Sony M673V Handheld Cassette Voice Recorder
Contents
1. To clean the tape head and path Press l and wipe the head capstan and the pinch roller with a cotton swab moistened with alcohol every 10 hours of use To clean the exterior Use a soft cloth slightly moistened in water Do not use alcohol benzine or thinner A Specifications Tape Microcasserte normal position type Recording system 2 track 1 channel monaural Speaker Approx 2 8 cm 1 in dia Tape speed 2 4 cm s 1s ips 1 2 cm s 1 ips Frequency range 300 4 000 Hz with TAPE SPEED switch at 2 4 cm s Input Microphone input jack minijack monaural PLUG IN POWER sensitivity 0 2 mV for 3 kQ or lower impedance microphone Output Earphone jack minijack monaural for 8 300 earphone Power output at 10 harmonic distortion 450 mW Power requirements 3 V DC batteries size AAA R03 x 2 External DC 3V power sources Dimensions w h d incl projecting parts and controls Approx 54 8 x 106 8 x 21 5 mm 2 1 4 x 4 1 4 x in Mass main unit only Approx 92 g 3 3 oz Supplied accessories AC power adaptor 1 M 675V only Battery charge adaptor 1 M 675V only Rechargeable batteries NH AAA 1 2 V typ 800 mAh Ni MH 2 M 675V only Microcassette tape MC 30 1 for the United States and Europe only Alkaline batteries LRO3 SG 2 M 673V M 670V for the United States only Microphone 1 M 673V only Carrying pouch 1 M 673V only Battery carrying case 1 M 675V only Design an2. The button jack has a tactile dot 1 Press the reset button of the tape counter 2 Press IM and insert a standard microcassette with the side to start recording facing the lid 3 Select the desired tape speed 2 4 cm for optimum sound recommended for normal use A 30 minute recording can be made using both sides of the MC 30 microcassette supplied for the United States and Europe only Thereis a tactile dot on this side 1 2 cm for longer recording time A 60 minute recording can be made using both sides of the MC 30 microcassette supplied for the United States and Europe only 4 Set VOR to OFF If you set VOR to ON the unit automatically starts recording the sound and pauses when there is no sound you can save tapes and batteries When the sound is not loud enough set it to OFF or the unit may not start recording 5 Press lt is pressed simultaneously and recording starts While the tape runs the REC BATT lamp lights and flashes depending on the strength of the sound Recording level is fixed At the end of the tape recording stops and the unit turns off automatically Automatic shut off mechanism To Press or slide Stop recording DE Slide P AUSE in the direction of the arrow To release pause recording release e PAUSE Pause recording Start recording during 0 during playback the unit enters the playback recording mode Review the portion just Push up
3. n de cc de 3 V Dimensiones an al fn incluidos componentes y controles Aprox 54 8 x 106 8 x 21 5 mm Masa s lo la unidad principal Aprox 92 g Accesorios suministrados Adaptador de alimentaci n de ca 1 M 675V solamente Adaptador de carga de la pila 1 M 675V solamente Pilas recargables NH AAA de 1 2 V typ 800 mAh Ni MH 2 M 675V solamente Cinta de microcasete MC 30 1 para los Estados Unidos y Europa solamente Pilas alcalinas LR03 SG 2 M 673V M 670V para los Estados Unidos solamente Micr fono 1 M 673V solamente Bolsa de transporte 1 M 673V solamente Estuche de transorte de la pila 1 M 675V solamente El dise o y las especificaciones est n sujetos a cambio sin previo aviso
4. produced in Japan Note The battery life may be shorter depending on the operating condition the surrounding temperature and battery type For maximum performance we recommend that you use alkaline batteries House current to a wall outlet AC power adaptor supplied with M 675V only Connect the AC power adaptor to DC IN 3V and to a wall outlet Use the AC E30HG AC power adaptor not supplied or the supplied AC power adaptor M 675V only Do not use any other AC power adaptor SO Polarity of the plug 8 Notes e Specifications for AC E30HG vary for each area Check your local voltage and the shape of the plug before purchasing Do not touch the AC power adaptor with wet hands e Connect the AC power adaptor to an easily accessible AC outlet Should you notice an abnormality in the AC power adaptor disconnect it from the AC outlet immediately Rechargeable batteries supplied with the M 675V only Charge the supplied rechargeable batteries only with the supplied charge adaptor and the supplied AC power adaptor before using them Full charging takes about 12 hours While charging the CHARGE indicator lights up and when charging is completed it goes off The unit can be used for recording for approximately 12 hours with fully charged rechargeable batteries To charge To a wall outlet CHARGE indicator AC power adaptor Rechargeable batteries NH AAA Recharge the two rechargeable batter
5. FF CUE 4 gt gt REW REVIEW recorded toward gt gt REW REVIEW during the recording Release the button at the point to start playback Take out a cassette DE MP AUSE will also be automatically released when IPH is pressed stop pause release function Note Select the 2 4 cm tape speed for recording if you play back the recorded tape with another unit Otherwise the sound quality may be changed Notes on VOR Voice Operated Recording e The VOR system is affected by the environmental recording conditions When you use the system in a noisy place the unit will stay in the recording mode If the sound is too soft on the contrary the unit will not start recording If you cannot get the results you want set it to OFF e The VOR system may not record the beginning of the sound you want to record because it starts recording only after it catches the sound For an important recording set it to OFF 1 Inserta cassette with the side to start playing facing the lid 2 Select the tape speed to the same speed as that used for recording 3 Press lt 4 Turn VOL to adjust the volume There is a tactile dot beside VOL on to show the direction to turn up the volume At the end of the tape playback stops and the unit turns off automatically Automatic shut off mechanism After the tape has been wound or rewound be sure to press gt E If you plug in headphones not supplied to the EAR jack you will get monaural output fr
6. SG de Sony fabricadas en Jap n Nota La duraci n de la pila puede acortarse dependiendo de las condiciones de funcionamiento la temperatura ambiental y el tipo de pila Para obtener el m ximo rendimiento posible se recomienda emplear pilas alcalinas Alimentaci n dom stica a la toma de alimentaci n lt Adaptador de ca suministrado con el M 675V solamente Conecte el adaptador de alimentaci n ca a DC IN 3 V y a la toma de red Utilice el adaptador de ca AC E30HG no suministrado o el adaptador suministrado M 675V solamente No utilice ning n otro adaptador de alimentaci n de ca Polaridad del enchufe O o Notas e Las especificaciones del AC E30HG var an en funci n de la zona Compruebe la tensi n local y la forma del enchufe antes de la adquisici n e No toque el adaptador de alimentaci n de ca con las manos mojadas e Conecte el adaptador de alimentaci n de ca a una toma de corriente de ca de f cil acceso Si detecta alguna anomal a en el adaptador de alimentaci n de ca descon ctelo inmediatamente de la toma de corriente de ca Pilas recargables s lo se suministran con el modelo M 675V Antes de utilizar las pilas recargables suministradas c rguelas solamente con el adaptador de carga y el adaptador de alimentaci n de ca suministrados La carga completa tarda unas 12 horas Durante la carga se ilumina el indicador CHARGE y ste se apaga una vez finalizada la carga La unidad
7. Sources Choose one of the following power sources Dry Batteries J Insert the batteries with correct polarity Make sure that nothing is connected to the DC IN 3V jack 1 Open the battery compartment lid 2 Insert two size AAA R03 batteries with correct polarity and close the lid To take out the batteries When to replace the batteries Replace the batteries with new ones of the same kind when the REC BATT lamp dims and the J lamp flashes Notes e The unit will play back normally for a while even after the 1 lamp flashes However replace the batteries as soon as you can Otherwise the built in speaker may emit a loud noise and recordings may not be made correctly e In the following cases you do not need to replace the batteries if the amp lamp flashes with the playback sound when you turn up the volume if the lamp lights momentarily when the tape starts running or at the end of the tape if the 91 lamp flashes during FF REW or CUE REVIEW Battery life Approx hours Batteries Recording Playback Sony alkaline LRO3 SG 14 5 9 Sony manganese R03 SB 5 2 5 NH AAA M 675V only 10 6 Measured valued by the standard of JEITA Japan Electronics and Information Technology Industries Association Using a Sony Microcassette Using a tape on which music has been recorded is played at volume setting 7 using speaker When using Sony LRO3 SG alkaline dry batteries
8. accidentally recorded over Break off and remove the cassette tabs To reuse the cassette for recording cover the tab hole with adhesive tape Recording from Various Sound Sources Notes e When you are going to record something that you may not have an opportunity to record again test the unit first before you actually start recording e When recording with an external microphone the VOR system may not work properly because of the difference in sensitivity Recording with an External Microphone Connect a microphone firmly to the MIC jack M 673V use the supplied microphone Other models use a microphone of low impedance less than 3 kQ When using a plug in power system microphone the power to the microphone is supplied from this unit Recording from another equipment Connect another equipment firmly to the MIC jack using the connecting cord not supplied Set this unit to the recording mode and another equipment to the playback mode Playing a Tape EAR VOL PAUSE AN FF CUE lt a gt gt REW REVIEW q D TAPE SPEED gt EG DE amp Battery alert LED FAST PB The button has a tactile dot MIC PLUG IN VOL POWER EAR Microphone VOR REC BATT lt t PAUSE TAPE SPEED gt Tape counter FF CUE lt lt de gt gt REW REVIEW DE amp Battery alert LED Tape counter reset button
9. otro equipo Conecte firmemente otro equipo a la toma MIC mediante el cable de conexi n no suministrado Ponga esta unidad en el modo de grabaci n y el otro equipo en el modo de reproducci n Reproducci n de cintas EAR VOL PAUSE y AK NE FF CUE lt lt gt REW REVIEW S DER DY LED indicador de bater a baja FAST PB El bot n tiene un punto t ctil 1 Inserte una cinta con la cara que va a reproducir mirando a la tapa 2 Seleccione la velocidad de cinta que se utiliz al grabarla 3 Pulse 4 Gire VOL para ajustar el volumen En la unidad principal existe un punto t ctil junto a VOL que muestra la direcci n para subir el volumen Al final de la cinta la reproducci n se detiene y la unidad se desconecta autom ticamente mecanismo de desconexi n autom tica Tras bobinar o rebobinar la cinta aseg rese de pulsar I gt Si conecta auriculares no suministrados a la toma EAR los canales izquierdo y derecho emitir n sonido monof nico Para Pulse o deslice Detener la reproducci n DE detener el avance o rebobinado r pido de cinta Deslice 4 PAUSE en la direcci n de la flecha El indicador REC BATT se apaga Para quitar la pausa en la reproducci n suelte st P A USE Introducir una pausa en la reproducci n Avanzar r pido FF Deslice FF CUE lt 4 gt gt REW REVIEW hacia FF CU
10. the original speed slide the FAST PB switch to the original position ESE Precautions On power e Operate the unit only on 3 V DC For AC operation use the AC power adaptor recommended for the unit Do not use any other type For battery operation use two size AAA R03 batteries On the unit e Use only the MICROCASSETTE standard microcassettes with this unit Non standard cassettes cannot be used because their L dimension see illustration is different Standard Only standard microcassettes have a small indention of side A Non standard UA U i Approx 5 mm Do not leave the unit in a location near heat sources or in a place subject to direct sunlight excessive dust or mechanical shock Should any solid object or liquid fall into the unit remove the batteries or disconnect the AC power adaptor and have the unit checked by qualified personnel before operating it any further Keep personal credit cards using magnetic coding or spring wound watches etc away from the unit to prevent possible damage from the magnet used for the speaker e When you do not use the unit for long remove the batteries to avoid damage caused by battery leakage and subsequent corrosion If the unit has not been used for long set it in the playback mode and warm it up for a few minutes before inserting a cassette Approx 2 5 mm For customers in the USA and Canada RECYCLING NICKEL
11. AAA R03 con la polaridad correcta y cierre la tapa Para extraer las pilas Para ajustar la tapa del compartimiento de las pilas si sta se desprende accidentalmente Cu ndo reemplazar las pilas Sustituya las pilas por otras nuevas del mismo tipo si el indicador REC BATT se aten a y el indicador J parpadea Notas e La unidad reproducir normalmente durante un momento aunque parpadee el indicador J Sin embargo reemplace las pilas lo antes posible En caso contrario es posible que el altavoz incorporado emita un ruido intenso y que las grabaciones no se realicen correctamente e En los casos siguientes no necesitar reemplazar las pilas Si el indicador J parpadea con el sonido de reproducci n cuando aumenta el volumen Si el indicador J se enciende moment neamente cuando la cinta empieza a funcionar o cuando finaliza Si el indicador J parpadea durante FF REW o CUE REVIEW Duraci n de la pila n mero aproximado de horas Pilas Grabaci n Reproducci n Pila alcalina LR03 SG de Sony 14 5 9 Pilas de manganeso R03 SB de Sony 5 25 NH AAA M 675V solamente 10 6 Valor determinado por la norma de la JEITA Japan Electronics and Information Technology Industries Association Utilizando un microcasete Sony Cuando se utiliza el ajuste de volumen 7 y un altavoz para reproducir una cinta que contiene m sica grabada Cuando se utilizan pilas secas alcalinas LRO3
12. E lt 4 durante la detenci n Rebobinar REW Deslice FF CUE BREW REVIEW hacia gt REW REVIEW durante la detenci n Mantenga FF CUE lt 4 lt eR REW REVIEW pulsado hacia FF CUE44 durante la reproducci n y su ltelo en el punto que desee Mantenga FF CUE lt 4 lt eR REW REVIEW pulsado hacia gt REW REVIEW durante la reproducci n y deje de pulsarlo en el punto que desee Buscar hacia delante durante la reproducci n CUE Buscar hacia atr s durante reproducci n REVIEW Iniciar la grabaci n durante 0 la reproducci n AUSE tambi n se liberar autom ticamente si se pulsa gt El funci n de liberaci n de pausa con parada Si deja la unidad encendida despu s de bobinar o rebobinar la cinta las pilas se consumir n con rapidez Aseg rese de desactivar el bot n I gt Ml Nota Si la cinta se ha bobinado por completo mientras se realiza la b squeda hacia atr s durante la reproducci n REVIEW es posible que el interruptor FF CUE lt lt gt gt REW REVIEW no vuelva a la posici n central al soltarlo En este caso desplace el interruptor a la posici n central para iniciar la reproducci n Para aumentar la velocidad de reproducci n Deslice el interruptor FAST PB en la direcci n de la flecha La velocidad de reproducci n aumentar Para volver a la velocidad original deslice el interruptor FAST PB hasta la posici n original E Precauciones Acerca de
13. METAL HYDRIDE BATTERIES Nickel Metal Hydride batteries are recyclable You can help preserve our environment by returning your OVC used rechargeable batteries to the collection and recycling Sam location nearest you N 2 Ni MH ES For more information regarding recycling of rechargeable batteries call toll free 1 800 822 8837 or visit http www rbrc org ATS Caution Do not handle damaged or leaking Nickel Metal Hydride batteries If you have any questions or problems concerning your unit please consult your nearest Sony dealer A Troubleshooting Should any problem persist after you have made these checks consult your nearest Sony dealer You cannot close the cassette compartment lid The cassette is being inserted in the wrong way i has been already pressed The cassette is not being inserted completely The unit does not operate The batteries have been inserted with incorrect polarity The batteries are weak Replace both batteries with new ones AUSE is slid in the direction of the arrow The AC power adaptor is not firmly connected The unit will not run on dry batteries if the AC power adaptor is left plugged into the DC IN 3V jack even though you disconnect the AC power adaptor from the power source Recording cannot be made There is no cassette in the cassette compartment The tab on the tape has been removed To reuse the tape for rec
14. SONY 3 259 967 12 1 Microcassette Corder Operating Instructions Manual de instrucciones en el reverso M 675V 673V 670V 2004 Sony Corporation Printed in China http www sony net For customers in the United States Owner s Record The model number is located at the back of the unit and the serial number is located inside the cassette holder Record these numbers in the spaces provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No Product registration Please register this product on line at www sony com productregistration lt http www sony com productregistration gt Serial No Proper registration will enable us to send you periodic mailings about new products services and other important announcements Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification Thank you You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment To prevent fire or shock hazard do not expose the unit to rain or moisture About This Manual The instructions in this manual are for 3 models There is no difference among M 675V M 673V and M 670V except for the supplied accessories For information about the supplied accessories see Specifications of this manual Preparing Power
15. VOR Si utiliza este sistema en un lugar ruidoso la unidad permanecer en el modo de grabaci n Por el contrario si el sonido es demasiado d bil la unidad no empezar a grabar Si no obtiene los resultados deseados aj stelo en OFF e Es posible que el sistema VOR no grabe el principio del sonido que desea grabar ya que no empieza a grabar hasta que no capta dicho sonido Si se trata de una grabaci n importante aj stelo en OFF Para controlar el sonido Conecte firmemente los auriculares o los cascos no suministrados a la toma EAR No es posible ajustar el volumen de control con VOL Para impedir que una cinta se grabe accidentalmente Rompa y retire las lengiietas de la cinta Para volver a utilizar la cinta para grabar cubra el orificio de la lengiieta con cinta adhesiva Grabaci n de distintas fuentes de sonido Notas e Cuando vaya a grabar algo que no tendr oportunidad de grabar otra vez realice una prueba antes de iniciar la grabaci n e Cuando grabe con un micr fono externo el sistema VOR puede no trabajar adecuadamente debido a la diferencia de sensibilidad Grabaci n con un micr fono externo Conecte firmemente un micr fono a la toma MIC M 673V utilice el micr fono suministrado Otros modelos utilice un micr fono de baja impedancia menos de 3kQ Cuando utilice un micr fono con alimentaci n a trav s de la clavija la alimentaci n del mismo la suministrar la unidad Grabaci n desde
16. alimentaci n de ca de la toma de corriente de pared cuando no vaya a utilizarlo durante un tiempo e No cargar pilas secas Grabaci n Es posible grabar inmediatamente con el micr fono incorporado Cerci rese de que no haya nada conectado a MIC MIC PLUG IN VOL POWER o EAR Micr fono VOR gt REC BATT ton PAUSE TAPE SPEED gt Contador de FF CUE lt gt REW REVIEW DER OY LED indicador de bater a baja cinta Bot n de reinicio del contador de cinta El bot n la toma tiene un punto t ctil M E 1 Pulse el bot n de reinicio del contador de cinta 2 Pulse I gt M e inserte una microcinta est ndar con la cara que desea grabar mirando hacia la tapa 3 Seleccione la velocidad de cinta que desee 2 4 cm para obtener un sonido ptimo recomendado para uso normal es posible realizar una grabaci n de 30 minutos utilizando las dos caras de una microcinta MC 30 suministrado solamente para EE UU y Europa Hay un punto t ctil en esta cara 1 2 cm para mayor tiempo de grabaci n es posible realizar una grabaci n de 60 minutos utilizando las dos caras de una microcinta MC 30 suministrado solamente para EE UU y Europa 4 Sit e VOR en la posici n OFF Si sit a VOR en la posici n ON la unidad inicia autom ticamente la grabaci n del sonido y activa el modo de pausa si no hay sonido de este modo se ahorra cinta y pilas Cu
17. ando el sonido no es suficientemente alto seleccione la posici n OFF o es posible que la unidad no empiece a grabar 5 Pulse Se pulsa ll de forma simult nea y comienza la grabaci n Durante la reproducci n de la cinta el indicador REC BATT se enciende y parpadea en funci n de la intensidad del sonido El nivel de grabaci n es fijo Al final de la cinta la grabaci n se detiene y la unidad se desconecta autom ticamente mecanismo de desconexi n autom tica Para Pulse o deslice Detener la grabaci n DE Deslice PAUSE en la direcci n de la flecha Para quitar la pausa en la grabaci n suelte t PAUSE Hacer una pausa en la grabaci n Iniciar la grabaci n durante la reproducci n la unidad activa el durante la reproducci n modo de grabaci n Empuje FF CUE lt lt e REW REVIEW hacia gt gt REW REVIEW durante la grabaci n Suelte el bot n para iniciar la reproducci n Revisar una parte de cinta reci n grabada Extraer una microcinta gt E MP AUSE tambi n se quitar autom ticamente al pulsar I gt H funci n de liberaci n de pausa con parada Nota Seleccione la velocidad de grabaci n de cinta de 2 4 cm si reproduce la cinta grabada en otra unidad De otro modo la calidad del sonido puede modificarse Notas acerca de la VOR Voice Operated Recording Grabaci n activada mediante la voz e Las condiciones ambientales de la grabaci n afectan al sistema
18. d specifications are subject to change without notice This warranty is valid only in the United States CON SONY Tape Cassette Player Recorder CD Player Mini Disc DAT Radio Head Phone Speaker MIC Personals LIMITED WARRANTY Portable Audio Sony Electronics Inc Sony warrants this Product including any accessories against defects in material or workmanship as follows 1 LABOR For a period of 90 days from the date of purchase if this Product is determined to be defective Sony will repair or replace the Product at its option at no charge or pay the labor charges to any Sony autho rized service facility After the Warranty Period you must pay for all labor charges 2 PARTS In addition Sony will supply at no charge new or rebuilt replacements in exchange for defective parts for a period of one 1 year After 90 days from the date of purchase labor for removal and installation is available from Sony authorized service facilities or a Sony Service Center at your expense To obtain warranty service you must take the Product or deliver the Product freight prepaid in either its original packaging or packaging affording an equal degree of protection to any authorized Sony service facility This warranty does not cover customer instruction installation set up adjustments or signal reception prob lems This warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse ne
19. e durante unos minutos antes de insertar una cinta Para clientes en EE UU y Canad RECYCLADO DE BATERIAS DE NIQUEL HIDRURO METALICO Las bater as de n quel hidruro met lico son reciclables Usted podr ayudar a conservar el medio ambiente devolviendo las bater as usadas al punto de reciclaje m s cercano SBQ 2 RBRC Para m s informaci n sobre el reciclado de bater as llame al n mero gratuito 1 800 822 8837 o visite http w ww rbrc org Precauci n No utilice bater as de niquel hidruro met lico da adas o con fugas Si tiene alguna duda o problema referentes a la unidad p ngase en contacto con el proveedor Sony m s cercano A A A Soluci n de problemas Si sigue teniendo problemas despu s de revisar esta lista consulte al proveedor Sony m s cercano No puede cerrar la tapa del compartimiento de cintas La cinta se est insertando en la posici n incorrecta Ya se ha pulsado l La cinta no se ha insertado completamente La unidad no funciona Las pilas se han insertado con la polaridad incorrecta Las pilas disponen de poca energ a Sustituya las pilas por unas nuevas PAUSE est deslizado en la direcci n de la flecha El adaptador de alimentaci n de ca no se ha conectado con firmeza La unidad no funcionar con pilas secas si el adaptador de alimentaci n de ca est conectado a la toma DC IN 3V aunque dicho adaptador no est conectado a la fuen
20. gli gence commercial use or modification of or to any part of the Product including the antenna This warranty does not cover damage due to improper operation or maintenance connection to improper voltage supply or attempted repair by anyone other than a facility authorized by Sony to service the Product This warranty does not cover Products sold AS S or WITH ALL FAULTS or consumables such as fuses or batteries This warranty is valid only in the United States Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service This warranty is invalid if the factory applied serial number has been altered or removed from the Product REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIB ITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU LAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you In addition if you enter into a service contract with the S
21. ies together To take out the rechargeable batteries from the charge adaptor push the O side of the battery first and then remove the O side To use Insert the batteries with correct polarity e When using the supplied charge adaptor charge the rechargeable batteries specified on the charge adaptor only Do not charge any other batteries e When charging use the supplied AC power adaptor only e If there is distortion of sound or excessive noise or if the unit does not operate properly turn off the unit and recharge the two rechargeable batteries together e The rechargeable batteries will discharge gradually even when not in use Be sure to charge them before use e Charging and operation should be made in temperature ranges 5 C to 40 C 40 F to 104 F e The charge adaptor will become warm during charging but this is not a sign of problem e Do not use or leave the charge adaptor AC power adaptor and rechargeable batteries in a location near heat sources or in a place subject to direct sunlight or excessive moisture e Unplug the AC power adaptor from the wall outlet when it is not to be used for long Do not charge dry batteries Recording You can record right away with the built in microphone Make sure that nothing is connected to the MIC jack To monitor the sound Connect an earphone not supplied firmly to the EAR jack The monitor volume cannot be adjusted by VOL To prevent a cassette from being
22. la alimentaci n e Utilice la unidad s lo con 3 V cc Para utilizar ca utilice el adaptador de ca recomendado para la unidad No emplee otro tipo de adaptador Si va a utilizar pilas emplee dos pilas tama o AAA R03 Acerca de la unidad e Utilice s lo MIEROCASSETTE microcintas est ndar con esta unidad Las cintas no est ndar no pueden utilizarse porque su dimensi n L consulte la ilustraci n es diferente Est ndar S lo las microcintas est ndar tienen una peque a hendidura en la cara A No est ndar p UJ t Aprox 5mm Aprox 2 5 mm e No coloque la unidad cerca de fuentes de calor ni en un lugar expuesto a la luz del sol a cantidades de polvo excesivas o a golpes mec nicos e Si se introduce alg n objeto s lido o se derrama l quido dentro de la unidad extraiga las pilas o desconecte el adaptador de alimentaci n de ca y haga que personal cualificado revise la unidad antes de volver a utilizarla e Aleje las tarjetas de cr dito personales con codificaci n magn tica o los relojes de cuerda etc de la unidad para evitar que se produzcan posibles da os por el im n del altavoz e Si no va a utilizar la unidad durante un periodo de tiempo prolongado extraiga las pilas para evitar que se produzcan da os derivados de fugas del electrolito o corrosi n e Si la unidad no se ha utilizado durante un periodo de tiempo prolongado active el modo de reproducci n y deje que se calient
23. om both left and right channels To Press or slide Stop playback stop fast gt E forward or rewind Pause playback Slide PAUSE in the direction of the arrow REC BATT lamp goes off To release pause playback release PAUSE Fast forward FF Slide FF CUE lt lt P REW REVIEW toward FF CUE lt lt during stop Slide FF CUE lt lt e gt REW REVIEW toward PP REW REVIEW during stop Search forward during Keep FF CUE t gt gt REW REVIEW playback CUE pushed toward FF CUE lt 4 during playback and release it at the point you want Search backward during Keep FF CUE lt lt gt gt REW REVIEW playback REVIEW pushed toward gt REW REVIEW during playback and release it at the point you want Rewind REW Start recording during 0 playback mP AUSE will also be automatically released when I gt is pressed stop pause release function Tf you leave the unit after the tape has been wound or rewound the batteries will be consumed rapidly Be sure to press I gt W Note Tf the tape is completely rewound while searching backward during playback REVIEW the FF CUE lt 4 gt gt REW REVIEW switch may not return to the center position when you release the switch In this case push back the switch to the center to start playback To increase the playback speed Slide the FAST PB switch in the direction of the arrow The playback speed will be increased To return to
24. ony Partnership within 90 days of the date of sale the limitation on how long an implied warranty lasts does not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state For your convenience Sony Electronics Inc has established telephone numbers for frequently asked questions To locate the servicer or dealer nearest you or for service assistance or resolution of a service problem or for product information or operation call Sony Customer Information Services Center 1 800 222 7669 or visit the Sony Web Site wwwsony com For an accessory or part not available from your authorized dealer call 1 800 488 SONY 7669 D 455714702 ADVERTENCIA Para evitar incendios o el riesgo de electrocuci n no exponga la unidad a la lluvia ni a la humedad Acerca de este manual Las instrucciones de este manual corresponden a los 3 modelos No existen diferencias entre los modelos M 675V M 673V y M 670V a excepci n de los accesorios suministrados Si desea obtener informaci n acerca de los accesorios suministrados consulte el apartado Especificaciones de este manual Fuentes de alimentaci n Elija una de las siguientes fuentes de alimentaci n Pilas secas Inserte las pilas con la polaridad correcta Compruebe que no se ha realizado ninguna conexi n a la toma DC IN 3V 1 Abra la tapa del compartimiento de las pilas 2 Inserte dos pilas tama o
25. ording cover the tab hole with adhesive tape The batteries are weak Replace both batteries with new ones Recording is interrupted The VOR switch is set to ON When you do not use VOR set it to OFF Recording cannot be erased completely The head is contaminated See Maintenance Playback cannot be made The tape has reached the end Rewind the tape No sound comes from the speaker The earphone is plugged in Unplug it The volume is turned down completely The sound drops out or comes with excessive noise The volume is turned down completely The batteries are weak Replace both batteries with new ones The head is contaminated See Maintenance Direct placement of the cassette tape on the speaker resulted in magnetization and deteriorated tonal quality Use the unit away from radiowave emitting devices such as cellular phones Tape speed is too fast or too slow or the sound is distorted in the playback mode Improper setting of the TAPE SPEED switch Set it to the same speed as that used for recording The FAST PB switch is slid in the direction of the arrow The batteries are weak Replace both batteries with new ones During CUE REVIEW the tape stops or does not run You cannot fast forward or rewind The batteries are weak Replace both batteries with new ones gt gt Maintenance Pinch roller Head
26. puede utilizarse para grabar durante aproximadamente 12 horas con las pilas recargables completamente cargadas Carga Adaptador de carga a la toma de pared Indicador CHARGE Adaptador de 3 alimentaci n Pilas recargables de ca NH AAA Recargue las dos pilas recargables a la vez Para extraer las pilas recargables del adaptador de carga presione primero el extremo O de la pila y luego extraiga el extremo O Utilizaci n Inserte las pilas con la polaridad correcta Notas e Si utiliza el adaptador de carga suministrado cargue nicamente las pilas recargables especificadas en el adaptador de carga No cargue ning n otro tipo de pila e Al cargar utilice nicamente el adaptador de alimentaci n de ca suministrado e Si se produce distorsi n de sonido o ruido excesivo o si la unidad no funciona correctamente apague la unidad y recargue las dos pilas recargables juntas e Las pilas recargables se descargar n gradualmente aunque no se utilicen Aseg rese de cargarlas antes de utilizarlas e La carga y el uso deber an realizarse en rangos de temperatura desde 5 C a 40 C e El adaptador de carga se calentar durante la carga pero eso no indica un problema e No utilice ni deje el adaptador de carga adaptador de alimentaci n de ca y pilas recargables en una ubicaci n cercana a fuentes de calor ni en lugares expuestos a la luz solar directa o a un exceso de humedad e Desenchufe el adaptador de
27. rabaci n El interruptor FAST PB est deslizado en la direcci n de la flecha Las pilas disponen de poca energ a Sustituya las pilas por unas nuevas Durante la CUE REVIEW b squeda revisi n la cinta se detiene o no funciona No es posible avanzar r pido ni rebobinar Las pilas disponen de poca energ a Sustituya las pilas por unas nuevas Mantenimiento Cabrestante Rodillo de apriete Cabezal Para limpiar el cabezal y la pista de la cinta Pulse lt y limpie el cabezal el cabezal m vil y el cilindro de paso con un bastoncillo de algod n humedecido en alcohol cada 10 horas de uso Para limpiar el exterior Utilice un pa o suave ligeramente humedecido en agua No emplee alcohol bencina ni diluyentes C C Especificaciones Cinta icrocasserTe tipo de posici n normal Sistema de grabaci n 2 pistas 1 canal monof nico Altavoz Aprox 2 8 cm de di metro Velocidad de cinta 24 cm s 1 2 cm s Gama de frecuencias 300 4 000 Hz con el interruptor TAPE SPEED ajustado en 2 4 cm s Entrada Toma de entrada para micr fono minitoma mono PLUG IN POWER Sensibilidad de 0 2 mV para micr fono con impedancia de 3 kQ o menos Salida Toma de auricular minitoma mono para auricular de 8 a 300 Q Salida de alimentaci n al 10 de distorsi n arm nica 450 mW Requisitos de alimentaci n Pilas tama o AAA R03 de 3 V cc x 2 Fuentes externas de alimentaci
28. te de alimentaci n No es posible grabar No hay ninguna cinta en el compartimiento Se ha retirado la lengiieta de la cinta Si desea volver a utilizar la cinta para grabar cubra el orificio de la lengiieta con cinta adhesiva Las pilas disponen de poca energ a Sustituya las pilas por unas nuevas La grabaci n se interrumpe El interruptor VOR est situado en ON Cuando no utilice VOR col quelo en OFF La grabaci n no puede borrarse por completo El cabezal est sucio Consulte el apartado Mantenimiento No es posible reproducir La cinta ha llegado al final Rebob nela El altavoz no emite sonido alguno Los auriculares est n conectados Descon ctelos El volumen est bajado del todo El sonido se pierde o se oye ruido excesivo El volumen est bajado del todo Las pilas disponen de poca energ a Sustituya las pilas por unas nuevas El cabezal est sucio Consulte el apartado Mantenimiento La cinta se coloc directamente sobre el altavoz lo que caus la magnetizaci n y el deterioro de la calidad tonal No utilice la unidad cerca de dispositivos que emitan ondas radioel ctricas como tel fonos celulares m viles La velocidad de la cinta es demasiado r pida o demasiado lenta en el modo de reproducci n Configuraci n inadecuada del interruptor TAPE SPEED velocidad de la cinta As gnele la misma velocidad que utiliz para la g
Download Pdf Manuals
Related Search