4.0 Amp VS Orbital Jig Saw Operator`s Manual
Contents
1. largely a matter of operator experience and experimentation on scrap The chart shown below is intended as a guideline only Position Cutting Action Applications 0 Straight line For clean cuts in wood and plywood For cutting mild steel stainless steel and plastics I Small orbit For cutting mild steel aluminum and hard wood Il Medium orbit For cutting wood and plywood HI Large orbit For fast aggressive cutting in wood and plywood INSTALLING OR REMOVING SAW BLADE CAUTION Always be sure that the tool is switched off and unplugged before performing any work or adjustments on the tool Always clean out all chips or foreign matter adhering to the blade and or blade holder Failure to do so may cause insufficient tightening of the blade resulting in a serious personal injury Do not touch the blade or the workpiece immediately after operation they may be extremely hot and could burn your skin Always secure the blade firmly Insufficient tightening of the blade may cause blade breakage or serious personal injury To install the blade 1 Position the chip deflector to allow access to the Blade Collet 2 Open the Blade collet by rotating the Spring Loaded Collet Lever clockwise 3 With the blade teeth facing forward insert the blade into Pa J J the blade collet as far as it will go ki 4 Check to make sure the back edge of the blade is positioned a gt a fe properly in the groove of the roller guide 5 Rel2. best to practice plunge cutting on scrap wood so the operator becomes familiar with the technique and determines the blade speed and orbital settings that work best 1 Set the speed at 5 or 6 and orbital setting to III 2 Tilt the tool up on the front edge of the base with the blade point positioned just above the workpiece surface 3 Make sure the blade is in the area to be cut 4 Apply downward pressure to the tool so that the front edge of the base will not move when you turn on the tool 5 Turn on the tool and gently lower the back end of the saw until the blade contacts the work surface 6 As the blade pierces the workpiece slowly lower the base of the tool down onto the workpiece surface until it is in the normal cutting position 7 Complete the cut in the normal manner VACUUM ATTACHMENT Your Jig Saw comes with a vacuum attachment This attachment allows you to connect it to a standard 1 1 4 vacuum hose To connect the Vac Attachment to the tool align the two tabs on the narrow end of the vac attachment with the corresponding slots on the back of the jig saw just below the power cord restraint WARNING Wear safety glasses Wear a dust mask if operation is dusty Wear hearing protection during long periods of operation Support and clamp work piece securely Keep your balance and don t overreach 1 Variable Speed Dial 2 LED Laser Switch 3 Tool Less Blade Collet 4 Adjustable Shoe 5 Ergonomically Designed Ha
3. dh Add NERI 4 0 Amp VS Orbital Jig Saw Operator s Manual 4 0 Amp Variable Speed Orbital Jigsaw Operator s Manual Specifications e Model AJS40 e Input 120 Volts AC 4 0 Amp e Variable Speed 500 3 000 SPM e Variable Speed Switch 6 Settings e Orbital Settings 4 e Work Light LED e Cutting Guide Laser Line e Dust Blower Switchable e Base Bevel 0 45 degrees Left and Right e Blade Type T Shank e Net weight 4 2 Ibs Laser Class II Laser Product Wavelength 650 nm Max Output lt 1 0 mW Complies with FDA21 CFR Parts 1040 10 and 1040 11 Runs on two AAA Batteries Included Two Year Warranty Kit includes Jigsaw 1 1 4 Vac Adaptor 2 Blades Hex Wrench and Case A WARNING To reduce the risk of injury user must read and understand this operator s manual before operating this tool Save this Manual for future reference Toll Free Help Line 1 888 552 8665 A WARNING WEAR YOUR The Operation of any power tool can result in foreign objects being Cree thrown into your eyes which can result in severe eye damage Before beginning tool operation always wear safety goggles Va or safety glasses with side shields and a full face shield when RO cis 8 93 8 needed We recommend Wide Vision Safety Mask for use over ANCES eyeglasses or standard safety glasses with side shields Always wear eye protection which is marked to comply with ANSI Z87 1 Look for this symbol to point out important sa
4. ds are for denser materials and faster speeds for soft materials Saw blade life is also largely determined by the motor speed and the type of material being cut The following chart is intended as a guideline only test cuts in scrap should be performed first to determine the best speed setting DAN APPRENTICE 0 Amp Variable Speed Orbital Jig Saw Operators Manual AJS40 Workpiece being cut Adjusting dial number Wood 4 6 Mild Steel 3 6 Stainless Steel 3 4 Aluminum 3 6 Plastics 1 4 The speed adjusting dial can be turned only as far as 6 and back to 1 Do not force it past 6 or 1 doing so may cause the speed adjusting function to no longer function properly SELECTING THE ORBITAL CUTTING ACTION This jigsaw can be operated in the conventional straight line up and down mode or with an orbital cuttin action During orbital cutting the blade is thrust forward on the upward cutting stroke greatly increasing cutting speed During the down stroke the blade is cleared of accumulated debris enhancing cutting efficiency and extending blade life by causing the blade to run cooler The orbital action adjustment switch is located on the lower left hand portion of the motor housing near the chip deflector The motor housing is marked 0 Il Ill The O designates the straight line mode I through Ill designate increasing levels of orbital action Just as with blade speed selecting the proper orbital action is
5. e workpiece and align the blade with the previously drawn guideline Make sure the blade does not contact the workpiece Turn the saw on wait for the blade to attain full speed and slowly move the blade into the workpiece Apply only enough downward pressure to keep the saw steady on the workpiece and only enough forward pressure to keep the blade cutting BEVEL CUTTING CAUTION Always be sure that the tool is switched off and unplugged before tilting the base Raise the chip shield all the way before making bevel adjustments and cuts To bevel or tilt the saw base turn the saw over so the base is facing upward and locate the bolt that secures the base to the saw Loosen the bolt in the base with the hex key provided Tilt the base until the desired bevel angle is obtained then tighten the bolt to secure the base in place INTERIOR CUTOUTS An interior cutout is needed when a cutting pattern is located in the workpiece without a lead in cut from an edge These cuts can be performed using one of two methods either using starting holes or by plunge cutting Using starting holes Within the cutout pattern pre drill one or more holes larger then saw blade being used Then insert the blade through the hole s to start your cut DAN APPRENTICE 0 Amp Variable Speed Orbital Jig Saw UN Operators Manual AJS40 Plunge cutting When using the plunge cutting method a starting hole or lead in cut from the workpiece edge is not necessary It is
6. ease the Collet Lever The blade should is now secured in the Blade Collet 6 Lower the chip shield completely To remove the blade follow the installation procedure in reverse CHIP SHIELD CAUTION Always cut with the Chip Shield down and hold the base flush with the workpiece Failure to do so may cause blade breakage resulting in a serious injury DUST BLOWER Your Jig Saw is equiped with a blower that directs air flow to the cutting area This feature provide a stream of air that keeps the dust away from the cut line improving visibility This feature can be turned OFF by rotating the blower switch to the vertical position To turn the Blower Feature ON turn the blower switch to the horizontal position GENERAL CUTTING CAUTION Always hold the base flush with the workpiece Failure to do so may cause blade breakage resulting in a serious injury Advance the tool very slowly when cutting curves or scrolling Forcing the tool may cause a slanted cutting surface and blade breakage Jig saws cut on the upstroke causing the workpiece surface facing upwards to splinter Therefore determine the good side of your work piece and place your guidelines for cutting on the opposite side Properly support and clamp the workpiece with the good side down and with the guidelines clearly visible and unobstructed above amp below the surface to be cut To start the cut place the front edge of the saw base on th
7. fety precautions It means attention Your safety is involved APPRENTICE 4 9 Amp Variable Speed Orbital Jig Saw Operators Manual AJS40 GENERAL SAFETY RULES WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e lead from lead based paints e crystalline silica from bricks and cement and other masonry products and e arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles A WARNING READ AND UNDERSTAND ALL WARNINGS CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS 1 READ THE INSTRUCTION MANUAL BEFORE OPERATING THE MACHINE To minimize the possible occurrence of accidents and personal injury learn the tool s application limitations and specific potential hazards peculiar to this tool 2 WEAR EYE AND HEARING PROTECTION ALWAYS USE SAFETY GLASSES WITH SIDE SHIELDS Unless otherwise specified everyday gla
8. hen performing an operation where cutting tools may contact hidden wiring or its own cord Contact with a live wire will make exposed metal parts of the tool live and shock the operator DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT GAINED FROM REPEATED USE REPLACE STRICT ADHERENCE TO JIG SAW SAFETY RULES IF YOU USE THIS TOOL UNSAFELY OR INCORRECTLY YOU CAN SUFFER SERIOUS PERSONAL INJURY 1 HOLD TOOL BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOLS MAY CONTACT HIDDEN WIRING OR ITS OWN CORD CONTACT WITH A LIVE WIRE WILL MAKE EXPOSED METAL PARTS OF THE TOOL LIVE AND SHOCK THE OPERATOR 2 ALWAYS USE SAFETY GLASSES OR GOGGLES ORDINARY EYE GLASSES ARE NOT SAFETY GLASSES 3 AVOID CUTTING NAILS INSPECT WORKPIECE FOR ANY NAILS AND REMOVE THEM BEFORE OPERATION 4 DO NOT CUT HOLLOW PIPE 5 CHECK FOR THE PROPER CLEARANCE BEYOND THE WORKPIECE BEFORE CUTTING SO THAT THE BLADE WILL NOT STRIKE THE FLOOR WORKBENCH ETC 6 HOLD THE TOOL FIRMLY 7 MAKE SURE THE BLADE IS NOT CONTACTING THE WORKPIECE BEFORE THE SWITCH IS TURNED ON 8 KEEP HANDS AWAY FROM MOVING PARTS 9 DO NOT LEAVE THE TOOL RUNNING OPERATE THE TOOL ONLY WHEN HAND HELD 10 ALWAYS SWITCH OFF AND WAIT FOR THE BLADE TO COME TO A COMPLETE STOP BEFORE REMOVING FROM THE WORKPIECE 11 DO NOT TOUCH THE BLADE OR THE WORKPIECE IMMEDIATELY AFTER OPERATION THEY MAY BE EXTREMELY HOT AND COULD BURN YOUR SKIN 12 Some mater
9. hine is tipped or if you should unintentionally contact the cutting tool DO NOT FORCE THE TOOL The tool will perform the job better and safer at the feed rate for which it was designed Forcing the tool could possibly damage the machine and may result in personal injury FEED THE WORK PIECE IN THE CORRECT DIRECTION AND SPEED Feed the work piece into a blade cutter or abrasive surface against the direction of the cutting tool s direction of rotation only Incorrectly feeding the work piece in the same direction as the cutting tool rotates causes the work piece to be thrown out at high speed NEVER LEAVE THE TOOL RUNNING UNATTENDED TURN THE POWER OFF Don t leave the machine until it comes to a complete stop TURN THE MACHINE OFF AND DISCONNECT THE MACHINE FROM THE POWER SOURCE before adjusting or changing set ups or when making repairs An accidental start up may occur causing personal injury NEVER USE THE TOOL IN AN EXPLOSIVE ATMOSPHERE Normal sparking of the motor could ignite fumes KEEP THE TOOL DRY CLEAN AND FREE FROM OIL AND GREASE Always use a clean cloth when cleaning Never use brake fluids gasoline petroleum based products or any solvents to clean the tool 27 DO NOT USE THE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF Have defective switches replaced by an authorized service center 28 USE ONLY CORRECT BLADES Do not use blades with incorrectly sized arbor holes Never use blade washers or blade bolt
10. ial contains chemicals which may be toxic Take caution to prevent dust inhalation and skin contact Follow material supplier safety data SAVE THESE INSTRUCTIONS AX WARNING MISUSE or failure to follow the safety rules stated in this Operator s manual may cause serious personal injury q APPRENTICE 4 9 Amp Variable Speed Orbital Jig Saw Operators Manual AJS40 OPERATION WARNING Always check that the power supply corresponds to the voltage on the rating name plate SWITCH ACTION WARNING Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool Switch can be locked in ON position for ease of operator comfort during extended use Use caution when locking tool in ON position and maintain a firm grasp on the tool Your jig saw is equipped with an on off switch trigger which is operated by squeezing or releasing Your jig saw is also equipped with a Lock On button located on the left side of the saw s handle just above the switch trigger Using the Lock On button allows the saw to be run continuously without the operator having to constantly apply pressure to the switch trigger To start the tool simply pull the switch trigger To stop the tool release the switch trigger Using with the Lock On button To start the tool and run the tool continuously pull the switch trigger then push in the Lock On button and release the s
11. ing dial located on the upper forward portion of the saw s handle Tool speed can be infinitely adjusted between 500 and 3 000 strokes per minute by rotating the adjusting dial Speed indicators appear on the dial as the numbers 1 through 6 1 is the slowest saw speed and number 6 represents the highest speed Therefore when the dial is rotated towards number 6 speed increases lower speed is obtained when the dial is rotated in the direction of number 1 The speed adjusting dial can be operated while the saw is running or when the saw is not operating The operator has the ability to preset the saw s speed by rotating the dial to the desired setting and then fully depressing the switch trigger urning the saw on for use Please note regardless of pressure applied on the trigger the tool will not operate any faster than the maximum speed setting selected Be aware that when the jigsaw is operated at low speed the motor temperature will begin to rise due to the slower speed of the internal cooling fan In such cases it is necessary to occasionally run the tool at full speed for a few minutes to aid internal cooling to keep the motor operating at high efficiency The jigsaw cutting speed or stroke rate required depends on the material being cut the type of blade being used and the feed rate used by the operator The best speed for a particular application is largely based on operator experience or experimentation However as a general rule slower spee
12. ire the greater the capacity of the cord For example a 14 gauge cord can carry a higher current than a 16 gauge cord When using more than one extension cord to make up the total length be sure each cord contains at least the minimum wire size required If you are using one extension cord for more than one tool add the nameplate amperes and use the sum to determine the required minimum wire size Guidelines for Using Extension Cords e If you are using an extension cord outdoors be sure it is marked with the suffix W A W in Canada to indicate that it is acceptable for outdoor use e Be sure your extension cord is properly wired and in good electrical condition Always replace a damaged extension cord or have it repaired by a qualified person before using it e Protect your extension cords from sharp objects excessive heat and damp or wet areas Recommended Minimum Wire Gauge for Extension Cords 120 Volt Nameplate Extension Cord Length Amperes De ju je a sa asso 4 sm 4 4 e 0 ro uu e mw es e Ca e pop E De fo fo ooo SPECIFIC SAFETY RULES FOR JIG SAWS WARNING DO NOT allow familiarity with the Jig Saw from repeated use replace strictly following all operating rules If the tool is used unsafely or incorrectly you or a bystander can suffer serious personal injury WARNING Hold tool by insulated gripping surfaces w
13. lective surfaces could direct the beam back toward the operator USING THE LED WORK LIGHT The tool is designed so that either the Laser Guide or the Work Light can be turned on at one time Both cannot be used simaltaniously The work light is an added source of light to better illuminate the work area Never use the work light as the only source of light Illuminate your work area enough to eliminate shadows on your work piece REPLACING LASER WORK LIGHT BATTERIES After extended use it will be neccessary to replace the two AAA batteries located in the light control housing To remove the light control housing simply push up on the housing as illustrated in the photo A Photo B shows the inside of the light control housing and the battery compartment The Batteries are installed as illustrated in the battery drawing To re attach the light control housing position the light control housing as illustrated in photo A while aligning the tabs and slide it back down into place The Light Control Housing can only be put on one way It must sit flush to the tool body to be installed correctly WARNING Make sure the Light Control House is securely in place before opporating the Jig Saw Failure to do so could cause the Light Control Housing to fall off while opperating the tool This could result in damaging the Tool Light control housing and your work piece SPEED ADJUSTMENT DIAL Your jigsaw is equipped with a speed adjust
14. mage to the machine and or personal injury may result APPRENTICE 0 Amp Variable Speed Orbital Jig Saw Operators Manual AJS40 16 17 18 19 20 21 22 23 24 25 26 USE RECOMMENDED ACCESSORIES Using accessories and attachments not recommended by the manufacturer or intended for use on this type tool may cause damage to the machine or result in personal injury to the user Consult the instruction manual for recommended accessories MAKE SURE YOUR EXTENSION CORD IS THE PROPER SIZE AND IS IN GOOD CONDITION When using an extension cord be sure to use one heavy enough to carry the current your product will draw An undersized cord will cause a drop in line voltage resulting in loss of power and tool overheating Consult the Extension Cord Chart for the correct size based on the cord length and nameplate ampere rating If ever in doubt use the next heavier wire gauge cord The smaller the gauge number the heavier the cord SECURE THE WORK PIECE Use clamps or a vise to hold the work piece when practical Using clamps or similar mechanical device is safer than using your hand s and allows you to use both hands to operate the tool Losing control of the work piece can cause personal injury DON T OVERREACH Maintain proper footing and balance at all times loss of balance can cause you to fall into the working machine possibly causing an injury NEVER STAND ON THE TOOL An injury may occur if the mac
15. ndle 6 Lock On Button 7 Dust Adaptor Port 8 Orbital Control Selector Two Year Warranty This product is warranted free from defects in material and workmanship for 2 years after date of purchase This limited warranty does not cover normal wear and tear nor damage from neglect or accident The original purchaser is covered by this warranty and it is not transferable Please return the tool to store location of purchase along with your receipt and you will receive a new tool for a refund THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES Toll Free Help Line For questions about this or any other APPRENTICE Product please call Toll Free 888 552 8665 TN APPRENTICE 4 9 Amp Variable Speed Orbital Jig Saw Operators Manual AJS40
16. s that are defective or incorrect 29 BEFORE MAKING A CUT BE SURE ALL ADJUSTMENTS ARE SECURE DOUBLE CHECK ALL SETUPS Make sure the blade is tight and not making contact with the saw or work piece before connecting to the power supply 30 AVOID CUTTING NAILS Inspect for and remove all nails from lumber before cutting 31 NEVER TOUCH THE BLADE OR OTHER MOVING PARTS DURING USE 32 NEVER START A TOOL WHEN ANY ROTATING COMPONENT IS IN CONTACT WITH THE WORK PIECE 33 MAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work 34 INSPECT TOOL CORDS PERIODICALLY If a damaged cord is found have it repaired by a qualified service technician at an authorized service facility The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor If repair or replacement of the electric cord or plug is required do not connect the equipment grounding conductor to a live terminal Repair replace damaged or worn cords immediately Be constantly aware of the cord location and keep it well away from the rotating blade 35 POLARIZED PLUGS To reduce the risk of electric shock this tool has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contac
17. sses provide only limited impact resistance they are NOT safety glasses Use only certified safety equipment eye protection equipment should comply with ANSI Z87 1 standards Protective hearing equipment should comply with ANSI 3 19 standards 3 DO NOT USE THIS OR ANY OTHER MACHINE WHEN YOU ARE TIRED UNDER THE INFLUENCE OF DRUGS ALCOHOL OR MEDICATION WATCH WHAT YOU ARE DOING STAY ALERT AND USE COMMON SENSE 4 WEAR PROPER CLOTHING Do not wear loose clothing gloves neckties rings bracelets wrist watches or other jewelry which may get caught in moving parts Wearing nonskid footwear is recommended as well as wearing protective hair covering to contain long hair 5 USE AND KEEP GUARDS IN PLACE and in good working order Never operate the machine with any guard or cover removed Check that all guards are in place secured and working correctly before each use to reduce the risk of injury 6 DO NOT USE THE TOOL IN DANGEROUS ENVIRONMENTS Keep the work area well lighted to prevent tripping or inadvertently placing arms hands or fingers in dangerous positions Do not use power tools in damp or wet locations or in the rain which can cause shock or electrocution 7 KEEP THE WORK AREA CLEAN Cluttered areas and benches invite accidents 8 CHECK THE TOOL FOR DAMAGED PARTS before using the machine Check for proper alignment of moving parts binding of moving parts component breakage and any other conditions that may affec
18. t a qualified electrician to install the proper outlet Do not change the plug in any way WARNING USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR OTHER AIRBORNE PARTICLES INCLUDING WOOD DUST CRYSTALLINE SILICA DUST AND ASBESTOS Direct particles away from face and body Always operate tool in a well ventilated area and provide for proper dust removal Use dust collection system wherever possible Exposure to the dust may cause serious and permanent respiratory or other injury including silicosis a serious lung disease cancer and death Avoid breathing the dust and avoid prolonged contact with H APPRENTICE 4 9 Amp Variable Speed Orbital Jig Saw Operators Manual AJS40 the dust Allowing dust to get into your mouth or eyes or lay on your skin may promote absorption of harmful material Always use properly fitting NIOSH OSHA approved respiratory protection appropriate for dust exposure and wash exposed areas with soap and water EXTENSION CORDS Grounded tools require a three wire extension cord Double insulated tools can use either a two or three wire extension cord As the distance from the power supply outlet increases you must use a heavier gauge extension cord Using extension cords with inadequately sized wire causes a serious drop in voltage resulting in loss of power and possible tool damage Refer to the table shown below to determine the required minimum wire size The smaller the gauge number of the w
19. t the tool s operation A guard or any other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury 9 REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING THE TOOL Keys wrenches scrap and other debris can be thrown at high speed possibly causing serious personal injury 10 KEEP CHILDREN AND VISITORS AWAY Your shop is a potentially dangerous environment and visitors should not be allowed to contact any tools extension cords or roam about unsupervised All visitors should wear safety glasses and be kept a safe distance from the work area 11 MAKE THE WORKSHOP CHILDPROOF by using padlocks master switches and by removing starter keys from tools 12 MAINTAIN ALL TOOLS AND MACHINES WITH CARE Keep tools sharp and clean for best and safest performance Follow instructions for lubricating and changing accessories 13 DISCONNECT TOOLS WHEN NOT IN USE before servicing or when changing attachments blades bits cutters etc 14 REDUCE THE RISK OF UNINTENTIONAL STARTING Check to be sure that the tool s switch is in the OFF position before plugging in the power cord Should a power failure occur move the switch to the OFF position Accidental start ups can cause serious personal injury 15 USE THE CORRECT TOOL FOR THE JOB Don t force the tool or attachment to do a job for which it was not designed Don t use the tool for a purpose not intended as da
20. witch trigger To unlock the switch pull the switch trigger fully and release it AWARN ING if the Lock On button is continuously being depressed the trigger cannot be released USING THE LASER GUIDE Only turn on the laser light on when the tool is on the work piece 1 First mark the line of cut on your work piece good side down 2 Insert plug into power source 3 Place the front edge of the saw foot on the work piece turn on the Laser Guide and align the beam with the line of cut 4 Hold tool firmly squeeze the trigger and allow the tool reach desired speed 5 Press down keeping the saw foot flat against the work piece TOM as you slowly push the saw forward keeping the Laser beam _ 4 Y on center with your cut line LED Laser Switch X Laser Light Y LED Light Z 6 After completing the cut Release the trigger and turn off the laser light AX WARNING LASER RADIATION AVOID DIRECT EYE EXPOSURE DO NOT stare into the laser light source Never aim light at another person or object other than the work piece Laser light can Damage your eyes A WARNING DO NOT use tintea glasses to enhance the laser light Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool A WARNING NEVER aim the Beam at a work piece with a reflective surface Bright shiny reflective sheet steel or similar reflective surfaces are not recommended with laser use Ref
Download Pdf Manuals
Related Search