LG Studioworks N2200P 22" CRT Monitor
Contents
1. Troubleshooting Do you see basic discoloration 16 colors Is the screen color unstable or monochrome Do you see two fine horizontal lines on the screen Do you see a partial blurring on the screen The screen color is not normal Set the color depth to 256 colors or higher use Control Panel gt Display Settings gt Color Palette e Check the connection of the signal cable Or pull out the video card of the PC and insert it again e Two fine horizontal lines may be visible on the screen This is not a fault or defect of the moitor and is normal for all aperture grille type displays The fine lines are the shadows of Damper Wires which are used to reduce the susceptibility of the CRT s aperture grille to shock or vibration This happens due to interference from surrounding magnetic fields as created when speakers steel structures or high voltage lines are placed near the monitor Remove any such materials from the immediate vicinity and use the DEGAUSS icon on the screen adjustment menu to fix the screen Do you see the after image even when you tum off the monitor I see an after image on the screen A premature aging of the monitor pixels may cause the prolonged display of a single image on the screen Be sure to use a screen saver to maximize the service life of the monitor Do you see the wave direct2. Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this monitor observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the monitor only from a power source indicated in the specifications of this manual or listed on the monitor If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service technician for replacement Do not Open the Monitor a There are no user serviceable components inside a There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the monitor is not operating properly To Avoid Personal In
3. MENU A Y SELECT A Y lt gt SELECT MENU a Case 2 OSD A Y SET A V4 gt SET OSD ii Press the MENU or OSD Button then the main menu of the OSD appears To access a control use the or W Buttons When the icon you want becomes highlighted press the SELECT or SET Button Use the amp W lt q p gt Buttons to adjust the item to the desired level Accept the changes by pressing the SELECT or SET Button Ge amp Y Exit the OSD by pressing the MENU or OSD Button On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus Main menu Sub menu Reference Brightness To adjust the brightness and contrast of the screen Ont Contrast V Position POSITION H Position To adjust the position of the screen han V Size To adjust the size of the screen H Size i Tilt To adjust the shape of the screen Side Pincushion S Pincushion Balance Parallelogram Trapezoid H Corner Top Corner Bottom Corner Recall Zoom H Linearity V Linearity Recall RIGB PRESET 6500K To customize the color of the COLOR 9300K screen Temp R G B User Color Adjustable NOTE a The order of icons may differ depending on the model A10 A14 On Screen Display OSD
4. a Place the monitor in a built in enclosure unless proper ventilation is provided a Cover the openings with cloth or other material a Place the monitor near or over a radiator or heat source On Cleaning a Unplug the monitor before cleaning the face of the monitor screen a Use a slightly damp not wet cloth Do not use an aerosol directly on the monitor screen because overspray may cause electrical shock On Repacking a Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material Connecting the Monitor Before setting up the monitor ensure that the power is turned off to the monitor computer system and other attached devices Carefully set the monitor face down with the underside facing you Connecting the Tilt Swivel stand 1 Align the hooks on the tilt swivel stand with the matching slots in the base of the monitor 2 Insert the hooks into slots 3 Slide the tilt swivel stand toward the front of the monitor until the latches click into the locked position NOTE a This illustration depicts the general model of connection Your monitor may differ from the items shown in the picture Latch Hook Connecting the Monitor Using the Computer 1 Connect the signal cable When mated tighten the thumbscrews to secure the connection 2 Connect the power cord into a p
5. 3cm 19 8 inches Height 50 9 cm 20 4 inches Depth 47 7 cm 18 8 inches Net 31 3 kg 69 0 lbs AC 100 240V 50 60Hz 2 0A Operating Conditions Temperature 5 C to 35 C Humidity 10 to 90 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Attached Detached O Attached or Detached TCO99 a Information in this document is subject to change without notice Specifications Preset Modes Resolution Horizontal Freq kHz Vertical Freq Hz Display Modes Resolution 1 VESA 640 x 480 2 VESA 800 x 600 3 VESA 1024 x 768 4 VESA 1024x768 5 VESA 1280 x 1024 6 VESA 1280 x 1024 7 VESA 1600 x 1200 8 VESA 1600 x 1200 9 VESA 2048 x 1536 31 47 53 68 60 02 68 68 79 98 91 15 93 75 106 25 121 95 60 85 75 85 75 85 75 85 75 Using the BNC connector with other types of video cards Using the BNC connectors with other types of video cards Follow the example that fits your needs 1 In case of using a composite sync on green video signal Sync On Green Connect each R G and B video signals to BNC receptacles on the back of the monitor Blue ow 2 Incase of using an external composite sync signal Connect each R G and B video signals and composite sync signal to the BNC receptacles on the rear panel Varies according to model 3 In case of using a separate horizontal and vertical
6. SIZE Vertical Size A 49 To adjust image height gt E 64 Pe f Horizontal Size p44 To adjust image width On Screen Display OSD Selection and Adjustment To adjust the shape of the screen OSD Adjust Description ObODOHB lt i lt i lt u Amim Hangoa miii eee JoOoOoo SHAPE lt i iii an00 rmn lt i lt i 2 z v yates Ct 7 youSes SHAPE A umn lt i mme This function is available for designated models only bod Tilt To correct image rotation Side Pincushion To correct a concave or convex bowing of the image Side Pincushion Balance To correct the balance of both sides bowing Parallelogram To correctly adjust the skew of the image Trapezoid To correct geometric distortion H Corner Top Corner Bottom Corner To correct an irregular distortion of the displayed image Recall You can use this function to reload the modified parameters for screen display operation as specified by the user after purchase Side Pincushion Side Pincushion Balance Parallelogram Trapezoid H Corner Top Corner Bottom Corner These recalled options may differ depending on the mode selected Preset User or New Zoom To simultaneously adjust horizontal and vertical size of the image To adjust the shape of the scree
7. adjustment The Contrast and Brightness functions are also available in the On Screen Display OSD menu lt q Button Brings up the clearness of the image letters pictures or moving pictures AR For seeing letters For seeing pictures or the photographs For seeing moving pictures O AUTO adjustment function When adjusting your display settings always press the AUTO button before entering the On Screen Display OSD This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode The best display mode is 1600 x 1200 E INPUT Use this button to make Dsub or BNC connector active This feature is used when two computers are connected to the display The default setting is Dsub The LED is turned on for the D sub connector and is turned off for the BNC connector On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the monitor is quick and easy with the On Screen Display Control system A short example is quick and easy given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD NOTE a Allow the monitor to stabilize for at least 30 minutes before making image adjustments To make adjustments in the On Screen Display follow these steps a Case 1
8. sync signal Connect each R G and B video signals and the horizontal and vertical sync signal to BNC receptacles on rear panel Varies according to model Gray NOTE a This package does not include the BNC connectors but you can purchase them at your local computer stores HD Horizontal Drive a This monitor does not support the DDC function if you use the VD Vertical Drive 5 BNC connectors with other types of video cards COMP Composite Making use of USB Universal Serial Bus USB Universal Serial Bus is an innovation in connecting your different desktop peripherals conveniently to your computer By using the USB you will be able to connect your mouse keyboard and other peripherals to your monitor instead of having to connect them to your computer This will give you greater flexibility in setting up your system USB allows you to connect a chain of up to 120 devices on a single USB port and you can hot plug attach them while the computer is running or unplug them while maintaining the Plug and the Plug auto detection and configuration This monitor has an integrated BUS powered USB hub allowing up to 4 other USB devices to be attached it USB connection 1 Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub using the USB cable Computer must have a USB port 2 Connect the USB compliant peripherals to the downstream ports of the monitor Th
9. DEGAUSS NATURAL COLOR AUTO SIZING SHARPNESS MOIRE PURITY CONVER GENCE To manually demagnetize the screen to avoid showing incorrect images or colors This is have the real color of the image This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode This is to adjust the clearness of the screen It is recommended to use this to see movies or moving picture This item allows you to reduce the degree of moire Moire is caused by interference Horizontal Scan Line with the periodical dot screen It is normally OFF H 0 V 0 The moire adjustments may affect the focus of the screen Moire adjustments may shake slightly while the moire reduction function is on Use to adjust the purity on the screen if the color appears uneven This is to adjust the alignment of red and blue fields Troubleshooting Check the following before calling for service No image appears Is the power cord of the Check and see if the power cord is connected properly to monitor connected the power outlet abi power indicator light Press the Power button on s the power on and the Adjust the brightness and the contrast power indicator green Is the power indicator Ifthe monitor is in power saving mode try moving the amber mouse or pressing any key on the keyboard to bring up the screen Do you see an OUT OF This mes
10. Selection and Adjustment Main menu Sub menu Reference Video Level To customize the screen status SETUP Language for a user s operating environment OSD Time OSD Position Reset J Clamp 3 Degauss To improve the clarity and spear Natural Color stability of the screen Auto Sizing J Sharpness Moire H Moire V Moire Purity Convergence Adjustable NOTE a The order of icons may differ depending on the model A10 A14 On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu To adjust the brightness and contrast of the screen OSD Adjust Description HERA AB BRIGHTNESS CONTRAST AN OR Brightness fon To adjust the brightness of the screen gt Q92 D Oo Contrast To adjust the contrast of the screen To adjust the position of the screen OSD Adjust Description E3 RIGB POSITION LA Vertical Position Eg To move image up and down E 66 rak E 45 e1 gt Horizontal Position x To move image left and right To adjust the size of the screen OSD Adjust Description
11. el The normal level used for most PCs is 0 7V If the screen becomes suddenly washed out or blurred please select 1 0V and try again To choose the language in which the control names are displayed OSD Menus are available in 11 languages English German French Spanish Italian Swedish Finnish Portuguese Korean Chinese and Russian Set the OSD time i e the length of time a menu will remain on screen before it shuts off automatically Adjust the time to 5 10 20 30 or 60 seconds OSD POSITION To adjust position of the OSD window on RESET CLAMP the screen Return to all factory default settings except LANGUAGE BRIGHTNESS CONTRAST Tilt Color 9300K Video Level OSD Time OSD Position Moire Convergence These reset options may differ depending on the mode selected Preset User or New In case of input SOG Sync On Green Video Signal the back raster will appear green Then to select the SOG Sync On Green in the clamp it goes back to the original back raster On Screen Display OSD Selection and Adjustment To improve the clarity and stability of the screen OSD Adjust Description SPECIAL DEGAUSS gt ON NATURAL COLOR gt OFF AUTO SIZING gt ON SHARPNESS gt v 93 6 kHz 75 0 Hz PRESET MODE SPECIAL A MOIRE gt PURITY gt CONVERGENCE gt it 93 6 kHz 75 0 Hz PRESET MODE This function is available for designated models only EOS
12. is is a simplified representation a This is a simplified representation ofthe rear view of the side view wi gt USB downstream Ports To USB downstream port connect the cables from USB of the USB compliant PC compliant peripherals such as or another hub cable keyboard mouse etc NOTE a To activate the USB hub function the monitor must be connected to a USB compliant PC OS or another hub with the USB cable enclosed a When connecting the USB cable check that the shape of the connector at the cable side matches the shape at the connecting side a Even if the monitor is in a power saving mode USB compliant devices will function when they are connected the USB ports both the upstream and downstream of the monitor Making use of USB Universal Serial Bus USB Specifications USB standard Rev 1 1 complied BUS powered hub Downstream power supply 500mA for each MAX Communication speed 12 Mbps full 1 5 Mbps low USB port 1 Upstream port 4 Downstream ports IMPORTANT These USB connectors are not designed for use with high power USB devices such as a video camera scanner etc LGE recommends connecting high power USB devices directly to the computer
13. jury a Do not place the monitor on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer Do not try to roll a stand with small casters across thresholds or deep pile carpets To Prevent Fire or Hazards a Always turn the monitor OFF if you leave the room for more than a short period of time Never leave the monitor ON when leaving the house a Keep children from dropping or pushing objects into the monitor s cabinet openings Some internal parts carry hazardous voltages a Do not add accessories that have not been designed for this monitor a During a lightning storm or when the monitor is to be left unattended for an extended period of time unplug it from the wall outlet a Do not bring magnetic devices such as magnets or motors near the picture tube Q Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the monitor where the power cord is subject to damage Do not use this monitor near water such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Monitors are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER a Block the bottom ventilation slots by placing the monitor on a bed sofa rug etc
14. ly on the screen I see waves on the screen e This occurs in inverse proportion to the screen focus which can be caused by a particular frequency or video card Brighten the screen and use the MOIRE icon on the screen adjustment menu to adjust the screen Have you installed the monitor driver Have you installed the monitor driver Be sure to install the monitor driver from the monitor driver CD or diskette that comes with your monitor Or you can also download the driver from our web site httovAwww ige com Specifications Picture Tube Sync Input Video Input Plug amp Play Power Consumption Dimensions amp Weight with tilt swivel stand Power Input Environmental Conditions Tilt Swivel Stand Signal cable Power cord Regulations NOTE 22 inches 20 inches viewable Natural Flat Tube 90 degree deflection 0 24mm Grille pitch ARAS Anti Reflective Anti Static coating Horizontal Freq 30 124kHz Automatic Vertical Freq 50 160Hz Automatic Input Form Separate TTL Positive Negative CompositeTTL Positive Negative SOG Sync On Green Signal Input 15 pin D Sub 5 BNC Connector Input Form Separate RGB Analog 0 7Vp p 75 ohm Positive Resolution max 2048 x 1536 75Hz DDC 1 2B Normal lt 115W 130W Stand by Suspend lt 8W 20W Power Off lt 3wiisW with USB Width 50
15. n OSD Adjust Description SHAPE H Linearity nit 2 To adjust the horizontal width of edge of E lt n the image dimm ein bod S v Linearity To adjust the vertical width of edge of the image od Recall You can use this function to reload the modified parameters for screen display operation as specified by the user after purchase Zoom H V Linearity These This function is available for recalled options may differ depending on the designated models only mode selected Preset User or New To customize the color of the screen OSD Adjust Description COLOR PRESET 6500K 9300K Select the screen color PRESET 0200K ok e 6500K Slightly reddish white TEMP cermin e 9300K Slightly bluish white RED GREEN TEMP Select the screen temperature which you BLUE to L prefer among reddish or bluish or any color in between RED GREEN Set your own color levels BLUE On Screen Display OSD Selection and Adjustment To customize the screen status for a user s operating environment OSD Adjust Description SETUP N LANGUAGE gt ENGLISH VIDEO LEVEL gt 0 7V WEN ae OSD TIME gt 10SEC SETUP VIDEO LEVEL gt 0 7V LANGUAGE ENGLISH OSD POSITION m RESET gt ON CLAMP SEP This function is available for designated models only EOE VIDEO LEVEL This item is used to select the monitor s LANGUAGE OSD TIME input signal lev
16. roperly power outlet that is easily accessible and close to the monitor NOTE This is a simplified representation of the rear view a This rear view represents a general model your monitor may differ from the view as Vom Power Cord Cord Wall outlet type Varies according to model PC outlet type i p gt Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector Control Panel Functions Front Panel Controls pe POIT o i G 6 AUTO MENU i A SELECT INPUT o Q Q i J Doi P Q D SUB vV 3 4 0 Control Function Power Button Use this button to turn the monitor on or off Power DPMS This Indicator lights up green when the monitor Indicator operates normally If the monitor is in DPM Energy Saving mode this indicator color changes to amber Button display A V 4 gt Buttons Use these buttons to choose or adjust items in the on screen display SELECT or SET Use this button to enter a selection in the on Button screen display MENU or OSD Use this button to enter or exit the on screen Control Panel Functions Control SHARPNESS M Direct Access Function O B Button Bring up Contrast adjustment Button Bring up Brightness
17. sage appears when the signal from the PC FREQUENCY message video card is out of horizontal or vertical frequency onthe screen range of the monitor See the Specifications section of this manual and configure your monitor again Do you see a SELF This message appears when the signal cable between DIAGNOSITICS message your PC and your monitor is not connected Check the on the screen signal cable and try again In case of using the BNC connector this message also appears in the DPM mode Check the signal cable or press any key on the keyboard to bring up the screen The screen is flickering ls the vertical frequency Set the vertical frequency to 72Hz or higher and less than 70Hz or is your consult the video card user manual for instructions on monitor set to the converting to a non interlaced mode interlaced mode You can set this option under the Display icon of the Control Panel Do you have any Remove magnetic sources such as power magnetic material such adapters speakers or high voltage lines away from as adapter or high the monitor voltage line near to your monitor Do you hear a ding e Use the normal degaussing function This function sound while the monitor Clears the screen and reduces any screen blur that may occur due to the surrounding magnetic field The screen may flicker for about 5 seconds accompanied by a ding sound is flickering
Download Pdf Manuals
Related Search