Garmin Foretrex 101 Wrist Mount Gps
Contents
1. FROM is highlighted to select a waypoint from which to measure Use the arrow buttons to highlight the desired waypoint from the waypoint list Press ENTER to select the waypoint Press ENTER when the field to the right of TO is highlighted to select a waypoint to end the measurement Press ENTER when the field to the right of ESTIMATED SPEED is highlighted to enter an estimated speed The Edit Number Page is displayed to allow you to enter the speed Use the ENTER button and the UP and DOWN buttons to enter a new speed Highlight OK and press ENTER when finished The unit returns to the Measure Distance Page The total distance between the two points and the time needed to travel to the selected point is displayed at the bottom of the page Using the Navigation Page Main Pages The Navigation Page helps guide you to a destination When you are moving with no particular destination in mind the Navigation Page shows you your moving direction and pad Navigation Page When you are moving towards a specific destination navigating a course the Navigation Page displays the name of the location two data fields that display distance FINAL DIST to final destination and speed by default and a direction arrow in the compass ring To 14 07 navigate simply follow the arrow SPEED Navigation Page Options Navigation Page Press ENTER when the Navigation Page is displayed to access the Navigation Page Op Navigating to Hom2. works well for Waypoints Menu Page geocaching To mark a waypoint You may mark a waypoint one of two ways e Press and hold the ENTER MARK button eee The Mark Waypoint Page displays HOA4 47 AeT e Press PAGE to view the Main Menu Mark Waypoint Tage Select Waypoints and press ENTER Select CREATE NEW The Mark Waypoint Page displays Editing a Waypoint After you have marked a waypoint using on of the above methods the Mark Waypoint Page displays You can change elements of the waypoint from this page You can enter a new name select a new symbol and enter a new elevation and latitude longitude High light OK and press ENTER to save the waypoint You may also edit elements of an existing waypoint using the same methods The only difference is that you will be editing from the Waypoint Review Page instead of the Mark Waypoint Page 21 Main Menu Pages Waypoints Menu Page ELEN 1033 H 38 51 347 4094 41 927 HO9H H ns Changing the waypoint symbol EDIT WAYPOINT HAME USE ENTER BUTTOH TO EDIT UPOOWH BUTTONS TO SELECT Edit Waypoint Name Page 22 To change the symbol 1 D From the Main Menu Page press the UP or DOWN button to highlight MARK Press the ENTER button to display the Mark Waypoint Page Press the UP or DOWN button and highlight the symbol in the flag Press the ENTER button to display the list of waypoint symbols Use the UP and DOWN buttons to
3. Navigation Page 13 Navigation Page Options c cee 13 Trip Computer 14 Using the Trip Computet sssi l4 Trip Computer OPtOns essiens 14 Timer Palicis 15 Displaying the Timer Page 005 15 Setting the TIME iiieoo 15 Using the Timer Page cca ciureeseeontieas 17 Main Menu Pages 0 18 Main Menu Page 18 Main Menu Page Basics 00 0 seer 18 Waypoints Menu Page 19 Waypoints Menu Page sc eeeeeeneeee 19 Marking a Waypoint scsrisssisirsoriiiss pal Editing a Waypoint 21 Review Waypoint Page sesssccsecsissssiss 4 Projecting a WAY DOIN serseri 26 Hunting and Fishing Information 27 Sun and Moon Information 4 28 Tracks Menu Page 29 Using the Tracks Menu Page 29 Using he Track LOG seuroina 30 Pan OpUONS sisina 30 Using the Setup Track Page 2006 3l Usmo Saved TACKS ceca al Tack Page OPLOS oenesosseis oe Introduction Table of Contents il Introduction Table of Contents iv Routes Menu Page cccccececscscececseeeeseees 34 Using the Routes Menu Page a Canne a OWLS ienen 34 Using the Route Pagese 33 Deleting All ROWS usisani 36 KOME OC UD oaeee 37 Roue Set p OPUOMs eas 3 Editing a ROUE essperensseirene 38 Navigating 4 ROUTE ssoessiisicsiisasiisinss 40 Setup Menu Set Timer nsss 41 Using the Setup Mem ascacricesnis 4l S ARG speeettancetsteasccaanetcacemces 4l Setting the TIM sissies snsetovenoseanersve
4. Use the UP and DOWN arrows to highlight TRACKS and press ENTER to open the o SANE TRACK Tracks Menu Page m To clear the Track Log from the Tracks Menu Page 1 Press the PAGE button to access the Main Menu Press the ENTER button when TRACKS is highlighted to open the Tracks Menu Page ea 2 Highlight CLEAR TRACK and press ENTER Use the UP and DOWN arrows to highlight THE TRACK Lowe YES on the pop up window and press ENTER to clear the track log t CEs Clearing the Track Log 29 Main Menu Pages Tracks Menu Page TRACKS PPP ROUTES IF PAN amp TRACEBACK G SETUP TRACK SAVE TRACK Tracks Menu Page Panning the Track Log 30 Using the Track Log To use the track log select the PAN TRACK LOG option to show a pointer that moves along the track log when you press the UP or DOWN button To Pan the track log 1 Press the PAGE button to access the Main Menu 2 Use the UP and DOWN arrows to highlight TRACKS and press ENTER to open the Tracks Menu Page 3 Use the UP and DOWN arrows to highlight PAN amp TRACBACK and press ENTER 4 Use the UP and DOWN arrows to pan the track log Press ENTER to display the Pan Options TRACBACK GOTO MARK and ZOOM Pan Options After you have panned the track log using the UP and DOWN buttons press ENTER to display the Pan Options TracBack guides you to where you started by following the track
5. for easily maneuvering from one waypoint to the next With handy and convenient wrist strap design the power ful Foretrex 101 allows you to store up to 500 waypoints and 20 routes in the units mem ory while also providing built in WAAS capability In addition the Foretrex 101 boasts a customizable trip computer 10 000 track points as well as PanTrack and TracBack Getting Started With an optional PC Interface Cable you can connect your Foretrex 101 to your computer to transfer waypoints and routes between MapSource and your unit Refer to the MapSource User s Guide and MapSource Help File for complete information The images below describe the buttons and some features of your Foretrex 101 LCD Display Strap spring Back View without strap ane Front View with Backlight bars _ Antenna PC Interface Cable Connector under weather cap S tvv Battery Cover Serial Number Speaker POWER GOTO PAGE ENTER DOWN UP BACKLIGHT MARK Overview Using the Buttons Getting Started POWER GOTO PAGE ENTER DOWN UP MARK The POWER button e Press and hold to turn unit on and off e Press and release to turn display backlight on and off The GOTO button e Press to initiate a Goto navigate to a specific destination waypoint The PAGE button e Press to switch between the Main Pages e Press to back out or escape out of the present page or screen or Press to undo the most recent action
6. log that you left behind allowing you to return along a traveled path without marking any waypoints You can retrace your track in both directions Tracks are marked BEGIN and END If you want to keep a record of a certain track log or use the TracBack feature clear the Track Log before you start traveling Goto creates a waypoint called map and guides you to it from your current location Mark creates a new waypoint for later use Refer to the Waypoints Menu Page section for complete information Zoom adjusts the level of map detail viewable
7. on a page The ENTER MARK button e Press to confirm data entry or menu selection e Press and hold to mark a waypoint The UP DOWN buttons e Highlight options on pages and menus e Adjust display contrast on the Satellite Page e Zoom out UP and in DOWN on Map Page Using the Wrist Strap The Foretrex 101 has been designed to comfortably fit your wrist For best perfor mance wear the Foretrex 101 like a watch with the top face of the unit oriented towards the sky A strap extension provides additional length and easily attaches to the existing strap To fasten the Foretrex 101 to your wrist 1 With the strap open place the Foretrex 101 on your wrist 2 Slide the end of the strap through the connector 3 Adjust to fit comfortably and secure the strap using the Velcro Do not adjust too tightly around your wrist as this may restrict blood circulation To add the strap extension 1 Slide the end of the existing strap through the connector on the extension 2 Place the Foretrex 101 on your wrist or arm 3 Slide the end of the extension through the existing connector 4 Adjust to fit comfortably and secure the strap using the Velcro Do not adjust too tightly around your wrist arm as this may restrict blood circulation Overview Getting Started Overview To remove the wrist strap from the Foretrex 101 1 Place your Foretrex 101 on a cloth or soft surface to avoid scratching the case 2 While holding
8. select the desired symbol The symbol list automatically scrolls as you use the arrow buttons to display all the symbols available When the desired symbol is highlighted press the ENTER button To change the name 1 From the Main Menu Page press the UP or DOWN button to highlight MARK Press the ENTER button to display the Mark Waypoint Page Press the UP or DOWN button and highlight the NAME field 001 is the default name for the first waypoint Press the ENTER button to display the Edit Waypoint Name Page Press the ENTER button to display a drop down list of characters Using the UP and DOWN buttons scroll to the desired letter or number and press enter EDIT HAYPOINT HAME Selecting a character for the waypoint name Repeat this process until all characters of the waypoint name are entered Use the UP and DOWN buttons to highlight OK and press ENTER To change the elevation 1 From the Main Menu Page press the UP or DOWN button to highlight MARK Press the ENTER button to display the Mark Waypoint Page Press the UP or DOWN button and highlight the ELEV field and press the ENTER button to display the Enter Correct Elevation Page Use the UP or DOWN button to highlight the desired digit and press the ENTER button to display a selection window Press the UP or DOWN button to select a new number and press the ENTER button Repeat until all numbers are changed Press the UP or DOWN but
9. the Foretrex 101 steady with one hand use a jeweler s band pin Getting Started removing tool or a very soft flat head screwdriver Catch the spring bar s loaded stem and pull it back enough for the band to clear the case s edge To replace the wrist strap on the Foretrex 101 1 To reinstall insert the spring bar into the wristband and place one side of the spring bar into one pinhole 2 Compress the spring bar and snap it into the other pinhole Be sure that the spring bars are secure in the pinholes before using your Foretrex 101 Installing Batteries Overview The Foretrex 101 operates on two AAA alkaline batteries not included which are placed in the back of the unit Rechargeable alkaline NiMH NiCad or lithium batteries may be used Refer to section Set System Page for instructions on selecting battery type Getting Started Stored data will not be lost while batteries are being changed However if batteries are completely discharged and are not changed within a couple of days it may take longer for the unit to get a GPS signal fix To install the batteries 1 Remove the battery cover by inserting a coin in the bottom slot Twist the coin to lift the cover up and pull away 2 Compare the battery polarity with the diagram in the battery compartment and install the batteries accordingly 3 To re install the battery cover slide the top portion into the appropriate slot then snap the bottom section securely to
10. the bottom of the page Change the count down time temporarily by skipping ahead or back using the UP and DOWN arrows This is especially handy when synchronizing your Foretrex timer to other timers such as during a race The timer can stop or start counting up after the count down timer expires Press the UP arrow to reset the timer to the original count down time so it is ready to use again TIP When the timer is at 0 00 press the ENTER button to start the timer count ing up from 0 00 Main Pages Timer Page Timer Page Counting down from 10 00 minutes Timer Page Expired timer 17 Main Menu Pages Main Menu Page TRACKS PPP ROUTES G SETUP Main Menu Page HAP OINTS gt MECREATE HEL f LIST ALL Pal MEAREST PX DELETE ALL Waypoints Menu 18 Main Menu Page Basics The Main Menu Page gives you access to the Foretrex 101 units waypoints tracks routes and setup screens When the Main Menu Page is displayed use the UP or DOWN buttons to highlight the desired sub page Waypoints Tracks Routes or Setup and press ENTER to open that page The Main Menu Page also displays the current date and time along the top of the screen To access a Menu Page 1 From the Main Menu Page use the UP and DOWN buttons to highlight the desired Menu Page such as WAYPOINTS 2 Press the ENTER button to access that Menu Page The following Sub Pages are available Waypoints Tracks R
11. to highlight the month field and then press the ENTER button to display a list of months Select the desired date and press ENTER 3 Use the UP and DOWN buttons to highlight the year field and then press the ENTER button to display a list of years Select the desired date and press ENTER Changing the date 28 Using the Tracks Menu Page Main Menu Pages The Foretrex 101 draws an electronic breadcrumb trail or track log on the Map Page as you travel The Track Log contains information about points along its path including time and position The Foretrex 101 uses this information to allow you to navigate using the Tracks Menu Page saved track The track log starts recording as soon as the Foretrex 101 gets a location fix For the best results clear the track log before you start traveling because when the track log is full in Ee the new track points overwrite the oldest track points The percentage of memory used Tracks l a PPP ROUTES by the current track log displays at the top of the page After the Track Log is Cleared it displays zero percent When the display reaches 100 the most recent track points start Main Menu Page to overwrite the least recent track points if WRAP WHEN FULL is YES To avoid losing track points save the Track Log when it approaches the 99 mark To open the Tracks Menu Page 1 Press the PAGE button to access the Main Menu F PAN amp TRACBACK STNE GE SETUP TRACK 2
12. waypoint then press the ENTER button 4 Press the UP or DOWN button to select the waypoint and press the ENTER button to Goto navigate to that waypoint Waypoints Menu Page 4094 47 937 Review Waypoint Page The Navigation Page is displayed to navigate you to the waypoint destination Simply move in the direction the arrow is pointing to reach your destination PA S S eee rit NOTE You can directly Goto to a waypoint by pressing the GOTO button any 3 13 time a waypoint is selected Press the GOTO button on the Waypoint Review Page the Waypoint List Page when a waypoint is highlighted or the Route Page 0 0 when a waypoint on the route is highlighted Goto Waypoint Navigation Page displaying To access the Review Waypoint Page Options 1 On the Review Waypoint Page press the UP or DOWN button to highlight OPTIONS 2 Press the ENTER button to display the pop up Options list OPTIONS 3 Use the UP and DOWN buttons to highlight the desired option and press ENTER The desired page will then open OFI FTF WO94 47 932 Review Waypoint Page Options 2J Main Menu Pages Waypoints Menu Page FFI FTF OP TIOHS PROJECT f GOTO Ok o00 ELEN 1O88Ft H 3843 44 1 WO94 47 43c Project Waypoint Page EDIT HUMBER fO0 OMmi USE ENTER BUTTOH TO EDIT UPF OOWH BUTTONS TO SELECT Edit Number Page 26 Projecting a Waypoint Using the Project waypoint feature the Foretrex
13. you scroll down you two medium sized data fields are shown and finally one large data field is displayed The Foretrex remembers which Trip Computer Page you previously viewed and displays that same screen when you view the Trip Computer Page again For example if you were monitoring your speed using the one large data field format when you return again to the view the trip computer your speed is displayed in the large data field format Trip Computer Options Press ENTER to display the following Trip Computer Page Options Change Fields Press ENTER when this is highlighted to change the data fields that appear on the right hand side of the display For a complete list and description of the data fields available in the Foretrex refer to Data Field Options found in the Appendix Reset Max Speed Press ENTER when this is highlighted to reset the Maximum Speed achieved during a trip Reset Trip Data Press ENTER when this is highlighted to reset the trip time trip distance odometer and average speed Restore Defaults Press ENTER when this is highlighted to restore the Trip Computer data fields to the defaults Displaying the Timer Page By default the Timer Page is not displayed You must access the Main Menu and enable the Timer Page before you can display and use it To enable the Timer Page 1 Press the PAGE button until the Main Menu Page is displayed 2 Use the UP and DOWN buttons to highlight SETUP and pre
14. 101 can create a waypoint at a specified distance and bearing using an existing waypoint as a reference You can also change the waypoint name symbol and elevation on this page To project a waypoint 1 Select a waypoint from the list on the Waypoints List Page and press the ENTER button to display the Review Waypoint Page 2 Use the UP or DOWN button to highlight OPTIONS and press ENTER 3 Use the UP or DOWN button to highlight PROJECT and press ENTER to display the Project Waypoint Page which shows the numeric name assigned to the new waypoint and with the distance field highlighted 3 Press the ENTER button to display the Edit Number Page Select the digit you wish to change and press the ENTER button to display the drop down number list 5 Press the UP or DOWN button to highlight the correct number and press the ENTER button When all numbers are entered correctly highlight OK and press the ENTER button 6 Use the DOWN button to highlight the bearing field and press the ENTER button to display the Edit Angle Page Use the same method to enter an angle The name symbol and elevation can be changed on this page as well 7 When all changes have been made highlight OK and press the ENTER button to save the waypoint 8 Highlight GOTO and press the ENTER button to begin direct navigation to the waypoint Hunting and Fishing Information Main Menu Pages This feature provides you with a listi
15. 4 Expired and Interval Timer Tones 43 Setup Menu Set Time 44 Sei Time Pap uep ad TUAG A is ts easprtasaacton siesta etncatines AA Daylight Savings Time 0 05 45 Setup Menu Set Display sses 46 Set Display PARC cx srsssssrensssessnanecienonsceess 46 Light TIM OU ccoissccssseeeencnescen 46 COIS Urs S TE 46 Setup Menu Set Units 47 Sei Unlis PARE serres deiars A Position F OFM Ls wpscisasesinncaupiotiestunas A Map DATING assais 48 Distance Speed Elevation and Vertical Sped sssseseras 49 O E E 49 Setup Menu Set Heading 50 Set Heading Papl ncssa 50 North Reference casesssccresnvecensseeee 50 Setup Menu Set Interface 00s0 51 DEL MPC ACS PACE cccisannassicaconevaaresinsieoen 51 Setup Menu Set System 52 BT e E ten cneeseiaec 52 GPS Malerne 53 Ower LING sasinen 53 Appendix ccscsceeeeeesseees 54 Specifications s ssssssseesserssrressressrrrsnnnns 54 Optional ACCESSOTIES ssssisesetrssiias 54 FSI Al E A I4 PPS OUI CE sryvidene sevivsnngee capa venenndunnseenent 54 EON ae E 54 Data Field Options 55 Compliance License and Warranty Information 57 FOC COMPIE 57 Software License Agreement 58 Product Registration scercionmeniera 58 Linited Warranty sersssnr enesis 59 Safety Information 61 i gt CRReer eee eene canta eeneerer err 62 Overview Foretrex 101 Overview Your small rugged and waterproof Foretrex 101 unit is perfect
16. SKIF T 9 00 T TRACKS EEF ROUTES Main Menu Page Timer Page if enabled Trip Computer Page Main Pages Satellite Page 30 GPS Fle SIGHAL Advanced Skyview Using the Satellite Page The Satellite Page shows the Foretrex 101 gathering all the necessary satellite informa tion in order to work The Satellite Page shows you the satellites being acquired in anima tion satellite signal strength and the Foretrex 101 units estimated location accuracy When the message on the Satellite Page no longer reads Acquiring the Foretrex 101 has found your location and you are ready to go miles from the location you last used your Foretrex 101 unit or have not used your Foretrex 101 in more than one month allow time for the unit to track satel lites by leaving it outside with a clear view of the sky for 15 to 30 minutes NOTE If you are using your Foretrex 101 for the first time have moved over 500 Using the Satellite Page Options Press the ENTER button to display the Satellite Page Options Setup Display Press ENTER when SETUP DISPLAY is highlighted to open the Display Setup Page Refer to the next section for information about the Light Timeout and Contrast Advanced Sky View Press ENTER when ADVANCED SKYVIEW is highlighted to switch the animation to the advanced sky view that displays two circles with numbers indicating the satellites the unit is acquiring The bars on the right side of the page in
17. Sa Pen lied PN meme Cc ns y ke Foretrex 101 personal navigator owner s manual Copyright 2004 Garmin Ltd or its subsidiaries Garmin International Inc Garmin Europe Ltd Garmin Corporation 1200 E 15st Street Unit 5 The Quadrangle No 68 Jangshu 2nd Road Olathe Kansas 66062 U S A Abbey Park Industrial Estate Shijr Taipei County Taiwan Tel 913 397 8200 Romsey SO51 9AQ U K Tel 886 2 2642 9199 Fax 913 397 8282 Tel 44 1794 519944 Fax 886 2 2642 9099 Fax 44 1794 519222 All rights reserved Except as expressly provided herein no part of this manual may be reproduced copied transmitted disseminated down loaded or stored in any storage medium for any purpose without prior written consent of Garmin Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed for personal use provided that such electronic or printed copy of this manual or revision must contain the complete text of this copyright notice and provided further that any unauthorized com mercial distribution of this manual is strictly prohibited Information in this manual is subject to change without notice Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes Visit the Garmin Web site www Garmin com for current updates and supplemental informa
18. adjust the screen contrast from the Satellite Page i 2 3 Or Press the PAGE button until you see the Satellite Page Press ENTER to display the Satellite Page Options Press UP DOWN to highlight SETUP DISPLAY from the options menu Press ENTER Use the UP DOWN buttons to highlight the line below CONTRAST Press ENTER Press UP DOWN on the Satellite Page to automatically bring up the contrast slider Press the UP button to make the screen darker or the DOWN button to make it lighter Main Pages Satellite Page JD GPS Fle SIGNAL Satellite Page Options LIGHT TIMEOUT 1 MINUTE CONTRAST es Display Setup 10 Main Pages Map Page Options Using the Map Page The Map Page shows where you are the animated figure and provides a picture of where you are going As you travel the animated figure walks and leaves a trail track log Waypoint names and symbols are also shown on the map To help you better visualize the real world Foretrex 101 automatically rotates the map as you move so that waypoints that are ahead of you are always displayed above the animated figure The Heading Indicator shows the direction you are heading To make sure you can see your entire trip you can change the map scale from 20 feet to 800 miles by pressing and holding the UP button to view a larger area zoom out or the DOWN button for viewing a smaller area zoom in Map Page Options Pre
19. dicate the signal strength of each satellite When the unit is set to display the Advanced Sky View Page you can set the orientation of the map by toggling between Orient Sky Ahead and Orient Sky Northward Toggle back to the normal sky view by pressing the ENTER button when NORMAL SKYVIEW is highlighted About Foretrex Press ENTER to display the software version and copyright information Adjusting the Backlighting and Contrast If the lighting conditions make it hard for you to see the screen adjust the contrast or turn on the backlight You may also make these adjustments through the Main Menu Page Refer to the Setup Menu Set Display section for more information To use the backlight 1 2 Press and release the POWER button from any screen to turn on the backlight The backlight is timed to stay on for 30 seconds Press the POWER button again if you wish to turn the backlight off before the automatic light timeout To adjust the backlight timeout from the Satellite Page 1 BRB W W N Press the PAGE button until you see the Satellite Page Press ENTER to display the Satellite Page Options Press UP DOWN to highlight SETUP DISPLAY from the options menu Press ENTER Press UP DOWN to highlight the line below LIGHT TIMEOUT Press ENTER Press UP DOWN to highlight the desired duration for the backlight to remain on before it automatically turns off Press ENTER to select the desired time limit To
20. e tions The following options are available Change Fields Press ENTER when this is highlighted to change the data fields that appear on the right hand side of the display For a complete list and description of the data fields available in the Foretrex refer to Data Field Options found in the Appendix Restore Defaults Press ENTER when this is highlighted to restore the unit to the default Navigation Page settings When you are navigating to a destination the following option is also displayed Stop Navigation Stops any active navigation displays only when navigating To select a Navigation Page option 1 Press the ENTER button on the Navigation Page The Options Menu displays 2 Press the UP or DOWN button highlight the desired option and press ENTER to make the changes and close the Options Menu 13 14 Main Pages Trip Computer Trip Computer Four small data fields OPTIONS CHANGE FIELDS RESET HAS SPEED f MW RESET TRIP DATA RESTORE DEFAULTS Trip Computer Options Using the Trip Computer The Trip Computer stores information for your trip from the time it is reset until it is re set again The Trip Computer displays information about your trip such as your maximum speed and trip odometer You may change the trip computer data fields to suit your needs The trip computer displays information trip data in three full screens the first screen displays four small data fields As
21. erview that discusses the page how it functions and step by step instructions for using the page and its features The Main Menu chapter provides information on each page in the Main Menu Waypoints Tracks Routes and Setup The section for each page provides an overview that discusses the page how it functions and step by step instructions for using the page and its features The Appendix includes additional information about the Foretrex 101 The Index provides keywords and the pages on which they appear Introduction About This Manual Standard Package Contents 1 Foretrex 101 Unit 1 Strap Extension 1 Wrist Strap 1 Owner s Manual 1 Quick Start Guide Check to see that your package in cludes the items listed above If any parts are missing contact your Garmin dealer immediately il Introduction Care Information Cleaning the Unit and Wrist Strap The Foretrex 101 is constructed of high quality materials and does not require user maintenance other than cleaning Clean the unit using a cloth dampened with a mild de tergent solution and then wipe dry Avoid chemical cleaners and solvents that may damage plastic components The wrist strap should be hand washed with mild detergent in warm or hot water Blot dry then air dry Do not machine wash Storing the Foretrex 101 Do not store the Foretrex 101 where prolonged exposure to temperature extremes may occur such as in the trunk of a car as permanen
22. he Foretrex 101 1 Press and hold the POWER button until the Satellite Page is displayed then release Satellite Page 2 Your Foretrex 101 automatically begins acquiring satellites The GPS signal bar and accuracy fields are shown on the Satellite Page as well as an image that is acquiring satellites The satellite dish icon on the left side of the screen flashes while the Foretrex 101 determines your location 3 Leave the Foretrex 101 with a clear view of the sky for 15 30 minutes initially After the first use it should only take less than a couple minutes to acquire satellites 4 When the Foretrex 101 acquires enough satellite signals to determine your location the satellite dish icon on the left side of the screen stops flashing aN NOTE If you have moved over 500 miles from the location you last used your Foretrex 101 unit or you have not used your Foretrex 101 in more than one month it may take 15 to 30 minutes to determine your location Using the Main Pages Overview All of the information needed to operate the Foretrex 101 is found on six main pages or display screens These pages are the Satellite Map Navigation Trip Computer Timer if enabled and Main Menu Gett ng Started Switching Between the Main Pages Simply press the PAGE button to switch between pages as shown below 30 GPS Flis SIGHAL s FIHAL DIST SFEEL Map Page Navigation Page ACCURACY BACK TO 10 00 TIMER
23. highlighted to move the pointer to any point along the track Press ENTER to then start a TRACBACK or a Goto MARK a waypoint or Pan Track Log ZOOM In or Out The following option is shown only if you are actively navigating to a destination IINE Stop Navigation Press ENTER when this is highlighted to stop any active navigation M mak oe J CLEAR TRACK LOG Navigation refers to any time you are using the Foretrex to guide you to a destination MAP SETUP Map Page Options ll i Main Pages Map Page OO YOU REALLY WAHT Ta CLEAR THE TRACK Lo TES Clearing the Track Log DISTANCE FROH ESTIMATED SPEED DISTANCE H TIHE HEEDED 00 23 08 Measure Distance Page EDIT HUMBER USE ENTER BUTTOH TO EDIT UPOOWH BUTTONS TO SELECT Edit Number Page To clear the track log from the Map Page 1 2 Press the ENTER button while on the Map Page to display the Map Page Options Press the UP or DOWN button to highlight CLEAR TRACK LOG and press the ENTER button At the message DO YOU REALLY WANT TO CLEAR THE TRACK LOG use the DOWN button to highlight YES and press the ENTER button to clear the track log and return to the Map Page To measure distance 1 Press the PAGE button until you see the Map Page Press ENTER to display the Map Page Options Press UP DOWN to highlight MEASURE DISTANCE from the options menu Press ENTER Press ENTER when the field to the right of
24. iew Waypoint Page List All Waypoints Page 19 20 Main Menu Pages To view the nearest waypoints page OO FEB O4 07 56 45pm TRACKS PPP ROUTES G SETUP Main Menu Page 1 Waypoints Menu Page gt From the Main Menu Page press the UP or DOWN button to highlight WAYPOINTS then press the ENTER button Select NEAREST and press the ENTER button to see a listing of the nine closest waypoints by name and distance from your location HEAREST WAYPOINTS 5SH AD WF 5 10 Hmi 3 11 5mi Nearest Waypoints Page 3 Press the UP or DOWN button to select the waypoint and press the ENTER button to display the Review Waypoint Page r fiz LST ALL 1 From the Main Menu Page press the UP or DOWN button to highlight WAYPOINTS PA NEAREST then press the ENTER button ix ee 2 Select DELETE ALL and press the ENTER button Waypoints Menu l l S l 3 A confirmation message box displays asking if you really want to delete all waypoints Press the UP or DOWN button to highlight the correct choice and press the ENTER button to complete the action F DO YOu REALLY E WANT TO DELETE ALL HAVPOINTS Delete All Waypoints Marking a Waypoint Main Menu Pages The Mark Waypoint Page shown to the right allows you to define a location as a waypoint and then change the waypoint symbol name elevation and location latitude and longitude Entering a known location then saving it as a Waypoint
25. n just as on the Mark Waypoint Page You can also delete the waypoint Waypoints Menu Page display the waypoint on the Map Page start a Goto and display the Review Waypoint Page Options To delete a waypoint seats 1 On the Review Waypoint Page press the UP or DOWN button to highlight DELETE areca 2 Press the ENTER button Wo94 47 9372 Review Waypoint Page A confirmation message box displays asking if you really want to delete the waypoint If you do press the UP or DOWN button highlight YES and press ENTER If you do not want to delete the waypoint press the UP or DOWN button highlight NO and press the ENTER button pock JE To view the waypoint on the map PES 1 On the Review Waypoint Page press the UP or DOWN button to highlight MAP 2 Press the ENTER button 3 The Map Page is displayed with the selected waypoint visible Use the DOWN and UP buttons to zoom in and out on the map Delete Waypoint Page 4 Press PAGE to return to the Review Waypoint Page Waypoint on Map 24 To start a Goto from the Review Waypoint Page Main Menu Pages 1 On the Review Waypoint Page press the UP or DOWN button to highlight GOTO 2 Press the ENTER button to activate the GOTO with the selected waypoint as the destination To start a Goto using the GOTO Button 1 Press the GOTO button 2 Press the UP or DOWN button to highlight the alphabetical tab containing the desired
26. ng of best times for hunting and fishing for the chosen waypoint and date Waypoints Menu Page To display the hunting and fishing information i Press the PAGE button to access the Main Menu Press the ENTER button when WAYPOINTS is highlighted to open the Waypoints Menu Page SHG DELETE 2 Highlight LIST ALL and press ENTER to display the Waypoint List Page 2 Select a waypoint from the list and press the ENTER button to display the Review Waypoint Page HOS4 47 432 2 Use the UP or DOWN button to highlight OPTIONS and press ENTER may pors opuells 3 Use the UP or DOWN button to highlight HUNT FISH and press ENTER to display the Hunting and Fishing Page To change the date l Use the UP and DOWN buttons to highlight the date field and then press the ENTER button to display a list of dates Select the desired date and press ENTER Wer FEB 0H AT DOCK AIIERAGE DAY BEST TIM 01 31am 03 3 10m 02 05pm 04 05pm GOOD TIHE 01 42am O8 Y4eam 08 16pm 09 16pm 2 Use the UP and DOWN buttons to highlight the month field and then press the ENTER Hunt and Fish Page button to display a list of months Select the desired date and press ENTER 3 Use the UP and DOWN buttons to highlight the year field and then press the ENTER button to display a list of years Select the desired date and press ENTER NOTE The times displayed are the recognized best and good times for hunting and fishing But be cer
27. outes and Setup The Menu Pages and their options are described in the following pages Waypoints Menu Page Main Menu Pages The Waypoints Menu Page provides access to your waypoints and allows you to delete and create waypoints Waypoints Menu Page To open the Waypoints Menu Page 1 From the Main Menu Page use the UP and DOWN buttons to highlight WAYPOINTS 2 Press the ENTER button to access the Waypoints Menu Page H BD RE LIST ALL To create a waypoint PI NEAREST 1 From the Main Menu Page press the UP or DOWN button to highlight WAYPOINTS Px DELETE ALL then press the ENTER button Waypoints Menu 2 Select CREATE NEW and press ENTER 3 The Mark Waypoint Page is then displayed Your current location is entered as the default location and 001 is entered as the default waypoint name To edit elements of a waypoint such as the symbol name or location refer to the Editing a Waypoint section ELEI 1033 H 38 51 34e 4094 41 927 To select a waypoint from the List All Page 1 From the Main Menu Page press the UP or DOWN button to highlight WAYPOINTS then press the ENTER button 2 Select LIST ALL to see an alphabetical listing of all Waypoints 3 Press the UP or DOWN button to highlight the alphabetical tab containing the desired waypoint then press the ENTER button 4 Press the UP or DOWN button to select the waypoint and press the ENTER button to display the Rev
28. ss ENTER 3 Use the UP and DOWN buttons to highlight SET TIMER and press ENTER 4 Use the UP and DOWN buttons to highlight the field below SHOW TIMER PAGE and press ENTER Use the UP and DOWN buttons to highlight YES and press ENTER Press the PAGE button to exit the menu pages Dw Setting the Timer Before you can use the timer you must set the timer to count down from a particular number such as 10 minutes You can also program what the timer will do when the time has expired and what tones will sound at the timer s expiration and intervals This section will simply explain how to set the timer to count down For more information about setting up the timer refer to the Setup Menu Set Timer section of this guide Main Pages Timer Page Timer E Timer running Set Timer Page Show Timer 15 Main Pages To set the Timer 1 Press the PAGE button until the Main Menu Page is displayed 2 Use the UP and DOWN buttons to highlight SETUP and press ENTER 3 Use the UP and DOWN buttons to highlight SET TIMER and press ENTER 4 Use the UP and DOWN buttons to highlight the field below COUNT DOWN FROM and press ENTER 5 Use the UP and DOWN buttons to highlight the desired time 10 6 5 or 4 minutes and press ENTER You can also enter a CUSTOM time as described below Timer Page ee To enter a custom time et Timer Page Timer Defaults 1 Press the PAGE but
29. ss ENTER when the Map Page is displayed to access the Map Page Options The following options are available Clear Track Log Press ENTER when this is highlighted to clear the track log that is cre ated automatically Measure Distance Press ENTER when this is highlighted to measure the distance between two waypoints Refer to the procedure titled To Measure Distance for instructions on measuring distance Main Pages Map Setup Press ENTER when this is highlighted to adjust the map settings including Orient Map Ahead or Northward When AHEAD is selected the top of the map is oriented in the direction you are currently moving When NORTHWARD is selected the map is always oriented to the North Auto Zoom On or Off When AUTO ZOOM is turned on the map automatically adjusts its scale to display your entire navigating route until you manually change the zoom level When it is turned off you must press the UP or DOWN button to select the appropriate map scale Waypoints Show or Hide Allows you to view the map with or without waypoints Goto Line Bearing or Course Toggles between Bearing always directed at destina tion and follows you as you move and Course fixed from your starting location Defaults Press ENTER when this is highlighted to restore the unit to the default Map Setup settings The following option is shown only if you have an active track log Pan Track Log Press ENTER when this is
30. t damage may result User information such as waypoints and routes will be retained in the units memory without the need for battery power Immersing the Unit in Water The Foretrex 101 is waterproof to IEC Standard 60529 IPX7 It can withstand im mersion in meter of water for 30 minutes Prolonged submersion can cause damage to the unit After submersion be certain to wipe and air dry the unit including the battery compartment before reuse or charging To resolve problems that cannot be remedied using this guide contact Garmin Product Support in the U S A at 800 800 1020 or Garmin Europe at 44 1794 519944 Introduction i Care Information sirivus ii Cleaning the Unit and Wrist Strap ii Sonne Tae Forcie Nlesseerene ii Immersing the Unit in Water ii Table of Contents inrer ii OVOTVICW cccccesececeseeeeesereeses 1 Getting Started 0 0 cscs 1 Forces OMG W eassa i Usine the BUS asucet 2 Using the Wrist Strap uo 3 Installing Batteries ersin 5 Turning on the Foretrex LOL 6 Using the Main Pages ociosas 4 Switching Between the Main Pages 7 Main Pages sssaaa 8 Satellite Page csciccsidessi eviacestenisectivesteceeasess 8 Using the Satellite Page icissssesisisisiscsssas 8 Using the Satellite Page Options 8 Adjusting the Backlighting and Contrast 9 Map Fagien 10 Using the Map Pape osisrasssseniiiossss 10 Map PAGE DUNS aenn ae 10 Navigation Page een 13 Using the
31. tain that they are not in conflict with state and local game laws which may vary from location to location It is your responsibility to know and abide by these laws er FEB 0H AT DOCK 0 ANERAGE DAY BEST TIME pak 01 31am 03 31 02 05pm 04 05 11 GOOD TIHE O7 4eam O8 4e 14 08 16pm 09 16 Changing the date 2 Main Menu Pages Sun and Moon Information This feature provides you with a list of sun rise set and moon rise set times for the se l lected waypoint for the current date A graphic display of the moon phase is also displayed Waypoints Menu Page You may view Sun and Moon information for any date To display the sun and moon information MFI FTF 1 Press the PAGE button to access the Main Menu Press the ENTER button when WAYPOINTS is highlighted to open the Waypoints Menu Page 2 Highlight LIST ALL and press ENTER to display the Waypoint List Page 2 Select a waypoint from the list and press the ENTER button to display the Review Waypoint Page 2 Use the UP or DOWN button to highlight OPTIONS and press ENTER 3 Use the UP or DOWN button to highlight SUN MOON and press ENTER to display the Sun and Moon Page OF TIOHS PROJECT f SUH SET OSU Hoon To change the date RISE 09 31pm SET 09 190m 1 Use the UP and DOWN buttons to highlight the date field and then press the ENTER button to display a list of dates Select the desired date and press ENTER 2 Use the UP and DOWN buttons
32. the base of the unit Installing AAA batteries into the Foretrex 101 NOTE When replacing batteries use only new or fully charged batteries Do not mix Alkaline and NiMH batteries Rechargeable batteries may typically display less capacity than disposable batteries Extensive use of backlighting and key beep tones will significantly reduce battery life Remove the batteries from the unit if you do not plan to use it for several months Storing batteries in the unit for long periods may result in leakage and damage to the battery compartment Battery usage icon shows an estimate of battery life left Four _ squares with the battery outline indicates new batteries are installed aoe ae in the unit batteries Do not incinerate used batteries as internal materials may ignite with explosive violence NOTE Follow the manufacturer s instructions for proper care and disposal of used Overview Turning on the Foretrex 101 After you have placed the batteries in the Foretrex 101 it is ready for use Allow the Foretrex 101 time to track satellites and determine your position the first time you use it Getting Started Upon startup the GPS signal bar appears As the Foretrex 101 locates more satellites and the signal strength increases the bar moves to the right Estimated GPS accuracy displays underneath the GPS signal bar Refer to the previous page for battery installation informa tion 30 GPS Fle SIGHAL To turn on t
33. tion concerning the use and operation of this and other Garmin products Garmin AutoLocate Personal Navigator MapSource TracBack and BlueChart are registered trademarks and PanTrack and Foretrex 101 are trademarks of Garmin Ltd or its subsidiaries and may not be used without the express permission of Garmin March 2004 Part Number 190 00360 00 Rev A Printed in Taiwan Thank you for choosing the Garmin Foretrex 101 To get the most from your new Foretrex 101 read through the Quick Start Guide first then this Owner s Manual to under stand all of the operating features The Quick Start Guide describes the process of navigating the Main Pages and the Option Menus along with some basic unit operations to familiarize you with your new Foretrex 101 right out of the box Read the Quick Start Guide first This Owner s Manual describes the Main Pages of the Foretrex 101 and their options in detail While the Owner s Manual provides some direction on how to select and change items its main intention is to describe each Main Page Option Menu and feature in detail This manual is organized into the following sections The Introduction chapter provides care information and the Table of Contents The Overview chapter provides basic information about the Foretrex 101 The Main Pages chapter provides information on each of the six Main Pages listed in the same order as viewed on the unit The section for each page provides an ov
34. ton to highlight OK and press ENTER to display the Mark Waypoint Page with the corrected elevation To change the location latitude longitude ts From the Main Menu Page press the UP or DOWN button to highlight MARK then press the ENTER button to display the Mark Waypoint Page Press the UP or DOWN button and highlight the LAT LON field and press the ENTER button to display the Edit Location Page Scroll through the latitude and longitude position places using the UP or DOWN button UP button to move right to left DOWN button to move left to right When you reach the position place you want to change stop and press the ENTER button Using the UP or DOWN button scroll through the choices and highlight the one you want Press the ENTER button and the position place is now changed Repeat until all changes are made Press the UP or DOWN button to highlight OK and press ENTER to return to the Mark Waypoint Page Main Menu Pages Waypoints Menu Page ELEN 103 3 H 38 51 347 4094 41 927 Mark Waypoint Page EHTEFR CORRECT ELEWATION m1013Fft USE ENTER BUTTON TO EDIT UP DOhH BUTTONS TO SELECT Enter Correct Elevation Page OLA TI E 38 51 348 HoOqy 47 94 4 USE ENTER BUTTON TO EDIT UP DOWH BUTTONS TO SELECT Edit Location Page 23 Main Menu Pages Review Waypoint Page The Review Waypoint Page allows you to change the waypoint symbol name eleva tion and locatio
35. ton until the Main Menu Page is displayed 2 Use the UP and DOWN buttons to highlight SETUP and press ENTER 3 Use the UP and DOWN buttons to highlight SET TIMER and press ENTER 4 Use the UP and DOWN buttons to highlight the field below COUNT DOWN FROM and press ENTER The Edit Time Page is displayed 5 Use the UP and DOWN buttons to highlight the number position you want to change and press ENTER 6 Use the UP and DOWN buttons to highlight the desired number and press ENTER Repeat this process until the number you would like to count down from is entered 7 Use the UP and DOWN buttons to highlight OK and press ENTER fa carl AT When you use the timer it will count down from the time entered in the steps above ied eee g Hj2EREeT For complete information about the Set Timer Page refer to the Setup Menu Set Timer Edit Time Page section in this manual 16 Using the Timer Page After the Timer Page is enabled and a count down time is entered you can use the timer for a variety of applications such as running and sailboat racing The synchronization and quick reset capabilities make the Foretrex an extremely handy timer To stop and start the timer 1 Press the PAGE button until the Timer Page is displayed To start the timer press the ENTER button when START is displayed along the bottom of the page To stop the timer press the ENTER button when STOP is displayed along
Download Pdf Manuals
Related Search