Home

Cisco WSX5111 Network Adapter

1. exp 2 x 1 fora module inserted Syntax Integer 0 65535 Access Read only chassisModel chassisGrp 16 Indicates the manufacturer s model number for the chassis Syntax DisplayString SIZE 0 8 Access Read only 2 18 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Chassis Group chassisSerialNumber chassisGrp 17 Indicates the serial number of the chassis Syntax Integer 0 999999999 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 19 Module Group Module Group The Module group provides module descriptions such as the module type firmware version hardware version serial number operational status and self test results Implementation of the Module group is mandatory for all Cisco Workgroup Stack products moduleTable moduleGrp 1 Contains a list of module entries The number of entries is given by the value of chassisNumSlots and includes the following variables moduleIndex moduleType moduleSerialNumber moduleHwHiVersion moduleHwLoVersion moduleFwHiVersion moduleFwLoVersion moduleSwHiVersion moduleSwLoVersion moduleStatus moduleTestResult moduleAction moduleName moduleNumPorts modulePortStatus moduleSubType moduleModel moduleHwVersion moduleFwVersion moduleSwVersion and moduleStandbyStatus moduleIPaddress moduleIPvlan Syntax SEQUENCE OF ModuleEntry Access Not accessible moduleEntry moduleTable 1 Provides information about one
2. Catalyst 3000 series Multimode fiber Fast Ethernet Multimode fiber OC 3 ATM Single mode fiber OC 3 ATM UTP OC 3 ATM Single mode fiber Fast Ethernet 10 100 UTP Ethernet Catalyst 3000 series 5000 series MII Ethernet VLAN router module for the Catalyst 5000 series Indicates the current operational status of the port Syntax Integer other 1 None of the following ok 2 Status satisfactory Catalyst 5000 Series Switch Workgroup MIBs 2 31 Port Group portOperStatus portEntry 6 Continued minorFault 3 Minor problem majorFault 4 Major problem Access Read only portCrossGroupIndex portEntry 7 Indicates a cross reference to another MIB group for this port The value is dependent on the type of port For an FDDI port the value corresponds to the snmpFddiPORTSMTIndex Syntax Integer 1 16 Access Read only portAdditionalStatus portEntry 8 Provides additional status information for the port The value is a sum It initially takes the value zero then for each state that is true two raises to a power and is added to the sum The following table lists the powers State Power Transmit 0 Receive 1 Collision 2 2 32 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Port Group portAdditionalStatus portEntry 8 Continued Transmit state indicates that at least one packet was transmitted by the port in the last polling period Receive state indicates that at least one pa
3. VLAN Group VLAN Group The VLAN group manages and controls variables that implement VLAN functions such as port location port VLAN information list of port entries priority level used to access the switching media and operational status Implementation of the VLAN group is mandatory for all Cisco Workgroup Stack products that implement VLAN functions Note vlanGrp is not used vianTable vlanGrp 2 Contains a list of VLAN entries The number of entries is determined by the number of VLANs supported by the system The following variables are available vlanIndex and vlanSpantreeEnable Syntax SEQUENCE OF VlanEntry Access Not accessible vianEntry vlanTable 1 Contains information for a particular VLAN Syntax VlanEntry Access Not accessible vianIndex vlanEntry 1 Indicates an index value that uniquely identifies the VLAN associated with this information Syntax Integer 0 1023 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 39 VLAN Group vianSpantreeEnable vlanEntry 2 Enables or disables Spanning Tree Protocol for this VLAN Syntax Integer enabled 1 Spanning Tree Protocol is enabled default disabled 2 Spanning Tree Protocol is disabled Access Read write End of Table vianPortTable vlanGrp 3 Contains a list of VLAN port entries The number of entries is determined by the number of modules in the chassis and the number of ports on each module The follo
4. default Access Read write ntpBcastDelay ntpGrp 2 Estimates the round trip time in microseconds for NTP broadcasts The range is from 1 to 999999 Syntax Integer 1 999999 Access Read write Access 3000 3000 2 60 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Network Time Protocol Group ntpClient ntpGrp 3 Enables or disables the NTP feature Syntax Integer enabled 1 Catalyst 5000 acts as an NTP client disabled 2 Catalyst 5000 does not act as an NTP client default Access Read write ntpServerTable ntpGrp 4 Contains a list of NTP server entries This table lists a maximum of ten entries and contains the following variables ntpServerAddress and ntpServerType Syntax SEQUENCE OF NtpServerEntry Access Not accessible ntpServerEntry ntpServerTable 1 Contains NTP information for a particular entry Syntax NtpServerEntry Access Not accessible ntpServerAddress ntpServerEntry 1 Contains NTP Server s IP address Syntax IpAddress Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 61 Network Time Protocol Group ntpServerType ntpServerEntry 2 Adds or removes entries to the ntpServerTable To add a new entry to the ntpServerTable set this object to valid 1 for an IP address that is not in the table To remove an entry from the table set this object to invalid 2 Syntax Integer valid 1 Add this entry invalid 2 Remove this e
5. earl 5 fddi 6 ip 7 pruning 8 snmp 9 spantree 10 system 11 2 58 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference System Log Information Group syslogMessageFacility syslogMessageControlEntry 1 Continued Access tac 12 tcp 13 telnet 14 tftp 15 vtp 16 vmps 17 Read only syslogMessageSeverity syslogMessageControlEntry 2 Indicates the system log message severity Syntax Access Integer emergencies 1 alerts 2 critical 3 errors 4 warnings 5 notification 6 informational 7 debugging 8 Read write Table End of Catalyst 5000 Series Switch Workgroup MIBs 2 59 Network Time Protocol Group Network Time Protocol Group The Network Time Protocol NTP group controls and manages variables that pertain to NTP functions such as indicate whether the Catalyst 5000 series switch should act as a broadcast or NTP client or not set NTP broadcast round trip time in microseconds list NTP IP address set the system to change for daylight saving time and set time zone Implementation of the NTP group is optional but within the group all the elements are mandatory If the NTP feature is implemented the entire group should be implemented ntpBcastClient ntpGrp 1 Enables or disables the broadcast client feature Syntax Integer enabled 1 Catalyst 5000 acts as a broadcast client disabled 2 Catalyst 5000 does not act as a broadcast client
6. Syntax TimeTicks Access Read write Note systemGrp 14 is not used sysEnableModem systemGrp 15 Enables or disables the RS 232 port modem control lines Syntax Integer enabled 1 RS 232 port modem control lines are enabled disabled 2 RS 232 port modem control lines are disabled default Access Read write 2 6 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference System Group sysEnableRedirects systemGrp 16 Specifies whether the system can send or receive Internet Control Message Protocol ICMP redirect messages Syntax Integer enabled 1 The system can send or receive ICMP redirect messages disabled 2 The system cannot send or receive ICMP redirect messages Access Read write sysEnableRmon systemGrp 17 Specifies whether the SNMP agent supports the Remote Monitoring RMON MIB Syntax Integer enabled 1 The SNMP agent supports the RMON MIB default disabled 2 The SNMP agent does not support the RMON MIB Access Read write sysArpAgingTime systemGrp 18 Indicates the aging time of the ARP table Syntax Integer 0 1000000 default is 1200 Access Read write sysTrafficPeak systemGrp 19 Indicates the peak traffic meter value since the last time port counters were cleared or the system started see sysClearPortTime Syntax Integer 0 100 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 7 System Group sysTrafficPeakTime systemGr
7. cvbStpForwardingMap cvbStpEntry 2 An indication of which ports are forwarding by spanning tree for the specified VLAN The octet string contains one bit per port on the bridge for the specified VLAN Each bit within the octet string represents one port of the device The ordering of ports represented within the octet string is in the same order as in the RFC 1493 dot1dStpPortTable 2 74 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Spanning Tree Status Group The bit value interpretation related to RFC 1493 dotldStpPortState values is as follows 1 forwarding 0 disabled blocking listening learning broken or nonexistent Syntax OCTET STRING SIZE 0 128 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 75 Spanning Tree Status Group 2 76 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference
8. following snmpV 1 2 SNMP smux 3 SNMP MUX subagent snmpV2V1 4 Bilingual SNMP Version 2 and 1 Access Read only 2 2 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference System Group sysIpAddr systemGrp 2 Specifies the IP address Syntax IpAddress Access Read write sysNetMask systemGrp 3 Specifies the subnet mask Syntax IpAddress Access Read write sysBroadcast systemGrp 4 Specifies the broadcast address Syntax IpAddress Access Read write sysTrapReceiverTable systemGrp 5 Contains a list of Network Management Station addresses that should receive trap messages from this system when an exception condition occurs and includes the following variables sysTrapReceiverType sysTrapReceiverAddr and sysTrapReceiverComm Syntax SEQUENCE OF SysTrapReceiverEntry Access Not accessible sysTrapReceiverEntry sysTrapReceiverTable 1 Provides a trap receiver table entry Syntax SysTrapReceiverEntry Access Not accessible Catalyst 5000 Series Switch Workgroup MIBs 2 3 System Group sysTrapReceiverType sysTrapReceiverEntry 1 Adds or deletes an entry from the sysTrapReceiverTable Syntax Integer valid 1 Add this entry invalid 2 Remove this entry Access Read write sysTrapReceiverAddr sysTrapReceiverEntry 2 Specifies the IP address for the trap receiver Syntax IpAddress Access Read only sysTrapReceiverComm sysTrapReceiverEntry 3 Provides a community strin
9. has been assigned a VLAN that is not currently active active 2 The currently assigned VLAN is active shutdown 3 The port has been shut down as a result of a VMPS response on a dynamic port End of Table 2 44 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference VLAN Group vmps Table vlanGrp 4 Contains a list of VMPS IP addresses maximum three addresses The following variables are available vmpsAddr vmpsType Syntax SEQUENCE OF VmpsEntry Access Not accessible vmpsEntry vmpsTable 1 Contains a list of VMPS entries Syntax VmpsEntry Access Not accessible vmpsAddr vmpsEntry 1 The VMPS IP address To configure the internal VMPS use the same IP address as specified in sysIpAddr Syntax IpAddress Access Read only vmpsType vmpsEntry 2 To remove an entry from the table set this object to invalid 1 To add a new entry to the vmpsTable set this object to primary 2 or other 3 for an IP address which is not already in the table The primary entry will be used first if it is reachable Otherwise one of the other entries will be used Setting one entry to primary 2 causes any previous primary entry to change to other 3 Catalyst 5000 Series Switch Workgroup MIBs 2 45 VLAN Group vmpsType vmpsEntry 2 Continued Syntax Integer invalid 1 Remove this entry primary 2 The primary entry other 3 A lower priority entry Access Read write End of Table vmps
10. invalid 2 Syntax Integer valid 1 Add this entry invalid 2 Remove this entry Access Read write End of Table syslogConsoleEnable syslogGrp 2 Indicates whether the system log messages should be sent to console Syntax Integer enabled 1 System log messages are sent to console disabled 2 System log messages are not sent to console default Access Read write syslogHostEnable syslogGrp 3 Indicates whether the system log messages should be sent to syslog servers Syntax Integer enabled 1 System log messages are sent to syslog servers disabled 2 System log messages are not sent to syslog servers default Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 57 System Log Information Group syslogMessageControlTable syslogGrp 4 This table contains the information about what system log messages should be sent to syslog host console login session and or logged into the internal buffer and includes the following variables syslogMessageFacility and syslogMessageSeverity Syntax Access SEQUENCE OF SyslogMessageControlEntry Not accessible syslogMessageControlEntry syslogMessageControlTable 1 Provides a system log message control table entry Syntax Access SyslogMessageControlEntry Not accessible syslogMessageFacility syslogMessageControlEntry 1 Provides the system log message facility Syntax Integer cdp 1 cgmp 2 disl 3 dvlan 4
11. match the sysCommunityRw string the message is then compared with the sysCommunityRo string If it matches read only access is granted to all items in the MIB except for restricted items such as community strings Restricted items appear empty when read If it does not match access is denied no response is sent back to the SNMP requestor and an SNMP trap is sent to the SNMP trap receivers if configured Note This item is only accessible when using the community string defined in sysCommunityRwa Syntax DisplayString SIZE 0 20 Access Read write sysEnableChassisTraps systemGrp 24 Specifies whether the chassisAlarmOn and chassisAlarmOff traps in this MIB should be generated Syntax Integer enabled 1 chassisAlarmOn and chassisAlarmOff traps in this MIB are generated disabled 2 chassisAlarmOn and chassisAlarmOff traps in this MIB are not generated default Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 9 System Group sysEnableModuleTraps systemGrp 25 Specifies whether the moduleUp and moduleDown traps in this MIB should be generated Syntax Integer enabled 1 moduleUp and moduleDown traps in this MIB are generated disabled 2 moduleUp and moduleDown traps in this MIB are not generated default Access Read write sysEnableBridgeTraps systemGrp 26 Specifies whether the newRoot and topologyChange traps in the BRIDGE MIB RFC 1495 should be generated Sy
12. of the TACACS group is optional but within the group all the elements are mandatory If the TACACS feature is implemented the entire group must be implemented tacacsLoginAuthentication tacacsGrp 1 Indicates whether the login authentication using the TACACS feature is enabled or disabled Syntax Integer enabled 1 Login authentication using the TACACS feature is enabled disabled 2 Login authentication is not using the TACACS feature default Access Read write tacacsEnableAuthentication tacacsGrp 2 Indicates whether the enable authentication using the TACACS feature is enabled or disabled Syntax Integer enabled 1 Authentication using the TACACS feature is enabled disabled 2 Authentication using the TACACS feature is disabled default Access Read write 2 64 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Terminal Access Controller Access Control System Group tacacsLocalLoginAuthentication tacacsGrp 3 Indicates whether the login authentication using local password is enabled or disabled Syntax Integer enabled 1 Login authentication using local password is enabled default disabled 2 Login authentication using local password is disabled Access Read write tacacsLocalEnableAuthentication tacacsGrp 4 Indicates whether the enable authentication using local password is enabled or disabled Syntax Integer enabled 1 Authentication using local password is enab
13. variables portChannelModuleIndex portChannelPortIndex portChannelPorts portChannelAdminStatus portChannelOperStatus Syntax SEQUENCE OF PortChannelEntry Access Not accessible portChannelEntry portChannelTable 1 Provides an entry containing information for a particular port on a module Syntax PortChannelEntry Access Not accessible portChannelModuleIndex portChannelEntry 1 Indicates an index value that uniquely identifies the module where this port is located The value is determined by the chassis slot number in which the module is located Syntax Integer 1 16 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 71 Port Channel Group portChannelPortIndex portChannelEntry 2 Indicates an index value that uniquely identifies this port within a module Syntax Integer 1 255 Access Read only portChannelPorts portChannelEntry 3 Indicates the set of ports on a module which are channeled together Each octet within the value of this object specifies a set of eight ports with the first octet specifying ports 1 through 8 the second octet specifying ports 9 through 16 and so forth Within each octet the most significant bit represents the lowest numbered port and the least significant bit represents the highest numbered port Therefore each port is represented by a single bit within the value of this object If given a value of 1 the port is included in the set of channel ports The defa
14. Access Read only None of the following No power supply 50 watt supply 200 watt supply 600 watt supply 80 watt supply 130 watt supply 350 watt supply 350 watt supply 175 watt supply 350 watt supply DC 1100 watt supply 1100 watt supply DC 1200 watt supply 155 watt supply 155 watt supply w PFC 155 watt supply DC Catalyst 5000 Series Switch Workgroup MIBs 2 15 Chassis Group chassisPs2Status chassisGrp 7 Provides the status of power supply number 2 If the status is not ok the value of chassisPs2TestResult gives more detailed information about the power supply s failure condition s Syntax Integer other 1 None of the following ok 2 Status satisfactory minorFault 3 Minor problem majorFault 4 Major problem Access Read only chassisPs2TestResult chassisGrp 8 Provides the test result for power supply number 2 A zero indicates that the supply passed all tests Bits set in the result indicate error conditions Syntax Integer 0 65535 Access Read only chassisFanStatus chassisGrp 9 Provides the status of the chassis fan If the status is not ok the value of chassisFanTestResult gives more detailed information about the fan s failure condition s Syntax Integer other 1 None of the following ok 2 Status satisfactory minorFault 3 Minor problem majorFault 4 Major problem Access Read only 2 16 Catalyst 5000 Series Switch Workgroup MIB User Quic
15. Action vlanGrp 5 When read this object returns the result of the last action requested other 1 inProgress 2 success 3 noResponse 4 noPrimary Vmps 5 noDynamicPort 6 or noHostConnected 7 Setting this object to reconfirm 8 causes the switch to contact the VMPS immediately to reconfirm the current VLAN assignments for all dynamic ports on the switch Normally VLAN assignments for dynamic ports are reconfirmed once an hour Syntax Integer other 1 None of following read only inProgress 2 Read only success 3 Read only noResponse 4 Read only noPrimaryVmps 5 No VMPS configured read only noDynamicPort 6 No dynamic ports configured read only noHostConnected 7 No hosts on dynamic ports read only reconfirm 8 Write only Access Read write 2 46 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference VLAN Group vmpsAccessed vlanGrp 6 The IP address of the last VMPS accessed If there was no response from the last VMPS request the value returned is 0 Syntax IpAddress Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 47 Security Group Security Group The Security group controls and manages variables that pertain to port security functions such as listing security information for a specific port port security entries module index port index and enabling source MAC address monitoring Implementation of the Security group is optional but within t
16. Bs 2 11 Chassis Group Chassis Group The Chassis group manages and controls the various functions of the chassis components such as the power supply type and status number of slots available for plug in modules and chassis model number Implementation of the Chassis group is mandatory for all Cisco Workgroup Stack products chassisSysType chassisGrp 1 Indicates the chassis system type Syntax Integer other 1 None of the following wsc 1000 3 2 8 port CDDI concentrator wsc 1001 4 2 8 port CDDI concentrator wsc1100 5 2 16 port FDDI CDDI concentrator wsc5000 6 5 slot switch wsc2900 7 Closed 2 slot switch wsc5500 8 13 slot switch wsc5002 9 2 slot switch wsc1200 11 2 8 port FDDI Ethernet switch wsc1400 12 2 slot FDDI CDDI concentrator Access Read only 2 12 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Chassis Group chassisBkpIType chassisGrp 2 Indicates the chassis backplane type Syntax Access Integer other 1 None of the following fddi 2 fddi fddiEthernet 3 fddi and ethernet giga 4 gigabit packet switch giga3 5 3 6 gigabit switch giga3E 6 3 6 gigabit switch enhanced Read only chassisPs1Type chassisGrp 3 Indicates the type of power supply number 1 Syntax Integer other 1 None of the following none 2 No power supply w50 3 50 watt supply w200 4 200 watt supply w600 5 600 watt supply w80 6 80 watt supply w130 7 130 w
17. CHAPTER 2 Catalyst 5000 Series Switch Workgroup MIBs This chapter contains descriptions of the groups and variables used within the Cisco Workgroup MIB file the CISCO STACK MIB For information regarding other MIBs supported by the Catalyst 5000 series switch refer to the Cisco Management Information Base MIB User Quick Reference publication Note Default values are included where available This chapter includes the following sections System Group Chassis Group Module Group Port Group Trivial File Transfer Protocol Group Monitor Group VLAN Group Security Group Multicast Group Domain Naming System Group System Log Information Group Catalyst 5000 Series Switch Workgroup MIBs 2 1 System Group Network Time Protocol Group Terminal Access Controller Access Control System Group IP Permit List Group Port Channel Group Spanning Tree Status Group Note In this document reference to the Catalyst 5000 series switches refers specifically to the Catalyst 5000 Catalyst 5002 and Catalyst 5500 switches System Group The System group manages and controls system wide functionality of the Catalyst 5000 series switch products Implementation of the System group is mandatory for all Cisco Workgroup Stack products sysMgmtType systemGrp 1 Specifies the type of network management running on this system Syntax Integer other 1 None of the
18. M RJ 45 connector 12 port 100BaseFX multimode SC connector 12 port 10 100BaseTX RJ 45 connector 48 port 4 segment 10BaseT telco connector Catalyst 5000 Series Switch Workgroup MIBs 2 21 Module Group moduleType moduleEntry 2 Continued moduleSerialNumber moduleEntry 3 wsx5006 38 wsx5005 39 wsx5509 40 wsx5506 41 wsx5505 42 wsx5156 43 wsx5157 44 wsx5158 45 wsx5114 47 wsx5223 48 wsx5224 49 wsx5012 50 wsx5302 52 wsx5213a 53 wsx5201 55 wsx5203 56 Access Read only Supervisor module 100BaseFX multimode SC connector Supervisor module 100BaseFX single mode SC connector Supervisor module II 100BaseTX RJ 45 MID Supervisor module II 100BaseFX multimode SC Supervisor module II 100BaseFX single mode SC 2 port UTP OC 3 ATM RJ 45 connector 2 port single mode OC 3 ATM SC connector 2 port multimode OC 3 ATM SC connector 6 port single mode 6 port MM 100BaseFX SC connector 24 port 3 segment 100BaseTX RJ 45 connector 24 port 10 100BaseTX RJ 45 connector 48 port 10BaseT telco connector VLAN router module for the Catalyst 5000 12 port 10 100BaseTX RJ 45 connector 12 port 100BaseFX multimode SC connector 12 port 10 100BaseTX RJ 45 connector Provides the serial number of the module Integer 0 999999999 Access Read only 2 22 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Module Group moduleHwHivVersion moduleEn
19. String SIZE 0 255 Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 55 System Log Information Group System Log Information Group The System Log group controls and manages variables that pertain to System Log functions such as list system log servers provide system log IP address add or remove a system log server and indicate where system log messages are to be sent console or system log server Implementation of the syslog group is optional but within the group all the elements are mandatory If the syslog feature is implemented the entire group must be implemented syslogServerTable syslogGrp 1 Contains a list of system log servers maximum of three and includes the following variables syslogServerAddr and syslogServerType Syntax SEQUENCE OF SyslogServerEntry Access Not accessible syslogServerEntry syslogServerTable 1 Provides a system log server table entry Syntax SyslogServerEntry Access Not accessible syslogServerAddr syslogServerEntry 1 Provides the IP address of a system log server Syntax IpAddress Access Read only 2 56 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference System Log Information Group syslogServerType syslogServerEntry 2 Adds or removes syslogServerTable entries To add a new entry into syslogServerTable set this object to valid 1 for an IP address not already in the table To remove an entry from the syslogServerTable set to
20. acturer s model number for the module Syntax DisplayString SIZE 0 8 Access Read only moduleHwVersion moduleEntry 18 Indicates the hardware version of the module Syntax DisplayString SIZE 0 12 Access Read only moduleFw Version moduleEntry 19 Indicates the firmware version of the module Syntax DisplayString SIZE 0 12 Access Read only moduleSwVersion moduleEntry 20 Indicates the software version of the module Syntax DisplayString SIZE 0 20 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 27 Module Group moduleStandbyStatus moduleEntry 21 Provides the status of a redundant module Syntax Integer other 1 None of the following active 2 The redundant module is active standby 3 The redundant module is in standby mode error 4 The redundant module is in error Access Read only moduleIPaddress moduleEntry 22 Provides the IP address of the VLAN router module for the Catalyst 5000 If the module has a separate receive IP address it is reported here otherwise the value is OOOOO00H Syntax DisplayString Access Read only moduleIPvlan moduleEntry 23 Provides the VLAN IP address of the VLAN router module for the Catalyst 5000 If the moduleIpAddress is valid this object reports to the VLAN that this IP address is accessible otherwise the value is 0 Syntax DisplayString Access Read only End of Table 2 28 Catalyst 5000 Seri
21. att supply wsc5008 8 350 watt supply wsc5008a 9 350 watt supply w175 10 175 watt supply wsc5068 11 350 watt supply DC Catalyst 5000 Series Switch Workgroup MIBs 2 13 Chassis Group chassisPs1Type chassisGrp 3 Continued wsc5508 12 1100 watt supply wsc5568 13 1100 watt supply DC wsc5508a 14 1200 watt supply w155 15 155 watt supply wl55pfe 16 155 watt supply w PFC w155dc 17 155 watt supply DC Access Read only chassisPs1Status chassisGrp 4 Provides the status of power supply number 1 If the status is not ok the value of chassisPs1TestResult gives more detailed information about the power supply s failure condition s Syntax Integer other 1 None of the following ok 2 Status ok minorFault 3 Minor problem majorFault 4 Major problem Access Read only chassisPs1TestResult chassisGrp 5 Provides the test result for power supply number 1 A zero indicates that the supply passed all tests Bits set in the result indicate error conditions Syntax Integer 0 65535 Access Read only 2 14 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Chassis Group chassisPs2Type chassisGrp 6 Indicates the type of power supply number 2 Syntax Integer other 1 none 2 w50 3 w200 4 w600 5 w80 6 w130 7 wsc5008 8 wsc5008a 9 w175 10 wsc5068 11 wsc5508 12 wsc5568 13 wsc5508a 14 w155 15 w155pfc 16 w155dc 17
22. cally or dynamically Syntax Integer routerPresent 1 The router presence is configured statically as present dynamic 3 The router presence is learned dynamically default Access Read write mcastRouterOperStatus mcastRouterEntry 4 Indicates whether an IP multicast router is present on this port Syntax Integer routerPresent 1 An IP multicast router is present noRouter 2 An IP multicast router is not present Access Read only End of Table 2 52 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Multicast Group mcastEnableCgmp multicastGrp 2 Enables or disables Cisco Group Management Protocol CGMP on the device When CGMP is enabled in conjunction with Cisco routers running CGMP only the required ports will participate in IP multicast groups Syntax Integer enabled 1 Cisco Group Management Protocol is enabled disabled 2 Cisco Group Management Protocol is disabled default Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 53 Domain Naming System Group Domain Naming System Group The Domain group controls and manages variables that pertain to domain functions such as enables or disables the Domain Naming System DNS feature adds or removes servers and specifies the domain name Implementation of the DNS group is optional but within the group all the elements are mandatory If DNS features are implemented the entire group must be implemented dn
23. ceives a request to become a trunk Access Read write 2 42 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference VLAN Group vianPortIslOperStatus vlanPortEntry 8 Indicates if the port is actually trunking or not In the case of ISL capable ports the status depends on the success or failure of the negotiation process initiated by the port to become a trunk or nontrunk In the case of 802 10 capable ports it is directly related to the on off administrative status Syntax Integer trunking 1 The port is trunking notTrunking 2 The port is not trunking Access Read only vianPortIsIPriority Vians vlanPortEntry 9 Specifies an indication of which VLANs have a better dotldStpPortPriority value This object can be used to perform load balancing on ISLs via Spanning Tree An ISL has two dotidStpPortPriority values which are shared by all the VLANs on the link The VLANs indicated by this object have priority over the other VLANs on the link This is an octet string value with bits set to indicate priority VLANs It can be interpreted as a sum of f x as x goes from 0 to 1023 where f x 0 fora VLAN x which does not have priority and f x exp 2 x for a VLAN x which has priority Setting the dot dStpPortPriority value for any of the VLANs indicated by this object causes the dotldStpPortPriority value for all the VLANs indicated by this object to be set to the same value Setting the dotldStpPortPriority value f
24. cket was received by the port in the last polling period Collision state indicates that at least one collision was detected on the port in the last polling period Note Ifa state is not applicable to a particular port its value is always false for that port Syntax Integer 0 7 Access Read only portAdminSpeed portEntry 9 Specifies the desired speed of the port in bits per second The current operational speed of the port can be determined from ifSpeed Syntax Integer autoDetect 1 s10000000 10000000 s100000000 100000000 155000000 155000000 s400000000 400000000 for the VLAN router module for the Catalyst 5000 series Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 33 Port Group portDuplex portEntry 10 Specifies whether the port is operating in half duplex or full duplex mode Syntax Integer half 1 Operating in half duplex mode full 2 Operating in full duplex mode Access Read write portifIndex portEntry 11 Indicates the value of the instance of the ifIndex object defined in MIB II for the interface corresponding to this port Syntax Integer 1 4294967295 Access Read only portSpantreeFastStart portEntry 12 Enables or disables spanning tree fast start mode A port with fast start enabled is immediately put in spanning tree forwarding state on link up rather than starting in blocking state which is the normal operation Fast start enabled is use
25. es Switch Workgroup MIB User Quick Reference Port Group Port Group The Port group provides information for a particular port on a module such as port location port name as designated by the network administrator port type operational status mode half or full duplex and port security Implementation of the Port group is mandatory for all Cisco Workgroup Stack products portTable portGrp 1 Contains a list of port entries The number of entries is determined by the number of modules in the chassis and the number of ports on each module and includes the following variables portModuleIndex portIndex portCrossIndex portName portType portOperStatus portCrossGroupIndex portAdditionalStatus portAdminSpeed portDuplex portIfIndex and portSpantreeFastStart Syntax SEQUENCE OF PortEntry Access Not accessible portEntry portTable 1 Contains information for a particular port on a module Syntax PortEntry Access Not accessible portModuleIndex portEntry 1 Indicates an index value that uniquely identifies the module where this port is located The chassis slot number which the module is plugged into determines the value Valid entries are to the value of chassisNumSlots Syntax Integer 1 16 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 29 Port Group portIndex portEntry 2 Indicates an index value that uniquely identifies this port within a module The location of the p
26. ful when the port is known to be connected to a single station that has problems waiting for the normal spanning tree operation to put the port in forwarding state Syntax Integer enabled 1 Operating in spanning tree fast start mode disabled 2 Not operating in spanning tree fast start mode default Access Read write End of Table 2 34 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Trivial File Transfer Protocol Group Trivial File Transfer Protocol Group The Trivial File Transfer Protocol TFTP group manages and controls products that implement TFTP upload download functions such as source destination host for the transfer TFTP transfer filename code configuration transfer software or firmware transfer and TFTP action results Implementation of the TFTP group is mandatory for all Cisco Workgroup Stack products that implement TFTP upload download functions tftpHost tftpGrp 1 Indicates the name of the source destination host for the TFTP transfer Syntax DisplayString SIZE 0 64 Access Read write tftpFile tftpGrp 2 Indicates the name of the file for TFTP transfer Syntax DisplayString SIZE 0 64 Access Read write tftpModule tftpGrp 3 Specifies which module s code configuration is being transferred Syntax Integer 0 16 Access Read write If set to 0 the system recognizes the image type the given file contains and downloads it to all modules of the appropriate type
27. g used for trap messages to this trap receiver Syntax DisplayString SIZE 0 20 Access Read write End of Table Note systemGrp 6 and systemGrp 7 are not used sysTraffic systemGrp 8 Specifies the traffic meter value for example the percentage of bandwidth utilization for the previous polling interval Syntax Integer 0 100 Access Read only 2 4 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference System Group sysReset systemGrp 9 Provides a method of resetting the control logic of all modules in the system Syntax Integer other 1 None of the following reset 2 Resetting Access Read write sysBaudRate systemGrp 10 Specifies the baud rate in bits per second bps of the RS 232 port Syntax Integer b600 600 600 bps b1200 1200 1200 bps b2400 2400 2400 bps b4800 4800 4800 bps b9600 9600 9600 bps default b19200 19200 19200 bps b38400 38400 38400 bps Access Read write Note systemGrp 11 is not used Catalyst 5000 Series Switch Workgroup MIBs 2 5 System Group sysClearMacTime systemGrp 12 Specifies the time in hundredths of a second since the Media Access Control MAC counters were last cleared Writing 0 causes the MAC counters to be cleared Syntax TimeTicks Access Read write sysClearPortTime systemGrp 13 Specifies the time in hundredths of a second since the port counters were last cleared Writing O clears the port counters
28. he group all the elements are mandatory If the Security feature is implemented the entire group must be implemented portSecurityTable securityGrp 1 Contains a list of port security entries The number of entries is determined by the number of ports in the system that support the Security feature and includes the following variables portSecurityModuleIndex portSecurityPortIndex portSecurityAdminStatus portSecurityOperStatus portSecurityLastSrcAddr and portSecuritySecureSrcAddr Syntax SEQUENCE OF PortSecurityEntry Access Not accessible portSecurityEntry portSecurityTable 1 Contains security information for a particular port Syntax PortSecurityEntry Access Not accessible portSecurityModuleIndex portSecurityEntry 1 Provides an index value that uniquely identifies the module where this port is located see portModuleIndex Syntax Integer 1 16 Access Read only 2 48 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Security Group portSecurityPortIndex portSecurityEntry 2 Provides an index value that uniquely identifies this port within a module see portIndex Syntax Integer 1 255 Access Read only portSecurity AdminStatus portSecurityEntry 3 Monitors source MAC addresses for all packets received on the port when security is enabled If an address is detected that does not match the portSecuritySecureSrcAddr the port is shut down and a linkDown trap is sent Syntax I
29. in the chassis Catalyst 5000 Series Switch Workgroup MIBs 2 35 Trivial File Transfer Protocol Group tftpAction tftpGrp 4 Setting this object to one of the acceptable values initiates the requested action using the information given in tftpHost tftpFile and tftpModule Setting this object to any other value results in an error Syntax Integer downloadConfig 2 Receive configuration from host file uploadConfig 3 Send configuration to the host file downloadSw 4 Receive software image from the host file uploadSw 5 Send software image to the host file downloadFw 6 Receive firmware image from the host file uploadFw 7 Send firmware image to the host file Access Read write tftpResult tftpGrp 5 Contains the result of the last TFTP action request Syntax Integer inProgress 1 success 2 noResponse 3 tooManyRetries 4 noBuffers 5 noProcesses 6 badChecksum 7 badLength 8 2 36 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Monitor Group tftpResult tftpGrp 5 Continued badFlash 9 serverError 10 userCanceled 11 wrongCode 12 Access Read only Monitor Group The Monitor group manages and controls variables that implement port monitoring functions such as monitoring port location monitoring destination port location packet type to be monitored and enabling port monitoring Implementation of the Monitor group is mandatory for all Cisco Workgroup Stack
30. k Reference Chassis Group chassisFanTestResult chassisGrp 10 Provides the test result for the chassis fan A zero indicates that the fan passed all tests Bits set in the result indicate error conditions Syntax Integer 0 65535 Access Read only chassisMinorAlarm chassisGrp 11 Provides the chassis minor alarm status Syntax Integer off 1 No chassis minor alarm has been detected on 2 A chassis minor alarm has been detected Access Read only chassisMajorAlarm chassisGrp 12 Provides the chassis major alarm status Syntax Integer off 1 No chassis major alarm has been detected on 2 A chassis major alarm has been detected Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 17 Chassis Group chassisTempAlarm chassisGrp 13 Provides the chassis temperature alarm status Syntax Integer off 1 Temperature within normal range on 2 Temperature too high critical 3 Critical temperature system shutdown imminent Access Read only chassisNumSlots chassisGrp 14 Indicates the number of slots in the chassis available for plug in modules Syntax Integer 1 16 Access Read only chassisSlotConfig chassisGrp 15 Indicates the slots in the chassis with modules inserted The syntax is an integer value with bits set to indicate configured modules It can be interpreted as a sum of f x as x goes from 1 to the number of slots where f x 0 for no module inserted and f x
31. led default disabled 2 Authentication using local password is disabled Access Read write tacacsNumLoginAttempts tacacsGrp 5 Indicates the number of login attempts allowed before the system locks you out Syntax Integer 1 10 default is 3 Access Read write tacacsDirectedRequest tacacsGrp 6 Indicates whether the directed request feature of TACACS is enabled or disabled Syntax Integer enabled 1 disabled 2 default Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 65 Terminal Access Controller Access Control System Group tacacsTimeout tacacsGrp 7 Indicates the duration in seconds to wait for a response from the TACACS server host Syntax Integer 1 255 default is 5 Access Read write Note tacacsAuthKey is only accessible when using the community string defined in sysCommunityRwa tacacsAuthKey tacacsGrp 8 Indicates the key used in encrypting the packets passed between the TACACS server and the client This key must match the one configured on the server Syntax DisplayString SIZE 0 100 default is Null Access Read write tacacsServerTable tacacsGrp 9 Contains a list of TACACS servers maximum of three and includes the following variables tacacsServerAddr and tacacsServerType Syntax SEQUENCE OF TacacsServerEntry Access Not accessible tacacsServerEntry tacacsServerTable 1 Provides a TACACS server table entry Syntax TacacsServerEn
32. module If the status is not ok the value of moduleTestResult gives more detailed information about the module s failure condition s Syntax Integer other 1 None of the following ok 2 Status satisfactory minorFault 3 Minor problem A minor problem is defined as a module that is under startup diagnostics not online or is disabled majorFault 4 Major problem A major problem is defined as a module not running for example no CPU or a major component diagnostic failure has occurred so that the module is not usable Access Read only 2 24 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Module Group moduleTestResult moduleEntry 11 Provides the results of the module s self test A zero indicates that the module passed all tests Bits set in the result indicate error conditions Syntax Integer 0 65535 Access Read only moduleAction moduleEntry 12 Specifies that this object when read returns one of the following results other 1 Module is permanently enabled enable 3 Module is currently enabled disable 4 Module is currently disabled Setting this object to one of the acceptable values gives the following results setting this object to any other value results in an error Syntax Integer other 1 Gives an error reset 2 Resets the module s control logic If configuring the VLAN router module for the Catalyst 5000 always set to reset 2 otherwise an er
33. module in a slot of the chassis Syntax ModuleEntry Access Not accessible moduleIndex moduleEntry 1 Indicates a unique value for each module within the chassis This value is determined by the chassis slot number where the module is inserted Valid entries are 1 to the value of chassisNumSlots Syntax Integer 1 16 Access Read only 2 20 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Module Group moduleType moduleEntry 2 Indicates the type of module wsx5013 24 wsx5011 25 wsx5010 26 wsx5113 27 wsx5101 28 wsx5103 29 wsx5104 30 wsx5105 31 wsx5155 32 wsx5154 33 wsx5 153 34 wsx5111 35 wsx5213 36 wsx5020 37 Syntax Integer other 1 None of the following empty 2 Nothing installed wsc 1000 3 2 8 port CDDI concentrator wsc1001 4 2 8 port FDDI C concentrator wsc 1100 5 2 16 port FDDI CDDI C concentrator wsc1200 11 2 8 port FDDI Ethernet switch wsc1400 12 2 slot FDDI CDDI C concentrator wsx5009 23 Supervisor module 100BaseTX RJ 45 MID 24 port 10BaseT RJ 45 connector 12 port 10BaseFL multimode ST connector 24 port 10BaseT telco connector 12 port 100BaseTX RJ 45 connector Dual attach multimode FDDI MIC connector Dual attach CDDI RJ 45 connector Dual attach single mode FDDI ST connector Dual attach multimode FDDI SC connector l port multimode OC 3 ATM SC connector l port single mode OC 3 ATM SC connector l port UTP OC 3 AT
34. ntax Integer enabled 1 newRoot and topologyChange traps in the BRIDGE MIB RFC 1495 are generated disabled 2 newRoot and topologyChange traps in the BRIDGE MIB RFC 1495 are not generated default Access Read write sysIpVlan systemGrp 27 Specifies this entity s IP address virtual LAN VLAN association Syntax Integer 0 1023 Access Read write 2 10 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference System Group sysConfigChangeTime systemGrp 28 Indicates the time in hundredths of a second since the configuration of the system was last changed Syntax TimeTicks Access Read only sysEnableRepeaterTraps systemGrp 29 Specifies whether the traps in the REPEATER MIB RFC 1516 should be generated Syntax Integer enabled 1 The traps in the REPEATER MIB RFC 1516 are to be generated disabled 2 The traps in the REPEATER MIB RFC 1516 are not to be generated default Access Read write sysBanner Motd systemGrp 30 Displays the message of the day banner on the command line interface before log in Syntax DisplayString SIZE 0 255 Access Read write sysEnableIpPermitTraps systemGrp 31 Indicates whether the IP permit traps in this MIB should be generated Syntax Integer enabled 1 The traps in this MIB are to be generated disabled 2 The traps in this MIB are not to be generated default Access Read write Catalyst 5000 Series Switch Workgroup MI
35. nteger enabled 1 Source MAC addresses are monitored for all packets received on the port disabled 2 Source MAC addresses are not monitored for all packets received on the port default Access Read write portSecurityOperStatus portSecurityEntry 4 Indicates whether the port has been shut down as a result of an insecure address being detected on a secure port Syntax Integer notShutdown 1 Port has not shut down shutdown 2 Port has been shut down as a result of an insecure address being detected on a secure port Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 49 Security Group portSecurityLastSrcAddr portSecurityEntry 5 Indicates the last source MAC address in a receive packet seen on the port Syntax OCTET STRING SIZE 6 Access Read only portSecuritySecureSrcAddr portSecurityEntry 6 Indicates the address to be compared with source MAC addresses of received packets when the portSecurityAdminStatus is enabled 1 Setting this value to 0 0 0 0 0 0 puts the port in learning mode so that the next source MAC address received by the port becomes the portSecuritySecureSrcAddr Syntax OCTET STRING SIZE 6 Access Read write End of Table 2 50 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Multicast Group Multicast Group The Multicast group controls and manages variables that pertain to multicast functions such as lists multicast router port ent
36. nteger enabled 1 disabled 2 default Access Read write ipPermitListTable ipPermitListGrp 2 Contains a list of a maximum of ten IP addresses with net masks of IP permit hosts If ipPermitEnable is enabled the system only accepts the inbound Telnet and SNMP access from the configured hosts in this table The following variables are included ipPermitAddress ipPermitMast ipPermitType Syntax SEQUENCE OF IpPermitListEntry Access Not accessible ipPermitListEntry IpPermitListTable 1 Provides an IP permit list table entry Syntax IpPermitListEntry Access Not accessible 2 68 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference IP Permit List Group ipPermitAddress ipPermitListEntry 1 Indicates the IP address of an IP permit host Syntax IP address Access Read only ipPermitMask ipPermitListEntry 2 Indicates the IP net mask of an IP permit host Syntax IP address Access Read only ipPermitType ipPermitListEntry 3 To add a new entry to the ipPermitListTable for an IP address and net mask which are not in the table set this object to valid 1 Setting to invalid 2 removes the corresponding entry from the ipPermitListTable Syntax Integer valid 1 Remove this entry invalid 2 Add this entry Access Read write End of Table ipPermitDeniedListTable ipPermitListGrp 3 Contains a list of the most recently denied addresses with the access type a maximum of ten IP addres
37. ntry Access Read write End of Table ntpSummertimeStatus ntpGrp 5 Sets the clock ahead or behind one hour respectively daylight saving time in USA This command becomes active only in the summer time Syntax Integer enabled 1 Sets the clock ahead 1 hour disabled 2 Sets the clock behind 1 hour default Access Read write ntpSummerTimezoneName ntpGrp 6 Provides summer time zone name for display purposes Syntax DisplayString SIZE 0 20 Access Read write 2 62 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Network Time Protocol Group ntpTimezoneName ntpGrp 7 Provides time zone name for display purposes Syntax DisplayString SIZE 0 20 Access Read write ntpTimezoneOffsetHour ntpGrp 8 Provides time offset in hours from Greenwich Mean Time Syntax Integer 12 12 Access Read write ntpTimezoneOffsetMinute ntpGrp 9 Provides time offset in minutes from Greenwich Mean Time Syntax Integer 0 59 Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 63 Terminal Access Controller Access Control System Group Terminal Access Controller Access Control System Group The Terminal Access Controller Access Control System TACACS group controls and manages variables that pertain to TACACS functions such as login parameter encryption of packets passed between the TACACS server and the client and IP address of a TACACS server Implementation
38. or any other VLAN causes the dot1dStpPortPriority value for all other VLANs to be set to the same value Syntax OCTET STRING SIZE 0 128 Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 43 VLAN Group vianPortAdminStatus vlanPortEntry 10 Indicates the method in which the port is assigned to a VLAN statically or dynamically When it is set to dynamic the needed information is accessed from one of the VLAN Membership Policy Servers VMPS specified in the vmpsTable Default value is static 1 Note The vlanPortAdminStatus cannot be set to dynamic 2 for a port which has portSecurityAdminStatus set to enabled 1 or for a port which currently has a vlanPortIslOperStatus of trunking 1 Syntax Integer static 1 The port is assigned to a VLAN statically default dynamic 2 The port is assigned to a VLAN dynamically Access Read write vianPortOperStatus vlanPortEntry 11 Indicates the current VLAN status of the port A status of inactive 1 indicates that a dynamic port does not yet have a VLAN assigned or that a static or dynamic port has been assigned a VLAN that is not currently active A status of active 2 indicates that the currently assigned VLAN is active A status of shutdown 3 indicates that the port has been shut down as a result of a VMPS response on a dynamic port Syntax Integer inactive 1 A dynamic port does not yet have a VLAN assigned or a static or dynamic port
39. ort on the module determines the value Valid entries are 1 to the value of moduleNumPorts for this module Syntax Integer 1 255 Access Read only portCrossIndex portEntry 3 Indicates a cross reference to the port s index within another MIB group The value is dependent on the type of port For an FDDI port the value corresponds to the snmpFddiPORTIndex Syntax Integer 1 4080 Access Read only portName portEntry 4 Specifies a descriptive string used by the network administrator to name the port Syntax DisplayString SIZE 0 20 Access Read write portType portEntry 5 Indicates the type of physical layer medium dependent interface on the port Syntax Integer other 1 None of the following cddi 2 CDDI unshielded twisted pair UTP FDDI fddi 3 Multimode fiber FDDI tppmd 4 ANSI standard UTP FDDI 2 30 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Port Group portType portEntry 5 Continued milt3 5 sddi 6 smf 7 el0BaseT 8 el0BaseF 9 scf 10 e100BaseTX 11 e100BaseT4 12 e100BaseF 13 atmOc3mmf 14 atmOc3smf 15 atmOc3utp 16 e100BaseFsm 17 e10al00BaseTX 18 mii 19 vlanRouter 20 Access Read only portOperStatus portEntry 6 MLT 3 UTP FDDI Shielded twisted pair STP FDDI Single mode fiber FDDI UTP Ethernet Multimode fiber Ethernet Small connector fiber FDDI UTP Fast Ethernet Catalyst 5000 series UTP Fast Ethernet
40. p 20 Indicates the time in hundredths of a second since the peak traffic meter value occurred Syntax TimeTicks Access Read only sysCommunityRwa systemGrp 21 When an SNMP message is received the community string in the message is compared to the sysCommunityRwa string first If it matches read write access is granted to all items in the MIB If it does not match the sys CommunityRw string is then compared Note This item is only accessible when using the community string defined in sysCommunityRwa Syntax DisplayString SIZE 0 20 Access Read write sysCommunityRw systemGrp 22 If the community string in the received SNMP message does not match the sysCommunityRwa string the message is then compared with the sysCommunityRw string If it matches read write access is granted to all items in the MIB except for restricted items such as community strings Restricted items appear empty when read and return a no such name error when an attempt is made to write them If it does not match the sysCommunityRo string is then compared Note This item is only accessible when using the community string defined in sysCommunityRwa 2 8 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference System Group sysCommunityRw systemGrp 22 Continued Syntax DisplayString SIZE 0 20 Access Read write sysCommunityRo systemGrp 23 If the community string in the received SNMP message does not
41. products that implement port monitoring functions monitorSourceModule monitorGrp 1 Specifies an index value that uniquely identifies the module where the monitoring source port is located A value of 0 indicates that the monitorSourcePort is really a source VLAN number Syntax Integer 0 16 Access Read write monitorSourcePort monitorGrp 2 Specifies an index value that uniquely identifies the monitoring source port within a module or the monitoring source VLAN Syntax Integer 0 1023 Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 37 Monitor Group monitorDestinationModule monitorGrp 3 Specifies an index value that uniquely identifies the module where the monitoring destination port is located Syntax Integer 1 16 Access Read write monitorDestinationPort monitorGrp 4 Specifies an index value that uniquely identifies the monitoring destination port within a module Syntax Integer 1 255 Access Read write monitorDirection monitorGrp 5 Specifies the type of packets to be monitored at the source port Syntax Integer transmit 1 receive 2 transmitAndReceive 3 default Access Read write monitorEnable monitorGrp 6 Enables or disables port monitoring Syntax Integer enabled 1 Port monitoring is enabled disabled 2 Port monitoring is disabled default Access Read write 2 38 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference
42. ries provides multicast router information per port or module sets the presence of an IP multicast router on this port to be determined statically or dynamically and sets whether Cisco Group Management Protocol CGMP is enabled on the device or not Implementation of the Multicast group is optional but within the group all the elements are mandatory mcastRouterTable multicastGrp 1 Contains a list of multicast router port entries The number of entries is determined by the number of ports in the system and includes the following variables mcastRouterModuleIndex mcastRouterPortIndex mcastRouterAdminStatus and mcastRouterOperStatus Syntax SEQUENCE OF McastRouterEntry Access Not accessible mcastRouterEntry mcastRouterTable 1 Contains multicast router information for a particular port Syntax McastRouterEntry Access Not accessible mcastRouterModuleIndex mcastRouterEntry 1 Provides an index value that uniquely identifies the module where this port is located see portModuleIndex Syntax Integer 1 16 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 51 Multicast Group mcastRouterPortIndex mcastRouterEntry 2 Provides an index value that uniquely identifies this port within a module see portIndex Syntax Integer 1 255 Access Read only mcastRouterAdminStatus mcastRouterEntry 3 Indicates whether the presence of an IP multicast router on this port is to be determined stati
43. ror is given enable 3 If the module status is configurable enables the module or else gives error disable 4 If the module status is configurable disables the module or else gives error Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 25 Module Group moduleName moduleEntry 13 Specifies the descriptive string used by the network administrator to name the module Syntax DisplayString SIZE 0 20 Access Read write moduleNumPorts moduleEntry 14 Indicates the number of ports supported by the module Syntax Integer 0 255 Access Read only modulePortStatus moduleEntry 15 Specifies a series of bytes containing status information about the module and each of the ports on the module The first byte contains the status for the module same value as moduleStatus and subsequent bytes contain status for the first through the last ports on the module same value as portOperStatus Syntax OCTET STRING SIZE 0 50 Access Read only moduleSubType moduleEntry 16 Indicates the type of daughterboard attached to this module Syntax Integer other 1 None of the following empty 2 Nothing installed wsf5510 3 EARL 1 2 26 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Module Group moduleSubType moduleEntry 16 Continued wsf5511 4 EARL 1 wsf5512 5 EARL 2 wsx5304 6 VIP I carrier Access Read only moduleModel moduleEntry 17 Indicates the manuf
44. sEnable dnsGrp 1 Enables or disables the DNS feature Syntax Integer enabled 1 DNS feature is enabled disabled 2 DNS feature is disabled default Access Read write dnsServerTable dnsGrp 2 Contains a list of a maximum of three DNS servers and includes the following variables dnsServerAddr and dnsServerType Syntax SEQUENCE OF DnsServerEntry Access Not accessible dnsServerEntry dnsServerTable 1 Contains a DNS server table entry Syntax DnsServerEntry Access Not accessible 2 54 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Domain Naming System Group dnsServerAddr dnsServerEntry 1 Provides the IP address of a DNS server Syntax IpAddress Access Read only dnsServerType dnsServerEntry 2 Removes adds or changes the priority level of a dnsServerTable entry To remove an entry from the dnsServerTable set this object to invalid 1 To add a new entry to the dnsServerTable set this object to primary 2 or other 3 for an IP address that is not already in the table If it is reachable the primary entry is used first Otherwise one of the other entries is used Setting one entry to primary 2 causes any previous primary entry to change to other 3 Syntax Integer invalid 1 Remove this entry primary 2 The primary entry other 3 A lower priority entry Access Read write End of Table dnsDomainName dnsGrp 3 Specifies the DNS domain name Syntax Display
45. ses can be displayed The following variables are included ipPermitDeniedAddress ipPermitDeniedAccess ipPermitDeniedTime Syntax SEQUENCE OF IpPermitDeniedListEntry Access Not accessible Catalyst 5000 Series Switch Workgroup MIBs 2 69 IP Permit List Group ipPermitDeniedListEntry ipPermitDeniedListTable 1 Provides an IP permit denied list table entry Syntax ipPermitDeniedListEntry Access Not accessible ipPermitDeniedAddress ipPermitDeniedListEntry 1 Indicates the IP address of an IP permit denied access Syntax IP address Access Read only ipPermitDeniedAccess ipPermitDeniedListEntry 2 Indicates the denied access type Syntax Integer telnet 1 snmp 2 Access Read only ipPermitDeniedTime ipPermitDeniedListEntry 3 Indicates the time in hundredths of a second since the IP permit denied access happened Syntax TimeTicks Access Read only End of Table 2 70 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Port Channel Group Port Channel Group The Port Channel group controls and manages variables that pertain to Ethernet Channeling functions such as port selection and status Implementation of the Port Channel group is optional but within the group all the elements are mandatory If the Port Channel feature is implemented the entire group must be implemented portChannelTable portChannelGrp 1 Contains a list of port channel entries and includes the following
46. ter Switch Link Syntax OCTET STRING SIZE 1 128 Access Read write Catalyst 5000 Series Switch Workgroup MIBs 2 41 VLAN Group vianPortSwitchLevel vlanPortEntry 6 Indicates the priority level the port uses to access the switching media Syntax Integer normal 1 high 2 default Access Read write vianPortIs AdminStatus vlanPortEntry 7 Indicates the administrative status set on the trunk port The operational status indicates whether the port is actually trunking or not If the status is set to on 1 or off 2 the port is permanently set to be a trunk or nontrunk respectively When the status is set to desirable 3 the port initiates a request to become a trunk and it becomes a trunk if another device s port on that link agrees When the status is set to auto 4 the port will become a trunk if it receives a request to become a trunk Note The status for 802 10 capable ports can only be either on 1 or off 2 and the default is off 2 The status for ISL capable ports can be any of the four and any change in status starts the negotiation process For ISL capable ports the default is auto 4 Syntax Integer on 1 The port is permanently set to be a trunk off 2 The port is permanently set to be a nontrunk desirable 3 The port initiates a request to become a trunk and it will become a trunk if another device s port on that link agrees auto 4 The port becomes a trunk if it re
47. try Access Not accessible 2 66 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Terminal Access Controller Access Control System Group tacacsServerAddr tacacsServerEntry 1 Indicates the IP address of a TACACS server Syntax IpAddress Access Read only tacacsServerType tacacsServerEntry 2 Removes or adds a tacacsServerEntry To remove an entry from the table set this object to invalid 1 To add a new entry to the tacacsServerTable set this object to primary 2 or other 3 for an IP address not already in the table If it is reachable the primary entry is used first Otherwise one of the other entries is used Setting one entry to primary 2 causes any previous primary entry to change to the other 3 Syntax Integer invalid 1 Remove this entry primary 2 The primary entry other 3 A lower priority entry Access Read write End of Table Catalyst 5000 Series Switch Workgroup MIBs 2 67 IP Permit List Group IP Permit List Group The IP Permit List group controls and manages variables that pertain to IP permit list functions such as access level and IP address of an IP Permit host Implementation of the IP Permit List group is optional but within the group all the elements are mandatory If the IP Permit List feature is implemented the entire group must be implemented ipPermitEnable ipPermitListGrp 1 Indicates whether the IP permit feature is enabled or disabled Syntax I
48. try 4 Provides the high part of the hardware version of the module For example if the hardware version is 3 1 the value of moduleHwHiVersion is 3 Syntax Integer 0 65535 Access Read only moduleHwLoVersion moduleEntry 5 Provides the low part of the hardware version of the module For example if the hardware version is 3 1 the value of moduleHwLoVersion is 1 Syntax Integer 0 65535 Access Read only moduleFwHiVersion moduleEntry 6 Provides the high part of the firmware version number For example if the firmware version is 3 1 the value of moduleFwHiVersion is 3 Syntax Integer 0 65535 Access Read only moduleFwLoVersion moduleEntry 7 Provides the low part of the firmware version number For example if the firmware version is 3 1 the value of moduleFwLoVersion is 1 Syntax Integer 0 65535 Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 23 Module Group moduleSwHiVersion moduleEntry 8 Provides the high part of the software version number For example if the software version is 3 1 the value of moduleSwHiVersion is 3 Syntax Integer 0 65535 Access Read only moduleSwLoVersion moduleEntry 9 Provides the low part of the software version number For example if the software version is 3 1 the value of moduleSwLoVersion is 1 Syntax Integer 0 65535 Access Read only moduleStatus moduleEntry 10 Provides the operational status of the
49. ult is a string which only has a value of 1 on its own port Syntax OCTET STRING SIZE 0 8 Access Read write portChannelAdminStatus portChannelEntry 4 Indicates the administrative status set on the channeled ports If status is set to on 1 channeling is enabled if set to off 2 channeling is disabled Syntax Integer on 1 Channeling is enabled off 2 Channeling is disabled default Access Read write 2 72 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference Port Channel Group portChannelOperStatus portChannelEntry 5 Indicates whether the current channeling operational status of a port is channeling or not channeling Syntax Integer channelling 1 Port is channeling notchannelling 2 Port is not channeling Access Read only Catalyst 5000 Series Switch Workgroup MIBs 2 73 Spanning Tree Status Group Spanning Tree Status Group The Spanning Tree Status group provides VLAN information Implementation of the Spanning Tree Status group is voluntary for all Cisco Workgroup Stack products cvbStpTable cvbStp 1 This table contains device Spanning Tree Protocol STP status information for each VLAN and includes the following variable cvbStpForwardingMap Syntax SEQUENCE OF CiscoVlanStpEntry Access Not accessible cvbStpEntry cvbStpTable 1 Device STP status for a specified VLAN Syntax CiscoVlanStpEntry Access Not accessible Note cvbStpEntry is not used
50. wing variables are available vlanPortModule vlanPort vlanPortVlan vlanPortls VlansAllowed vlanPortSwitchLevel vlanPortIslAdminStatus vlanPortlslOperStatus vlanPortIslPriority Vlans vlanPortAdminStatus and vlanPortOperStatus Syntax SEQUENCE OF VlanPortEntry Access Not accessible vlanPortEntry vlanPortTable 1 Contains VLAN information for a particular port on a module Syntax VlanPortEntry Access Not accessible vilanPortModule vlanPortEntry 1 Indicates an index value that uniquely identifies the module where this port is located see portModuleIndex Syntax Integer 1 16 Access Read only 2 40 Catalyst 5000 Series Switch Workgroup MIB User Quick Reference VLAN Group vianPort vlanPortEntry 2 Indicates an index value that uniquely identifies this port within a module see portIndex Syntax Integer 1 255 Access Read only vianPortVlan vlanPortEntry 3 Specifies the VLAN to which this port belongs Syntax Integer 0 1023 Access Read write Note vlanPortEntry4 is not used vianPortIsI ViansAllowed vlanPortEntry 5 Indicates which VLANs are allowed on this Inter Switch Link ISL It is an octet string value with bits set to indicate allowed VLANs It can be interpreted as a sum of f x as x goes from 0 to 1023 where f x 0 for VLAN x not allowed and f x exp 2 x for VLAN x allowed If all bits are 0 or the octet string is zero length the port is not operating as an In

Cisco WSX5111 Network Adapter

Contents

Download Pdf Manuals

Related Search

Related Contents