Xerox (WNA-100) (097S03740) Network Adapter
Contents
1. This needs to be changed to the name of the wireless network that the WNA100 is being attached to If this is not changed to the correct wireless network name the name is case sensitive the wireless adapter will not configure correctly to the network e Encryption type for example WEP 64 bit WEP 128 bit or WPA Note Depending on the Encryption type other information such as the WEP Key or the WPA Pre Shared Key must also be obtained e Authentication type for example Open System Shared Key or PSK To configure the wireless settings l 2 After the above information has been obtained click on any of the links under the Wireless Configuration folder on the left side of the adapter s web interface The Login Required window will be displayed Enter the configuration password and then click on the Login button The Wireless Configuration window will be displayed Note The factory default configuration password is word access in lower case 3 Depending on the information obtained enter the required settings in the WEP WPA or EAP Settings section For example if the wireless router uses WEP 64 bit encryption enter the required information in the WEP section The following is an example of settings that need to be configured for the WNA 100 to connect to a wireless router Wireless Configuration Band 802 11b g M Network Type INFRASTRUCTURE Network Name S2. How To Set up and Configure the WNA 100 Wireless Network Adapter Section 1 Set up and Connect the Adapter to a Computer Then Configure the Computer to Communicate With the Adapter Before the adapter can be connected to a printer it must be connected to a computer so that it can be configured to function on a wireless network The adapter must be configured from the adapter s web interface using an Internet browser After the adapter has been connected to the computer the computer s TCP IP settings must be configured to communicate with the adapter To set up the adapter 1 Connect the antenna to the adapter 2 Connect the power supply cord to the adapter and then plug the power unit into the wall outlet Note Only use the power supply provided with the adapter 3 Connect one end of the supplied Ethernet crossover cable to the Ethernet port on the adapter 4 Connect the other end of the crossover cable to the Ethernet port on the computer that will be used to configure the adapter using an Internet browser Note The adapter is not intended for use on a switch or hub The adapter must be connected directly to the computer using the Ethernet crossover cable Make sure the computer is configured to use an IP address of 169 254 x x where the x characters represent a decimal number between 0 254 For example 169 254 111 113 If necessary contact the network System Administrator Open an Internet browser window 7 En
3. SID Wireless Network Adapter Encryption WEP 64 bit bl Authentication Open System oa WEP Settings WEP Key 1 WEP Keys Note For additional information about the various wireless settings displayed on the adapter s web interface click on the Help button at the top right of the web browser window Section 3 Configure the TCP IP Settings for the Wireless Router Management Note This solution requires knowledge of the TCP IP addressing scheme for wireless network that the WNA 100 is being installed to and may require the assistance of a network System Administrator TCP IP Configuration BOOTP DHCP Settings BOOTP DHCP Boot Timeout DHCP Server Address TCP IP Settings IP Address 169 254 111 111 Network Mask 255 255 0 0 Default Router 1 Click on any of the links under the TCP IP Configuration folder on the left of the adapter s web interface The TCP IP Settings window will be displayed 2 Select OFF from the BOOTP DHCP pull down menu 3 Enter an IP address network mask also known as subnet mask and default router in the fields provided under the TCP IP Settings section IP Address Enter an IP address for the adapter that is valid for the network in the format of X X X X Where the x characters represent a decimal number from 0 255 For example 192 168 0 105 Network Mask Enter a network mask for the adapter that is valid for the network in the format of X X X X where x characters repre
4. e Adapter to the Printer 1 Click on the Restart button in the Reset section on the Administrative Utilities window and then click on Confirm to reset the adapter so that all configuration settings will be saved Reset Interface Confirm reset Select Confirm to restart the interface The configuration parameters will not be changed Confirm Close Window Note Do not click the Reset button next to Reset to Factory Defaults This will cause all changes to be reset and they will need to be re entered This is only to be used if the wireless device needs to be reset to factory defaults 2 Disconnect the Ethernet crossover cable from the computer and then connect the cable to the printer s Ethernet port A Configuration Page will be printed Note The adapter can be attached to the printer by using the Mounting Kit that was shipped with the adapter Caution Do not attach the Wireless Adapter to the printer in a way that covers up the printer s air vents Damage to the printer can result by blocking the printer s air vents
5. sent a decimal number from 0 255 For example 255 255 255 0 Default Router Enter the IP address of the router Gateway that the adapter uses to communicate with the network in the format of x x x x where the x character represents a decimal number from 0 255 For example 192 168 0 100 4 If necessary configure any other settings displayed on the TCP IP settings window Note For additional information about the various settings click on the Help button at the top right of the web browser window Section 4 Configure the Wireless Adapter Administrative Utility Settings 1 Click on any of the links under the Administrative Utility Settings folder on the left side of the adapter s web interface The Administrative Utilities window will be displayed 2 Click on the Change button in the Configuration Interface section Configuration Interface 3 Select Wireless from the pull down menu and click Submit Configuration Interface Configuration Interface Submit Reset Form Close Window Note Setting the default configuration interface to wireless will allow access to the adapter s web interface after the adapter has been connected to the printer 4 If necessary configure any other administrative settings Note For additional information about the various administrative settings click on the Help button at the top right of the window Section 5 Reset the Adapter to Save All Settings Then Connect th
6. ter the IP address of the adapter in the Address field and then press Enter on the keyboard The adapter s home page Status window will be displayed Note The factory default IP address of the adapter is 169 254 111 111 Note If the adapter s home page is not displayed make sure to disable any browser proxy settings that have been configured The proxy settings can be enabled again after the adapter has been configured If necessary contact the network System Administrator Section 2 Configure the Wireless Settings To configure the wireless settings for the adapter the following information must be known about the wireless router that is set up on the network the WNA 100 is to going to be attached to This information is unique to each network If necessary contact the network System Administrator or the manufacturer of the wireless router to obtain this information or refer to the wireless router s user guide Without the network configuration for the wireless router the WNA 100 cannot be configured correctly for a wireless Ethernet connection e Frequency Band for example 802 11b or 802 1 1b g e Network Type AD HOC or Infrastructure Note If AD HOC is the network type the Channel must also be obtained The Channel will be a number between I and 11 e Network Name Secure Socket Identification SSID name of the wireless network Note By default the SSID name from the factory is set to Wireless Network Adapter
Download Pdf Manuals
Related Search