Casio CP-2070 2.4 GHz Phone
Contents
1. viewing of autodial records the LCD will time out to a blank display A FASTER WAY TO USE THE AUTODIALER If you know the autodial number 01 20 of the name and number that you wish to call you can enter it directly For example if you know that the name and number of the person you are calling are stored in autodial 06 just press AUTODIAL 6 SEND The CP 2070 will then establish a dial tone and dial the number EDITING AUTODIAL ENTRIES 1 Press PROGRAM Press the UP ARROW KEY two times or the DOWN ARROW KEY tive times or just press AUTODIAL 1 If you wish to delete all Autodial names and numbers press AUTODIAL 2 Press and hold DELETE until DELETE ALL appears in the display 3 Press DELETE again within 5 seconds to confirm All autodialer entries will then be deleted TRANSFER CALLER ID TO AUTODIAL MEMORY This feature allows you to transfer a phone number from Caller ID memory directly into the Autodial Memory This saves you time and eliminates the chance of entering an incorrect phone number into memory You can even edit the name and number before you complete the transfer Press PROGRAM The PROGRAM MODE display will flash on the screen NOTE E f you make a mistake or change your mind at any time during this procedure simply press PROGRAM again to quit Press AUTODIAL You will see 01 flashing in the lower right hand corner of the display The rest of the display may2. The T adapter allows you to connect your machine to Line 1 or Line 2 The CP 2070 will only answer one line See Accessories CLEANING THE CP 2070 CAUTION Disconnect the CP 2070 from the power outlet before cleaning Use a damp cloth or moist sponge only to clean the antenna the plastic cabinet of the handset and charging cradle and the battery charging contacts on the handset A mild soap like dishwashing detergent will help remove grease or oil Do not spray cleaners directly onto the unit Cleaners should only be used on the plastic surfaces Thoroughly dry all parts of the handset and charging cradle before re using HANDSET BATTERY INSTALLATION THIS UNIT IS SHIPPED WITH A HANDSET BATTERY PACK THAT IS NOT INSTALLED To install the battery pack 1 Press down on the battery compartment cover and slide it toward the bottom of the handset Install the new battery pack with the red wire on the right side of the black wire see drawing RED WIRE 3 Replace the battery cover by sliding it up from the bottom 4 Place the handset in the charger cradle and charge the battery pack for 12 15 hours WARNING Use only NiCd Rechargeable Battery Pack 3 6 volts 600 mAh Handset battery life 6 hours talk time 7 days standby time After several attempts the CP 2070 will not operate properly Unplug the AC ADAPTER PLUG from the back of the CP 2070 for 10 seconds Remove the battery from the handset Plug the
3. M1S1 4 00 Printed in China 5472 920 0 01 IMPORTANT FEATURES 2 4 GHz Hybrid Cordless Technology Advanced technology provides enhanced clarity and superior reception 2 4 GHz operates on a higher frequency than conventional 900 MHz telephones Caller ID If you subscribe to a Caller Identification Service available from most local telephone companies the CP 2070 can display the name and phone number of incoming calls With the Caller ID feature you can see who is calling before you answer a call Call Waiting Caller ID If you subscribe to a Call Waiting Caller ID service from your local telephone company the CP 2070 can display the name and number of an incoming call while you are already talking to another party on the cordless handset NOTE You must order the complete package that is known as CALL WAITING CALLER ID from your local telephone company If you simply order the two services of CALL WAITING and CALLER ID you may not receive Call Waiting Caller ID service Turn on Call Waiting Caller ID in programming if you subscribe to this feature otherwise leave it off Caller ID Memory The CP 2070 automatically stores the Caller ID names and numbers of the last 50 calls you have received Ultra Clear Noise Reduction Circuit Reduces background noise reception is superior to conventional cordless telephones Supertwist Nematic STN LCD Advanced LCD technology in your CP 2070 provides clear multi angle viewing o
4. AC ADAPTER back into the charging cradle and re insert the battery in the handset Return the handset to the charger cradle for 10 seconds QUESTIONS HERE S HOW TO REACH US By Phone HELPLINE 310 320 9810 Monday Friday 8 a m to 4 45 p m PST AUTHORIZED FACTORY SERVICE CENTER Phone Masters Repair Center 714 373 4233 Monday Friday 8 a m to 5 p m PST PARTS ORDERS USING A CREDIT CARD Pacific Coast Parts Distributors Inc 800 421 5080 or 310 515 0207 Monday Friday 8 a m to 4 30 p m PST On line CUSTOMER RELATIONS WEBSITE www casiocomm com E MAIL cpmicust casio com AUTHORIZED FACTORY SERVICE CENTER WEBSITE www members home net skelly1 PM1 htm E MAIL phonemasters hotmail com PARTS AND ACCESSORIES WEBSITE www pacparts com E MAIL orders pacparts com AUTHORIZED FACTORY SERVICE CENTER For repairs please bring or send your unit to Phone Masters Repair Center 11899 Valley View Street Garden Grove CA 92845 1 Pack your product securely in a sturdy shipping box 2 Include a clear and specific explanation of the problem 3 Include your name street address sorry no P O box and daytime phone number Provide a legible photocopy of the dated store receipt for one year warranty purposes Design and specifications are subject to change without notice CASIO COMMUNICATIONS INC 20665 Manhattan Place Torrance CA 90501 1827 Internet Website http www casiocomm com
5. IN USE INDICATOR The handset in Use Indicator located on the charging cradle will light solid whenever the CP 2070 is in TALK mode MOVING THE CP 2070 Unplug the CP 2070 from the wall outlet if you wish to move the unit Place the handset in the charging cradle after relocating the CP 2070 This will reset the CP 2070 s security code All autodial Caller ID and redial numbers will be saved POWER FAILURE NON VOLATILE MEMORY The CP 2070 s memory backup system maintains up to 20 autodial names and numbers and stored Caller ID information up to 50 records indefinitely until you erase them This non volatile memory does not require battery power MULTI LINE INSTALLATION Installations with more than two lines such as business PBX or Key Systems may require a separate RJ11 jack for answering machines Please contact your telephone equipment provider for additional information See Accessories TROUBLESHOOTING The handset does not ring Check the ringer switch on the side of the handset and make sure it is not set to OFF Check AC adaptor and telephone cord connection at the charging cradle and wall outlet Was the battery pack charged for at least 12 15 hours Does Low Battery appear on the display Line Error Message The Line Error message may occasionally appear due to electrical static on the telephone line This is normal However if you consistently see this
6. OFF Su CP 2070 es empacado con los interruptores para el timbre en la base y el auricular en la posici n encendido ON A su gusto usted puede tener apagados o encendidos los timbres de su CP 2070 ilMPORTANTE CARGUE COMPLETAMENTE LA PILA DEL AURICULAR DE 12 A15 HORAS ANTES DE USAR EL TELEFONO El desempe o de la pila es determinado por la duraci n del primer ciclo de carga Si usted se precipita a usar su tel fono antes de que la pila haya cargado completamente usted reducir el tiempo efectivo de uso por carga de su tel fono Instale la pila y conecte el tel fono como se muestra luego coloque el auricular en la base para cargar con las teclas de n meros hacia abajo El INDICADOR DE CARGA CHARGE INDICATOR en la base se encender Deje el auricular en la base de 12 a 15 horas
7. as evidence of the purchase date See Troubleshooting section above for details Before returning or exchanging your product call the CASIO COMMUNICATIONS Helpline at 310 320 9810 CP 2070 CALL WAITING CALLER ID This unit is not shipped with the handset battery installed Please install and charge the handset battery pack before initial setup and use 1 PLUG the CP 2070 s telephone cord into a telephone wall jack PLUG the other end of the cord into the back of the base unit PULSE TONE CONNECT the AC Adapter Plug into the AC Adapter Outlet on the back of the CP 2070 charging cradle LOOP the cord through the AC Adapter Cord Holder to prevent accidental disconnection PLUG the AC Adapter into an electrical wall outlet Place the handset with battery pack installed in the cradle 4 It may be necessary to set the TONE PULSE SWITCH CASIO 2 4 GHz CORDLESS PHONE WITH EASY TO USE OWNER S GUIDE ie Open for easy operating guide Raise the charging cradle antenna for clear reception REFERENCIA RAPIDA INSTALACI N 1 ENCHUFE el cord n de su CP 2070 en un enchufe para tel fono en la pared ENCHUFE l otro extremo del cord n telef nico en la parte posterior de la unidad base CONECTE el enchufe del adaptador de CA en la entrada de tomacorriente para adaptador de CA que hay en la parte de atr s de la base para carga de su CP 2070 ENGANCHE el cord n en el sujetador de cord n para
8. digit for you automa tically whenever you dial a stored Caller ID number This may be useful if you use your CP 2070 at a business that uses a PBX telephone system 1 Press PROGRAM Press the UP ARROW KEY four times The Outside Line display will appear Use the LEFT or RIGHT ARROW KEY to select a digit 4 Press PROGRAM again to finish PROGRAM OPTION 5 CALL WAITING CALLER ID The Call Waiting Caller ID option is factory preset to OFF If you subscribe to Call Waiting Caller ID you should set this option to ON otherwise leave it off 1 Press PROGRAM Press the UP ARROW KEY tive times The Call Waiting Caller ID Option display will appear Use the LEFT or RIGHT ARROW KEY to turn this option ON or OFF 4 Press PROGRAM again to finish PROGRAM OPTION 6 ON SCREEN HELP Two modes of on screen help are available while you program the CP 2070 These are 1 Automatic Help A help message will automatically scroll across the screen whenever you wait 15 seconds without pressing a key If you do not wish to wait 15 seconds you can always see the help message immediately by pressing the SEND key SEND key Help The help messages with the exception of the initial message will not appear unless you press the SEND key NOTE E In either mode you can stop the help message at any time by pressing any key TO CHANGE THE HELP OPTION 1 Press PROGRAM Press the UP ARROW KEY six t
9. evitar una desconexi n accidental ENCHUFE el adaptador de CA en un 3 tomacorriente el ctrico de pared Coloque el auricular con su paquete de pilas ya instalado en la unidad base para carga Puede que se necesite ajustar el 4 interruptor selector para modo de operaci n TONOS o de PULSOS Saque y extienda completamente la 5 antena en la base para carga para lograr la mejor recepci n USO EN PARED O ESCRITORIO Se incluye un soporte para empotrado en pared si se desease Enrolle en forma apretada el cord n telef nico al rededor de las cuatro gu as en la parte interior del soporte para empotrado Haga pasar el cord n telef nico a trav s del orificio en el centro del soporte Vea el dibujo El auricular puede ser cargado en la posici n mirando hacia afuera o boca abajo a n si se ha empotrado en la pared INTERRUPTOR SELECTOR TONOS PULSOS Este interruptor le indica a su CP 2070 que la marcaci n de n meros es a trav s de tonos o por pulsos de acuerdo al tipo e servicios que tenga de su compa a de servicios telef nicos Su CP 2070 es empacado con el interruptor TONE PULSE Tonos Pulsos en la posici n para operaci n por tonos TONE Si usted no tuviera servicio telef nico por tonos cambie el interruptor a la posici n PULSE Pulsos en la parte posterior de la base para carga TONE para servicio telef nico por tonos PULSE para servicio telef nico por pulsos TIMBRE ENCENDIDO APAGADO ON
10. instructions Do not open or mutilate the battery Released electrolyte is corrosive and may cause damage to the eyes or skin It may be toxic if swallowed Exercise care when handling the battery in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause burns CONTAINS NICKEL CADMIUM RECHARGEABLE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY SAVE THESE INSTRUCTIONS li CONSERVEZ CES DIRECTIVES Blocked and Unavailable Messages If a caller chooses to partially or completely block Caller ID information a message will appear on the display indicating that the name and or phone number has been blocked If for any other reason the name and or number information is currently not available from your local phone company an Unavailable message will appear on the display The time and date information for the call will be recorded into the CP 2070 s memory Local Area Code Setting If you live in a 7 digit dialing area and you program your local area code into the unit the CP 2070 can make returning phone calls easier by automatically dialing stored Caller ID numbers If you live in a 10 or 11 digit dialing area leave this setting at 000 Call Waiting Caller ID does not work 1 You must subscribe to the combined package service Call Waiting Caller ID from your local telephone company to use this feature Simply subs
11. or static interference Move closer to the charging cradle to deactivate the alarm and prevent disconnection If you remain out of range for too long the CP 2070 will disconnect from the line If the handset loses its security code you will also hear an alarm tone To reset this security code place the handset in the charging cradle for a few seconds Pick up the handset and try your call again Interference from other appliances may also cause the alarm to sound To prevent interference move the charging cradle to another location and raise its antenna 1 Once you hear the confirmation tone you can press TALK to answer the call and automatically retain all the Caller ID information received NOTE E f you press TALK before you hear the Caller ID confirmation tone the Caller ID information for that call will be lost ANSWERING CALL WAITING CALLER ID CALLS If you subscribe to a Call Waiting Caller ID service with your telephone company and you program Call Waiting Caller ID to ON the CP 2070 can receive a Caller ID call while you are on the line with another party 1 If a second call comes while you are on the phone your CP 2070 will beep You can now view the LCD screen to see the name and number of the incoming caller You can decide whether to answer the second call or ignore it and continue with the first call If you choose to take the second call press FLASH to answer it 4 You may continue to pr
12. state tariffs Contact your state public utility commission or corporation commission for information Jack RJ11 Ringer Equivalence See bottom underside of the CP 2070 base unit CASIO COMMUNICATIONS Inc 20665 Manhattan Place Torrance CA 90501 NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Any changes made by the user not approved by CASIO COMMUNICATIONS can void the user s authority to operate the equipment This prod
13. wall outlet is still supplying power to the unit when you leave the room Leave the wall outlet switch on if necessary Optimize the 2 4 GHz Cordless Performance For maximum distance and noise free operation place the base unit away from electrical appliances Place the base unit in a central location with no obstructions such as walls If you experience interference while using the handset near other electrical appliances or other cordless phone base units move away from the electrical appliance or other cordless phone base units and closer to the CP 2070 base unit Digital Security Code The Digital Security Coding System automatically resets a new personal security code to one of over 64 000 combinations every time you return the CP 2070 handset to the base unit Whenever the handset is returned to the base unit you will hear a beep The security code prevents unauthorized use of your telephone line false rings and false dialing FCC REQUIREMENTS USER INSTRUCTIONS This equipment complies with Part 68 of the FCC rules On the bottom of this equipment is a label that contains among other information the FCC registration number and Ringer Equivalence Number REN for this equipment If requested provide this information to your telephone company The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called In most but not all are
14. ID NUMBERS The CP 2070 allows you to place calls using stored Caller ID information Press CALLER ID You may press TALK first if you wish Caller ID can be dialed from off hook mode or on hook mode Locate the desired numbers by scrolling through saved Caller ID information using the DOWN or UP ARROW KEY Holding down the DOWN or UP ARROW KEYS will automatically fast scroll through Caller ID records 3 Press SEND 4 If your area code is set to 000 in the CP 2070 the LCD will display the first of the three different dialing options Press the UP or DOWN ARROW KEY to view the rest of the dialing option 5 Select one of the three dialing options and press SEND again The CP 2070 will automatically establish a dial tone and place the call NOTES E f you have programmed your local area code into the CP 2070 before using this feature then the CP 2070 will not prompt you for different dialing options See Programming the CP 2070 for more information E f no button is pressed for 30 seconds during viewing of Caller ID information the LCD will time out to a blank display DELETING INDIVIDUAL CALLER ID ENTRIES Specific Caller ID entries may be deleted 1 Press CALLER ID Press the DOWN or UP ARROW KEY to locate the entry you wish to delete Press and release DELETE You will hear a double beep and the Delete message will appear 4 Press DELETE again within 5 seconds to confirm The e
15. INITIAL SETUP WALL DESK USE A wall mount bracket is included and can be installed if needed Tightly coil the telephone cord around the four guides on the inside of the wall mounting bracket Pull the telephone cord through the center opening on the wall mounting bracket Refer to the drawing The handset can be charged face out or face down even when wall mounted TONE PULSE SWITCH This switch tells the CP 2070 to dial out with either touchtone or pulse signals to match the service you have with your local telephone company The CP 2070 is shipped with the TONE PULSE SWITCH in the TONE position If you do not have touchtone service set the switch to pulse on the back of the charging cradle TONE for Touchtone systems PULSE for Rotary dialing or Pulse systems PULSE TONE RINGER ON OFF The CP 2070 is shipped with the handset RINGER ON OFF SWITCH in the ON position and the base RINGER OFF LOW HIGH SWITCH in the HIGH position You can independently set the ringers of the CP 2070 STANDBY MODE The CP 2070 is in Standby mode whenever it is idle waiting for a call If the handset is in the charging cradle the display will either be blank If you have new caller ID entries from recent unanswered calls it will show the NEW CALLERS message with the number of new callers at the lower far right of the display screen Press CALLER ID to view the names and numbers of New Callers NOTE E f the
16. Ne pas utiliser l appareil pr s de l eau par exemple pr s d une baignoire d un lavabo d un vier de cuisine d un bac laver dans un sous sol humide ou pr s d une piscine viter d utiliser le t l phone pendant un orage lectrique sauf s il s agit d un appareil sans fil Ceci peut pr senter un risque de choc lectrique caus par la foudre Ne pas utiliser l appareil t l phonique pour signaler une fuite de gaz s il est situ pr s de la fuite Utiliser seulement le cordon d alimentation et le type de piles indiqu s dans ce manuel Ne pas jeter les piles dans le feu elles peuvent exploser Se conformer aux r glements pertinents quant l limination des piles CAUTION ATTENTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equiva lent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Il y a danger d explosion s il y a remplacement incorrect de la batterie Remplacer uniquement avec une batterie du m me type ou d un type quivalent recommand para le constructeur Mettre au rebut les batteries usag es conform ment aux instructions du fabricant 1 Use batteries only intended for recharging Use only the following battery pack GP60AAS3BMJ Nickel Cadmium Rechargeable 3 6 volts 600 mAh Do not dispose of the battery in a fire The cell may explode Check with local codes for special disposal
17. accomplished with a factory reconditioned unit This limited warranty does not apply a to any product damaged by accident misuse improper line voltage lightning fire water or other acts of nature b if the product is altered or repaired by anyone other than CASIO COMMUNICATIONS INC or one of its authorized warranty stations or c if the FCC approved connector plugs are removed This limited warranty does not cover broken or marred cabinets Except to the extent prohibited by applicable law all implied warranties made by CASIO COMMUNICATIONS in connection with this product are limited in duration to a period of one 1 year from the date of original purchase and no warranties whether expressed or implied shall apply to this product after said period Should this product prove defective in workmanship or material the consumer s sole remedies shall be such repair or replacement as is herein above provided Under no circumstances shall CASIO COMMUNICATIONS be liable for any loss or damage direct consequential or incidental arising out of the use of or inability to use this product Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusion may not apply to you In order to obtain warranty service you must provide evidence of purchase date For your convenience keep the dealer s dated bill of sale or delivery ticket
18. as the sum of the RENs of all devices should not exceed five 5 0 To be certain of the number of devices you may connect to your line as determined by the REN you should call your local telephone company to determine the maximum REN for your calling area If your answering machine causes harm to the telephone network the telephone company may discontinue your service temporarily If possible they will notify you in advance But if advance notice is not practical you will be notified as soon as possible You will be advised of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operations or procedures that could affect the proper operation of your equipment If they do you will be given advance notice so as to give you an opportunity to maintain uninterrupted service If there is a problem with this unit the telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning Repairs can only be made by the manufacturer or an authorized service agency Unauthorized repairs void registration and warranty Contact seller or manufacturer for details of permissible user performed routine repairs and where and how to have other than routine repairs made This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to
19. ck of the handset ACCESSORIES To order accessories to check on parts availability or to order parts using a credit card call 800 421 5080 or 310 515 0207 Monday Friday 8 a m to 4 30 p m PST To order on line www pacparts com E MAIL orders pacparts com Lightning Arrestor Helps protect telephone devices from damage caused by lightning strikes to the telephone line Recommended for areas prone to electrical storms Rechargeable Battery Pack For Model CP 2070 AC Adapter For Model CP 2070 Modular Duplex T Adapter Converts a single modular telephone jack to a double jack Modular Two Line T Adapter Splits one RJ14 two line jack into two RJ11 single line jacks Headset over ear Headset over head Belt Clip LIMITED WARRANTY IMPORTANT SALES SLIP OR EVIDENCE OF PURCHASE DATE REQUIRED This limited warranty gives you specific legal rights you may also have other rights which vary from state to state The limited warranty is extended only to the original consumer of a CASIO COMMUNICATIONS product and is valid only with respect to consumers within the United States of America and Canada Should this product prove defective by reason of improper workmanship or material during the period of one 1 year from the date of original purchase CASIO COMMUNICATIONS will repair or at its option replace the product without charge for parts or labor If CASIO COMMUNICATIONS elects to replace the product such replacement may be
20. cribing to Call Waiting and Caller ID may not be sufficient to receive incoming Caller ID information while you are on the line Turn the CP 2070 s Call Waiting Caller ID option on LINE IN USE INDICATOR lights yet the handset or extension phone are not in use The telephone cord is not properly plugged in Connect one end of the telephone cord to the wall jack and connect the other end of the telephone line cord to the back of the CP 2070 No sound from the handset Check the VOLUME CONTROL It may have been programmed to a low level No Dial Tone is heard when calling out 1 Was the battery pack charged for at least 12 15 hours Does Low Battery appear on the display Check the AC adaptor and telephone cord connection at the charging cradle and wall outlet Check the connection of the battery pack ADDITIONAL INFO HANDSET CHARGING INDICATOR The HANDSET CHARGING INDICATOR lights solid when the handset is placed in the charger Place the handset in the charger for 12 15 hours before the first use or when the battery begins to run low LINE IN USE INDICATOR The LINE IN USE INDICATOR located on the charging cradle will light solid whenever the CP 2070 is in TALK mode whenever any other extension telephone on the same line is being used or whenever the telephone cord is not properly plugged into the wall jack or telephone It will flash slowly whenever the CP 2070 is in hold mode HANDSET
21. d Press the UP ARROW KEY to move the cursor to the name field Enter the name using the keypad Pressing a key once displays the first upper case letter on that key Pressing it repeatedly will cycle through all of the upper and lower case characters on that key Stop when the desired character appears in the display The 1 key provides unique characters and icons 7 Press the RIGHT ARROW KEY to move the cursor one space to the right 8 Press AUTODIAL again when you finish to save the new entry Nothing will be stored until the AUTODIAL key is pressed 0O o1 A 9 Press PROGRAM to exit the mode PROGRAM MING PAUSES IN AUTODIAL When you are programming numbers into the autodialer the HOLD PAUSE key can be used to insert a two second pause wait period between digits For example if you need to dial a 9 in order to obtain an outside line you can use the PAUSE key to insert a two second pause for the second dial tone Just press 9 PAUSE HOLD and then the number you wish to program AUTODIAL Press the LEFT or RIGHT ARROW KEY to locate the number you wish to edit Press the UP ARROW KEY The entire phone number will flash When the entire phone number is flashing entering a number on the keypad will erase the previously stored phone number from the display and replace it 5 If you only wish to change a few digits press the LEFT ARROW KEY to activate the cursor and th
22. e battery discharges the stack symbols will disappear starting from the right When the battery is low the display will look like BATTERY ms 2 Press BATTERY again or wait a few seconds to leave battery condition mode NOTES E Charge the battery for 12 15 hours before using E f BATTERY is pressed while the handset is in the cradle CHARGING will appear in the LCD LOW BATTERY INDICATOR The CP 2070 will automatically detect a low battery If this happens you will hear a double beep and the LOW BATTERY display will appear If the Low Battery indicator appears while you are talking on the CP 2070 you may only have a few minutes left before the battery discharges completely in which case you will be disconnected To prevent this simply pick up an extension phone and place the CP 2070 back in the charger Place the handset in the charger for 12 15 hours to recharge the battery NOTE E The battery can be recharged many times but if you get a low battery indication even after 12 15 hours of charging you should replace the battery pack See the Accessories order form to purchase a battery pack OUT OF RANGE ALARM The CP 2070 cordless handset operates like any other cordless handset You can use it in the yard at the pool at the mailbox or any place within the operating range of the charging cradle If you move out of the charging cradle s operating range you may hear a triple beep warning tone and
23. en use the RIGHT or LEFT ARROW DELETE and NUMBER keys to make changes 6 Press the UP ARROW KEY The entire name will now flash As in the previous step entering a number key for a character entry at this point will erase the flashing name from the display and replace it 7 If you only wish to change a few letters press the RIGHT ARROW KEY to activate the cursor and then use the RIGHT or LEFT ARROW DELETE and NUMBER keys to make changes 8 Press AUTODIAL once the correct information is entered and your changes will be saved Press PROGRAM to exit the programming mode ERASING AUTODIAL NAMES AND NUMBERS To erase numbers in autodial press AUTODIAL Press the DOWN or UP ARROW KEY to find the autodial name and number you wish to erase Press and release DELETE DELETE will appear in the display 4 Press DELETE again within 5 seconds to confirm The entry will then be deleted ERASING ALL AUTODIAL USING AUTODIAL NAMES AND NUMBERS Press AUTODIAL You may press TALK first if you wish Autodial can be dialed from off hook mode or on hook mode If phone numbers are programmed into the autodial memory the first programmed number will appear in the display 2 Press the DOWN or UP ARROW KEY to select an autodial number 3 When you locate the number press SEND to dial it The CP 2070 will automatically dial the number on the display NOTE E f no button is pressed for 30 seconds during
24. ess FLASH to switch between the two calling parties indefinitely SAVING CALLER ID INFORMATION The CP 2070 automatically saves up to 50 Caller ID entries Any Caller ID information name phone number date time that is transmitted will be stored for your reference or use in the autodialer and redial memory All Caller ID names and numbers are stored in reverse order of receipt last call is displayed as highest memory number If the memory becomes full the newest entries will be saved and the oldest ones will be erased RECEIVING CALLER ID INFORMATION IF CALL IS NOT ANSWERED Even if Caller ID calls are not answered the CP 2070 will automatically store the Caller ID information into memory If the handset is in the charger NEW CALLERS will appear on the display This message will stay on the screen and go away after you review the stored Caller ID information The NEW CALLS count in the LCD indicates all CPID records not yet viewed The NEW CALLS INDICATOR on the base will light until you have pressed the Caller ID button to review stored Caller ID records NOTE E f the handset is out of the cradle the LCD screen will only say lt NEW CALLERS gt for 5 seconds and then go blank It will say lt NEW CALLERS gt again if put back into the charging cradle REVIEWING STORED CALLER ID INFORMATION If you received calls while you were away from your CP 2070 you can retrieve the stored Caller ID e
25. f caller s name and phone number if you subscribe to Caller ID service from your local telephone company Autodial Memory Backup CASIO s memory backup system maintains up to 20 autodial names and numbers indefinitely until you erase them This non volatile memory does not require battery power Charging The Battery Charge the battery for 12 15 hours before using the cordless handset for the first time The handset is always charging while it is in the charging cradle and cannot be overcharged To charge the battery first check the AC Adapter to see that it is connected correctly Then place the handset in the charging cradle The CHARGING INDICATOR on the charging cradle lights solid to indicate that the CP 2070 is charging Local Area Code Setting If you are planning to use the Caller ID features on the CP 2070 and you reside in a 7 digit dialing area you may want to program your local area code into the handset s memory after you have charged the battery for the first time The CP 2070 uses this information to automatically dial stored Caller ID numbers correctly from a 7 digit dialing area If you have 10 or 11 digit dialing in your area leave the area code setting at 000 The CP 2070 will prompt you to choose between 7 10 or 11 digit dialing each time you make a caller ID call Headset Jack Belt Clip Included The CP 2070 handset has a 2 5mm jack for attachment of a headset headset not included The belt clip snaps into the ba
26. handset is in Standby Mode but not in the charging cradle the display will go blank after a short time to conserve battery power TO PLACE A CALL d Pick up the handset and press TALK The following display will be briefly shown This display indicates that the handset is estab lishing contact with the charging cradle A dial tone will be established In this 2 example CH03 is the current channel number of 60 available channels in your area Wait for dial tone and dial the phone number The number will appear in the display as you dial UME ME ni vu A L CHOS NOTE E The HANDSET LINE IN USE INDICATOR on the charging cradle lights solid to show the handset is in use TO END A CALL 1 To hang up press TALK or return the handset to the charging cradle NOTE E When you return the handset to the charging cradle you are hanging up the phone and returning to Standby Mode The CP 2070 is now ready to receive a call and the CHARGING INDICATOR lights solid to show that the battery is charging IF YOU MISDIALED A NUMBER Press TALK twice off and on Wait for dial tone and dial the correct number TO RECEIVE A CALL When the phone rings pick up the cordless handset and press TALK You will briefly see the SCANNING CHANNELS display followed by the VOLUME display Speak to the caller 2 To hang up press TALK on the handset or return the handset to the charg
27. ime out NOTE E The Call Timer will not be disrupted if HOLD is pressed The Hold timer 5 minute count down timer will display and the Call Timer will continue hidden from view during any Hold mode DIALING A NUMBER USING THE SEND KEY DISPLAY amp DIAL Send Key Dialing is extremely reliable because you can see the number you have entered before actually dialing it Make sure the CP 2070 is in Standby Mode Without pressing the TALK button enter the number you wish to dial If you make a mistake use DELETE to make changes The last digit entered will be deleted Each time DELETE is pressed the previously entered digit will be erased After you have correctly entered the entire number you wish to dial press SEND The CP 2070 will dial the number REDIAL The CP 2070 remembers the last number you dialed The redial memory will hold up to 32 digits Every time you dial a new telephone number the redial memory is updated with that new number 1 Press TALK and wait for a dial tone 2 Press REDIAL REDIAL WHEN BUSY If you receive a busy signal after placing a call and you wish to try again immediately there is no need to hang up the phone 1 Press REDIAL while hearing a busy signal and the CP 2070 will automatically hang up reconnect and dial the number again DISPLAY REDIALING Display Redialing allows you to view the contents of the redial memory before dialing This is useful if you aren t su
28. imes The Help display will appear Use the LEFT or RIGHT ARROW KEY to switch between the two help modes 4 Press PROGRAM again to finish IMPORTANT CORDLESS TELEPHONE INFORMATION INTERFERENCE INFORMATION Notice This cordless telephone uses radio communications between the handset and the base unit and may not ensure privacy of communication Other devices including other cordless telephones may interfere with the operation of this cordless telephone or cause noise during operation Cordless telephone equipment generates and receives radio waves and if not installed and used properly may pick up interference To prevent interference Avoid locations such as heating appliances electrical equipment e g fluorescent lamp TV radio refrigerator computer places subject to direct sunlight excessive dust moisture vibration etc Locate the base unit in a high place in the house such as the second floor in order to receive the most effective communication range Fully extend the base unit antenna Telephones must not cause interference to any licensed radio service Charge the Handset Battery Before Using the Cordless Telephone The battery loses its charge during shipping and storage Be sure to charge the battery before you use the CP 2070 cordless telephone Place the handset in the base unit The CHARGING INDICATOR on the base will light Leave the handset in the base unit for 12 15 hours Remember to make sure that the
29. ing cradle CALLER ID SERVICE OPTIONS You must subscribe to a Caller ID service available from most local telephone companies in order to receive Caller ID information Most Caller ID services offer the following two options 1 Standard Caller ID with name and number The name phone number and local time if available of the incoming call are received after your phone rings 2 Call Waiting Caller ID with name and number The name phone number and local time if available of the incoming call are received after your phone rings If you are on the phone and receive another call you will hear a tone telling you there is a call waiting The Call Waiting Caller ID information will appear on the display HANDSET TELEPHONE OPERATION HANDSET VOLUME CONTROL Whenever the CP 2070 is in Talk mode the handset volume will be displayed 1 Press the DOWN or UP ARROW KEY to adjust the volume during a call The volume will remain at that level for your next call CALL TIMER About 10 seconds after you enter Talk mode a Call Timer will appear on the display The timer will automatically be reset whenever you place a new call NOTES E The length of time shown on the display is intended only to be an estimate duration of a phone call CASIO makes no guarantees regarding the accuracy of this timer E The Call Timer will not be disrupted if HOLD is pressed The Hold timer 5 minute count down timer will display and
30. l Waiting Caller ID 6 On Screen Help NOTE E f no button is pressed for 30 seconds during programming functions the LCD will time out to a blank display PROGRAM OPTION 1 RINGER TONE You can select one of 4 ringer tones for the CP 2070 1 Press PROGRAM 2 Press the UP ARROW KEY once The words RINGER TONE and its current setting 1 4 will be displayed Press the LEFT or RIGHT ARROW KEYS to select a ringer tone The CP 2070 will ring once to confirm the tone you have selected 4 Press PROGRAM again to finish PROGRAM OPTION 3 LOCAL AREA CODE SETTING The CP 2070 can make returning phone calls easier for users who reside in a 7 digit dialing area by automatically dialing stored Caller ID numbers In order for this feature to work correctly it is necessary to program your local area code into the unit 1 Press PROGRAM 2 Press the UP ARROW KEY three times The Area Code program display will appear 000 is the factory default setting 3 Use the keypad to enter the three digits of your local area code 4 Press PROGRAM again to finish If you have the 10 or 11 digit dialing system in your area leave the area code setting at 000 The CP 2070 will prompt you to choose between 7 10 or 11 digit dialing each time you make a caller ID call PROGRAM OPTION 4 OUTSIDE LINE If your telephone system requires that you enter an extra digit in order to obtain an outside line the CP 2070 can dial this
31. message when you should be receiving Caller ID data i e between the first and second rings you may have a problem with your phone line Contact your local telephone company You hear continuous short beeps instead of a dial tone when using the cordless handset The beep tones are a warning alarm to let you know 1 That the handset is out of communication range with the charger cradle Move the handset closer to your charger cradle That the charger cradle had some problem like a power failure Return the handset to the charger cradle for 5 seconds and make sure all cords are connected correctly Interference Noise is heard 1 The handset is too far from the charger cradle 2 The cordless handset is picking up interference from one of several sources electrical appliances such as radio TV fluorescent lights etc Move the charger cradle to reduce interference 3 Press CHANNEL to select another channel 4 Raise the charging cradle antenna No Page Tone is heard at the Handset 1 Check the AC ADAPTER and telephone cord connection 2 You may have had a power failure Return the handset to the charger cradle for 5 seconds to reset the Digital Security Code A beep is heard each time the handset is returned to the charger cradle This is normal operation The handset is updating the security code TWO LINE INSTALLATION Two line installations may require a two line T adapter for the CP 2070 to operate correctly
32. ntries from memory CPID records can also be viewed and scrolled while off hook while you are on an active call 1 Press CALLER ID The entry for the most recently received call will be displayed The name will be displayed on the top line the number on the second line and the time and date of that call will be displayed on the third line of the display all information is displayed at once The word NEW indicates that this is a new caller ID record The word NEW will be displayed for each record that is being viewed for the first time The two digit number example 22 in the lower right corner of the display indicates that N Johnson is your most recent caller and it is your twenty second call This helps you keep track of how many entries are currently stored in your CP 2070 Use the DOWN or UP ARROW KEY to see the other entries DOWN scrolls through older records and UP scrolls the opposite direction BLOCKED AND UNAVAILABLE MESSAGES If a caller chooses to partially or completely block Caller ID information a message will appear on the display indicating that the name and or phone number has been blocked If for any other reason the name and or number information is currently not available from your local phone company an Unavailable message will appear on the display The time and date information for the call will still be recorded into the CP 2070 s memory DIALING STORED CALLER
33. ntry will then be deleted DELETING ALL CALLER ID INFORM ATION 1 Press CALLER ID 2 Press and hold DELETE until you see the Delete All message appear on the display Press DELETE again within 5 seconds to confirm All Caller ID entries will then be deleted USING THE CORDLESS PHONE WITHOUT CALLER ID If you do not subscribe to a Caller ID service you can still benefit from most of the CP 2070 s advanced features However you should be aware of the following 1 Pressing CALLER ID will simply display the NO CALLS message 2 The Call Waiting Caller ID and Outside Line program options will have no effect NOTE E Certain sounds and voice pitches may occasionally cause the CP 2070 to incorrectly think that the local phone company is sending Call Waiting Caller ID information Although no Caller ID data will show up on the display the CP 2070 may mute the phone line for a second or so To prevent this annoyance simply make sure that the Call Waiting Caller ID program option is set to OFF STORING NAMES AND NUMBERS IN AUTODIAL You may store up to 20 of your most frequently dialed names and numbers into the autodial memory Autodial names can be up to 16 characters long and the accompanying phone numbers can be up to 24 digits each 1 Press PROGRAM 2 Press AUTODIAL Press the LEFT or RIGHT ARROW KEY to locate a memory location Enter a telephone number on the keypa
34. or may not be blank depending on the current contents of location 1 3 Use the LEFT or RIGHT ARROW KEY to select the autodial location where you wish to transfer the Caller ID number Again the rest of the display may or may not be blank If it is not blank the contents of this location will be written over once you complete the transfer 4 Press CALLER ID The most recently received Caller ID entry will appear in the display 5 6 Use the DOWN or UP ARROW KEY to TRANSFER REDIAL NUMBER select the Caller ID entry you wish to save TO AUTODIAL MEM ORY This feature allows you to transfer a phone number from the Redial Memory directly into the Autodial Memory If you wish you can add a name before you complete the transfer Follow steps 1 3 under TRANSFER CALLER ID TO AUTODIAL MEMORY Press REDIAL The contents of the Redial Memory will appear in the display You can either save the entry exactly as it appears or you can edit the name and or number To save the entry without any editing just press AUTODIAL To edit the entry press the UP ARROW KEY and proceed as described in the TO EDIT AUTODIAL ENTRIES section When you are finished press PROGRAM to exit Progen mere Follow steps 6 7 under TRANSFER CALLER ID TO AUTODIAL MEMORY to edit and save your autodial entry PROGRAM MING THE CP 2070 PROGRAMMING OPTIONS Ringer Tone Autodialer see section E Local Area Code Setting 4 Outside Line 5 Cal
35. re what number was last dialed on the CP 2070 Make sure the unit is in Standby mode Press REDIAL You will be able to view the last 15 digits of the last number dialed 2 Press SEND to dial PAGING THE HANDSET FROM THE CHARGING CRADLE d Press PAGE on the charging cradle The base unit will issue beeps to confirm that the paging signal to the HS has been enabled You will hear the handset ring 2 To cancel the page either press PAGE again or TALK twice on the handset or place the handset in the charging cradle NOTE E After seven rings the page will stop CALL WAITING amp CALLER ID NOTE The display illustrations in the remainder of this section are presented with the assumption that your Caller ID service provides both name and number If you have a number only service the name will be blank ANSWERING CALLER ID CALLS When you receive a call the CP 2070 will receive the Caller ID information from your phone company within the first two rings Caller ID information will display even if the ringer is set to off When all of the data is received you will hear a low high confirmation tone and the Caller ID information will appear on the display BATTERY CONDITION You can check the power level of the battery to avoid battery depletion Press BATTERY when the handset is out of the charging cradle The following display will appear when the battery is fully charged BATTERY ws m m i i As th
36. the Call Timer will continue hidden from view during any Hold mode LAST CALL TIME DISPLAY 1 Press the RIGHT ARROW CHANNEL KEY to view the approximate length of the last call after you have hung up the phone CHANGING CHANNELS MANUALLY After TALKis pressed the CP 2070 selects the best of 60 available channels in your area If you hear noise or interference while using the CP 2070 press CHANNEL on the handset to change channels FLASH CALL WAITING If you subscribe to a call waiting service and you receive another call while using the phone press FLASH to answer the second call To return to the first call press FLASH again FLASH may also be used on a business phone system CENTREX PBX for transferring calls HOLD You may place a call on hold while using the cordless handset 1 Press HOLD to place a call on hold The LINE IN USE INDICATOR will flash slowly NOTE W You can place a call on hold for up to 5 minutes During HOLD do not return the handset to the charging cradle Doing so will disconnect the caller To continue your phone conversation 2 press TALK HOLD or pick up an extension phone connected to the same line When the extension phone is picked up the CP 2070 automatically disconnects itself from the line Extension phone pick up during HS Hold mode will discontinue the Hold mode connect the call to the new extension phone and cause the CP 2070 to go idle after a 10 second display t
37. uct is hearing aid compatible IMPORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS Never install telephone wiring during a lightning storm Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface Use caution when installing or modifying telephone lines IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning Do not use the telephone to report a gas leak in the vicinity of the leak Use only the power cord and batteries indicated in this manual Do not dispose of batteries in a fire They may explode Check with local codes for possible special disposal instructions IMPORTANTES MESURES DE SECURITE Certaines mesures de s curit doivent tre prises lors de l utilisation de mat rial t l phonique afin de r duire les risques d incendie de chocs lectriques et de blessures En voici quelques unes 1
Download Pdf Manuals
Related Search