Home

M5A78L-M LE/USB3

1. H g DIMM B1 Channel Sockets Channel A DIMM A1 lt a Channel B DIMM B1 ASUS M5A78L M LE USB3 E M MAIN L j v mm on om M5A78L M LE USB3 240 pin DDR3 DIMM sockets 1 4 2 Memory configurations You may install 1GB 2GB 4GB and 8GB unbuffered non ECC DDR3 DIMMs into the DIMM sockets WS You may install varying memory sizes in Channel A and Channel B The system maps the total size of the lower sized channel for the dual channel configuration Any excess memory from the higher sized channel is then mapped for single channel operation Always install DIMMs with the same CAS latency For optimal compatibility we recommend that you install memory modules of the same version or date code D C from the same vendor Check with the retailer to get the correct memory modules Due to the memory address limitation on 32 bit Windows OS when you install 4GB or more memory on the motherboard the actual usable memory for the OS can be about 3GB or less For effective use of memory we recommend that you do any of the following Use a maximum of 3GB system memory if you are using a 32 bit Windows OS Install a 64 bit Windows OS if you want to install 4GB or more on the motherboard For more details refer to the Microsoft support site at http support microsoft com kb 929605 en us This motherboard does not support DIMMs made up of 512Mb 6
2. 2 4 6 8 10 12 2 4 6 8 10 1296 2 4 3 Chipset NorthBridge Configuration DRAM Controller Configuration Bank Interleaving Auto Allows you to enable the bank memory interleaving Configuration options Disabled Auto Node Interleaving Disabled Allows you to enable the node memory interleaving Configuration options Disabled Auto Channel Interleaving Auto Allows you to enable the channel memory interleaving Configuration options Disabled Auto Memory Hole Remapping Enabled Allows you to enable or disable memory remapping around memory hole Configuration options Disabled Enabled DCT Unganged Mode Always Allows you to select unganged DRAM mode 64 bit width Configuration options Always Auto Power Down Enable Disabled Allows you to enable or disable DDR power down mode Configuration options Disabled Enabled ECC Configuration ECC Mode Disabled Enables or disables the DRAM ECC that allows the hardware to report and correct memory errors automatically Configuration options Disabled Basic Good Super Max User DRAM ECC Enable Enabled This item appears only when you set ECC Mode to User and allows hardware to report and correct memory errors automatically maintaining system integrity Internal Graphics Primary Video Controller GFX0 GPP IGFX PCI Selects the primary display adapter Configuration options
3. Submenu items Navigation keys 2 2 2 Menu bar The menu bar on top of the screen has the following main items Main For changing the basic system configuration Advanced For changing the advanced system settings Power For changing the advanced power management APM configuration Boot For changing the system boot configuration Tools For configuring options for special functions Exit For selecting the exit options and loading default settings To select an item on the menu bar press the right or left arrow key on the keyboard until the desired item is highlighted 2 2 3 Navigation keys At the bottom right corner of a menu screen are the navigation keys for that particular menu Use the navigation keys to select items in the menu and change the settings Z Some of the navigation keys differ from one screen to another ASUS M5A78L M LE USB3 2 5 2 2 4 Menu items The highlighted item on the menu bar displays the specific items for that menu For example selecting Main shows the Main menu items The other items Advanced Power Boot Tools and Exit on the menu bar have their respective menu items 2 2 5 Submenu items A solid triangle before each item on a menu screen means that the item has a submenu To display the submenu select the item and press lt Enter gt 2 2 6 Configuration fields These fields show the values for the menu items If an item is user configurable you can change the value of the field opposite
4. Auto 1T 2T Memory Voltage Auto Sets the memory voltage Configuration options Auto 1 350V 1 500V 1 650V 1 800V PCI PCle CLK Status Enabled Enables or disables clock for PCI PCle slot Configuration options Disabled Enabled ASUS M5A78L M LE USB3 2 11 2 12 2 4 2 CPU Configuration The items in this menu show the CPU related information that the BIOS automatically detects GART Error Reporting Disabled This option should remain disabled for the normal operation The driver developer may enable it for testing purpose Configuration options Disabled Enabled Microcode Updation Enabled Enables or disables Microcode Updation Configuration options Disabled Enabled Secure Virtual Machine Mode Disabled Enables or disables Secure Virtual Machine Mode SVM Configuration options Disabled Enabled Cool n Quiet Enabled Enables or disables the AMD Cool n Quiet technology Configuration options Enabled Disabled C1E Support Disabled Enables or disables the CPU Enhanced Halt C1E function a CPU power saving function in system halt state When this item is enabled the CPU core frequency and voltage will be reduced during the system halt state to decrease power consumption Configuration options Disabled Enabled Advanced Clock Calibration Disabled Adjusts the processor s overclocking capability When this item is set to Auto the BIOS automatically
5. GFXO GPP IGFX PCI GPP GFXO IGFX PCI PCI GFX0O GPP IGFX IGFX GFX0 GPP PCl GFXO primary video controller on a PCle x16 slot GPP primary video controller on a PCle x1 slot m IGFX onboard display output port PCI primary video controller on a PCI slot ASUS M5A78L M LE USB3 2 13 UMA Frame Buffer Size Auto Selects the UMA frame buffer size Configuration options Auto 32MB 64MB 128MB 256MB 512MB Z e The 512MB option only appears when you install 1GB system memory or more The 1GB option only appears when you install 2GB system memory or more Surround View Auto Disables or enables the Surround View function Configuration options Auto Disabled Enabled Z This item becomes user configurable when you install an ATI graphics card into the PCle x16 slot Frame Buffer Location Above 4G Configuration options Below 4G Above 4G 2 4 4 Onboard Devices Configuration Serial Port1 Address 3F8 IRQ4 Allows you to select the Serial Port1 base address Configuration options Disabled 3F8 IRQ4 2F8 IRQ3 SE8 IRQ4 2E8 IRQ3 HDAudio Controller Enabled Enables or disables the high definition audio controller Configuration options Disabled Enabled Front Panel Select HD Audio This item appears only when you set the previous item to Enabled Configuration options AC97 HD Audio OnBoard LAN Controller Enabled Configuration options Disabled Enabled OnBoard
6. cause you physical injury and damage to motherboard components 1 2 1 Placement direction When installing the motherboard place it into the chassis in the correct orientation The edge with external ports goes to the rear part of the chassis as indicated in the image 1 2 2 Screw holes Place six screws into the holes indicated by circles to secure the motherboard to the chassis N Do not overtighten the screws Doing so can damage the motherboard Place this side towards the rear of the chassis Chapter 1 Product introduction 1 2 3 Motherboard layout 1 2 3 4 1 19 8cm 7 8in Ho ULI AMD 760G 64bit 240 pin module A 5 9 o E E a ka A a st e SOCKET AM3 USB3 E12 gt PI i 1042A DDR3 DIMM_A1 DDR3 DIMM_B1 LAN_USB12 CHALTAN EATXPWR AUDIO v m Nm E EH Li 2 8111GR PCIEX16 ITITITTI M5A78L M LE USB3 Super VO BATTERY AMD SB710 Isi Se c pane EERE 887 VD2 USB78 USB56 SATA3G_1 SATA3G_2 SATA3G_3 SATA3G_4 aarp DEL Tee AREA EE 10 9 8 7 ASUS M5A78L M LE USB3 24 4cm 9 6in 1 2 4 Layout contents Connectors Headers Slots LED ATX power connectors 24 pin EATXPWR 4 pin ATX12V CPU and chassis fan connectors 4 pin CPU_FAN and 3 pin CHA_FAN AMD AM3 socket DDR3 DIMM slots Speaker connector 4 pin SPEAKER System panel connector 10 1 pin F PANEL SATA 3 0 Gb s connectors 7 pin SATA3G 1 4 US
7. Configuration options Disabled Enabled PF Set this item to Enabled to use the ASUS MyLogo2 feature ASUS M5A78L M LE USB3 2 19 AddOn ROM Display Mode Force BIOS Sets the display mode for option ROM Configuration options Force BIOS Keep Current Bootup Num Lock On Selects the power on state for the NumLock Configuration options Off On Wait for F1 If Error Enabled When this item is set to Enabled the system waits for the F1 key to be pressed when error occurs Configuration options Disabled Enabled 2 6 3 Security The Security menu items allow you to change the system security settings Select an item then press lt Enter gt to display the configuration options Change Supervisor Password Select this item to set or change the supervisor password The Supervisor Password item on top of the screen shows the default Not Installed After you set a password this item shows Installed To set a Supervisor Password 1 Select the Change Supervisor Password item and press Enter 2 On the password box key in a password containing up to six letters or numbers or both then press lt Enter gt 3 Confirm the password when prompted The message Password Installed appears after you successfully set your password To change the supervisor password follow the same steps as in setting a supervisor password To clear the supervisor password select the Change Supervisor Password then pre
8. E 2 7 Contents 2 4 2 5 2 6 2 7 2 8 2 3 4 Ee le 2 8 2 3 5 System Information Se gek Ne Ek ee ee 2 8 Advanced Mentis 2 9 2 4 1 JumperFree Configuration AE 2 9 2 4 2 E Ree lee 2 12 2 4 3 MA N OE OE N 2 13 2 4 4 Onboard Devices Configuration 2 14 2 4 5 F i mc 2 15 2 4 6 USB CO GUA mt 2 15 Power TE 2 16 2 5 1 Suspend Mode Auto a a a 2 16 2 5 2 ACPI 2 0 Support Enabled 2 16 2 5 3 ACPI APIC Support TIEnabled iese ee Re Re Re 2 16 2544 APM CORIIGUESUOD siese eN Lu uuu ee ein GOD 2 16 2 5 5 HW Monitor Seite e EE 2 17 2 5 6 Anti Surge Support Enabled 2 18 BOOT MENU l EE EE EE EE 2 19 2 6 1 Boot Device Priority EE 2 19 2 6 2 Boot Settings Configuration ee ee RR Re ER RR Re 2 19 2 6 3 RS UII Me teeta AA A N EE a EE nection 2 20 TOOLS MENU uu N EE EE aa aa arii 2 22 2 7 1 E 2 22 2 7 2 Re 2 22 2 grill PEER N 2 23 Safety information Electrical safety To prevent electrical shock hazard disconnect the power cable from the electrical outlet before relocating the system When adding or removing devices to or from the system ensure that the power cables for the devices are unplugged before the signal cables are connected If possible disconnec
9. This 2 pin connector is for the HDD Activity LED Connect the HDD Activity LED cable to this connector The HD LED lights up or flashes when data is read from or written to the HDD ATX power button soft off button 2 pin PWR_BTN This 2 pin connector is for the system power button Reset button 2 pin RESET This 2 pin connector is for the chassis mounted reset button for system reboot without turning off the system power Chapter 1 Product introduction 6 Front panel audio connector 10 1 pin AAFP This connector is for a chassis mounted front panel audio I O module that supports either High Definition Audio or AC 97 audio standard Connect one end of the front panel audio VO module cable to this connector ao tr gt E E Lu Lu T o s Qn o O ke Z Z 2 z H O O UI UI Ooo O zo Wa lt Z Z Z LJ AAFP PIN 1 2 Aammoa NE cr o o H g Eres emque z EE fr IC See 9 N E OoOo O Zo e Canal lt ES u ASUS e l t 2 4 S HD audio compliant Legacy AC 97 ua pin definition compliant definition M5A78L M LE USB3 Front panel audio connector Z We recommend that you connect a high definition front panel audio module to this connector to avail of the motherboard high definition audio capability e Ifyou want to connect a high definition
10. 2 0 Support Enabled Allows you to enable or disable the Advanced Configuration and Power Interface ACPI 2 0 support Configuration options Disabled Enabled 2 5 3 ACPI APIC Support Enabled Allows you to enable or disable the Advanced Configuration and Power Interface ACPI support in the Advanced Programmable Interrupt Controller APIC When set to Enabled the ACPI APIC table pointer is included in the RSDT pointer list Configuration options Disabled Enabled 2 5 4 APM Configuration Restore on AC Power Loss Power Off When this item is set to Power Off the system goes into off state after an AC power loss When this item is set to Power On the system goes on after an AC power loss When this item set to Last State the system goes into either off or on state whatever the system state was before the AC power loss Configuration options Power Off Power On Last State Power on From S5 By PME Disabled Enables or disables PME wake from sleep states Configuration options Disabled Enabled Power on From 5 By Ring Disabled Enables or disables ring to generate a wake event Configuration options Disabled Enabled Chapter 2 BIOS information Power on By PS 2 Keyboard Disabled Enables or disables PS 2 Keyboard to generate a wake event Configuration options Disabled Space Bar Power Key Ctrl Esc Power on From S5 By RTC Alarm Disabled Enables or disables RTC to generate a wak
11. B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with manufacturer s instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help to assure compliance with FCC regulations Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment N The use of shielded cables for connection of the monitor to the graphics card is reduired ASUS M5A78L M LE USB3 A 1 A 2 IC Canadian Compliance Statement Complies with the Canadian ICES 003 Class B specifications This device complies with R
12. LAN Boot ROM Disabled This item appears only when you set the previous item to Enabled Configuration options Disabled Enabled USB 3 0 Controller Enabled Allows you to enable or disable the USB 3 0 controller Configuration options Disabled Enabled Chapter 2 BIOS information 2 4 5 PCIPnP The PCI PnP menu items allow you to change the advanced settings for PCI PnP devices The menu includes setting IRQ and DMA channel resources for either PCI PnP or legacy ISA devices and setting the memory size block for legacy ISA devices AN Take caution when changing the settings of the PCI PnP menu items Incorrect field values can cause the system to malfunction Plug and Play O S No When this item is set to No BIOS configures all the devices in the system When this item is set to Yes and if you install a Plug and Play operating system the operating system configures the Plug and Play devices not required for boot Configuration options No Yes 2 4 6 USB Configuration The items in this menu allows you to change the USB related features Select an item then press lt Enter gt to display the configuration options FF The Module Version and USB Devices Enabled items show the auto detected values If no USB device is detected the item shows None USB Functions Enabled Allows you to enable or disable the USB functions Configuration options Disabled Enabled Pa The following items appear only when you
13. front panel audio module to this connector set the Azalia Front Panel item in the BIOS to HD See section 2 4 4 Onboard Devices Configuration for details e The front panel audio VO module is purchased separately 7 USB 2 0 connectors 10 1 pin USB56 USB78 These connectors are for USB 2 0 ports Connect the USB module cable to any of these connectors then install the module to a slot opening at the back of the system chassis These USB connectors comply with USB 2 0 specification that supports up to 480Mbps connection speed V Never connect a 1394 cable to the USB connectors Doing so will damage the motherboard Z The USB 2 0 module is purchased separately ASUS M5A78L M LE USB3 1 19 1 8 Software support 1 8 1 Installing an operating system This motherboard supports 32 bit 64 bit Windows XP 32 bit 64 bit Windows 7 Operating Systems OS Always install the latest OS version and corresponding updates to maximize the features of your hardware LA e Motherboard settings and hardware options vary Refer to your OS documentation for detailed information e Ensure that you install Windows XP Service Pack 3 or later versions before installing the drivers for better compatibility and system stability 1 8 2 Support DVD information The Support DVD that comes with the motherboard package contains the dr
14. mouse combo port This port is for a PS 2 keyboard mouse 2 Video Graphics Adapter VGA port This 15 pin port is for a VGA monitor or other VGA compatible devices 3 LAN RJ 45 port This port allows Gigabit connection to a Local Area Network LAN through a network hub LAN port LED indications I ED Activity Link LED Speed LED OFF No link OFF 10Mbps connection ORANGE Linked ORANGE 100Mbps connection 1Gbps connection LAN port 4 Line In port light blue This port connects to the tape CD DVD player or other audio sources 5 Line Out port lime This port connects to a headphone or a speaker In the 2 1 4 1 5 1 and 7 1 channel configurations the function of this port becomes Front Speaker Out 6 Microphone port pink This port connects to a microphone Z Refer to the audio configuration table below for the function of the audio ports in 2 1 4 1 5 1 or 7 1 channel configuration ASUS M5A78L M LE USB3 1 13 Audio 2 1 4 1 5 1 or 7 1 channel configuration Headset 4 1 channel 5 1 channel 7 1 channel 2 1 channel Light Blue Rear Line In panel Front Speaker Out Pink Rear panel Micin Mic In Bass Center Bass Center Lime Front panel Side Speaker Out Lime Rear panel Line Out Front Speaker Out Front Speaker Out Ax To configure a 7 1 channel audio output Use a chassis with HD audio module in the front panel to support a 7 1 channel audio
15. multi sectors transfers When this item is set to Auto the data transfer from and to the device occurs multiple sectors at a time if the device supports multi sector transfer feature When this item is set to Disabled the data transfer from and to the device occurs one sector at a time Configuration options Disabled Auto ASUS M5A78L M LE USB3 2 7 2 8 PIO Mode Auto Selects the PIO mode Configuration options Auto 0 1 2 8 4 DMA Mode Auto Selects the DMA mode Configuration options Auto SMART Monitoring Auto Sets the Smart Monitoring Analysis and Reporting Technology Configuration options Auto Disabled Enabled 32Bit Data Transfer Enabled Enables or disables 32 bit data transfer Configuration options Disabled Enabled 2 3 4 SATA Configuration The SATA Configuration menu allows you to configure your storage devices Select an item then press lt Enter gt to display the submenu OnChip SATA Channel Enabled Enables or disables the onboard channel SATA port Configuration options Disabled Enabled Z The following item only appears when you set OnChip SATA Channel to Enabled SATA Porti Port4 IDE Allows you to set the SATA configuration IDE Set to IDE when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices RAID Set to RAID when you want to create a RAID configuration from the SATA hard disk drives AHCI Set to AHCI
16. package Installing ASUS Update To install ASUS Update 1 Place the support DVD in the optical drive The Specials menu appears 2 Click the Utilities tab then click Al Suite II 3 Follow the onscreen instructions to complete the installation Fi Quit all Windows applications before you update the BIOS using this utility Updating the BIOS To update the BIOS 1 From the Windows desktop click Start gt Programs gt ASUS gt Al Suite II gt Al Suite II X XX XX to launch the Al Suite II utility The Al Suite Il Quick Bar appears 2 Click Update button from the Quick Bar and then click ASUS Update from the popup menu The ASUS Update main screen appears From the list select either of the following methods ASUS M5A78L M LE USB3 2 1 Updating from the Internet a Select Update BIOS from the Internet then click Next b Selectthe ASUS FTP site nearest you to avoid network traffic then click Next C From the FTP site select the BIOS version that you wish to download then click Next LA The ASUS Update utility is capable of updating itself through the Internet Always update the utility to avail all its features Updating from a BIOS file a Select Update BIOS from file then click Next b Locate the BIOS file from the Open window then click Open 3 Follow the onscreen instructions to complete the updating process 2 1 2 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update
17. panel connector BIOS 16Mb Flash ROM AMI BIOS PnP DMI v2 0 WfM2 0 SM BIOS 2 5 ACPI v3 0a Support DVD Drivers ASUS PC Probe II ASUS Update Anti Virus software OEM version Form factor uATX form factor 9 6 in x 7 8 in 24 4 cm x 19 8 cm Fi Specifications are subject to change without notice viii Product introduction 1 1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings AN e Unplug the power cord from the wall socket before touching any component e Before handling components use a grounded wrist strap or touch a safely grounded object or a metal object such as the power supply case to avoid damaging them due to static electricity e Hold components by the edges to avoid touching the ICs on them e Whenever you uninstall any component place it on a grounded antistatic pad or in the bag that came with the component e Before you install or remove any component ensure that the ATX power supply is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals or components ASUS M5A78L M LE USB3 1 1 1 2 Motherboard overview Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits Ka Unplug the power cord before installing or removing the motherboard Failure to do so can
18. set USB Functions to Enabled USB 2 0 Controller Enabled Enables or disables USB 2 0 Controllers Configuration options Disabled Enabled Legacy USB Support Auto Allows you to enable or disable support for Legacy USB storage devices including USB flash drives and USB hard drives Setting to Auto allows the system to detect the presence of USB devices at startup If detected the USB controller legacy mode is enabled If no USB device is detected the legacy USB support is disabled Configuration options Disabled Enabled Auto ASUS M5A78L M LE USB3 2 15 2 16 2 5 Power menu The Power menu items allow you to change the settings for the Advanced Configuration and Power Interface ACPI and the Advanced Power Management APM Select an item then press lt Enter gt to display the configuration options M5A78L M LE USB3 BIOS Setup Version 0211 Main Advanced Boot Tools Exit Power Settings Select the ACPI state used for System Suspend ACPI 2 0 Support Enabled ACPI APIC Support Enabled k APM Configuration k HW Monitor Configuration Anti Surge Support Enabled Select Screen Select Item Change Option General Help Save and Exit Exit v02 61 C Copyright 1985 2015 American Megatrends Inc 2 5 1 Suspend Mode Auto Allows you to select the Advanced Configuration and Power Interface ACPI state to be used for system suspend Configuration options S1 POS Only S3 Only Auto 2 5 2 ACPI
19. the BIOS without using an OS based utility Before you start using this utility download the latest BIOS file from the ASUS website at Ge www asus com To update the BIOS using EZ Flash 2 1 Insert the USB flash disk that contains the latest BIOS file to the USB port then launch EZ Flash 2 in either of these two ways Press lt Alt gt lt F2 gt during POST e Enterthe BIOS setup program Go to the Tools menu to select EZ Flash 2 and press lt Enter gt to enable it Press lt Tab gt to switch between drives until the correct BIOS file is found 2 When the correct BIOS file is found EZ Flash 2 performs the BIOS update process and automatically reboots the system when done L 3 This function supports USB flash disks with FAT 32 16 format and single partition only e DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure 2 2 Chapter 2 BIOS information 2 1 3 ASUS CrashFree BIOS 3 ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process You can restore a corrupted BIOS file using the motherboard support DVD or a USB flash drive that contains the updated BIOS file aN Before using this utility rename the BIOS file in the USB flash drive into MA78LMU3 ROM e Download the latest BIOS file from the ASUS website at www asus com Recovering the BIOS To recover the BIOS 1 Tu
20. the item You cannot select an item that is not user configurable A configurable field is enclosed in brackets and is highlighted when selected To change the value of a field select it then press lt Enter gt to display a list of options Refer to 2 2 7 Pop up window D ATBL M LE USB3 BIOS Setup Version 0211 2 2 7 Pop up window Main Advanced Boot Tools Exit a fewer Settings EEN Select the ACPI state Select a menu item then press used for System ACPI 2 0 Support Enabled PEG lt Enter gt to display a pop up ACPI APIC support Enabled window with the configuration ra i options for that item Anti Surge Support Select Screen Select Item Change Field 2 2 8 Scroll bar and Batt A scroll bar appears on the right side a O conyrigne E of a menu screen when there are Pop up window items that do not fit on the screen Press the Up Down arrow keys or Page Up Page Down keys to display the other items on the screen Scroll bar 2 2 9 General help At the top right corner of the menu screen is a brief description of the selected item Chapter 2 BIOS information 2 3 Main menu When you enter the BIOS Setup program the Main menu screen appears giving you an overview of the basic system information Refer to section 2 2 1 BIOS menu screen for information on the menu screen items and how to navigate through them M5A78L M LE USB3 BIOS Setup Version 0211 Advanced Power Boot T
21. use 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot 5 Secure the card to the chassis with the screw you removed earlier 6 Replace the system cover 1 5 2 Configuring an expansion card After installing the expansion card configure it by adjusting the software settings 1 Turn on the system and change the necessary BIOS settings if any See Chapter 2 for information on BIOS setup 2 Assign an IRQ to the card 3 Install the software drivers for the expansion card k When using PCI cards on shared slots ensure that the drivers support Share IRQ or that the cards do not need IRQ assignments Otherwise conflicts will arise between the two PCI groups making the system unstable and the card inoperable Chapter 1 Product introduction 1 5 3 PCI slot The PCI slot supports cards such as a LAN card SCSI card USB card and other cards that comply with PCI specifications 1 5 4 PCI Express 2 0 x1 slot This motherboard supports PCI Express x1 network cards SCSI cards and other cards that comply with the PCI Express specifications 1 5 5 PCI Express x16 slot This motherboard supports PCI Express x16 network cards SCSI cards and other cards that comply with the PCI Express specifications IRQ assignments for this motherboard PCIEx16_1 shared PCIEx1_1 shared PCI1 slot Realtek LAN controller shared HD audio shared _ OnC
22. when you want the SATA hard disk drives to use the AHCI Advanced Host Controller Interface The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands 2 3 5 System Information This menu gives you an overview of the general system specifications The BIOS automatically detects the items in this menu BIOS Information Displays the auto detected BIOS information Processor Displays the auto detected CPU specification System Memory Displays the auto detected system memory Chapter 2 BIOS information 2 4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices N Take caution when changing the settings of the Advanced menu items Incorrect field values can cause the system to malfunction M5A78L M LE USB3 BIOS Setup Version 0211 Advanced Power Boot Tools Exit Advanced Settings Adjust System Frequency Voltage etc CPU Configuration Chipset Onboard Devices Configuration PCIPnP USB Configuration Select Screen Select Item Change Field Select Field General Help Save and Exit Exit v02 61 C Copyright 1985 2015 American Megatrends Inc 2 4 1 JumperFree Configuration The items and configuration options in this menu may vary depending on the AMD CPU Gem type CPU OverClocking Overclock Profile S
23. 3777 Fax 1 510 608 4555 Web site http www asus com us Technical Support Support fax 1 812 284 0883 Telephone 1 812 282 2787 Online support http www service asus com ASUS COMPUTER GmbH Germany and Austria Address Harkort Str 21 23 D 40880 Ratingen Germany Fax 49 2102 959911 Web site http www asus com de Online contact http eu rma asus com sales Technical Support Telephone 49 1805 010923 Support Fax 49 2102 9599 1 1 Online support http www asus com de support ASUS M5A78L M LE USB3 A 5 eunyeuBbls coz Bupmew 32 Buixiyje uibaq 0 189A SL0 r0 L 4 91eG uong1i1e 5 d ueus Aller owen O39 UONSOd LLEOSL 49A Bupeuw Auuuojuoo 93 Bueu 39 SASSA SHotH n3 S9 LL0ZD4 6002 29 ON 03 uonembay 8002 6421 ON 03 uolle n6 t 10Z 19 ON 03 uonembay 6002 842 ON O3 uonembay 9An981JIg d13 O23 S6L 600zL1 ELO ZY 9002 1 08609 N3 X LLOZ Z Y 2002 S9009 NA LLOZ 2LW 9002 1 068609 NA aanoedd GAT 03 S6 900eX 800c LLEC9 NA VLA d L62 20 NA 200 S8 0S NA VLA L L62 20 NA 0L0z 6 v29 Na O Z0 S00 40 9007 L L 8002 60 2002 90 4002 LA 92 ZOE NA 10 6002 l l LA 29 ZOE NA LA 92 ZOE NA 10 6002 L LA Z rhS ZOE NA LA 2 687 LOE NA 90 ZL02 Z LA 68 LOE N3 ZA LL 68 LOE NA 20 1102 Z GA 2 806 LOE NA V LA 668 LOE NA SO LLOZ LZ SA 1 806
24. 4 x Serial ATA 3Gb s connectors support RAID 0 1 10 and JBOD LAN Realtek 8111GR Gigabit LAN Controller s Realtek ALC887 8 channel High Definition Audio CODEC Dedicated audio PCB layers Separate layers for left and right channels to guard the quality of the sensitive audio signals Premium Japanese made audio capacitors Provide warm natural and immersive sound with exceptional clarity and fidelity Use the chassis with HD audio module in the front panel to support 8 channel audio output continued on the next page Vii M5A78L M LE USB3 specifications summary USB 8 USB 2 0 ports 4 at mid board 4 at back panel 2 USB 3 0 ports 2 at back panel ASUS Unique ASUS EPU Features EPU Core Unlocker ASUS Exclusive Features Anti Surge ASUS All Dk Hour Solid Capacitors RAM Overcurrent Protection ESD Guards Stainless Steel Back I O ASUS Quiet Thermal Solution ASUS Fan Xpert ASUS EZ DIY ASUS CrashFree BIOS 3 ASUS EZ Flash 2 ASUS MyLogo 2 Back panel UO ports 1 x PS 2 Keyboard Mouse combo port 1 x DVI port 1 x D Sub port 1 x LAN RJ 45 port 1 x COM port 3 x Audio jacks 2 x USB 3 0 ports 4 x USB 2 0 ports Internal I O connectors 2 x USB 2 0 connectors support additional 4 USB 2 0 ports 4 x SATA 3 0Gb s connectors 1 x CPU fan connector 1 x Chassis fan connector 1 x 24 pin EATX power connector 1 x 4 pin ATX 12V power connector 1 x Front panel audio connector 1 x Internal Speaker connector 1 x System
25. 4MB chips or less Chapter 1 Product introduction SPD which is the standard way of accessing information from a memory module Under the default state some memory modules for overclocking may operate at a lower frequency than the vendor marked value To operate at the vendor marked or at a higher frequency refer to section 2 4 Advanced menu for manual memory frequency adjustment Z e The default memory operation frequency is dependent on its Serial Presence Detect e For system stability use a more efficient memory cooling system to support a full memory load 2 DIMMs or overclocking condition e Visit the ASUS website at www asus com for the latest OVL 1 4 3 Installing a DIMM ASUS M5A78L M LE USB3 1 9 To remove a DIMM 1 5 Expansion slots In the future you may need to install expansion cards The following sub sections describe the slots and the expansion cards that they support Unplug the power cord before adding or removing expansion cards Failure to do so may cause you physical injury and damage motherboard components 1 5 1 Installing an expansion card To install an expansion card 1 Before installing the expansion card read the documentation that came with it and make the necessary hardware settings for the card 2 Remove the system unit cover if your motherboard is already installed in a chassis 3 Remove the bracket opposite the slot that you intend to use Keep the screw for later
26. B 2 0 connectors 10 1 pin USB56 USB78 Clear RTC RAM 2 pin CLRTC 10 Front panel audio connector 10 1 pin AAFP 1 2 3 4 5 6 7 8 9 1 3 Central Processing Unit CPU The motherboard comes with an AM3 socket designed for AMD FX Series Phenom II Athlon I SempronTM 100 Series Processors A The AM3 socket has a different pinout from the AM2 AM2 socket Ensure that you usd a CPU designed for the AM3 socket The CPU fits in only one correct orientation DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU Chapter 1 Product introduction CPU installation 1 3 1 1 5 ASUS M5A78L M LE USB3 1 3 2 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary Chapter 1 Product introduction To uninstall the CPU heatsink and fan assembly ASUS M5A78L M LE USB3 1 8 1 4 System memory 1 4 1 Overview This motherboard comes with two Double Data Rate 3 DDR3 Dual Inline Memory Modules DIMM sockets A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched differently to prevent installation on a DDR2 DIMM socket DDR3 modules are developed for better performance with less power consumption The figure illustrates the location of the DDR3 DIMM sockets
27. Hz x9 1800MHz x9 5 1900MHz x10 0 2000MHz x10 5 2100MHz x11 2200MHz CPU NB Frequency Auto Sets the CPU Northbridge frequency Configuration options Auto B40MHz 1050MHz 1260MHz 1470MHZ 1680MHz 1890MHz 2100MHz CPU Over Voltage Auto Sets the CPU over voltage The valid value ranges vary depending on your CPU model Use lt gt lt gt keys to adjust the ratio Configuration options Auto VDDNB Over Voltage Auto Sets the VDDNB over voltage The valid value ranges vary depending on your CPU model Use lt gt lt gt keys to adjust the ratio Configuration options Auto LoadLine Calibration Auto Sets the LoadLine Configuration options Auto 0 3 225 6 45096 9 675 12 90 87 075926 90 3 93 525926 96 75 100 aN If the system becomes unstable after changing the setting set it back to Auto for safe mode HT Link Speed Auto Sets the HyperTransport link speed Configuration options Auto 200MHz 400MHZz 600MHZz B00MHZ 1000MHz 1200MHz 1400MHz 1600MHz 1800MHz 2000MHz DRAM Timing Config Auto Configuration options Auto Manual Ff The following items only appear when you set DRAM Timing Config to Manual Memory Clock Speed 400MHz Selects the memory clock frequency programming method Configuration options 400MHz 533MHZ 667MHz 800MHz 2 10 Chapter 2 BIOS information DRAM Timing Configuration The confi
28. I RRO ae LO FAL VCCI B This is a Class B product based on the standard of the VCCI Council If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual KC Korea Warning Statement BF zl OS REST xA e aalt AVS AAAS Fe AAA ASte BE HASE go 2E daa AFR AE d i 4 333482 45142544 223 94992 209 AE Q 3 ae uch Appendices REACH Complying with the REACH Registration Evaluation Authorisation and Restriction of Chemicals regulatory framework we published the chemical substances in our products at ASUS REACH website at http csr asus com english REACH htm DO NOT throw the motherboard in municipal waste This product has been designed to enable proper reuse of parts and recycling This symbol of the crossed out wheeled bin indicates that the product electrical and electronic equipment should not be placed in sss municipal waste Check local regulations for disposal of electronic products DO NOT throw the mercury containing button cell battery in municipal waste This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste ASUS Recycling Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment We believe in providing solutions for you to be able to responsibly recycle our prod
29. LOE NA LA Z 68r LOE NA 0 002 2 0 6A LLS LOE N3 V LA F 68r LOE NA 80 0102 L E LA 2 Obb 00 NA V LA 68r LOE NA 80 0102 L 9 LA L 0r 00 NA 6 LA L 68 LOE NA 90 2102 SELA 82 00 NZ 60 2 1 02 LL Z002 LL S00Z S0 6002 90 2002 60 LLOZ i t P Z 60 0102 I S i is Z 9An99JIQ 3 LL98 03 9 666 L L LOZ L LW Z002 020SS NA 9002 2V 00c LV L00c LOSS NA 8002 00019 NA 6002 cV 900c 2 00019 NA O0LOc vc0SS NA LHOSOVTOLOSGEOSS N3 X A119941q DINS 03 801 700cX S A119 4Ip Buiwojo eui jo slu ui uinb i jerjuesse aui uj uuojuo5 8S01 31 W 18ZV SIN eureu I pOlN pueoquayjo eureu 19npoid snjejedde Buimollo ay aieloep ANVINHAD Anunog NJ NILYY 0880p EZ LZ H1S LHOMYVH AUD sse ppy HquiS H31ndWOO SNSY edoun3 u eanewuaseidei pezuouiny NVMIVL ZL I3dlV1 nOLI3d PH 3LETT OSI ON AP ss ippV ONI HALNANOO MPLSNSV daunjpoejynueyy THIETHJH 31 HATS HI poubisiapun au IM AYULOJUOD JO uone DI LCrOpL JASA S107 LZ Adv sed eungeusig JU9pis2Jg suv 9A91S WBN S UOSIod oArnejueso1dow uoreedo pomsapun osneo Aew yey ou r jiour S urpn our p Ar o5 1 souaTOpIoyuT Aue 3dooo 3snui IMAP STU T pue eouoJogrojur TUE sneo JOU ABUT IMAP siu T suontpuoo om SUTMOTTOF om o1 3oofqns
30. NGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Offer to Provide Source Code of Certain Software This product contains copyrighted software that is licensed under the General Public License GPL under the Lesser General Public License Version LGPL and or other Free Open Source Software Licenses Such software in this product is distributed without any warranty to the extent permitted by the applicable law Copies of these licenses are included in this product Where the applicable license entitles you to the source code of such software and or other additional data you may obtain it for a period of three years after our last shipment of the product either 1 for free by downloading it from http support asus com download or 2 for the cost of reproduction and shipment which is dependent on the preferred carrier and the location where you want to have it shipped to by sending a request to ASUSTeK Computer Inc Legal Compliance Dept 15 Li Te Rd Beitou Taipei 112 Taiwan In y
31. SS 210 of Industry Canada This Class B device meets all the requirements of the Canadian interference causing equipment regulations This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Cut appareil num rique de la Classe B est conforme la norme NMB 003 du Canada Cet appareil num rique de la Classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Cet appareil est conforme aux normes CNR exemptes de licence d Industrie Canada Le fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne doit pas provoquer d interf rences et 2 cet appareil doit accepter toute interf rence y compris celles susceptibles de provoquer un fonctionnement non souhaite de l appareil Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications This class B digital apparatus complies with Canadian ICES 003 VCCI Japan Compliance Statement VCCI Class B Statement CORB 7ARRRRARETT ORG BILLTUETA ODRED ZS le ris MERS Jk TREND EE ERETGIEELTTERPY ET HUB RE CPEs TIE L
32. U FAN PWM CPU FAN IN GND gt CPU FAN PWR O M5A78L M LE USB3 Fan connectors DO NOT forget to connect the fan cables to the fan connectors Insufficient air flow inside the system may damage the motherboard components These are not jumpers DO NOT place jumper caps on the fan connectors ASUS M5A78L M LE USB3 The CPU_FAN connector supports a CPU fan of maximum 2A 24W fan power e Only the 4 pin CPU fan support the ASUS Fan Xpert feature 2 ATX power connectors 24 pin EATXPWR 4 pin ATX12V These connectors are for an ATX power supply The plugs from the power supply are designed to fit these connectors in only one orientation Find the proper orientation and push down firmly until the connectors completely fit m N NM Ca ATX12V EATXPWR OO aa 3 Volts GND a 12 Volts 5 Volts 12 Volts 5 Volts 5V Standby 5 Volts Power OK 5 Volts GND GND Pe PINI 5 Volts GND zz GND GND oo 5 Volts PSON GND GND 3 Volts 12 Volts 3 Volts 3 Volts PIN 1 M5A78L M LE USB3 ATX power connectors NA We recommend that you use an ATX 12V Specification 2 0 compliant power supply unit PSU with a minimum of 300W power rating This PSU type has 24 pin and 4 pin power plugs If you intend to use a PSU with 20 pin and 4 pin power plugs ensure that the 20 pin power plug can provide at least 15 A on 12 V and that
33. adjusts this function When this item is set to All Cores the processor has the best overclocking performance When this item is set to Per Core the processor s overclocking capability is enhanced Configuration options Disabled Auto All Cores Per Core By Hotkey Z The following items appear only when you set Advanced Clock Calibration to Auto All Cores or Per Core Unleashing Mode Disabled Enable the Unleashing Mode to get full computing power of the processor However this might make your system unstable depending on your processor s overclocking capability Configuration options Enabled Disabled Active CPU Cores Auto Allows you to manually turn ON OFF a process core Configuration options Auto Manual 2nd 3rd 4th Core On These items appear only when you set Active CPU Cores to Manual Configuration options On Off Value All Cores 2 This item appears only when you set Advanced Clock Calibration to All Cores It allows you to set the overclocking percentage for all the processor cores as a whole Configuration options 0 2 4 6 8 10 1296 2 4 6 8 10 12 Chapter 2 BIOS information Value Core 0 Core 1 Core 2 Core 3 2 These items only appear when you set Advanced Clock Calibration to Per Core and allow you to set the overclocking percentage for each process core separately Configuration options 0
34. ar User Password Select this item to clear the user password Password Check Setup When set to Setup BIOS checks for user password when accessing the Setup utility When setto Always BIOS checks for user password both when accessing Setup and booting the system Configuration options Setup Always ASUS M5A78L M LE USB3 2 21 2 22 2 7 Tools menu The Tools menu items allow you to configure options for special functions Select an item then press lt Enter gt to display the sub menu M5A78L M LE USB3 BIOS Setup Version 0211 Tools Settings Press ENTER to run SS y a sajaswss the utility to select and update BIOS This utility supports k ASUS O C Profile 1 FAT 12 16 32 r w 2 NTFS read only 3 CD DISC read only ma Select Screen tl Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02 61 C Copyright 1985 2015 American Megatrends Inc 2 7 1 ASUS EZ Flash 2 Allows you to run ASUS EZ Flash 2 When you press lt Enter gt a confirmation message appears Use the left right arrow key to select between Yes or No then press lt Enter gt to confirm your choice See section 2 1 2 for details 2 7 2 ASUS O C Profile This item allows you to store or load multiple BIOS settings Add Your CMOS Profile Allows you to save the current BIOS file to the BIOS Flash In the Name sub item key in your profile name and press lt Enter gt and then choose a profile number
35. dam AS da mE a Bes alind o E10372 First Edition April 2015 Copyright 2015 ASUSTeK COMPUTER INC All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of ASUSTeK COMPUTER INC ASUS Product warranty or service will not be extended if 1 the product is repaired modified or altered unless such repair modification of alteration is authorized in writing by ASUS or 2 the serial number of the product is defaced or missing ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL ASUS ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFITS LOSS OF BUSINESS LOSS OF USE OR DATA INTERRUPTION OF BUSINESS AND THE LIKE EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY AND ARE SUBJECT TO CHA
36. e event Configuration options Disabled Enabled 2 5 5 HW Monitor Configuration CPU Temperature xxx C xxx F or Ignored MB Temperature xxx C xxx F or Ignored The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures Select Ignored if you do not wish to display the detected temperatures CPU Chassis Fan Speed N A xxxxRPM or Ignored The onboard hardware monitor automatically detects and displays the CPU Chassis fan speeds in rotations per minute RPM If the fan is not connected to the motherboard the field shows N A Select gnored if you do not want the detected speed to be displayed VCORE Voltage 3 3V Voltage 5V Voltage 12V Voltage xx xxxV or Ignored The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators CPU Q Fan Function Enabled Enables or disables the ASUS Q Fan feature that smartly adjusts the CPU fan speeds for more efficient system operation Configuration options Disabled Enabled Z The following items appear only when you set CPU Q Fan Function to Enabled CPU Fan Speed Low Limit 200 RPM Allows you to manually set a lower limit for the CPU fan speed If the CPU fan speed is below the specified limit the system sends out warning beeps Configuration options 600 RPM 500 RPM 400 RPM 300 RPM 200 RPM Ignored CPU Q Fan Mode Standard Allows you to set the appropria
37. elects the CPU overclocking options to achieve desired CPU internal frequency Configuration options Manual Auto Overclock Profile Test Mode Z The following item appears only when you set CPU Overclocking to Manual CPU HT Reference Clock MHz 200 Sets the CPU HT Reference Clock Configuration options Min 200 Max 550 fF The following item appears only when you set CPU Overclocking to Overclock Profile Overclock Options Auto Selects the overclocking profile Configuration options Auto Overclock 296 Overclock 5 Overclock 8 Overclock 10 GPU Overclocking Auto Configures the GPU overclocking Configuration options Auto Manual Ff The following item appears only when you set GPU Overclocking to Manual GPU Engine Clock 350 Sets the GPU Engine Clock Use lt gt lt gt keys to adjust the ratio or input a number between 200 and 350 ASUS M5A78L M LE USB3 2 9 PCIE Overclocking Auto Configures the PCIE overclocking Configuration options Auto Manual Z The following item only appears when you set PCIE Overclocking to Manual PCIE Clock 100 Sets the PCIE Clock Use lt gt lt gt keys to adjust the ratio or input a number between 100 and 150 CPU Ratio Auto Sets the CPU ratio Configuration options Auto x4 0 800MHz x4 5 900MHZ x5 0 1000MHZ x5 5 1100MHZ x6 0 1200MHZ x6 5 1300MHz x7 1400MHZ x7 5 1500MHz x8 0 1600MHZ x8 5 1700M
38. en Sie bitte der CE Konformit tserkl rung Italiano AsusTek Inc con la presente dichiara che questo dispositivo conforme ai requisiti essenziali e alle altre disposizioni pertinenti alle direttive CE Per maggiori informazioni fate riferimento alla dichiarazione di conformit CE Komnanusa ASUS 3aaBaser YTO 3T0 ycrpoltcTBO COOTBeTCTByeT OCHOBHBIM TpeGoBaHHsM H IDyTHM COOTBETCTByIOIIIHM YCJIOBHSM enporielickux mmpekruB IHogpo nyro undjopwaruro noxa rylicra cuorpure B tekgrapaliun COOTBETCTBHA BEarapckH C Hacrosmoro AsusTek Inc qeknapupa ue Topa ycTpolicTBO B CBOTBETCTBHE CC CbIIeCTBeHHTe H3HCKBAHUSI H ADYTHTE HIDUJIOKHMH HocTaHoBJIeHHs Ha MpekTuBuTe CE Bwxre CE nekrapanusra 3a CBBMECTHMOCT 3a TOBeye uH OpMarms Hrvatski AsusTek Inc ovim izjavljuje da je ovaj uredaj sukladan s bitnim zahtjevima i ostalim odgovaraju im odredbama CE direktiva Vi e pojedinosti potra ite u CE izjavi o sukladnosti e tina Spole nost AsusTek Inc t mto prohla uje e toto za zen spl uje z kladn po adavky a dal p slu n ustanoven sm rnic CE Dal podrobnosti viz Prohl en o shod CE Dansk AsusTek Inc Erkl rer hermed at denne enhed er i overensstemmelse med hovedkravene and andre relevante bestemmelser i CE direktiverne Du kan l se mere i CE overensstemmelseserkl ring Nederlands AsusTek Inc verklaart hierbij dat dit apparaat compatibel is met de essenti le vereisten en andere relevante bepal
39. gn means that you must press the enclosed key Example Enter means that you must press the Enter or Return key Key1 Key2 Key3 If you must press two or more keys simultaneously the key names are linked with a plus sign Package contents Check your motherboard package for the following items Motherboard ASUS M5A78L M LE USB3 motherboard Cables 2 x Serial ATA 3 0 Gb s cables Accessories 1 x I O Shield Application DVD Support DVD Documentation User Guide Fi If any of the above items is damaged or missing contact your retailer M5A78L M LE USB3 specifications summary AMD Socket AM3 for AMD FX Phenom II Athlon II Sempron 100 series processors AMD Cool n Quiet Technology Supports CPU up to 125W Refer to www asus com for the AMD CPU support list Chipset AMD 760G 780L SB710 Front side bus Up to 5 2GT s HyperTransport 3 0 interface Memory Dual channel memory architecture 2 x 240 pin DIMM slots support maximum 16GB unbuffered ECC and non ECC DDR3 1866 1600 1333 1066MHz memory modules A AMD FX Series CPU on this motherboard supports up to DDR3 1866MHz as its standard memory frequency Due to CPU specification AMD AM3 CPUs on this motherboard support up to DDR3 1833MHz Refer to www asus com for the latest Memory QVL Qualified Vendors List Expansion slots 1 x PCle 2 0 x16 slot 1 x PCle 2 0 x1 slot 1 x PCI slot Storage RAID
40. guration options for some of the following items vary depending on the DIMMs you install on the motherboard DRAM CAS Latency Auto Configuration options Auto 4 CLK 12 CLK DRAM RAS to CAS Delay Auto Configuration options Auto 5 CLK 12 CLK DRAM RAS PRE Time Auto Configuration options Auto 5 CLK 12 CLK DRAM RAS ACT Time Auto Configuration options Auto 15 CLK 80 CLK DRAM READ to PRE Time Auto Configuration options Auto 4 CLK 5 CLK 6 CLK 7 CLK DRAM Row Cycle Time Auto Configuration options Auto 12 CLK 42 CLK DRAM WRITE Recovery Time Auto Configuration options Auto 5 CLK 6 CLK 7 CLK 8 CLK 10 CLK 12 CLK DRAM RAS to RAS Delay Auto Configuration options Auto 4 CLK 5 CLK 6 CLK 7 CLK DRAM READ to WRITE Delay Auto Configuration options Auto 8 CLK 17 CLK DRAM WRITE to READ Delay DD Auto Configuration options Auto 2 CLK 10 CLK DRAM WRITE to READ Delay SD Auto Configuration options Auto 4 CLK 5 CLK 6 CLK 7 CLK DRAM WRITE to WRITE Timing Auto Configuration options Auto 2 CLK 10 CLK DRAM READ to READ Timing Auto Configuration options Auto 8 CLK 10 CLK DRAM REF Cycle Time Auto Configuration options Auto 90ns 110ns 160ns 300ns 350ns DRAM Refresh Rate Auto Configuration options Auto Every 7 8ms Every 3 9ms DRAM Command Rate Auto Configuration options
41. hip SATA OnChip OHCI 1 shared OnChip OHCI 2 shared ASM1042A shared ASUS M5A78L M LE USB3 1 6 Headers Clear RTC RAM 2 pin CLRTC This header allows you to clear the Real Time Clock RTC RAM in CMOS You can C lear the CMOS memory of date time and system setup parameters by erasing the CMOS RTC RAM data The onboard button cell battery powers the RAM data in CMOS which include system setup information such as system passwords 1a Tom O o H CLRTC C lt AE E ES zz 78L M LE USI EI To erase the RTC RAM 1 SH Sr I Turn OFF the computer and unplug the power cord Use a metal object such as a screwdriver to short the two pins Plug the power cord and turn ON the computer Hold down the lt Del gt key during the boot process and enter BIOS setup to re enter data e Ifthe steps above do not help remove the onboard battery and short the two pins again to clear the CMOS RTC RAM data After clearing the CMOS reinstall the battery e You do not need to clear the RTC when the system hangs due to overclocking For system failure due to overclocking use the CPU Parameter Recall C P R feature Shut down and reboot the system then the BIOS automatically resets parameter settings to default values Chapter 1 Product introduction 1 7 Connectors 1 7 1 Rear panel connectors 1 PS 2 keyboard
42. ingen van CE richtlijnen Raadpleeg de CE verklaring van conformiteit voor meer details Eesti K esolevaga kinnitab AsusTek Inc et see seade vastab CE direktiivide oluliste n uetele ja teistele asjakohastele s tetele Vt ksikasju CE vastavusdeklaratsioonist Suomi AsusTek Inc vakuuttaa t ten ett t m laite on CE direktiivien olennaisten vaatimusten ja muiden asiaan kuuluvien lis ysten mukainen Katso lis tietoja CE vaatimustenmukaisuusvakuutuksesta EAAnvueg Me to rrap y n AsusTek Inc AnAwvel ott OUTA n ouokev OULLOPQOWVETAL HE uc BEHENWOEIG ATIAITIOEIG KAL GAAEG OXETIK G lAT EEI Twv Odnyiwv tng EE To nepioo tepe errrou psgig AVATPEETE otnv Aron gt uuu ppuonc EE Magyar Az AsusTek Inc ezennel kijelenti hogy a k sz l k megfelel a CE ir nyelvek alapvet k vetelm nyeinek s ide vonatkoz egy b rendelkez seinek Tov bbi r szletek rt tekintse meg a CE megfelel s gi nyilatkozatot Latviski L dz ar o AsusTek Inc pazi o ka ier ce atbilst b tiskaj m pras b m un citiem saisto ajiem nosac jumiem kas nor d ti CE direkt v Lai uzzin tu vair k skatiet CE Atbilst bas deklar ciju Lietuvi iuo dokumentu bendrov AsusTek Inc parei kia kad is renginys atitinka pagrindinius CE direktyv reikalavimus ir kitas susijusias nuostatas Daugiau informacijos rasite CE atitikties deklaracijoje Norsk AsusTek Inc erkl rer herved at denne enheten er i samsvar med ho
43. ivers software applications and utilities that you can install to avail all motherboard features LA The contents of the Support DVD are subject to change at any time without notice Visit the ASUS website at www asus com for updates To run the Support DVD Place the Support DVD into the optical drive If Autorun is enabled in your computer the DVD automatically displays the Specials screen Click Drivers Utilities Make Disk Manual and Contact tabs to display their respective menus LA The following screen is for reference only Click an icon to display ASUS Insti Support DVD motherboard information Click an item to install Z If Autorun is NOT enabled on your computer browse the contents of the Support DVD to L locate the file ASSETUP EXE from the BIN folder Double click the ASSETUP EXE to run the DVD Chapter 1 Product introduction BIOS information 2 1 Managing and updating your BIOS L Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to restore the BIOS in the future Copy the original motherboard BIOS using the ASUS Update utility 2 1 1 ASUS Update utility The ASUS Update is a utility that allows you to manage save and update the motherboard BIOS in Windows environment e ASUS Update requires an Internet connection either through a network or an Internet Service Provider ISP eg e This utility is available in the support DVD that comes with the motherboard
44. ntains the following parts Chapter 1 Product introduction This chapter describes the features of the motherboard and the new technology it supports Chapter 2 BIOS information This chapter tells how to change system settings through the BIOS Setup menus Detailed descriptions of the BIOS parameters are also provided vi Where to find more information Refer to the following sources for additional information and for product and software updates 1 ASUS websites The ASUS website provides updated information on ASUS hardware and software products Refer to the ASUS contact information 2 Optional documentation Your product package may include optional documentation such as warranty flyers that may have been added by your dealer These documents are not part of the standard package Conventions used in this guide To ensure that you perform certain tasks properly take note of the following symbols used throughout this manual DANGER WARNING Information to prevent injury to yourself when trying to complete a task CAUTION Information to prevent damage to the components when trying to complete a task k N IMPORTANT Instructions that you MUST follow to complete a task Z NOTE Tips and additional information to help you complete a task Typography Bold text Indicates a menu or an item to select Italics Used to emphasize a word or a phrase Key Keys enclosed in the less than and greater than si
45. ntend to create a Serial ATA RAID set using these connectors set the type of the SATA connectors in the BIOS to RAID See section 2 3 4 SATA Configuration for details You must install Windows XP Service Pack 3 or later version before using Serial ATA hard disk drives The Serial ATA RAID feature is available only if you are using Windows XP SP3 or later version When using hot plug and NCQ set the type of the SATA connectors in the BIOS to AHCI See section 2 3 4 SATA Configuration for details 4 Speaker connector 4 pin SPEAKER This 4 pin connector is for the chassis mounted system warning speaker The speaker allows you to hear system beeps and warnings EI _ SPEAKER 5 O D QQ EE o O Oo M5A78L M LE USB3 Speaker Out connector ASUS M5A78L M LE USB3 1 17 5 System panel connector 10 1 pin F PANEL This connector supports several chassis mounted functions F PANEL PWR LED PWR_LED PWR GND HWRST PIN 1 NC Grou nd HDD_LED HDD_LED System power LED 2 pin PWR_LED This 2 pin connector is for the system power LED Connect the chassis power LED cable to this connector The system power LED lights up when you turn on the system power and blinks when the system is in sleep mode Hard disk drive activity LED 2 pin HDD LED
46. ools Exit Main Settings Use ENTER TAB 34 30 or SHIFT TAB to System Date Thu 08 14 2011 select a field SATA3G_1 Not Detected Use or to SATA3G 2 Not Detected configure system SATA3G 3 INot Detected Time SATA3G 4 INot Detected SATA Configuration System Information Select Screen Select Item Change Field Select Field General Help Save and Exit Exit v02 61 C Copyright 1985 2015 American Megatrends Inc 2 3 1 System Time xx xx xx Allows you to set the system time 2 3 2 System Date Day xx xx xxxx Allows you to set the system date 2 3 3 SATA3G_1 4 While entering Setup the BIOS automatically detects the presence of SATA devices There is a separate submenu for each SATA device Select a device item then press lt Enter gt to display the SATA device information The BIOS automatically detects the values opposite the dimmed items Device LBA Large Mode Block Multi Sector Transfer Mode PIO Mode DMA Mode SMART monitoring and 32Bit Data Transfer These values are not user configurable These items show Not Detected if no SATA device is installed in the system LBA Large Mode Auto Enables or disables the LBA mode Setting this item to Auto enables the LBA mode if the device supports this mode and if the device was not previously formatted with LBA mode disabled Configuration options Disabled Auto Block Multi Sector Transfer M Auto Enables or disables data
47. our request please provide the name model number and version as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary object code This offer is valid to anyone in receipt of this information ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address gpl asus com stating the product and describing the problem please DO NOT send large attachments such as source code archives etc to this email address Contents Safety In iorimali i sessie V About this OUIdE mt DE Ede ee V Package comens E vii M5A78L M LE USB3 specifications summary vii Chapter 1 Product introduction 1 1 Bei6re Vou proceed LL eende REK SE ei KNOW eN Ge we ae eek 1 1 12 Motherboard OV SI VIG WG ascii u uuu l l l l l l i l AR edge SEEK 1 2 13 Central Processing Unit CPU 1 4 1 3 1 CPU I o e Em 1 5 1 3 2 CPU heatsink and fan as
48. output 7 USB 2 0 ports 1 and 2 These two 4 pin Universal Serial Bus USB ports are for USB 2 0 1 1 devices 8 USB 3 0 ports 1 and 2 These two 9 pin Universal Serial Bus USB ports connect to USB 3 0 2 0 devices e Due to USB 3 0 controller limitations USB 3 0 devices can only be used under a Windows OS environment and after USB 3 0 driver installation e The plugged USB 3 0 device may run on xHCI or EHCI mode depending on the operating system s setting e USB 3 0 devices can only be used for data storage e We strongly recommend that you connect USB 3 0 devices to USB 3 0 ports for faster and better performance from your USB 3 0 devices H DVI D port This port is for any DVI D compatible device DVI D can t be converted to output RGB Signal to CRT and isn t compatible with DVI I 10 Serial port COM This port connects a modem or other devices that conform with serial specification 11 USB 2 0 ports 3 and 4 These two 4 pin Universal Serial Bus USB ports are for USB 2 0 1 1 devices Chapter 1 Product introduction 1 7 2 Internal connectors 1 CPU and chassis fan connectors 4 pin CPU FAN 3 pin CHA FAN Connect the fan cables to the fan connectors on the motherboard ensuring that the black wire of each cable matches the ground pin of the connector 1 IE ME Es m I Ei B EE mm K mm MM MEES CPU_FAN fi L CP
49. r 2 BIOS information 2 6 Boot menu The Boot menu items allow you to change the system boot options Select an item then press lt Enter gt to display the submenu Main Advanced Power Tools Exit Boot Settings Specifies the Boot Device Priority F sequence A virtual floppy disk drive Floppy Drive B k Boot Settings Configuration may appear when you set k Security the CD ROM drive as the first boot device ma Select Screen tl Select Item Enter Go to Sub Screen General Help Save and Exit ESC Exit v02 61 C Copyright 1985 2015 American Megatrends Inc 2 6 1 Boot Device Priority 1st xxth Boot Device These items specify the boot device priority sequence from the available devices The number of device items that appears on the screen depends on the number of devices installed in the system Configuration options Removable Dev Hard Drive ATAPI CD ROM Disabled L4 To select the boot device during system startup press F8 when ASUS logo appears To access Windows OS in Safe Mode press F8 after POST 2 6 2 Boot Settings Configuration Quick Boot Enabled Enabling this item allows the BIOS to skip some power on self tests POST while booting to decrease the time needed to boot the system When this item is set to Disabled BIOS performs all the POST items Configuration options Disabled Enabled Full Screen Logo Enabled Enables or disables the full screen logo display feature
50. rn on the system 2 Insert the support DVD to the optical drive or the USB flash drive that contains the BIOS file to the USB port 3 The utility automatically checks the devices for the BIOS file When found the utility reads the BIOS file and starts flashing the corrupted BIOS file 4 Turn off the system after the utility completes the updating process and turn on again V DO NOT shut down or reset the system while updating the BIOS Doing so can cause system bool failure Z Ensure to load the BIOS default settings to ensure system compatibility and stability Select Geng the Load Setup Defaults item under the Exit menu Refer to section 2 8 Exit menu for details ASUS M5A78L M LE USB3 2 3 2 4 2 2 BIOS setup program Use the BIOS Setup program to update the BIOS or configure its parameters The BIOS screens include navigation keys and brief online help to guide you in using the BIOS Setup program Entering BIOS Setup at startup To enter BIOS Setup at startup e Press lt Delete gt during the Power On Self Test POST If you do not press lt Delete gt POST continues with its routines Entering BIOS Setup after POST To enter BIOS Setup after POST Press lt Ctrl gt lt Alt gt lt Delete gt simultaneously e Press the reset button on the system chassis e Press the power button to turn the system off then back on Do this option only if you failed to enter BIOS Setup using the first two options U
51. sembly installation 1 6 L4 System memory E 1 8 1 4 1 er ON 1 8 1 4 3 Instelling KEE 1 9 15 Expansion SOUS U Es SE se RE saa 1 10 To PEGET x RE 1 12 L7 oes OE OE OE EE N 1 13 1 7 2 Internal connectors esse Eie EG NE n Gee eN 1 15 18 Software sUDDOLTL R III III ee Ne ie eeu Ge ee we Ee 1 20 1 8 2 Support DVD information sese 1 20 Chapter 2 BIOS information 2 1 Managing and updating your BIOS eese 2 1 2 1 1 ASUS Update utility 2 1 2 1 2 ASUS EZ Flash 2 e 2 2 2 1 3 ASUS CrashFree BIOS 3 Ee AE Ge Ee ee Ee AE ee Ee AE 2 3 22 BIOS setup program ia IILI GR GE ed AN OE sd we ie EE 2 4 2 2 1 BIOS menu screen NG GE Re ee ee de ks 2 5 2 2 2 de GE OE EE OE ER EE 2 5 2 2 3 Navigation kes uuu u u ER EE DE ee GE ee ie Ee Red 2 5 2 2 4 Ee UN EE uu s ER EE 2 6 2 2 5 Submenu items ses ENG ER ee aum eu OES RA ie 2 6 2 2 6 eru le le Mein ie u uu u uU Uu N EE 2 6 2 2 7 OUD WINN M 2 6 2 2 8 ve ic RE N 2 6 2 2 9 General help T M 2 6 CHEM gg EE EE RE EE RE aap 2 7 2 3 1 System Time DOCOCXX is pos reto BE ie GE SE ek ee 2 7 2 3 2 System Date Day xx xx xxxx esee 2 7 2 3 3 EE E
52. sing the power button reset button or the lt Ctrl gt lt Alt gt lt Del gt keys to force reset from a running operating system can cause damage to your data or system We recommend that you always shut down the system properly from the operating system A e The default BIOS settings for this motherboard apply to most conditions to ensure optimum performance If the system becomes unstable after changing any BIOS settings load the default settings to ensure system compatibility and stability Select the Load Setup Defaults item under the Exit menu See section 2 8 Exit Menu e The BIOS setup screens in this chapter are for reference only They may not exactly match what you see on your screen e Visit the ASUS website at www asus com to download the latest BIOS file for this motherboard Chapter 2 BIOS information 2 2 1 BIOS menu screen Menu items Menu bar Configuration fields General help M5A78L M LE USB3 BIOS Setup Version 0211 Advanced Power Boot Tools Exit u rrrs O V oQn h A ws Use ENTER TAB kes 34 30 or SHIFT TAB to System Date Thu 2 20 2014 select a field SATA3G 1 Not Detected Use or to SATA3G 2 Not Detected configure system SATA3G 3 Not Detected Time SATA3G 4 Not Detected SATA Configuration System Information Select Screen Select Item Change Field Select Field General Help Save and Exit Exit v02 61 C Copyright 1985 2015 American Megatrends Inc
53. so it stays on even when the PC is turned off When you select this option a confirmation window appears Select OK to save changes and exit Exit amp Discard Changes Select this option only if you do not want to save the changes that you made to the Setup program If you made changes to fields other than System Date System Time and Password the BIOS asks for a confirmation before exiting Discard Changes This option allows you to discard the selections you made and restore the previously saved values After selecting this option a confirmation appears Select OK to discard any changes and load the previously saved values Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus When you select this option or if you press lt F5 gt a confirmation window appears Select OK to load default values Select Exit amp Save Changes or make other changes before saving the values to the non volatile RAM ASUS M5A78L M LE USB3 2 23 2 24 Chapter 2 BIOS information Appendices Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class
54. ss lt Enter gt twice The message Password uninstalled appears aN If you forget your BIOS password you can clear it by erasing the CMOS Real Time Clock RTC RAM See section 1 6 Headers for information on how to erase the RTC RAM 2 20 Chapter 2 BIOS information After you have set a supervisor password the other items appear to allow you to change other security settings User Access Level Full Access This item allows you to select the access restriction to the Setup items Configuration options No Access View Only Limited Full Access No Access prevents user access to the Setup utility View Only allows access but does not allow change to any field Limited allows changes only to selected fields such as Date and Time Full Access allows viewing and changing all the fields in the Setup utility Change User Password Select this item to set or change the user password The User Password item on top of the screen shows the default Not Installed After you set a password this item shows Installed To set a User Password 1 Select the Change User Password item and press lt Enter gt 2 On the password box key in a password containing up to six letters or numbers or both then press lt Enter gt 3 Confirm the password when prompted The message Password Installed appears after you set your password successfully To change the user password follow the same steps as in setting a user password Cle
55. st uonersdO satt DOA 201 Jo ST Hed tan serduroo IAAP sn uoneurioju Aieju ounddns s1ojerpesr Teuopua q uedqns s1 ed OO4 DX suongouroods Surxo oJj 20 0 surtojJuoo egsn 31 W I84VSW 49quunN I8 pON pieoqi u oN SWUEN J9npoid jonpoJd oy yey so1e oop Agereg SSSt 809 01S LLL 6 L 0IS ON XEA SU0Ud 6 Sr6 VO Mowag Av AA 9j amp 10d 107 008 ssoJppy euoneugoju 19jnduro snsy MEN Aed a qQIsuodsay 9 LLOT 7 uonoos z MEd DOA Jod ALIINUOANOD TO NOLLVAYVID AG Appendices A 6
56. t all power cables from the existing system before you add a device Before connecting or removing signal cables from the motherboard ensure that all power cables are unplugged Seek professional assistance before using an adapter or extension cord These devices could interrupt the grounding circuit Ensure that your power supply is set to the correct voltage in your area If you are not sure about the voltage of the electrical outlet you are using contact your local power company If the power supply is broken do not try to fix it by yourself Contact a qualified service technician or your retailer Operation safety Before installing the motherboard and adding devices on it carefully read all the manuals that came with the package Before using the product ensure all cables are correctly connected and the power cables are not damaged If you detect any damage contact your dealer immediately To avoid short circuits keep paper clips screws and staples away from connectors slots sockets and circuitry Avoid dust humidity and temperature extremes Do not place the product in any area where it may become wet Place the product on a stable surface If you encounter technical problems with the product contact a qualified service technician or your retailer About this guide This user guide contains the information you need when installing and configuring the motherboard How this guide is organized This guide co
57. te performance level of the CPU fan Standard Sets to Standard to make the CPU fan automatically adjust depending on the CPU temperature Silent Sets to Silent to minimize the fan speed for quiet CPU fan operation Turbo Set to Turbo to achieve maximum CPU fan speed Manual Allows you to individually set the CPU fan parameters Z The following four items appear only when you set CPU Q Fan Mode to Manual CPU Upper Temperature 70 C 158 F Allows you to select the CPU upper temperature Configuration options 30 C 86 F 40 C 1 04 F 50 C 122 F 60 C 140 F 70 C 158 F 80 C 176 F 90 C 194 F ASUS M5A78L M LE USB3 2 17 CPU Fan Max Duty Cycle 100 Allows you to select the maximum CPU fan duty cycle When the CPU temperature reaches the upper limit the CPU fan will operate at the maximum duty cycle Configu ration options 20 80 40 50 60 70 80 90 100 CPU Lower Temperature 20 C 68 F Displays the lower limit of the CPU temperature CPU Fan Min Duty Cycle 20 Allows you to select the minimum CPU fan duty cycle When the CPU temperature is under 40 C the CPU fan will operate at the minimum duty cycle Configuration options 00 10 20 30 40 50 60 70 80 90 100 2 5 6 Anti Surge Support Enabled Allows you to enable or disable the Anti Surge protection feature Configuration options Disabled Enabled 2 18 Chapte
58. the PSU has a minimum power rating of 300W The system may become unstable or may not boot up if the power is inadequate DO NOT forget to connect the 4 pin ATX 12V power plug Otherwise the system will not boot up We recommend that you use a PSU with higher power output when configuring a system with more power consuming devices or when you intend to install additional devices The system may become unstable or may not boot up if the power is inadequate If you are uncertain about the minimum power supply requirement for your system refer to the Recommended Power Supply Wattage Calculator at http support asus com PowerSupplyCalculator PSCalculator aspx SLanguage en us for details Chapter 1 Product introduction 3 Serial ATA 3 0 Gb s connectors 7 pin SATA3G 1 4 These connectors are for the Serial ATA 3 0 Gb s signal cables for Serial ATA hard disk drives and optical disc drives If you installed Serial ATA hard disk drives you can create a RAID 0 RAID 1 RAID 10 and JBOD configuration through the onboard controller VG SATA3 O SATA3G 2 SATA3G 3 SATA3G_4 3 3 RSATA RXP1 RSATA RXN1 RSATA TXN1 RSATA TXP1 RSATA RXP2 RSATA RXN2 RSATA TXN2 RSATA TXP2 RSATA RXP RSATA RXN RSATA TXNS RSATA TXP3 RSATA TXN4 RSATA TXP4 GND GND GND GND GND GND GND M5A78L M LE USB3 SATA 3 0Gb s connectors A These connectors are set to IDE mode by default If you i
59. to save your CMOS settings in the Save to sub item Load CMOS Profiles Allows you to load the previous BIOS settings saved in the BIOS Flash Press lt Enter gt to load the file Start O C Profile Allows you to run the utility to save and load CMOS Press lt Enter gt to run the utility e This function can support devices such as a USB flash disk with FAT 32 16 format and single partition only DO NOT shut down or reset the system while updating the BIOS to prevent the system boot failure We recommend that you update the BIOS file only coming from the same memory CPU configuration and BIOS version Only the CMO file can be loaded Chapter 2 BIOS information 2 8 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items and save or discard your changes to the BIOS items M5A78L M LE USB3 BIOS Setup Version 0211 Exit Options Exit system setup m after saving the cahnges Exit amp Discard Changes F10 key can be used Discard Changes for this operation Load Setup Defaults K Pressing lt Esc gt does not immediately exit this menu Select one of the options from this menu or lt F10 gt from the legend bar to exit Exit amp Save Changes Once you are finished making your selections choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM An onboard backup battery sustains the CMOS RAM
60. ucts batteries other components as well as the packaging materials Please go to http csr asus com english Takeback htm for detailed recycling information in different regions Google License Terms Copyright 2014 Google Inc All Rights Reserved Licensed under the Apache License Version 2 0 the License you may not use this file except in compliance with the License You may obtain a copy of the License at http www apache org licenses LICENSE 2 0 Unless required by applicable law or agreed to in writing software distributed under the License is distributed on an AS IS BASIS WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND either express or implied See the License for the specific language governing permissions and limitations under the License ASUS M5A78L M LE USB3 English AsusTek Inc hereby declares that this device is in compliance with the essential requirements and other relevant provisions of CE Directives Please see the CE Declaration of Conformity for more details Fran ais AsusTek Inc d clare par la pr sente que cet appareil est conforme aux crit res essentiels et autres clauses pertinentes des directives europ ennes Veuillez consulter la d claration de conformit CE pour plus d informations Deutsch AsusTek Inc erkl rt hiermit dass dieses Ger t mit den wesentlichen Anforderungen und anderen relevanten Bestimmungen der CE Richtlinien bereinstimmt Weitere Einzelheiten entnehm
61. umple los requisitos b sicos y otras disposiciones relevantes de las directivas de la CE Consulte la Declaraci n de conformidad de la CE para obtener m s detalles Svenska AsusTek Inc f rklarar h rmed att denna enhet r i verensst mmelse med de grundl ggande kraven och andra relevanta best mmelser i CE direktiven Se CE f rs kran om verensst mmelse f r mer information Ykpa ncska AsusTek Inc sasBae mo Wel npucrpiit BITIOBI IAC OCHOBRUM BHMOraM Bi moBijux JIupekrusa C Bynp nacka app One nonpo6uup y Jleroraparii Biymosi tocri HopMaM EC T rk e AsusTek Inc bu ayg t n temel gereksinimlerle ve CE Y nergelerinin di er ilgili ko ullar yla uyumlu oldu unu beyan eder Daha fazla ayr nt i in l tfen CE Uygunluk Beyan na bak n Bosanski AsusTek Inc ovim potvr uje da je ovaj ure aj uskla en s osnovnim zahtjevima i drugim relevantnim propisima Direktiva EK Za vi e informacija molimo pogledajte Deklaraciju o uskla enosti EK Appendices ASUS contact information ASUSTeK COMPUTER INC Address 15 Li Te Road Peitou Taipei Taiwan 11259 Telephone 886 2 2894 3447 Fax 886 2 2890 7798 E mail info Q asus com tw Web site WWW asus com com Technical Support Telephone 86 21 38429911 Fax 86 21 5866 8722 ext 9101 Online support http www asus com tw support ASUS COMPUTER INTERNATIONAL America Address 800 Corporate Way Fremont CA 94539 USA Telephone 1 510 739
62. vedsaklige krav og andre relevante forskrifter i CE direktiver Du finner mer informasjon i CE samsvarserkl ringen Polski Niniejszym AsusTek Inc deklaruje e to urz dzenie jest zgodne z istotnymi wymaganiami oraz innymi powi zanymi zaleceniami Dyrektyw CE W celu uzyskania szczeg w sprawd Deklaracj zgodno ci CE Portugu s A AsusTek Inc declara que este dispositivo est em conformidade com os requisitos essenciais e outras disposi es relevantes das Diretivas da CE Para mais detalhes consulte a Declara o de Conformidade CE Rom n Prin prezenta AsusTek Inc declar faptul c acest dispozitiv respect cerin ele esen iale si alte prevederi relevante ale directivelor CE Pentru mai multe detalii consulta i declara ia de conformitate CE Srpski AsusTek Inc ovim izjavljuje da je ovaj ure aj u saglasnosti sa klju nim zahtevima i drugim relevantnim odredbama CE Direktiva Molimo vas pogledajte CE Deklaraciju o uskla enosti za vi e detalja Slovensky Spolo nos AsusTek Inc t mto prehlasuje e toto zariadenie vyhovuje pr slu n m po iadavk m a dal m s visiacim ustanoveniam smern c ES Viac podrobnost si pozrite v prehl sen o zhode ES Sloven ina AsusTek Inc tukaj izjavlja da je ta naprava skladna s temeljnimi zahtevami in drugimi relevantnimi dolo ili direktiv CE Za ve informacij glejte Izjavo CE o skladnosti Espa ol Por la presente AsusTek Inc declara que este dispositivo c

M5A78L-M LE/USB3

Contents

Download Pdf Manuals

Related Search

Related Contents