IBM Thinkvision L190P (Black) 19" LCD Monitor
Contents
1. Figure B 9 3 Connect the power cord to the monitor and then plug the power cord into a properly grounded outlet Next reconnect the power cords to your computer and all attached devices Switching on your monitor 10 1 2 Switch on your computer Switch on your monitor by pushing and releasing the power switch marked O at the front of the bezel To switch off your monitor push and release the power switch again To update or install device drivers follow the instructions in the Device driver installation section on page 11 If you are using the analog connector run Image setup by following the instructions in the Automatic Image setup section on page 14 Device driver installation ENGLISH Installing the device driver in Windows 95 or Windows 98 This section must be completed before continuing with the Windows 95 or Windows 98 Image setup on page 14 9 On LCD monitors unlike L CRTs a faster refresh rate does not improve display quality For optimal performance use either 1280 x 1024 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz To install the device driver in Microsoft Windows 95 or Windows 98 do the following Note Yo u must download files from the User s Guide and Installation Files CD to use the Plug and Play feature in Windows 95 or Windows 98 1 2 3 11 12 Turn off the computer and all attached devi2. OSD Icon Description Sub menu s Analog Digita Use this button to make the analog or Analo 19 42 digital connector active This feature 9 is used when two computers are Input Signal connected to the monitor The default 2 810 Image setting is analog 1 9 Properties 2 Digital f Options info rmation Display the detailed information of mode model name serial number and microcode The language chosen affects only the English language of the OSD Fran ais Select one of the six language to use Italiano Menu Language for the OSD Deutsch It has no effect on any software running on the computer 8 Changes the position of the OSD on Default Move at center on the screen n5 the screen Menu Position Custom eH eV e Save Reset should return all available Cancel functions apart from language which Reset should not change unless adjusted Factory Default via the Language menu to their factory presets di Change button repeat rate and menu Button Adjusts respondence speed time out setting repeat rate of button e Off Accessibility e Default e Slow Menu time out Adjusts the length of time for which the menu will stay on the screen before it disappears Exit Exits from current OSD menu 21 Further information Display modes your computer has l previously been used wi
3. only applies to the current screen mode When a new mode is selected repeat this section to reset the monitor 14 For digital input image setup is not required When you first use your monitor you must perform Auto Setup for analog input If you are using digital input continue with the instructions on page 9 This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing After you perform Auto Setup the settings are stored and used each time you turn on the monitor In order to optimize the displayed image a set up utility is provided on the IBM Monitor CD Operation of this utility is dependent on the operating system on your computer You may choose to run Image setup for each operating system that you use This means that if you sometimes use your monitor while running any version of Windows and sometimes also use it from within DOS not a DOS window you must run Image setup for both Windows and DOS You may run versions of Image setup in any order Before you begin Image setup for your computer make sure the computer video mode is set in the range of the supported screen resolution shown in the table on page 22 You should perform Image setup for each screen mode you use ENGLISH Image setup for DOS Ifthe monitor is in standby To set up the monitor automatically in DOS do the following L mode it may automatically turn off while you are waiting for
4. 1 it to warm up If this happens Turn on the monitor first then turn on the computer switch off the monitor and If the message check signal cable is displayed or if nothing is switch it on again after a few displayed check seconds 7 e That the video interface cable is not connected properly e The correct video adapter card is not installed e The correct supported display mode is selected for your computer e if you are using PC DOS V 2 Wait approximately 15 minutes for the monitor to warm up l change to U S mode by 3 Insert the User s Guide and Installation Files CD into the computer s typing CHEV US and pressing i enter at the command prompt CD ROM drive f 28295 4 Display the command prompt screen of the DOS full screen display P The size and diversity of the i l dot pattern varies with the 5 Type d TESTPAD where d is the letter of the CD ROM drive screen resolution 6 Press enter 7 Select the number for the color or text mode you want to set up 8 Select the number for the video mode you want to set up You can the flicker is minimized or hi f fth d vid d adjust it manually by following repeat this process for as many of the color and video modes as you refer to Manual Image setup on need SES 9 When the dot pattern appears press the lt button at the bottom of the monitor This activates the Auto setup procedure which will optimize the display settings with the provided dot patterns
5. 1280 x 1024 60 Hz 63 98 kHz 1280 x 1024 75 Hz 79 98 kHz Recommended D sub Analog only ENGLISH Power management To benefit from power management the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association VESA Display Power Management Signaling DPMS Standard The power management feature is invoked when the computer recognizes that you have not used your mouse or keyboard for a user definable period There are several states as described in the table below As an Energy Star 2000 Partner IBM has determined that this product meets the Energy Star 2000 guidelines for energy efficiency For optimal performance switch off your monitor at the end of each working day or whenever you expect to leave it unused for long periods during the day Power Restoring State Indicator Screen Operation Compliance On Steady green Normal Press a key or ENERGY Active off Steady amber Blank move the mouse STAR 2000 There may be a slight delay before the picture reappears Product disposal The fluorescent lamps in the liquid crystal display contain a small amount of mercury Dispose of it as required by local ordinances and regulations 23 Arm or wall mounting Removing the stand and cables Be sure to read the 1 Monitor Safety and Warranty Information manual that comes with your monitor before changing stands o
6. HG9 eerie eege 3 0 Mater Bias EE SN EE KEE 3 0 Meter 2 Sec 29 ENGLISH Notices and trademarks 30 This section contains information on notices and trademarks Notices IBM may not offer the products services or feature discussed in this document in all countries Consult your local IBM representative for information on the products and services currently available in your area Any reference to an IBM product program or service is not intended to state or imply that only that IBM product program or service may be used Any functionally equivalent product program or service that does not infringe any IBM intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any non IBM product program or service IBM may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to IBM Director of Licensing IBM Corporation North Castle Drive Armonk NY 10504 1785 U S A The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
7. L 0 Brightness Brightness Contrast 9 Adjusts contrast 9 9 Contrast gt O Moves the screen left and right Az Control Locked Image Horizontal Ss Position Position 3 Moves the screen up and down Az A Z Control Locked Vertical I Position G t 19 20 OSD Icon Description Sub menu s Controls and Adjustments Analog Digital Cd Image Setup Cd Automatic The Image setup function is used to adjust the level of noise in the video signal which causes horizontal lines or areas on the screen where the image appears to be unstable and jitters or shimmers This can be done automatically or manually If Auto is selected the image will automatically adjust Control Locked Sin If manual is selected the user will go Clock To adjust the Control Locked to the manual adjustment screen Phase focus of the Save display This Manual item allows you to remove any horizontal noise and clear or sharpen the image of characters GG Select the Color mode you find most Preset comfortable or fine tune the colors 65008 using the Custom menu if necessary Pink White Image Color e 7200K Properties Normal White e 9300K Blue White Custom eR Increases or decreases redness Increases or decreases G greenness Increases or decreases 5 blueness 9 Save ENGLISH Controls and Adjustments
8. NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some states do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication IBM may maker improvements and or changes in the product s and or the program s described in this publication at any time without notice IBM may use or distribute any for the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk ENGLISH Trademarks The following terms used in this publication are trademarks or service marks of the IBM Corporation in the United States other countries or both IBM IBM logo ThinkPad ENERGY STAR and the ENERGY STAR logo are U S Govt registered trademarks Microsoft Windows and Windows NT are trademarks of Microsoft Corporation in the United States other countries of both Other company product and service names may be trademarks or service m
9. The screen will momentarily turn black while auto adjustment proceeds 10 When finished the Image setup message disappears and the screen returns to a normal display 11 To clear the Image setup test pattern press the Esc key on your keyboard 12 Type Exit at the command prompt to return to Windows gt Ifthe screen flickers repeat l the setup several times until If you use other operating systems perform the appropriate Auto setup for those systems using instructions given in Image setup Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP on page 16 15 Image setup for Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP Ifthe monitor is in standby L mode it may automatically turn off while you are waiting for it to warm up The size and diversity of the dot pattern varies with the screen resolution 16 To set up the monitor automatically in Windows 95 Windows 98 Windows NT Windows 2000 Windows Me or Windows XP do the following 1 Turn on the monitor first then turn on the computer If the message check signal cable is displayed or if nothing is displayed check e That the video interface cable is not connected properly The correct video adapter card is not installed The correct supported display mode is selected for your computer 2 Wait approximately 15 minutes for the monitor to warm up 3 Ifthe icon bar and tool bar are displayed dra
10. cannot insert the plug into the outlet contact an electrician for an approved outlet adapter or to replace the outlet with one that enables this safety feature Never overload an electrical outlet The overall system load should not exceed 80 percent of the branch circuit rating Consult an electrician for more information if you have questions about power loads and branch circuit ratings Be sure that the power outlet you are using is properly wired easily accessible and located close to the equipment Do not fully extend power cords in a way that will stress the cords Connect and disconnect the equipment from the electrical outlet carefully All IBM personal computers contain a non rechargeable coin cell battery to provide power to the system clock In addition many mobile products such as ThinkPad notebook PCs utilize a rechargeable battery pack to provide system power when in portable mode Batteries supplied by IBM for use with your product have been tested for compatibility and should only be replaced with IBM approved parts Never attempt to open or service any battery Do not crush puncture or incinerate batteries or short circuit the metal contacts Do not expose the battery to water or other liquids Only recharge the battery pack strictly according to instructions included in the product documentation Battery abuse or mishandling can cause the battery to overheat which can cause gasses or flame to vent from the battery pack or coi
11. select color combinations which can help you to view in comfort See the User controls section on page 18 for more information Caring for your monitor Be sure to turn off the power before you perform any maintenance on the monitor Clean your monitor as follows Do not use solvents or abrasives e Gently wipe the covers and the screen with a soft cloth e Remove finger marks and grease with a damp cloth and mild detergent e Never use flammable cleaning materials to clean your IBM monitor or any other electrical apparatus ENGLISH Connecting your monitor Be sure to read the Safety 1 Turn off your computer and all attached devices Next unplug all power Information located in the cords to your computer and all attached devices Monitor Safety and Warranty Information Manual before 2 Connect the signal cable cariying Out tnis procedure The analog signal cable is already connected to your monitor See in Figure A e When connecting the analog signal cable connect the free end of the attached signal cable to the 15 pin monitor port on the computer and tighten screws Figure A If you are connecting a DVI D digital signal cable follow Figure B Connect one end of the monitor signal cable to the white connector on the rear panel of the monitor Connect the other end to the white connector on the rear panel of the computer and tighten the screws
12. select the maximum refresh rate and corresponding Color Matching Profiles i Installing the device driver in Windows 2000 or Windows Me This section must be completed before continuing with the Windows 2000 Windows Me Image setup on page 14 On LCD monitors unlike l CATs a faster refresh rate does not improve display quality For optimal performance use either 1280 x 1024 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz 12 To install the device driver in Microsoft Windows 2000 Professional or Microsoft Windows Millennium Edition Me do the following Note You must download files from the User s Guide and Installation Files CD to use the Plug and Play feature in Windows 2000 or Windows Me 1 2 3 o mm 4 gt 1 12 13 14 1 16 17 Turn off the computer and all attached devices Ensure that the monitor is connected correctly Turn on the monitor and then the system unit Allow your computer to start the Windows 2000 or Windows Me operating system Open the Display Properties window by clicking Start gt Settings gt Control Panel and then double clicking on the Display icon Click the Settings tab Click the Advanced button Click the Monitor tab Click the Properties button Click the Driver tab Open the Upgrade Device Driver Wizard window by clicking on Update Driver and then click the Next button Sel
13. IBM ThinkVision Monitor L180p 8 L180p English User s Guide First Edition January 2004 Note For important information refer to the Monitor Safety and Warranty manual that comes with this monitor Contents Safety Read first wssciccsscncsieccasuvatdteiviuswtusentseteceucdeucwassvadavastauantinsassboesdewletwewewssuesdlavins 2 Setting up the MONMON zeuesegeuggesteeEeseueeREeEEEEU KEES aani 488 5 8 5 Product description E 5 Handling ld ee 5 ln Deele lee 6 Workplace preparation 7 Adjusting the monitor position 7 MV ORKING EH 8 Klee dee 6 Connecting your 1 1161411 91 7 9 8 hones 9 Switching on your le e EE 10 DEVICE driver installation ssai iaieiiea 11 le ele 11 Windows ZOO IM i cae 6 12 ee E 13 Automatic Image setup nnmnnn nnmnnn nnna 14 101119 12 1 1 9 taan e ee 14 Image setup for Kl 15 Image setup for Windows 95 Windows 98 Windows 2000 Windows NT Windows Me or Windows XP 16 Manual E EE TT WE 17 Adju
14. Start gt Settings gt Control Panel and then double clicking on the Display icon Click the Settings tab Click the Advanced button Click the Monitor tab Click the Properties button Click the Driver tab Open the Hardware Update Wizard window by clicking on Update Driver and then click the Next button Select Install from a list or Specific location Advanced and then click the Next button Insert the Monitor CD into the CD drive and click the Have Disk button Click OK Ensure that the CD drive letter is selected and then select the DRIVERS folder Select IBM L180p monitor and click OK The files will be copied from the CD to your hard disk drive Close all open windows and remove the CD Restart the computer The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles 13 Automatic Image setup CO Image setup Before carrying out this section it is very important that the correct monitor drivers have been installed See pages 11 and 13 E The Setup Utility included l on the setup CD displays a test pattern of dots It does not replace or modify the display drivers ZS The Image setup L instructions require the monitor to be warmed up for 15 minutes This is not required for normal operation If your computer does not L run with the setup CD shipped with the monitor refer to Manual Image setup on page 17 The Image setup process
15. arks of other Copyright International Business Machines Corporation 2004 All rights reserved 31
16. ces Ensure that the monitor is connected correctly Turn on the monitor and then the system unit Allow your computer to start the Windows 95 or Windows 98 operating system Your computer s Plug and Play code might warn you that your system hardware has changed This means that it has detected your new monitor for the first time Open the Display Properties window by clicking Start gt Settings gt Control Panel and then double clicking on the Display icon Click the Settings tab If you are using Windows 95 complete the following steps a Click the Change Display Type button b Click the Change Monitor Type button c Proceed to Step 7 If you are using Windows 98 complete the following steps a Click the Advanced button b Click the Monitor tab c Open the Update Device Driver Wizard window by clicking on the Change button and then select the Next button d Select Display a list of the known drivers for this device so that can choose a specific driver and then select the Next button e Proceed to Step 7 Insert the User s Guide and Installation Files CD into the CD drive and click the Have Disk button Click OK Ensure that the CD drive letter is selected and then select the DRIVERS folder Select IBM L180p monitor and click OK The files will be copied from the CD to your hard disk drive Close all open windows and remove the CD Restart the computer The system will automatically
17. ect Display a list of the known drivers for this device so that can choose a specific driver and then click the Next button Insert the Monitor CD into the CD drive and click the Have Disk button Click OK Ensure that the CD drive letter is selected and then select the DRIVERS folder Select IBM L180p monitor and click OK The files will be copied from the CD to your hard disk drive Close all open windows and remove the CD Restart the computer The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles ENGLISH Installing the device driver in Windows XP This section must be completed before continuing with the Windows XP Image Setup on page 14 On LCD monitors unlike L CRTs a faster refresh rate does not improve display quality For optimal performance use either 1280 x 1024 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz To install the device driver in Windows XP do the following Note You must download files from the User s Guide and Installation Files CD to use the Plug and Play feature in Windows XP 4 2 3 2 RO OOO 3 a ech 12 13 14 15 16 17 Turn off the computer and all attached devices Ensure that the monitor is connected correctly Turn on the monitor and then the system unit Allow your computer to start the Windows XP operating system Open the Display Properties window by clicking
18. entative Troubleshooting If you have a problem setting up or using your monitor you may be able to solve it yourself Before calling your retailer or IBM try the suggested actions that are appropriate to your problem software on your computer Press the 4 to switch between analog and digital mode If the panel is the wrong mode for the signal being provided the monitor appears to go into sleep mode Problem possinle Suggested Action Reference Cause Screen is No power jo e Ensure that the electrical outlet Connecting blank and monitor and the monitor are both your Monitor power switched on section on indicator is off e Check that the power cord page 9 is firmly plugged into the electrical outlet and the power supply unit e the power cord plug has a removable fuse replace it e Try another power cord e Try another electrical outlet e Check the power connection at the back of the panel Screen is blank Brightness e Adjust brightness and contrast User and power and Contrast Controls indicator is may be too section on steady green low page 18 Screen is blank The monitor is e Press any key on the keyboard Power and power in the Power or move the mouse to restore Management indicator is Management operation section on steady amber Standby state e Check the Power Management page 23 25 ENGLISH 9 For image problems you l may want to run Image
19. g them to the bottom of the screen 4 Insert the User s Guide and Installation Files CD into the computer s CD ROM drive 5 Check the operating system installed on your computer and follow the instructions from the table below Operating system installation steps Operating 1 Step 2 Step 3 System Step Windows 95 Open program manager Windows 98 d g Type e TESTPAT where e is Windows 2000 Select Select the letter of your CD ROM drive Windows NI START RUN then press Enter Windows Me or f Windows XP 6 When the dot pattern appears press the GQ button at the bottom of the monitor This activates the Image setup procedure which will optimize the display settings with the provided dot patterns The screen will momentarily turn black while auto adjustment proceeds 7 When finished the Image setup message disappears and the screen returns to a normal display 8 Toclear the Image setup test pattern press the Esc key on your keyboard You have completed the monitor setup for Windows If you are using the DOS operating system go to Image setup for DOS on page 15 Manual Image setup If the monitor is in standby mode it might automatically turn off while you are waiting for it to warm up Normally you can complete the setup procedure using Automatic Image setup however if your screen image is still distorted after you perform Image Setup or the setup CD does not run
20. n cell If your battery is damaged or if you notice any discharge from your battery or the buildup of foreign materials on the battery leads stop using the battery and obtain a replacement from the battery manufacturer Batteries can degrade when they are left unused for long periods of time For some rechargeable batteries particularly Lithium lon batteries leaving a battery unused in a discharged state could increase the risk of a battery short circuit which could shorten the life of the battery and can also pose a safety hazard Do not let rechargeable Lithium lon batteries completely discharge or store these batteries in a discharged state Computers generate heat when turned on and when batteries are charging Notebook PCs can generate a significant amount of heat due to their compact size Always follow these basic precautions e Do not leave the base of your computer in contact with your lap or any part of your body for an extended period when the computer is functioning or when the battery is charging Your computer produces some heat during normal operation Extended contact with the body could cause discomfort or potentially a skin burn Do not operate your computer or charge the battery near flammable materials or in explosive environments Ventilation slots fans and or heat sinks are provided with the product for safety comfort and reliable operation These features might inadvertently become blocked by placing the produc
21. ns Do not support the monitor within the screen area The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure 1 Lift the monitor by placing your hands where indicated by the arrows in the figure below An alternative is to use the handle feature on the back of the monitor See Figure A below 2 Before using your monitor for the first time remove the clear protective film from the front of the screen 3 Before adjusting your monitor for the first time remove the locking clip on rear of the stand Carefully hold the screen of the monitor and squeeze the locking clip to remove This action is shown in Figure A Figure A Kensington security slot This slot can be used to connect to a locking cable Locking cables can be purchased separately at most computer stores Kensington security slot Workplace preparation This section gives advice Height on what you should consider before you set up Position the monitor so that the top of the screen is slightly below your eye your monitor level when you sit at your workstation Orientation 1 Choose a position that gives the least reflection from lights and windows usually at a right angle to any windows 2 Positon the monitor directly in front of you so that you do not have to twist your body to use it 3 Tilt the monitor to a comfortable viewing angle Adjusting the monito
22. on your system perform Manual Image Setup To manually adjust the image setting do the following 1 Turn on the monitor and wait approximately 15 minutes for it to warm up Display the image you most frequently use on the screen Press the OSD Enter button at the bottom of the monitor to display the initial OSD menu 4 Use the Right Arrow button to select the Image setup icon 00 and press the OSD Enter button to access the function 5 Use the Right Arrow button to select to manual Press the OK button twice to select clock 6 Use the Arrow buttons to manually adjust to correct for jitter or noise in the image Press OK button 7 Press OK and use Arrow buttons to adjust phase press OK Press OK 41 again to Save and Exit Then press Exit button C gt twice to exit OSD You have completed the monitor setup 17 ENGLISH Adjusting your LCD monitor User controls e The image is already L optimized for many display modes however the user controls can be used to adjust the image to your liking The settings are saved l after adjustment and when exiting the OSD and will be effective thereafter 18 ThinkVision USER CONTROL FEATURES Icon Monitor controls O Switches the monitors on and off lt l Display main OSD menu and selects highlighted menu item and Moved the cursor to highlight icons or make adjustments Exi
23. osition 449 7mm 17 70 in Width 396 0mm 15 59 in Depth 259 0mm 10 19 in Weight Without Stand 5 3 kg 11 684 Ibs With Stand 7 7 kg 16 975 155 Image Viewable Image Size 18 1inch 459 74 mm Maximum Height 389 mm Maximum Width 317 2 mm Pixel Pitch 0 28 mm H x 0 28 mm V Power Input Supply Voltage 100 240 Vac 60 50 3Hz Rated Current 1A Power Normal Operation lt 55 Consumption Active off lt 3W Off lt 3W Video Input Input Signal Analog 75 ohm 0 7V Digital DVI 1 0 Horiz Addressability 1280 pixels max Vert Addressability 1024 lines max Clock Frequency 108 MHz Digital 135 MHz Analog Sync Input Type Analog Separate Composite SOG Digital DVI 1 0 Communications VESA DDC E DDC Supported Display Standard modes IBM VESA MAC Modes Horiz Frequency Vert Frequency Analog 31 81 KHz Analog 55 75 Hz Environment Temperature Operating Storage Shipping Humidity Operating Storage Shipping 10 to 35 C 20 to 60 C 20 to 60 C 10 to 80 5 to 95 5 to 95 Service information The following parts are for use by IBM service or IBM authorized dealers to support the customer warranty Parts are for service use only Model Type 9180 P N Description Video Color MTM Geography 73P2737 FRU Monitor Hybrid Black 9180 HB9 WW 73P2740 FRU Stand Hybrid Black 9180 HB9 ww 9180
24. r cables 24 Alternative stands for your IBM Flat Panel Monitor may be available from specialist suppliers This product is equipped with mounting facilities that conform to the VESA Flat Panel Monitor Physical Mounting Interface Standard FPMPMI When using the VESA standard mounting plate connect the monitor to the wall or to the arm mounting device Use other cables for reasons such as having the monitor wall mounted follow the instructions below 1 Power off the monitor Next disconnect the power cord and then the signal cable to the monitor 2 Lay the monitor facedown on a cushion and remove the four screws holding the hinge mechanism on the monitor Refer to the diagram below for additional information on how to remove the stand 3 You have to use the four screw holes on the bottom of the stand to attach the monitor to the surface of wall For additional information see the instructions supplied with the purchased arm 4 Locate a place to which you want to attach the monitor When locating the place you have to consider the lengths of the signal cable and the power cord 5 Place the monitor in the location you selected in the step 4 Next reconnect the signal cable and then the power cord to the monitor To obtain the correct cables and or to get further instructions on installing them call the IBM Support Center at the above numbers or contact your dealer retailer or other IBM authorized service repres
25. r position E With the IBM Flat Panel l Monitor you can adjust its Viewing angle position in various ways for 1 maximum comfort You can tilt the screen forward and backward as shown below in Figure A Swivel You can swivel the screen to the left or the right as shown below in Figure A Height You can adjust height of the screen as shown below in Figure B Figure A Figure B ENGLISH Working practices This section gives advice on how you can work comfortably and reduce fatigue Rest Take regular breaks Vary your posture stand up and stretch occasionally as prolonged use of computer workstations can be tiring Back Sit back in your chair and use the backrest Hands Use a light touch on the keyboard and keep your hands and fingers relaxed Your upper arms should be relaxed with your elbows near your body Use a light touch on the keyboard keeping your hands and fingers relaxed Allow a space in front of the keyboard to rest your wrists when not typing Consider using a wristpad Eyesight Working with monitors in common with any prolonged close work can be visually demanding Look away from the screen periodically and have your eyesight checked regularly Screen settings Set the screen brightness and contrast to a comfortable level You may have to adjust these settings as the lighting changes during the day Many application programs let you
26. setup again before consulting to this section In most cases Image setup can fix the problems See Automatic Image setup for the computer on page 14 for details 26 Possible Problem Cause Suggested Action Reference Screen is blank Display mode of e Reconfigure key on the Futher and power the computer is computer to use a supported Information indicator is outside the display mode section on flashing green range of the page 22 every 0 5 monitor second CHECK The monitor is e Check that the signal cable Connecting SIGNAL CABLE not receiving a is firmly connected to the your monitor message is video signal computer section on shown and e Check that no pins are bent page 9 power indicator in the signal cable connector is steady amber Image appears There are 0869 Select Image setup menu User P to be smeared in the video in the OSD Then select Controls signal Manual to adjust Clock Phase Section on settings page 20 ina s User ge appears The color setting e Adjust the Color settings Controls to be discolored may be incorrect Se S section on page 20 A few dots are missing discolored or inappropriately lighted A small number of missing discolored or lighted dots may be present on the screen which is an intrinsic characteristic of the TFT LCD technology and is not an LCD defect ENGLISH Help and service information If possible
27. stay by your l computer Your Technical Support Representative may wish to go through the problem with you during the call E More help late breaking news and details of the latest accessories for these products may be found on the worldwide web at http www pc ibm com us accessories If you are unable to correct the problem yourself you may seek further help as follows Call the IBM Service and Support In the U S A and Puerto Rico call 1 800 772 2227 In Canada Toronto only call 416 383 3344 In Canada all other call 1 800 565 3344 In other countries contact your dealer retailer or other IBM authorized service representative Before calling please have available as much of the following information as possible Model and serial number from the label on your monitor Purchase receipt Description of problem Computer type and model System configuration hardware fitted etc System BIOS version number Operating System and version number Display driver version number 62 62 941160 En SJ gt Video Adapter Type 27 Specifications Power consumption figures are for the monitor and the power supply combined 28 This color monitor Type model 9180 Hxx uses a 18 1 inch TFT LCD Without Stand With Stand Height Width Depth 330 5mm 13 01 in 396 0mm 15 59 in 71 1mm 2 79 in Height Lowest Position 349 7mm 13 76 in Height Highest P
28. sting your LCD monitor E 18 ULTI EE E A 18 On screen display OSD controls 19 Further information 22 Display mode Saina Ee g 22 Power MANAGING eene 23 gelee Ee EE 23 Armor EUR eu 24 lee te E e te 25 Help and service ee 27 SpecificatioNS aaea araea aa 28 Service information 29 Notices and TAGCINAIKS isc 30 ENGLISH Safety Read first Before installing this product read the Safety Information Avant d installer ce produit lisez les consignes de s curit Vor der Installation dieses Produkts die Sicherheitshinweise lesen eyKataotroEete To mpoidv aut SiaBdote TIG MANPOM opies ao paAEiac safety information TNN703N MXIT NX WIP IT WN Wpnnw 397 A term k telep t se el tt olvassa el a Biztons gi el r sokat Prima di installare questo prodotto leggere le Informazioni sulla Sicurezza Antes de instalar este produto leia as Informa es de Seguran a L s s kerhe
29. t on a bed sofa carpet or other flexible surface Never block cover or disable these features CD and DVD drives spin discs at a high speed If a CD or DVD is cracked or otherwise physically damaged it is possible for the disc to break apart or even shatter when the CD drive is in use To protect against possible injury due to this situation and to reduce the risk of damage to your machine do the following e Always store CD DVD discs in their original packaging Always store CD DVD discs out of direct sunlight and away from direct heat sources e Remove CD DVD discs from the computer when not in use e Do not bend or flex CD DVD discs or force them into the computer or their packaging Check CD DVD discs for cracks before each use Do not use cracked or damaged discs Setting up the monitor ENGLISH Product description The IBM ThinkVision Monitor L180p is a TFT LCD Color Monitor It requires a computer with a suitable on board sub system or Video Adapter card that can support SXGA 1280 x 1024 XGA 1024 x 768 SVGA 800 x 600 or VGA 640 x 480 at 60Hz In addition to your monitor your option package includes the following User s Guide and Installation Files CD e Monitor Safety and Warranty Information Manual IBM ThinkVision Monitor L180p Setup Guide e Power Cord e L180p ThinkVision Monitor Analog Interface Cable Attached to Monitor Digital Interface Cable not Attached to Monitor Handling instructio
30. th a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display you may need to re attach the CRT monitor temporarily until you have reconfigured the computer preferably to 1280 x 1024 at 60Hz Note VESA timings are as detailed in the VESA Display Monitor Timing Specification Version 1 0 Revision 0 8 Dated 09 17 98 22 The display mode the monitor uses is controlled by the computer Therefore you should refer to your computer documentation for details on how to change display modes The image size position and shape may change when the display mode changes This is normal and the image can be readjusted using Image setup and the monitor controls Unlike CRT monitors which require a high refresh rate to minimize flicker TFT technology is inherently flicker free If possible configure your computer for 1280 x 1024 addressability at 60Hz vertical refresh rate For the display modes listed below the screen image has been optimized during manufacture Factory Set Display Modes Addressability Refresh Rate Horizontal Frequency 640 x 480 60 Hz 31 5 kHz 640 x 480 75 Hz 37 5 kHz 640 x 350 70 Hz 31 5 kHz 720 x 400 70 Hz 31 5 kHz 800 x 600 60 Hz 37 9 kHz 800 x 600 75 Hz 46 9 kHz 832 x 624 75 Hz 49 7 kHz 1024 x 768 60 Hz 48 4 kHz 1024 x 768 75 Hz 60 0 kHz 1152 x 870 75 Hz 68 7 kHz 1152 x 900 66 Hz 61 8 kHz
31. the IBM Support Center Use only an IBM authorized service provider who is approved to repair your particular product Note Some parts can be upgraded or replaced by the customer These parts are referred to as Customer Replaceable Units or CRUs IBM expressly identifies CRUs as such and provides documentation with instructions when it is appropriate for customers to replace those parts You must closely follow all instructions when performing such replacements Always make sure that the power is turned off and that the product is unplugged from any power source before you attempt the replacement If you have any questions or concerns contact the IBM Support Center Use only the power cords and power adapters supplied by the product manufacturer Never wrap a power cord around the power adapter or other object Doing so can stress the cord in ways that can cause the cord to fray crack or crimp This can present a safety hazard Always route power cords so that they will not be walked on tripped over or pinched by objects Protect the cord and power adapters from liquids For instance do not leave your cord or power adapter near sinks tubs toilets or on floors that are cleaned with liquid cleansers Liquids can cause a short circuit particularly if the cord or power adapter has been stressed by misuse Liquids can also cause gradual corrosion of the power cord terminals and or the connector terminals on the adapter which can eventually res
32. ts from current OSD menu Icon Direct Access Functions Bring up Brightness adjustment gt Executes automatic image setup CONTROLS LOCK UNLOCK This feature allows you to secure the current control settings while allowing the user to adjust Brightness so that they cannot be inadvertently changed Push and hold the enter button d for 10 seconds the message Menu is Locked appears You can unlock the OSD controls at any time by pushing the enter button for 10 seconds the message Menu is Unlocked will appear Switch between input signals ENGLISH On screen display OSD controls S The LCD monitor needs l time to become thermally stable the first time you turn it on each day Thus to achieve more accurate adjustments for The settings adjustable with the user controls are viewed through the On Screen Display OSD Press the enter button to display the main OSD menu Initial appearance of OSD parameters allow the LCD Main menu monitor to warm up for at least H ao gt 15 pee any Brightness Contrast screen adjustment O Sub menu Adjustment screen k 02 SH Brightness Contrast w o Brightness S Adjusts overall screen brightness Cancel OSD functions ae Control and Adjustments OSD Icon Description Sub menus J Analog Digital ZK xt Adjusts brightness
33. tsinformationen innan du installerar den h r produkten Prije instalacije ovog produkta obavezno pro itajte Sigurnosne Upute Les sikkerhetsinformasjonen Safety Information f r du installerer dette produktet Przed zainstalowaniem tego produktu nale y zapozna si z ksi k Informacje dotycz ce bezpiecze stwa Safety Information Ipex ga ce HHCTasMpa OBOj NPOAYKT NpowutajTre au popmayajara 38 6e356egHocT Pred in tal ciou tohto zariadenia si pre taje Bezpe nostn predpisy Pred namestitvijo tega proizvoda preberite Varnostne informacije Ennen kuin asennat t m n tuotteen lue turvaohjeet kohdasta Safety Information P ed instalac tohoto produktu si p e t te p ru ku bezpe nostn ch instrukc FEES ASE TZ TA Safety Information ZPR A RERA RL WAM RARA ADE Colo bel ra L s sikkerhedsforskrifterne for du installerer dette produkt Sib 7 Sa REWRMABMA lt ESL MSZE 3 1 6 2 AO Sa SES ASAAEe Antes de instalar este producto lea la informacion de seguridad Antes de instalar este produto leia as Informa es de Seguran a Nepeg ycTaHoBKON npogyKTa NPOYTUTE WHCGTDNKLUa DO TexHuKe GesonacHocTu Lees voordat u dit product installeert eerst de veiligheidsvoorschriften ENGLISH Always observe the following precautions to reduce the risk of injury and property damage Do not attempt to service a product yourself unless instructed to do so by
34. ult in overheating Always connect power cords and signal cables in the correct order and ensure that all power cord connectors are securely and completely plugged into receptacles Do not use any power adapter that shows corrosion at the ac input pins and or shows signs of overheating Such as deformed plastic at the ac input or anywhere on the power adapter Do not use any power cords where the electrical contacts on either end show signs of corrosion or overheating or where the power cord appears to have been damaged in any way Ensure that extension cords surge protectors uninterruptible power supplies and power strips that you use are rated to handle the electrical requirements of the product Never overload these devices If power strips are used the load should not exceed the power strip input rating Consult an electrician for more information if you have questions about power loads power requirements and input ratings If a receptacle power outlet that you intend to use with your computer equipment appears to be damaged or corroded do not use the outlet until it is replaced by a qualified electrician Do not bend or modify the plug If the plug is damaged contact the manufacturer to obtain a replacement Some products are equipped with a three pronged plug This plug fits only into a grounded electrical outlet This is a safety feature Do not defeat this safety feature by trying to insert it into a non grounded outlet If you
Download Pdf Manuals
Related Search