off Preset your comfort controls according to the conditions of the vehicles interior when remote start is activated Always make sure the vehicle has sufficient petrol DON T remote start your vehicle or engage Shortstop or Autostart modes in an enclosed area such as a garage or car port DON T allow children access to your remote control DON T engage remote start or Shortstop or Autostart modes when children or pets are present in the vehicle DON T remote start the vehicle when someone is in front or behind the vehicle 2004 directed electronics inc 33 remote start engine shut down To remotely start your vehicle press for one second When starting The lights will flash 2 times as confirmation to start The ignition and preset accessories will start and run for the programmed run time The lights will stay on as a visual indicator that the engine is running To remotely shut off your vehicle press the button of the remote control for 1 second The engine will shut off and the lights will go out Drive vehicle after remote starting After your vehicle has been remotely started you can enter and drive away without having to restart 34 Disarm the security section of your system as you normally would Enter the vehicle without stepping on the brake or moving the shift lever Insert your key into the ignition and turn to the run position Step on the
24. lled by your dealer Please note that extra parts and labor may be required 2004 directed electronics inc 25 user selectable features descriptions column two set pin code This feature allows the setting of the user s personal PIN code For more information please refer to the PIN Programming section of this guide select siren sounds The individual sounds the siren produces during an full trigger alarm can be customized for owner recognition of an alarm trigger For more infor mation please refer to the Select Siren Sounds section of this guide note Sounds 7 through 15 available using CliffNet Wizard fact Il off on Off The alarm will respond to sensor inputs indefinitely without bypassing On The alarm will bypass for 60 minutes if a sensor is trig gered three times within a one hour period remote valet off on Off The alarm can not be put into valet mode with the remote control On The alarm can be put into valet mode with the remote control entry delay off on 26 Off There is no entry delay when armed The system will trigger instantly when a door is opened On If the system has passively armed it will not trigger for 15 seconds after a door is opened allowing the user to enter the vehicle and disarm the system via the PlainView 2 Valet switch CLIFFORD ES reset to default settings All system settings except PIN and remote programming in the User Programming grid will be re
25. n select Press J the same number of times as the desired column After a pause the siren will chirp the same number of times as the selected column for confirmation Feature select Press x the same number of times as the desired feature The siren will chirp with each press The fea ture can now be changed using the remote control Feature change Press aa on the transmitter If the sys tem chirps once the feature has just turned off if the sys tem chips twice the feature has just turned on If the fea ture has more than two settings continue pressing VO on the transmitter to toggle through the settings You can advance to any feature in the same column by pressing within 60 seconds to program a feature in a different column begin at step 4 within 60 seconds note Refer to the Feature Descriptions sections of this guide for impor tant notes and descriptions of the system features and programming Exit programming To exit programming mode turn the igni tion off or wait 60 seconds without pressing the PlainView 2 Valet switch The siren will chirp three times to indicate pro gramming mode has been exited CLIFFORD ES user selectable features First Press Add new remote autolearn Auto passive arm off on New remote learn arm disarm only New remote learn accessory A channel Set PIN code default 2 Select siren sounds Chirps off on quiet Auto lock off ignition rpm Auto unl
26. ock off ignition FACT II off on Remote valet off on Entry delay off on New remote learn accessory B channel New remote learn silent mode New remote learn remote valet Auto passive arm and lock off on Siren duration 30 60 90 Second unlock off on New remote learn remote start Reset to default except transmitter and valet code Panic on off Autostart setting off battery only temp only battery and temp New remote learn window down vent Not used Not used Not used Clear all remotes This feature is only available with optional IntelliStart connected This feature is only available with optional SmartWindows connected 2004 directed electronics inc 23 user selectable features descriptions column one add new remote auto learn Auto learn new five button Radar2 remote controls to the system in the standard button configuration Once you have entered the feature press YQ on the transmitter until you hear a confirmation chirp Press again until you hear two chirps indicating the new remote is learned auto passive arm off on Off The transmitter must be used to arm the system On When the system sees the ignition turn off and the last protected entry door hood or trunk close it will begin a 30 second countdown before arming itself After the first five seconds you will hear two chirps and the lights will flash The system wil
27. ode Entering your pin code using the PlainView 2 Valet switch allows you to disarm the system or enter valet mode without using the transmit ter In valet mode the security system will not arm even with the trans mitter but all convenience functions door locks trunk release etc will continue to work normally To disarm or enter Valet Mode 1 Turn the ignition on S 2 Enter PIN code factory setting is 2 this proce i dure is described later in this manual 9 No Si 12 CLIFFORD ES 3 After the last digit of the pin code is entered a To disarm the system press and release D b To enter valet mode Press and hold E for three seconds The LED status indicator will light steadily when Valet Mode has been entered To exit Valet Mode 1 Turn the ignition on Fi 2 Enter PIN code Zo 3 After the last digit press E for one second The LED status indicator will turn off when valet mode has been exited To enter or exit Valet Mode To enter or exit Valet Mode press CLIFFORD twice and then f VQ The LED status indicator will light solid when Valet Mode is entered or will turn off when Valet Mode is exited 2004 directed electronics inc 13 one time auto arming bypass This will bypass the auto arm feature once only 1 With the key turn the ignition on then off within two seconds 2 The siren will chiro once to confirm auto arming bypass 3 The system will not auto arm note The
28. on Ie Button Silent arm and disarm is controlled by this button Si 3 CLIFFORD ES 3K Button warning Operation of the remote start module if the the vehicle starts in gear is contrary to its intended mode of operation Operating the remote start system under these conditions may result in property damage or personal injury Immediately cease the use of the unit and repair or disconnect the installed remote start module Clifford will not be held responsible or pay for installation or reinstallation costs Remote start is controlled by this button CLIFFORD Button then gf Button Accessory B output is controlled by these buttons CLIFFORD Button then gap Button These buttons activate SmartWindows CLIFFORD Button then XK AK Button Accessory C output is controlled by these buttons CLIFFORD Button twice then gf Q Button These buttons activate remote valet CLIFFORD Button twice then mp Button These buttons disable the sensors CLIFFORD Button three times then A 3 Button These buttons adjust the dual zone shock sensor 2004 directed electronics inc using your system i The buttons used in the instructions in this manual correspond to the standard transmitter configuration If your transmitter has been custom configured the icons on your transmitter buttons may not correspond to the indicated functions arming with transmitter You can activate or arm the system by pre
29. r the system valet PIN code one time valet feature This feature allows the system to be put in valet mode only until the next time the ignition is turned on ON Valet mode will be exited every time the ignition is turned on OFF Valet mode will only be exited by using the valet switch or the remote control 2004 directed electronics inc 37 sensors dual zone shock sensor The digital dual zone shock sensor provides a warning trigger for lighter impacts to the vehicle as well as a full trigger alarm for heavy impacts adjusting the shock sensor CAUTION DO NOT strike the window glass or flat sheet metal panels that can dent easily It is recommended that you only strike the metal pillars between the windows they are structurally sound enough not to dent ONLY strike the pillars using the heel of your hand it is more than sufficient for the sensor to distinguish this as a theft attempt NOTE You MUST exit using the ARM DISARM button after programming to lock in the new settings Read the following instructions thoroughly for a full understanding of how to properly adjust this sensor 1 Disarm system 2 Transmit Channel 15 Press CLIFFORD 3 times then 3K 3K 1 time e The LED will turn on and the siren will chirp 1 time e Primary full trigger zone adjustment has now been entered e Primary zone can now be adjusted Si 38 CLIFFORD ES 3 Adjusting Primary Zone e Press Gm to increase sensitivity
30. rigger sensor zones are bypassed until the system is disarmed This can be performed anytime the system is armed 1 Arm the system 2 Press CLIFFORD twice and then em 3 The lights will flash four times all warn away zones are now bypassed 4 Transmit the sensor bypass channel again The lights will flash four more times the sensor warn away and full trigger zones are now bypassed 6 The sensor zones will reset when disarmed intellistart and smartwindows sensor bypass When the system sees a command to start the vehicle via the Intellistart it bypasses sensors and will continue to bypass these sensors until the remote start shuts down When the system sees a SmartWindows command for up or down operation the unit will automatically bypass all sensors until the win dows complete their operation 2004 directed electronics inc 11 auxiliary channel bypass Alarm sensors will be bypassed while a pulsed or timed auxiliary output channel is active panic mode with smart door locking If you are threatened in or near your vehicle you can attract attention by triggering the system with your transmitter Just press aa for two seconds to enter Panic Mode The siren will sound and the park ing lights will flash for the programmed duration If the ignition is on the doors will lock if the ignition is off the doors will unlock To stop Panic Mode at any time press f Q on the transmitter again disarm valet m
31. s 12 user selectable features panic mode with smart descriptions column two 26 door locking 12 user selectable features disarm valet mode 12 descriptions column three 28 To exit Valet Mode 13 pin programming 30 ie enter or exit Valet Mode 13 remote start 32 one time auto arming bypass14 remote start features 32 2004 directed electronics inc 1 remote start do s and don ts 33 remote start engine shut COW mici ta de oat 34 shortstop mode 35 low temperature battery start 35 retained accessory power 36 diesel compatibility 36 auto immobilization feature 37 auto immobilization sequence 37 one time valet feature 37 SENSOMS eee nada a ects eee 38 dual zone shock sensor 38 glossary of terms 41 security amp convenience expansions 4 43 health check 45 CUEFORD ES what is included OO e Control module and harness e IntelliStart module and harness e Two five button transmitters e Presentation envelope and quick reference card e Two window decal s XHFantenna receiver with harness e Pre wired blue status LED e PlainView 2 Valet switch e 518C neo siren e One remote adjustable dual zone shock sensor with harness Congratulations on the purchase of your state of the art vehicle security s
32. set to their default fac tory setting as indicated in bold lettering Press the arm disarm button of the TX the siren will chirp twice as confirmation panic off on Off The panic feature is not available On The panic feature is available auto start setting off oattery only temp only battery and temp This feature is only available with the IntelliStart option Off The vehicle will not autostart Battery The vehicle will only autostart when the car battery gets low Temperature The vehicle will only autostart at a preset low temperature Battery and temperature The vehicle will autostart with a low car battery or low temperature note Temperature and battery calibration and settings can be made only with the Clifinet Wizard 2004 directed electronics inc 27 user selectable features descriptions column three The features in this column pertain to programming individual trans mitter channels in custom configurations Following is an explanation of the features arm disarm only The remote control channel programmed into this feature will arm dis arm the system only note When programming a new remote control to custom configura tion a channel must first be programmed to this feature before pro gramming the remaining channels accessory a output The transmitter channel programmed into this feature will activate the accessory output accessory b output The transmitter channel programm
33. ssing d a on your trans mitter for one second When the system arms you will hear two short siren sounds or chirps and see the parking lights flash twice The LED will begin to flash steadily If the vehicle s power door locks have been connected to the system the doors will lock While the system is armed the LED status indicator will flash approxi mately once per second showing that the system is actively protecting your vehicle If you hear more than two chirps when arming refer to the Diagnostics section of this guide These extra chirps confirm a mal function autobypass arming without transmitter The security system also can be programmed to arm itself without a transmitter called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system sees you leave the vehicle by opening and closing a door The siren will chirp twice and the lights will flash twice five seconds after the last door has been closed The system is not actu 9 CLIFFORD 29 ally armed at that point The system arms and the doors lock if con nected and programmed for passive locking at 30 seconds but the siren will not chirp The early chirps provide you with a 25 second warn ing prior to arming note If any protected entry point a door or a switchprotected trunk or hood is open the system will not passively arm Additionally each time a protected entry is trig
34. system will revert to normal auto arming when the system sees the ignition on for at least three seconds During auto arming bypass the system will not roll up the windows if SmartWindows is connected and the accessory output will not auto activate when using the remote to arm the system low battery warning When the transmitter battery is low the system will generate a low pitched tone when disarmed multiple event total recall This will report the last eight system triggers 1 Press and hold P of the PlainView 2 Valet switch 2 While still holding P arm and disarm the system then release the button 3 The LED will start to blink to indicate the most recent trigger and proceed down to the eighth trigger If fewer than eight triggers are stored in memory the LED will blink continuous Si 14 CLIFFORD ES ly until the system is armed disarmed using the transmitter or the ignition is turned on For more information please refer to the Table of Zones section of this guide false alarm control technology FACT I Your system offers FACT Il a feature that prevents annoying repetitive trigger sequences due to a faulty sensor or environmental conditions such as thunder jackhammers airport noise etc Here s how it works The alarm triggers three times If the same sensor is triggering the alarm and the first and the third triggers are within 60 minutes of each other FACT will interpret this pattern of triggers as f
35. the date of purchase to the address listed on the card the unit s date code or serial number is defaced missing or altered the unit has been modified or used in a manner contrary to its intended purpose the unit has been damaged by accident unreasonable use neglect improper service installation or other causes not arising out of defects in materials or construction The warranty does not cover damage to the unit caused by installation or removal of the unit Directed in its sole discretion will determine what con stitutes excessive damage and may refuse the return of any unit with excessive damage TO THE MAXIMUM EXTENT ALLOWED BY LAW ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CON NECTION WITH ITS PRODUCTS DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS DIRECTED SECURITY SYSTEMS INCLUDING THIS UNIT ARE DETERRENTS AGAINST POSSIBLE THEFT DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIM ITATION LIABILITY FO
36. ut off If the system remains in Valet Mode the LED will come back on and restart the 1 hour timer the next time the ignition is turned off Si 20 CLIFFORD ES programming i cliffnet wizard installation software programming Cliffnet Wizard provides access to all available system features and some that are not available when manually programming with the Valet switch Cliffnet Wizard is compatible with Microsoft Windows 95 98 2000 ME XP NT so most programming operations can be accomplished by pointing and clicking with a mouse This eliminates the need for programming grids and lengthy programming sequences For a complete guide to system programming using the Cliffnet Wizard refer to the Cliffnet Wizard help menu manual programming instructions Be sure to document changes by taking note of all feature changes made in programming mode To enter the User Selectable Features programming 1 Ignition on Turn the ignition to the run position or start the engine 2 Enter PIN Enter the factory preset PIN code 2 by pressing on the PlainView 2 Valet switch twice then once note If the factory preset PIN has been changed the new PIN must be entered 2004 directed electronics inc 21 Hold Chirp Release After entering the PIN code press and hold EJ until a chirp is heard and the LED turns on then release the button You have now entered the feature selec tion position of the User Selectable Features grid Colum
37. ystem It has been designed to provide years of trouble free operation This system must be installed by an authorized dealer Installation of this product by anyone other than an authorized dealer voids the warranty As verification of authorization all authorized deal ers are provided with preprinted dealer certificates In order to maximize the use of this system please review this owner s guide carefully prior to using your system You can print additional or replacement copies of this owner s guide by accessing the Clifford web site at www clifford com 2004 directed electronics inc 3 system maintenance The system requires no specific maintenance Your transmitter is pow ered by a miniature 3V lithium battery that will last approximately one year under normal use When the battery weakens operating range will be reduced and the system will provide a low battery warning chirp indi cation when disarming your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validat ed if your warranty registration is not returned Make sure you receive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer fcc id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device
Download Pdf Manuals
Related Search