Home

K-1xe Manual - Ayre Acoustics

1. K 1x Preamplifier Owner s Manual Table of Contents Ayre 0 4 ne er a SS a A eS 2 Operation ss ss Ban eo ee ES 3 Phono Stage was a 08 0 0080 E a de Oe 9 Specifications as 44 sw wa war as SE ER ORS 13 Troubles 24 4 28444424 roda 14 Waranty y Gaia a E A AO 16 Ayre Please send in your warranty The Ayre K 1x offers a significant advance in the musical registration card so we can performance of audio preamplifiers The warmth and stay in contact with yon immediacy of a live performance are apparent from the first listening The combination of superb resolution and a natural relaxed quality will draw you into the music time and time again This level of performance has been implemented using the highest level of workmanship and materials Your Ayre K 1x preamplifier will provide a lifetime of musical enjoyment Page 2 Installation and The preamplifier s power supply emits a mild hum field and should be located away from other components Operation The Ayre K 1x is easy to hook up and use The following guidelines will ensure that the installation goes smoothly Location The Ayre K 1x comprises two components the main preamplifier and the external power supply which are joined by an umbilical cable A detachable connector allows these units to be temporarily separated for easy installation The main unit produces very little heat and can normally be stacked with other components However in certain
2. Revision 1 3 Ayre Acoustics Incorporated 2300 B Central Avenue Boulder Colorado 80301 303 442 7300 www ayre com
3. situations hum can be induced into the audio circuitry In this case try separating the components by a few feet one meter or so to isolate the interfering component The receiver for the optional infrared remote control is mounted behind the left most scallop on the preamplifier s front panel Although the transmitter s beam will reflect off of most wall surfaces a direct line of sight from the listening position will ensure the maximum range The beam will also travel through glass if necessaty Page 3 Inputs When you have a choice a The Ayre K 1x offers three pairs of balanced inputs and balanced connection will offer three pairs of unbalanced inputs Balanced connections are slightly higher sound quality made via three pin XLR connectors while unbalanced than an unbalanced connections are made via RCA jacks In accordance with the connection IEC standard XLR pin 2 is the positive phase hot The input connectors on the rear panel are labeled 1 through 6 If you are connecting a tape deck to your Y system be sure to connect it to input 6 This will prevent the undesired possibility of a feedback loop when monitoring a tape recording If a tape deck is not installed in your system input 6 performs like the other unbalanced inputs 1 If the optional phono stage is installed it will y use input 2 Do not connect a high level source to the phono input If the phono stage is not ins
4. Ayre and is in lieu of all other warranties All implied warranties including warranties of merchantability or fitness for any particular purpose shall be strictly limited in duration to five years from the date of original purchase and upon expiration of the warranty period five years Ayre shall have no further obligation of any kind whether express or implied Further Ayre shall in no event be obligated for any incidental or consequential damages as a result of any defect or any warranty claim whether express or implied Some states do not allow exclusion or limitations of incidental or consequential damages or limitations on how long implied warranties last so the above limitation and exclusions may not apply to you Page 17 Page 18 6 Ayre does not authorize any third party including any dealer or sales representative to assume any liability of Ayre or make any warranty for Ayre The unit must not have been altered or improperly serviced The serial number on the unit must not have been altered or removed 7 Warranty registration cards must be completed and mailed to Ayre within 30 days of purchase Ayre may at its option require from the purchaser valid proof of purchase dated copy or photocopy of dealer s original invoice 8 If this product is used in a commercial or industrial application then special warranty exclusions may apply Contact Ayre for commercial warranty policies A Place for Notes Page 19
5. Ayre warrants the materials and workmanship of this product for a period of five years from date of first purchase If any defects are found in the materials or workmanship of this Ayre product within the warranty period the unit will be repaired or replaced by Ayre or its authorized agent 2 Purchaser must return the product packed in the original shipping carton freight prepaid to Ayre Acoustics Inc 2300 B Central Avenue Boulder Colorado 80301 3 Ayre reserves the right to inspect any product that is the subject of any warranty claim prior to repairing or replacing it Final determination of warranty coverage lies solely with Ayre Out of warranty claims will be billed for labor materials return freight and insurance as required Any product for which a warranty claim is accepted will be returned to the purchaser and the cost of shipping and insurance will be factory prepaid within the boundaries of the USA Units to be shipped outside of the USA will be shipped freight collect only This warranty gives specific legal rights The purchaser also has implied warranty rights and may also have other rights which vary from state to state A Ayre strives to manufacture the finest possible equipment and therefore reserves the right to make improvements on its products without necessarily assuming an obligation to retrofit such changes upon its previously manufactured models 5 The above warranty is the sole warranty given by
6. R connectors at the preamplifier end and the appropriate connector RCA or DIN depending on the particular installation at the turntable end This is the preferred solution and offers the highest level of sound quality Page 9 It is recommended that the loading not be changed from 50 RO when using a moving magnet cartridge Page 10 Ayre manufactures both adapters and dedicated cables These high performance custom designs are available from your authorized Ayre dealer In addition termination instructions are available if you wish to reterminate your current cables Please contact the factory for further details Gain and Loading The gain of the phono stage is set at the factory to 50 dB which is well suited to most modern phono cartridges In addition the gain is adjustable in 10 dB steps from 40 dB to 60 dB accommodating virtually any cartridge made Recommended gain settings are as follows Cartridge Output Phono Gain Gain Resistor Less than 1 0mV e a RN 100 LOV to SM 22 DA 750 Greater than 3 0 mV 40dB 2490 These are guidelines only Variations from these settings are perfectly acceptable The default cartridge load is 50 kQ which is suitable for almost all cartridges However many moving coil cartridges yield better performance if they are loaded with a lower impedance Usually a lower load impedance results in a more focused soundstage with greater image solidity and less apparent dist
7. allen wrench supplied Small screwdriver 0 080 to 0 100 2 0 to 2 5 mm Tweezers or small needle nose pliers is comparable in complexity to installing a phono cartridge Do not perform this task yourself unless you are completely comfortable with it Y Changing the phono gain and loading resistors e Page 11 Page 12 Disconnect the preamplifier s power supply e from the AC power before working on the unit To adjust the gain or loading of the phono stage use the supplied 5 64 allen wrench to remove the six screws that secure the top cover The two phono boards one per channel are mounted vertically on the right and left sides of the chassis Each phono board has two small brown terminal strips used to connect small metal film resistors The terminal strip towards the rear of the preamplifier is used to adjust the gain of the phono stage while the terminal strip towards the front of the unit accepts the loading resis tor The resistor leads are clamped by the two screws in the terminal strip forming a gas tight connection for optimum sound quality To remove the installed resistors use a small flat bladed screwdriver to loosen the two screws in the terminal strip until the screw heads are flush with the top surface of the terminal strip Gently remove the resistor with a pair of tweezers or small needle nose pliers To install the new resistors use the tweezers or small needle nose pliers to insert the two leads in
8. ge can be increased 6 dB to compensate for this loss Please contact your authorized Ayre dealer or the factory for information on this procedure It is not recommended to increase the gain of the Ayre K 1x when using a balanced amplifier as the level of the lowest volume setting may be too loud Break In Please note that the optional A break in period is required to achieve the maximum sonic phono stage utilizes potential of the Ayre K 1x due to the manufacturing additional circuitry and will processes used in the capacitors circuit board material and require its own break in wires This normally requires between 100 and 500 hours of period playing time Page 8 Phono Stage The optional phono stage in the Ayre K 1x offers the ultimate in flexibility and performance for all types of phono cartridges Connections As the phono cartridge is an inherently balanced device the phono stage is also balanced using XLR jacks at the input This configuration yields maximum sonic performance with minimum noise and hum Since most tone arms and or turntables are not equipped with XLR connectors there are two choices for making the proper connection 1 Use an RCA to XLR adapter This often may be the easiest solution to implement but introduces an extra set of contacts into the signal path In addition this converts the balanced input into an unbalanced input and causes a slight loss of sound quality 2 Use dedicated cables with XL
9. ifier with balanced inputs unity gain occurs when the volume control is 10 steps below the maximum setting see illustration The tape record selector Record controls which source component is connected to the tape output jacks It is recommended that the tape record selector be switched to the Off position except when making a recording This will isolate the tape deck s circuitry from the preamplifier providing the highest level of sound quality when listening Remote Control The optional remote control for the Ayre K 1x has four buttons The top two buttons on the right side control the volume level while the bottom button on the right side toggles the preamplifier s mute control The single button on the left side of the hand held transmitter will operate an Ayre V 1x power amplifier Page 7 Unbalanced Power Amplifiers When using the Ayre K 1x Unbalanced power amplifiers with single ended inputs only with an unbalanced power utilize one half of the Ayre K 1x s balanced output signal amplifier note tha t the The result is a 6 dB gain reduction requiring that the unity gain volume setting will volume control be further advanced for an equivalent now occur when the volume listening level However certain systems may have control is five steps below the insufficient gain to produce a satisfying listening level even maximum setting with the volume control turned fully up If required the gain of the line sta
10. king AC outlet 2 Check the AC line fuse To check the fuse locate the rectangular fuse holder mounted on the rear panel of the power supply Press downwards on the top edge then pull outward There are two fuses mounted in the fuse holder The inner one is the operating fuse and the outer one is a spare Always use the correct fuse The condition of the fuse can be determined by a visual inspection although an ohm meter provides a more reliable method If in doubt substitute the spare for the operating fuse If the spare fuse also blows do not attempt further repairs Line Voltage Fuse Rating Time Delay VOOM en nen ee LA 120NV oe s LA POON a re LA There are no user serviceable parts in the Ayre K 1x If the preamplifier still does not operate bring the unit to your dealer for assistance Do not remove the power supply cover Hazardous voltages may exist inside the unit Page 15 Statement of Warranty Please take the time to fill out and return the enclosed warranty registration card Your Ayre K 1x preamplifier is warranted against defects in workmanship and materials for a period of five years from the date of purchase This warranty is transferable to subsequent purchasers within the original five year period All warranty claims must be made through an authorized Ayre dealer or distributor A complete statement of warranty is given below Warranty Statement Page 16 1 Ayre Acoustics Inc
11. ortion A higher load impedance will give a more open sound with greater air and life The final value must be chosen by ear to give the best sound in your particular system Phono Gain Resistor Cartridge Loading c201 c202 o gt L o a a A Ral 0405 E OSS 8 Y 2 od lt a e o o 3 8 8 3 S gt a ES T g gt 02058 32 D Bc E o C 8 0 9 UR4O1 eso S a o 2 5 csoo O a o o oso o 040 8 o J O x z gt 2 te 3 CEL O LDK DO LDL 2 s E ops amp Saat g SB ma CIEN aC El SS 8 8 8 Ss 8 Hal IS a 3 yl 5 z s 2 2a 5 hos S ss is gt 3 El 8 eo o oA 8 S BE o E El 8 vo o edo eo o os m o a QUES B SR la raS o E ON a 2 g oo e 3 E ORBo Bo Sota Bo Bo 8 gE mB 8304 E 3 fa N 0 5 ENS O 270 ES w E ERO OK TI I C a A 3 a o e z 4 8 8 e 6 gt q OS S gt o S O o S UR402 ES 42078 N 8 8 a 4 a 2 B lj Sg ad u z 3 80 3 URSDO SL i ES 3 5 Q 9500 0314 0406 gt 0210 203 2204 caos c304 The phono gain and loading can be adjusted by your authorized Ayre dealer However for those owners that prefer to perform this task themselves the following tools are required 5 64
12. rared Remote Unity Gain Input 1 Control Receiver Tuner Phono Disk Listen Video Auxil Off Tape 3 0 dB Steps 4 0 dB Steps 2 0 dB Steps Input 6 Status Indicator Red Warm Up Green Mute Blue Listen Page 5 The Ayre K 1x draws very little power and is designed to be left on at all times The volume control and the mute switch may be operated either by the optional remote Page 6 control or the front panel controls Powering the Unit Be sure to connect the umbilical cable to the power supply before plugging in the AC power Install or remove the umbilical connector only y when the AC power is disconnected The Ayre K 1x features a sophisticated power monitoring system When first plugged in to an AC power source the front panel indicator light will glow red for approximately 90 seconds During this time the outputs are muted and the mute switch is inoperable After the circuitry has stabilized the indicator light will change to green indicating that the unit is ready for play though the unit remains muted When the listener toggles the mute control the unit is operational and the indicator light glows blue Should the AC line lose power the preamplifier s outputs are immediately muted Similarly if the AC line voltage drops below 80 of normal brown out the outputs will mute and the indicator light will glow red After the line voltage returns to normal the initial power up c
13. talled input 2 performs like the other balanced inputs Please refer to the section Optimizing the Phono Stage for more detailed information on connecting your turntable Input Labels Input 1 on the rear panel The front panel switches can be labeled to reflect the corresponds to the top label components in your individual system The faceplate must while input 6 corresponds to be removed to install custom labels for the selector switches the bottom label Use the supplied 1 8 allen wrench to remove the four screws visible on the faceplate Then slide the faceplate away from the unit taking care not to scratch the knobs Page 4 AU three pairs of outputs may be used simultaneously if 2 0 dB Steps desired 1 0 dB Steps Remove the old label by using a small object such as an allen wrench to push through the access holes on the rear of the faceplate The labels have a self adhesive backing and new ones are simply pressed into place Outputs The Ayre K 1x offers two pairs of balanced outputs and one pair of unbalanced outputs Please note that the unbalanced outputs invert o absolute polarity When using an unbalanced connection between the Ayre K 1x and your power amplifier it is suggested that the speaker cables plus and minus leads be reversed at the amplifier This will restore absolute polarity and can enhance the sense of realism on many recordings Inf
14. to the holes on the side of the terminal strip Orientation is not important the resistor can be installed either way Use the flat bladed screwdriver to gently snug the two screws down Do not overtighten them Do not operate the preamplifier without the gain adjusting resistors installed Replace the top cover reinstalling the six screws with the 5 64 allen wrench Specifications Gain Line Gain Phono Input Impedance Line Input Impedance Phono Output Impedance Power Consumption Dimensions Weight 16 dB to balanced outputs 10 dB to unbalanced outputs Adjustable 40 dB 50 dB factory setting 60 dB 10 kQ each phase Adjustable 50 kQ factory setting 100 Q 249 Q 499 Q 1000 Q loading resistors supplied Other values available upon request 300 Q each phase 30 watts 18 W x 11 Dx5 1 2 H 46cm x 28cm x 14cm Main Unit 13 W x 8 Dx3 H 33cm x 20 3cm x 7 6cm Power Supply 45 pounds 20 kg Page 13 Symptom Remote control not working Symptom No sound even though status indicator is glowing blue Symptom Status indicator lamp not lit Page 14 Trouble Should the Ayre K 1x preamplifier ever fail to operate properly please check the following Check the condition of the batteries 2 x AAA located in the remote control Check all connections on the rear panel to make sure they are secure 1 Be sure that the power supply unit is connected to a wor
15. ycle will begin again Controls There are four controls on the Ayre K 1x preamplifer the volume control the input selector Listen the tape record selector Record and the mute switch These controls provide the ideal combination of flexibility and ease of use It is normal to listen with the volume knob advanced farther than you may be used to with other equipment Since the tape record selector Record is controlled separately from the main input selector Listen it s possible to listen to one source while recording from another Please note that the supplied batteries 2 x AAA must be installed in the remote control unit prior to use Unlike other products that use conventional volume controls potentiometers the Ayre K 1x uses a mil spec precision stepped attenuator with solid silver contacts to provide the ultimate in sound quality This volume control features 46 distinct positions offering precise and repeatable settings The volume control offers 1 0 dB steps over most of its range allowing you to exactly select the desired listening level To maximize its capabilities it has been designed so that the volume knob will be between 1 o clock and 3 o clock for a loud playback level in most systems When a surround sound processor is used it is sometimes useful to know the unity gain volume setting Since the gain of the Ayre K 1x line stage is 16 dB when driving a power ampl

K-1xe Manual - Ayre Acoustics

Contents

Download Pdf Manuals

Related Search

Related Contents