Sony SDM-HX93 19" LCD Monitor
Contents
1. The installation of your monitor is complete If necessary use the monitor s controls to adjust the picture page 12 continued 9 If no picture appears on your screen Check that the power cord and the video signal cable are properly connected f NO INPUT SIGNAL appears on the screen The computer is in the power saving mode Try pressing any key on the keyboard or moving the mouse Check that the input signal setting is correct by pressing the INPUT button page 11 If CABLE DISCONNECTED appears on the screen Check that the video signal cable is properly connected Check that the input signal setting is correct by pressing the INPUT button page 11 e If OUT OF RANGE appears on the screen reconnect the old monitor Then adjust the computer s graphics board within the following ranges Analog RGB Digital RGB Horizontal frequency 28 80 kHz 28 64 kHz Vertical frequency 48 75 Hz 60 Hz Resolution 1280 x 1024 or less 1280 x 1024 or less For more information about on screen messages see Trouble symptoms and remedies on page 22 No need for specific drivers The monitor complies with the DDC Plug amp Play standard and automatically detects all the monitor s information No specific driver needs to be installed on the computer The first time you turn on your computer after connecting the monitor the2. da v P na de cues os 13 Adjusting the BACKLIGHT O 13 Adjusting the CONTRAST M ics bie a k ry i a t rentes 13 Adjusting the BRIGHTNESS XQ 14 Adjusting the GAMMA 7 14 Adjusting the COLOR S 14 Adjusting the SHARPNESS 14 AUDIO menu E uu a dpa ace pone Cone nore v deir ios 15 Adjusting TREBLE BASS or BALANCE 15 Adjusting SURROUND zs s 5x ice m t RR einn 15 MODE RESET menu D ccce resetting every mode to the default 15 Apple Computer Inc registered in the A SCREEN menu analog RGB signal only Lm 16 U S A and other countries MENU POSITION menu 17 NE S ccs PU aren b lt b desee Te Bend gt INPUT SENSING ON OFF menu 17 States and other countries LANGUAGE menu nh 18 gt A A v are A gt lt RESET menu reset to the default setting 18 trademarks of IBM Corporation of the DS On MENU LOCK menu 4 544044 ar thule aed Oe a 18 VESA and DDC are trademarks of the wk O o Video Electronics Standards Tech n ical Featu res EH EH NH NH H H NH H H H H H H H NH H H NH mn NH NH 1 9 Association e ENERGY STAR isa U S registered Controlling the volume Fon 3 3 3 0 3 3 33 73 93 9 9 O s x 19 mark Power saving function 19 Adobe and
3. setup Wizard may appear on the screen In this case follow the on screen instructions The Plug amp Play monitor is automatically selected so that you can use this monitor The vertical frequency is set to 60 Hz Since flickers are unobtrusive on the monitor you can use it as it is You do not need to set the vertical frequency to any particular high value 10 Setup 6 Adjust the tilt and swivel This monitor can be adjusted within the angles shown below Grasp the sides of the LCD panel then adjust screen angles approx approx approx 45 approx X To use the monitor comfortably Adjust the viewing angle of your monitor according to the height of your desk and chair and so that light is not reflected from the screen to your eyes Note When adjusting the screen tilt and height proceed slowly and carefully being sure not to hit the monitor against the desk Selecting the input signal INPUT button Press the INPUT button The input signal change each time you press this button INPUT On screen message Input signal configuration Appears about 5 seconds on the upper left corner INPUTI HD15 HD15 input connector analog RGB for INPUTI INPUT2 HD15 HD15 input connector analog RGB for INPUT2 INPUTS DVI D DVI D input connector digital RGB for INPUT3 11 Customizing Your Monitor Before making adjus
4. Acrobat are trademarks of Setting the MODE PICTURE AUDIO g mode 20 iem Sce ad m Automatic brightness adjustment function light sensor 20 trademarks of SRS Labs Inc Automatic picture quality adjustment function WOW technology is incorporated under analog RGB signal only a a 3 1 ached oie acre dura n i dearest ane 20 license from SRS Labs Inc All other product names mentioned H enm Det Troubleshooting 21 SL On screen messages 21 companies Pudthernore and O arbor Trouble symptoms and remedies 22 mentioned in each case in this manual Self diagnosis function aa uc nca aao DR edem oC e EISE 24 Specifications 25 Precautions Warning on power connections Use the supplied power cord If you use a different power cord be sure that it is compatible with your local power supply For the customers in the U S A If you do not use the appropriate cord this monitor will not conform to mandatory FCC standards For the customers in the UK If you use the monitor in the UK be sure to use the appropriate UK power cord Example of plug types for 100 to 120 V AC for 200 to 240 V AC for 240 V AC only The equipment should be installed near an easily accessible outlet Installation Do not install or leave the monitor n places subject to extreme temperatures for exam
5. HT Cu CONTRAST O 2 PICTURE AUDIO menu You can adjust the following items using PICTURE AUDIO MODE BRIGHTNESS GAME MOVIE PC AUTO GAMMA menu Y PICTURE 2 e COLOR menu AUDIO q e SHARPNESS pot e MODE RESET gt lt 1280x1024 60Hz Adjusting the BACKLIGHT If the screen is too bright adjust the backlight to make the screen easier to see E MODE menu You can select the appropriate screen brightness for your purpose 1 Press the MENU button The PICTURE AUDIO settings can be set for each mode The main menu appears on the screen The changed setting is automatically applied for each input INPUTVIINPUTZ INPUT 2 Press the 4 button to select g PICTURE AUDIO and press the OK button 1 Press the MENU button The PICTURE AUDIO menu appears on the screen The main menu appears on the screen 3 Press the V f buttons to select g PICTURE and 2 Press the V f button to select g PICTURE press the OK button AUDIO and press the OK button The PICTURE menu appears on the screen The PICTURE AUDIO menu appears on the screen 4 Press the 4 4 buttons to select BACKLIGHT 3 Press the V f button to select MOVIE and press and press the OK button GB the OK button The BACKLIGHT menu appears on the screen The MODE menu appears on the screen 5 Press the 4 4 buttons to adjust the light level and GAME press the OK button MOVIE AUTO Adjusting the CO
6. Minimum 7 A 125 V NOTICE Cette notice s applique aux Etats Unis et au Canada uniquement Si cet appareil est export aux Etats Unis ou au Canada utiliser le cordon d alimentation portant la mention UL LISTED CSA LABELLED et remplissant les conditions suivantes SPECIFICATIONS Type de fiche Fiche Nema 5 15 broches Cordon Type SVT ou SJT minimum 3 x 18 AWG Longueur Maximum 15 pieds Tension Minimum 7 A 125 V As an ENERGY STAR Partner Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency Table of Contents http www sony net Precautions auus i o woh ae he wd os dee ee n eor ae 4 Identifying parts and controls 5 S eii o D neve kan eee oe Oe cea eee ee 7 Setup 1 Connect the video signal cables 7 Setup 2 Connect the audio cord 8 Setup 3 Connect the power cord 8 Setup 4 Bundle the cords and cables 9 Setup 5 Turn on the monitor and computer 9 Setup 6 Adjust the tilt and swivel 10 Selecting the input signal INPUT button 11 Customizing Your Monitor 12 Navigating the menu 12 amp PICTURE AUDIO menu 18 MODE MENU oso accade da oe e rd DRE UR ee dol and 13 PICTURE menu S s a kk
7. NTRAST O Adjust the picture contrast 1280x1024 60Hz 1 Press the MENU button Th i th i 4 Press the 4 4 button to select the desired mode and A O o o a D ae E 2 Press the 4 button to select PICTURE eG von AUDIO and press the OK button EE P ee The PICTURE AUDIO menu appears on the screen MOVIE Clear picture with strong contrast e PC Soft tone picture 3 Press the buttons to select 2 PICTURE and AUTO Automatically adjusts the screen brightness press the OK button according to the brightness of the surroundings The PICTURE menu appears on the screen automatic brightness adjustment function For e nre e cA B 4 Press the amp f buttons to select 9 CONTRAST and adjustment function light sensor page 20 press the OK button The CONTRAST menu appears on the screen NOTE In the AUTO mode you cannot adjust the backlight 5 Press the 4 4 buttons to adjust the contrast and press the OK button continued 13
8. SONY TFT LCD Color Computer Display SDM HX73 SDM HX93 2003 Sony Corporation Owner s Record The model and serial numbers are located at the rear of the unit Record these numbers in the spaces provided below Refer to them whenever you call upon your dealer regarding this product Model No Serial No To prevent fire or shock hazard do not expose the unit to rain or moisture Dangerously high voltages are present inside the unit Do not open the cabinet Refer servicing to qualified personnel only FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment in
9. analog RGB for INPUT2 page 7 This connector inputs analog RGB video signals 0 700 Vp p positive and sync signals Audio input jack for INPUT3 page 8 This jack inputs audio signals when connected to the audio output jack of a computer or other audio equipment connected to INPUT3 DVI D input connector digital RGB for INPUT3 page 7 This connector inputs digital RGB video signals that comply with DVI Rev 1 0 Cable holder page 9 This part secures cables and cords to the monitor EE Connect a computer eguipped with a DVI output Setup connector digital RGB Using the supplied DVI D video signal cable digital RGB connect the Before using your monitor check that the following items are computer to the monitor s DVI D input connector digital RGB for included in your carton INPUTS LCD display Power cord e HD15 HD15 video signal cable analog RGB DVI D video signal cable digital RGB Audio cord stereo miniplug CD ROM utlity software for Windows Macintosh Operating Instructions etc Warranty card Quick Setup Guide to the DVI D input connector digital Setup 1 Connect the video signal cables to the computer s DVI output connector digital RGB Turn off the monitor and computer before connecting j them When connecting the computer to the monitor s HD15 i DVI D video signal input connector analog RGB refer to C
10. e adjustments and also display the Volume menu to control the volume 6 OK button page 12 This button activates the selected menu item and adjustments made using the V buttons 5 INPUT button page 11 This button switches the video input signal between INPUTI LI INPUT2 and INPUTS when two computers are connected to the monitor 2 button page 20 This button changes the MODE PICTURE AUDIO 9 Back cover page 7 Slide up this cover when you connect cables or cords Headphones jack page 19 This jack outputs audio signals to the headphones continued 5 Rear of the LCD display INPUT 1 INPUT 2 INPUT 3 11 AC IN connector page 8 This connector connects the power cord supplied Security Lock Hole The security lock hole should be used with the Kensington Micro Saver Security System Micro Saver Security System is a trademark of Kensington Audio input jack for INPUT1 page 8 This jack inputs audio signals when connected to the audio output jack of a computer or other audio equipment connected to INPUTI HD15 input connector analog RGB for INPUT1 page 7 This connector inputs analog RGB video signals 0 700 Vp p positive and sync signals 15 Audio input jack for INPUT2 page 8 This jack inputs audio signals when connected to the audio output jack of a computer or other audio equipment connected to INPUT2 HD15 input connector
11. e audio cord Connect the supplied audio cord to the monitor s corresponding audio input jack Using the monitor s speakers or headphones you can listen to sound from your computer or other audio equipment connected to the monitor s audio input jacks For more information see Controlling the volume on page 19 to the audio input to audio output of the computer or other audio equipment lt audio cord supplied Setup 3 Connect the power cord 1 Connect the supplied power cord securely to the monitor s AC IN connector 2 Connect the other end securely to a power outlet to power outlet 2 power cord supplied Setup 4 Bundle the cords and Setup 5 Turn on the monitor and cables computer 1 Slide up the back cover 1 Press the power switch on the front of the monitor 2 Secure the video signal cable audio cords and the The D power indicator lights up in green power cord using the cable holder on the cabinet 3 Slide down the back cover lights in green back cover 2 Turn on the computer 3 Press the INPUT button to select the desired input signal The selected input s picture appears on the screen For more information see Selecting the input signal INPUT GB button on page 11 INPUT
12. e sure to keep magnetic recording equipment tapes and floppy discs away from the speaker s opening as the speakers generate a magnetic field This magnetic field may affect data stored on magnetic tapes and discs Note on the LCD Liquid Crystal Display Please note that the LCD screen is made with high precision technology However black points or bright points of light red blue or green may appear constantly on the LCD screen and irregular colored stripes or brightness may appear on the LCD screen This is not malfunction Effective dots more than 99 99 Maintenance Besure to unplug the power cord from the power outlet before cleaning your monitor Clean the LCD screen with a soft cloth If you use a glass cleaning liquid do not use any type of cleaner containing an anti static solution or similar additive as this may scratch the LCD screen s coating Clean the cabinet panel and controls with a soft cloth lightly moistened with a mild detergent solution Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzine Do not rub touch or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver This type of contact may result in a scratched picture tube Note that material deterioration or LCD screen coating degradation may occur if the monitor is exposed to volatile solvents such as insecticide or if prolonged contact is maintained with
13. onnect a cable digital RGB computer equipped with an HD15 output connector supplied analog RGB Connect a computer equipped with an HD15 GB n Note Do not touch the pins of the video signal cable connector as this might output connector analog RG B bend the pins Using the supplied HD15 HD15 video signal cable analog RGB connect the computer to the monitor s HD 15 input connector analog RGB for INPUTI or INPUT2 Slide up the back cover Connect the computer according to the following illustrations M Connecting to an IBM PC AT or compatible computer to the HD 15 input connector analog RGB to the computer s HD15 output connector analog RGB 11 U HD15 HD15 video signal cable analog RGB IBM PC AT or compatible supplied computer continued 7 M Connecting to a Macintosh to the HD 15 input connector analog 4 to the computer s output connector DB 11 O qum 0000 00g O O O HD15 HD15 video signal cable analog RGB supplied 000906 TO 00009 O O 001000 Od o O O O O Macintosh When connecting a Macintosh computer use an adapter not supplied if necessary Connect the adapter to the computer before connecting the video signal cable Setup 2 Connect th
14. ple near a radiator heating vent or in direct sunlight Subjecting the monitor to extreme temperatures such as in an automobile parked in direct sunlight or near a heating vent could cause deformations of the casing or malfunctions n places subject to mechanical vibration or shock Near any equipment that generates a strong magnetic field such as a TV or various other household appliances nplaces subject to inordinate amounts of dust dirt or sand for example near an open window or an outdoor exit If setting up temporarily in an outdoor environment be sure to take adequate precautions against airborne dust and dirt Otherwise irreparable malfunctions could occur Handling the LCD screen Do not leave the LCD screen facing the sun as it can damage the LCD screen Take care when you place the monitor by a window e Do not push on or scratch the LCD screen Do not place a heavy object on the LCD screen This may cause the screen to lose uniformity or cause LCD panel malfunctions f the monitor is used in a cold place a residual image may appear on the screen This is not a malfunction The screen returns to normal as the temperature rises to a normal operating level e If a still picture is displayed for a long time a residual image may appear for a while The residual image will eventually disappear The LCD panel becomes warm during operation This is not a malfunction About the built in stereo speakers B
15. rubber or vinyl materials Transportation Disconnect all cables from the monitor and grasp both side of the LCD display firmly taking care not to scratch the screen when transporting If you drop the monitor you may be injured or the monitor may be damaged When you transport this monitor for repair or shipment use the original carton and packing materials Disposal of the monitor Do not dispose of this monitor with general household waste e The fluorescent tube used in this monitor contains mercury Disposal of this monitor must be carried out in accordance to the regulations of your local sanitation authority Identifying parts and controls See the pages in parentheses for further details Front of the LCD display 1 Power switch and power indicator pages 9 19 24 To turn the display on or off press the D power switch The power indicator lights up in green when the display is turned on and lights up in orange when the display is in the power saving mode 2 Light sensor page 20 This sensor measures the brightness of the surrounding area Be sure not to cover the sensor with papers etc Stereo speakers page 19 These speakers output the audio signals as sound 4 MENU button page 12 This button turns the menu screen on and off V t and volume control buttons pages 12 19 These buttons are used to select the menu items and mak
16. tments Connect the monitor and the computer and turn them on For the best results wait for at least 30 minutes before making adjustments You can make numerous adjustments to your monitor using the on screen menu Navigating the menu 1 Display the main menu Press the MENU button to display the main menu on your screen MENU 3 M gt 3 a gt lt 1280x1024 60Hz 2 Select the menu Press the buttons to display the desired menu Press the OK button to move to the first menu item m OK P 28S 7 A sz 3 Select the item you want to adjust Press the 4 buttons to select the item you want to adjust then press the OK button 48 OK P l a5 7 A S If S is one of the menu items When you select and press the OK button the display returns to the previous menu 12 4 Adjustthe item Press the V f buttons to make the adjustment then press the OK button When vou press the OK button the setting 1s stored then the display returns to the previous menu OK 5 Close the menu Press the MENU button once to return to normal viewing If no buttons are pressed the menu closes automatically after about 45 seconds MENU M Resetting the adjustments to the default settings You can reset the adjustments using RESET menu For more information about resetting the adjustments see gt lt RESET on page 18 B PICTURE menu 2 You can adjust the following items using the PICTURE menu e BACKLIG
17. to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment IMPORTANTE Para prevenir cualquier mal funcionamiento y evitar da os por favor lea detalladamente este manual de instrucciones antes de conectar y operar este equipo If you have any questions about this product you may call Sony Customer Information Center 1 800 222 SONY 7669 or write to Sony Customer Information Center 1 Sony Drive Mail Drop T1 11 Park Ridge NJ 07656 Declaration of Conformity Trade Name SONY Model No SDM HX73 HX93 Responsible Party Sony Electronics Inc Address 680 Kinderkamack Road Oradell NJ 07649 USA Telephone No 201 930 6972 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTICE This notice is applicable for USA Canada only If shipped to USA Canada install only a UL LISTED CSA LABELLED power supply cord meeting the following specifications SPECIFICATIONS Plug Type Nema Plug 5 15p Cord Type SVT or SJT minimum 3 x 18 AWG Length Maximum 15 feet Rating
Download Pdf Manuals
Related Search