Home

JVC HR-VP693U VCR

1. On the Remote El Press SP EP during playback to activate manual tracking E Press CH to eliminate the noises Press it briefly for a fine adjustment or press and hold for a coarse adjustment Press SP EP again to reactivate automatic tracking On the VCR Hl Press CH and simultaneously during playback to activate manual tracking H Press CH or to eliminate the noises Press it briefly for a fine adjustment or press and hold for a coarse adjustment Press CH and simultaneously again to reactivate automatic tracking Selecting monitor sound Audio Monitor While playing back a tape on which stereo sound or SAP sound is recorded press A MONITOR on the Remote Each time you press the button sound changes HI Fl Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back NORM HI FI Both sounds on the Hi Fi track and normal track are mixed and played back NOTE The above indication appears when SUPERIMPOSE is set to ON though the monitor sound changes in sequence Automatic operations after rewinding Next Function Memory The Next Function Memory tells the VCR what to do after rewinding is complete Ensure that the VCR is in stop mode For Automatic Playback Start Press REW lt lt then press PLAY B gt withi
2. THEN OK PRESS MENU TO END GUIDE CHANNEL SET GUIDE CH gt amp El Input receiving channel number Press AV or the Number keys to select the number of the channel on which the CALE guide channel s broadcasts are received then press OK or gt PRESS NUMBER KEY 0 9 OR 4 THEN OK Repeat steps E and B for each instance Press MENU TO END E Return to normal screen Press MENU on the Remote Timer Recording VCR Plus Timer Programing The PlusCode programing numbers are the numbers next to the program in most TV listing Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically El Press PROG on the Remote to access the PlusCode No screen PLUSCODE NO PRESS NUMBER KEY 0 9 PRESS TO SET XPRESS PROGRAMMING PRESS PROG TO END AS HI Press the appropriate Number keys to input the PlusCode number then press OK Check to make sure the setting is accurate on the Program screen PROGRAM 1 PLUSCODE N ESE No Ms ae8 7 1234567 sE S 8 00PM gt 1200PM 12 24 00 12 SP SUN PRESS 8 DAILY 9 WEEKLY PRESS NUMBER KEY 0 9 THEN OK STOP STOP TIME SP EP PRESS PROG TO END PRESS PROG TO END If the Guide Channel Set screen appears after pressing OK press the GUIDE CH s12 Number keys CH or AV to ER CH ian input the number of the channel on which the broadcast for the PlusCode _ yppess NUMBER E
3. The timer recording standby mode is automatically engaged when the VCR is turned off It is temporarily canceled when the VCR is turned on You do not have to press TIMER to engage or disengage the timer recording standby mode When this function is set to OFF You have to press TIMER to engage or disengage the timer recording standby mode E SUPERIMPOSE ON OFF When this function is set to ON various VCR status information on screen display appears on the screen NOTE When you use this VCR as the playback VCR for editing a tape be sure to set this function to OFF otherwise the VCR status information on screen display will be recorded on the edited tape E AUTO SP EP TIMER ON OFF When this function is set to ON the VCR automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer recording in SP mode For Example Recording a program of 140 minutes in length onto a 120 minute tape Approximately 110 minutes Approximately 30 minutes SP mode EP mode NOTES If you have programed the VCR to timer record 2 or more programs do not use this function but change the tape speed manually during timer programing There may be some noise and sound disturbance where the tape speed switches from SP to EP mode on the tape This function is not available during ITR Instant Timer Recording and wil
4. 6 8 Ibs Format VHS NTSC standard Maximum recording time SP 210 min with ST 210 video cassette EP 630 min with ST 210 video cassette VIDEO AUDIO Signal system NTSC type color signal and EIA monochrome signal 525 lines 60 fields Recording Playback DA 4 Double Azimuth head helical system scan system Signal to noise ratio 45 dB Horizontal resolution 230 lines Frequency range Normal audio 70 Hz to 10 000 Hz Hi Fi audio 20 Hz to 20 000 Hz Input Output RCA connectors IN x 2 OUT x 1 TUNER Tuning system Channel coverage Frequency synthesized tuner VHF Channels 2 13 UHF Channels 14 69 CATV 113 Channels RF output Channel 3 or 4 switchable preset to Channel 3 when shipped 75 ohms unbalanced TIMER Clock reference Quartz Program capacity 1 year programmable timer 8 programs Memory backup for timer is not supported ACCESSORIES Provided accessories RF cable F type Infrared remote control unit AA battery x 2 Specifications shown are for SP mode unless specified otherwise E amp O E Design and specifications subject to change without notice FOR SERVICING Only in U S A HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE 1 800 537 5722 http www jve com Dear Customer In order to receive the most satisfaction from your purchase please read the instruction booklet before operating the unit In the event that repair is necessary or for
5. Each time you press PROG CHECK the next program s Program screen appears E1 Cancel or change program setting To cancel a program press CANCEL when the Program screen you do not want is shown R START STOP CH 8 00P 10 00 12 10 00A 10 45 40 11 30P 1 00 125 PI 1 2 3 4 5 6 7 8 PRESS CHECK TO NEXT Timer Recording To change a program press the appropriate button START STOP DATE CH and or SP EP when the Program screen on which you want to make changes is shown E Return to normal screen Press PROG CHECK repeatedly until no Program screen is shown FA Reengage timer recording standby mode Press TIMER The VCR turns off automatically and is displayed on the display panel When AUTO TIMER is set to ON the timer recording standby mode automatically resumes when you turn off the VCR Program overlap warning display If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears you have another program overlapping the program you have just made The Program Check screen appears and conflicting programs will start blinking PR START STOP CH DATE z 1 8 00P 10 00 12 12 24 PROGRAM NOT COMPLETED 0 00A 10 45 40 12 255 11 30P 1 00 125 12 25 7 9 00P 10 00 10 12 24 3 PROGRAM OVERLAP 4 5 6 7 8 4 7 THEN p gt PROG END Example Program 1 you have just made and Program 4 overlap each other El Select program to modify PR START STOP CH DATE 7 P
6. RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so these limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state JVC COMPANY OF AMERICA 1700 Valley Road DIVISION OF JVC AMERICAS CORP Wayne New Jersey 07470 REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY THIS WARRANTY DOES NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT For customer use Enter below the Model No and Serial No which is located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No Purchase date Name of dealer
7. Setting channels manually Manual Channel Set You can add the channels you want or delete the channels you do not want manually E Access Main Menu screen then Tuner MAIN MENU FUNCTION SET Set screen TONER SET Press MENU on the Remote Press AV to INITIALSET move the highlight bar arrow to TUNER SET then press OK or gt PRESS a v THEN OK PRESS MENU TO END FA Access Manual Channel Set screen TUNER SET Press AV to move the highlight bar arrow to MANUAL CHANNEL SET then press OK or gt BAND AUTO CHANNEL SET MANUAL CHANNEL SET SELECT WITH roe AND 0K PRESS MENU TO END E Add or skip desired channels MANUAL CHANNEL SET To add channels SATY 1 Press the Number keys on the Remote to input a channel number you want to add See a v THEN 0K Press OK or gt to set to ADD PRESS MENU TO END Repeat 1 to 2 to add other channels Press MENU to return to normal screen To skip channels 1 Press AV or the Number keys to select a channel number you want to skip Press OK or gt gt to set to SKIP Repeat 1 and 2 to skip other channels Press MENU to return to normal screen no no p5 Cable Box and or DBS Receiver Control Setting The following procedure is required if you receive your TV channels through a cable box descrambler and or if you receive satellite channels t
8. timer recording standby mode The VCR turns on and rewinds to the index code indicating the beginning of the last timer recorded program then begins playback automatically You can access a program of 2 to 9 index codes away from the current position on the tape If for example you have 5 programs recorded and you want to watch the third one press REVIEW three times The Instant Review function will also operate if the VCR is turned on Skipping unwanted portions Skip Search Press SKIP SEARCH on the Remote once to 4 times during playback Each press initiates a 30 second period of high speed playback up to 2 minutes When the specified portion of the tape is skipped normal playback resumes automatically To return to normal playback during Skip Search press PLAY B gt x Recording It may be unlawful to record or play back copyrighted material without the consent of the copyright owner Accidental erasure prevention To prevent accidental recording on a ED recorded cassette remove its record LAA safety tab To record on it later cover GEE Record safety tab the hole with adhesive tape Basic Recording El Load a cassette Make sure the record safety tab is intact If not cover the hole with adhesive tape before inserting the cassette The VCR turns on and the counter is reset automatically FA Select recording channel Press CH or the Number keys on the Remote CH on the VCR Or pus
9. Fl R NORM MIX This VCR can record two sound tracks simultaneously normal and Hi Fi on a Hi Fi stereo tape You can select the sound track s to listen to while playing back a Hi Fi stereo tape In addition when playing back a prerecorded tape containing two separate audio programs on the Hi Fi tracks you can choose either one by selecting either HI FI L or HI FI R HI FI Normally select this Hi Fi sound is played back HI FI L Sound on the left Hi Fi channel is played back HI FI R Sound on the right Hi Fi channel is played back NORM Sound on the normal track is played back MIX Both sounds on the Hi Fi track and normal track are mixed and played back NOTES While playing back a monaural tape sounds on the normal track will be heard regardless of this setting If RF connection is used for viewing pictures on the TV sound will be monaural even though you select HI FI e You can also use the A MONITOR button on the Remote to select the desired monitor sound E AV COMPU LINK ON OFF The remote PAUSE AV COMPULINK terminal on the rear panel can be used as either the remote PAUSE terminal or the AV COMPULINK terminal When this function is set to ON you can use this terminal as the AV COMPULINK terminal By connecting other JVC s AV COMPULINK components including amplifiers or receivers and televisions one touch control of the audio and video components linked via their AV
10. IS NOT COVERED This limited warranty provided by JVC does not cover 1 Products which have been subject to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service or if affixed to any attachment not provided with the products or if the model or serial number has been altered tampered with defaced or removed Initial installation and installation and removal for repair Operational adjustments covered in the Owner s Manual normal maintenance video and audio head cleaning Damage that occurs in shipment due to act of God and cosmetic damage Signal reception problems and failures due to line power surge Video Pick up Tubes CCD Image Sensor Cartridge Stylus Needle are covered for 90 days from the date of purchase Accessories Batteries except that Rechargeable Batteries are covered for 90 days from the date of purchase There are no other express warranties except as listed above THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT INCONVENIENCE LOSS OR ANY OTHER DAMAGES WHETHER DIRECT INCIDENTAL OR CONSEQUENTIAL INCLUDING WITHOUT LIMITATION DAMAGE TO TAPES RECORDS OR DISCS
11. Set remote control code for Remote Press and hold A B Press the Number key 2 3 Press OK and release A B The Remote now can transmit B code control signals FA Check remote control code for VCR Press and hold on the VCR for more than 5 seconds while the VCR is turned off The code currently set appears on the display panel Change code for VCR Press any key on the Remote The VCR now responds to B code control signals To set the Remote and the VCR back to A code control signals repeat the same procedure as shown above except pressing the Number key 1 in step 2 of EE m Other Functions To control two VCRs with the same Remote You can control two JVC VCRs by switching the remote control code for the Remote between A and B F step Hl keeping two VCRs to different control codes To change only the remote control code for the Remote DO NOT perform steps H and E e e Editing You can use your VCR as the playback or recording VCR You can use a camcorder as the playback VCR and your VCR as the recording VCR Refer also to the other components instruction manuals for connection and its operations EE Make connections Example When using this VCR as the playback VCR This VCR for playback t t t To AUDIO VIDEO OUT Audio video cable not supplied Z v 1 To audio video input Another VCR for recording W
12. fire electric shock or other hazards 4 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operating condition How to use the Remote Before use insert two AA size batteries into the Remote with the polarity and matched correctly as indicated on the battery compartment or on the lid The Remote can operate most of your VCR s functions as well as basic functions of TV sets cable boxes and DBS receivers Point the Remote toward the remote sensor on the target component The maximum operating distance of the remote control is about 8m NOTE If the Remote does not work properly remove its batteries wait for a few seconds replace the batteries and then try again Video heads cleaning Use a dry cleaning cassette TCL 2UX when Rough poor picture appears while a tape is played back The picture is unclear or no picture appears USE CLEANING CASSETTE appears on the screen only with SUPERIMPOSE set to ON E Buttons Connectors and Indicators Front Panel Cassette loading slot Advanced CH PLAY JOG dial REC LINK POWER RECLINK amp VIDEO AUDIO DISPLAY Remote REC PAUSE input connectors sensor 24HR QUICK STOP EJECT PROGRAM Display panel Timer mode indicator Play indicator VCR mode indicator Reco
13. A 1 17 UNIVERSAL 16 17 25 VIDEOWAY 3 9 22 ZENITH 3 9 22 DBS RECEIVER CODE DBS RECEIVER CODE BRAND BRAND JVC DISH Network 51 PRIMESTAR 50 ECHOSTAR DISH 51 SONY DSS 41 Network RCA DSS 40 For cable box CABLE BOX BRAND SET e If the cable box s channel changes to 9 1 setting is complete Press OK If the cable box s channel does not change to 9 1 Press A entering another code to move the highlight bar arrow to NO then press OK or gt 2 Repeat step W until the cable box s channel changes to 9 by DID YOUR CABLE BOX CHANGE TO CHANNEL 09 NO PRESS a v THEN OK PRESS MENU TO END 3 If the channel does not change after going through all the code numbers listed for your model of cable box then try all the other numbers For DBS receiver DBS RECEIVER BRAND SET e If the DBS receiver s channel changes to 51 the channel listed below for your brand Sin your nes RECEIVER setting is complete Press OK or CHANGE TO CHANNEL 100 JVC 100 SONY 205 No ECHOSTAR 100 PRIMESTAR gt 55 RCA 205 PRESS a v THEN OK PRESS MENU TO END e If the DBS receiver s channel does not change as shown above 1 Press A press OK or Repeat step i m to move the highlight bar arrow to NO then E Playback Basic Playback E Load a cassette Make sure the win
14. A Situate VCR Place the VCR on a stable horizontal surface Connect VCR to TV Antenna or cable 4 Coaxial cable Flat feeder AC power cord Cc Back of VCR AC outlet To audio video input connectors Audio video cable not supplied To 75 Q terminal RF cable supplied RF Connection 1 Disconnect the TV antenna from the TV 2 Connect the TV antenna cable to the ANT IN terminal on the rear of the VCR 3 Connect the supplied RF cable between the TV OUT terminal on the rear of the VCR and the TV s antenna input terminal AV Connection improves picture quality during tape playback If your TV is equipped with audio video input connectors 1 Connect the antenna VCR and TV as shown in the illustration 2 Connect an audio video cable between the AUDIO VIDEO OUT connectors on the rear of the VCR and the audio video input connectors on the TV e Even if you are using audio video cables to connect your VCR to your TV you must also connect it using the RF cable This will ensure that you can record one show while watching another E1 Perform Plug amp Play setup Plug the AC power cord into an AC outlet Do not turn on the VCR The clock and tuner channels will be set automatically The time and date can be set automatically by the clock setting data transmitted from one of the regular TV broadcast ch
15. BA Turn the JOG dial to the left or right to set pall time the start time pr onn One click stop of the JOG dial changes 8 S LLI the time in 5 minute intervals El Push the JOG dial O starts blinking on the display panel Turn the JOG dial to the N left or right to set the stop time Za aS EJ Push the JOG dial Turn the JOG dial to Channel number the left or right to select the channel then press 24HR QUICK PROGRAM The VCR turns off automatically and is displayed on the display panel NOTES If Err appears on the display panel repeat the above steps again When a menu screen is shown you cannot use 24HR Quick Programing function Press MENU to return to normal screen and try again You can use 24HR Quick Programing function also when the VCR is turned off For 24HR Quick Programing function the program overlap warning display does not appear even if some programs overlap each other _ v Stop time ann Se TU m To use the VCR while it is in timer recording standby mode Press TIMER then press POWER After you use the VCR press TIMER again to put the VCR into timer recording standby mode Checking canceling or changing program settings El Disengage timer Press TIMER then press POWER When AUTO TIMER is set to ON you do not have to press TIMER BA Access Program Check screen Press PROG CHECK Access Program screen Press PROG CHECK again
16. COMPULINK connectors becomes possible When this function is set to OFF you can use this terminal as the remote PAUSE terminal If your JVC camcorder is equipped with the Master Edit Control you can control the VCR from the camcorder Connect the mini plug cable not supplied with this VCR between the remote PAUSE terminal and the EDIT connector on the camcorder NOTE Refer to the other components instruction manuals for connection and its operations Satellite Auto Recording You can automatically record a satellite program which is timer programed on your DBS receiver El Connect a DBS receiver to the AUDIO VIDEO IN connectors on the rear panel You can also connect the cable box if it has a timer B Set timer program on DBS receiver referring to its instruction manual El Load a cassette with the record safety tab intact El Press SP EP to set the tape speed H Press REC LINK The VCR turns off automatically and enter the Satellite Auto Recording standby mode the REC LINK lamp lights When signals come into the VCR from the DBS receiver the VCR starts recording the REC LINK lamp blinks and stops recording and goes off when signals stop coming in NOTES Be sure not to turn on the DBS receiver before the program starts broadcasting otherwise the VCR will start recording when the DBS receiver is turned on To disengage the Satellite Auto Recording standby mode press REC LINK the REC LINK lamp
17. JVC LPT0502 001B COPYRIGHT 2000 VICTOR COMPANY OF JAPAN LTD Dear Customer Thank you for purchasing the JVC VHS video cassette recorder Before use please read the safety information and precautions to ensure safe use of your new VCR CAUTIONS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CAUTION This video cassette recorder should be used with AC 120V U 60Hz only To prevent electric shocks and fire hazards DO NOT use any other power source CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND Note to CATV system install
18. N connectors on the rear of the VCR and the audio video output connectors on the unit if both a cable box and a DBS receiver are used it is recommended that you connect the DBS receiver to your VCR s AUDIO VIDEO IN connectors and the cable box to your VCR s ANT IN connector Z4 Connect Controller to VCR Connect the Controller to the CABLE BOX Controller connector on the rear panel E Turn on cable box or DBS receiver Select a channel other than channel 9 on your cable box or channels 55 100 205 on your DBS receiver EJ Access Main Menu screen then Initial Set screen on VCR Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt Access Cable Box Set screen or DBS INITIAL SET Receiver Set screen CLOCK SET LANGUAGE ENGLISH Press AV to move the highlight bar GUIDE CHANNEL SET arrow to CABLE BOX SET or DBS CABLE BOX SET DBS RECEIVER SET RECEIVER SET then press OK or gt SELECT WITH a AND OK PRESS MENU TO END EJ Select output channel CABLE BOX SET Your selection depends on how the unit is connected to your VCR e If the unit is connected to your VCR s ANT IN terminal on the rear panel Press AV until the channel number representing the cable box s output CH2 CH9 or DBS receiver s output CH3 or CH4 appears on the screen e If the unit is connected to your VCR s AUDIO VIDEO IN connectors on the front panel press A
19. RKMANSHIP from the date of original retail purchase for the period as shown below The Warranty Period PARTS LABOR lyr 90pays THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY 50 UNITED STATES THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO WHAT WE WILL DO If this product is found to be defective JVC will repair or replace defective parts at no charge to the original owner Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers Parts used for replacement are warranted only for the remainder of the Warranty Period All products and parts thereof may be brought to a JVC authorized service center on a carry in basis except for Television sets having a screen size 25 inches and above which are covered on an in home basis WHAT YOU MUST DO FOR WARRANTY SERVICE Return your product to a JVC authorized service center with a copy of your bill of sale For your nearest JVC authorized service center please call toll free 800 537 5722 If service is not available locally box the product carefully preferably in the original carton and ship insured with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center the name and location of which will be given to you by the toll free number If you have any questions concerning your JVC Product please contact our Customer Relations Department WHAT
20. V until ON F 1 FRONT appears on the screen e If the unit is connected to your VCR s AUDIO VIDEO IN connectors on the rear panel press AV until ON L 1 REAR appears on the screen If you do not use any unit press AV until OFF appears on the screen El Access Brand Set screen Press OK or gt e If the Clock Set screen appears perform Manual Clock Set If you press MENU after the clock has been set the Brand Set screen appears S kd PRESS A Y THEN OK PRESS MENU TO END Initial Settings E Enter brand code and perform test Press the appropriate Number keys on the Remote to enter the brand code from the following list then press OK or gt CABLE BOX BRAND SET 5 KA gt PRESS NUMBER KEY 0 9 THEN OK TO TEST PRESS MENU TO END CABLE BOX BRAND CODE ARCHER 1 5 17 CABLETENNA 1 17 CABLEVIEW 15 16 17 21 25 CITIZEN 15 16 17 21 25 CURTIS 2 8 DIAMOND 1 17 EASTERN 19 GC BRAND 15 16 17 21 25 GEMINI 15 GENERAL INSTRUMENTS 1 4 6 11 12 15 28 HAMLIN 10 18 19 23 JASCO 15 JERROLD 1 4 6 11 12 15 28 NOVAVISION 2 8 OAK 7 20 PANASONIC 13 14 PULSER 15 16 17 21 25 RCA 13 14 REGAL 10 18 19 23 REGENCY 19 REMBRANDT 1 16 17 SAMSUNG 5 16 24 SCIENTIFIC ATLANTA 2 8 SIGMA 7 20 SL MARX 5 16 17 24 25 SPRUCER 13 14 STARGATE 5 15 16 17 21 24 25 TELEVIEW 5 16 24 TOCOM 1 4 16 UNIK
21. Y 0 8 number is received on the VCR or PRESS BRAG ED END cable box then press OK To set the tape speed press SP EP To change the stop time press STOP To timer record daily Monday Friday or weekly serials press DAILY M F or WEEKLY Pressing the button again makes the DAILY or WEEKLY display disappear If you made a mistake press CANCEL to access the PlusCode No screen again If an incorrect PlusCode number or the one for a broadcast already finished has been inputted ERROR is displayed for about 5 seconds then the PlusCode No screen reappears El Press OK or PROG if PROGRAM NOT COMPLETED PROGRAM OVERLAP appears see Program overlap warning display El Press TIMER The VCR turns off automatically and is displayed on the display panel GUIDE CHANNEL SET Express Timer Programing Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically El Press PROG on the Remote to access the PlusCode No screen BA Press START once to access PROGRAM 1 Program screen START STOP Press START STOP DATE or CH repeatedly to enter the start time stop time date or channel PRESS SP EP 8 DAILY Press and hold START or STOP Renee rhe Ne to increase the time in 30 minute intervals To set the tape speed press SP EP To timer record daily Monday Friday or weekly seri
22. als press DAILY M F or WEEKLY Pressing the button again makes the DAILY or WEEKLY display disappear If you are using a DBS receiver and PROGRAM 1 DBS RECEIVER SET is set to ON START the band indication appears under 5 ATE the channel number indication wit Sa Refer to Cable Box and or DBS Receiver Control Setting PRESS a SP EP alia 9 WEEKLY 7 DBS THEN OK PRESS PROG TO END TV To timer record a regular TV broadcast received on the VCR CATV To timer record a cable TV broadcast received on the VCR or through a cable box unless CABLE BOX SET is set to OFF DBS To timer record a satellite broadcast received through a DBS receiver If the channel number entered requires that the band be set and 7 DBS is displayed on the screen press DBS to select DBS El Press OK or PROG If PROGRAM NOT COMPLETED PROGRAM OVERLAP appears see Program overlap warning display El Press TIMER The VCR turns off automatically and is displayed on the display panel 24HR Quick Programing You can program a timer recording that starts within 24 hours using the JOG dial on the VCR Load a cassette with the record safety tab intact The VCR turns on and the counter is reset automatically El Press 24HR QUICK PROGRAM on the VCR T gt starts blinki he displ 2 TUL CR starts blinking on the display J EC ETI o panel
23. annels We call this TV channel the host channel and it is a PBS channel in your area ATTENTION If you use a cable box Plug amp Play will not function set the clock and tuner channels separately Ce During Initial Auto Clock Set Aut blinks ind uc v During Auto Channel Set uf The channel numbers are displayed as they are scanned and set Plug amp Play Completed H HH The current time is displayed What to do if Plug amp Play setting failed If an incorrect time is displayed on the display panel perform the Semiauto Clock Set or Manual Clock Set procedure If appears on the display panel ensure that the antenna cable is connected correctly Then turn on and off the VCR the Plug amp Play setting will be automatically reactivated If Plug amp Play setting is not performed though the antenna cable is connected correctly perform Manual Clock Set and Auto Channel Set or Manual Channel Set E Set VCR channel The VCR channel is the channel on which you can watch the picture from the VCR on the TV when only using the RF connection Press POWER to turn off the VCR then press STOP EJECT W amp on the VCR for more than 5 seconds CH3 appears on the display panel Press CH on the Remote to select CH3 CH4 or CH OFF then press OK The VCR channel is preset to CH3 Set to CH4 if CH3 is used for broadcast
24. ator appears The position of in relation to B Beginning or E End shows you where you are on the tape Set SUPERIMPOSE to ON Changing display information Each time you press DISPLAY the display panel shows the channel number and the clock time alternatively You can change display in the stop recording or of T recording pause mode or during rewind fast forward high speed search When SUPERIMPOSF is set to ON and DISPLAY on the Remote is pressed time counter will appear on the TV screen To reset the time counter press C RESET on the Remote Function settings You can use the other useful function settings on the Function Set screen E Access Main Menu screen then MAIN MENU Function Set screen Press MENU on the Remote Press AV to INITIAL SET move the highlight bar arrow to FUNCTION SET then press OK or bA PRESS a v i THEN OK PRESS MENU TO END FA Select Function Press AV to move the highlight bar arrow to the function you want to set FUNCTION PREVIOUS PAGE VIDEO CALIBRATION ON PICTURE CONTROL AUTO Te AUTO TIMER OFF AUDIO MONITOR HI FI SUPERIMPOSE ON AV COMPU LINK ON AUTO SP EP TIMER OFF VIDEO STABILIZER OFF NEXT PAGE SELECT WITH 4 AND OK PRESS MENU TO END SELECT WITH 47 AND OK PRESS MENU TO END Change setting Press OK or gt The default setting is bold in the table below Press MENU to return t
25. bar arrow to CLOCK SET then press OK or LANGUAGE iiei cee CABLE BOX SET DBS RECEIVER SET SELECT WITH a AND OK PRESS MENU TO END Setting clock semiautomatically Semiauto Clock Set You can change the host channel D S T Daylight Saving Time time zone setting manually First follow steps fl to A in Preparations above then go to the following steps NOTE The time set previously will be erased when AUTO CLOCK HOST CH D S T or TIME ZONE setting is changed El Set Auto Clock to ON CLOCK SET Press OK or on the Remote repeatedly MIME ae DATE EA to move the highlight bar to AUTO AUTO CLOCK ON M CLOCK then press AV so that ON is selected HOSTCH ZAUT CATV D S T AUTO TIME ZONE AUTO PRESS a v THEN OK PRESS MENU TO END FA Select host channel You can either select AUTO or enter a PBS channel number Press OK or gt to move the highlight bar to HOST CH then press AV repeatedly until AUTO or the desired PBS channel number is selected Select D S T mode Press OK or gt to move the highlight bar to D S T then press AV repeatedly until the desired setting is selected AUTO Select if you want to adjust your VCR s clock automatically by the incoming signal from the host channel Auto Daylight Saving Time enables automatic adjustment of the VCR s clock at the start and end of Daylight Saving Time Be sure t
26. dow side is up the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR Do not apply too much pressure when inserting The VCR turns on and the counter on the on screen display is reset automatically If the cassette s record safety tab has been removed playback begins automatically EA Start playback Press PLAY B gt During playback Stop playback Press STOP W on the Remote OR Press STOP EJECT M 4 on the VCR Pause playback and view still picture Press PAUSE If OR Push the JOG dial Press PLAY P to resume Push the JOG dial again to normal playback resume normal playback Pause and Frame by Frame playback Press PAUSE II to pause OR Push the JOG dial to pause then press kaa or BPI or then turn the JOG dial to the PAUSE Ill repeatedly left or right Press PLAY P to resume Push the JOG dial again to normal playback resume normal playback Rewind fast forward Press REW lt lt 4 or FF OR Turn the JOG dial quickly to PP the left or right Press PLAY B gt to resume normal playback If you press and hold REW lt 4 or FF gt for more than 2 seconds simply releasing it cancels the picture search and normal playback resumes Rewind fast forward at variable speed including slow motion Press ka a or gt gt OR Turn the JOG dial to the left repeatedly or right Press PLAY P to resu
27. er This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical VIDEO CASSETTE RECORDER HR VP793U INSTRUCTIONS Printed in Malaysia 1100 IYV gt KID KPJ CAUTION Changes or modifications not approved by JVC could void user s authority to operate the equipment Declaration of Conformity Model Number HR VP793U Trade Name JVC Responsible Party JVC Americas Corp Address 1700 Valley Road Wayne N J 07470 Telephone Number 973 315 5000 This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Failure to heed the following precautions may result in damage to the VCR Remote or video cassette 1 DO NOT place the VCR in an environment prone to extreme temperatures or humidity in direct sunlight in a dusty environment in an environment where strong magnetic fields are generated on a surface that is unstable or subject to vibration 2 DO NOT block the VCR s ventilation openings 3 DO NOT place hea
28. ey all warnings and instructions marked on your product and its operating instructions For your safety please read all the safety and operating instructions before you operate this product and keep this booklet for future reference INSTALLATION 1 Grounding or Polarization A Your product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug B Your product may be equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 2 Power Sources Operate your product only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company If your product is intended to operate from battery power or other sources refer to the operating instructions 3 Overloading Do not overload wall
29. gain to this VCR after the power failure this VCR starts the Plug amp Play setting automatically to restore the clock time and channel setting If the clock time and channel setting are restored correctly each timer program you have made will start at its start time unless its end time has elapsed Changing VCR Plus Setting The VCR Plus programing system assigns a VCR Plus guide channel to the TV channels and the cable channels These guide channel numbers are also called the VCR Plus channel codes Most TV listings have a section usually a chart indicating the guide channel numbers assigned to each station To ensure that VCR Plus timer recording operates correctly it is necessary to set the VCR Plus Guide Channel Set for each station If you have moved to a different area or if a broadcasting station s channel number has been changed perform the following steps to set the correct guide channel number E Access Main Menu screen then Initial Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt FA Access Guide Channel Set screen Press AV to move the highlight bar arrow to GUIDE CHANNEL SET then press OK or Input guide channel number Press AV or the Number keys to select the VCR Plus guide channel number as shown in the TV listing then press OK or GUIDE CHANNEL SET VCRCH gt PRESS NUMBER KEY 0 9 4
30. goes off Depending on the type of satellite receiver Satellite Auto Recording may not be compatible Other Functions Child Lock You can disable the VCR operations While the VCR is turned on press and hold POWER on the Remote for more than 10 seconds The VCR turns off CL appears for about 5 seconds on the display panel To release the child lock press and hold POWER on the Remote until the VCR turns on NOTES Pressing TIMER during timer recording unplugging the AC power cord or a power outage also releases the child lock When the child lock function is in use keep the Remote out of the children s reach Timer recording programs will be performed even if the child lock function activated Multi Brand Remote Control This Remote can control some functions of remote controllable TVs cable boxes or DBS Direct Broadcast Satellite receivers listed below Without setting you can control a JVC TV NOTES Some unit s brands have more than one code If the unit does not function with a specified code try other codes Depending on the type of unit some or all functions cannot be operated using this Remote Its not possible to operate a unit not equipped with a remote sensor Its not possible to set the Remote for both your cable box and a DBS receiver at the same time Once you have set the Remote to operate the unit you do not have to set it until you replace the batteries fro
31. h the JOG dial then turn it to the left or right If you connect the TV and the VCR only using the RF connection press TV VCR on the Remote so that the VCR mode indicator lights on the display panel to view the program to be recorded Set tape speed Press SP EP El Start recording On the VCR press REC Or on the Remote while holding REC press PLAY gt NOTE If VIDEO CALIBRATION is set to ON default setting the VCR takes about 7 seconds to assess the quality of the tape in use then recording begins with the picture level optimized During recording Pause recording Press PAUSE II Press PLAY B gt to resume recording e You can select channel in the recording pause mode Stop recording Press STOP Ml on the OR Press STOP EJECT W 4 on Remote the VCR Recording Features Specifying recording length Instant Timer Recording ITR During recording press REC on the VCR repeatedly until the recording length you want appears on the display panel The record indicator O on the display panel starts blinking Each time you press the button recording length increases in 30 minute intervals up to 6 hours The VCR shuts off after recording is finished To cancel an ITR press STOP MM on the Remote or STOP EJECT H amp on the VCR Watching one program while recording another During recording If you connect the TV and the VCR only using the RF c
32. hen using this VCR as the recording VCR connect this VCR s audio video input connectors to the audio video output connectors on the other VCR If the playback VCR is monaural connect the audio output connector on the playback VCR to the left audio input connector on this VCR FA Load cassettes Insert the playback cassette into the playback VCR and the cassette to be recorded on into the recording VCR Select input mode on recording VCR Select the correct external input on the recording VCR On this VCR when using this VCR as the recording VCR Select L 1 when connecting the other VCR to the audio video input connectors on the rear panel Select F 1 when connecting the other VCR to the audio video input connectors on the front panel Press AUX or CH on the Remote CH on the VCR EJ Select edit mode Set the edit mode to ON for the VCRs if such a mode is equipped On this VCR set PICTURE CONTROL to EDIT E Start playback Press PLAY on the playback VCR EJ Start recording Press REC on the recording VCR Specifications GENERAL Power requirement Power consumption AC 120 Vw 60 Hz Power on 18W Power off 20W Temperature Operating 5 C to 40 C 41 F to 104 F Storage 20 C to 60 C 4 F to140 F Operating position Horizontal only Dimensions W x H x D 400 mm x 94 mm x 255 mm 15 3 4 x 3 3 4 x 10 1 16 Weight 3 1 kg
33. hrough DBS Direct Broadcast Satellite receiver The Controller allows the VCR to automatically switch the cable box or DBS receiver s channel during timer recording NOTES The Controller is not supplied with this unit It can be requested by mailing in the completed JVC Cable Mouse Certificate that is included with the accessory package For the cable box the Controller is effective for VCR Plus or Express timer programing For the DBS receiver the Controller is effective only for Express timer programing When connecting your cable box or DBS receiver refer to its instruction manual E Situate Controller If both a cable box and a DBS receiver are used position the Controller so its signal reaches the remote sensors on both the cable box and DBS receiver FA Attach Controller Fix securely using the adhesive strip attached on the back of the Controller Cable box or DBS receiver Controller Your VCR suggested locations EJ Connect cable box and or DBS receiver to VCR Cable box or DBS receiver Transmitter RF out Audio video output Controller To ANT IN To AUDIO VIDEO IN VCR If your cable box or DBS receiver does not have audio video output connectors connect the RF output terminal on the unit to the ANT IN terminal on the rear of your VCR If your cable box or DBS receiver has audio video output connectors connect an audio video cable between the AUDIO VIDEO I
34. ing in your area EJ Final preparation for use Turn on the VCR and the TV and select the VCR channel 3 or 4 or AV mode on the TV You can now perform basic playback or basic recording E Initial Settings Language Setting The default setting is ENGLISH El Access Main Menu screen then MAIN MENU FUNCTION SET TUNER SET Initial Set screen Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt PRESS a Y THEN OK PRESS MENU TO END A Select language INITIAL SET This VCR offers you the language choice to CLOCK SET view menus and some messages in E English Spanish or French Press AV to move the highlight bar arrow to LANGUAGE then press OK or gt repeatedly until the desired language is selected Press MENU to return to normal screen LANGUAGE ENGLISH CABLE CHANNEL SET DBS RECEIVER SET SELECT WITH a v AND OK PRESS MENU TO END Initial Settings Clock Setting Perform clock setting only if the clock has not been set correctly by the Plug amp Play setting or if you use a cable box Preparations E Access Main Menu screen then MAIN MENU Initial Set screen FUNCTION SET Press MENU on the Remote Press AV to move the highlight bar arrow to INITIAL SET then press OK or gt PRESS 4 THEN OK PRESS MENU TO END EA Access Clock Set screen INITIAL SET Press AV to move the highlight
35. ing to qualified service personnel 2 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT NEC SECTION 810 20 ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE PORTABLE CART WARNING Symbol provided by RETAC d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way f When the product exhibits a distinct change in performance this indicates a need for service 3 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or which have the same characteristics as the original part Unauthorized substitutions may result in
36. l not work properly on the following tapes T ST 30 T ST 60 T ST 90 and T ST 120 E VIDEO STABILIZER ON OFF When this function is set to ON you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR NOTE To watch recordings with close caption or when you finish viewing a tape set this function to OFF E BLUE BACK ON OFF When this function is set to ON the TV screen becomes all blue in the following cases When receiving a channel not in use When stopping playback NOTE When you want to receive an unstable channel with poor signals set this function to OFF W 2ND AUDIO RECORD ON OFF When this function is set to ON If a SAP program is received the SAP audio is recorded on both the normal and Hi Fi tracks The main audio is not recorded If a non SAP program is received the main audio is recorded on both the Hi Fi and normal tracks When this function is set to OFF the SAP audio cannot be recorded NOTES When the channel is changed on the VCR The STEREO indication appears on the screen for about 5 seconds if the program is a stereo broadcast The SAP indication appears on the screen for about 5 seconds if the program is a SAP broadcast Both indications appear when a stereo program is accompanied by SAP sound AUDIO MONITOR HI FI HI FI L HI
37. m the Remote TV Brand Setting EB Turn on TV Turn on the TV using the Power button on the TV or its Remote PA Set TV brand code Press and hold TV 2 Press MBR SET 3 Press the Number keys to enter your TV s brand code 4 Press OK and release TV The TV should turn off EJ Operate TV While holding down TV press one of the following buttons POWER TV VCR TV CH 4I TV Muting TV VOL and the Number keys For some brands you must press ENTER after having pressed the Number keys to enter a channel number TV BRAND CODE TV BRAND CODE JVC 01 03 SONY 07 HITACHI 10 SAMSUNG 12 MAGNAVOX 02 SANYO 13 MITSUBISHI 03 SEARS 13 PANASONIC 04 11 TOSHIBA 08 RCA 05 ZENITH 09 SHARP 06 Cable Box or DBS Receiver Brand Setting E Turn on cable box or DBS receiver Turn on the cable box or DBS receiver using the Power button on the unit or its Remote FA Enter brand code 1 Press and hold CABLE DBS 2 Press MBR SET 3 Press the Number keys to enter your cable box s or DBS receiver s brand code 4 Press OK and release CABLE DBS Operate cable box or DBS receiver While holding down CABLE DBS press one of the following buttons POWER TV CH and the Number keys For some brands you must press ENTER after having pressed the Number keys to enter a channel number To change the cable box s or DBS receiver s channel
38. me normal playback Each time you press lt 4 or PI or each time JOG dial passes a click position the playback speed changes To decrease the speed during picture search press the opposite direction button repeatedly or turn the dial in the opposite direction During still picture press and hold BP to start forward or lt lt 4 to start reverse slow motion playback When you release the button still picture resumes During still picture holding PAUSE II for more than 2 seconds also starts forward slow motion playback If you press PAUSE Il again still picture resumes Reverse Forward Reverse Reverse Reverse Slow Normal Forward search play motion play search 3 steps monon 2 steps 4 steps 2 steps Playback When the tape is not running Rewind fast forward at high speed Press REW lt lt or FF OR Turn the JOG dial to the left PP or right Eject the tape Press STOP EJECT H amp You can also eject the cassette when the VCR is turned off Turn off the VCR Press POWER Playback Features Adjusting tracking condition Tracking Adjustment Automatic tracking adjustment Whenever you insert a tape and start playback automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback Manual tracking adjustment If automatic tracking cannot eliminate noises well during playback follow the procedures below
39. n 2 seconds For Automatic Power Off Press REW lt lt then press POWER within 2 seconds For Automatic Timer Standby Press REW lt lt then press TIMER within 2 seconds NOTE It is not possible to select the Automatic Timer Standby function if the cassette s record safety tab is removed Playing back tape repeatedly 100 times Repeat Play During playback press and hold PLAY for more than 5 seconds The play indicator on the display panel starts blinking slowly To stop playback press STOP lM on the Remote or STOP EJECT W amp on the VCR Locating beginning of recordings Index Search Index codes are placed on the tape at the beginning of each recording when recording on this VCR E While the tape is not running press SHUTTLE PLUS ka a or PP on the Remote to start search H To access a recording of 2 to 9 index codes away press lt 4 or P repeatedly until the correct number is displayed on the screen only if SUPERIMPOSE is set to ON Playback begins automatically when the desired recording is located Beginning of the _ Current Beginning of the current program position on 2nd next program recorded the tape recorded Previous Next program program 2nd next recorded recorded 2 1 1 2 lt 3 a gt gt r gt Locating beginning of timer recordings Instant Review Press REVIEW on the Remote after ensuring that the VCR is in the
40. nt will be made by the built in clock itself OFF Select when Daylight Saving Time does not apply to you Start clock Press MENU and normal screen appears DATE 1 00AM 12 24 AUTO CLOCK OFF gt a a gt PRESS a v THEN OK PRESS MENU TO END To make corrections any time during the process Press OK or gt repeatedly until the item you want to change blinks then press AV Tuner Setting Setting channels automatically Auto Channel Set Perform Auto Channel Set only if channels have not been set correctly by the Plug amp Play setting El Access Main Menu screen then Tuner MAIN MENU FUNCTION SET Set screen TUNER SET Press MENU on the Remote Press AV to NIMALSET move the highlight bar arrow to TUNER SET then press OK or gt PRESS a Y THEN OK PRESS MENU TO END FA Perform Auto Channel Set TUNER SET Press AV to move the highlight bar BAND aaa CATV arrow to AUTO CHANNEL SET then ETEL CHANNEL SET press OK or D The VCR selects the correct band TV or CATV automatically during Auto Channel Set When Auto Channel Set is complete SCAN COMPLETED appears on screen If the scan was unsuccessful SCAN SCANNING COMPLETED NO SIGNAL appears on screen Check the connections and start again Press MENU to return to normal screen SELECT WITH a AND OK PRESS MENU TO END AUTO CHANNEL SET PRESS MENU TO END Initial Settings
41. o normal screen E VIDEO CALIBRATION ON OFF When this function is set to ON this VCR checks the condition of the tape in use during playback and recording and compensates to provide the highest possible pictures This takes place whenever you play back a tape or start recording after inserting a tape NOTE The VCR checks the tape condition for about 7 seconds then starts recording To make sure you record the desired scene or program completely perform the following steps Press and hold PAUSE II and press REC After about 7 seconds the VCR re enters Record Pause mode Press PLAY B gt to start recording PICTURE CONTROL AUTO NORM EDIT SOFT SHARP This function helps you to adjust the playback picture quality according to your preference AUTO NORM Normally select this Picture quality is adjusted automatically When VIDEO CALIBRATION is OFF NORM will appear instead of AUTO EDIT Minimizes picture degradation during editing recording and playback SOFT Reduces image coarseness when viewing overplayed tapes containing much noise SHARP Clearer sharper edged picture when viewing images with much flat same colored surfaces such as cartoons NOTE Select EDIT when you are editing tapes After you finish editing the tapes select AUTO m Other Functions mm AUTO TIMER ON OFF When this function is set to ON
42. o select the correct time zone manually in step B ON Adjustment will be made by the built in clock itself OFF Select when Daylight Saving Time does not apply to you El Select time zone Press OK or gt to move the highlight bar to TIME ZONE then press AV repeatedly until AUTO or the desired time zone is selected Each time you press the button the time zone changes as follows lt gt AUTO lt gt ATLANTIC lt gt EASTERN lt gt CENTRAL lt gt MOUNTAIN lt gt PACIFIC lt ALASKA lt gt HAWAII 4 gt back to the beginning E Complete Semiauto Clock Set Press MENU to return to normal screen Turn off the VCR Aut will appear on the display panel while the clock is being set The current clock time will appear automatically when the clock setting is complete Setting clock manually Manwal Clock Set First follow steps fll to H in Preparations above then go to the following steps EI Set time date and year CLOCK SET Press AV until the desired time appears SIME DATE YEAR then press OK or gt Set the date and year AUTO CLOCK ON o ony in the same way Der iao CO mai TIME ZONE AUTO Holding AV changes the time in 30 T minute intervals or changes the date in PRESS MENU TO END 15 day intervals FA Select D S T mode CLOCK SET Press OK or gt to move the highlight bar to TIME D S T then press AV to select the desired setting ON Adjustme
43. onnection to view pictures from the VCR press TV VCR on the Remote so that VCR mode indicator goes off from the display panel The TV broadcast being recorded disappears If you are using the AV connection to view pictures from the VCR change the TV s input mode from AV to TV Then select the channel you want to watch on the TV Second Audio Recording This VCR s built in MTS decoder enables reception of Multichannel TV Sound broadcast To record a SAP program received set 2ND AUDIO RECORD to ON a Timer Recording Up to 8 timer recording programs can be made using VCR Plus timer programing Express timer programing or 24HR Quick Programming method as far as a year in advance Remember the clock must be set before you can program the timer NOTES Ifall the 8 programs have already been set PROGRAM FULL or Full appears on the TV screen or the display panel After timer recording is completed the VCR turns off automatically You can program the timer recording while a regular recording is in progress the menu screens will not be recorded To timer record cable or satellite channels perform Cable Box and or DBS Receiver Control Setting and be sure to keep the cable box or DBS receiver turned on Even if a power failure occurs the VCR keeps your timer programs However the clock time channel settings and other menu settings are lost As a result when the power is supplied a
44. outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 4 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product 5 Ventilation Slots and openings in the cabinet are provided for ventilation To ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered Do not block the openings by placing the product on a bed sofa rug or other similar surface Do not place the product in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 6 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer ANTENNA INSTALLATION INSTRUCTIONS 1 Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna di
45. pile carpets 2 Product and Cart Combination A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 3 Water and Moisture Do not use this product near water for example near a bath tub wash bowl itchen sink or laundry tub in a wet basement or near a swimming pool and he like 4 Object and Liquid Entry ever push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any ind on the product 5 Attachments Do not use attachments not recommended by the manufacturer of his product as they may cause hazards 6 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 7 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat SERVICING 1 Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servic
46. rd indicator Channel and auxiliary input Clock time Rear Panel AC power cord CABLE BOX PAUSE AV COMPULINK ANT IN AUDIO VIDEO IN AUDIO VIDEO OUT TV OUT Remote CABLE DBS TV VCR REVIEW Number keys 4 DBS CANCEL C RESET Te i meak STOP START WEAN NENU Foes SHUTTLE PLUS l AV TV CH On screen display EXPRESS PROGRAVEING MBR SET A B POWER A MONITOR DISPLAY DAILY M F PAUSE OK ENTER OSD SHUTTLE PLUS lt lt P lt gt TV VOL If you press OSD on the Remote when SUPERIMPOSE is set to ON you can see the current VCR status on the TV screen Press OSD again to exit on screen display The indications are not recorded even if the VCR is in the recording mode Channel and auxiliary input ae Day and lame clock time E THY 12 00 AM STEREO STEREO TIMER RECORDIN TO START SOON program SAP indication SAP B indication Audio NORM monitor HI FI indications Timer warning display ray VCR operation PAUSE WARNING CANCEL INDEX 1 COUNT mode oo SP Tape speed C Cassette mark L gL Tape position T Index number 1 23 45 Time counter a Connections and Plug amp Play Setting E Check contents Make sure the package contains all of the accessories listed in Specifications F
47. ress AV then press gt FAR 1 00 125 12 25 A UN You can only select one of the overlapping programs If you do not mind this overlap press PROG to finish the timer program setting The program starting earlier or program with the lower program number will be recorded 4 9 00P 10 00 10 12 24 3 6 7 8 a v THEN p PROG END PA Cancel or change program setting PROGRAM 4 To cancel a program press CANCEL when ST ado the Program screen you do not want is DATE cH hd 10 SP shown To change a program press the res fania at appropriate button START STOP PRESS PROG TO END DATE CH and or SP EP when the Program screen on which you want to make changes is shown then press OK If the overlap is not yet solved the conflicting programs will be shown on the Program check screen Repeat the above steps again E Other Functions Timer warning display A warning appears on the TV screen to tell you that the timer recording is to start in 5 minutes if you are not in the timer recording standby mode at that time Press TIMER to put the VCR into timer recording standby mode To clear the display press CANCEL on the Remote WARNING TIMER RECORDING TO START SOON Checking tape position When you change the VCR operation mode from the stop mode to fast forward or rewind mode or when you performan B E Index Search or Instant Review the tape position indic
48. s press TV CH or the Number keys The CH button can be used to change the VCR s channels only CABLE BOX BRAND CODE ARCHER 01 05 17 CABLETENNA 01 17 CABLEVIEW 15 16 17 21 25 CITIZEN 15 16 17 21 25 CURTIS 02 DIAMOND 01 17 EASTERN 19 GC BRAND 15 16 17 21 25 GEMINI 15 GENERAL INSTRUMENTS 01 04 06 11 12 15 28 HAMLIN 10 18 19 23 JASCO 15 JERROLD 01 04 06 11 12 15 28 NOVAVISION 02 OAK 07 PANASONIC 13 14 PULSER 15 16 17 21 25 RCA 13 14 REGAL 10 18 19 23 REGENCY 19 REMBRANDT 01 16 17 SAMSUNG 05 16 24 SCIENTIFIC ATLANTA 02 SIGMA 07 SL MARX 05 16 17 24 25 SPRUCER 13 14 STARGATE 05 15 16 17 21 24 25 TELEVIEW 05 16 24 TOCOM 01 04 16 UNIKA 01 17 UNIVERSAL 16 17 25 VIDEOWAY 03 09 22 ZENITH 03 09 22 DBS RECEIVER BRAND CODE JVC DISH Network 51 ECHOSTAR DISH Network 51 PRIMESTAR 50 SONY DSS 41 RCA DSS 40 Changing Remote Control Code This Remote is capable of transmitting two control codes one set to respond to A code control signals and another set to respond to B code control signals This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals You can easily modify your VCR and the Remote to respond to B code signals When using two JVC VCRs set two VCRs and their Remotes to different codes so that you can operate these VCRs separately EI
49. scharge unit size of grounding connectors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode 2 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANSI NFPA 70 3 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal USE 1 Accessories To avoid personal injury Do not place this product on an unstable cart stand tripod bracket or table It may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Use a mounting accessory recommended by the manufacturer and follow the manufacturer s instructions for any mounting of the product Do not try to roll a cart with small casters across thresholds or deep
50. the address nearest your location within the Continental United States please call 1 800 537 5722 for your nearest authorized servicer or visit our website at www JVC com Remember to retain your Bill of Sale for Warranty Service JVC JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP Sophisticated electronic products may require occasional service Just as quality is a keyword in the engineering and production of the wide array of JVC products service is the key to maintaining the high level performance for which JVC is world famous The JVC service and engineering organization stands behind our products NATIONAL HEADQUARTERS JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP 10 New Maple Avenue Pine Brook NJ 07058 9641 ACCESSORIES Don t service the product yourself To purchase accessories for your JVC product you may contact your local JVC Dealer From the 48 Continental United States call toll free 1 800 882 2345 or on the web at www JVC com CAUTION To prevent electrical shock do not open the cabinet There are no user serviceable parts inside Please refer to qualified service personnel for repairs WARRANTY Only in U S A LIMITED WARRANTY CONSUMER VIDEO 1 90 JVC COMPANY OF AMERICA warrants this product and all parts thereof except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WO
51. vy objects on the VCR or on the Remote 4 DO NOT place anything which might spill on the top of the VCR or on the Remote 5 AVOID violent shocks to the VCR during transport VCR Plus C and PlusCode are registered trademarks of Gemstar Development Corporation The VCR Plus system is manufactured under license from Gemstar Development Corporation For Customer Use Enter below the Model No and Serial No which are located on the rear of cabinet Retain this information for future reference Model No Serial No VHS SQPB He loony Cassettes marked VHS or S VHS can Gf used fixe this video cassette recorder However S VHS recording is not possible with this model This model is equipped with SQPB S VHS QUASI PLAYBACK that makes it possible to play back S VHS recordings with regular VHS resolution HQ VHS is compatible with existing VHS equipment As an ENERGY STAR Partner JVC has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful functions But improper use can result in potential electrical shock or fire hazards This product has been engineered and manufactured to assure your personal safety In order not to defeat the built in safeguards observe the following basic rules for its installation use and servicing ATTENTION Follow and ob

JVC HR-VP693U VCR

Contents

Download Pdf Manuals

Related Search

Related Contents