LG Flatron L1715S 17" LCD Monitor
Contents
1. Do not rub or strike the Active Matrix LCD with anything hard as this may scratch mar or damage the Active Matrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is characteristic of the tixed resolution LCD panel On Cleaning a Unplug the display before cleaning the face of the display screen Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock On Repacking a Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Unfolding the stand base 1 Lay the monitor on a cushion or piece of soft cloth with its front side facing upward 2 Grasp the stand firmly with both hands as shown in the picture and unfold the base by2. Return to all factory default settings except LANGUAGE If you don t want to reset the monitor use the lt q gt button to select NO and then press the SELECT AUTO button Troubleshooting Check the following before calling for service No image appears Is the power cord of the Check and see if the power cord is connected display connected properly to the power outlet Is the power indicator Press the Power button light on Is the power on and the Adjust the brightness and the contrast power indicator green Is the power indicator e If the display is in power saving mode try moving amber the mouse or pressing any key on the keyboard to bring up the screen e Make sure if the power is on e Try to turn on the PC Do you see an INPUT This message appears when the signal from the SIGNAL OUT OF PC video card is out of horizontal or vertical RANGE message on frequency range of the display See the the screen Specifications section of this manual and configure your display again Do you see a NO This message appears when the signal cable SIGNAL message on between your PC and your display is not the screen connected Check the signal cable and try again Do you see a CONTROLS LOCKED message on the screen Do you see e You can secure the current control settings CONTROLS LOCKED so that they cannot be inadvertently when you push MENU changed You can u
3. level Accept the changes by pressing the SELECT AUTO Button GCA WNW Exit the OSD by Pressing the MENU Button On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus Main menu Sub menu Reference BRIGHTNESS BRIGHTNESS o To adjust the brightness and CONTRAST CONTRAST g contrast of the screen COLOR PRESET 9300K gO To customize the color of the 6500K o screen R G B User Color GAMMA POSITION To adjust the position of the PHASE jo stability of the screen SETUP LANGUAGE lo To customize the screen status OSD POSITION le for a user s operating environment FACTORY RESET Adjustable NOTE he order of icons may differ depending on the model A8 A10 On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu NOTE a OSD On Screen Display menu languages on the monitor may differ from the manual To adjust the brightness and contrast of the screen OSD Adjust Description BRIGHTNESS CONTRAST O C BRIGHTNESS Cr 88 To adjust the brightness of the screen gt Do D O contrast To adjust the contrast of the screen To customize the color of the screen Description COLOR
4. Do not place the display on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer To Prevent Fire or Hazards a Always turn the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house Keep children from dropping or pushing objects into the display s cabinet openings Some internal parts carry hazardous voltages a Do not add accessories that have not been designed for this display a During a lightning storm or when the display is to be left unattended for an extended period of time unplug it from the wall outlet Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near water such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER a Block the bottom ventilation slots by placing the display on a bed sofa rug etc a Place the display in a built in enclosure unless proper ventilation is provided a Cover the openings with cloth or other material a Place the display near or over a radiator or heat source
5. Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential e shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service technician for replacement Do not Open the Display a here are no user serviceable components inside There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury
6. PRESET 9300K 6500K PRESET 9300K nee Select the screen color RED Ail e 9300K Slightly bluish white GREEN llllllllllll i 6500K Slightly reddish white BLUE lt illiiiilllll gt RED teats al ina ee i GREEN Set your own color levels BLUE GAMMA Set your own gamma value 50 50 On the monitor high gamma values display whitish images and low gamma values display high contrast images To adjust the position of the screen OSD Adjust Description POSITION Vertical Position Ex d To move image up and down a eag Horizontal Position To move image left and right On Screen Display OSD Selection and Adjustment To improve the clarity and stability of the screen OSD Adjust Description TRACKING CLOCK lililii gt PHASE lt I IIIIIIIII gt CLOCK PHASE To minimize any vertical bars or Stripes visible on the screen background The horizontal screen size will also change To adjust the focus of the display This item allows you to remove any horizontal noise and clear or sharpen the image of characters To customize the screen status for a user s operating environment OSD Adjust SETUP LANGUAGE gt ENGLISH OSD POSITION gt FACTORY RESET gt NO 1280x1024 60Hz PRESET MODE LANGUAGE OSD POSITION FACTORY RESET Description To choose the language in which the control names are displayed To adjust position of the OSD window on the screen
7. ative SOG Sync On Green Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7Vp 0 750hm Max VESA 1280 x 1024 75Hz Recommend VESA 1280 x 1024 60Hz DDC 2B Normal 40W Stand by Suspend lt 2W DPMS Off lt 2W Full Up Position Folded Position Width 38 6 cm 15 20 inches Height 37 2 cm 14 65 inches Depth 15 2 cm 5 98 inches Net 4 3 kg 9 48 Ibs Tilt 0 25 AC 100 240V 50 60Hz 1 0A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 95 non Condensing Attached O Detached Attached Detached O Wall outlet type or PC outlet type TOO99 38 6 cm 15 20 inches 40 2 cm 15 83 inches 6 6 cm 2 60 inches a Information in this document is subject to change without notice Specifications Preset Modes Resolution Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 VGA 640 x 350 31 469 70 2 VGA 720 x 400 31 468 70 3 VGA 640 x 480 31 469 60 4 VESA 640 x 480 37 500 75 5 VESA 800 x 600 37 879 60 6 VESA 800 x 600 46 875 75 7 MAC 832 x 624 49 725 75 8 VESA 1024 x 768 48 363 60 9 VESA 1024 x 768 60 123 15 10 MAC 1152 x 870 68 681 75 11 VESA 1152 x 900 61 805 65 12 VESA 1280 x 1024 63 981 60 13 VESA 1280 x 1024 79 976 75 VESA wall mounting Connected to another object stand type and wall mounted type This monitor accepts a VESA compliant mounting inte
8. l Controls MENU e W LightView A 4 amp D e SELECT AUTO Ss O Control Function 1 Power Button Use this button to turn the display on or off Power DPMS This Indicator lights up green when the display Indicator operates normally If the display is in DPM Energy Saving mode this indicator color changes to amber 2 MENU Button Use this button to enter or exit the On Screen Display VA lt gt Buttons Use these buttons to choose or adjust items in the On Screen Display SELECT AUTO Use this button to enter a selection in the On Screen Button Display Control Panel Functions Control Direct Access Function Y LightView A This function optimizes the brightness contrast or color value to LIGHT VIEW the surrounding conditions and settings and enables you to A enjoy the most suitable picture by adjusting the surroundings DAY NIGHT USER MODE PHOTO NGTT a e TEXT For viewing letters Seep ene e MOVIE For viewing movies e PHOTO For viewing pictures or the photographs e USER MODE This function memorizes the manual adjustment Brightness Contrast and Color value on the On Screen Display qa Bring up Contrast and Brightness adjustment lt P gt VA lt gt MENU O AUTO adjustment function When adjusting your display settings always press the PROCESSING SELECT AUTO button before entering the On Screen Display OSD This will automatically adjust your display image
9. l cable is properly connected and mono or abnormal use a screwdriver to fasten if necessary Make sure the video card is properly inserted in the slot Set the color setting higher than 24 bits true color at Control Panel Settings The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Make sure the power voltage is high enough It has to be higher than AC100 240V 50 60Hz Troubleshooting Have you installed the display driver Have you installed the e Be sure to install the display driver from the display driver display driver CD or diskette that comes with your display Or you can also download the driver from our web site http www lge com Do you see an e Make sure to check if the video card supports Unrecognized monitor Plug amp Play function Plug amp Play VESA DDC monitor found message Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight with tilt stand Tilt Range Power Input Environmental Conditions Tilt Stand Signal cable Power cord Regulations NOTE Specifications 17 inches 43 2cm Flat Panel Active matrix TFT LCD Anti Glare coating 17 inches viewable 0 26 mm pixel pitch Horizontal Freq 30 83kHz Automatic Vertical Freq 56 75Hz Automatic Input Form Separate TTL Positive Negative Composite TTL Positive Neg
10. nlock the OSD controls button at any time by pushing the MENU button and gt button for 3 seconds the message CONTROLS UNLOCKED will appear Troubleshooting Display image is incorrect Display Position is Press the SELECT AUTO button to automatically incorrect adjust your display image to the ideal setting lf the results are unsatisfactory adjust the image position using the H position and V position icon in the on screen display Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed If yes readjust the video card to the recommend resolution On the screen Press the SELECT AUTO button to automatically background vertical adjust your display image to the ideal setting bars or stripes are If the results are unsatisfactory decrease the visible vertical bars or stripes using the CLOCK icon in the on screen display Any horizontal noise Press the SELECT AUTO button to automatically appearing in any adjust your display image to the ideal setting image or characters If the results are unsatisfactory decrease the are not clearly horizontal bars using the PHASE icon in the on portrayed screen display Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color The screen color is Check if the signa
11. rface pad Kensington Security Slot optional Connected to a locking cable that can be purchased separately at most computer stores
12. swiveling it out y Folding the stand base 1 Lay the monitor on a cushion or piece of soft cloth with its front side facing downward 2 Grasp the stand firmly with two hands and rotate the base while pulling out its underside caution If you try to fold the stand base in any other way be careful to avoid catching your hand at the rear of the unit or you may sustain injury a Important a If the stand base is wrenched with excessive force when being folded or unfolded the monitor may be damaged Handle with care a Adjust the angle of the stand base holding the monitor screen with two hands Connecting the Display Using the Computer 1 Connect the signal cable When attached tighten the thumbscrews to secure the connection 2 Connect the power cord into a proper power outlet that is easily accessible and close to the display TMS NOTE a This is a simplified representation of the rear view pie f a This rear view represents a general model your display N Oe eel f may differ from the view as shown Analog signal D sub Varies according to model xwa Wall outlet type PC outlet type Wean L PC 4 4 T p gt Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector Control Panel Functions Front Pane
13. to the ideal settings for the current screen resolution size display mode The best display mode is 1280x1024 CONTROLS LOCKED UNLOCKED MENU and gt CONTROLS LOCKED This function allows you to secure the current control settings so that they cannot be inadvertently changed Press and hold CONTROLS UNLOCKED the MENU button and gt button for 3 seconds the message CONTROLS LOCKED appears You can unlock the OSD controls at any time by pushing the MENU button and button for 3 seconds the message CONTROLS UNLOCKED will appear On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD NOTE a Allow the display to stabilize for at least 30 minutes before making image adjustments To make adjustments in the On Screen Display follow these steps MENU Y A SELECT AUTO VA 4 gt MENU lt SELECT AUTO x Press the MENU Button then the main menu of the OSD appears To access a control use the W or A Buttons When the icon you want becomes highlighted press the SELECT AUTO Button Use the V A lt gt Buttons to adjust the item to the desired
Download Pdf Manuals
Related Search