GE Profile PDW8060GSS Built
Contents
1. STEP 15 INSTALL TOEKICK e Loosen depth adjustment screws inside the bracket Slide bracket out to proper depth Tighten screws e Attach supplied toekick to brackets with screws C provided Do not tighten e Adjust the toekick to touch the floor Tighten screws Adjust to Touch Floor STEP 16 Installation Instructions ADJUST SIDE FILLER STRIPS e Open the door fully e Loosen but do not remove screws holding the top and side trims e Adjust trim to cover opening gap Tighten screws Adjust Side Trim o Meet Cabinetry Loosen Screws 15 Note While performing installations described in this book safety glasses or goggles should be worn Note Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice 0616 400 350 Pub No 31 30545 Dwg No 203C1559P085 N D 318 11 012. This will allow easy removal for any future service Corner Installation e When installing into a corner allow 2 min clearance between dishwasher and adjacent cabinet or wall e Allow 24 1 2 min clearance from the front of the dishwasher for door opening Countertop Dishwasher a 24 1 2 Clearance for Door Opening 2 Minimum Installation Preparation DRAIN REQUIREMENTS e Follow local codes and ordinances e Do not exceed 10 feet distance to drain e To prevent back flow into the dishwasher connect drain line to an air gap or use a 30 high drain loop depending on local codes e Air gap must be used when waste tee or disposer connection is less than 18 above the floor to prevent siphoning DETERMINE DRAIN METHOD The type of drain installation depends on the following questions Do local codes or ordinances require an air gap _ Will waste tee or disposer connection be less than 18 above the floor Will installation have a high drain loop less than 30 above the floor If the answer to ANY of these questions is YES Method 1 MUST be used e If all answers are NO either method may be used A CAUTION An air gap MUST BE USED if the drain hose is con nected to a waste tee or disposer lower than 18 above the floor level e Failure to provide the proper drain connection using an air gap or a 30 min high drain loop will re
3. this appliance CESS POUR ASSURER LA S CURIT PERSONNELLE il faut enlever le fusible ou couper le courant au disjoncteur avant de commencer l installation Avec cet appareil il ne faut pas utiliser de rallonge ni d adaptateur de prise Electrical Requirements e This appliance must be supplied with 120V 60 Hz and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse e Wiring must be 2 wire with ground and rated for 75 C 176 F e If the electrical supply does not meet the above require ments call a licensed electrician before proceeding Grounding Instructions Cable Direct This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and be connected to the equipment grounding terminal or lead on the appliance Grounding Instructions Power Cord This appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances NUTS The improper connection of the equip ment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service represen tative if you are in doub
4. 6 LEVEL DISHWASHER e Carefully upright the dishwasher be careful not to bend the leveling legs e Check to be sure the dishwasher is level and is adjusted to fit the installation cutout height 11 STEP 7 SLIDE DISHWASHER INTO OPENING DO NOT PUSH AGAINST THE FRONT PANEL WITH KNEES DAMAGE WILL OCCUR e Insert drain hose into the cabinet wall hole If a power cord is used guide the end through a separate hole e Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher e Slide dishwasher into the opening a few inches at a time As you proceed pull the drain hose through the cabinet wall under the sink e Check to be sure there is no interference with waterline or house wiring e Again check to be sure the dishwasher is level STEP 8 CONNECT WATER LINE NOTE If you are using an existing water line cut 1 off the end Always use a new ferrule and compression nut e The water supply line should be flushed to clear any foreign material before connecting to the dishwasher e Make sure there are no sharp bends or kinks to restrict water flow e Insert water line into the 90 elbow e Slide ferrule against elbow and secure with compression nut e Replace access panel plate Compression Nut ok 7 J Hot Water 90 Elbow Supply Line Installation Instructions STEP
5. a full length door or a modified door to accept a full cabinet panel without the traditional access panel e Side tub flange trim is adjustable and will conceal any slight gap between the dishwasher and adjacent cabinetry e These dishwashers may be installed beneath countertops of stone or other materials that will not accept screws No trim kit required Standard installation in 24 deep cabinets e In standard 24 deep cabinets the dishwasher door will be flush with adjacent cabinetry e Models with 3 4 thick custom door panel will fit flush with adjacent cabinetry Supplied or Custom Toekicks e A 2 piece toekick is supplied with all models The toekick is height and depth adjustable e Depending on cabinetry style a custom toekick can also be installed to match cabinetry Care must be taken to assure door swing clearance above the toekick ADA Compliant Installation below 34 high countertops A reduced height installation 32 1 2 min beneath a 34 countertop can be accomplished by removing the front leveling legs The rear legs should be screwed in flush with the bottom support as shipped The front of the dishwasher must be shimmed to level the dishwasher Water and electrical must be routed through the back wall Installation Preparation MATERIALS YOU WILL NEED e5 Se ds Materials Required for All Installations Screw Type Clamps O 90 Elbow 3 8 NPT external thread on one end opposite end sized to fi
6. that most of the water has drained If not check that disposer plug has been removed and that air gap is not plugged O Cancel the dishwasher cycle and complete the installation O Remove protective film if present from the control panel and door 13 POSITION AND LEVEL THE DISHWASHER Door Rub Door Rub Me a ee On Right On Left A Hand Side Hand Side Adjust Adjust This N lt This Leg Leg O Verify water supply and drain lines are not kinked or in contact with other components O Turn on the sink hot water faucet and verify water temperature Incoming water temperature must be between 120 F and 150 F 120 F min temperature is required for best wash performance O Turn on water supply O Open the door Check to be sure Insulation Board does not interfere with door opening CHECK WATER FILL LEVEL For best performance check the water fill level Run through a complete RINSE ONLY cycle to ensure it is emptying and filling correctly For low water pressure situations run the RINSE ONLY cycle 3 times Half way through the final RINSE ONLY cycle pause the dishwasher and check the water level inside the dishwasher If the water level is not above the minimum water level marked on the lower spray support tower increase the fill level 1 Ensure the dishwasher is not running through a cycle Depress the WATER TEMP button for 10 seconds until the second buzzer sounds except on ZBD6600 2 Press the START CANCE
7. 9 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES e The dishwasher is supplied with a 72 long drain hose e If a longer drain hose is required add up to 48 of length for a total of 10 ft length e Secure the drain hose to the air gap waste tee or disposer with clamps e Make sure drain hose is not kinked IMPORTANT When connecting drain line to disposer check to be sure that drain plug has been removed DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE Method 1 Air gap with waste tee or disposer Waste Tee Installation Disposer Installation Method 2 High drain loop with waste tee or disposer Waste Tee Installation Fasten to underside of countertop Fasten to underside A of countertop A A isposer Installation Waste Tee Installation 12 STEP 10 CONNECT ELECTRICAL FOR DIRECT WIRE ONLY If a power cord with plug is used plug it into the wall outlet and continue with next step Verify that power is turned off at the source Insert power cord wires through strain relief and tighten e Locate the three dishwasher wires white black and green with stripped ends Insert wire through the small hole in the junction box Use wire connectors to connect incoming ground to green white to white and black to black e Install junction box cove
8. AMPLE A 30 1 2 minus 5 3 8 is equal to 25 1 8 O J 23 1 8 t 1 Measure Dimension A from underside of countertop to bottom of adjacent cabinets 2 Subtract 5 3 8 Control panel height is 5 1 8 Allow e Cut the panel to the dimensions shown 1 4 clearance between countertop and control e The bottom left and right corners should be cut at panel 1 4 radius See illustration 3 The custom panel fits against bottom of the control panel Installation Instructions BEFORE YOU BEGIN CUSTOM PANEL INSTALLATION If you intend to install custom door panels on some models refer to trim kit installation instructions Custom panels should be in place before installing the dishwasher STEP 1 REMOVE PACKAGING Cut the shipping carton and use it as a pad beneath the dishwasher This will protect the finished floor in the kitchen e Remove wrapping and uncoil the drain hose in the back of the dishwasher Do not remove rear insulation blanket e Lay the dishwasher on it s back Do not kink or crush the drain hose INSTALL LEVELING LEGS 1 1 4 Min Remove Red Plugs Unscrew omni Rear Legs to Installation Height Rear Insulation Blanket e Measure installation opening from the floor to the bottom of the countertop e Install the front leveling legs into holes on the brack ets Use a wrench to screw the legs in until the overall he
9. Installation Instructions If you have questions call 800 GE CARES or visit our website at www GEAppliances com Built In Dishwashers PDWws8000 PDW8060 Design Guide with Installation Instructions GE Appliances Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully IMPORTAN T Save these instructions for local inspector s use Observe all governing codes and ordinances e Note to Installer Be sure to leave these instruc tions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference e Skill Level Installation of this dishwasher requires basic mechanical and electrical skills Proper installa tion is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty e Completion Time 1 to 2 Hours New installa tions require more time than replacement installa tions CONTENTS Design Information Product Dimensions Models Available Advance Planning Installation Preparation Materials You Will Need Tools You Will Need Parts Supplied Prepare Dishwasher Enclosure Drain Requirements Prepare Electrical Wiring Prepare Hot Water Line Custom Panel Dimensions Custom Panels for PDW8000 IMPORTAN T The dishwasher MUST be installed to allow for future removal from the enclosure if service is required If you received a damaged dishwashe
10. L button to select fill time as per chart 65 seconds is the factory setting 3 To test time press DELAY START The dishwasher will start filling Listen for the dishwasher to complete filling Once filled the fill level must be checked to ensure fill time is correct 4 Once complete press the WATER TEMP button to exit fill time mode Continue to press the START CANCEL button until the desired indicator is illuminated Cycle Statue Indicators Fill Time SENSING 60 seconds WASHING 65 seconds RINSING 70 seconds DRYING 80 seconds CLEAN 90 seconds Installation Instructions STEP 14 SECURE DISHWASHER TO CABINET AND COUNTERTOP To maintain position and alignment it is recommended the dishwasher be secured to the countertop and adjacent cabinets Secure dishwasher to countertop e Drill pilot holes through the mounting bracket and into the underside of the countertop Secure with screws A provided IMPORTANT To avoid damage to your dishwasher drive screws straight and flush Protruding screw heads may scratch the top of the escutcheon or door and can interfere with door closing Secure dishwasher to adjacent cabinets e Remove plastic plugs button on the inside of the dishwasher frame One on each side e Drill pilot holes through the dishwasher holes and into the adjacent cabinets Install screws B provided e Replace plastic plug buttons
11. d unnecessary charges review this list carefully O Check to be sure power is OFF O Open the door and remove all foam and paper packaging O Pull lower rack out about half way Check to be sure it does not roll back or forwards on the door If the rack moves adjust leveling legs STEP 13 DISHWASHER WET TEST O Turn on power supply O Select the normal cycle and press the start button O The control will indicate a slow no fill by flashing the CHINA CRYSTAL LIGHT WASH OR WASH CYCLE light Check water supply then adjust fill time according to the chart shown O Check to be sure that water enters the dishwasher wait up to 2 minutes If water does not enter the dishwasher check to be sure that water is turned on O Check for leaks under the dishwasher If a leak is found turn power and water off then tighten connections Restore power and water supply O Check for leaks around the door A leak around the door could be caused by door rubbing or hitting against adjacent cabinetry Reposition the dishwasher if necessary O After the dishwasher drains check drain lines If leaks are found turn power off correct as necessary O The control will indicate a slow no drain by flashing the RINSE ONLY SANI WASH or HEAT OPTIONS Check that the airgap is clear of debris and that the knockout in the disposer or waste tee is fully removed Check that the drain hose is not kinked O Open the dishwasher door and make sure
12. ight of the dishwasher is 1 4 less than the installa tion opening height Note Install the legs as shown 1 1 4 min from the bottom of the bracket e Remove and discard the red plugs from the front holes 10 REMOVE ACCESS COVER i AN Insulation Board Junction Box Access Cover e Remove sound insulation board and the access cover plate e Install UL listed strain relief on junction box INSTALL 90 ELBOW Thread Seal Tape e Install the 90 elbow onto the water inlet Use thread seal tape or pipe thread compound Thread seal tape should be wrapped in same direction as the threads on the elbow e The 90 elbow should face the inlet water line Installation Instructions STEP 5 INSTALL POWER CORD SKIP THIS STEP IF DISHWASHER WILL BE DIRECT WIRED e Maximum power cord length is 6 ft e The power cord and connections must comply with the National Electrical Code Section 422 and or local codes and ordinances Insert power cord wires through strain relief and tighten e Strip 1 2 insulation from ends of power cord wires e Connect incoming power cord white to dishwasher white black to black and ground to dishwasher green wire Use UL listed wire connectors of appropriate size e Install junction box cover with screws provided Be sure wires are not pinched under the cover STEP
13. ional 1 1 2 dia hole to admit the line Ifa Right Side Entry power cord with plug is used it must pass through a separate hole Approx 40 from Wall Water Line Connection e Turn off the water supply e Install a hand shut off valve in an accessible loca a tion such as under the sink Optional but strongly A Side Entry recommended and may be required by local codes imee A N gt from Floor e The hot water line should be 3 8 O D copper tubing or 1 2 O D plastic tubing The line must e Adjust water heater to deliver temperatures of 120 F to extend forward at least 30 from the left side or 40 150 F from the Tear wall Flush water line to clean out debris The water line must be long enough to form a The hot water supply line pressure must be 20 120 PSI smooth natural loop with no sharp bends or kinks between the cutout entry Custom Panel Dimensions CUSTOM PANEL FOR MODELS 3 4 PANEL WITH ZPF675 TRIM KIT PDW8000 The custom panel size varies depending on your Panel kits must be ordered separately Installation installation of any custom panel should be completed before the dishwasher is installed Countertop Custom Panel Size Top Cabinets 1 4 PANEL WITH GPF725 TRIM KIT h 3 4 Thick Door Panel Floor lle i 23 1 8 1 4 Thick pottom of 3 4 Max Door Panel 1 4 Adjacent Cabinetry Height is equal to A minus 5 3 8 See EX
14. outside of the dishwasher Check contents against illustrations to insure that all parts are included O 2 piece toekick O 6 screws see illustration O 2 leveling legs O Junction box cover Junction Box Cover with screws Screws C 2 Color Matched Toekick Screws Screws B 2 Cabinet Mounting Screws Screws A 2 Countertop Mounting Screws PREPARE DISHWASHER ENCLOSURE This Wall Area I must be Free of gt Pipes or Wires 34 to 35 Underside of Countertop to Floor 24 A Min e The rough cabinet opening must be at least 24 deep 23 5 8 min to 24 wide The height should be 34 min and 35 max Note ADA installation beneath 34 high countertops may be accom plished by removing front leveling legs Drain hose water and electrical must be routed through the cutout on the back of the dishwasher e The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage e The dishwasher must be fully enclosed on the top sides and back but should not support any part of the enclosure 2 Leveling Legs 2 Piece Toekick with Sound Insulation e The floor inside the opening must be even and level with the finished floor of the kitchen If the kitchen floor is tile it may be higher than the floor of the installation cutout Pieces of wood may be placed into the cutout floor to make it level or higher than the room floor
15. r you should immediately contact your dealer or builder READ CAREFULLY KEEP THESE INSTRUCTIONS FOR YOUR SAFETY Read and observe all CAUTION and WARNINGS shown throughout these instructions Installation Instructions Step 1 Remove Packaging Step 2 Install Leveling Legs Step 3 Remove Access Covers Step 4 Install 90 Elbow Step 5 Install Power Cord Step 6 Level Dishwasher Step 7 Slide Dishwasher into Opening Step 8 Connect Water Line Step 9 Connect Drain Line Step 10 Connect Electrical Step 11 Position and Level Dishwasher Step 12 Pre Test Check List Step 13 Dishwasher Wet Test Step 14 Secure Dishwasher to Cabinet or Countertop Step 15 Install Toekick Step 16 Install Side Filler Strips Design Information PRODUCT DIMENSIONS 34 Adjustable to 35 DISHWASHER MODELS Traditional Built In PDW8000 BB Black Accepts 1 4 or 3 4 custom panels PDW8000 WW White Accepts 1 4 or 3 4 custom panels PDW8000 CC Bisque Accepts 1 4 or 3 4 custom panels Trim Kits e GPF725W white GPF725B black or GPF725C bisque custom panel kits supports a 1 4 thick custom door panel e ZPF675W white ZPF675B black ZPF675C bisque custom panel kits support a 3 4 thick custom door panel Stainless Steel Built In PDW8060 SS Stainless steel door ADVANCE PLANNING e These dishwashers are designed for versatility adaptable to virtually any installation e All models have
16. r with screws provided Check to be sure that wires are not pinched under the cover e Reinstall Insulation Board in position The board should be secured so it does not interfere with door opening SATS If house wiring is not 2 wire with ground a ground must be provided by the installer When house wiring is aluminum be sure to use UL Listed anti oxidant compound and alumi num to copper connectors Ad AVERTISSEMENT Si l installation lectrique de la maison n est pas a deux fils plus terre Vinstallateur doit installer un fil de mise la terre Si l installation lectrique de la maison est en alu minium il faut prendre soin d utiliser des compos s antioxydants et des w connecteurs aluminium cuivre sur la liste UL Installation Instructions STEP 11 e Check to be sure the dishwasher is adjusted to correct height and is centered in the cutout e Open and close the door to insure proper operation of the door If there is any binding or rubbing readjust leveling legs Use a wrench to make adjustments e If the door rubs on the right side of the cabinet extend the left rear leg by unscrewing it one quarter turn e If the door rubs against the left side of the cabinet extend the right rear leg by unscrewing it one quarter turn e Check level again Repeat the procedure if necessary STEP 12 PRE TEST CHECK LIST Installation service calls are not covered by your warranty To avoi
17. sult in improper draining of the dishwasher which may cause damage or poor wash performance Ay PRUDENCE Il DOIT Y AVOIR une coupure antirefoulement si le tuyau de vidange est branch sur un raccord d gout ou un broyeur d ordures moins de 46 cm 18 po du sol e Si la vidange n est pas branch e correctement en utilisant une coupure antirefoulement ou un boucle d gout d au moins 76 cm 30 po de haut l coulement de l eau du lave vaisselle n est pas bon ce qui peut causer des dommages ou un mauvais lavage de la vaisselle Method 1 Air Gap with Waste Tee or Disposer An air gap must be used when the waste tee or disposer connection is less than 18 from the floor a A Ze Method 2 High Drain Loop with Waste Tee or Disposer Install waste tee or disposer and air gap according to manufacturer s instructions _ le 12 Min CABINET PREPARATION e Drill a 1 1 2 dia hole in the cabinet wall within the shaded areas shown for the drain hose connec tion The hole should be smooth with no sharp edges Installation Preparation PREPARE ELECTRICAL WIRING CAT FOR PERSONAL SAFETY Remove house fuse or open circuit breaker before beginning installation Do not use an extension cord or adapter plug with
18. t that the appli ance is properly grounded Alternate Receptacle Location 1 1 2 Dia Hole Max A Receptacle 18 Location w aa T White Electrical Connections to Dishwasher The dishwasher junction box is located on the right side at the front of the dishwasher The electrical cable must extend forward at least 24 to reach the junction box when dishwasher is installed e The wiring may enter the opening from either side rear or the floor within the shaded area e Cut a 1 1 2 max dia hole to admit the electrical cable or use the same hole cut for the drain hose The hole must be free of sharp edges If the cabinet wall is metal the hole edge must be covered with a bushing e For power cord connections install a 3 prong ground ing type receptacle in the sink cabinet rear wall 6 min or 18 max from the opening and 6 to 18 above the floor AX AVERTISSEMENT r Le mauvais branchement du fil de mise la terre de l quipement peut causer un choc lectrique En cas de doute sur la mise la terre de l appareil consulter un lectricien qualifi ou un repr sentant technique Installation Preparation PREPARE HOT WATER LINE The line may enter from either side rear or floor within the shaded area shown e The water line may pass through the same hole as the electrical cable and drain hose Or cut an addit
19. t water supply Note Use new ferrule Do not use old parts Se i O Strain relief for electrical connection 0 O Thread seal tape Wire Nuts Strain Relief O UL Listed wire connectors 3 Thread Seal O Screw type hose clamps lape 90 Elbow Materials For New Installations Only O Air gap for drain hose if required O Waste tee for house plumbing if applicable O Electrical cable or power cord if applicable E w Elettrica Cable O Hand shut off valve recommended or Power Cord O Water line 3 8 min copper or 1 2 min plastic plastic must be tested for temperature and pressure O Coupler for extending drain line if applicable Coupler Hot Water Line TOOLS YOU WILL NEED Flat Blade Screwdriver Nut Driver Tools Required for All Installations Pe p A O Phillips head and flat blade screwdrivers A KAA rhiiips Head Screwdriver O 3 8 5 16 and 1 4 nutdrivers Safety Glasses E fa BA Cutter arpenters square SQ O Measuring tape O Safety glasses O Flashlight O Bucket to catch water when flushing the line Bucket O Tubing cutter O Gloves to protect against sharp edges O Wire strippers Wire Strippers Flashlight For New Installations Only O Drill and appropriate bits O Hole saw set P K 8 N T Hole Saw Set Gloves Measuring Tape Installation Preparation PARTS SUPPLIED Remove the hardware accessory bag and other parts from inside or taped to the
Download Pdf Manuals
Related Search