Panasonic CT-13R28W 13" TV
Contents
1. CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE S ig ANTENNA LEAD IN WIRE ANTENNA I DISCHARGE UNIT d NEC SECTION 810 20 ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE S2898A Before using the remote control transmitter batteries must first be installed HOW TO INSTALL BATTERIES Slide the battery compartment cover 1 3 Replace the battery compartment cover Use two AA size penlight batteries supplied for the transmitter The batteries may last approximately one year depending on how much the remote control is used For best performance it is recommended that batteries should be replaced on a yearly basis or when the remote operation becomes erratic Do not mix old and new batteries or different types BATTERY PRECAUTIONS These precautions should be followed when using batteries in this device 1 Use only the size and type of batteries specified 2 Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Revers2. by products not supplied by the warrantor or failures which result from accidents misuse abuse neglect mishandling misapplication alteration faulty installation set up adjustments misadjustment of consumer controls improper maintenance power line surge lightning damage modification or commercial use such as in a hotel office restaurant or other business rental use of the product service by anyone other than a Factory Servicenter or other Authorized Servicer or damage that is attributable to acts of God THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER LIMITED WARRANTY COVERAGE THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY As examples this excludes damages for lost time cost of having someone remove or re install an installed unit if applicable or travel to and from the servicer The items listed are not exclusive but are for illustration only ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the exclusions may not apply to you This warranty gives you specific legal rights and you may also have others rights which vary from state to state If a problem with this product develo
3. cord is plugged in e No broadcast on station tuned e Timer is set e Power interrupted TV station experiencing problems or program tuned is not closed captioned Try another channel e Check CATV connection or VHF UHF antenna reposition or rotate antenna e Select the Closed caption e Select proper language in the SET UP mode TV does not operate Poor sound or No sound Poor picture or No picture Poor reception on some channels Poor color or no color Picture wobbles or drifts No CATV reception Horizontal or diagonal bars on screen No reception above channel 13 No Remote operation TV shuts off Cannot see closed caption Display is not shown in your language SPECIFICATIONS gt lt COLOR more vibrant color reduces color TINT greenish hue reddish hue BRIGHTNESS increase brightness decrease brightness PICTURE increase contrast decrease contrast SHARPNESS makes picture makes picture softer TO RETURN TO INITIAL SETTING Select the NORMAL then select SET as in step2 AC Power Input AC Power Consumption Chassis Construction Picture Tube Horizontal resolution Audio Power Output Rating Speaker Tuner Type Remote Control Receiving Channels Antenna Input Impedance Input Dimensions Weight 120V 60Hz 54 Watts IC Solid state 13 measured diagonally 260 lines 1 0 Wat
4. enclosure that may be of sufficient magnitude to constitute a risk of electric shock CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE MPORTANT SAFEGUARDS 1 READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated RETAIN INSTRUCTIONS The safety and operating instructions should be retained for 9 future reference HEED WARNINGS AIl warnings on the unit and in the operating instructions should be adhered to FOLLOW INSTRUCTIONS All operating and use instructions should be followed CLEANING Unplug this unit from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning the exterior cabinet only ATTACHMENTS The manufacturer of this unit does not make any recommendations for attachments as they may cause hazards WATER AND MOISTURE Do not use this unit near water For example near a bathtub washbowIl kitchen sink laundry tub in a we
5. For channels 10 and above press the 2 digits in order CATV mode direct channel selection When the TV CATV menu option is in the CATV position channels can be selected as follows 1 9 Press 0 twice then 1 9 as needed Example to select channel 2 press 002 10 12 Press 0 then remaining 2 digits Example to select channel 12 press 012 13 99 Press the 2 digits in order Example to select channel 36 press 36 100 125 Press the 3 digits in order Example to select channel 120 press 120 NOTE If the station being viewed stops broadcasting the TV will automatically shut off after 15 minutes CLOSED CAPTION WHAT IS CLOSED CAPTIONING This television has the capability to decode and display Closed Captioned television programs Closed Captioning will display text on the screen for hearing impaired viewers or it will translate and display text in another language TO VIEW CLOSED CAPTIONS Press ACTION and press lt to select the SET UP mode then press ACTION OFF Press A to select CC mode and then press then press A or Y CAPTION CH2 to select desired Closed Caption e g CAPTION CH1 then press ACTION Press ACTION twice Captions This Closed Caption Mode will display text on the screen in English or another language depending on the setting of the Closed Captions Generally Closed Captions in English are transmitted on Captions Channel 1 and Closed Captions in other languages are transmi
6. If you connect the TV to a VCR camcorder or TV game through the audio video in jacks use the TV VIDEO to make your selection 2 To connect the TV to a TV Game The TV can also be used as a display device for many video games However due to the wide variety of different types of signal generated by these devices and subsequent hook up variations required they have not all been included in the suggested connection diagrams You ll need to consult each component s Owner s Manual for additional information Press the TV VIDEO repeatedly to select the desired mode AUX will display on the screen for 4 seconds AUX To Audio Video OUT Front of TV TV GAME 3 To connect the TV to a camcorder To playback from the camcorder connect the 1 To connect the TV to a VCR VCR Front of TV camcorder to the TV as shown Ss To AV OUT Front of TV 00 CED eek ah a t t To Audio ae Video OUT VIDEO AUDIO not supplied TROUBLESHOOTING GUIDE Before requesting service please refer to the following chart for the symptom and possible solution SYMPTOMS POSSIBLE SOLUTIONS Make sure the power cord is plugged in e Try another AC outlet e Power is off check fuse or circuit breaker Unplug unit for an hour then plug it back in e Station or CATV experiencing problems tune to another station e Check sound adjustments VOLUME and MUTE e Check for sources of possible interference e Statio
7. O PROGRAM MANUAL PROGRAM cc OFF A gt ACTION AUTOMATIC CHANNEL MEMORY 1 Press ACTION and press lt to select the SET UP mode then press SETUP ACTION LANGUAGEDIOMAILANGUE AUTO PROGRAM MANUAL PROGRAM Press W twice to select AUTO PROGRAM mode and then press P m mad 4 ACTION The TV will begin memorizing all the channels available in your area Press ACTION twice MANUAL CHANNEL MEMORY Press ACTION and press lt to select the SET UP mode then press ACTION SETUP LANGUAGE IDIOMA LANGUE Mi CABLE AUTO PROGRAM Press A twice to select MANUAL PROGRAM mode and then press EINVAL PROGRAM lt amp gt ACTION Select the desired channels to be added or deleted using Direct Channel Selection 10 keys 0 9 CH A or V Press lt or to select ADD or DELETE If an unmemorized channel was selected step 3 the channel indicator will be yellow Press lt or if you wish to ADD the unmemorized channel The channel indicator will change from yellow to blue when a channel is added and the channel will be memorized If a memorized channel was selected step 3 the channel indicator will be blue Press lt or if you wish to DELETE the channel from memory The channel indicator will change from blue to yellow when a channel is deleted Repeat Steps 3 and 4 for each channel to be added or deleted Press ACTION three times SETTING TIMER You can set the TV to turn off after a pres
8. PANASONIC CONSUMER ELECTRONICS COMPANY PANASONIC SALES COMPANY DIVISION OF DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA MATSUSHITA ELECTRIC OF PUERTO RICO One Panasonic Way INC Ave 65 de Infanteria Km 9 5 Secaucus New Jersey 07094 San Gabriel Industrial Park Carolina Puerto Rico 00985 Panasonic Color Television Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship Panasonic Consumer Electronics Company or Panasonic Sales Company collectively referred to as the warrantor will for the length of the period indicated on the chart below which starts with the date of original purchase warranty period at its option either a repair your product with new or refurbished parts or b replace it with a new or a refurbished product The decision to repair or replace will be made by the warrantor TV CATEGORIES ALL PARTS EXCEPT CRT LABOR CRT SERVICE 9 21 diagonal 1 ONE YEAR 90 DAYS 2 TWO YEARS CARRY IN During the Labor warranty period there will be no charge for labor During the Parts warranty period there will be no charge for parts You must carry in your product or arrange for in home service in home service available only for 22 diagonal and larger screen as applicable during the warranty period If non rechargeable batteries are included they are not warranted This warranty only applies to products purchased and se
9. d Captioned signal e If using an indoor antenna or if TV reception is very poor the Closed Caption Decoder may not appear or may appear with strange characters or misspelled words In this case adjust the antenna for better reception or use an outdoor antenna SETTING LOCK This TV is fitted with a V CHIP controller which provides you with channel viewing access controls and restrictions This function allows adult screening of TV programs based upon ratings Press ACTION Press W to select the LOCK mode then press ACTION SME Enter your password 4 digits using Direct channel selection 0 9 In the event of entering an incorrect password press lt or wait a few seconds to delete the wrong password Enter the same password for confirmation only for the first time Press A or W to select the V CHIP option then press gt Press lt or gt to select the ON then press ACTION fe A Press A or W to select the TV RATING or MOVIE RATING option then press gt Press lt or gt to select the desired rating for the applicable video or TV channel then press ACTION lt lt gt gt gt TV RATING OFF lt gt TV Y lt gt TV Y7 lt gt TV G lt gt TV PG lt gt TV 14 lt gt TV MA O fe TV Y all children TV PG parental guidance TV Y7 7 years old and above TV 14 14 years old and above TV G _ children s program TV MA 17 years old and above When you select TV Y7 TV PG TV 14 or TV MA pre
10. ed batteries may cause damage to the device 3 Do not mix different types of batteries together e g Alkaline and Carbon zinc or old batteries with fresh ones 4 If the device is not to be used for a long period of time remove the batteries to prevent damage or injury from possible battery leakage 5 Do not try to recharge batteries not intended to be recharged they can overheat and rupture Follow battery manufacturer s directions POWER SOURCE TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet NOTES 1 Never connect the AC line cord plug to other than AC outlet Wider Hole and Blade power cord only 2 If the polarized AC cord does not fit into a non polarized AC outlet do not attempt to file or cut the blade It is the user s responsibility to have an electrician replace the obsolete outlet 3 If you cause a static discharge when touching the unit and the unit fails to function simply unplug the Polarized AC Cord Plug One blade is wider than the other the specified voltage 120V 60Hz Use the attached unit from the AC outlet wait a few minutes and plug it back in The unit should return to normal operation information for On Screen operations Remote control Part No EUR7713020 13R18B 13R38S EUR7713030 13R28W POWER Press to turn t
11. et amount time 0 9 4 4 ACTION Press ACTION and press to select the TIMER mode then press ACTION Press and then press lt or gt to select desired time then press ACTION lt gt ACTION After the timer is programmed the display will disappear then reappear momentarily every ten minutes to remind you the timer function is operating To confirm the timer setting repeat step 1 The remaining time will be displayed To cancel the timer setting select the OFF ADJUSTING PICTURE You can adjust the settings for color sharpness contrast brightness and tint Press ACTION twice to select the PICTURE mode Press A or to select desired picture then press P Press lt or gt to adjust the setting CONNECTION TO OTHER EQUIPMENT The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features of each component Check the Owner s Manual provided with each component for the location of video and audio inputs and outputs The connection diagrams below are offered as suggestions You may need to modify them to accommodate your particular assortment of components The diagrams are intended to show component video and audio interconnections only Press the TV VIDEO to select the AV mode to use the TV as a monitor Operate your VCR as usual NOTE TV VIDEO only exists in the remote control TV AV SELECTION
12. ext will not be affected by the language selection TV OPERATION To turn on the TV press POWER The VOLUME can be adjusted to a desired level by pressing VOL VOLUME lt or gt The sound level will be indicated on the TV screen by GREEN BARS AND A NUMBER As the sound level increases so do the number of BARS AND THE NUMBER on the screen The same is true for decreasing the level Set the TV CATV menu option to the appropriate position When shipped from the factory this menu option is in the CATV setting See To Memorize Channels TV VHF UHF channels CABLE CABLE TV channels CH CHANNEL A and V Press and release the CH CHANNEL A or W The channel automatically stops at the next channel set into memory Press and hold the button down to change channels more quickly For proper operation before selecting channels they should be set into the TV s memory See To Memorize Channels DIRECT CHANNEL SELECTION 0 9 Press these buttons to select a channel The channel number will appear on the upper right corner of the TV screen If an invalid channel number is selected the display will revert to the previous channel TV MODE DIRECT CHANNEL SELECTION When the TV CATV menu option is in the TV position all channels can be instantly selected by using two buttons For example to select channel 2 press 0 then 2 If you press only 2 channel selection will be delayed for a few seconds
13. ght or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock OBJECT AND LIQUID ENTRY Do not push objects through any openings in this unit as they may touch dangerous voltage points or short out parts that could result in fire or electric shock Never spill or spray any type of liquid into the unit OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is con nected to the unit be sure the antenna or cable system is grounded to provide some protection against voltage surges and built up static charges Section 810 of the National Electrical Code ANSI NFPA 70 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connec tion to grounding electrodes and require ments for the grounding electrode SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel DAMAGE REQUIRING SERVICE Unplug this unit from the wall outlet and refer servicing to qua
14. he TV on Press again to turn the TV off ACTION Press to display the On screen menu function And also press to enter or select VOL VOLUME 4 gt Press P to increase or to decrease the volume level And also press to select the desired setting during On Screen operations MUTE To turn off the sound press this button once The TV will be silenced and the symbol MUTE will appear on the screen The muting feature can be released by pressing MUTE again or one of the VOL lt q or P Direct Channel Selection 0 9 Allows direct access to any channel R TUNE This button allows you to go back to the previous channel selected by just pressing R TUNE Press this button again to return to the channel you were watching CH CHANNEL A V Press A to change to a higher numbered channel set into memory Press W to change to a lower numbered channel set into memory And also press to select the desired setting during On Screen operations TV VIDEO Switches between TV and external input RECALL When you press this button the channel number will appear in the upper right corner of the screen Press the button again to remove display from the screen LOCATION OF CONTROLS joo 0000 C9 T 1 EPJ Earphone Jack Plug an earphone or monaural headphones with an 1 8 miniplug into this jack for private listening 2 Remote Sensor Signals from the Re
15. lified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the unit c Ifthe unit has been exposed to rain or water 20 22 23 d If the unit does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation e If the unit has been dropped or the cabinet has been damaged f When the unit exhibits a distinct change in performance this indicates a need for service REPLACEMENT PARTS When replacement parts are required be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 21 SAFETY CHECK Upon completion of any service or repairs to this unit ask the service technician to perform safety checks to determine that the unit is in proper operating condition HEAT The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the
16. mote Control unit are received here 3 POWER Press to turn the TV on or off 4 VOLUME lt gt Press to raise or lower the level of the sound And also press to select the desired setting during On Screen operations ACTION Press to display the On screen menu function And also press to enter or select information for On Screen operations 5 CHANNEL A F Press to select a higher or lower numbered channel set into memory And also press to select the desired setting during On Screen operations 6 AUDIO VIDEO IN Jacks Audio and video signal cables from an external source can be connected here NOTE If needed customer can enter the OSD by pressing VOLUME lt and gt of the front panel at the same time SETTING LANGUAGE This TV can display the channel number on screen displays and picture adjustments on the screen in English Spanish or French Press ACTION 2 e Press lt to select the SET UP mode then press ACTION 4 io S NOTE SURETDE All four arrows can be used to select the SET UP mode not just lt 4 TG PROGRAM A P ACTION Press gt and then press A or to select desired language e g English then press ACTION neal Press ACTION to select the EXIT mode then press FRANCAIS ACTION again al V ACTION NOTE If Spanish or French is chosen the Closed Caption indicators will be in the selected language but the Closed Caption t
17. n or CATV experiencing problems tune to another station Make sure channels are set into memory e Check antenna or CATV connections adjust antenna e Check for sources of possible interference e Check picture control adjustments Station or CATV experiencing problems tune to another station Make sure channels are set into memory e Station is weak adjust antenna to receive desired station e Check for sources of possible interference e Station or CATV experiencing problems tune to another station Make sure channels are set into memory e Check picture control adjustments e Check antenna or CATV connections adjust antenna e Check for sources of possible interference e Station or CATV experiencing problems tune to another station Make sure channels are set into memory e CATV company is scrambling signal e Adjust antenna e Check all CATV connections e Set TV CATV menu option to the CATV mode e Station or CATV system problems try another station e Check antenna connections adjust or re direct antenna e Check for sources of possible interference e Make sure TV CATV menu option is in the appropriate mode If using antenna check UHF antenna connections Batteries are weak dead or inserted incorrectly Remote is out of range move closer to TV within 15 feet Make sure Remote is aimed at sensor e Confirm there are no obstructions between the Remote and the TV Make sure the power
18. nic Services Company 20421 84th Avenue South Kent WA 98032 6 am to 5 pm Monday Friday 6 am to 10 30 am Saturday PST Visa MasterCard Discover Card American Express Check Service in Puerto Rico Matsushita Electric of Puerto Rico Inc Panasonic Sales Company Factory Servicenter Ave 65 de Infanteria Km 9 5 San Gabriel Industrial Park Carolina Puerto Rico 00985 Phone 787 750 4300 Fax 787 768 2910 03 07 J3M11001B ANTENNA CATV CONNECTIONS ANTENNA CONNECTIONS Connect the antenna to the antenna jack from Antenna Single 75 ohm cable LEE HI 300 ohm twin lead wire e O 300 75 OHM MATCHING TRANSFORMER not supplied 300 ohm twin lead wire E l gt Single 75 ohm cable COMBINER not supplied Back of TV CATV CONNECTIONS Incoming CATV Converter Descrambler m E 1 This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box Some cable companies offer premium pay channels in which the signal is scrambled Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels If you subscribe
19. ower outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug still fails to fit contact your electri cian to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug If your unit is equipped with a 3 wire grounding type plug a plug having a third grounding pin this plug will only fit into a grounding type power outlet This too is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 10 PORTABLE CART WARNING symbol provided by RETAC 83126A REMOTE CONTROL 12 13 14 15 16 17 18 19 POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance LIGHTNING To protect your unit during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the unit due to lightning and power line surges POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric li
20. ps during or after the warranty period you may contact your dealer or Servicenter If the problem is not handled to your satisfaction then write to the warrantor s Consumer Affairs Department at the addresses listed for the warrantor PARTS AND SERVICE INCLUDING COST OF AN IN HOME SERVICE CALL WHERE APPLICABLE WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY J3M11001B U Printed in Thailand OWNER S MANUAL Panasonic COLOR TELEVISION CT 13R18B CT 13R28W CT 13R38S CAUTION Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user s authority to operate this equipment ATTENTION If you purchase a universal remote control from your local retailer please contact the remote manu facturer for the required programming code TV CATV MODE SELECTION When shipped from the factory the TV CATV menu option is set to the CATV Cable Television mode If not using CATV set this menu option to TV mode For Product Information Operating Assistance Literature Request Dealer Locations and all Customer Service inquiries please contact 1 800 211 PANA 7262 Monday Friday 9am 9pm Saturday Sunday 10am 7pm EST Web Site http www panasonic com You can purchase parts accessories or locate your nearest servicenter by visiting our Web Site Accessory Purchases 1 800 332 5368 Customer Orders Only Panaso
21. rviced in the United States or Puerto Rico This warranty is extended only to the original purchaser of a new product which was not sold as is A purchase receipt or other proof of the original purchase date is required for warranty service Carry in or In Home Service For Carry In or In Home Service as applicable in the United States call 1 800 21 1 PANA 7262 or visit Panasonic Web Site http www panasonic com For assistance in Puerto Rico call Panasonic Sales Company 787 750 4300 or fax 787 768 2910 In Home service if applicable requires clear complete and easy access to the product by the authorized servicer and does not include removal or re installation of an installed product It is possible that certain in home repairs will not be completed in home but will require that the product or parts of the product be removed for shop diagnosis and or repair and then returned Limited Warranty Limits And Exclusions This warranty ONLY COVERS failures due to defects in materials or workmanship and DOES NOT COVER normal wear and tear or cosmetic damage nor does it cover markings or retained images on the picture tube resulting from viewing fixed images including among other things letterbox pictures on standard 4 3 screen TV s or non expanded standard 4 3 pictures on wide screen TV s or onscreen data in a stationary and fixed location The warranty ALSO DOES NOT COVER damages which occurred in shipment or failures which are caused
22. ss RECALL to explain the rating Press A or W to select the desired rating you want Press to select the setting ON or OFF then press ACTION MOVIE RATING lt q lt gt P OFF lt gt G lt gt PG lt gt PG 13 lt gt R lt NC 17 lt gt X es G all ages R Parental guidance for under 17 PG parental guidance years old PG 13 parental guidance NC 17 17 years old and above for under 13 years old X adult only Press ACTION twice NOTES e If you forget your password turn on the TV Reduce the volume to a minium level Press and hold VOLUME lt on the front of the TV and press the 0 button on the remote control simultaneously Select the LOCK mode then enter a new password e If you want to change the password follow steps 1 3 and select the CHANGE PASSWORD option then enter your new password e The V Chip function is activated only on programs and tapes that have the rating signal e Once you block a program using the V Chip function the blocked program cannot be watched based on the content of the show When the program starts the INPUT PASSWORD will appear on the screen When you want to release the V Chip temporarily enter the password If you change the channel or turn off the TV while the V Chip function was temporarily released the original setting will be resumed If you return to the channel you were watching you must re enter your password to temporarily release your V Chip function again e If
23. t basement or near a swimming pool ACCESSORIES Do not place this unit on an unstable cart stand tripod bracket or table The unit may fall causing serious injury and serious damage to the unit 11 8A An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn VENTILATION Slots and openings in the cabinet back or bottom are provided for ventilation to ensure reliable operation of the unit and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the unit on a bed sofa rug or other similar surface This unit should never be placed near or over a radiator or heat source This unit should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to POWER SOURCE This unit should be operated only from the type of power source indicated on the rating plate If you are not sure of the type of power supply to your home consult your appliance dealer or local power company For units intended to operate from battery power or other sources refer to the operating instructions GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the p
24. to a cable service in which basic cable channels are unscrambled and premium channels require the use of a converter descrambler box you may wish to use a two set signal splitter sometimes called a two set coupler and an A B switch box from the cable installer or an electronics supply store Follow the connections shown left With the switch in the B position you can directly tune Back of TV For Subscribers to Basic Cable TV Service For Subscribers to Scrambled Cable TV Service any nonscrambled channels on your TV With the switch in For basic cable service not requiring a converter If you subscribe to a cable service which requires the use of a the A position tune your TV to the output of the converter descrambler box connect the CATV 75 ohm coaxial converter descrambler box connect the incoming cable to the descrambler box usually channel 3 or 4 and use the box cable directly to the antenna jack on the back of the converter descrambler box and connect the output of the box to to tune scrambled channels television the antenna jack on the back of the television Follow the connections shown left Set the television to the output of the converter descrambler box usually channel 3 or 4 and use the converter descrambler box to select channels TQB2AA0490 1 The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s
25. ts 1 1 2 x2 1 2 Full Range 8 ohm 181 Channel Quartz PLL Frequency Synthesized Infrared Direct Access 2 x AA batteries not supplied VHF 2 13 UHF 14 69 CATV 1 125 75 Ohm VHF UHF CATV Coaxial Input Video 1 0 Vp p 75 ohm Audio 300 mV 47k ohm 14 1 8 W x 13 15 16 D x 13 1 4 H 20 9 Ibs
26. tted on Captions Channel 2 TEXT CH1 TEXT CH2 A V ACTION Text The Text Closed Caption Mode will usually fill 1 2 of full screen with a programming schedule or other information After selecting a Closed Caption Mode it will stay in effect until it is changed even if the channel is changed If the Captions signal is lost due to a commercial or a break in the signal the Captions will reappear when the signal is received again If the channels are changed the Captions will be delayed approximately 10 seconds For television programs broadcasting with Closed Captions look in your TV guide for the Closed Captions symbol CC e When activating the Closed Captioned Decoder there will be a short delay before the Closed Captioned text appears on the screen e Closed Captioned text is only displayed in locations where it is available If no caption signal is received no captions will appear but the television will remain in the Caption Mode e Misspellings or unusual characters may occasionally appear during Closed Captioning This is normal with Closed Captioning especially with live programs This is because during live programs captions are also entered live These transmissions do not allow time for editing e When Captions are being displayed on screen displays such as volume and mute may not be seen or may interfere with Closed Captions Some cable systems and copy protection systems may interfere with the Close
27. you are changing channels using a VCR or a cable box while the TV remains on channel 3 or 4 the V Chip operates differently When you enter your password to temporarily release the block on any channel you have completely disabled the V Chip function for all stations To reset the V Chip turn your TV off and back on e Some cable boxes are built with a delay feature in some cases it can take up to 10 seconds for a program to appear after the password has been input TO MEMORIZE CHANNELS This TV is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory skipping over unwanted channels Before selecting channels they must be programmed into the TV s memory In addition to normal VHF and UHF channels this TV can receive up to 113 Cable TV channels To use this TV with an antenna set the TV CATV menu option to the TV setting When shipped from the factory this menu option is in the CATV setting TO MEMORIZE CHANNELS cannot be selected if the AV mode is selected TV CATV SELECTION Press ACTION and press lt to select the SET UP mode then press ACTION Press W to select MODE mode and then press Then press lt or gt to select the TV or CABLE mode then press ACTION Press ACTION twice NOTE Contact your cable company to determine the type of cable system used in your area SET UP LANGUAGE IDIOMA LANGUE MODE TV CABLE AUT
Download Pdf Manuals
Related Search