Home

Intel® Desktop Board DQ965GF Product Guide

Contents

1. 0M19388 Figure 18 Installing a PCI Express x16 Card 40 Installing and Replacing Desktop Board Components Removing the PCI Express x16 Card Follow these instructions to remove the PCI Express x16 card from the connector 1 2 Observe the precautions in Before You Begin on page 27 Remove the screw Figure 19 A that secures the card s metal bracket to the chassis back panel Push down on the card ejector lever Figure 19 B to release the card from the connector C Pull the card straight up 0M19389 Figure 19 Removing a PCI Express x16 Card 41 Intel Desktop Board DO965GF Product Guide Connecting the IDE Cable 42 The IDE cable can connect two drives to the desktop board The cable supports the ATA 66 100 transfer protocol Figure 20 shows the correct installation of the cable NOTES ATA 66 100 compatible cables are backward compatible with drives using slower IDE transfer protocols If an ATA 66 100 disk drive and a disk drive using any other IDE transfer protocol are attached to the same cable the maximum transfer rate between the drives may be reduced to that of the slowest drive Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master device For example do not connect an ATA hard drive as a slave to an ATAPI CD ROM drive For correct function of the cable Observe the precautions in Before You Begin on page 27 e Attach the cable end with the sin
2. 62 Updating the BIOS with Iflash qa kupa iha 63 Recovering the BIOS uuu e iii e EU RA NAP RA aqa ll I RAA RITE 64 4 Configuring for RAID Intel Matrix Storage Technology Configuring the BIOS for Intel Matrix Storage Technology 65 SATA Port Mapping i see eee ense aate e e Rer ex EVAN e Fo ER ED EO E X OA 65 Creating Your RAID Set eter ete ka eh kri pe rere ra drei pe te quwaq kasq 66 Loading the Intel Matrix Storage Technology RAID Drivers and Software 67 Setting Up a RAID Ready System 6000 menses nnn nnn 67 vi Contents A Error Messages and Indicators BIOS Beep Codes Mala ak ama Mepa oped ia epi vue xr ena ana akal azmin ele iie e TRE E ekg 69 BIOS Error Messages a A A REE EAD EE 69 B Regulatory Compliance 71 Safety Regulations een anre tie ee inte next e ede i ner d ael galeri Ll de Kala 71 Place Battery Makin Gs saya a ae n Earn eee xa e i a d e NL I ca RR i o a Ue 71 European Union Declaration of Conformity Gtatement GG 72 Product Ecology Statements use Naia rere x edd Re la Re E C e FE RR nn 73 Lead Free Desktop Board uror ro d AA OR E Ada 76 EMCRegulations eiit ay lar sila iza sea a Dn aba kalas akkale ea EE e 77 Ensure Electromagnetic Compatibility EMC Compliance eere 78 Product GEES EI IS ii A e e id tent alen EE 79 Board Level Certification Markings r neta
3. Intel Desktop Board DO965GF Product Guide A VORSICHT 56 Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr Die Batterie darf nur durch denselben oder einen entsprechenden vom Hersteller empfohlenen Batterietyp ersetzt werden Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore Per disfarsi delle pile usate seguire le istruzioni del produttore PRECAUCION Existe peligro de explosi n si la pila no se cambia de forma adecuada Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo Para deshacerse de las pilas usadas siga igualmente las instrucciones del fabricante WAARSCHUWING Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij Batterijen moeten zoveel mogelijk worden gerecycled Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving ATEN O Haver risco de explos o se a bateria for substitu da por um tipo de bateria incorreto As baterias devem ser recicladas nos locais apropriados A elimina o de baterias usadas deve ser feita de acordo com as regulamenta es ambientais da regi o ASCIAROZZNAS IcHye pbi3bika Bbl6yxy Kani 3aMeHeHbl AKYMY IATap HenpaBinbHara
4. Once additional SATA drives have been added open the Intel Matrix Storage Technology Console Software and follow the directions to update to a RAID setup 67 Intel Desktop Board DO965GF Product Guide 68 A Error Messages and Indicators Desktop Board DO965GF reports POST errors in two ways e By sounding a beep code e By displaying an error message on the monitor BIOS Beep Codes The BIOS also issues a beep code one long tone followed by two short tones during POST if the video configuration fails a faulty video card or no card installed or if an external ROM module does not properly checksum to zero Table 13 lists the BIOS codes Table 13 Beep Codes Beep Description 3 No memory Siren Processor overheat on reboot BIOS Error Messages When a recoverable error occurs during the POST the BIOS displays an error message describing the problem Table 14 gives an explanation of the BIOS error messages Table 14 BIOS Error Messages Error Message PROCESSOR THERMAL TRIP ERROR MULTI BIT ECC ERROR SINGLE BIT ECC ERROR CMOS BATTERY ERROR CMOS CHECKSUM ERROR CMOS TIMER ERROR MEMORY SIZE DECREASE ERROR INTRUDER DETECTION ERROR SPD TOLER ERROR MEM OPTIMAL ERROR Explanation Processor was previously shutdown due to a thermal event overheating The firmware has detected that a Multi Bit ECC Error occurred The firmware has detected that a Single Bit ECC Error occurred The firmware has detected
5. and selecting Product Documentation from the left hand menu http support intel com support motherboards deskto Desktop Board Features Wake from USB NOTE NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB USB bus activity wakes the computer from an ACPI S3 state Wake from PS 2 Keyboard Mouse PS 2 keyboard mouse activity wakes the computer from an ACPI S3 state PME Signal Wake up Support When the PME signal on the PCI bus is asserted the computer wakes from an ACPI S3 S4 or S5 state WAKEZ Signal Wake up Support When the WAKE signal on the PCI Express bus is asserted the computer wakes from an ACPI S2 S3 S4 or S5 state Speaker A speaker is mounted on the desktop board The speaker provides audible error code beep code information during the Power On Self Test POST Battery A battery on the desktop board keeps the values in CMOS RAM and the clock current when the computer is turned off Go to page 55 for instructions on how to replace the battery Real Time Clock The desktop board has a time of day clock and 100 year calendar The battery on the desktop board keeps the clock current when the computer is turned off 25 Intel Desktop Board DO965GF Product Guide 26 2 Installing and Replacing Desktop Board Components This chapter tells you how to e Install the I O shield Install and remove the desktop board e Install and remove a process
6. High Definition Audio interface Advanced jack sense for the back panel connectors that enables the audio codec to recognize the device that is connected to an audio port and retask the connector via the audio driver S N signal to noise ratio 95 dB Microphone input supporting Stereo microphone Microphone boost The subsystem includes the following connectors Front panel audio connector including functionality for Line out Microphone in Back panel audio connectors that are configurable through the audio device drivers Line in retasking jack Line out retasking jack Mic in retasking jack Related Links Go to the following link or pages for more information about Audio drivers and utilities http support intel com support motherboards deskto Installing the front panel audio solution page 45 The location of audio connectors Figure 23 on page 48 Input Output I O Controller The super I O controller features the following 16 One serial port header One parallel port with Extended Capabilities Port ECP and Enhanced Parallel Port EPP support Serial IRQ interface compatible with serialized IRQ support for PCI systems PS 2 style mouse and keyboard interfaces Interface for one 1 2 MB or 1 44 MB diskette drive Intelligent power management including a programmable wake up event interface PCI power management support Desktop Board Features LAN Subsystem The LAN subsystem
7. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user s authority to operate the equipment Tested to comply with FCC standards for home or office use Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil numerique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe B prescrites dans le R glement sur le broullage radio lectrique dict par le minist re des Communications du Canada Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY TH
8. and ICH8 plus an onboard remote sensor e Thermally monitored closed loop fan control for all onboard fans that can adjust fan speed or switch the fans off as needed Chassis Intrusion Detection The board supports a chassis security feature that detects if the chassis cover has been removed The security feature uses a mechanical switch on the chassis that can be connected to the chassis intrusion header on the desktop board See Figure 26 on page 51 for the location of the chassis intrusion header 21 Intel Desktop Board DO965GF Product Guide Power Management Features Power management is implemented at several levels including ACPI Software support through the Advanced Configuration and Power Interface ACPI Hardware support Power connectors Fan headers LAN wake capabilities Instantly Available PC technology Suspend to RAM 5 V standby power indicator LED Wake from USB Wake from PS 2 keyboard mouse Power Management Event signal PME wakeup support WAKE signal wake up support ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer The use of ACPI with the desktop board requires an operating system that provides full ACPI support Power Connectors ATX12V compliant power supplies can turn off the computer power through system control When an ACPI enabled computer receives the correct command the power supply r
9. Memory Configuration Before installing DIMMs read and follow these guidelines for dual channel configuration NOTE The Intel Management Engine in the chipset requires memory to be populated in Channel A DIMM 0 in order for it to enable Intel Quiet System Technology and Intel Active Management Technology 35 Intel Desktop Board DO965GF Product Guide Two or Four DIMMs Install a matched pair of DIMMs equal in speed and size see Figure 13 in DIMM 0 blue of both channels A and B DIMM 0 DIMM 1 Channel A DIMM 0 h DIMM 1 Channel B 9 OM19403 Figure 13 Dual Channel Memory Configuration Example 1 If additional memory is to be used install another matched pair of DIMMs in DIMM 1 black in both channels A and B see Figure 14 DIMM 0 DIMM 1 Channel A DIMM 0 h DIMM 1 Channel B SBBESBBEEBEE OM19404 Figure 14 Dual Channel Memory Configuration Example 2 36 Installing and Replacing Desktop Board Components Three DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 blue and DIMM 1 black of channel A Install a DIMM egual in speed and total size of the DIMMs installed in channel A in either DIMM 0 or DIMM 1 of channel B see Figure 15 iir Channel A DIMM 1 ENS Channel B DIMM 1 OM19405 Figure 15 Dual Channel Memory Configuration Example 3 NOTE All other memory configurations will result in single channel memory operation Installing DIMMs To make sure yo
10. TbITTy AkymynaTapb NaBiHHbl Ma MarubiMacui nepenpayoysBayya Maz6aynauya ag CTapbix akymynsaTapay narp36Ha 3rogHa 3 MACLJOBbIM 3aKaHagayCTBaM na 3Kanorii UPOZORN N V p pad v m ny baterie za nespr vn druh m ze doj t k v buchu Je li to mo n baterie by m ly b t recyklov ny Baterie je t eba zlikvidovat v souladu s m stn mi p edpisy o ivotn m prost ed 1pocoyn Yndpxel kiv uvoc yia Ekpn n de nepirnroor nou n unarap a avrikaraora si ano uia AavBaguevou TUnou Ol unatapiec Ba np riei va avakukAQvovrai rav KdTI TETOIO Elva OuvaTo H an ppiwn rov xprjoiuonori u vov unarapiov np nel va yiverai OULPWVA HE TOU kar T NO ngpiBaAAovrikoUG KGVOVIOLIOUG Installing and Replacing Desktop Board Components A VIGYAZAT Ha a telepet nem a megfelel t pus telepre cser li az felrobbanhat A telepeket lehet s g szerint Ujra kell hasznos tani A haszn lt telepeket a helyi k rnyezetv delmi el r soknak megfelel en kell kiselejtezni N as REDD BEM OC REDEBIDUEF VT Y L ASA RE hb Ek CINE BEV 2 JkEL C lt J amp LX PAROS HERES ORTIK Hi olim ES C lt CSL A AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul Bateri sepatutnya dikitar semula jika boleh Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan A OSTRZEZENIE Istnieje niebezpiecze stwo wybuchu w przypadku zastosowania niew a ciwego typu baterii Zu yte baterie n
11. The SATA port mapping shown in Figure 31 is consistent with the SATA port assignment in the Intel Matrix Storage Configuration Utility Ctrl I and the Intel Matrix Storage Console software Creating Your RAID Set 1 Upon re boot you will see the following Intel Matrix Storage Manager option ROM status message on the screen Press Ctrl I to enter the RAID Configuration Utility Press lt Ctrl I gt and enter the RAID Configuration Utility In the Intel Matrix Storage Manager option ROM Main Menu select option 1 Create RAID Volume Enter a volume name and press Enter NOTE The RAID Volume name must be in English alphanumeric ASCII characters Use the arrow keys to select RAID 0 or RAID 1 if only two SATA drives are available RAID 5 and RAID 10 these options will only appear if three or four SATA drives are installed respectively Press Enter once you have selected the RAID LEVEL NOTE The maximum number of SATA drives configurable for a single RAID array is four However you can create more than one RAID array on a single system Select the drives to be used in the RAID array only if there are more than two drives available and press Enter Select the strip size if necessary and press Enter Enter the size of the volume if you enter less than the maximum volume size you can then create a second RAID array on the remaining portion of your volume and press Enter Finally press Enter to
12. and I O space for that add in card You do not need to run the BIOS Setup program after you install a PCI PCI Express add in card Security Passwords The BIOS includes security features that restrict whether the BIOS Setup program can be accessed and who can boot the computer A supervisor password and a user password can be set for the BIOS Setup and for booting the computer with the following restrictions The supervisor password gives unrestricted access to view and change all Setup options If only the supervisor password is set pressing Enter at the password prompt of Setup gives the user restricted access to Setup e If both the supervisor and user passwords are set you must enter either the supervisor password or the user password to access Setup Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered e Setting a user password restricts who can boot the computer The password prompt is displayed before the computer is booted If only the supervisor password is set the computer boots without asking for a password If both passwords are set you can enter either password to boot the computer Related Links 20 For instructions on resetting the password see Clearing Passwords on page 53 Desktop Board Features Trusted Platform Module TPM The TPM 1 2 component is designed to enhance platform security above and beyond the capabilities of today s s
13. be used Since the 3 pin fan cannot use the onboard fan control the fan will always operate at full speed OM19407 Figure 12 Connecting the Processor Fan Heat Sink Cable to the Processor Fan Header 34 Installing and Replacing Desktop Board Components Removing the Processor For instructions on how to remove the processor fan heat sink and processor refer to the processor installation manual or the Intel World Wide Web site at Integration of the Boxed Intel Pentium 4 Processor in the 775 Land Package Installing and Removing Memory AN CAUTION When connected to AC power the memory slots on the board will be powered and in use A red LED located near the memory slots will be lit if the memory slots are powered Installing or removing memory from the board while the memory slots are powered may result in damage to both memory and board Before installing or removing memory disconnect the system from AC power and wait for the LED to go off before proceeding NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board requires DIMMs that support the Serial Presence Detect SPD data structure You can access the PC Serial Presence Detect Specification at http www intel com technology memory ddr specs dda18c32 64 128x72ag a pdf Desktop Board DQ965GF has four 240 pin DDR2 DIMM sockets arranged as DIMM 0 and DIMM 1 in both Channel A and Channel B Guidelines for Dual Channel
14. nena eta naes 79 Chassis and Component Certifications ala 80 Figures 1 Desktop Board DQ965GF Componente aaa aaa nnn nnn 11 2 LAN Connector LEDS ee ete ox de ex ex mee rede onde ee ode ond RR de 17 3 Location of the On board Power Indicetors Gaal 24 4 Installinggthel O0Shield na 29 5 Desktop Board DQ965GF Mounting ScrewHolelocations 30 6 Lift Socket LEME it eae cee AY dace eave AE EEE K EYE EEE il 31 La Lift the Load Plate isis u Se Eten erm Ee EA NN IRE eis 31 8 Remove the Protective SocketCover na 32 9 Remove the Processor from the Protective ProcessorCover 32 10 InstalltheProcessor GG 33 O the Load Plate oen en E ait tiv ane Bk e KA EG 33 12 Connecting the Processor Fan Heat Sink Cable to the Processor Fan Header 34 13 Dual Channel Memory Configuration Example 1 sse 36 14 Dual Channel Memory Configuration Example2 G nnnm 36 15 Dual Channel Memory Configuration Example3 G n 37 16 Use DDR2 DIMMS rex NENNEN ed SEENEN NEEN NENNEN le D 37 17 Installing a EICH 38 18 InstallingaPclExpressx16Card 111 e ened 40 19 RemovingaPClExpressx16Card AANEEN NaN 41 20 Connecting the IDE Cable evre tr ae dE asha acts ola eda da e i mal 42 2
15. page 27 Turn off all peripheral devices connected to the computer Turn off the computer Remove the AC power cord from the computer Remove the computer s cover Gently spread the retaining clips at each end of the DIMM socket The DIMM pops out of the socket Hold the DIMM by the edges lift it away from the socket and store it in an anti static package Reinstall and reconnect any parts you removed or disconnected to reach the DIMM Sockets Replace the computer s cover and reconnect the AC power cord 39 Intel Desktop Board DO965GF Product Guide Installingand Removing a PCI Express x16 Card A CAUTION When installing a PCI Express x16 card on the desktop board ensure that the card is fully seated in the PCI Express x16 connector before you power on the system If the card is not fully seated in the PCI Express connector an electrical short may result across the PCI Express connector pins Depending on the over current protection of the power supply certain desktop board components and or traces may be damaged Installing a PCI Express x16 Card 1 Observe the precautions in Before You Begin on page 27 2 Place the card in the PCI Express x16 connector Figure 18 A and press down on the card until it is completely seated in the connector and the card retention notch snaps into place around the retention mechanism pin 3 Secure the card s metal bracket to the chassis back panel with a screw Figure 18 B B
16. panel audio jacks will need to be manually configured for microphone or line out functionality in the Intel Audio Studio application Table 5 AC 97 Audio Header Signal Names Pin Signal Name i Signal Name 1 AUD GND 3 MIC BIAS AUD GND 5 FP OUT R FP RETURN R 7 KEY 9 FP OUT L FP RETURN L 5 Connect the audio cable to the front panel audio solution 6 Replace the cover 45 Intel Desktop Board DO965GF Product Guide To restore back panel audio follow these steps 1 Observe the precautions in Before You Begin on page 27 2 Turn off all peripheral devices connected to the computer Turn off the computer and disconnect the AC power cord 3 Remove the cover 4 Remove the front panel audio cable 5 Replace the cover Connecting to the USB 2 0 Headers Before connecting to the USB 2 0 headers observe the precautions in Before You Begin on page 27 See Figure 22 G on page 44 for the location of the black USB 2 0 header Table 6 shows the pin assignments for each USB 2 0 header Table 6 USB 2 0 Header Signal Names USB Port A USB Port B Pin Signal Name Pin Signal Name 1 POWER 2 POWER 3 D 4 D 5 D 6 D 7 GND 8 GND 9 KEY 10 NO CONNECT Note USB ports may be assigned as needed Connecting to the Front Panel Header 46 Before connecting to the front panel header observe the precautions in Before You Begin on page 27 See Figure 22 F on page 44 for the location of the multi colored fr
17. reciclados de maneira adequada Consulte o site http www intel com intel other ehs product ecology Recycling Program htm em Ingl s para obter os detalhes sobre este programa inclusive o escopo dos produtos cobertos os locais dispon veis as instru es de envio os termos e condi es etc Russian B kauecrBe yac M cBoux o683arenbcrB K OKpyxatouje cpege B Intel co3gaHa nporpaMMa yTunu3zaunu npoaykuna Intel Product Recycling Program Ana npenocraB ieHA4s KOHeUHBIM MONb30BaTeNAM Mapok npoaykyunn Intel BO3MOXHOCTM BO3BpaTa UCNONb3YeEMON npoaykunaMa B CNeynanu3supoBaHHble NYHKTbI ANA AONXKHO yrAnM3auM Moxany cta o6parurecb Ha Be6 calr http www intel com intel other ehs product ecology Recycling Program htm 3a uH bopMauue o6 To nporpaMMe MpuHUMaembIx MpoAyKTaX Mecrax Npuema UHCTpyKUMAX o6 ornpaBke NONOKEHUAX N YCNOBNAX M T A T rkce Intel evre sorumlulu una ba ml l n n bir par as olarak perakende t keticilerin Intel markal kullan lm r nlerini belirlenmi merkezlere iade edip uygun ekilde geri d n t rmesini ama layan Intel r nleri Geri D n m Program n uygulamaya koymu tur Bu program n r n kapsam r n iade merkezleri nakliye talimatlar kay tlar ve artlar v s dahil b t n ayr nt lar n grenmek i in l tfen http www intel com intel other ehs product ecology Recycling Program htm web sayfas na gidin 75 Intel Desktop Board
18. that a CMOS battery failure occurred The firmware has detected that a CMOS Checksum Error occurred The firmware has detected that the system date time has not been set The firmware has detected that the system memory has decreased The system chassis was opened SERIAL PRESENCE DETECT SPD device data missing or inconclusive Properly programmed SPD device data is required for reliable operation DDR2 533 MHz memory assumed at slowest timings The installed amount of memory in Channel A is not equal to the amount of memory in Channel B Maximum memory performance is achieved with equal amounts of memory installed in each channel 69 Intel Desktop Board DO965GF Product Guide 70 B Regulatory Compliance This appendix contains the following regulatory compliance information for Desktop Board DO965GF e Safety regulations e European Union Declaration of Conformity statement e Product Ecology statements e Electromagnetic Compatibility EMC regulations e Product certifications Safety Regulations Desktop Board DQ965GF complies with the safety regulations stated in Table 15 when correctly installed in a compatible host system Table 15 Safety Regulations Regulation Title UL 60950 1 2003 Information Technology Equipment Safety Part 1 General CSA C22 2 No 60950 1 03 Requirements USA and Canada EN 60950 1 2002 Information Technology Equipment Safety Part 1 General Requirements European Union I
19. 1 Connecting the Serial ATA Cable nsnm memes ene 43 22 Internal Headers sivil ki KEL NNN NEE NENNEN N E ve ee Re P E a EE 44 23 Back Panel Audio Connectors na 48 24 Location of Chassis Fan Headers na 49 25 Connecting Power Supply Cables GG nennen nnn nnn 50 26 Location of Other ConnectorsandHeaders G GG 51 27 LocationoftheBIOSConfigurationlumperBlock 52 28 Back Panel Connectors EAR RR M E 54 29 Removing the Battery iii er xe ean n ex t ddl i Rade da o De 59 30 Original SATA Port Mapping for DesktopBoardD0965GHF 65 31 SATA Port Mapping for Desktop Board DQ965GF After RAID is Enabled 66 vii Intel Desktop Board DO965GF Product Guide Tables s Feature SUumprafYu 2 2 A mila ami e me yla eza akdi la ERI RP ERE lak 9 2 Desktop Board DQ965GF Componente aaa 12 3 LAN Connector EED States 3 eset eo e AANER A a ka 17 4 Front Panel Audio Header Signal Names for Intel High Definition Audio 45 5 AC 97 Audio Header Signal Names eee e eee eee eee ea a eee nena ees 45 6 USB2 0HeaderSignalNames la 46 Za Eront Panel Header u sitet eri dea e Mi elan lala a 46 8 AlternateFrontPanelPowerLEDHeader 47 9 IEEE1394aHeaderSignalNames 1 47 10 Serial Port Header Signal Names ssssssssses
20. 965GF Components Label Description HD Audio Link header PCI bus connector 2 Front panel audio header PCI bus connector 1 PCI Express x1 connector PCI Express x16 connector Back panel connectors 12 V processor core voltage connector 2 x 2 pin Rear chassis fan header 3 pin Processor socket Processor fan header 4 pin Serial port header Main power connector 2 x 12 pin Diskette drive connector DIMM 0 Channel A and B sockets DIMM 1 Channel A and B sockets Battery Front chassis fan header 3 pin Chassis intrusion header BIOS configuration jumper block Alternate front panel power LED header Front panel header Serial ATA connectors Hi speed USB 2 0 headers Speaker N lt X lt C 4 na O voz 3z C A T O 7 m 0 O w gt IDE connector IEEE 1394a header 2 gt Related Links Go to the following links for more information about e Desktop Board DQ965GF http www intel com design motherbd http support intel com support motherboards desktop e Supported processors http support intel com support motherboards desktop e Audio software and utilities http www intel com design motherbd e LAN software and drivers http www intel com design motherbd 12 Desktop Board Features Processor A CAUTION Failure to use an appropriate power supply and or not connecting the 12 V 2 x 2 pin power connector to the desktop board may result in damage to the board or the syst
21. BIOS from a bootable CD ROM bootable USB flash drive or other bootable USB media The utility available on the Intel World Wide Web site provides a simple method for creating a bootable CD ROM that will automatically update your BIOS The Iflash BIOS update files can also be extracted locally to your hard drive and copied to a bootable USB flash drive or other bootable USB media The Iflash Memory update utility allows you to e Update the BIOS and Intel Management Engine in flash memory e Update the language section of the BIOS NOTE Review the instructions distributed with the update utility before attempting a BIOS update CAUTION Do not interrupt the process or the system may not function properly 1 Uncompress the BIOS update file and copy the BIO file IFLASH EXE and ITK file optional to a bootable USB flash drive or other bootable USB media 2 Configure the BIOS or use the F10 option during POST to boot to the USB device 3 Manually run the IFLASH EXE file from the USB device and manually update the BIOS 63 Intel Desktop Board DO965GF Product Guide Recovering the BIOS 64 It is unlikely that anything will interrupt the BIOS update however if an interruption occurs the BIOS could be damaged Due to BIOS size and recovery requirements a CD R with the BIO file in the root directory will be required For more information about recovering the BIOS for desktop board DQ965GF go to http support intel com sup
22. BukopuctoByUTe 6arapei MpaBunbHoro Tuny iHaKWe CHYBATMME DA34K Bubyxy AKLJO MOXJIMBO BMKOPMCTAH 6arapel cr a yrunisyBarH Yrunizayia BHKODACTaHMX 6arapeli mae 6yru BUKOHaHa 3rigHO M CLEBMX HODM LO Dery IIOIOTb OXOPOHY ZJOBKITITS UPOZORN N V p pad v m ny baterie za nespr vn druh m ze doj t k v buchu Je li to mo n baterie by m ly b t recyklov ny Baterie je t eba zlikvidovat v souladu s m stn mi p edpisy o ivotnim prost ed ETTEVAATUST Kui patarei asendatakse uue ebasobivat t pi patareiga v ib tekkida plahvatusoht T hjad patareid tuleb v imaluse korral viia vastavasse kogumispunkti T hjade patareide raviskamisel tuleb j rgida kohalikke keskkonnakaitse alaseid reegleid FIGYELMEZTET S Ha az elemet nem a megfelel tipusura cser li felrobbanhat Az elemeket lehet s g szerint jra kell hasznos tani A haszn lt elemeket a helyi k rnyezetv delmi el ir soknak megfelel en kell kiselejtezni UZMAN BU Past v eksplozijas risks ja baterijas tiek nomain tas ar nepareiza veida baterij m Ja iesp jams baterijas vajadz tu nodot attiec gos pie em anas punktos Bateriju izme anai atkritumos j notiek saska ar viet jiem vides aizsardz bas noteikumiem D MESIO Naudojant netinkamo tipo baterijas renginys gali sprogti Kai tik imanoma baterijas reikia naudoti pakartotinai Panaudotas baterijas i mesti b tina pagal vietinius aplinkos apsaugos nuostatus ZN ATTENZ
23. Connection Front Panel No RXD 1g DTR 69 DSR 8g CTS No Connection Alternate Front Panel Power LED 0M19392 Item Description A HD Audio Link B IEEE 1394a C Front panel audio D Serial port E Alternate front panel power LED F Front panel G USB 2 0 Figure 22 Internal Headers 44 Installing and Replacing Desktop Board Components Installing a Front Panel Audio Solution for Intel High Definition Audio 8 NOTE Figure 22 C on page 44 shows the location of the yellow front panel audio header Table 4 shows the pin assignments for the front panel audio header Table 4 Front Panel Audio Header Signal Names for Intel High Definition Audio Pin Signal Name Pin Signal Name 1 PORT 1L 2 GND 3 PORT 1R 4 PRESENCE 5 PORT 2R 6 SENSE1_RETURN 7 SENSE_SEND 8 KEY no pin To install the cable that connects the front panel audio solution to the front panel audio header follow these steps 1 Observe the precautions in Before You Begin on page 27 2 Turn off all peripheral devices connected to the computer Turn off the computer and disconnect the AC power cord 3 Remove the cover 4 Install a correctly keyed and shielded front panel audio cable NOTE Some chassis still use a front panel audio solution based on the AC 97 audio specification Refer to Table 5 below to connect an AC 97 front panel solution to the front panel audio header on the board The front
24. Create Volume Exit the Option ROM user interface by pressing Esc or going to the EXIT option in the MAIN MENU Updating the BIOS Loading the Intel Matrix Storage Technology RAID Drivers and Software 1 Begin Windows Setup by booting from the Windows installation CD 2 At the beginning of Windows Setup press F6 to install a third party SCSI or RAID driver When prompted insert the diskette labeled Intel Matrix Storage Technology RAID Driver Note A USB floppy drive may be used if the board does not have a floppy drive connector Install the Intel ICH8R DO DH SATA RAID Controller Desktop ICH8R driver 3 Finish the Windows installation and install all necessary drivers 4 Install the Intel Matrix Storage Console software via the Intel Express Installer CD included with your desktop board or after downloading it from the Internet at http support intel com support motherboards desktop The Intel Matrix Storage Console software can be used to manage the RAID configuration Setting Up a RAID Ready System The Intel Matrix Storage Technology Console software offers the flexibility to upgrade from a single Serial ATA drive to RAID without reinstalling the operating system when a second SATA hard drive is added to the system Follow the steps described in the headings from this section Configuring the BIOS for Intel Matrix Storage Technology and Loading the Intel Matrix Storage Technology RAID Drivers and Software
25. DO965GF Product Guide Lead Free Desktop Board This desktop board is lead free although certain discrete components used on the board contain a small amount of lead which is necessary for component performance and or reliability This desktop board is referred to as Lead free second level interconnect The board substrate and the solder connections from the board to the components second level connections are all lead free Table 16 shows the various forms of the Lead Free 2 Level Interconnect mark as it appears on the board and 76 accompanying collateral Table 16 Lead Free Board Markings Description Mark Lead Free 2 Level Interconnect This symbol is used to identify electrical and electronic assemblies and components in which the lead Pb concentration level in the desktop board substrate and the solder connections from the board to the components second level interconnect is not greater than 0 196 by weight 1000 ppm 2 Level Interconnect 2nd lvl Intct 2LI Regulatory Compliance EMC Regulations Desktop Board DO965GF complies with the EMC regulations stated in Table 17 when correctly installed in a compatible host system Table 17 EMC Regulations Regulation FCC Class B ICES 003 Class B EN55022 1998 Class B EN55024 1998 AS NZS CISPR22 Class B CISPR 22 3 Edition Class B CISPR 24 1997 VCCI Class B Title Title 47 of the Code of Feder
26. Desktop Board DO965GF Product Guide Connecting Power Cables A CAUTION 50 Failure to use the appropriate power supply and or not connecting the 12 V 2 x 2 pin power connector to the desktop board may result in damage to the board or the system may not function properly The 2 x 12 pin main power connector on the desktop board is backwards compatible with ATX12V power supplies with 2 x 10 connectors Figure 25 shows the location of the desktop board power connectors 0M19394 Figure 25 Connecting Power Supply Cables 1 Observe the precautions in Before You Begin on page 27 Connect the main power supply cable to the 2 x 12 pin connector 3 Connect the 12 V processor core voltage power supply cable to the 2 x 2 pin connector n Installing and Replacing Desktop Board Components Other Connectors and Headers Figure 26 shows the location of the other connectors and headers on the desktop board E D OM19395 Item Description A PCI bus connector 2 B PCI bus connector 1 C PCI Express x1 connector D Diskette drive connector E Chassis intrusion header Figure 26 Location of Other Connectors and Headers 51 Intel Desktop Board DO965GF Product Guide Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before moving the jumper Moving the jumper with the power on may result in unreliable computer operation Figure 27 shows the location of
27. EC 60950 1 2001 First Information Technology Equipment Safety Part 1 General Edition Requirements International Place Battery Marking There is insufficient space on this desktop board to provide instructions for replacing and disposing of the Lithium ion coin cell battery For system safety certification the statement below or an equivalent statement is required to be permanently and legibly marked on the chassis near the battery A CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations Related Links For information about replacing the battery go to page 55 71 Intel Desktop Board DO965GF Product Guide European Union Declaration of Conformity Statement 72 We Intel Corporation declare under our sole responsibility that the product Intel Desktop Board DQ965GF is in conformity with all applicable essential requirements necessary for CE marking following the provisions of the European Council Directive 89 336 EEC EMC Directive and Council Directive 73 23 EEC Safety Low Voltage Directive The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions L This product follows the provisions of the European Directives 89 336 EEC and 73 23 EEC Cestina Tento vyrobek odpovid poza
28. I Express graphics card support via a PCI Express x16 connector 6 channel 5 1 onboard subsystem featuring Intel High Definition Audio interface SigmaTel STAC9227 audio codec HD Audio Link header One PCI Express x1 connector One PCI Express x16 connector Two PCI connectors Up to 10 USB 2 0 ports Six ports routed to the back panel Four ports routed to two USB headers Six Serial ATA SATA channels 3 0 Gb s via the ICH8 one device per channel Up to two IEEE 1394a ports One port routed to the back panel One port routed to a IEEE 1394a header One IDE interface with ATA 66 100 support two devices One diskette drive interface One VGA port One parallel port One serial port header PS 2 keyboard and mouse ports continued Intel Desktop Board DO965GF Product Guide Table 1 Feature Summary continued LAN Support e Gigabit 10 100 1000 Mb s LAN subsystem using the Intel 82566DM Gigabit Network Connection e Intel Active Management Technology Intel AMT with System Defense Feature BIOS e Intel Platform Innovation Framework for extensible firmware interface e 16 Mbit symmetrical flash memory Support for SMBIOS e Intel Rapid BIOS Boot e Intel Express BIOS Update Power e Support for Advanced Configuration and Power Interface ACPI Management e Suspend to RAM STR e Wake on USB PCI Express PS 2 LAN and front panel Hardware e Intel Quiet System Technolog
29. IS DOCUMENT EXCEPT AS PROVIDED IN INTEL S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT Intel products are not intended for use in medical life saving or life sustaining applications Intel may make changes to specifications and product descriptions at any time without notice Desktop Board DQ965GF may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are available on request Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order Copies of documents which have an ordering number and are referenced in this document or other Intel literature may be obtained from Intel Corporation by going to the World Wide Web site at http www intel com or by calling 1 800 548 4725 Intel the Intel logo Pentium and Celeron are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries Other names and brands may be claimed as the property of others Copyright 2006 2007 Intel Corporation All rights reserved Preface Th
30. Intel Desktop Board DQ965GF Product Guide Order Number D42087 003 Revision History Revision Revision History Pate 001 First release of the Intel Desktop Board DQ965GF Product Guide June 2006 002 Second release of the Intel Desktop Board DQ965GF Product Guide August 2006 003 Added operating system support and updated Chapter 4 December 2006 If an FCC declaration of conformity marking is present on the board the following statement applies FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For questions related to the EMC performance of this product contact Intel Corporation 5200 N E Elam Young Parkway Hillsboro OR 97124 1 800 628 8686 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation
31. JONI A 58 Riskju ta splu joni jekk il batterija tinbidel b tip ta batterija mhux korrett hatten g andhom ji u ri iklati fejn hu possibbli Ir rimi ta batteriji u ati g andu jsir skond ir regolamenti ambjentali lokali OSTRZE ENIE Ryzyko wybuchu w przypadku wymiany na baterie niew a ciwego typu W miar mo liwo ci baterie nale y podda recyklingowi Zu ytych baterii nale y pozbywa si zgodnie z lokalnie obowi zuj cymi przepisami w zakresie ochrony rodowiska Installing and Replacing Desktop Board Components To replace the battery follow these steps 1 2 a Observe the precautions in Before You Begin see page 27 Turn off all peripheral devices connected to the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter Remove the computer cover Locate the battery on the board see Figure 29 With a medium flat bladed screwdriver gently pry the battery free from its connector Note the orientation of the and on the battery Install the new battery in the connector orienting the and correctly Replace the computer cover OM19398 Figure 29 Removing the Battery 59 Intel Desktop Board DO965GF Product Guide 60 3 Updating the BIOS The BIOS Setup program can be used to view and change the BIOS settings for the computer You can access the BIOS Setup program by pressing the lt F2 gt key after the Pow
32. Overload Gaal Observe Safety and Regulatory Requirements GG Installing the IO Shield comica ANEREN ERR ea alaka Intel Desktop Board DO965GF Product Guide InstallingandRemovingtheDesktopBoard 30 Installing and Removing a Drocessor sense meses nemen 31 Installing a PrOCESSOM u yaa us ek sin a alar Baal sa galan olma a gege d 31 InstalliingtheProcessorFanHeatsSink 34 Connecting the Processor Fan Heat Sink Cable r 34 Removing the ee 35 InstallingandRemovingMemory aa 35 Guidelines for Dual Channel Memory Configuration 35 TAO OFFO DIMM Hai SE AE Ii INI RI e ER IR NNI enez an ine a 36 Three DIMMS epe eir ERR gk aral ka ug idam 37 Installing DIMMS occhi ne epi Ra ux Bak pr sara Bakaya hakuya wa BOX pal irene Es 37 Removing DIMMS anma ima e T pr ER PPP RR NER REMERPR ERAKSIR REX RP ARE PIRRRA EDT qo aaa eli 39 Installing and Removing a PCI Express X16 Card 40 InstallingaPCIExpressx16Card enne 40 Removing the PCI Express x16 Card eee ee eee eee eens eee eee ne eens eae ee ea eees 41 Connecting the IDE Cable akm maa mam EEN 42 Connecting the Serial ATA SATA Cable Gaal 43 ConnectingtolntemalHeaders 11 44 Installing a Fron
33. a certain level the BIOS Setup program settings stored in CMOS RAM for example the date and time might not be accurate Replace the battery with an equivalent one Figure 29 on page 59 shows the location of the battery CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations PRECAUTION Risque d explosion si la pile usag e est remplac e par une pile de type incorrect Les piles usag es doivent tre recycl es dans la mesure du possible La mise au rebut des piles usag es doit respecter les r glementations locales en vigueur en mati re de protection de l environnement FORHOLDSREGEL Eksplosionsfare hvis batteriet erstattes med et batteri af en forkert type Batterier bor om muligt genbruges Bortskaffelse af brugte batterier bor foreg i overensstemmelse med g ldende milj lovgivning OBS Det kan oppst eksplosjonsfare hvis batteriet skiftes ut med feil type Brukte batterier b r kastes i henhold til gjeldende milj lovgivning VIKTIGT Risk f r explosion om batteriet ers tts med felaktig batterityp Batterier ska kasseras enligt de lokala milj v rdsbest mmelserna VARO R j hdysvaara jos pariston tyyppi on v r Paristot on kierr tett v jos se on mahdollista K ytetyt paristot on h vitett v paikallisten ymp rist m r ysten mukaisesti 55
34. about how to prevent damage to hardware or loss of data NOTE NOTE Notes call attention to important information Intel Desktop Board DO965GF Product Guide Terminology The table below gives descriptions of some common terms used in the product guide Term Description GB Gigabyte 1 073 741 824 bytes GHZ Gigahertz one billion hertz KB Kilobyte 1024 bytes MB Megabyte 1 048 576 bytes Mbit Megabit 1 048 576 bits MHz Megahertz one million hertz Box Contents e Intel Desktop Board DQ965GF I O shield One diskette drive cable e One ATA 66 100 cable e Two locking Serial ATA cables e Intel Express Installer Driver CD ROM e Intel Express Installer Software CD ROM e Intel Matrix Storage Technology RAID driver diskette e Quick Reference poster e Configuration and battery caution statement label Contents 1 Desktop Board Features Supported Operating Systems oo EERE aaa Desktop Board Components na PEOCESSO A e Yi R e e MAIN MeIMO uy cinc ea ei ken sa Ba waves tenets weve Basa ala kaale al a wapu ini wai n es Intel Q965 Express Chipset amlar aya dial Intel 0965 Graphics Gubesvstem cece ee EEE EEE EEE aS GMA 3000 Graphics Controller Gara Onboard Audio Subsystem na Input Output 1 0 Controller cx yal are beaten r ayi a eel RR E e q LAN SUBSYSTEM nennen h qua suas sea sea sea sua sua sea sua sua suas sse nnn LAN Subsystem Goftware cc EEE EERE EERE EEE EEE RJ 45 LAN Connector LEDS es
35. al Regulations Parts 2 and 15 Subpart B Radio Frequency Devices USA Interference Causing Equipment Standard Digital Apparatus Canada Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment European Union Information Technology Equipment Immunity Characteristics Limits and methods of measurement European Union Australian Communications Authority Standard for Electromagnetic Compatibility Australia and New Zealand Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment International Information Technology Equipment Immunity Characteristics Limits and Methods of Measurement International Voluntary Control for Interference by Information Technology Equipment Japan Japanese Kanji statement translation This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment VCCI Ifthis is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual CORES TEERALIEXIEISEURMEEEXAXUIBEEE VCCI OX 234 242722ABffB8iisinXIE Cd CORB RERMCIEATICE amp BHigjcUCU 5 CORBP IY APTFLEY 2 7 RER T BASH RMB SRO J ral s PRR AAS IE TEU RMU RUE U C EU 77 Intel Desktop Board DO965GF Product Guide Korean Class B statement transl
36. ale y w miar mo liwo ci utylizowa zgodnie z odpowiednimi przepisami ochrony rodowiska A PRECAUTIE Risc de explozie daca bateria este nlocuit cu un tip de baterie necorespunz tor Bateriile trebuie reciclate dac este posibil Depozitarea bateriilor uzate trebuie s respecte reglement rile locale privind protectia mediului A BHAMMAHME Mpu ucnonb30BaHuu 6arapen HeCOOTBOTCTBy OuJero Turia CYLUECTBYET PUCK ee B3pbIBa barapen JomKHbl ObITb YTUNU3UPOBAHBI MO BOSMOXHOCTH YTUNUZALUA 6aTapen AOJDKHa IIDOBOZHTCA MO MpaBusiaM COOTBETCTBYIOLUUM MeCTHbBIM TDEOOBAHHAM UPOZORNENIE Ak bat riu vymen te za nespr vny typ hroz nebezpe enstvo jej v buchu Bat rie by sa mali podla mo nosti v dy recyklova Likvid cia pou it ch bat ri sa mus vykon va v s lade s miestnymi predpismi na ochranu ivotn ho prostredia AN POZOR Zamenjava baterije z baterijo druga nega tipa lahko povzro i eksplozijo Ce je mogo e baterije reciklirajte Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi A g ANYLADU sejonisssuiaYufinamlltuuumunasAnissuan mnilulilg arial lada 017 EE EE EE EK E E EE EE OH 57 Intel Desktop Board DO965GF Product Guide AN AN gt P P gt P UYARI Yanl t rde pil tak ld nda patlama riski vard r Piller m mk n oldu unda geri d n t r lmelidir Kullan lm piller yerel evre yasalar na uygun olarak at lmal d r OCTOPOTA
37. ard the protective processor cover Always replace the processor cover if the processor is removed from the socket 9 0M19383 Figure 9 Remove the Processor from the Protective Processor Cover 32 Installing and Replacing Desktop Board Components 6 Hold the processor with your thumb and index fingers oriented as shown in Figure 10 Make sure fingers align to the socket cutouts Figure 10 A Align notches Figure 10 B with the socket Figure 10 C Lower the processor straight down without tilting or sliding the processor in the socket 0M19384 Figure 10 Install the Processor 7 Pressing down on the load plate Figure 11 A close and engage the socket lever Figure 11 B 0M19385 Figure 11 Close the Load Plate 33 Intel Desktop Board DO965GF Product Guide Installing the Processor Fan Heat Sink Desktop Board DO965GF has an integrated processor fan heat sink retention mechanism RM For instructions on how to attach the processor fan heat sink to the integrated processor fan heat sink RM refer to the boxed processor manual or the Intel World Wide Web site at Integration of the Boxed Intel Pentium 4 Processor in the 775 Land Package Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink cable to the 4 pin processor fan header see Figure 12 A fan with a 4 pin connector as shown in Figure 12 A is recommended however a fan with a 3 pin connector Figure 12 B can
38. ated in Channel A DIMM 0 in order for it to enable Intel Quiet System Technology and Intel Active Management Technology 13 Intel Desktop Board DO965GF Product Guide The desktop board supports the dual or single channel memory configurations defined below Four 240 pin Double Data Rate 2 DDR2 SDRAM Dual Inline Memory Module DIMM connectors with gold plated contacts Support for Unbuffered non registered single or double sided DIMMs Non ECC DDR2 memory DIMM Type and Timings listed below Type Timing DDR2 800 5 5 5 or 6 6 6 only DDR2 667 5 5 5 only DDR2 533 4 4 4 only Serial Presence Detect SPD memory only Memory configurations listed below e Up to 2 0 GB utilizing 256 Mb technology e Up to 4 0 GB utilizing 512 Mb or 1 Gb technology e Up to 8 0 GB utilizing 1 Gb technology NOTE uz NOTE 1 Gb memory technology is not supported on DDR2 800 DIMMs Intel recommends using memory from the tested memory lists available at http www cmtlabs com mbsearch asp http www intel com products motherboard index htm iid HMPAGE Header 2 Pro duct MB Related Links Go to the following links or pages for more information about 14 SDRAM specifications http www intel com technology memory Installing memory page 35 in Chapter 2 Desktop Board Features Intel 0965 Express Chipset The Intel 0965 Express Chipset consists of the following devices e Intel 0965 Express Chipset G
39. ation This is household eguipment that is certified to comply with EMC requirements You may use this equipment in residential environments and other non residential environments Ensure Electromagnetic Compatibility EMC Compliance Before computer integration make sure that the power supply and other modules or peripherals as applicable have passed Class B EMC testing and are marked accordingly Pay close attention to the following when reading the installation instructions for the host chassis power supply and other modules e Product certifications or lack of certifications e External I O cable shielding and filtering Mounting grounding and bonding requirements e Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals as applicable are not Class B EMC compliant before integration then EMC testing may be required on a representative sample of the newly completed computer 78 Regulatory Compliance Product Certifications Board Level Certification Markings Desktop Board DO965GF has the following product certification markings Table 18 Product Certification Markings Description Mark UL joint US Canada Recognized Component mark Includes adjacent UL file number for Intel desktop boards E210882 WA US FCC Declaration of Conformity logo mark for Class B equipment Includes Intel name and DO965GF model designation Trade Na
40. consists of the following e Intel 82566DM Gigabit Network Connection with support for Intel Active Management Technology with System Defense Feature Alert Standard Format ASF 2 0 Virtual LAN driver support for Intel Virtualization Technology Intel VT partitions e RJ 45 connector with status indicator LEDs LAN Subsystem Software For LAN software and drivers refer to the DQ965GF link on Intel s World Wide Web site at http support intel com support motherboards desktop RJ 45 LAN Connector LEDs Two LEDs are built into the RJ 45 LAN connector located on the back panel see Figure 2 These LEDs indicate the status of the LAN A B OM19402 Figure 2 LAN Connector LEDs Table 3 describes the LED states when the board is powered up and the LAN subsystem is operating Table 3 LAN Connector LED States LED LED Color LED of Indicates A Green LAN link is not established S LAN link is established Blinking LAN activity is occurring s 10 Mb s data rate Gren On 100 Mb s data rate 1000 Mb s data rate 17 Intel Desktop Board DO965GF Product Guide Intel Active Management Technology Intel AMT with System Defense Feature NOTE Intel Active Management Technology offers IT organizations tamper resistant and persistent management capabilities Specifically Intel AMT is a hardware based solution that uses out of band communication to manage access client systems i
41. davk m evropskych sm rnic 89 336 EEC a 73 23 EEC Dansk Dette produkt er i overensstemmelse med det europaeiske direktiv 89 336 EEC amp 73 23 EEC Dutch Dit product is in navolging van de bepalingen van Europees Directief 89 336 EEC amp 73 23 EEC Eesti Antud toode vastab Euroopa direktiivides 89 336 EEC ja 73 23 EEC kehtestatud n uetele Suomi Tama tuote noudattaa EU direktiivin 89 336 EEC 73 23 EEC m r yksi Francais Ce produit est conforme aux exigences de la Directive Europ enne 89 336 EEC amp 73 23 EEC Deutsch Dieses Produkt entspricht den Bestimmungen der Europ ischen Richtlinie 89 336 EEC amp 73 23 EEC EAAnvik To nap v npoi v akoAou8Bel Tic laT El Tov Euponaikov O ny wv 89 336 EOK kai 73 23 EOK Magyar Eterm k megfelel a 89 336 EEC s 73 23 EEC Eur pai Ir nyelv el r sainak Icelandic bessi vara stenst regluger Evr pska Efnahags Bandalagsins n mer 89 336 EEC amp 73 23 EEC Italiano Questo prodotto conforme alla Direttiva Europea 89 336 EEC amp 73 23 EEC Latvie u Sis produkts atbilst Eiropas Direktivu 89 336 EEC un 73 23 EEC noteikumiem Lietuviy Sis produktas atitinka Europos direktyvu 89 336 EEC ir 73 23 EEC nuostatas Malti Dan il prodott hu konformi mal provvedimenti tad Direttivi Ewropej 89 336 EEC u 73 23 EEC Regulatory Compliance Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 89 336 EEC amp 73 23 EEC Polski Niniejszy pro
42. dukt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 89 336 EWG i 73 23 EWG Portuguese Este produto cumpre com as normas da Diretiva Europ ia 89 336 EEC amp 73 23 EEC Espafiol Este producto cumple con las normas del Directivo Europeo 89 336 EEC amp 73 23 EEC Slovensky Tento produkt je v sulade s ustanoveniami eur pskych direkt v 89 336 EEC a 73 23 EEC Sloven ina Izdelek je skladen z dolo bami evropskih direktiv 89 336 EGS in 73 23 EGS Svenska Denna produkt har tillverkats i enlighet med EG direktiv 89 336 EEC amp 73 23 EEC T rk e Bu r n Avrupa Birli i nin 89 336 EEC ve 73 23 EEC y nergelerine uyar Product Ecology Statements The following information is provided to address worldwide product ecology concerns and regulations Recycling Considerations As part of its commitment to environmental responsibility Intel has implemented the Intel9 Product Recycling Program to allow retail consumers of Intel s branded products to return used products to select locations for proper recycling Please consult the http www intel com intel other ehs product ecology Recycling Program htm for the details of this program including the scope of covered products available locations shipping instructions terms and conditions etc mx TE HERE EZ KYA SUPRA SCT Intel Product Recycling Program UR A el DA feVESEPEAR AA IU d IAE HI P ioi 95 38 E Hs ET HAERERAA iB Z7 http www intel com intel
43. ean EMC directive and Low Voltage directive as applicable should be obtained Additionally other directives such as the Radio and Telecommunications Terminal Equipment R amp TTE directive may also apply depending on product features In the United States A certification mark by a Nationally Recognized Testing Laboratory NRTL such as UL CSA or ETL signifies compliance with safety requirements Wiring and cables must also be UL listed or recognized and suitable for the intended use The FCC Class B logo for home or office use signifies compliance with electromagnetic interference EMI requirements In Canada A nationally recognized certification mark such as CSA or cUL signifies compliance with safety requirements The Industry Canada statement at the front of this product guide demonstrates compliance with Canadian EMC regulations
44. em may not function properly Desktop Board DQ965GF supports an Intel processor in the LGA775 package Processors are not included with the desktop board and must be purchased separately The processor connects to the desktop board through the LGA775 socket The supported processors list for Desktop Board DQ965GF is located on the web at http support intel com support motherboards deskto Related Links Go to the following links or pages for more information about e Instructions on installing or upgrading the processor page 31 in Chapter 2 Main Memory A CAUTION When connected to AC power the memory slots on the board will be powered and in use A red LED located near the memory slots will be lit if the memory slots are powered Installing or removing memory from the board while the memory slots are powered may result in damage to both memory and boara Before installing or removing memory disconnect the system from AC power and wait for the LED to go off before proceeding NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board should be populated with DIMMs that support the Serial Presence Detect SPD data structure If your memory modules do not support SPD you will see a notification to this effect on the screen at power up The BIOS will attempt to configure the memory controller for normal operation NOTE The Intel Management Engine in the chipset requires memory to be popul
45. emoves all non standby voltages When resuming from an AC power failure the computer returns to the power state it was in before power was interrupted either on or off The computer s response can be set by using the Last Power State feature in the BIOS Setup program s Boot menu The desktop board has two power connectors See Figure 25 on page 50 for the location of the power connectors Fan Headers The function operation of the fans is as follows 22 The fans are on when the computer is in the ACPI SO state The fans are off when the computer is in the ACPI S3 S4 or S5 state Each fan header is wired to a tachometer input of the hardware monitoring and control device All fan headers support closed loop fan control that can adjust the fan speed or switch the fan on or off as needed All fan headers have a 12 V dc connection The desktop board has a 4 pin processor fan header and two 3 pin chassis fan headers Desktop Board Features LAN Wake Capabilities AN CAUTION For LAN wake capabilities the 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply LAN wakeup capabilities enable remote wake up of the computer through a network The LAN subsystem monitors network traffic and upon detecting a Magic Packet frame it asserts a wake up signal that powers up the computer Wake
46. er On Self Test POST memory test begins and before the operating system boot begins This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility and how to recover the BIOS if an update fails Updating the BIOS with the Intel Express BIOS Update Utility With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows environment The BIOS file is included in an automated update utility that combines the functionality of the Intel Flash Memory Update Utility and the ease of use of Windows based installation wizards To update the BIOS with the Intel Express BIOS Update utility 1 Go to the Intel World Wide Web site http support intel com support motherboards desktop 2 Navigate to the DQ965GF page click view Latest BIOS updates and select the Express BIOS Update utility file 3 Download the file to your hard drive You can also save this file to a removable USB device This is useful if you are updating the BIOS for multiple identical systems 4 Close all other applications This step is required Your system will be rebooted at the last Express BIOS Update window 5 Double click the executable file from the location on your hard drive where it was saved This runs the update program 6 Follow the instructions provided in the dialog boxes to complete the BIOS update 61 Intel Desktop Board DO965GF Produc
47. et s prin A e EEN E AER EEN AN Intel Active Management Technology Intel AMT with System Defense Feature c0ococcoccocconconconnannnnnan nan nan narran narrar naar nar nnrnananans Hi Speed USB 2 0 SUPPO EE Enhanced IDE Interface coccccccocconconcnncnnnnn narran EE aaa Serial ATA iii a oa Exparidabllity ii a A A BOS iD e ak e e e Serial ATA and IDE Auto Configuration eee teeta eee ee mene PCI and PCI Express Auto Configuration rr Security PASSWOFS 0000 Trusted Platform Module CTDMI aaa aaa Hardware Management Features HardwareMonitoringandfanSpeedControl Chassis Intrusion Detection na Power Management FegtUres gege keen sa vana ar Sen Yalama malda ma yla laa E ER ERES Die jm Es Power Connectors u ety eeepc vp ERE EMI IR ll le Sline FEM QR VEDI FRE A e asa LAN Wake CapabilitieS GG aaa Instantly Available PC Technology On boardPowerindicatorLEDS G Gana Wake from USB asmak u uu u eege Lee de ka waskanda a a Ae OCA ka im q was da Wake from PS 2 Kevboard Mouse aaa PME Signal Wake upSupport amp ea aaa WAKE Signal Wake upSupport na DEE vans EET PLCS EE Re l TIME Clocks e E e e 2 Installing and Replacing Desktop Board Components Before YOU BE BEE Installation Precautions samara asena mam mee ke v Bram awpa aaa Gi olduki Prevent Power Supply
48. from LAN is disabled by default in the BIOS for power saving Wake from S5 must be enabled in the BIOS in order for Intel AMT Out of Band management to function Instantly Available PC Technology A CAUTIONS For Instantly Available PC technology the 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply and or effect ACPI S3 sleep state functionality Power supplies used with this desktop board must be able to provide enough standby current to support the standard Instantly Available ACPI S3 sleep state configuration If the standby current necessary to support multiple wake events from the PCI and or USB buses exceeds power supply capacity the desktop board may lose register settings stored in memory Instantly Available PC technology enables the board to enter the ACPI S3 Suspend to RAM sleep state While in the S3 sleep state the computer will appear to be off If the computer has a dual colored power LED on the front panel the sleep state is indicated by the LED turning amber When signaled by a wake up device or event the computer quickly returns to its last known awake state The desktop board supports the PCI Bus Power Management Interface Specification Add in cards that support this specification can participate in power management and can be used to wake the computer On board Power I
49. gle connector blue to the Intel desktop board Figure 20 A e Attach the cable end with the two closely spaced connectors gray and black to the drives Figure 20 B 0M19390 Figure 20 Connecting the IDE Cable Installing and Replacing Desktop Board Components Connecting the Serial ATA SATA Cable The SATA cable supports the Serial ATA protocol and connects a single drive to the desktop board For correct cable function 1 Observe the precaution in Before You Begin on page 27 2 Attach the locking cable end to the connector on the board Figure 21 A 3 Attach the cable end without the lock to the drive Figure 21 B OM19391 Figure 21 Connecting the Serial ATA Cable 43 Intel Desktop Board DO965GF Product Guide Connecting to Internal Headers Before connecting cables to the internal headers observe the precautions in Before You Begin on page 27 Figure 22 shows the location of the internal headers A HD Audio Link Ground 3 3V 1 5V Galo No STBY Connection Key no pin oim e 12V 1019 sp Ground Sense Send 7 Key no pin 33V CORE 88 7 B soo 1 TPA1 Port2L Sense Ret Key no pin Port1L 1 2 Ground No N Connection 12V Port1R 13 14 Presencett TPA2 Port2R 5 6 Sensel Ret Ground R6 5 Y SYNC aav sv PA dim LE J ES IS Vo Ground B2 M 1 8 BCLK A AN USB 1 USB 2 Power 5 V Power 5 V D D Ground Ground No Key no pin
50. he Maintenance menu Use the arrow keys to select Clear Passwords Press Enter and Setup displays a pop up screen requesting that you confirm clearing the password Select Yes and press Enter Setup displays the maintenance menu again Press F10 to save the current values and exit Setup Turn off the computer Disconnect the computer s power cord from the AC power source Remove the computer cover 12 To restore normal operation place the jumper on pins 1 2 as shown below 3 1 B Replace the cover plug in the computer and turn on the computer 53 Intel Desktop Board DO965GF Product Guide Back Panel Connectors NOTE The line out connector located on the back panel is designed to power either headphones or amplified speakers only Poor audio quality may occur if passive non amplified speakers are connected to this output Figure 28 shows the back panel connectors Wee OM19401 Figure 28 Back Panel Connectors 54 Installing and Replacing Desktop Board Components Replacing the Battery A A A A A coin cell battery CR2032 powers the real time clock and CMOS memory When the computer is not plugged into a wall socket the battery has an estimated life of three years When the computer is plugged in the standby current from the power supply extends the life of the battery The clock is accurate to 13 minutes year at 25 C with 3 3 VSB applied When the voltage drops below
51. is Product Guide gives information about board layout component installation BIOS update and regulatory requirements for Intel Desktop Board DQ965GF Intended Audience The Product Guide is intended for technically qualified personnel It is not intended for general audiences Use Only for Intended Applications All Intel desktop boards are evaluated as Information Technology Equipment I T E for use in personal computers PC for installation in homes offices schools computer rooms and similar locations The suitability of this product for other PC or embedded non PC applications or other environments such as medical industrial alarm systems test equipment etc may not be supported without further evaluation by Intel Document Organization The chapters in this Product Guide are arranged as follows 1 Desktop Board Features a summary of product features 2 Installing and Replacing Desktop Board Components instructions on how to install the desktop board and other hardware components 3 Updating the BIOS instructions on how to update the BIOS Configuring for RAID Intel Matrix Storage Technology information about configuring your system for RAID A Error Messages and Indicators information about BIOS error messages and beep codes B Regulatory Compliance safety and EMC regulations and product certifications Conventions The following conventions are used in this manual AN CAUTION Cautions warn the user
52. ith these instructions or the instructions for associated modules contact the supplier s technical support to find out how you can ensure that your computer meets safety and regulatory requirements Related Links 28 For information about regulatory compliance go to Appendix B on page 71 Installing and Replacing Desktop Board Components Installing the I O Shield The desktop board comes with an I O shield When installed in the chassis the shield blocks radio frequency transmissions protects internal components from dust and foreign objects and promotes correct airflow within the chassis Install the I O shield before installing the desktop board in the chassis Place the shield inside the chassis as shown in Figure 4 Press the shield into place so that it fits tightly and securely If the shield doesn t fit obtain a properly sized shield from the chassis supplier OM19400 Figure 4 Installing the I O Shield 29 Intel Desktop Board DO965GF Product Guide Installingand Removing the Desktop Board A CAUTION 30 Only qualified technical personnel should do this procedure Disconnect the computer from its power source before performing the procedures described here Failure to disconnect the power before you open the computer can result in personal injury or equipment damage Refer to your chassis manual for instructions on installing and removing the desktop board Figure 5 shows the location of the mounting scre
53. ithout the need to remove the BIOS configuration jumper It requires a blank CD R a read writeable CD drive and software capable of uncompressing and writing the ISO image file to CD The CD image uses ISOLINUX bootloader and automatically launches a script to upgrade the BIOS via the Iflash utility CAUTION Do not interrupt the process or the system may not function properly Follow these instructions to upgrade the BIOS using the ISO Image BIOS file 1 Download the ISO Image BIOS file 2 Using software capable of uncompressing and writing an ISO image file to CD burn the data to a blank CD NOTE AN Updating the BIOS NOTE Copying the ISO Image BIOS file to CD will not work The completed CD should contain multiple files and a directory 3 Insert the CD that was created in the CD ROM drive of the computer to be upgraded and boot the system 4 When the Press ENTER to continue booting from CD ROM prompt appears press the Enter key The system will boot from the hard drive if no key is pressed within 15 seconds 5 Atthe Welcome to the Intel Desktop Board BIOS Upgrade CD ROM page press any key to confirm the BIOS upgrade operation 6 Wait for the BIOS upgrade process to complete CAUTION DO NOT POWER DOWN YOUR COMPUTER before the update is complete The update may take up to 5 minutes Updating the BIOS with Iflash NOTE e With the Iflash Memory update utility you can update the system
54. me Model Number FG CE mark Declaring compliance to European Union EU EMC directive 89 336 EEC and Low Voltage directive 73 23 EEC CE Australian Communications Authority ACA C tick mark Includes adjacent Intel supplier code number N 232 Japan VCCI Voluntary Control Council for Interference mark B S Korea MIC Ministry of Information and Communication mark Includes adjacent MIC certification number CPU DQ965GF For information about MIC certification go to http support intel com support motherboards desktop c2 Taiwan BSMI Bureau of Standards Metrology and Inspections mark Includes adjacent Intel company number D33025 S Printed wiring board manufacturer s recognition mark Consists of a unique UL recognized manufacturer s logo along with a flammability rating solder side V 0 79 Intel Desktop Board DO965GF Product Guide Chassis and Component Certifications 80 Ensure that the chassis and certain components such as the power supply peripheral drives wiring and cables are components certified for the country or market where used Agency certification marks on the product are proof of certification Typical product certifications include In Europe The CE marking signifies compliance with all applicable European requirements If the chassis and other components are not properly CE marked a supplier s Declaration of Conformity statement to the Europ
55. mes Pin Signal Name Pin Signal Name 1 DCD 2 RXD 3 TXD 4 DTR 5 Ground 6 DSR 7 RTS 8 CTS 9 RI 10 No connection 47 Intel Desktop Board DO965GF Product Guide Connecting to the HD Audio Link Header See Figure 22 A for the location of the HD Audio Link header Table 9 shows the pin assignments for the header Table 11 HD Audio Link Header Signal Names Pin Signal Name 1 BLCK 3 RST 5 SYNC 7 SDO 9 SDI 11 No connection 13 No connection 15 No connection Pin Signal Name 2 Ground 3 3V 1 5V I O 6 Ground 8 3 3V CORE 10 12V 12 Key no pin 14 3 3V 1 5V STBY 16 Ground Connecting to the Flexible Audio System After installing the SigmaTel audio driver the multi channel audio feature can be enabled Figure 23 shows the back panel audio connectors The default connector assignments are shown in the table The connectors are retaskable using the audio 48 driver interface OM19406 Item Description A Line in retasking jack B Line out retasking jack C Mic in retasking jack Figure 23 Back Panel Audio Connectors Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Cables Connecting Chassis Fan Cables Connect the chassis fan cables to the two chassis fan headers on the desktop board Figure 24 shows the location of the chassis fan headers 0M19393 Figure 24 Location of Chassis Fan Headers 49 Intel
56. n addition to offering encrypted and persistent asset management and remote diagnostics and or recovery capabilities for networked platforms With Intel AMT IT organizations can easily get accurate platform information and can perform remote updating diagnostics debugging and repair of a system regardless of the state of the operating system and the power state of the system NOTE Intel AMT enabled enterprise management software is required to take advantage of Intel AMT platform management capabilities The key features of Intel AMT include e Secure Out of Band OOB system management that allows remote management of PCs regardless of system power or operating system state Remote troubleshooting and recovery that can significantly reduce desk side visits and potentially increasing efficiency of IT technical staff Proactive alerting that decreases downtime and minimizes time to repair e Third party non volatile storage that prevents users from removing critical inventory remote control or virus protection agents e Remote hardware and software asset tracking that eliminates time consuming manual inventory tracking which also reduces asset accounting costs System Defense Feature an Intel AMT feature for stopping the propagation of worms and viruses through the use of programmable packet filters in the integrated LAN controller The packet filters inspect all incoming and all outgoing packets and determine whether to bl
57. ndicator LEDs A CAUTION If the AC power has been switched off and the 5 V standby power indicator is still lit disconnect the power cord before installing or removing any devices connected to the board Failure to do so could damage the board and any attached devices 23 Intel Desktop Board DO965GF Product Guide A CAUTION When connected to AC power the memory slots on the board will be powered and in use A red LED Figure 3 B located near the memory slots will be lit if the memory slots are powered Installing or removing memory from the board while the memory slots are powered may result in damage to both memory and board Before installing or removing memory disconnect the system from AC power and wait for the LED to go off before proceeding The desktop board has two on board power indicators a 5 V standby power indicator green LED and a memory power indicator red LED shown in Figure 3 The 5 V standby power indicator Figure 3 A is lit when there is standby power still present on the board even when the computer appears to be off The memory power indicator Figure 3 B is lit when there is power to the memory slots LL Dann rss seis salata OM19399 Figure 3 Location of the On board Power Indicators Related Links 24 For more information on standby current reguirements for the desktop board refer to the Technical Product Specification by going to the following link finding the product
58. ock or pass the packets as configured There is no indication to the host that a packet has been blocked or accepted Related Links 18 Go to the following link for information about Intel Active Management Technology http www intel com technology manage iamt index htm Desktop Board Features Hi Speed USB 2 0 Support NOTE NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements even if no device or a low speed USB device is attached to the cable Use a shielded cable that meets the requirements for a full speed USB device The desktop board supports up to 10 USB 2 0 ports via ICH8 six ports routed to the back panel and four ports routed to two internal USB 2 0 headers USB 2 0 ports are backward compatible with USB 1 1 devices USB 1 1 devices will function normally at USB 1 1 speeds USB 2 0 support requires both an operating system and drivers that fully support USB 2 0 transfer rates Disabling Hi Speed USB in the BIOS reverts all USB 2 0 ports to USB 1 1 operation This may be required to accommodate operating systems that do not support USB 2 0 Enhanced IDE Interface The desktop board s IDE interface handles the exchange of information between the processor and peripheral devices such as hard disk drives and CD ROM drives The interface supports e Up to two IDE devices such as hard drives e ATAPI style devices such as CD ROM drives e Older PIO M
59. ode devices e Ultra DMA 33 and ATA 66 100 protocols Serial ATA The desktop board supports six Serial ATA channels 3 0 Gb s via ICH8 connecting one device per channel e Support for Native Command Queuing NCQ e Support for hot plug e RAID 0 1 5 and 10 Expandability For system expansion the desktop board provides the following e One PCI Express x16 connector e One PCI Express x1 connector e Two PCI bus connectors 19 Intel Desktop Board DO965GF Product Guide BIOS The BIOS provides the Power On Self Test POST the BIOS Setup program the PCI PCI Express and IDE auto configuration utilities and the video BIOS The BIOS is stored in a Serial Peripheral Interface SPI Flash device The BIOS can be updated by following the instructions on page 61 in Chapter 3 Serial ATA and IDE Auto Configuration If you install a Serial ATA or IDE device such as a hard drive in your computer the auto configuration utility in the BIOS automatically detects and configures the device for your computer You do not need to run the BIOS Setup program after installing a Serial ATA or IDE device You can override the auto configuration options by specifying manual configuration in the BIOS Setup program PCI and PCI Express Auto Configuration If you install a PCI PCI Express add in card in your computer the PCI PCI Express auto configuration utility in the BIOS automatically detects and configures the resources IRQs DMA channels
60. oftware by providing a protected space for key operations and other security critical tasks Using both hardware and software the TPM protects encryption and signature keys at their most vulnerable stages operations when the keys are being used unencrypted in plain text form The TPM is specifically designed to shield unencrypted keys and platform authentication information from software based attacks Related Links Go to the following links for information about Trusted Platform Technology http www intel com design motherbd http support intel com support motherboards desktop Hardware Management Features The hardware management features of Desktop Board DQ965GF enable the board to be compatible with the Wired for Management WfM specification The board has several hardware management features including the following e Fan speed monitoring and control e Thermal and voltage monitoring Chassis intrusion detection Hardware Monitoring and Fan Speed Control The features of the hardware monitoring and fan speed control include Monitoring of power supply voltages to detect levels above and below acceptable values e Intel Quiet System Technology delivering acoustically optimized thermal management 8 wore NOTE Memory must be installed in the Channel A DIMM 0 socket to enable Intel Quiet System Technology e Fan speed controllers and sensors integrated into the ICH8 e Thermal sensors in the processor GMCH
61. ont panel header Table 7 shows the pin assignments for the front panel header Table 7 Front Panel Header Pin Description In Out Pin Description In Out Hard Drive Activity LED Power LED 1 Hard disk LED pull up to Out 2 Front panel green LED Out 5 V 3 Hard disk active LED Out 4 Front panel yellow LED Out Reset Switch On Off Switch 5 Ground 6 Power switch In 7 Reset switch In 8 Ground Power Not Connected 9 Power Out 10 No pin l Installing and Replacing Desktop Board Components Connecting to the Alternate Front Panel Power LED Header Figure 22 E on page 44 shows the location of the alternate front panel power LED header Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header If your chassis has a three pin power LED cable connect it to this header Table 8 shows the pin assignments for the front panel header Table8 Alternate Front Panel Power LED Header 2 nop Connecting to the IEEE 1394a Header See Figure 22 B for the location of the blue IEEE 1394a header Table 9 shows the pin assignments for the header Table 9 IEEE 1394a Header Signal Names Signal Name i Signal Name Ground Ground Key no pin Ground Connecting to the Serial Port Header See Figure 22 D for the location of the serial port header Table 9 shows the pin assignments for the header Table 10 Serial Port Header Signal Na
62. or e Install and remove memory e Install and remove a PCI Express x16 card e Connect the IDE and Serial ATA cables e Connect to the internal headers e Connect the flexible audio system Connect the chassis fan and power cables e Set the BIOS configuration jumper e Clear passwords e Replace the battery Before You Begin A CAUTIONS The procedures in this chapter assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment Disconnect the computer from its power source and from any telecommunications links networks or modems before performing any of the procedures described in this chapter Failure to disconnect power telecommunications links networks or modems before you open the computer or perform any procedures can result in personal injury or equipment damage Some circuitry on the board can continue to operate even though the front panel power button is off Follow these guidelines before you begin e Always follow the steps in each procedure in the correct order e Set up a log to record information about your computer such as model serial numbers installed options and configuration information e Electrostatic discharge ESD can damage components Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad If
63. other ehs product ecology Recycling Program htm J RRC RUE ORK th Z Qa B ACH Get AAA 73 Intel Desktop Board DO965GF Product Guide Deutsch Als Teil von Intels Engagement f r den Umweltschutz hat das Unternehmen das Intel Produkt Recyclingprogramm implementiert das Einzelhandelskunden von Intel Markenprodukten erm glicht gebrauchte Produkte an ausgew hlte Standorte f r ordnungsgem Bes Recycling zur ckzugeben Details zu diesem Programm einschlieBlich der darin eingeschlossenen Produkte verf gbaren Standorte Versandanweisungen Bedingungen usw finden Sie auf der http www intel com intel other ehs product ecology Recycling Program htm Espafiol Como parte de su compromiso de responsabilidad medioambiental Intel ha implantado el programa de reciclaje de productos Intel que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado Consulte la http www intel com intel other ehs product ecology Recycling Program htm para ver los detalles del programa que incluye los productos que abarca los lugares disponibles instrucciones de env o t rminos y condiciones etc Francais Dans le cadre de son engagement pour la protection de l environnement Intel a mis en uvre le programme Intel Product Recycling Program Programme de recyclage des produits Intel
64. port motherboards deskto 4 Configuring for RAID Intel Matrix Storage Technology NOTE NOTE Intel Matrix Storage Technology requires a Microsoft Windows Vista Microsoft Windows XP or Microsoft Windows 2000 operating system and SATA hard drives Configuring the BIOS for Intel Matrix Storage Technology 1 Assemble your system and attach two or more SATA hard drives to the SATA connectors 2 Enter system BIOS Setup by pressing the F2 key after the Power On Self Test POST memory tests begin 3 Go to Advanced gt Drive Configuration gt Configure SATA as ensure that RAID is selected 4 Then save your settings by pressing lt F10 gt SATA Port Mapping Once RAID is enabled the SATA port mapping for this desktop board changes Figure 30 shows the original SATA port configuration for the board as indicated on the board silkscreen Figure 31 shows the SATA port configuration after RAID is enabled SATA 4 SATA 5 SATA 2 SATA 3 SATA 0 SATA 1 OM19897 Figure 30 Original SATA Port Mapping for Desktop Board DQ965GF 65 Intel Desktop Board DO965GF Product Guide SATA 2 SATA 3 SATA 4 SATA 5 SATA 0 SATA 1 OM19898 Figure 31 SATA Port Mapping for Desktop Board DQ965GF After RAID is Enabled AN CAUTION Exercise caution when replacing a failed drive within a RAID storage array Do not replace the failed drive based on the original SATA port mapping use the new mapping shown in Figure 31 66
65. pour permettre aux consommateurs de produits Intel de recycler les produits us s en les retournant des adresses sp cifi es Visitez la page Web http www intel com intel other ehs product ecology Recycling Program htm pour en savoir plus sur ce programme savoir les produits concern s les adresses disponibles les instructions d exp dition les conditions g n rales etc SES AITITE RARE BO REELT Uu ATEM UTIL J gt FR iE TRXEO ESI AGR EU CURES UU VETES AY FIR EU A Y FOIFLER ig t Uc WRB mn IKK ARANA nmn 070172 LOR MARIS http www intel com in tel other ehs product ecology Recycling Program htm X88 SCC SU 74 Regulatory Compliance Malay Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna pengguna runcit produk jenama Intel memulangkan produk terguna ke lokasi lokasi terpilih untuk dikitarkan semula dengan betul Sila rujuk http www intel com intel other ehs product ecology Recycling Program htm untuk mendapatkan butir butir program ini termasuklah skop produk yang dirangkumi lokasi lokasi tersedia arahan penghantaran terma amp syarat dsb Portuguese Como parte deste compromisso com o respeito ao ambiente a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados onde esses produtos s o
66. raphics and Memory Controller Hub GMCH with Direct Media Interface DMI interconnect e Intel 82801HO I O Controller Hub ICH8DO with DMI interconnect Related Link Go to the following link for more information about the Intel Q965 Express Chipset http developer intel com design nav pcserver htm Intel Q965 Graphics Subsystem The Intel Q965 Express Chipset contains two separate mutually exclusive graphics options Either the integrated GMA 3000 graphics controller is used or a PCI Express x16 add in card can be used When a PCI Express x16 add in card is installed the GMA 3000 graphics controller is disabled GMA 3000 Graphics Controller The GMA 3000 graphics controller features the following 667 MHZ core frequency e Enhanced 3D graphics e Supports flat panel displays up to 2048 x 1536 at 75 Hz refresh rate in dual channel mode or digital CRT HDTV up to 1920 x 1080 at 85 Hz refresh rate e Advanced Digital Display 2 card or Media Expansion Card ADD2 MEC support e Dynamic Video Memory Technology support NOTE NOTE A minimum of 512 MB of system memory is required in order for the Intel GMA 3000 integrated graphics controller to operate properly 15 Intel Desktop Board DO965GF Product Guide Onboard Audio Subsystem Desktop Board DO965GF has a flexible 6 channel 5 1 onboard audio subsystem that includes a SigmaTel STAC9227 audio codec and an HD Audio Link header The audio subsystem features Intel
67. ssseeeme mensem 47 11 HD Audio Link Header Signal Names eect eee eee eens eens teense ene ea ene ened 48 12 Jumper SettingsfortheBIOSSetupProgramModes 52 13 BEG BEE 69 14 BIOS Error Messages riri a sl akal a kl ma lm DIVI ap ald 69 15 Safety Regulations c o eec d dete e lala dekh ERE oyla eke pala eek 71 6 Eead Free Board Matkings eite tne tes inet panier EE 76 17 EMC Regulatiols i akmak teque teer la la Pr DC Ee Tp ND ede 77 18 Product Certification MarkingS mener 79 viii 1 Desktop Board Features This chapter briefly describes the main features of Intel Desktop Board DQ965GF Table 1 summarizes the major features of the desktop board Table 1 Feature Summary microATX 243 84 millimeters 9 60 inches x 243 84 millimeters 9 60 inches Support for an Intel processor in the LGA775 package For more information go to www intel com go findcpu Form Factor Processor Main Memory Chipset Graphics Audio Expansion Capabilities Peripheral Interfaces Four 240 pin DDR2 1 8 V SDRAM Dual Inline Memory Module DIMM Sockets 800 667 533 MHz single or dual channel DDR2 SDRAM interface Support for up to 8 GB of system memory Intel Q965 Express Chipset consisting of Intel Q965 Express Chipset Graphics and Memory Controller Hub GMCH Intel 82801HO I O Controller Hub ICH8DO Intel Q965 Express Chipset with Intel Graphics Media Accelerator 3000 PC
68. such a station is not available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis 27 Intel Desktop Board DO965GF Product Guide Installation Precautions When you install and test the Intel desktop board observe all warnings and cautions in the installation instructions To avoid injury be careful of Sharp pins on connectors Sharp pins on printed circuit assemblies e Rough edges and sharp corners on the chassis e Hot components such as processors voltage regulators and heat sinks e Damage to wires that could cause a short circuit Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel Prevent Power Supply Overload Do not overload the power supply output To avoid overloading the power supply make sure that the calculated total current loads of all the modules within the computer is less than the output current rating of each of the power supplies output circuits Observe Safety and Regulatory Requirements Read and adhere the instructions in this section and the instructions supplied with the chassis and associated modules If you do not follow these instructions and the instructions provided by the chassis and module suppliers you increase safety risk and the possibility of noncompliance with regional laws and regulations If the instructions for the chassis are inconsistent w
69. t Guide Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory Update Utility You can use the information in this section to update the BIOS using either the Iflash Memory Update Utility or the ISO Image BIOS update file Obtaining the BIOS Update File You can update to a new version of the BIOS by using the ISO Image BIOS update file recommended or Iflash BIOS update file The ISO Image BIOS update file is a standardized image of a bootable CD ROM that can be used to create a bootable CD that will update the BIOS The IFlash BIOS update file is a compressed file that contains the files you need to update the BIOS The IFlash BIOS update file contains e New BIOS file including the Intel Management Engine Firmware Image e Intel Integrator Toolkit Configuration File optional e Intel Flash Memory Update Utility You can obtain either of these files through your computer supplier or by navigating to the Desktop Board DQ965GF page on the Intel World Wide Web site at http support intel com support motherboards deskto Navigate to the DQ965GF page click view Latest BIOS updates and select the ISO Image BIOS Update or Iflash BIOS Update utility file Updating the BIOS with the ISO Image BIOS Update File 62 The ISO Image BIOS update allows for the update of an Intel Desktop Board BIOS to the latest production release regardless of the operating system installed on the computer s hard drive and w
70. t Panel Audio Solution for Intel High Definition Audio 45 ConnectingtotheUSB2 0Headers 46 ConnectingtotheFrontPanelHeader 46 Connecting to the Alternate Front Panel PowerLEDHeader 47 ConnectingtothelEEE1394aHeader 47 Connecting to the Serial PortHeader 47 Connecting to the HD Audio Link Header rr 48 ConnectingtotherFlexibleAudioSystem 48 Connecting Chassis Fan and Power Cables eene 49 Connecting Chassis Fan Cables eee a re RR ERREUR ERE ERR a RR EUER 49 Connecting Power Cables cisci nee irani en ED RE RELIER EYE E ERR pees ema lada 50 Other Connectors and Headets citet netus dai dented 51 Setting theBlIOSCorfigurationlumper 52 Clearing Passwords sika dei vira cas cen Eder eli ip ika EROR IEEE INERAT qua kaqqa E HR eliz 53 Back Panel Connectors uen aes err anin bana T NEEN 54 Updating the BIOS Updating the BIOS with the Intel Express BIOS UpdateUtility 61 Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory Update Ulf 62 ObtainingtheBIOS U pdaterile 62 Updating the BIOS with the ISO Image BIOS Update File
71. the desktop board s BIOS configuration jumper block OM19396 Figure 27 Location of the BIOS Configuration Jumper Block The three pin BIOS jumper block enables all board configurations to be done in the BIOS Setup program Table 12 shows the jumper settings for the BIOS Setup program modes Table 12 Jumper Settings for the BIOS Setup Program Modes Jumper Setting Description 3 1 Normal default 1 2 The BIOS uses the current configuration and passwords for booting 3 1 Configure 2 3 After the Power On Self Test POST runs the A BIOS displays the Maintenance Menu Use this menu to clear passwords 3 1 Recovery None The BIOS recovers data in the event of a failed BRA BIOS update 52 Installing and Replacing Desktop Board Components Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode 1 2 10 11 13 Observe the precautions in Before You Begin on page 27 Turn off all peripheral devices connected to the computer Turn off the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter Remove the computer cover Find the configuration jumper block see Figure 27 Place the jumper on pins 2 3 as shown below 3 1 o og Replace the cover plug in the computer turn on the computer and allow it to boot The computer starts the Setup program Setup displays t
72. u have the correct DIMM place it on the illustration of the DDR2 DIMM in Figure 16 All the notches should match with the DDR2 DIMM DDR2 Figure 16 Use DDR2 DIMMs 37 Intel Desktop Board DO965GF Product Guide NOTE Memory must be installed in the Channel A DIMM 0 socket to enable Intel Quiet System Technology and Intel Active Management Technology 38 To install a DIMM follow these steps 1 2 Observe the precautions in Before You Begin on page 27 Turn off all peripheral devices connected to the computer Turn off the computer and disconnect the AC power cord Remove the computer s cover and locate the DIMM sockets see Figure 17 0M19387 Figure 17 Installing a DIMM Make sure the clips at either end of the DIMM socket s are pushed outward to the open position Holding the DIMM by the edges remove it from its anti static package Position the DIMM above the socket Align the small notch at the bottom edge of the DIMM with the keys in the socket see inset in Figure 17 Insert the bottom edge of the DIMM into the socket When the DIMM is inserted push down on the top edge of the DIMM until the retaining clips snap into place Make sure the clips are firmly in place Replace the computer s cover and reconnect the AC power cord Installing and Replacing Desktop Board Components Removing DIMMs To remove a DIMM follow these steps MAIS SS Observe the precautions in Before You Begin on
73. w holes for Desktop Board DQ965GF OM19379 Figure 5 Desktop Board DO965GF Mounting Screw Hole Locations Installing and Replacing Desktop Board Components Installingand Removing a Processor Instructions on how to install the processor on the desktop board are given below Installing a Processor A CAUTION Before installing or removing the processor make sure the AC power has been removed by unplugging the power cord from the computer the standby power LED should not be lit see Figure 3 on page 24 Failure to do so could damage the processor and the board To install a processor follow these instructions 1 Observe the precautions in Before You Begin on page 27 2 Open the socket lever by pushing the lever down and away from the socket Figure 6 A and B 0M19380 Figure 6 Lift Socket Lever 3 Lift the load plate Figure 7 A Do not touch the socket contacts Figure 7 B 0M19381 Figure 7 Lift the Load Plate 31 Intel Desktop Board DO965GF Product Guide 4 Remove the plastic protective socket cover from the load plate see Figure 8 Do not discard the protective socket cover Always replace the socket cover if the processor is removed from the socket 0M19382 Figure 8 Remove the Protective Socket Cover 5 Remove the processor from the protective processor cover Hold the processor only at the edges being careful not to touch the bottom of the processor see Figure 9 Do not disc
74. y Intel QST fan speed control Management e Three fan headers e Three fan sensing inputs used to monitor fan activity e Remote diode temperature sensing e Voltage sensing to detect out of range values Related Links For more information about Desktop Board DQ965GF including the Technical Product Specification TPS BIOS updates and device drivers go to http support intel com support motherboards deskto Supported Operating Systems 10 The desktop board supports the following operating systems Microsoft Windows Vista Ultimate e Microsoft Windows Vista Enterprise e Microsoft Windows Vista Business Microsoft Windows Vista Home Premium e Microsoft Windows Vista Home Basic Microsoft Windows Vista Ultimate 64 bit edition e Microsoft Windows Vista Enterprise 64 bit edition Microsoft Windows Vista Business 64 bit edition Microsoft Windows Vista Home Premium 64 bit edition Microsoft Windows Vista Home Basic 64 bit edition Microsoft Windows XP Media Center Edition 2005 Microsoft Windows XP Professional Microsoft Windows XP Professional x64 Edition Microsoft Windows XP Home Edition e Microsoft Windows 2000 Desktop Board Features Desktop Board Components Figure 1 shows the approximate location of the major components on Desktop Board DQ965GF Wi OM19401 Figure 1 Desktop Board DQ965GF Components 11 Intel Desktop Board DO965GF Product Guide Table 2 Desktop Board DO

Download Pdf Manuals

Related Search

Related Contents

第14期定時株主総会招集ご通知    

Copyright © All rights reserved. Failed to retrieve file