Home
JVC HR-S9911 S
Contents
1. is displayed on the display panel 24HR Quick Programing You can program a timer recording that starts within 24 hours using the ADVANCED JOG dial on the VCR Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically El Press 24HR QUICK PROGRAM on the y VCR P starts blinking on the ys display panel PA Turn the ADVANCED JOG dial to the starttime 7 left or right to set the start time Yang e One click stop of the ADVANCED JOG dial changes the time in 5 minute intervals Push the ADVANCED JOG dial gt I starts blinking on the display panel Turn the ADVANCED JOG dial to the left or right to set the stop time e To set the tape speed press SP EP ZIM El Push the ADVANCED JOG dial Turn the ADVANCED JOG dial to the left or right to select the channel then press 24HR QUICK PROGRAM The VCR turns off automatically and is displayed on the display panel PROGRAM 1 START STOP 8 00AM 9 00AM D ATE CH 12 24 02 EN Ni TUE DBS PRESS SP EP 8 DAILY 9 WEEKLY 7 DBS THEN 0K PRESS PROG TO END NOTES f Err appears on the display panel repeat the above steps again e When a menu screen is shown you cannot use 24HR Quick Programing function Press MENU to return to normal screen and try again You can use 24HR Quick Programing function also when the VCR is turned off e For 24HR Quick Pro
2. ON OFF When this function is set to ON edge correction to the luminance signal is performed to enhance details Normally set this function to ON NOTES e Depending on the type of tape being used picture quality may be better with DIGITAL R3 set to OFF f you use this VCR as the playback VCR for editing be sure to set DIGITAL R3 to OFF before starting Hi VIDEO STABILIZER ON OFF When this function is set to ON you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR NOTES e Jo watch recordings with close caption or when you finish viewing a tape set this function to OFF Video Stabilizer and Digital TBC NR pg 12 cannot be used at the same time If you activate Digital TBC NR when VIDEO STABILIZER is set to ON VIDEO STABILIZER will be automatically set to OFF W BLUE BACK ON OFF When this function is set to ON the TV screen becomes all blue when receiving a channel not in use NOTE When you want to receive an unstable channel with poor signals set this function to OFF HI 2ND AUDIO RECORD ON OFF e When this function is set to ON If a SAP program is received the SAP audio is recorded on both the normal and Hi Fi tracks The main audio is not recorded If a non SAP program is received the main audio is recorded on both the Hi
3. e When playing back an audio dubbed tape press AMONITOR to select the soundtrack you wish to hear pg 11 Selecting monitor sound Insert Editing and AV Dubbing Insert Editing You can replace a recorded scene with new scene recorded on another tape or with other material Both the picture and the sound recorded on the Hi Fi sound track are replaced at the same time AV Dubbing You can perform Audio Dubbing and Insert Editing at the same time This means that the picture and the sounds recorded on the Hi Fi sound track and on the normal track are replaced at the same time e For AV Dubbing you can edit pictures and sound using different sources connect a video source to the video input connector and an audio source to the audio input connectors EE Make connections Connect the supplied audio video cable between the VCR s audio video input connectors and the other component s audio video output connectors Insert Editing and AV Dubbing are possible only by using the audio video input connectors on the front panel or on the rear panel This VCR for recording t To S VIDEO input S video cable supplied Audio video cable supplied tL v To audio video output J Another VCR for playback i 1 To S video output FA Select input location Select F 1 when connecting the other component to the audio video input connectors on the front panel Select L 1
4. PROG END PROGRAM 4 DA C 12 24 02 10 SP TUE PRESS CANCEL TO CANCEL PRESS 0K TO CONFIRM PRESS PROG TO END Video Navigation When you record a TV program with this VCR the VCR automatically stores in its memory the recording start time date channel information etc If the tape is recorded on this VCR for the first time new tape number and the recording date are also registered On the tape only the tape number information is recorded e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR Navigation Playback You can quickly find programs you have recorded on a tape using this VCR You can also select a program to watch and then automatically search for the beginning of the program EE Load a cassette Inserting the cassette recorded on this VCR e The VCR turns on automatically e The tape will run for a few seconds while the VCR searches for the tape number e f the cassette s record safety tab has been removed playback begins automatically FA Access Title screen Press NAVIGATION After pressing NAVIGATION it may take a few seconds to access the Title screen e If there is no cassette loaded the Find Title screen appears C pg 18 EJ Select program then start playback Gaon FOOTBALL 02 Press AV to move the highlight bar 10 OOPM 2 26 01 Bow RO then Hani 11 00PM 2 26 01 CH 16 program you
5. Vo 0502MNV KID KPJ
6. D SKIP SEARCH button PROG Program CHECK button D PLAY button D FF amp amp P button D PAUSE HM button D lt lt gt e lt gt button TV VOL button REVIEW button NAVIGATION button D JOG SHUTTLE button and lamp D SHUTTLE ring Connections and Plug amp Play Setting EE Check contents Make sure the package contains all of the accessories listed in Specifications CF pg 26 VI Situate VCR Place the VCR on a stable horizontal surface Connect VCR to TV Antenna or cable A Coaxial cable Flat feeder Matching transformer not supplied AC power cord Back of VCR AC outlet Audio video cable supplied To audio video input connectors S video cable supplied __ _ Eee 4 TV To S video input connector To 75 Q terminal RF cable supplied RF Connection Disconnect the TV antenna from the TV Connect the TV antenna cable to the ANTENNA IN terminal on the rear of the VCR Connect the supplied RF cable between the TV OUT terminal on the rear of the VCR and the TV s antenna input terminal eo AV Connection improves picture quality during tape playback If your TV is equipped with audio video input connectors Connect the antenna VCR and TV as shown in the illustration Connect the supplied audio video cable between the AUDIO M VIDEO OUT connectors on the rear of the VCR and t
7. s built in MTS decoder enables reception of Multichannel TV Sound broadcast To record a SAP program received set 2ND AUDIO RECORD to ON I pg 20 S VHS Super VHS S VHS ET or VHS Recording Mode This VCR can record in S VHS Super VHS S VHS ET or VHS e To record in S VHS Set S VHS MODE to ON CF pg 20 Then insert a cassette marked S VHS The S VHS indicator lights up on the display panel The S VHS recording mode is selected e To record in S VHS ET on a VHS cassette Set S VHS ET to ON CF pg 19 Then insert a cassette marked VHS The S VHS indicator lights up on the display panel e To record in VHS Insert a cassette marked VHS Set S VHS ET to OFF cF pg 19 e To record in VHS on an S VHS cassette Insert a cassette marked S VHS The S VHS indicator lights up on the display panel Then set S VHS MODE to OFF C pg 20 The S VHS indicator goes off The VHS recording mode is selected NOTE When playing back a tape that has been recorded in S VHS or S VHS ET the S VHS indicator lights up on the display panel regardless of the S VHS ET or S VHS MODE setting c pg 19 20 Retake You can cut out unnecessary parts of a TV program while you are recording it End of program Beginning of program Program Recorded part b Go back to end of program to cut out unnecessary part
8. si VO Reverse Forward Aa ka ka 1 6 1 18 1 18 1 6 1 2 230 7 31 21 7 3 1 6 1 18 1 18 1 6 1 2 2 3 7 21 31 You can see smooth slow motion picture only during 1 2x slow motion playback When the tape is not running Rewind fast forward On the VCR Turn the ADVANCED JOG dial to the left to rewind the tape or right to fast forward the tape On the Remote Press REW 4414 to rewind the tape or FF to fast forward the tape Eject the cassette Press STOP EJECT W amp on the VCR You can also eject the cassette when the VCR is turned off Turn off the VCR Press POWER Playback Features e Turn on the VCR and TV and select the VCR channel or AV mode Set the VCR TV CABLE DBS selector on the Remote to VCR Adjusting tracking condition Tracking Adjustment Automatic tracking adjustment Whenever you insert a tape and start playback automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback Manual tracking adjustment If automatic tracking cannot eliminate noises well during playback follow the procedures below E Press CH and on the VCR simultaneously during playback to activate manual tracking PA Press CH or to eliminate the noises Press it briefly for a fine adjustment or press and hold for a coarse adjustment Press CH and simultaneously again to reactivate automatic tracking
9. the recording stops and D and 00 on the display panel blink Press TIMER to disengage timer then press STOP EJECT amp on the VCR to eject the cassette or press POWER then press REW 44 on the Remote or turn the ADVANCED JOG dial to the left on the VCR to rewind the tape e If MEMORY FULL appears on the TV screen when you finish a program setting the VCR s memory for the Video Navigation function is full This is not related to actual recording but the program information will not be stored in the VCRS memory pg 16 Video Navigation Changing VCR Plus Setting The VCR Plus programing system assigns a VCR Plus guide channel to the TV channels and the cable channels These guide channel numbers are also called the VCR Plus channel codes TV listings often have a section in chart form indicating the guide channel number assigned to each station To ensure that VCR Plus timer recording operates correctly it is necessary to set the VCR Plus Guide Channel Set for each station If you have moved to a different area or if a broadcasting station s channel number has been changed perform the following steps to set the correct guide channel and corresponding VCR channel number EE Access Main Menu screen then Initial Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt Pl Access Guide Channel Set screen Pr
10. when connecting the other component to the audio video input connectors on the rear panel On the VCR Press CH or push the ADVANCED JOG dial then turn it to the left or right until L 1 or F 1 appears on the display panel On the Remote Press AUX and or CH until L 1 or F 1 appears on the display panel EJ Select video input connector Select the appropriate mode depending on the connector being used pg 21 When using S VIDEO input connector on the front panel set FRONT AUX INPUT to S VIDEO When using S VIDEO IN connector on the rear panel set REAR AUX INPUT to S VIDEO When using VIDEO input connector on the front panel set FRONT AUX INPUT to VIDEO When using VIDEO IN connector on the rear panel set REAR AUX INPUT to VIDEO Pl Select edit mode Set the edit mode to ON for the VCRs if such a mode is equipped e On this VCR set PICTURE CONTROL to EDIT pg 20 CONTINUED ON NEXT PAGE E Locate end point Load the cassette to be edited into the VCR and press PLAY Press PAUSE IB when you find the end of the scene that you want to edit Press C RESET so that the counter reading becomes 0 00 00 You can also use FF gt the ADVANCED JOG dial on the VCR or the JOG dial SHUTTLE ring on the Remote to locate the end point EJ Locate start point and engage Insert Editing mode Use REW 444
11. 12 10 00A 10 45 40 11 30P 1 00 125 P 1 2 3 4 5 6 7 8 PRESS CHECK TO NEXT a Program overlap warning display If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears you have another program overlapping the program you have just made The Program Check screen appears and conflicting programs will start blinking PR START STOP CH DATE 1 8 00P 10 00 12 12 24 PROGRAM NOT COMPLETED PROGRAM OVERLAP 2 10 00A 10 45 40 3 11 30P 1 00 125 4 9 00P 10 00 10 12 24 5 6 7 8 4 7 THEN p PROG END Example Program 1 you have just made and Program 4 overlap each other Kl Select program to modify Press AV then press OK or gt You can only select one of the overlapping programs e If you do not mind this overlap press PROG to finish the timer program setting The program starting earlier or program with the lower program number will be recorded PI Cancel or change program setting To cancel a program press CANCEL when SUN es See the Program screen you do not want is ATE H shown To change a program press the appropriate button START STOP DATE CH DAILY M F Number key 8 WEEKLY Number key 9 and or SP EP 4 47 when the Program screen on which you want to make changes is shown then press OK or b e If the overlap is not yet solved the conflicting programs will be shown on the Program check screen Repeat the above steps again 4 v THEN pi
12. C See above REAR AUX INPUT PA Set timer program on DBS receiver using its instruction manual E Load a cassette with the record safety tab intact El Press SP EP to set the tape speed The selected tape speed will appear on the TV screen El Press REC LINK for more than 2 seconds The VCR turns off automatically and enters the Satellite Auto Recording standby mode and the REC LINK lamp lights When the DBS receiver outputs a signal the VCR starts recording and the REC LINK lamp blinks The VCR stops recording and powers off when the DBS receiver stops outputting a signal NOTES e Be sure not to turn on the DBS receiver before the program starts broadcasting otherwise the VCR will start recording when the DBS receiver is turned on e To disengage the Satellite Auto Recording standby mode press REC LINK the REC LINK lamp goes off e Depending on the type of DBS receiver Satellite Auto Recording may not be compatible Child Lock e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR You can disable the VCR operations While the VCR is turned on press and hold POWER on the Remote for more than 10 seconds The VCR turns off CL appears for about 5 seconds on the display panel To release the child lock press and hold POWER on the Remote until the VCR turns on NOTES e Pressing TIMER during timer record
13. Echostar Communications Corporation For Customer Use Enter below the Model No and Serial No which are located on the rear of cabinet Retain this information for future reference Model No Serial No SVHS Cassettes marked S VHS and VHS can be used with this video cassette recorder However S VHS recordings are possible only with cassettes marked S VHS By using S VHS ET it is possible to record and play back with S VHS picture quality on VHS cassettes with this VCR IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful functions But improper use can result in potential electrical shock or fire hazards This product has been engineered and manufactured to assure your personal safety In order not to defeat the built in safeguards observe the following basic rules for its installation use and servicing ATTENTION Follow and obey all warnings and instructions marked on your product and its operating instructions For your safety please read all the safety and operating instructions before you operate this product and keep this booklet for future reference INSTALLATION 1 Grounding or Polarization A Your product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet
14. Fi and normal tracks e When this function is set to OFF the SAP audio cannot be recorded NOTE When the channel is changed on the VCR e The STEREO indication appears on the screen for about 5 seconds if the program is a stereo broadcast The SAP indication appears on the screen for about 5 seconds if the program is a SAP broadcast e Both indications appear when a stereo program is accompanied by SAP sound Hi AUDIO MONITOR HI FI HI FI L HI Fl R NORM MIX This VCR can record two sound tracks simultaneously normal and Hi Fi on a Hi Fi stereo tape You can select the sound track s to listen to while playing back a Hi Fi stereo tape In addition when playing back a prerecorded tape containing two separate audio programs on the Hi Fi tracks you can choose either one by selecting either HI FI L or HI FI R HI FI Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back MIX Both sounds on the Hi Fi track and normal track are mixed and played back NOTES e While playing back a monaural tape sounds on the normal track will be heard regardless of this setting e If RF connection t pg 6 is used for viewing pictures on the TV sound will be monaural even though you select HI FI You can also use the AAMONITOR button on the R
15. MENU TO END 16 _it is impossible to restore that information Screens for video Screens for video navigation close after about 60 seconds if no operation is performed LA LI e Editing Titles You can edit the tape title and the program titles as you like You can also edit the category in the program title In short you can use the Video Navigation function to create your own video tape library Preparations MAIN MENU EE Access Main Menu screen then Video FUNCTION SET Navigation screen FUNG TION Press MENU on the Remote Press AV to IMALSET move the highlight bar arrow to VIDEO NAVIGATION then press OK or Ps PRESS a v THEN OK PRESS MENU TO END VI Access Edit Title screen Press AV to move the highlight bar arrow to EDIT TITLE then press OK or es VIDEO NAVIGATION EDIT TITLE FIND TITLE FIND BLANK SPACE CHECK MEMORY NAVIGATION ON SELECT WITH a v AND OK PRESS MENU TO END EJ Select tape number 5a 171 Sake 0115 _ MOVIE Press AV to move the highlight bar arrow to the tape number for which you lt 0112 2 23 02 want to edit then press OK or gt Dilo BASEBALL e indicates the tape currently inserted D106 i BESTT in the VCR PRESS a v THEN OK PRESS MENU TO END Editing tape title First follow steps fl to E in Preparations above then go to the following steps E Select tape title Press AV to move the highlight bar arrow to the
16. OFF you can use this terminal as the REMOTE PAUSE terminal If your JVC camcorder is equipped with the Master Edit Control you can control the VCR from the camcorder Connect the mini plug cable not supplied with this VCR between the REMOTE PAUSE terminal and the EDIT connector on the camcorder NOTE Refer to the other components instruction manuals for connection and its operations Hi FRONT AUX INPUT VIDEO S VIDEO You have to select which terminal either VIDEO composite or S VIDEO Y C separate signals to use as the video input terminal on the front panel Make sure to select the correct terminal otherwise you may fail in recording editing on this VCR Mi REAR AUX INPUT VIDEO S VIDEO You have to select which terminal either VIDEO composite or S VIDEO Y C separate signals to use as the video input terminal on the rear panel Make sure you select the correct terminal otherwise you may fail in recording editing on this VCR Satellite Auto Recording You can automatically record a satellite program which is timer programed on your DBS receiver e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR El Connect a DBS receiver to the AUDIO VIDEO IN or S VIDEO IN connectors on the rear panel You can also connect the cable box if it has a timer To use these connectors you have to select which one to use
17. OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CAUTION This video cassette recorder should be used with AC 120V U 60Hz only To prevent electric shocks and fire hazards DO NOT use any other power source CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical CAUTION Changes or mod
18. Selecting monitor sound Audio Monitor While playing back a tape on which stereo sound or SAP sound is recorded press AAMONITOR on the Remote Each time you press the button sound changes HI FI Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back NORM HI FI Both sounds on the Hi Fi track and normal track are mixed and played back NOTES e The above indication appears when SUPERIMPOSE is set to ON pg 20 though the monitor sound changes in sequence You can also use the menu AUDIO MONITOR to select your desired monitor sound pg 20 Automatic operations after rewinding Next Function Memory The Next Function Memory tells the VCR what to do after rewinding is complete Ensure that the VCR is in stop mode e For Automatic Playback Start Press REW lt lt then press PLAY gt within 2 seconds e For Automatic Power Off Press REW lt lt then press POWER within 2 seconds e For Automatic Timer Standby Press REW lt lt then press TIMER within 2 seconds NOTE It is not possible to select the Automatic Timer Standby function if the cassette s record safety tab is removed Playing back tape repeatedly 100 times Repeat Play During playback press and hold PLAY B gt for more t
19. audio component to the audio input connectors on the rear panel On the VCR Press CH or push the ADVANCED JOG dial then turn it to the left or right until L 1 or F 1 appears on the display panel On the Remote Press AUX and or CH until L 1 or F 1 appears on the display panel EJ Locate start point and engage Audio Dubbing mode Load a cassette and press PLAY b on the VCR Press PAUSE II at the point where you want to start dubbing then press A DUB e The VCR enters the Audio Dubbing Pause mode blinks El Start dubbing Engage the Play mode on the audio component then press PLAY on the VCR Audio Dubbing begins 2 blinks and lights up on the display panel e To pause dubbing press PAUSE I Press PLAY to resume dubbing E End Audio Dubbing Press STOP W on the Remote or STOP EJECT i 4 on the VCR then engage the Stop mode of the audio component NOTES e When monitoring the sound during Audio Dubbing the normal soundtrack is automatically selected If you wish to hear the Hi Fi or mixed sound Hi Fi normal soundtracks press A MONITOR to select NORM HI FI pg 11 Selecting monitor sound e Audio Dubbing stops automatically when the counter reaches 0 00 00 and the VCR enters the Play mode Check the counter reading before dubbing e Audio Dubbing is not possible with a cassette whose record safety tab has been removed
20. automatically set to OFF Make sure Digital TBC NR is deactivated when you want to use Video Stabilizer Recording It may be unlawful to record or play back copyrighted material without the consent of the copyright owner Accidental erasure prevention To prevent accidental recording on a recorded cassette remove its record lt lt safety tab To record on it later cover N Record safety tab the hole with adhesive tape Basic Recording e Turn on the VCR and TV and select the VCR channel or AV mode Set the VCR TV CABLE DBS selector on the Remote to VCR When you record the programs on this VCR the tapes are automatically numberd so that every tape recorded on this VCR has a different tape number if NAVIGATION is set to ON CF pg 16 The program information such as recording date start time channel number and recording speed are also automatically stored in the VCR s memory For details refer to Video Navigation I pg 16 EE Load a cassette Make sure the record safety tab is intact If not cover the hole with adhesive tape before inserting the cassette e The VCR turns on automatically e The tape will run for a few seconds while the VCR searches for the tape number FA Select recording channel On the VCR Press CH Or push the ADVANCED JOG dial then turn it to the left or right On the Remote Press CH or the Number keys e If you connect the
21. information ss sas saa aa ea a a asii 19 Function setings asrine ag aaa a aa d a ga E NA A ga aa aa 19 Satellite Auto RECOMGING soren aa aia Pang kaa aaa Da kii nda gaga 21 CHIT Bole aga pena te ajah ne a a aaa aa a aa aapa aa aaa 2A JERARD INT NET Saline sasaran D aaa a Pa aa Daane 21 Multi Brand Remote Control sasasi aaa AN AA NAGA NANA AA a 22 Changing Remote Control Code cectechevadevess andes seas 22 Editing RE Oe a POPES NS a an ar 23 Editing Ot Camcorder sasa aaa aa anae ngang aaa a Dak ka agan aa Na aaa 23 Editing with Another VER asasi ana aka da a aa aa ena pal sa anaa pad kaa 24 AGUO DUODENO reoaine et na TA Anak kana Aa a Aa Da galan ah 25 Insert Editing and AV Dubbing caisson eect sap igeatermeas 25 Specifica ONS sisa wan danda nan DAN anana naka an ae Saad aatia aas 26 Troobles hooting asas sana NGE caps an Daka NG aka daa aana andapan 27 FOR SERVICING Only in U S A ccccsccccscssesesessssesecessscesecesees 29 WARRANTY Only in U S A scccscscscssscssscesssscssssssesceseseceseses 30 VIDEO CASSETTE RECORDER HR S9911U SVHS iieii eng t Super VHS ET INSTRUCTIONS Dear Customer Thank you for purchasing the JVC S VHS video cassette recorder Before use please read the safety information and precautions to ensure safe use of your new VCR CAUTIONS IN CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
22. kind on the product 5 Attachments Do not use attachments not recommended by the manufacturer of this product as they may cause hazards 6 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 7 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANSI NFPA 70 DISCHARGE UNIT NEC SECTION ELECTRIC SERVICE 810 20 EQUIPMENT CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE PORTABLE CART WARNING Symbol provided by RETAC SERVICING 1 Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 2 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or
23. nearest JVC Factory Service Center the name and location of which will be given to you by the toll free number If you have any questions concerning your JVC Product please contact our Customer Relations Department WHAT IS NOT COVERED This limited warranty provided by JVC does not cover 1 Products which have been subject to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service or if affixed to any attachment not provided with the products or if the model or serial number has been altered tampered with defaced or removed Initial installation and installation and removal for repair Operational adjustments covered in the Owners Manual normal maintenance video and audio head cleaning Damage that occurs in shipment due to act of God and cosmetic damage Signal reception problems and failures due to line power surge Video Pick up Tubes CCD Image Sensor Cartridge Stylus Needle are covered for 90 days from the date of purchase Accessories Batteries except that Rechargeable Batteries are covered for 90 days from the date of purchase COON OD O1 B ON There are no other express warranties except as listed above THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EX
24. o I a PROG SKIP SEAI CHECK gt I oe aa hee KIDAN When you use the JOG dial SHUTTLE ring on the Remote first press JOG SHUTTLE so that the button lights up VCR operation mode Tape speed Cassette mark 0 Tape position Index number QO Tape remaining time Time counter Audio monitor indications SAP indication STEREO program indication Day and clock time Channel and auxiliary input L 1 and F 1 Timer warning display To recall an indication 1 Press OSD or OK All indications corresponding to the current status are displayed for 5 seconds After that the counter information and RECORD PAUSE if in the Record Pause mode remain on the TV screen 2 Press OSD or OK again to clear the display e The RECORD PAUSE indication remains on the TV screen VCR TV CABLE DBS selector TV VCR button A B button Number keys Character input buttons DBS button CANCEL button C Counter RESET button STOP button START button PROG Program button O SP EP ZIM button D REW lt lt amp button REC button STOP button A V buttons TV CH buttons MENU button OK button D JOG dial A Audio MONITOR button m s TV Muting button D POWER button d DISPLAY button ENTER button OSD button D DAILY M F button D WEEKLY button AUX button TIMER button D DATE button CH button
25. or gt TUNER SET BAND AUTO CHANNEL SET MANUAL CHANNEL SET SELECT WITH 4 AND OK PRESS MENU TO END EJ Add or skip desired channels To add channels 1 Press the Number keys on the Remote to input a channel number you want to MANUAL CHANNEL SET eur CH 45 ADD 4 gt add PRESS NUMBER KEY 0 9 OR 4 THEN OK Press OK or gt to set to ADD PRESS MENU TO END eo n gt Repeat 1 to 2 to add other channels Press MENU to return to normal screen To skip channels Press AV or the Number keys to select a channel number you want to skip Press OK or gt to set to SKIP Repeat 1 and 2 to skip other channels Press MENU to return to normal screen eo rn After a power failure occurs band selection will be reset to CATV Cable Box and or DBS Receiver Control Setting The following procedure is required if you receive your TV channels through a cable box descrambler and or if you receive satellite channels through DBS Direct Broadcast Satellite receiver The supplied Controller allows the VCR to automatically switch the cable box or DBS receiver s channel during timer recording NOTES e For the cable box the Controller is effective for VCR Plus system or Express timer programing For the DBS receiver the Controller is effective only for Express timer programing e When connecting y
26. or enter a PBS channel number Press OK or gt to move the highlight bar to HOST CH then press AV repeatedly until AUTO or the desired PBS channel number is selected e Some PBS channels do not transmit clock setting data EJ Select D S T mode Press OK or gt to move the highlight bar to D S T then press AV repeatedly until the desired setting is selected AUTO Select if you want to adjust your VCR s clock automatically by the incoming signal from the host channel Auto Daylight Saving Time enables automatic adjustment of the VCR s clock at the start and end of Daylight Saving Time Be sure to select the correct time zone manually in step B ON Adjustment will be made by the built in clock itself OFF Select when Daylight Saving Time does not apply to you E Select time zone Press OK or gt to move the highlight bar to TIME ZONE then press AV repeatedly until AUTO or the desired time zone is selected Each time you press the button the time zone changes as follows lt gt AUTO gt ATLANTIC gt EASTERN gt CENTRAL lt gt MOUNTAIN gt PACIFIC lt gt ALASKA gt HAWAII lt gt back to the beginning E Complete Semiauto Clock Set Press MENU to return to normal screen Turn off the VCR Auto will appear on the display panel while the clock is being set The current clock time will appear automatically when the clock setting is complete Selections of
27. pg 22 Playback SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION The tape is running but the If the RF connection I pg 6 is used to view the J Select channel 3 or 4 on the TV picture will not appear picture the channel on the TV is set incorrectly e If the AV or S video connection CF pg 6 is used f Select the AV mode on the TV to view the picture the TV receiver is set to the wrong mode Recording SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Recording will not start e There is no cassette loaded e Insert a cassette on which the record safety tab is intact e The loaded cassette has had its record safety tab Remove the cassette and cover the hole with removed adhesive tape or load a cassette on which the record safety tab is intact Timer Recording SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Timer recording will not e The clock and or the timer program have been set f Set the clock and or timer program correctly work incorrectly e The timer is not engaged Press TIMER to engage the timer and make sure that appears on the display panel e The VCR has not been set up properly e Re perform the set up procedures Make sure you have compensated for guide channel and VCR or cable box channel number mismatches gt pg 14 Timer programing will not f Timer recording is in progress e Timer programing cannot be performed when work timer recording is in progress Wait until it finishes
28. power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal USE 1 Accessories To avoid personal injury e Do not place this product on an unstable cart stand tripod bracket or table It may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Use a mounting accessory recommended by the manufacturer and follow the manufacturer s instructions for any mounting of the product e Do not try to roll a cart with small casters across thresholds or deep pile carpets 2 Product and Cart Combination A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 3 Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 4 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any
29. program then press OK e The calculated blank space is based on the current tape speed SP or EP selected PAGE lt p on the VCR e If the selected cassette has already been loaded the VCR searches the beginning of the blank space and goes into the stop mode automatically E1 Load cassette Insert the tape of the selected number e The VCR searches the beginning of the blank space and goes into the stop mode automatically PRESS a W THEN OK TO SEARCH END MENU INSERT TAPE 0998 PRESS MENU TO END f Other Functions Timer warning display A warning appears on the TV screen to tell you that the timer recording is to start in 5 minutes if you are not in the timer recording standby mode at that time Press TIMER to put the VCR into timer recording standby mode To clear the display press CANCEL on the Remote WARNING TIMER RECORDING TO START SOON CANCEL Checking tape position When you change the VCR operation mode from the stop mode to fast forward or rewind mode or when you perform an Index Search pg 11 or Instant Review REMAIN 1 00 pg 12 the tape position indicator a appears The position of W in relation to B Beginning or E End shows you where you are on the tape e Set SUPERIMPOSE to ON pg 20 B JF E Changing display information Each time you press DISPLAY the display panel shows the time counter the c
30. tape title then press OK or 50 0114 3 18 02 1 3 8 00PM 2 27 02 CH 5 10 00PM 2 28 02 CH 16 8 15AM 1 15 02 CH 99 PRESS a v THEN 0K TO EDIT OR CANCEL TO DELETE PRESS MENU TO END FA Enter tape title Press the appropriate Number keys on the Remote to enter the title then press OK For details refer to How to enter the characters below Press MENU to return to normal screen How to enter the characters Press the appropriate Number key then press gt to enter each character oe ee ABC2AAAAAAC DEF3EEEE A GHI14 JKL5 Number Key O _ space NOTES e If you make a mistake press lt gt to select the character then enter the correct character If you want to delete a character press lt gt to select the character then press CANCEL Editing program title and category First follow steps fl to Ml in Preparations above then go to the following steps Kl Select program Press AV to move the highlight bar arrow to the program you want to edit then press OK or gt TUE Mea PRESS a v THEN FA Enter program title OK TO EDIT OR CANCEL TO DELETE l PRESS MENU TO END Press the appropriate Number keys on the Remote to enter the title then press OK For details refer to How to enter the characters in the left column E Select category Press AV to select the category you want then press OK or gt e Each time you press AV ca
31. the ADVANCED JOG dial on the VCR or the JOG dial SHUTTLE ring on the Remote to rewind the tape Press PAUSE IB when you find the beginning of the scene for which you want to edit then press INSERT e The VCR enters the Insert Editing Pause mode 2 and light up on the display panel e If you want to perform AV Dubbing and replace the picture Hi Fi audio soundtrack and normal audio soundtrack all at the same time after you press INSERT press A DUB also 2 and Start editing Load the source cassette and engage the Play mode of the other component then press PLAY on the VCR Insert Editing begins 2 and light up on the display panel e Insert Editing stops automatically when the counter reaches 0 00 00 and the VCR enters the Play mode To stop editing any time during recording Press STOP W on the Remote or STOP EJECT Mi 4 on the VCR then engage the Stop mode of the other component Press REC on the recording VCR NOTES Be sure to select AUTO for PICTURE CONTROL or NORM when VIDEO CALIBRATION is set to OFF after you finish editing pg 20 e Editing is not possible with a cassette whose record safety tab has been removed e The recording speed SP EP is determined by the previous recording to be replaced If the recording speed changes on the tape to be edited while editing the tape the inserted picture will be distorted
32. then press OK or INITIAL SET CLOCK SET LANGUAGE ENGLISH AAMT CHANNEL SET DBS RECEIVER SET gt JLIP ID NO SET SELECT WITH 4 AND OK PRESS MENU TO END kl Set JLIP ID number Press the appropriate Number keys on the Remote to enter the desired ID number then press OK Press MENU to return to normal screen JLIP ID NO SET PRESS NUMBER KEY ma THEN OK PRESS MENU TO END Multi Brand Remote Control When programed set with a manufacturer s brand s code this Remote can perform some of the remote control functions of the listed TVs cable boxes and DBS Direct Broadcast Satellite receivers You can control a JVC TV without setting a brand code NOTES e Some unit s brands have more than one code listed If after setting the remote does not operate the unit try one of the other listed codes e Depending on the type of unit some or all functions cannot be operated using this Remote It is impossible to control a unit that does not have a remote sensor tis not possible to set the Remote for both your cable box and a DBS receiver at the same time e Once you have set the Remote to operate a unit you do not have to set it again until you replace the Remote s batteries f the batteries of the Remote are discharged the Remote will not be able to control the TV cable box or DBS receiver Replace the batteries TV Brand Setting e Turn on the VCR and TV and select the VCR chann
33. to access the PlusCode No screen VI Press START once to access PROGRAM 1 Program screen START STOP Press START STOP DATE or CH repeatedly to enter the start time stop time date or channel PRESS SP EP 8 DAILY e Press and hold START or STOP WEEKLY THEN ok to increase the time in 30 minute intervals e To set the tape speed press SP EP e To timer record daily Monday Friday or weekly serials press DAILY M F Number key 8 or WEEKLY Number key 9 Pressing the button again makes the DAILY or WEEKLY display disappear e If you are using a DBS receiver and DBS RECEIVER SET is set to ON the band indication appears under the channel number indication Refer to Cable Box and or DBS Receiver Control Setting pg 8 TV To timer record a regular TV broadcast received on the VCR CATV To timer record a cable TV broadcast received on the VCR or through a cable box unless CABLE BOX SET is set to OFF DBS To timer record a satellite broadcast received through a DBS receiver If the channel number entered requires that the band be set and 7 DBS is displayed on the screen press DBS Number key 7 to select DBS Press OK or PROG e If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears see Program overlap warning display C pg 16 El Press TIMER The VCR turns off automatically and
34. unwanted portions Skip Search Press SKIP SEARCH on the Remote once to 4 times during playback Each press initiates a 30 second period of high speed playback up to 2 minutes When the specified portion of the tape is skipped normal playback resumes automatically To return to normal playback during Skip Search press PLAY PB Adjusting picture condition Digital TBC NR The Digital TBC NR Time Base Corrector Noise Reduction function removes jitter from fluctuating video signals to deliver a stable picture even with old tapes and rental tapes The Digital R3 function 7 pg 20 which cuts noise and reproduces clear pictures is also linked to this function We recommend that you use the Digital TBC NR function when playing back a tape recorded on a camcorder playing back a tape repeatedly used using this VCR as the playback VCR for editing Press DIGITAL TBC NR on the VCR so that the DIGITAL TBC NR lamp lights up Each time you press the button this function turns on and off NOTES f you play back a tape on which certain types of signals using a PC or some character generators have been recorded with Digital TBC NR activated the playback picture may be distorted In this case deactivate Digital TBC NR e Digital TBC NR and Video Stabilizer pg 20 cannot be used at the same time If you activate Digital TBC NR when VIDEO STABILIZER is set to ON VIDEO STABILIZER will be
35. want to play gt 9 00PM 2 26 02 CH 56 back then press OK ital elt e Playback starts automatically after the WORLD CUP 02__ SPORTS l PRESS a THEN OK selected program is located NAVIGATION TC PRESS NAVIGATION TO END Video Navigation Title Screen S0 0013 FOOTBALL 02 1 3 BLANK 1 25 EP 10 oopm 2 26 01 CH123 11 00PM_2 26 01_CH16 8 1 9 00PM_2 26 02_ CH 56 QO lt 8 5AM 1 15 02 CH 99 9 00P 10 30P 1 30 SP 6 WORLD CUP 02 SPORTS PRESS 4 THEN OK PRESS NAVIGATION TO END Tape number Tape title If there is no tape title entered the earliest recording date will be displayed Current page number total page number Largest blank space on the tape Calculated remaining time based on the current tape speed SP or EP selected on the VCR Recorded programs on this tape QO Detailed information of currently selected program Recording start time end time recording length recording speed program title and category If there are no title and category entered TITLE and CATEGORY will be displayed Current tape position is displayed if the currently selected program and the current tape position are different while tape is not running Currently selected program Program information Recording start time date and channel number Deactivating Video Navigation If you do not want to store program information you can deactivate the Video Navig
36. where the recording speed changes When you edit a tape a small portion of the recording preceding to the editing start point will be erased from the edited tape f Specifications GENERAL Power requirement Power consumption Power on Power off Temperature Operating Storage Operating position Dimensions W x Hx D Weight Format Maximum recording time SP EP VIDEO AUDIO Signal system Recording Playback system Signal to noise ratio Horizontal resolution VHS S VHS Frequency range Normal audio Hi Fi audio Input Output TUNER Tuning system Channel coverage VHF UHF CATV RF output TIMER Clock reference Program capacity Memory backup time ACCESSORIES Provided accessories AC 120 V 60 Hz 26W 2 5 W 5 C to 40 C 41 F to 104 F 20 C to 60 C 4 F to140 F Horizontal only 435 mm x 105 mm x 343 mm 17 3 16 x 4 3 16 x 13 9 16 4 9 kg 10 8 Ibs S VHS VHS NTSC standard 210 min with ST 210 video cassette 630 min with ST 210 video cassette NTSC type color signal and EIA monochrome signal 525 lines 60 fields DA 4 Double Azimuth head helical scan system 45 dB 230 lines 400 lines 70 Hz to 10 000 Hz 20 Hz to 20 000 Hz RCA connectors IN x 2 OUT x 1 S video connectors IN x 2 OUT x 1 Frequency synthesized tuner Channels 2 13 Channels 14 69 113 Channels Channel 3 or 4 switchable preset to Channel 3 when shi
37. 1 800 537 5722 http www jvc com Dear Customer In order to receive the most satisfaction from your purchase please read the instruction booklet before operating the unit In the event that repair is necessary or for the address nearest your location within the Continental United States please call 1 800 537 5722 for your nearest authorized servicer or visit our website at www JVC com Remember to retain your Bill of Sale for Warranty Service JVC JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP Sophisticated electronic products may require occasional service Just as quality is a keyword in the engineering and production of the wide array of JVC products service is the key to maintaining the high level performance for which JVC is world famous The JVC service and engineering organization stands behind our products NATIONAL HEADQUARTERS JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP 10 New Maple Avenue Pine Brook NJ 07058 9641 ACCESSORIES Don t service the product yourself To purchase accessories for your JVC product you may contact your local JVC Dealer CAUTION To prevent electrical shock do not open the cabinet From the 48 Continental United States call toll free 1 800 832 2345 or on the web at www JVC com There are no user serviceable parts inside Please refer to qualified service personnel for repairs _ 29 _ WARRANTY On
38. DBS selector to CABLE DBS then press one of the following buttons POWER TV CH and the Number keys e For some brands you must press ENTER after having pressed the Number keys to enter a channel number e To change the cable box s or DBS receiver s channels press TV CH or the Number keys The CH button can be used to change the VCR s channels only e To operate the VCR set the VCR TV CABLE DBS selector back to VCR CABLE BOX BRAND CODE ARCHER 01 05 17 CABLETENNA 0147 CABLEVIEW 15 16 17 21 25 CITIZEN 15 16 17 21 25 CURTIS 02 DIAMOND 01 17 GC BRAND 15 16 17 21 25 GEMINI 15 GENERAL INSTRUMENTS 01 04 06 11 12 15 28 10 18 23 15 01 04 06 11 12 15 28 NOVAVISION OAK PANASONIC REMBRANDT SAMSUNG SCIENTIFIC ATLANTA SIGMA SL MARX SPRUCER STARGATE TELEVIEW TOCOM UNIKA UNIVERSAL VIDEOWAY ZENITH 05 16 17 24 25 13 14 05 15 16 17 21 24 25 05 16 24 01 04 16 01 17 16 17 25 03 09 22 03 09 22 JVC DISH Network ECHOSTAR DISH Network SONY DSS RCA DSS Changing Remote Control Code This Remote is capable of transmitting two different control codes A code control signals or B code control signals This Remote is preset to send A code signals because your VCR is initially set to respond to A code signals You can easily change your Remote and VCR to send and respond to B code signals When using two JVC VCRs set the two VCRs
39. DISPLAY button TIMER buron D INSERT bu utton 0 STOP EJECT A button 22 CH buttons REC LINK lamp Rear Panel AC power cord AUDIO VIDEO OUT connectors AUDIO VIDEO IN connectors 0 S VIDEO OUT connector S VIDEO IN connector O JLIP terminal ANTENNA IN terminal REMOTE PAUSE AV COMPULINK terminal CABLE BOX Controller connector TV OUT terminal Audio level indicator O Start Time Indicator PP Stop Time Indicator 1 Symbolic mode indicators A DUB PLAY FF REW VARIABLE A DUB PAUSE SEARCH INSERT STILL SLOW Es INSERT PAUSE RECORD AV DUB RECORD PAUSE AV DUB PAUSE O Timer mode indicator S VHS indicator O Tape speed indicators Tape remaining time indicator Cassette mark VCR mode indicator Channel and auxiliary input L 1 and F 1 Counter remain display Clock time On Screen Display If you press OSD or OK on the Remote when SUPERIMPOSE is set to ON lt pg 20 you can see the current VCR status on the TV screen The indications are not recorded even if the VCR is in the recording mode femas RECORD 125 RECORD o Thu 12 00 AM PAUSE l o ot SAP TIMER RECORDING T i A oT TO START SOON _ o CANCEL do F INDEX ra aed NORM REMAIN 10 ste 0 no FI COUNT 1 23 45 Remote IE K o Te stop poate cH ng o l Se PROGRAMMING
40. El During recording press PAUSE II to engage the Record Pause mode Pl On the VCR Turn the ADVANCED JOG dial to the left or right and release it at the point where you want to resume recording On the Remote Hold down REW lt lt or FF gt gt or turn the JOG dial and release it at the point where you want to resume recording E Press PLAY gt when you wish to resume recording Adjusting recording level You can adjust the audio recording level manually EE Access Main Menu screen then Recording Level Control screen Press MENU on the Remote Press AV to move the highlight bar arrow to REC VIDEO NAVIGATION LEVEL CTL then press OK or gt MAIN MENU FUNCTION SET TUNER SET PRESS 4 THEN OK PRESS MENU TO END REC LEVEL CONTROL FA Adjust recording level Press A or V Press A or V briefly 5 times to move audio levels by one division on the scale To move the audio levels faster press and hold A or V e Adjust the recording level while watching the audio level indicator on the VCR s display panel Set the level so that maximum volume causes the indicator to vary between OdB to 4cB Press MENU to return to normal screen NOTES e Noise will increase if the recording level is too low while distortion will increase if the level is too high e When you finished audio recording be sure to set the level control back to its center position MIN MAX PRESS 4 PRES
41. ILY 9 WEEKLY PRESS NUMBER KEY 0 9 THEN OK STOP STOP TIME SP EP RESS PROG TO END PRESS PROG TO END e If the Guide Channel Set screen appears after pressing OK press the Number keys CH or AV to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR or cable box then press OK e To set the tape speed press SP EP 4 e To change the stop time press STOP e To timer record daily Monday Friday or weekly serials press DAILY M F Number key 8 or WEEKLY Number key 9 Pressing the button again makes the DAILY or WEEKLY display disappear e If you made a mistake press CANCEL to access the PlusCode No screen again e If an incorrect PlusCode number or the one for a broadcast already finished has been inputted ERROR is displayed for about 5 seconds then the PlusCode No screen reappears EJ Press OK or PROG e If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears see Program overlap warning display lt gt pg 16 Pl Press TIMER The VCR turns off automatically and is displayed on the display panel GUIDE CHANNEL SET GUIDE CH 312 VCR CH PRESS NUMBER KEY 0 9 OR a v THEN OK PRESS PROG TO END j Express Timer Programing Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically El Press PROG on the Remote
42. JVC LPT0639 001A NIN OX ANENG LANG LANANGE NAGA NA NG NA KH A KE NANA RE a EN ETAN a 4 Connections and Plug amp Play Setting cccccsscscssscssesesssesecesececes 6 nila SeMS sasananing aaa en ba adana Dah erence 7 ban ouae e SOUS saadung aaa tele and aaag i Clock SEN ata see ANA iad kada a aa gah a a ad eee ah ka aaa d 7 TUNEL OCHIN aaa ga ea Ae aa a Kaka admires aaa gan Nak 8 Cable Box and or DBS Receiver Control Setting 0 0 0 0 8 PUY OGCK EE AO nona aa inaa A a anga apalena angun 9 Recordin asasaran adandana adana etane b kaanan gae naa nangani banah aan 12 Timer RetOrdintszsss sanan SN A Ba Na Na a eee 14 Changing VCR Plust Setting 00000000 eaaae ona nenen 14 VCR Pluss Timer Frograming sajan aka alae ajaa ag a na a Aa aa a a 14 EXPRESS iMG hill BEA HANG sasana aga aa aga SAN A 15 24AFHR QUICK Programing sasa saa e a Jaa aa ANA Na AB NA AN aan 15 Video Navigation s sas asas asa edane andon dakan dan aaa nga aan ain sias 16 Navigation Playback saena Salawat a aa e aa ka aa ank ad aia naa 16 CUMS TING nanas a aaa aana aa apa aa kaa ak aa ena acy a A daana aana 17 PINGIMID TIM GS na aaa aaa cree ta hac pana aa D aaa aa gaga a a aaa aaa 18 Other FUNCHIONS lt 5s csscsssccapsncesootesoscatucdeesanSeasetesccoscuicedysasdbeiscesnees 19 Timer wanine depay saxo ie agak kaanan a Bana a aana gan a 19 CHECKING tape POSON aas aaa Aa crate ine ent Aa a BAN alaa 19 Changing display
43. NPUT to S VIDEO When using S VIDEO IN connector on the rear panel set REAR AUX INPUT to S VIDEO When using VIDEO input connector on the front panel set FRONT AUX INPUT to VIDEO When using VIDEO IN connector on the rear panel set REAR AUX INPUT to VIDEO E Select edit mode Set the edit mode to ON for the VCRs if such a mode is equipped e On this VCR set PICTURE CONTROL to EDIT CF pg 20 EJ Start playback Press PLAY BP on the playback VCR Start recording Press REC on the recording VCR NOTE Be sure to select AUTO for PICTURE CONTROL or NORM when VIDEO CALIBRATION is set to OFF after you finish dubbing the tapes pg 20 Audio Dubbing Audio Dubbing replaces a previously recorded normal audio track with a new soundtrack EF Make connections Connect an audio cable between the VCR s audio input connectors and the audio component s audio output connectors When connecting a monaural audio component use only the VCR s AUDIO L input connector e Audio Dubbing is possible only by using the audio input connectors on the front panel or on the rear panel This VCR To AUDIO input T fT To audio output CD player etc PA Select input location Select F 1 when connecting the audio component to the audio input connectors on the front panel Select L 1 when connecting the
44. NU after the clock has been set the Brand Set screen appears I Enter brand code and perform test Press the appropriate Number keys on the Remote to enter the brand code from the following list then press OK or gt CABLE BOX BRAND SET De 2 S PRESS NUMBER KEY 0 9 N OK TO TEST PRESS MENU TO END ARCHER CABLETENNA CABLEVIEW CITIZEN CURTIS DIAMOND GC BRAND 15 16 17 21 25 GEMINI 15 GENERAL INSTRUMENTS 1 4 6 11 12 15 28 HAMLIN 10 18 23 JASCO 15 JERROLD 1 4 6 11 12 15 28 NOVAVISION 2 8 OAK 7 20 PANASONIC 13 14 15 16 17 21 25 15 16 17 21 25 15 16 17 21 25 PULSER RCA 13 14 REGAL 10 18 23 REMBRANDT SAMSUNG SCIENTIFIC ATLANTA SIGMA 1 16 17 SL MARX SPRUCER STARGATE TELEVIEW TOCOM UNIKA UNIVERSAL VIDEOWAY ZENITH 5 16 17 24 25 13 14 5 15 16 17 21 24 25 5 16 24 DBS RECEIVER BRAND CODE DBS RECEIVER BRAND 51 JVC DISH Network ECHOSTAR DISH Network SONY DSS 51 RCA DSS For cable box CABLE BOX BRAND SET e If the cable box s channel changes to 9 i setting is complete Press OK ji vin BAREH e If the cable box s channel does not CHANGE TO CHANNEL 09 change to 9 NO 1 Press AV to move the highlight bar PRESS MENU TO END arrow to NO then press OK or b 2 Repeat step MY until the cable box s channel changes to 9 by entering another code 3 If the channel does not change after going thr
45. PRESS WARRANTY HEREIN JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT INCONVENIENCE LOSS OR ANY OTHER DAMAGES WHETHER DIRECT INCIDENTAL OR CONSEQUENTIAL INCLUDING WITHOUT LIMITATION DAMAGE TO TAPES RECORDS OR DISCS RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so these limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state JVC COMPANY OF AMERICA 1700 Valley Road DIVISION OF JVC AMERICAS CORP Wayne New Jersey 07470 REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY THIS WARRANTY DOES NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT For customer use Enter below the Model No and Serial No which is located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No Purchase date Name of dealer Memo as ga VICTOR COMPANY OF JAPAN LIMITED Printed in Malaysia COPYRIGHT 2002 VICTOR COMPANY OF JAPAN LTD
46. R checks the condition of the tape in use during playback and recording and compensates to provide the highest possible pictures This takes place whenever you play back a tape or start recording after inserting a tape NOTE The VCR checks the tape condition for about 7 seconds then starts recording To make sure you record the desired scene or program completely perform the following steps Press and hold PAUSE Ill and press REC 6 After about 7 seconds the VCR re enters Record Pause mode 2 Press PLAY B gt to start recording PO CONTINUED ON NEXT PAGE 19 WH PICTURE CONTROL AUTO NORM EDIT SOFT SHARP This function helps you to adjust the playback picture quality according to your preference AUTO NORM Normally select this Picture quality is adjusted automatically When VIDEO CALIBRATION is OFF NORM will appear instead of AUTO EDIT Minimizes picture degradation during editing recording and playback SOFT Reduces image coarseness when viewing overplayed tapes containing much noise SHARP Clearer sharper edged picture when viewing images with much flat same colored surfaces such as cartoons NOTE Select EDIT when you are editing tapes After you finish editing the tapes select AUTO Hi AUTO TIMER ON OFF e When this function is set to ON The timer recording standby mode is automatically engaged when the VCR is turn
47. S MENU TO END fo Timer Recording Up to 8 timer recording programs can be made using VCR Plus timer programing Express timer programing or 24HR Quick Programing method as far as a year in advance Remember the clock must be set before you can program the timer e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR NOTES fall the 8 programs have already been set PROGRAM FULL or Full appears on the TV screen or the display panel After timer recording is completed the VCR turns off automatically You can program the timer recording while a regular recording is in progress the menu screens will not be recorded e To timer record cable or satellite channels perform Cable Box and or DBS Receiver Control Setting pg 8 and be sure to keep the cable box or DBS receiver turned on Even if a power failure occurs the VCR keeps your timer programs However the clock time channel settings and other menu settings are lost As a result when the power is supplied again to this VCR after the power failure this VCR starts the Plug amp Play setting automatically to restore the clock time and channel setting If the clock time and channel setting are restored correctly each timer program you have made will start at its start time unless its end time has elapsed f the tape reaches its end during timer recording
48. TV and the VCR only using the RF connection press TV VCR on the Remote so that the VCR mode indicator lights on the display panel to view the program to be recorded EJ Set tape speed Press SP EP AJA The selected tape speed will appear on the display panel and on the TV screen NOTE You can select tape speed in the stop mode or during recording pause mode E1 Start recording On the VCR Press REC On the Remote While holding REC 6 press PLAY P NOTES e If VIDEO CALIBRATION is set to ON F pg 19 default setting the VCR takes about 7 seconds to assess the quality of the tape in use then recording begins with the picture level optimized If MEMORY FULL appears on the TV screen when you start recording the VCR s memory for the Video Navigation function is full This is not related to actual recording but the program information will not be stored in the VCR s memory pg 16 Video Navigation During recording Pause recording Press PAUSE II e Press PLAY B to resume recording You can select channel in the recording pause mode Stop recording On the VCR Press STOP EJECT W 4 On the Remote Press STOP W NOTE If the tape reaches its end during recording the recording stops and 00 on the display panel blinks Press STOP EJECT amp on the VCR to eject the cassette or press REW 44 on the Remote or turn the ADVANCED JOG dial to t
49. US PAGE gt AV COMPU LINK FRONT AUX INPUT REAR AUX INPUT VIDEO SELECT WITH 4 7 AND OK PRESS MENU TO END E Change setting Press OK or The default setting is bold in the table below Press MENU to return to normal screen After a power failure occurs Function Settings will be reset to its default setting E S VHS ET ON OFF When this function is set to ON you can record on VHS cassettes with S VHS picture quality Tapes recorded using this function can be played back on most of S VHS VCRs or VHS VCRs equipped with the SQPB S VHS QUASI PLAYBACK function When this function is set to ON the S VHS indicator lights up on the display panel NOTES e Before recording set VIDEO CALIBRATION to ON c See below You cannot activate the S VHS ET function while recording timer recording or Instant Timer Recording pg 13 or the VIDEO CALIBRATION function See below is in progress e The S VHS ET function does not work with S VHS cassettes To keep the highest quality recording and playback pictures over a long period of time S VHS recording on S VHS cassettes is recommended e Use of high grade tapes is recommended for S VHS ET recordings On some tapes picture quality will not improve even if the S VHS ET function is used Check the recording quality before you start important recordings E VIDEO CALIBRATION ON OFF When this function is set to ON this VC
50. V mode on the TV You can now perform basic playback or basic recording e If you connect the TV and the VCR only using the RF connection press TV VCR on the Remote so that the VCR mode indicator lights on the display panel Initial Settings Language Setting The default setting is ENGLISH e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR MAIN MENU FUNCTION SET TUNER SET gt INITIAL SET EC LEVEL CTL VIDEO NAVIGATION EE Access Main Menu screen then Initial Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt PRESS a v THEN OK PRESS MENU TO END PI Select language This VCR offers you the language choice to view menus and some messages in English Spanish or French Press AV to move the highlight bar arrow to LANGUAGE then press OK or gt repeatedly until the desired language is selected Press MENU to return to normal screen Language selection will be reset to ENGLISH after a power failure occurs Clock Setting Perform clock setting only if the clock has not been set correctly by the Plug amp Play setting or if you use a cable box INITIAL SET CLOCK SET LANGUAGE ENGLISH GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET JLIP ID NO SET SELECT WITH 4 AND OK PRESS MENU TO END e Turn on the VCR a
51. and Sc on the e The timer is engaged but there is no cassette e Insert a cassette on which the record safety tab is display panel will not stop loaded intact or cover the hole with the adhesive tape blinking e The loaded cassette has had its record safety tab Remove the cassette and cover the hole with removed adhesive tape or load a cassette on which the record safety tab is intact blinks for 10 seconds f TIMER has been pressed when there are no Check the programed data and set again if and the timer mode is programs in memory or the timer recording necessary then press TIMER again disengaged program has not been set correctly The power shuts off and e The tape reaches its end during timer recording The program may not have been recorded in its and LA will not entirety Next time be sure you have enough time stop blinking on the tape to record the entire broadcast Timer recording begins as Even though you do not use an external cable box f Set CABLE BOX SET to OFF or DBS RECEIVER scheduled but the channel or DBS receiver CABLE BOX SET is set to ON SET is set to OFF pg 9 is always incorrect or DBS RECEIVER SET is set to ON You moved and now VCR J The receivable stations in the new area are e Re perform the procedure in Changing VCR Plus system does not received on different channels than those in the Plus Se
52. and their Remotes to different codes so that the Remotes can operate the VCRs separately Set the VCR TV CABLE DBS selector on the Remote to VCR EF Set remote control code for Remote Press and hold A B Press the Number key 2 Press STOP W and release A B The Remote now can transmit B code control signals VI Check remote control code for VCR Press and hold on the VCR for more than 5 seconds while the VCR is turned off The code currently set appears on the display panel leo n gt EJ Change code for VCR Press any key on the Remote The VCR now responds to B code control signals e To set the Remote and the VCR to transmit and respond to A code control signals repeat above procedure as shown above except press the Number key 1 in step 2 of E To control two VCRs with the same Remote You can control two JVC VCRs by switching the remote control code for the Remote between A and B step Ml keeping two VCRs to different control codes e To change only the remote control code for the Remote DO NOT perform steps H and E l Editing Various connection for editing tapes The following three methods can be used for editing tapes VHS to S VHS editing VIDEO VIDEO connection Although the picture quality is inherently limited by the original VHS quality the edited tape has better picture quality than those made by VHS to VHS editing S VHS to VHS editin
53. ape or program from the VCR s memory Press MENU to return to normal screen Finding Titles Preparations MAIN MENU FUNCTION SET TUNER SET EE Access Main Menu screen then Video Navigation screen Press MENU on the Remote Press AV to NITIALSET move the highlight bar arrow to VIDEO NAVIGATION then press OK or gt PRESS 4 THEN OK PRESS MENU TO END VI Access Find Title screen Press AV to move the highlight bar arrow to FIND TITLE then press OK or gt VIDEO NAVIGATION EDIT TITLE FIND TITLE FIND BLANK SPACE CHECK MEMORY NAVIGATION ON NOTE You can display the Find Title screen on the TV screen by pressing NAVIGATION on the Remote when no cassette is inserted SELECT WITH a v AND OK PRESS MENU TO END Finding by tape number First follow steps MH to Bl in Preparations above then go to the following steps Kl Access tape number screen Press AV to move the highlight bar arrow to TAPE NO then press OK or gt FIND TITLE gt TAPE NO DATE CATEGORY PRESS 4 THEN OK PRESS MENU TO END FA Select tape number me ana Press AV to move the highlight bar rs 16 BRAZIL 12 28 01 56 GOLDE 12 25 01 arrow to the tape number you want to 0999 99 900P b k h OK 99 1000A play back then press 1 915A e To go to another page of the lists press lt PRESS a v THEN OK or gt PAGE lt gt END MENU e If the selecte
54. ase for forward slow motion Press PAUSE ll and release again to return to still picture Variable Speed Picture Search Turn the ADVANCED JOG dial to the right for forward variable speed search or to the left for reverse variable speed search Press PLAY to resume normal playback e Each time the ADVANCED JOG dial passes a click position the playback speed changes To decrease the speed during picture search turn the dial in the opposite direction On the Remote During playback Stop playback Press STOP W Pause playback and view still picture Press PAUSE Press PLAY B gt to resume normal playback Pause and Frame by Frame playback Press PAUSE ll to pause OR Press PAUSE ll to pause then press lt for reverse then press JOG SHUTTLE so frame by frame playback or that the button lights up Turn gt or PAUSE II for the JOG dial to the right for forward frame by frame forward frame by frame playback repeatedly playback or to the left for reverse frame by frame playback Press PLAY to resume normal playback High Speed Picture Search During playback or still press REW 4441 for reverse high speed search or FF BP for forward high speed search OR During playback or still press JOG SHUTTLE so that the button lights up Turn the SHUTTLE ring all the way to the right for forward high speed search or to the left for reverse high speed search Release the SHUTTLE
55. ating these openings must not be blocked or covered e Do not block the openings by placing the product on a bed sofa rug or other similar surface e Do not place the product in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 6 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer ANTENNA INSTALLATION INSTRUCTIONS 1 Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding connectors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode 2 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 3 Power Lines An outside antenna system should not be located in the vicinity of overhead
56. ation function EE Access Main Menu screen then Video Navigation screen TUNER SET Press MENU on the Remote Press AV to Reet CTL move the highlight bar arrow to VIDEO NAVIGATION then press OK or gt PRESS a v THEN OK PRESS MENU TO END MAIN MENU FUNCTION SET PI Deactivate Video Navigation Press AV to move the highlight bar arrow to NAVIGATION then press OK or gt Press MENU to return to normal screen NOTES Video Navigation is possible only with the cassettes recorded on this VCR To record the date and time as the program title in this VCR s memory make sure the VCR s clock is set correctly before recording e Jo record the program information in this VCR s memory you must continue to record each program for over the minimum recording time 5 minutes for the SP mode or 15 minutes for the EP mode e During playback or when searching for the beginning of a program a VCR might find two different tape numbers recorded on a tape After you remove this tape the tape will be assigned just one tape number the smaller one After this the higher tape number will be missing from the memory s tape number list e Tape program information is stored in this VCR s memory If this VCR s memory is damaged and the program information is lost VIDEO NAVIGATION EDIT TITLE FIND TITLE FIND BLANK SPACE CHECK MEMORY gt NAVIGATION OFF SELECT WITH a v AND OK PRESS
57. ation on this VCR Select L 1 when connecting the camcorder to the audio video or S video input connectors on the rear panel Select F 1 when connecting the camcorder to the audio video or S video input connectors on the front panel On the VCR Press CH or push the ADVANCED JOG dial then turn it to the left or right until L 1 or F 1 appears on the display panel On the Remote Press AUX and or CH until L 1 or F 1 appears on the display panel El Select video input connector Select the appropriate mode depending on the connector being used pg 21 When using S VIDEO input connector on the front panel set FRONT AUX INPUT to S VIDEO When using S VIDEO IN connector on the rear panel set REAR AUX INPUT to S VIDEO When using VIDEO input connector on the front panel set FRONT AUX INPUT to VIDEO When using VIDEO IN connector on the rear panel set REAR AUX INPUT to VIDEO EJ Select edit mode Set PICTURE CONTROL to EDIT CF pg 20 EJ Set AV COMPU LINK mode If your JVC camcorder is equipped with a Master Edit Control set AV COMPU LINK to OFF pg 21 The REMOTE PAUSE AV COMPULINK connector works as a Remote Pause connector Start playback Set the camcorder to its play mode NOTE If the camcorder is equipped with a superimpose OSD disable feature set it to OFF before starting playbac
58. d cassette has already been loaded playback begins automatically kl Load cassette Insert the tape of the selected number Playback begins automatically INSERT TAPE 0998 PRESS MENU TO END Finding by recording date First follow steps fl to Bl in Preparations above then go to the following steps 1 Access date screen FIND TITLE Press AV to move the highlight bar TAPE NO gt DATE arrow to DATE then press OK or gt CATEGORY PRESS a v THEN OK PRESS MENU TO END PI Select tape number Press AV to move the highlight bar arrow to the tape number you want to play back then press OK e If the selected cassette has already been loaded playback begins automatically EJ Load cassette Insert the tape of the selected number e Playback begins automatically oo TITLE 1 100 0993 LOST WORL DERU gt 0998 99 1000A_ 12 30 01 FOOTBALL 12 26 01 F1 BRAZIL 12 26 01 007 GOLDE 11 15 01 181 115P 11 14 01 PRESS a v THEN OK TO SEARCH PAGE 4 gt END MENU INSERT TAPE 0998 PRESS MENU TO END Finding by category First follow steps fl to A in Preparations above then go to the following steps 1 Access Category screen FIND TITLE Press AV to move the highlight bar TAPE NO arrow to CATEGORY then press OK or gt PRESS a v THEN OK PRESS MENU TO END FA Select category Press AV to move the highlight bar arrow to th
59. e category you want then CHILDREN press OK SHOPPING PRESS a v THEN OK PRESS MENU TO END EJ Select tape number oo MOVIE 1 3 0993 LOST WORL _ 1 15 02 Press AV to move the highlight bar gt 0998 99 1000A__ 12 30 01 0999 FOOTBALL 12 26 01 arrow to the tape number you want to 0999 F1BRAZIL 12 26 01 0999 007GOLDE 11 15 01 play back then press OK 0994 181 115P 11 14 01 PRESS 4 Y THEN OK RCH e f the selected cassette has already been NCK PAGE lt 4 gt END MENU loaded playback begins automatically EJ Load cassette Insert the tape of the selected number e Playback begins automatically INSERT TAPE 0998 PRESS MENU TO END Finding blank space MAIN MENU FUNCTION SET TUNER SET INITIAL SET REC LEVEL CTL gt VIDEO NAVIGATION PRESS a v THEN OK PRESS MENU TO END EE Access Main Menu screen then Video Navigation screen Press MENU on the Remote Press AV to move the highlight bar arrow to VIDEO NAVIGATION then press OK or D PI Access Find Blank Space screen Press AV to move the highlight bar arrow to FIND BLANK SPACE then press OK or gt VIDEO NAVIGATION EDIT TITLE FIND TITLE gt FIND BLANK SPACE CHECK MEMORY NAVIGATION ON SELECT WITH a v AND OK PRESS MENU TO END NG E Select tape number a gt a3 1 15 02 Press AV to move the highlight bar arrow to the tape number on which you want to record a
60. ed off It is temporarily canceled when the VCR is turned on You do not have to press TIMER to engage or disengage the timer recording standby mode e When this function is set to OFF You have to press TIMER to engage or disengage the timer recording standby mode Hi SUPERIMPOSE ON OFF When this function is set to ON various VCR status information on screen display appears on the screen NOTE When you use this VCR as the playback VCR for editing a tape be sure to set this function to OFF otherwise the VCR status information on screen display will be recorded on the edited tape Hi AUTO SP EP TIMER ON OFF When this function is set to ON the VCR automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer recording in SP mode For Example Recording a program of 140 minutes in length onto a 120 minute tape Approximately 110 minutes Approximately 30 minutes NOTES If you have programed the VCR to timer record 2 or more programs do not use this function but change the tape speed manually during timer programing e There may be some noise and sound disturbance where the tape speed switches from SP to EP mode on the tape This function is not available during ITR Instant Timer Recording and will not work properly on the following tapes T ST 30 T ST 60 T ST 90 and T ST 120 Hi DIGITAL R3
61. el or AV mode e Set the VCR TV CABLE DBS selector on the Remote to TV ET Turn on TV Turn on the TV using the Power button on the TV or its Remote VI Set TV brand code Press and hold POWER on the Remote Press the Number keys to enter your TV s brand code Press STOP W and release POWER The TV should turn off EJ Operate TV First set the VCR TV CABLE DBS selector to TV then press one of the following buttons POWER TV VCR TV CH I TV Muting TV VOL and the Number keys For some brands you must press ENTER after having pressed the Number keys to enter a channel number e To operate the VCR set the VCR TV CABLE DBS selector back to VCR TV BRAND CODE TV BRAND CODE 07 JVC HITACHI MAGNAVOX MITSUBISHI PANASONIC RCA SHARP Cable Box or DBS Receiver Brand Setting e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to CABLE DBS GE Turn on cable box or DBS receiver Turn on the cable box or DBS receiver using the Power button on the unit or its Remote VI Enter brand code Press and hold POWER on the Remote Press the Number keys to enter your cable box s or DBS receiver s brand code Press STOP W and release POWER The cable box or DBS receiver should turn off eo EJ Operate cable box or DBS receiver First set the VCR TV CABLE
62. emote to select the desired monitor sound pg 11 WH S VHS MODE ON OFF You can determine which recording mode either S VHS mode or VHS mode is used for recording on S VHS tapes e When this function is set to ON you can record on S VHS tapes with S VHS picture quality e When this function is set to OFF you can record on S VHS tapes with VHS picture quality NOTES e S VHS mode allows you to make high quality video recordings with horizontal resolution of 400 lines comparing with the 230 lines of resolution of conventional VHS recordings To achieve the highest quality picture we recommended to record in S VHS mode But remember that a conventional VHS VCR without SQPB cannot play back S VHS tapes recorded in S VHS mode e S VHS MODE setting does not affect recording on VHS tapes Recording on VHS tapes is always performed in VHS mode except when using S VHS ET mode lt gt pg 19 ay o Te Hi AV COMPU LINK ON OFF The REMOTE PAUSE AV COMPULINK terminal on the rear panel can be used as either the REMOTE PAUSE terminal or the AV COMPULINK terminal e When this function is set to ON you can use this terminal as the AV COMPULINK terminal By connecting other JVC s AV COMPULINK components including amplifiers or receivers and televisions one touch control of the audio and video components linked via their AV COMPULINK connectors becomes possible e When this function is set to
63. ess AV to move the highlight bar arrow to GUIDE CHANNEL SET then press OK or D Input guide channel number Press AV or the Number keys to select the VCR Plus guide channel number as shown in the TV listing then press OK or GUIDE CHANNEL SET S VCR CH 4 5 PRESS NUMBER KEY 0 9 OR 4 THEN OK PRESS MENU TO END El Input receiving channel number Press AV or the Number keys to select the number of the channel on which the guide channel s broadcasts are received then press OK or gt e Repeat steps KA and f for each instance EJ Return to normal screen Press MENU on the Remote GUIDE CHANNEL SET GUIDE CH 3 amp VCR CH 47 PRESS NUMBER KEY 0 9 OR 4 THEN OK PRESS MENU TO END VCR Plus Timer Programing The PlusCode programing numbers are the numbers next to the program in most TV listing Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically El Press PROG onthe Remote to access the PlusCode No screen PLUSCODE NO PRESS NUMBER KEY 0 9 PRESS TO SET EXPRESS PROGRAMMING PRESS PROG TO END PI Press the appropriate Number keys to input the PlusCode number then press OK or Check to make sure the setting is accurate on the Program screen PROGRAM 1 PLUSCODE NO PLUSCODE NO 12345678 1234567 8 IN 8 00PM gt 10 00PM DATE CH 12 24 02 12 SP TUE PRESS 8 DA
64. ess Main Menu screen then Tuner Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to TUNER SET then press OK or gt VI Perform Auto Channel Set Press AV to move the highlight bar arrow to AUTO CHANNEL SET then press OK or The VCR selects the correct band TV or CATV automatically during Auto Channel Set When Auto Channel Set is complete SCAN COMPLETED appears on screen e f the scan was unsuccessful SCAN COMPLETED NO SIGNAL appears on screen Check the connections and start again Press MENU to return to normal screen MAIN MENU FUNCTION SET gt TUNER SET INITIAL SET REC LEVEL CTL VIDEO NAVIGATION PRESS a v THEN OK PRESS MENU TO END TUNER SET BAND CATV gt AUTO CHANNEL SET MANUAL CHANNEL SET SELECT WITH 4 AND OK PRESS MENU TO END AUTO CHANNEL SET SCANNING PRESS MENU TO END Setting channels manually Manual Channel Set You can add the channels you want or delete the channels you do not want manually MAIN MENU FUNCTION SET EE Access Main Menu screen then Tuner Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to TUNER SET then press OK or gt REC LEVEL CTL VIDEO NAVIGATION PRESS a w THEN OK PRESS MENU TO END VI Access Manual Channel Set screen Press AV to move the highlight bar arrow to MANUAL CHANNEL SET then press OK
65. g VIDEO VIDEO connection Since the original source is recorded in S VHS mode the edited tape has better picture quality than those made by VHS to VHS editing S VHS to S VHS S VIDEO connection Original picture quality of S VHS made can be duplicated with minimal picture degradation This is the best editing method you can use on S VHS VCRs Editing from Camcorder You can use a camcorder as the playback unit and your VCR as the recording VCR Refer also to the camcorder s instruction manual for connection and its operations EE Make connections This VCR for recording To AUDIO VIDEO 1 1 1 1 To S VIDEO input input EEE E E Ed To rear panel l REMOTE PAUSF AV COMPULINK S video cable supplied Audio video cable supplied To audio video pee bd To S video output To EDIT GA KK EN NG Ngga ge an ee Camcorder for playback Mini plug cable not supplied JVC camcorder only When the JVC camcorder is equipped with the Master Edit Control you can control the VCR from the camcorder Connect the mini plug cable not supplied with this VCR as illustrated e If camcorder is monaural connect the audio output connector on the camcorder to the left audio input connector on this VCR VI Load cassettes Insert the playback cassette into the camcorder and the cassette to be recorded on into this VCR EJ Select input location on this VCR Select the correct external input loc
66. graming function the program overlap warning display does not appear even if some programs overlap each other To use the VCR while it is in timer recording standby mode Press TIMER then press POWER After you use the VCR press TIMER again to put the VCR into timer recording standby mode Checking canceling or changing program settings Kl Disengage timer Press TIMER then press POWER e When AUTO TIMER is set to ON lt pg 20 you do not have to press TIMER PI Access Program Check screen Press PROG CHECK Access Program screen Press PROG CHECK again Each time you press PROG CHECK the next program s Program screen appears El Cancel or change program setting To cancel a program press CANCEL when the Program screen you do not want is shown To change a program press the appropriate button START STOP DATE CH DAILY M F Number key 8 WEEKLY Number key 9 and or SP EP 4 47 when the Program screen on which you want to make changes is shown EJ Return to normal screen Press PROG CHECK repeatedly until no Program screen is shown EJ Reengage timer recording standby mode Press TIMER The VCR turns off automatically and D is displayed on the display panel e When AUTO TIMER is set to ON CF pg 20 the timer recording standby mode automatically resumes when you turn off the VCR R START STOP CH 8 00P 10 00
67. han 5 seconds The play indicator 1 on the display panel starts blinking slowly To stop playback press STOP MM on the Remote or STOP EJECT W 4 on the VCR Locating beginning of recordings Index Search When recording on this VCR index codes are placed on the tape at the beginning of each recording EE While the tape is not running press Md or BPI on the Remote to start search PA To access a recording of 2 to 9 index codes away press Md or gt gt repeatedly until the correct number is displayed on the screen only if SUPERIMPOSE is set to ON C pg 20 Playback begins automatically when the desired recording is located Beginning of the Current Beginning of the current program position on 2nd next program recorded the tape recorded Previous Next program program recorded 2nd next recorded 1 lt lt Locating beginning of timer recordings Instant Review After ensuring that the VCR is turned off and that the timer mode is disengaged press REVIEW e The VCR turns on and rewinds to the index code indicating the beginning of the last timer recorded program then begins playback automatically You can access a program of 2 to 9 index codes away from the current position on the tape If for example you have 5 programs recorded and you want to watch the third one press REVIEW three times e The Instant Review function will also operate if the VCR is turned on Skipping
68. hannel number the clock time and the tape remaining time alternatively e To reset the time counter press C RESET on LI TI the Remote JAAN e During playback the channel number is not shown ees e When the tape remaining time appears PLI LI PM also lights on the display panel 8 e When SUPERIMPOSE is set to ON C pg 20 and DISPLAY on the Remote is pressed the current VCR status appear on the TV screen Function settings You can use the other useful function settings on the Function Set screen e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR MAIN MENU FUNCTION SET TUNER SET INITIAL SET EE Access Main Menu screen then Function Set screen Press MENU on the Remote Press AV to REC LEVEL CTL move the highlight bar arrow to VIEO NAVRATIO FUNCTION SET then press OK or ba PRESS av THEN OK PRESS MENU TO END FA Select Function Press AV to move the highlight bar arrow to the function you want to set FUNCTION PREVIOUS PAGE gt S VHS ET DIGITAL R3 ON VIDEO CALIBRATION VIDEO STABILIZER OFF PICTURE CONTROL BLUE BACK ON AUTO TIMER OFF 2ND AUDIO RECORD OFF SUPERIMPOSE ON AUDIO MONITOR HI FI AUTO SP gt EP TIMER OFF S VHS MODE ON NEXT PAGE NEXT PAGE SELECT WITH AY AND OK SELECT WITH AY AND OK PRESS MENU TO END PRESS MENU TO END PREVIO
69. he audio video input connectors on the TV S video Connection allows you to make the most of the S VHS picture performance If your TV is equipped with an S video input connector Perform RF Connection previously described Connect the supplied S video cable between the S VIDEO OUT connector on the rear of the VCR and the S video input connector on the TV 3 Connect an audio cable between the AUDIO OUT connectors on the rear of the VCR and the audio input connectors on the TV Even if you are using audio video cables to connect your VCR to your TV you must also connect it using the RF cable This will ensure that you can record one show while watching another El Perform Plug amp Play setup Plug the AC power cord into an AC outlet Do not turn on the VCR The clock and tuner channels will be set automatically The time and date can be set automatically by the clock setting data transmitted from one of the regular TV broadcast channels We call this TV channel the host channel and it is a PBS channel in your area ATTENTION e If you use a cable box Plug amp Play will not function set the clock and tuner channels separately gt pg 7 8 e Depending on area or reception conditions the VCR may not receive the Auto clock setting data from a PBS channel If this function is taking a considerable amount of time it may be necessary to perform the procedure in Semiauto Clock Set C pg 7 or Ma
70. he left on the VCR to rewind the tape Recording Features e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR Recording Resume Function If there is a power outage during recording or Instant Timer Recording or timer recording the recording will resume automatically when the power is restored to the VCR No setting is required for this function Specifying recording length Instant Timer Recording ITR During recording press REC on the VCR repeatedly until the recording length you want appears on the display panel The record indicator on the display panel starts blinking Each time you press the button recording length increases in 30 minute intervals up to 6 hours e The VCR shuts off after recording is finished e To cancel an ITR press STOP W on the Remote or STOP EJECT MI 4 on the VCR Watching one program while recording another During recording e If you connect the TV and the VCR only using the RF connection pg 6 to view pictures from the VCR press TV VCR on the Remote so that VCR mode indicator goes off from the display panel The TV broadcast being recorded disappears e If you are using the AV or S video connection C7 pg 6 to view pictures from the VCR change the TV s input mode from AV to TV Then select the channel you want to watch on the TV Second Audio Recording This VCR
71. host channel and D S T mode will be reset to AUTO after a power failure occurs Setting clock manually Manual Clock Set First follow steps fl to Bin Preparations above then go to the following steps ET Set time date and year CLOCK SET Press AM until the desired time appears SME OA eit then press OK or D Set the date and year AUTO CLOCK ON a ae HOSTCH AUTO CATV y D S T AUTO e Holding AV changes the time in 30 D AAN minute intervals or changes the date in 15 day intervals VI Select D S T mode CLOCK SET Press OK or gt to move the highlight bar to DM e D S T then press AV to select the AUTO CLOCK OFF desired setting ON Adjustment will be made by the MESET built in clock itself PRESS MENU TO END OFF Select when Daylight Saving Time does not apply to you EJ Start clock Press MENU and normal screen appears PRESS Aw THEN OK PRESS MENU TO END To make corrections any time during the process Press OK or gt repeatedly until the item you want to change blinks then press AV Manual setting of the clock will be lost after a power failure occurs Tuner Setting e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR Setting channels automatically Auto Channel Set Perform Auto Channel Set only if channels have not been set correctly by the Plug amp Play setting EE Acc
72. ifications not approved by JVC could void user s authority to operate the equipment Declaration of Conformity Model Number HR S9911U Trade Name JVC Responsible Party JVC Americas Corp Address 1700 Valley Road Wayne N J 07470 Telephone Number 973 317 5000 This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Failure to heed the following precautions may result in damage to the VCR Remote or video cassette 1 DO NOT place the VCR in an environment prone to extreme temperatures or humidity in direct sunlight in a dusty environment in an environment where strong magnetic fields are generated on a surface that is unstable or subject to vibration 2 DO NOT block the VCR s ventilation openings 3 DO NOT place heavy objects on the VCR or on the Remote 4 DO NOT place anything which might spill on the top of the VCR or on the Remote 5 AVOID violent shocks to the VCR during transport VCR Plus C and PlusCode are registered trademarks of Gemstar Development Corporation The VCR Plus system is manufactured under license from Gemstar Development Corporation DSS is an official trademark of DIRECTV Inc a unit of GM Hughes Electronics L P DISH Network is a trademark of
73. in S VHS mode or in S VHS ET mode lt pg 13 CONTINUED ON NEXT PAGE On the VCR During playback Stop playback Press STOP EJECT W 4 Pause playback and view still picture Press PAUSE II OR Push the ADVANCED JOG Press PLAY B to resume dial normal playback Push the ADVANCED JOG dial again to resume normal playback Pause and Frame by Frame playback Press PAUSE Hl to pause OR Push the ADVANCED JOG then press PAUSE IB dial to pause then turn the repeatedly to advance a still ADVANCED JOG dial to the picture right for forward frame by Press PLAY gt to resume frame playback or to the left normal playback for reverse frame by frame playback e Push the ADVANCED JOG dial again to resume normal playback High Speed Picture Search Turn the ADVANCED JOG dial quickly to the right for forward high speed search or to the left for reverse high speed search Press PLAY to resume normal playback Slow Motion Turn the ADVANCED JOG dial one click to the left for forward slow motion To play in reverse slow motion continue to turn the ADVANCED JOG dial to the left after selecting all the forward direction slow motion modes Press PLAY to resume normal playback NOTE During slow motion some noise may appear on the TV screen Press CH to eliminate the noise OR Press PAUSE ll to pause then press and hold PAUSE IN for more than 2 seconds then rele
74. information for the Video Navigation is deleted but the actual recorded program will not be erased EF Select program 000114 JVC NEWS 1 3 8 00PM 2 27 02 CH 5 10 OOPM_ 2 28 02 CH 16 Press AV to move the highlight bar arrow to the program you want to delete Tg rasa IOSA 20 EP TIT then press CANCEL PRESS a THEN OK TO EDIT OR CANCEL TO DELETE PRESS MENU TO END RY FA Delete program information Press AV to move the highlight bar k i DELETE arrow to YES then press OK or gt Press MENU to return to normal screen EATN PRESS 4 THEN OK PRESS MENU TO END Checking memory MAIN MENU FUNCTION SET TUNER SET EE Access Main Menu screen then Video Navigation screen Press MENU on the Remote Press AV to SETA Ge move the highlight bar arrow to VIDEO NAVIGATION then press OK or gt PRESS A w THEN OK PRESS MENU TO END PI Check memory Press AV to move the highlight bar arrow to CHECK MEMORY then press OK or gt VIDEO NAVIGATION EDIT TITLE FIND TITLE FIND BLANK SPACE CHECK MEMORY NAVIGATION ON CHECK MEMORY SELECT WITH a v AND OK PRESS MENU TO END PRESS MENU TO END e The Check Memory screen appears When the scale bar reaches 100 on the TV screen VCR s memory is full and MEMORY FULL appears If the VCR s memory becomes full the VCR cannot register any more information Delete any unnecessary data of t
75. ing unplugging the AC power cord or a power outage also releases the child lock e Even if the child lock function is in use it is possible to engage and disengage the timer mode with TIMER on the Remote Keep the Remote out of the children s reach e Timer recording programs will be performed even if the child lock function is activated Child lock indicator JLIP ID Number Setting e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR The JLIP Joint Level Interface Protocol terminal is used to connect the VCR to a personal computer or similar device By connecting through the JLIP terminals you can control the VCR during editing and certain other operations from the connected personal computer or similar device When connecting this VCR to another device using the JLIP terminals each device must have a different JLIP ID number The JLIP ID number of this VCR is preset to 1 when shipped from the factory You can change this number to any other number between 1 to 99 NOTE For further details on the JLIP system or devices consult your nearest JVC dealer EE Access Main Menu screen then Initial Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt VI Access JLIP ID Number Set screen Press AV to move the highlight bar arrow to JLIP ID NO SET
76. k EJ Start recording On the VCR Press REC On the Remote While holding REC 6 press PLAY P e If you are using a Master Edit Control equipped JVC camcorder recording starts automatically on this VCR Refer to camcorder s instruction manual NOTE Be sure to select AUTO for PICTURE CONTROL or NORM when VIDEO CALIBRATION is set to OFF after you finish dubbing the tapes pg 20 o Editing with Another VCR You can use your VCR as the playback or recording VCR Refer also to the other components instruction manuals for connection and its operations EE Make connections Example 1 When another VCR is VHS VCR Connect two VCRs with the supplied audio video cable This VCR To AUDIO VIDEO IN To AUDIO VIDEO OUT When using this VCR as the recording VCR connect this VCR s AUDIO VIDEO IN connectors to the When using this VCR as the playback VCR connect this VCR s AUDIO VIDEO OUT connectors to the audio video output connectors on another VCR audio video input connectors on another VCR U U U tid e f another VCR is monaural connect this VCR s AUDIO L IN or OUT connector to the audio output or input connector on another VCR To audio video output To audio video input Example 2 When another VCR is S VHS VCR and when using this VCR as the playback VCR This VCR for playback To AUDIO OUT 1 1 1 To S VIDEO OUT 1 AL 7 S
77. ly in U S A LIMITED WARRANTYCcONSUMER VIDEO 1 90 JVC COMPANY OF AMERICA warrants this product and all parts thereof except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below The Warranty Period PARTS LABOR lyr 90pays THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY 50 UNITED STATES THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO WHAT WE WILL DO If this product is found to be defective JVC will repair or replace defective parts at no charge to the original owner Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers Parts used for replacement are warranted only for the remainder of the Warranty Period All products and parts thereof may be brought to a JVC authorized service center on a carry in basis except for Television sets having a screen size 25 inches and above which are covered on an in home basis WHAT YOU MUST DO FOR WARRANTY SERVICE Return your product to a JVC authorized service center with a copy of your bill of sale For your nearest JVC authorized service center please call toll free 800 537 5722 If service is not available locally box the product carefully preferably in the original carton and ship insured with a copy of your bill of sale plus a letter of explanation of the problem to the
78. mum operating distance of the remote control is about 8 m NOTE If the Remote does not work properly remove its batteries wait for a few seconds replace the batteries and then try again Video heads cleaning The heads get dirty in the following cases e in an environment prone to extreme temperature or humidity e in a dusty environment e flaw dirt or mold on video tapes e continuous usage for a long time Use a dry cleaning cassette TCL 2 when e Rough poor picture appears while a tape is played back e The picture is unclear or no picture appears USE CLEANING CASSETTE appears on the screen only with SUPERIMPOSE set to ON C pg 20 ATTENTION To mobile phone users Using a mobile phone in the vicinity of the VCR may cause picture vibration on the TV screen or change the screen to a blue back display On placing the VCR Some TVs or other appliances generates strong magnetic fields Do not place such appliance on top of the VCR as it may cause picture disturbance i Index Front Panel O REC LINK button SP EP button Cassette loading slot A Audio DUB button REC button PAUSE HM button 24HR QUICK PROGRAM button PLAY button ADVANCED JOG dial S VIDEO input connector AUDIO VIDEO input connectors DIGITAL TBC NR lamp DIGITAL TBC NR button POWER button
79. nd TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR Preparations EE Access Main Menu screen then Initial Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt MAIN MENU FUNCTION SET TUNER SET INITIAL SET REC LEVEL CTL VIDEO NAVIGATION PRESS a v THEN OK PRESS MENU TO END VI Access Clock Set screen Press AV to move the highlight bar arrow to CLOCK SET then press OK or ee INITIAL SET CLOCK SET LANGUAGE ENGLISH GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET JLIP ID NO SET SELECT WITH 4 AND OK PRESS MENU TO END Setting clock semiautomatically Semiauto Clock Set You can change the host channel D S T Daylight Saving Time time zone setting manually First follow steps fl to M in Preparations above then go to the following steps NOTE The time set previously will be erased when AUTO CLOCK HOST CH D S T or TIME ZONE setting is changed E Set Auto Clock to ON CLOCK SET Press OK or gt on the Remote repeatedly to TIME am CATE YEAR move the highlight bar to AUTO CLOCK AUTO CLOCK ON A HOSTCH AUTO CATV then press AV so that ON is selected DSTO auto COY TIME ZONE AUTO PRESS a v THEN OK PRESS MENU TO END VI Select host channel You can either select AUTO
80. nual Clock Set pg 7 PRO N Z During Initial Auto Clock Set Auko Auto blinks A N During Auto Channel Set The channel numbers are displayed as they are scanned and set Plug amp Play Completed The current time is displayed What to do if Plug amp Play setting failed e If an incorrect time is displayed on the display panel perform the procedure in Semiauto Clock Set pg 7 or Manual Clock Set F pg 7 f appears on the display panel ensure that the antenna cable is connected correctly Then turn on and off the VCR the Plug amp Play setting will be automatically reactivated If Plug amp Play setting is not performed though the antenna cable is connected correctly perform the procedure in Manual Clock Set C pg 7 and Auto Channel Set gt pg 8 or Manual Channel Set pg 8 EJ Set VCR channel The VCR channel is the channel on which you can watch the picture from the VCR on the TV when using the RF connection Press POWER to turn off the VCR then press STOP EJECT W amp on the VCR for more than 5 seconds 3CH appears on the display panel Press CH to select 3CH 4CH or CH OFF then press OK e The VCR channel is preset to 3CH Set to 4CH if 3CH is used for broadcasting in your area EJ Final preparation for use Turn on the VCR and the TV and select the VCR channel 3 or 4 or A
81. objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way When the product exhibits a distinct change in performance this indicates a need for service 3 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or which have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 4 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operating condition Th How to use the Remote Before use insert two AA size batteries into the Remote with the polarity and matched correctly as indicated on the battery compartment or on the lid The Remote can operate most of your VCR s functions as well as basic functions of TV sets cable boxes and DBS receivers e Point the Remote toward the remote sensor on the target component e The maxi
82. ough all the code numbers listed for your model of cable box then try all the other numbers For DBS receiver DBS RECEIVER BRAND SET e If the DBS receiver s channel changes to i the channel listed below for your brand DID YOUR DBS RECEIVER setting is complete Press OK or D ec 1007 JVC gt 100 SONY 205 NO PRESS A w THEN OK PRESS MENU TO END ECHOSTAR 100 RCA 205 e If the DBS receiver s channel does not change as shown above Press AV to move the highlight bar arrow to NO then press OK or b Repeat step I PO Playback Basic Playback e Turn on the VCR and TV and select the VCR channel or AV mode Set the VCR TV CABLE DBS selector on the Remote to VCR EF Load a cassette Make sure the window side is up the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR e Do not apply too much pressure when inserting e The VCR turns on automatically e The tape will run for a few seconds while the VCR searches for the tape number e f the cassette s record safety tab has been removed playback begins automatically NOTE When you use the Video Navigation function operate the VCR only after the tape number is detected otherwise you cannot use the Video Navigation function PA Start playback Press PLAY P e The S VHS indicator lights up when you play back a tape recorded
83. our cable box or DBS receiver refer to its instruction manual e Turn on the VCR and TV and select the VCR channel or AV mode e Set the VCR TV CABLE DBS selector on the Remote to VCR E Situate Controller If both a cable box and a DBS receiver are used position the Controller so its signal reaches the remote sensors on both the cable box and DBS receiver VI Attach Controller Fix securely using the adhesive strip attached on the back of the Controller Cable box or DBS receiver Controller suggested locations RF output Audio video output Transmitter Controller To ANTENNA IN To AUDIO VIDEO IN e f your cable box or DBS receiver does not have audio video output connectors connect the RF output terminal on the unit to the ANTENNA IN terminal on the rear of your VCR e f your cable box or DBS receiver has audio video output connectors connect an audio video cable between the AUDIO VIDEO IN connectors on the rear of the VCR and the audio video output connectors on the unit e f both a cable box and a DBS receiver are used it is recommended that you connect the DBS receiver to your VCR s AUDIO VIDEO IN connectors and the cable box to your VCR s ANTENNA IN connector 6 a Pl Connect Controller to VCR Connect the Controller to the CABLE BOX Controller connector on the rear panel EJ Turn on cable box or DBS receiver Select a channel other than channel 9 on your cable box or channel
84. pped 75 ohms unbalanced Quartz 1 year programmable timer 8 programs Approx 3 min Infrared remote control unit AA battery x 2 Audio video cable RF cable F type S video cable 4 pin Controller Specifications shown are for SP mode unless specified otherwise E amp O E Design and specifications subject to change without notice et ee Troubleshooting Before reguesting service use this chartand see if you can repair the trouble yourself Small problems are often easily corrected and this can save you from the trouble of sending your VCR off for repair Power SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION The power will not come The AC power cord is disconnected e Connect the AC power cord on e The Child Lock function is activated Press and hold POWER for more than 10 seconds to release the Child Lock function pg 21 The clock works but the The VCR is in the timer recording standby mode Press TIMER to disengage the timer VCR s power will not come with AUTO TIMER set to OFF F pg 20 on e The Child Lock function is activated Press and hold POWER for more than 10 seconds to release the Child Lock function pg 21 The Remote will not e The batteries are discharged e Replace batteries function e The VCR is in the timer recording standby mode Press TIMER to disengage the timer e Remote control A B code is wrong e Reset A B code I
85. ring to return to still picture Press PLAY to resume normal playback e If you press and hold REW 444 or FF gt for more than 2 seconds simply releasing it cancels the picture search and normal playback resumes Slow Motion Press JOG SHUTTLE so that the button lights up Press PAUSE II to pause then turn the SHIUTTLE ring to the right for forward slow motion or to the left for reverse slow motion Release the SHUTTLE ring to return to still picture Press PLAY to resume normal playback e During still picture press and hold BI to start forward or dd to start reverse slow motion playback When you release the button still picture resumes e During still picture holding PAUSE ll for more than 2 seconds also starts forward slow motion playback If you press PAUSE IB again still picture resumes NOTE During slow motion some noise may appear on the TV screen Press CH to eliminate the noise Variable Speed Picture Search Press IM or P OR During playback or still repeatedly press JOG SHUTTLE so that the button lights up Turn the SHUTTLE ring to the right for forward variable speed search or to the left for reverse variable speed search Release the SHUTTLE ring to return to still picture Press PLAY to resume normal playback e Each time you press Md or BPI the playback speed changes To decrease the speed during picture search press the opposite direction button repeatedly
86. s 100 205 on your DBS receiver EJ Access Main Menu screen then Initial Set screen on VCR Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt Access Cable Box Set screen or DBS Receiver Set screen Press AV to move the highlight bar arrow to CABLE BOX SET or DBS RECEIVER SET then press OK or D INITIAL SET CLOCK SET LANGUAGE ENGLISH GUIDE CHANNEL SET gt CABLE BOX SET DBS RECEIVER SET JLIP ID NO SET SELECT WITH 4 AND OK PRESS MENU TO END EJ Select output channel Your selection depends on how the unit is connected to your VCR e If the unit is connected to your VCR s ANTENNA IN terminal on the rear panel Press AV until the channel number representing the cable box s output CH2 CH9 or DBS receiver s output CH3 or CH4 appears on the screen e If the unit is connected to your VCR s AUDIO VIDEO IN connectors on the front panel press AV until ON F 1 FRONT appears on the screen e If the unit is connected to your VCR s AUDIO VIDEO IN CABLE BOX SET gt 4 PRESS Aw THEN OK PRESS MENU TO END connectors on the rear panel press AV until ON L 1 REAR appears on the screen e If you do not use any unit press AV until OFF appears on the screen EJ Access Brand Set screen Press OK or b e If the Clock Set screen appears perform Manual Clock Set C pg 7 If you press ME
87. tegory changes as follows lt gt CATEGORY lt gt MOVIE gt SPORTS lt gt SPECIAL gt SERIES lt gt NEWS lt gt CHILDREN lt gt SHOPPING gt back to the beginning Press MENU to return to normal screen SO 0114 JVC NEWS 1 3 8 00PM 2 27 02 CH 5 10 00PM 2 28 02 CH 16 gt 8 15AM 1 15 02 CH 99 8 15A gt 10 45A 2 30 EP GO 0114 JVC NEWS 1 3 8 00PM 2 27 02 CH 5 10 00PM 2 28 02 CH 16 gt 8 15AM 1 15 02 CH 99 8 15A 10 45A 2 30 EP WORLD CUP 02 SPORTS PRESS 4a V THEN OK TO EDIT OR CANCEL TO DELETE PRESS MENU TO END Deleting tape information First follow steps fl to Ml in Preparations above then go to the following steps NOTE The tape information for the Video Navigation is deleted but the actual recorded programs will not be erased E Select tape title Press AV to move the highlight bar arrow to the tape title then press CANCEL 50 0114 3 18 02 1 3 8 00PM 2 27 02 CH 5 10 00PM 2 28 02 CH 16 8 15AM 1 15 02 CH 99 PRESS a v THEN OK TO EDIT OR CANCEL TO DELETE PRESS MENU TO END FA Delete tape information Press AV to move the highlight bar pore re gt DELETE arrow to YES then press OK or bas Press MENU to return to normal screen EATN PRESS a v THEN OK PRESS MENU TO END Deleting program information First follow steps fl to Ml in Preparations above then go to the following steps NOTE The program
88. try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug B Your product may be equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 2 Power Sources Operate your product only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company If your product is intended to operate from battery power or other sources refer to the operating instructions 3 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 4 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product 5 Ventilation Slots and openings in the cabinet are provided for ventilation To ensure reliable operation of the product and to protect it from overhe
89. tting CF pg 14 work properly previous area Video Navigation SYMPTOM Title screen does not appear for the currently inserted tape The VCR cannot search for the correct program MEMORY FULL appears on the screen when you try to start recording Other Problems SYMPTOM The channel cannot be changed Even though Auto or Semiauto Clock Set has been performed the clock is Incorrect POSSIBLE CAUSE e The current inserted tape has not been recorded on this VCR e Two or more tape numbers are recorded on one tape e The VCR s memory for Video Navigation is full POSSIBLE CAUSE e Recording is in progress e The clock setting data received from the host channel is incorrect a ee CORRECTIVE ACTION e Tape information cannot be shown if it has not been recorded on this VCR e Video Navigation cannot work correctly on a tape if it has more than one tape number If this happens fast forward the tape up to its end eject it and try it again e Check the remaining memory C pg 18 If it is full delete unnecessary Video Navigation information lt pg 17 CORRECTIVE ACTION Press PAUSE ll to pause the recording change channels then press PLAY BR to resume recording e Select a different host channel during Semiauto Clock Set pg 7 or perform Manual Clock Set F pg 7 FOR SERVICING Only in U S A HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE
90. video cable supplied Audio cable not supplied U U To audio input J J J To S video input Another VCR for recording Example 3 When another VCR is S VHS VCR and when using this VCR as the recording VCR This VCR for recording To AUDIO input Tt Tt Tt To S VIDEO input Audio cable not supplied S video cable supplied U U To audio output J J J To S video output Another VCR for playback VI Load cassettes Insert the playback cassette into the playback VCR and the cassette to be recorded on into the recording VCR EJ Select input location on recording VCR Select the correct external input location on the recording VCR On this VCR when using this VCR as the recording VCR Select L 1 when connecting the other VCR to the audio video or S video input connectors on the rear panel Select F 1 when connecting the other VCR to the audio video or S video input connectors on the front panel On the VCR Press CH or push the ADVANCED JOG dial then turn it to the left or right until L 1 or F 1 appears on the display panel On the Remote Press AUX and or CH until L 1 or F 1 appears on the display panel El Select video input connector on recording VCR When using this VCR as the recording VCR select the appropriate mode depending on the connector being used F pg 21 When using S VIDEO input connector on the front panel set FRONT AUX I
Download Pdf Manuals
Related Search
Related Contents
FUNK-DURCHGANGSMELDER mit Alarmfunktion - XXL Neff K4664 Top Freezer Refrigerator 『エジソンのお著聞取扱説明書 Noctua NH-U12F VGN-AR500 Series - Manuals, Specs & Warranty E-Flow viersprachig Copyright © All rights reserved.
Failed to retrieve file