Enterasys (NPOE1200W) Networking Switch
Contents
1. Connect one end of the DFE POE CBL 2M cable to the 48 Volt OPTIONAL POWER INPUT connector on the N POE switch module Connect one end of the DFE POE CBL 2M cable to the appropriate 48 Volt Output Port connector on the front panel of the N POE Chassis After connecting the cables to both devices press the circuit breaker rocker button to ON Connecting the DFE POE CBL 2M Cable and AC Power Cord Figure 2 5 DFE POE CBL 2M Cable Connections 1 Safety cover and attaching hardware 4 48 Volt OPTIONAL POWER INPUT 2 48 Volt output port connector 5 N POE switch module 3 DFE POE CBL 2M cable Matrix N Series N POE Power System Installation Guide 2 11 Connecting the DFE POE CBL 2M Cable and AC Power Cord 2 12 AC Power Cord Installation AC INLET 1 through AC INLET 4 at the rear of the N POE Chassis provide power to the N POE PSMs in slots PS1 through PS4 respectively An AC power cord is shipped with each N POE PSM To connect the AC power cord refer to Figure 2 6 and proceed as follows In Figure 2 6 the bay cover is showing the bay cover removed for clarity It is not necessary to remove the bay cover to observe the LED indications because they can be seen through the grill in the bay cover 1 Plug the AC power cord into the appropriate AC INLET connector In this example an N POE PSM is installed in N POE Chassis slot PS1 Therefore the AC INLET 1 conn2. comply with this Agreement Upon any such termination You shall immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program 9 OWNERSHIP This is a license agreement and not an agreement for sale You acknowledge and agree that the Program constitutes trade secrets and or copyrighted material of Enterasys and or its suppliers You agree to implement reasonable security measures to protect such trade secrets and copyrighted material All right title and interest in and to the Program shall remain with Enterasys and or its suppliers All rights not specifically granted to You shall be reserved to Enterasys 10 ENFORCEMENT You acknowledge and agree that any breach of Sections 2 4 or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys rights under this Agreement in addition to any and all remedies available at law 11 ASSIGNMENT You may not assign transfer or sublicense this Agreement or any of Your rights or obligations under this Agreement except that You may assign this Agreement to any person or entity which acquires substantially all of Your stock or assets Enterasys may assign this Agreement in its sole discretion This Agreement shall be binding upon and inure to the benefit of the parties their legal representatives permitte
3. ensure that both bay covers are installed during operation Place the N POE Chassis on a flat sturdy surface Refer to Figure 2 1 Unscrew the two captive Phillips head cover screws to release the bay cover from the chassis bay where you plan to install an N POE PSM In this procedure the left bay is used as an example Remove the bay cover and set it aside for now Caution In the following step do not force the power supply into place You could damage the power supply and or the chassis connector Precauci n En el siguiente paso tenga cuidado de no colocar a fuerza la fuente de poder en su sitio Si lo hace podria dafiar tanto la fuente como el conector del chasis Refer to Figure 2 2 Align the N POE PSM with PS1 slot inside bay 1 then slide the N POE PSM forward until the N POE PSM is plugged into the PS1 slot chassis connector and completely inside the bay If significant resistance is encountered before the N POE PSM reaches the end of its travel remove and reinsert the power supply Fasten the N POE PSM to the N POE Chassis using the two captive Phillips head screws on the N POE PSM front panel Repeat steps 2 through 4 for each additional N POE PSM Installing N POE PSMs Caution Remember to replace any bay cover removed during the installation to prevent AN EMI leakage from the chassis Precauci n No olvide volver a colocar todas las tapas de los compartimentos que haya quitado durante el proceso de instalac
4. 5 48 Vdc Output OK PS3 6 5Vdc PS4 7 48 Vdc Output OK PS4 8 5 Vdc Common 9 Standby R Common 10 Standby R Power A2 48 Vdc Power A3 48 Vdc return Matrix N Series N POE Power System Installation Guide A 3 N POE 1200 W Specifications N POE 1200 W Specifications The following section describes the input output port specifications Table A 3 N POE 1200 W Specifications Item Specification Electrical The following are all connected internally to the N POE Chassis AC Input Frequency Range 47 63Hz Input Voltage Range 85 264 Vac Output Voltage 48 Vdc with overload and short circuit protection and over voltage protection OVP to Output Current 67 2 Vde Maximum Output Power 25 0A 1200W Physical Dimensions 4 1 H x 12 7 W x 25 4 D cm 1 6 H x 5 0 W x 10 0 D in Over Temperature Protection OTP Protects against excessive temperatures caused by inadequate blocked airflow fan failure or excessive air inlet temperature Approximate Weight Unit 2 1 kg 4 6 Ib MTBF 247 000 Hours A 4 Specifications AC Power Cord AC Power Cord Any AC power cord used to connect an AC power source to the N POE Chassis must meet the specifications listed in Table A 4 Table A 4 AC Power Cord Specifications Item Specification Cord set The cord set must be approved for use by the governing authority in the country approval of installation Inlet Connector IEC 320 C1
5. CUMULATIVE LIABILITY OF ENTERASYS TO YOU FOR ALL CLAIMS RELATING TO THE PROGRAM IN CONTRACT TORT OR OTHERWISE SHALL NOT EXCEED THE TOTAL AMOUNT OF FEES PAID TO ENTERASYS BY YOU FOR THE RIGHTS GRANTED HEREIN vi 8 AUDIT RIGHTS You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys and accordingly You hereby agree to maintain complete books records and accounts showing i license fees due and paid and ii the use copying and deployment of the Program You also grant to Enterasys and its authorized representatives upon reasonable notice the right to audit and examine during Your normal business hours Your books records accounts and hardware devices upon which the Program may be deployed to verify compliance with this Agreement including the verification of the license fees due and paid Enterasys and the use copying and deployment of the Program Enterasys right of examination shall be exercised reasonably in good faith and in a manner calculated to not unreasonably interfere with Your business In the event such audit discovers non compliance with this Agreement including copies of the Program made used or deployed in breach of this Agreement You shall promptly pay to Enterasys the appropriate license fees Enterasys reserves the right to be exercised in its sole discretion and without prior notice to terminate this license effective immediately for failure to
6. aa xi Howto Uss The Guido nas xii Using the Matrix N Series MEM SSL ads xii Conventens Usad in This GUJE sie xiii Chapter 1 Introduction N POE Power System NPS VEAB corri elisir iii 1 2 I RR AN 1 3 Optional N POE Power Supply Module N POE PSM iiiiiiii iii 1 3 N PUE Poli a5 LESS ul ni e ai aaa 1 4 Powered Devices PDS 1 4 Power Classifications and Deployment ui 1 4 Gallina Help cca iaia 1 7 Chapter 2 Installation S LIRA TSS DPA 2 2 Unpacking Chassis and Power Supply Modulefs saamassa mme riit aan 2 2 smaili NEP CE ASIS liceali mA KS KA KS 2 3 Ridi POE P OM lalla 2 6 insialing BEFDE Chassis Mo a Rack a ai 2 7 Guidelines for Rackmount installalo asien 2 7 Rack Maui ER clio ai ii 2 8 Connecting the DFE POE CBL 2M Cable and AC Power Cord 2 9 DEEP SEE BL e CUP 2 9 A P ts aasad 2 12 Appendix A Specifications N POE Chassis SPEOIIGIUORNS Mt A 1 Port Troad Port 7 PIBOULDOSCPDDOEE oa iii ii ii a A 3 NPOE 1200 VESPE Al een A 4 ANSWERS alici A 5 BFEPOECBLEM Cable anna aaa A 5 IES RE at ai aaa cc A 5 Figures 1 1 1 2 1 3 2 1 2 2 2 3 2 4 2 5 2 6 2 7 A 1 Tables 1 1 2 1 2 2 2 3 2 4 A 1 A 2 A 3 A 4 A 5 Matrix N POE Chassis front and rear VIEW AAA N POE PSM Front Panel uper MP Example of a Simple N POE Power Configuration i x Removing a Chassis Bay Ever licia ia installing te POE PS
7. as long as the total power needed does not exceed the power output capability of the remaining N POE PSMs in the N POE Chassis e Provides a maximum power output of 1200 W to PoE switch modules The maximum number of PDs supported by each PoE switch module is dependent on the PD power consumption as indicated by their Power Classifications For details about Power Classification refer to Powered Devices PDs on page 1 4 Matrix N Series N POE Power System Installation Guide 1 3 N POE PSM Status LEDs e Provides power redundancy when two N POE PSMs are installed in the N POE Chassis and there is no more than a 1200 Watt demand by the connected DFE series switch module to support PDs So if one N POE PSM fails or is removed from the chassis the other N POE PSM can support the total load e Provides continuous power sharing by all N POE PSMs when two or more are installed in the N POE Chassis Up to four N POE PSMs can be installed in the N POE Chassis to provide up to 4800 Watts of power N POE PSM Status LEDs Powered There are two status LEDs AC power LED and DC power LED on each N POE PSM The AC power LED is green when the N POE PSM AC power input is within specifications and turns off when it is not The DC power LED is green when the N POE PSM 48 Vdc output is within specifications and turns off when it is not Devices PDs PDs are devices that receive their operating 48 Vdc power through a new or existing Ethernet
8. electricidad estatica The N POE Chassis is shipped with safety covers over each of the seven front panel 48 Vdc 25 A Maximum Outputs Ports 1 through 7 Do not remove a safety cover unless you plan to connect a DFE POE CBL 2M Cable Ports without a cable connected must have the safety cover installed to protect against an energy hazard care should be taken not to bridge the contacts of this connector The safety cover must remain in place until the N POE Cable is installed and connected to its corresponding module 1 Warning The rated output of these ports is 48 Vdc 25A This is an energy hazard and Advertencia La salida de estos puertos es 48 Vdc 25A Esto es un riesgo electrico y debe tenerse cuidado para no puentear los contactos de este conector La tapa de seguridad debe permanecer en su lugar hasta que el cable DFE POE CBL 2M sea instalado y conectado a su modulo correspondiente Warnhinweis Es liegen 48 V 25A Gleichspannung strom an diesen Ports an dies liegt im elektirschen Gefahrenbereich Es muf daf r Sorge getragen werden dass die Kontakte des Steckers nicht berbr ckt werden k nnen Die Schutzh llen m ssen aufgesteckt bleiben bis das DFE POE CBL 2M Kabel an das installierte Modul angeschlossen ist When you receive your N POE Chassis the chassis bay covers are in place over both power supply bays The bay covers have two purposes They provide an intake air ventilation path prevent EMI leakage and provide ac
9. package and prevails over any additional conflicting or inconsistent terms and conditions appearing on any purchase order or other document submitted by You Affiliate means any person partnership corporation limited liability company or other form of enterprise that directly or indirectly through one or more intermediaries controls or is controlled by or is under common control with the party specified This Agreement constitutes the entire understanding between the parties and supersedes all prior discussions representations understandings or agreements whether oral or in writing between the parties with respect to the subject matter of this Agreement The Program may be contained in firmware chips or other media BY INSTALLING OR OTHERWISE USING THE PROGRAM YOU REPRESENT THAT YOU ARE AUTHORIZED TO ACCEPT THESE TERMS ON BEHALF OF THE END USER IF THE END USER IS AN ENTITY ON WHOSE BEHALF YOU ARE AUTHORIZED TO ACT YOU AND YOUR SHALL BE DEEMED TO REFER TO SUCH ENTITY AND THAT YOU AGREE THAT YOU ARE BOUND BY THE TERMS OF THIS AGREEMENT WHICH INCLUDES AMONG OTHER PROVISIONS THE LICENSE THE DISCLAIMER OF WARRANTY AND THE LIMITATION OF LIABILITY IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT OR ARE NOT AUTHORIZED TO ENTER INTO THIS AGREEMENT ENTERASYS IS UNWILLING TO LICENSE THE PROGRAM TO YOU AND YOU AGREE TO RETURN THE UNOPENED PRODUCT TO ENTERASYS OR YOUR DEALER IF ANY WITHIN TEN 10 DAYS FOLLOWING THE DATE OF R
10. power outlet 3 Swap power cord for a known good one 4 Remove or replace affected N POE PSM 5 Contact Enterasys Networks for support Solid AC input to power supply is None within specification DC power LED Green Solid 48 Vdc power supply None output is within specification OFF 48 Vdc power supply output 1 Remove N POE PSM from is out of specification chassis 2 Contact Enterasys Networks for support Matrix N Series N POE Power System Installation Guide 2 15 Troubleshooting 2 16 Installation Specifications This appendix provides information about the following For information about Refer to page N POE Chassis Specifications A 1 Port 1 through Port 7 Pinout Description A 3 N POE 1200 W Specifications A 4 DFE POE CBL 2M Cable A 5 Compliance Standards A 5 Enterasys Networks reserves the right to change the specifications at any time without notice N POE Chassis Specifications Table A 1 provides the physical power and environmental specifications for the N POE Chassis Table A 1 N POE Chassis Specifications Item Specification Power Supply Slots PS 1 through PS 4 Slots for optional N POE 1200 W dc power supply modules Modules are hot swappable DC Outputs 48 Vdc Port 1 through Port 7 Provides operating status and 48 Vdc to N POE devices Output Voltage 48 0 Vdc Output Current 25 0 A Maximum Output Power 1200 W Matrix N Series N POE Power
11. required to correct the interference at his own expense WARNING Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Industry Canada Notice This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le present appareil num rique n met pas de bruits radiodlectrigues d passant les limites applicables aux appareils numeriques de la class A prescrites dans le Reglement sur le brouillage radiodlectrigue dict par le ministere des Communications du Canada Class A ITE Notice WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Clase A Aviso de ITE ADVERTENCIA Este es un producto de Clase A En un ambiente dom stico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas Klasse A ITE Anmerkung ACHTUNG Dieses Produkt z hlt zur Klasse A Industriebereich In Wohnbereichen kann es hierdurch zu Funkst rungen kommen daher sollten angemessene Vorkehrungen zum Schutz getroffen werden Product Safety This product complies with the following UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 IEC 60950 Se
12. 44 to 12 95 Watts 1 Optional 0 44 to 3 84 Watts 2 Optional 3 84 to 6 49 Watts 3 Optional 6 49 to 12 95 Watts 4 Not Allowed Reserved for Future Use Figure 1 3 shows an example of a simple configuration with one 48 Vdc output port from an N POE Chassis connected to a PoE switch module such as Enterasys Networks 7H4385 49 The N POE Chassis connection provides 48 Vdc and its power supply status information indicates if the power supply is okay to the PoE switch module Figure 1 3 Example of a Simple N POE Power Configuration 1 DTE non PoE compliant 6 PD Class 4 2 PD no Class rating 7 NPS 3 PD Class 2 8 48 Vdc Status cable DFE POE CBL 2M 4 PD Class 2 9 PoE compliant switch module 5 PD Class 3 Matrix N Series N POE Power System Installation Guide 1 5 Power Classifications and Deployment 1 6 Introduction The PoE switch module manages the 48 Vdc output to the six PDs In this example six of the PoE module 48 Vdc data ports are to PDs with the following Class ratings One does not support PoE no power One has no Class rating Defaults to Class 0 12 95 Watts maximum Two are Class 2 6 49 Watts maximum x 2 12 98 Watts total One is Class 3 12 95 Watts maximum One is Class 4 defaults to 12 95 Watts maximum The maximum power needed from the N POE Chassis is 51 83 Watts In this example only one N POE PSM would be needed in the N POE Chassis Howe
13. 9 power cord connector This is for connection to an AC Inlet connector on N POE Chassis Plug Type As required in country of installation Wire Gauge 12 AWG with 2 mm wires Voltage Rating 250 Volts minimum Power Cord Power cord must be constructed with molded connectors at both ends Construction DFE POE CBL 2M Cable This cable is a PoE compliant ferrite shielded cable terminated with 13W3 male and female D Sub connectors This cable is currently available in a 2 meter length and must be ordered separately This cable provides the 48 Vdc operating voltages and operating status information from each 48 Vdc 25 A outputs PS 1 through PS 7 on the N POE Chassis front panel to the attached N PoE switch device Compliance Standards The N POE and N POE PSM meet the safety and electromagnetic compatibility EMC requirements listed in Table A 5 Table A 5 Compliance Standards Compliance Standards Safety UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 IEC 60950 Electromagnetic Compatibility EMC 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC Applies to RPS system with five EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 modules installed and working with five AS NZS CISPR 22 VCCI V 3 network devices Matrix N Series N POE Power System Installation Guide A 5 Compliance Standards A 6 Specifications
14. Commercial Computer Software Restricted Rights Clause and its successors and iii in all respects is proprietary data belonging to Enterasys and or its suppliers For Department of Defense units the Program is considered commercial computer software in accordance with DFARS section 227 7202 3 and its successors and use duplication or disclosure by the Government is subject to restrictions set forth herein 6 DISCLAIMER OF WARRANTY EXCEPT FOR THOSE WARRANTIES EXPRESSLY PROVIDED TO YOU IN WRITING BY Enterasys Enterasys DISCLAIMS ALL WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY SATISFACTORY QUALITY FITNESS FOR A PARTICULAR PURPOSE TITLE AND NON INFRINGEMENT WITH RESPECT TO THE PROGRAM IF IMPLIED WARRANTIESMAY NOT BE DISCLAIMED BY APPLICABLE LAW THEN ANYIMPLIED WARRANTIES ARE LIMITED IN DURATION TO THIRTY 30 DAYS AFTER DELIVERY OF THE PROGRAM TO YOU 7 LIMITATION OF LIABILITY IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION SPECIAL INCIDENTAL CONSEQUENTIAL OR RELIANCE DAMAGES OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THIS FOREGOING LIMITATION SHALL APPLY REGARDLESS OF THE CAUSE OF ACTION UNDER WHICH DAMAGES ARE SOUGHT THE
15. ECEIPT FOR A FULL REFUND IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT CONTACT ENTERASYS NETWORKS LEGAL DEPARTMENT AT 978 684 1000 You and Enterasys agree as follows 1 LICENSE You have the non exclusive and non transferable right to use only the one 1 copy of the Program provided in this package subject to the terms and conditions of this Agreement 2 RESTRICTIONS Except as otherwise authorized in writing by Enterasys You may not nor may You permit any third party to i Reverse engineer decompile disassemble or modify the Program in whole or in part including for reasons of error correction or interoperability except to the extent expressly permitted by applicable law and to the extent the parties shall not be permitted by that applicable law such rights are expressly excluded Information necessary to achieve interoperability or correct errors is available from Enterasys upon request and upon payment of Enterasys applicable fee ii Incorporate the Program in whole or in part in any other product or create derivative works based on the Program in whole or in part iii Publish disclose copy reproduce or transmit the Program in whole or in part iv Assign sell license sublicense rent lease encumber by way of security interest pledge or otherwise transfer the Program in whole or in part v Remove any copyright trademark proprietary rights disclaimer or warning notice included on or embedded
16. M ammua a rada E ii 2 Fastening the N POE Chassis to the Rack eiie eis aan gii Breaker OSO uns ee DFE POE CBL 2M Cable Connections PEK TER SR RR aura I SR DO AC Pewar PROBIERE ci baltici 1 Matrix N POE Chassis Status LEDs and Circuit BreakersS sommes 2 14 48 Vdc D Sub Female Front Panel Port Connector PiNOUtS n A 3 DTE PoE Power Classifications Mm i Contents of N POE ey COON ss ai Power Distribution pp to Number of Installed Power Fr N FRE PSM Status LER TOONS and Recommended Actions 2 1 N POE 1200 Bb nou Dewar e maps de AG Power Gord Specific lOs ausser Compliance SLAPS cuoi tas ete tos aee Re ob e ao in pote Peta Me utere A About this Guide This guide provides an overview installation and troubleshooting instructions and specifications for the Enterasys Matrix N POE power system which can provide up to seven 48 Vdc power sources to DFE series PoE compliant switch modules in an N3 or N7 network system chassis Using This Guide Read through this guide completely to familiarize yourself with its contents and gain an understanding of the features and capabilities of the N POE power system NPS components A general working knowledge of data communications networks is helpful when setting up an NPS Who Should Use This Guide This guide is intended for a network administrator responsible for installing and se
17. Matrix N Series N POE Power System Installation Guide PEZZI RR OR ER TTTTTER IR RER III loterecereterecererererececoco OOO PREIS 9 enterasy 9033952 04 Networks that Know Electrical Hazard Only qualified personnel should perform installation procedures AN Riesgo Electrico Solamente personal calificado debe realizar procedimientos de instalacion Elektrischer Gefahrenhinweis Installationen sollten nur durch ausgebildetes und gualifiziertes Personal vorgenommen werden Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made The hardware firmware or software described in this document is subject to change without notice IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL INDIRECT SPECIAL OR CONSEOUENTIAL DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING OUT OF OR RELATED TO THIS DOCUMENT WEB SITE OR THE INFORMATION CONTAINED IN THEM EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF KNEW OF OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES Enterasys Networks Inc 50 Minuteman Road Andover MA 01810 2005 Enterasys Networks Inc All rights reserved Part Number 9033952 04 February 2005 E
18. NTERASYS NETWORKS ENTERASYS MATRIX LANVIEW MATRIX NETSIGHT WEBVIEW and any logos associated therewith are trademarks or registered trademarks of Enterasys Networks Inc in the United States and other countries All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies Documentation URL http www enterasys com support manuals Documentacion URL http www enterasys com support manuals Dokumentation http www enterasys com support manuals Regulatory Compliance Information Federal Communications Commission FCC Notice This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment uses generates and can radiate radio frequency energy and if not installed in accordance with the operator s manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user will be
19. System Installation Guide A 1 N POE Chassis Specifications A 2 Specifications Table A 1 N POE Chassis Specifications continued Item Specification Physical Dimensions without mounting brackets Dimensions with mounting brackets Approximate Weight Unit MTBF 12 9 H x 44 6 W x 39 73 D cm 5 12 Hx 17 56 W x 15 7 D in 12 9Hx 48 2 W x 39 73 D cm 5 12 H x 18 98 W x 15 70 D in 8 2 kg 18 0 Ib 1 306 387 hours Electrical AC power reguirement per AC INLET connection Input Freguency Input Voltage Range Max Amp Four AC inputs one for each N POE 1200 W installed Each input AC INLET 1 through INLET 4 require the following power for N POE 1200 W power supplies installed in slots PS 1 through PS 4 respectively 50 60 Hz 50 60 Hz 100 to 125 Vac 15 A per 200 to 240 Vac 8 A per power supply power supply Environmental Operating Temperature Storage Temperature 5 C to 40 C 41 F to 104 F 30 C to 73 C 22 F to 164 F Port 1 through Port 7 Pinout Description Port 1 through Port 7 Pinout Description For pin location and function refer to Figure A 1 and Table A 2 respectively Figure A 1 48 Vdc D Sub Female Front Panel Port Connector Pinouts Table A 2 48 Vdc D Sub Pinout Description Name Number Function Power A1 None PS 1 1 48 Vdc Output OK PS 1 2 5Vdc PS2 3 48 Vdc Output OK PS2 4 5 Vdc PS3
20. arton and compare the contents shipped with those listed in Table 2 1 and Table 2 2 3 Perform a visual inspection of the devices for any signs of physical damage Contact Enterasys Networks if there are any signs of damage Refer to Getting Help on page 1 7 for details Table 2 1 Contents of N POE Chassis Carton Item Quantity N POE Chassis 1 Manual Accessory Kit 1 Reusable ESD Wrist Strap 1 Table 2 2 Contents of an Optional N POE PSM Carton Item Quantity N POE 1200 W DC Power Supply Module 1 USA NEMA Power Cord 5 20 C19 R A SHLD 1 Notice Card 1 1 If a power cord needs to be replaced it must meet the requirements specified in AC Power Cord on page A 5 Note The DFE POE CBL 2M Cable power cables used to make connections from the N POE Chassis to the N PoE switch modules must be ordered separately 2 2 Installation Installing N POE PSMs Installing N POE PSMs Before installing the N POE Chassis in a rack refer back to Powered Devices PDs on page 1 4 to determine how many N POE PSMs will be needed in the N POE Chassis One box with an N POE PSM is shipped separately from the N POE Chassis Additional N POE PSMs are ordered separately Caution Observe all Electrostatic Discharge ESD precautions when handling sensitive electronic eguipment Precauci n Al trabajar con eguipos electr nicos sensibles tome todas las precauciones de seguridad para evitar descargas de
21. cable from a switch or other device that can provide a PoE compliant port connection This enables the PD to operate in a location without local power For example e Devices such as PoE compliant remote EXIT signs and Personal Data Assistants PDAs e Devices that support Voice over IP such as PoE compliant digital telephones e Devices that support Wireless Application Protocol WAP such as security cameras laptop PCs and many more devices Each device is rated according to a PoE Power Classification assigned by the manufacturer If you know the classification of the PDs connected to your system you can approximate the total amount of power needed to operate the PDs and plan accordingly Power Classifications and Deployment 1 4 Introduction The number of N POE PSMs needed to power the PoE compliant PDs is dependent on their Power Classifications Each N POE PSM can supply up to 1200 Watts of power You can determine the number of power supplies needed by referring to Table 1 1 and adding up the maximum power requirement according to the Power Classification rating 1 through 3 of each PD Keep in mind that each classification represents a range of power so your maximum calculation represents a worst case power consumption so the actual power consumption could be less Power Classifications and Deployment Table 1 1 DTE PoE Power Classifications DTE Maximum Power Class Usage Range Usage 0 Default 0
22. cess to the two PSM slots in each chassis bay The left bay has power supply slots 1 and 2 the right bay slots 3 and 4 As shown in Table 2 3 when two to four PSMs are installed the power supplies share the load equally and provide power redundancy If one power supply fails or is removed hot swapped for any reason the other power supplies take up the load Power redundancy remains in effect as long as the load does not exceed the power as stated in the Redundancy column Matrix N Series N POE Power System Installation Guide 2 3 Installing N POE PSMs 2 4 Installation Table 2 3 Power Distribution According to Number of Installed Power Supplies Power Hot Redundan Power Sharin Supplies ne elu Swappable ower ananing 1 No No Maximum power 1200 2 Yes if power demand is Yes The total load is shared by both power less than 1200 Watts supplies 3 Yes if power demand is Yes The total load is shared by the three power less than 2400 Watts 1 supplies 4 Yes if power demand is Yes The total load is shared by the four power less than 3600 Watts supplies 1 If power requirements exceed this Wattage power redundancy is no longer supported Removing a power supply under this condition will cause the remaining power supplies to go into over current protection and shut down the power system To install the N POE PSMs proceed as follows 1 2 Note To prevent EMI leakage from the N POE Chassis
23. d transferees successors and assigns as permitted by this Agreement Any attempted assignment transfer or sublicense in violation of the terms of this Agreement shall be void and a breach of this Agreement 12 WAIVER A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing and will not be construed as a waiver of any subsequent breach of such term or condition Enterasys failure to enforce a term upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion 13 SEVERABILITY In the event any provision of this Agreement is found to be invalid illegal or unenforceable the validity legality and enforceability of any of the remaining provisions shall not in any way be affected or impaired thereby and that provision shall be reformed construed and enforced to the maximum extent permissible Any such invalidity illegality or unenforceability in any jurisdiction shall not invalidate or render illegal or unenforceable such provision in any other jurisdiction 14 TERMINATION Enterasys may terminate this Agreement immediately upon Your breach of any of the terms and conditions of this Agreement Upon any such termination You shall immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program vii viii Contents About this Guide eo eee Ic E xi Vibo Shod Uss TAS aul en ee
24. e pudiera resultar en lesi n corporal o la muerte debido a un riesgo el ctrico Elektrischer Gefahrenhinweis Warnung vor s mtlichen Handlungen die zu Verletzung von Personen oder Todesf llen hervorgerufen durch elektrische Spannung f hren k nnen l Warning Warns against an action that could result in personal injury or death Advertencia Advierte contra una acci n que pudiera resultar en lesi n corporal o la muerte Warnhinweis Warnung vor Handlungen die zu Verletzung von Personen oder gar Todesf llen f hren k nnen Matrix N Series N POE Power Supply System Installation Guide xiii Conventions Used in This Guide xiv About this Guide Introduction This chapter provides a functional overview of the N POE system which includes the following For information about Refer to page N POE Power System NPS Overview 1 2 N POE Chassis 1 3 Optional N POE Power Supply Module N POE PSM 1 3 N POE PSM Status LEDs 1 4 Powered Devices PDs 1 4 Power Classifications and Deployment 1 4 Getting Help 1 7 Note In this document the following terms are used NPS refers to the complete N POE power system N POE Chassis refers to the N POE Chassis only e N POE PSM refers to the N POE 1200 W DC power supply module PoE refers to the Power over Ethernet 802 3af compliance standard PoE switch module refers to a DFE Series PoE compliant switch module PDrefers to
25. ector is used 2 Plug the other end of the AC power cord into a separately fused AC power outlet that meets the power specifications provided in Appendix A 3 Check to see if the DC power LED is green and the AC power LED is green Otherwise refer to Troubleshooting on page 2 14 to determine the problem 4 Iftwo or more power supplies are being installed repeat steps 1 through 3 for each N POE PSM If you need additional help contact Enterasys Networks Refer to Getting Help on page 1 7 for instructions Connecting the DFE POE CBL 2M Cable and AC Power Cord Figure 2 6 AC Power Connections RAR RORRRARRRAR SASASAZARARARO SS RSS III CRORE RO ORO RO ORO ROO OGD RD SR GLI e902090209090502090209030909 0 TI O 0 0 0 0 0 0 0 0 0 O Q 0 O0 0 FOUR POWER SUPPLY CORDS BEFORE SEAMEMGTO AVOID ELECTRIC SHOCK WARTUNGSAPDETEN DIE 4 ETZANSCHLUSSE VOM NETZ UM ELEKTRISCHE SCHLAGE AC INLETS O LORO RAR RRA RRA ARAARA cocecoracesereceserecerececori ERROR ROO ROO LILLE CRORORORORORORORORORORO ROO RR CERRAR ar 1 AC power cord 2 AC INLET 1 power connector rear of chassis 3 AC power source O AGINLETI CRORERER ERR ROR RRR RRR OR SEED SAK HOHHOI 29292925 TR REED AIROK OKK OH OHO OHO OHO RER IRRE en RER Poses ACINLET2 es e RE OOO OOOO 4 DC power LED 5 AC power LED Matrix N Series N POE Power S
26. ed back in Installing N POE PSMs on page 2 3 rack mount the N POE Chassis as follows 1 Refer to the installation guidelines Guidelines for Rackmount Installation on page 2 7 Install the N POE Chassis into the rack Rack Mounting the Chassis on page 2 8 Connect the DFE POE CBL 2M power cables DFE POE CBL 2M Cable on page 2 9 Connect the AC power cords AC Power Cord on page 2 12 Guidelines for Rackmount Installation The installation site must be within reach of the network cabling and meet the requirements listed below Ensure that the NPS is located close enough to connect 2 meter 6 6 foot DFE POE CBL 2M cables from the N POE PSMs to the N POE switch modules Ensure that you order sufficient DFE POE CBL 2M cables for your installation Up to seven cables may be needed depending on how many N POE modules you plan to use in your system s N3 or N7 chassis Need one to four three pronged power receptacles capable of delivering the current and voltage specified in N POE 1200 W Specifications on page A 4 Up to four AC outlets on independently fused circuits are required and must be located within 182 centimeters 6 feet from the site The power cords used and type of outlet are dependent on the country In the United States one power cord with a NEMA 5 20P plug is provided with each N POE PSM An ambient temperature of between 5 C 41 F and 40 C 104 F must be maintained at
27. es de conectar los cables DFE POE CBL 2M cologue los interruptores de circuito asociados a los puertos de salida de 48 voltios conectados a la m dulos de las series N POE en la posici n de OFF apagado Por ejemplo deber colocar en OFF el BKR2 si ste est conectado a un cable del Puerto 2 Matrix N Series N POE Power System Installation Guide 2 9 Connecting the DFE POE CBL 2M Cable and AC Power Cord 2 10 Installation A Warning The rated output of these ports is 48 Vdc 25A This is an energy hazard and care should be taken not to bridge the contacts of this connector The safety cover must remain in place until the N POE Cable is installed and connected to its corresponding module Advertencia La salida de estos puertos es 48 Vdc 25A Esto es un riesgo electrico y debe tenerse cuidado para no puentear los contactos de este conector La tapa de seguridad debe permanecer en su lugar hasta que el cable DFE POE CBL 2M sea instalado y conectado a su modulo correspondiente Warnhinweis Es liegen 48 V 25A Gleichspannung strom an diesen Ports an dies liegt im elektirschen Gefahrenbereich Es mu daf r Sorge getragen werden dass die Kontakte des Steckers nicht berbr ckt werden k nnen Die Schutzh llen m ssen aufgesteckt bleiben bis das DFE POE CBL 2M Kabel an das installierte Modul angeschlossen ist Remove and save the two screws fastening the safety cover protecting the 48 Volt OPTIONAL POWER INPUT connector
28. guridad del Producto El producto de Enterasys cumple con lo siguiente UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 IEC 60950 Produktsicherheit Dieses Produkt entspricht den folgenden Richtlinien UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 IEC 60950 Electromagnetic Compatibility EMC This product complies with the following 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 VCCI V 3 Compatibilidad Electromagnetica EMC Este producto de Enterasys cumple con lo siguiente 47 CFR Partes 2 y 15 CSA C108 8 89 336 EEC EN 55022 EN 55024 EN 61000 3 2 EN 61000 3 3 AS NZS CISPR 22 VCCI V 3 Elektro magnetische Kompatibilit t EMC Dieses Produkt entspricht den folgenden Richtlinien 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 VCCI V 3 VCCI Notice This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions COB EEULLESEKESA FRS VCCI DATE KEKO lt ZTSAXAMMKINEETI TOHEZXZXKERH CHATS CBR RABS TZEAN ET TOBE EMER AS ZEDBRANSTEMHOVET BSMI EMC Statement Taiwan This is a class A product In a domestic environment this product may cause radio inte
29. i n para reducir la interferencia electromagn tica del chasis 6 Proceed to Installing N POE Chassis into a Rack on page 2 7 for the rack mount installation instructions Figure 2 1 Removing a Chassis Bay Cover 1 Captive Screw Phillips head 2 3 Chassis bay left 2 Bay Cover Figure 2 2 Installing the N POE PSM 1 N POE Chassis 3 Power supply slot PS1 2 N POE PSM 4 Captive screw Phillips head Matrix N Series N POE Power System Installation Guide 2 5 Installing N POE PSMs 2 6 Replacing an N POE PSM Installation To replace an N POE PSM in an operating N POE Chassis proceed as follows Caution Observe all Electrostatic Discharge ESD precautions when handling sensitive AN electronic eguipment If power requirements exceed this Wattage as stated in Table 2 3 on page 2 4 power redundancy is no longer supported Removing a power supply under this condition will cause the remaining power supplies to go into over current protection and shut down the power system Precauci n Al trabajar con equipos electr nicos sensibles tome todas las precauciones de seguridad para evitar descargas de electricidad estatica Si los requerimientos de la fuente de poder fueran superiores a la potencia especificada en Table 2 3 on page 2 4 tenga en cuenta que el poder alternativo ya no funcionar Si quita la f
30. in any part of the Program 3 APPLICABLE LAW This Agreement shall be interpreted and governed under the laws and in the state and federal courts of the Commonwealth of Massachusetts without regard to its conflicts of laws provisions You accept the personal jurisdiction and venue of the Commonwealth of Massachusetts courts None of the 1980 United Nations Convention on Contracts for the International Sale of Goods the United Nations Convention on the Limitation Period in the International Sale of Goods and the Uniform Computer Information Transactions Act shall apply to this Agreement 4 EXPORT RESTRICTIONS You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U S Government including the U S Department of Commerce which prohibit export or diversion of certain technical products to certain countries unless a license to export the Program is obtained from the U S Government or an exception from obtaining such license may be relied upon by the exporting party If the Program is exported from the United States pursuant to the License Exception CIV under the U S Export Administration Regulations You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes If the Program is exported from the United States pursuant to the License Exception TSR under the U S Export Administration Regulations in addition to the restric
31. ote powered devices PDs such as telephones fax machines and other devices that meet PoE standards The N POE Series switch manuals explain how to install the switch connect the 48 Vdc data cables to the external powered devices PDs and configure the switch using command line interface commands described in the Matrix DFE Series Configuraton Guide Each manual is written for qualified personnel who are responsible for installing the switch device and also have a general working knowledge of data communication networks and their physical layer components The manuals can be accessed on the World Wide Web using the following URL Documentation URL http www enterasys com support manuals Documentacion URL http www enterasys com support manuals Dokumentation http www enterasys com support manuals About this Guide Conventions Used in This Guide Conventions Used in This Guide The following conventions are used in this guide Note Calls the reader s attention to any item of information that may be of special importance Caution Contains information essential to avoid damage to the equipment Precauci n Contiene informaci n esencial para prevenir da ar el equipo Achtung Verwei t auf wichtige Informationen zum Schutz gegen Besch digungen Electrical Hazard Warns against an action that could result in personal injury or death AN due to an electrical hazard Riesgo Electrico Advierte contra una acci n qu
32. powered devices which can operate using 48 Vdc received through new or existing Ethernet data cable Matrix N Series N POE Power System Installation Guide 1 1 N POE Power System NPS Overview N POE Power System NPS Overview The N POE Chassis can house up to four N POE PSMs to provide an N POE Power System to meet your needs and can consist of the following components 1 2 Introduction One N POE Chassi S One to four optional N POE PSMs Each are shipped with their own AC power cord One to seven optional DFE POE CBL 2M Cables The NPS enables you to expand the capability of the Matrix N3 and Matrix N7 chassis to operate Enterasys PoE switch modules which support connections to powered devices PDs This is accomplished by providing the 48 Vdc necessary for the PoE switch modules to support 48 Vdc data connections to powered devices PDs The N POE Chassis and N POE PSM are shown in Figure 1 1 and Figure 1 2 respectively Figure 1 1 Matrix N R OWN POE Chassis front and rear view ERRRRRREO OO EHE RBB RR EEEEHEEEHEHEHEEEEREEE E ER IT FIBRA EEE EIER ED O 0 0 0 0 0 0 0 0 0 0 O O 0 0 e o O BORRAR RRA ACINLETA Acer BR RRR RER PS SERRA o2020202020202020202020 0202 o SIERT CRORE ROR rr 0909 SEIT ER 0000000000000 0000000020202 RD OAO OHO OHHOH OHO OKO ARSS OSOS OOOO 90000000 g
33. rference in which case the user may be required to take adequate measures SARA EST NENEm TAERE EMIK WP BARATTE CEEP T PRASRE KE Hy 3 tes ut BS SN SE Declaration of Conformity Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Address Conformance to Directive s Product Standards Equipment Type Environment 89 336 EEC 73 23 EEC Enterasys Networks Inc 50 Minuteman Road Andover MA 01810 USA Enterasys Networks Ltd Nexus House Newbury Business Park London Road Newbury Berkshire RG14 2PZ England EC Directive 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 EC Directive 73 23 EEC EN 60950 Networking Equipment for use in a Commercial or Light Industrial Environment Enterasys Networks Inc declares that the equipment packaged with this notice conforms to the above directives Enterasys Networks Inc Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT This document is an agreement Agreement between the end user You and Enterasys Networks Inc on behalf of itself and its Affiliates as hereinafter defined Enterasys that sets forth Your rights and obligations with respect to the Enterasys software program firmware installed on the Enterasys product including any accompanying documentation hardware or media Program in the
34. t EEE EEE RER PILL IIND BRASS UH EEE OSOS OSOS gi RER REED RA RA IR le se 2 ORORO ORD 7 focoso e RAR III SEITZ PRES FILI AD VA A ae 97070071 O SPSS N POE Chassis front Seven D Sub 48 Vdc output ports Ports 1 7 Power supply bay cover Power supply bay PS1 N POE PSM installed N e O O 5 25A circuit breakers for each N POE PSM 6 N POE Chassis rear view 7 Air discharge vents 2 8 Four AC power input connectors view shown with an optional N POE Chassis Figure 1 2 N POE PSM Front Panel amp 1 Intake cooling fan 3 Handle 2 Green DC power LED DC within 4 Red AC power LED AC out of specification specification N POE Chassis The N POE Chassis features include the following e Supports up to four N POE PSMs in an N 1 configuration if two or more N POE PSMs are installed and one fails power is provided by the remaining N POE PSMs e Easy front panel access to seven D Sub 48 Vdc 25 A connectors that can provide power for up to seven PoE switch modules residing in an N3 or N7 chassis e Easy access to circuit breaker reset switch for each 48 Vdc 25 A output Separate AC power inlet connectors for each N POE PSM installed e Installs in a standard 19 inch rack to provide maximum wiring closet port density Optional N POE Power Supply Module N POE PSM The N POE PSM features include the following e Hot swappable capability
35. the installation site with fluctuations of less than 10 C 18 F per hour Caution To ensure proper ventilation and prevent overheating leave a minimum clearance space of 10 16 cm 4 0 in at the front and rear of the N POE Chassis Precauci n Para asegurar una buena ventilaci n y evitar que el sistema se sobrecaliente deje un espacio minimo de 10 16 cm 4 pulgadas con respecto a la parte delantera y trasera del chasis N POE Matrix N Series N POE Power System Installation Guide 2 7 Installing N POE Chassis into a Rack Warning Before installing the chassis into a rack ensure that the rack can support the device s without compromising the stability of the rack Otherwise personal injury and or equipment damage may result Advertencia Antes de instalar el chassis en un rack asegurarse que el rack puede soportar el los dispositivo s sin comprometer la estabilidad del mismo De otra forma puede suceder algun tipo de dafio personal o del equipo Warnhinweis Sch tzen Sie sich vor Verletzungen und Ger teschaden berzeugen Sie sich vor der Installation des Chassis in das Rack von dessen Stabilit t Rack Mounting the Chassis Refer to Figure 2 3 and proceed as follows to install the N POE Chassis into a 19 inch rack 1 Position the chassis between the vertical frame members and align the mounting holes in the chassis brackets with those in the rack frame 2 Fasten the chassis securely to the frame using eight mo
36. tion on transfer set forth in Sections 1 or 2 of this Agreement You agree not to i reexport or release the Program the source code for the Program or technology to a national of a country in Country Groups D 1 or E 2 Albania Armenia Azerbaijan Belarus Bulgaria Cambodia Cuba Estonia Georgia Iraq Kazakhstan Kyrgyzstan Laos Latvia Libya Lithuania Moldova North Korea the People s Republic of China Romania Russia Rwanda Tajikistan Turkmenistan Ukraine Uzbekistan Vietnam or such other countries as may be designated by the United States Government ii export to Country Groups D 1 or E 2 as defined herein the direct product of the Program or the technology if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or iii if the direct product of the technology is a complete plant or any major component of a plant export to Country Groups D 1 or E 2 the direct product of the plant or a major component thereof if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or is subject to State Department controls under the U S Munitions List 5 UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed Program i was developed solely at private expense ii contains restricted computer software submitted with restricted rights in accordance with section 52 227 19 a through d of the
37. trouble if known The device history i e have you returned the device before is this a recurring problem etc Any previous Return Material Authorization RMA numbers Matrix N Series N POE Power System Installation Guide 1 7 Getting Help 1 8 Introduction Installation Electrical Hazard Only qualified personnel should perform installation procedures Riesgo Electrico Solamente personal calificado debe realizar procedimientos de instalacion Elektrischer Gefahrenhinweis Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden This chapter provides the installation instructions to install all the components of an NPS To correctly install an NPS follow the order of information listed below For information about Refer to page Required Tools 2 2 Unpacking Chassis and Power Supply Module s 2 2 Installing N POE PSMs 2 3 Installing N POE Chassis into a Rack 2 7 Connecting the DFE POE CBL 2M Cable and AC Power Cord 2 9 Troubleshooting 2 14 Matrix N Series N POE Power System Installation Guide 2 1 Required Tools Required Tools A Phillips screwdriver is required to install the N POE Chassis and Allen wrench for the N POE PSMs Unpacking Chassis and Power Supply Module s To unpack the N POE Chassis or an N POE PSM proceed as follows 1 Open the box and remove the packing material protecting the devices 2 Verify the contents of each c
38. tting up the switch Electrical Hazard Only qualified personnel should install or service this unit Riesgo El ctrico Nada mas personal capacitado debe de instalar o darle servicio a esta unida Elektrischer Gefahrenhinweis Installationen oder Servicearbeiten sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden Matrix N Series N POE Power Supply System Installation Guide xi How to Use This Guide How to Use This Guide For Refer to An overview of the features and capabilities of the Chapter 1 Introduction NPS introduction to powered devices PDs and Power Classification and power system deployment This chapter also provides instructions for obtaining help from Enterasys Networks if needed Instructions to install an NPS into a standard Chapter 2 Installation 19 inch rack This includes installing the N POE Chassis one to four N POE PSMs interconnecting DFE POE CBL 2M 48 Vdc Cables and AC power cords Troubleshooting is also covered in this chapter Specifications environmental requirements and Appendix A Specifications physical properties of the N POE Chassis N POE PSM N POE 1200W power supply DFE POE CBL 2M 48 Vdc Cable 48 Vdc Port D sub pin out description and Compliance Standards Using the Matrix N Series Manual Set xii The Matrix N POE Series of switches support PoE compliant 48 Vdc data connections through the same cable to rem
39. uente de poder en esas condiciones har que el resto de las fuentes entren en modo de protecci n de exceso de corriente y el sistema se apagar 1 Unplug the AC power cord going from the AC power oulet to the N POE Chassis AC INLET connector associated with the N POE PSM being removed For example if removing the N POE PSM in power supply slot PS1 unplug the AC INLET 1 power cord from the AC outlet 2 At the bay opening where the PSM module slot is located loosen the captive Phillips head screw securing the N POE PSM until the N POE PSM is released from the N POE Chassis 3 Pull out on the N POE PSM front panel handle to remove the N POE PSM from the N POE Chassis 4 Repeatsteps 1 through 3 for each additional N POE PSM you plan to remove Note If you plan to remove and not replace an N POE PSM immediately reinstall the bay cover over the empty power supply slots to prevent EMI leakage from the N POE Chassis To install an N POE PSM refer to steps 1 through 3 in Installing N POE PSMs on page 2 3 Perform those steps for each N POE PSM being replaced When those steps are completed proceed to Connecting the DFE POE CBL 2M Cable and AC Power Cord on page 2 9 Installing N POE Chassis into a Rack Installing N POE Chassis into a Rack To install the N POE Chassis in a 19 inch rack you need four user supplied screws to fasten the N POE Chassis to the rack rails After installing the N POE PSM s as describ
40. unting screws user supplied Figure 2 3 Fastening the N POE Chassis to the Rack 1 Rails of 19 inch rack 2 Mounting screws supplied by user 2 8 Installation Connecting the DFE POE CBL 2M Cable and AC Power Cord Connecting the DFE POE CBL 2M Cable and AC Power Cord DFE POE CBL 2M Cable The N POE Chassis 48 Volt Output Ports 1 through 7 are connected to Enterasys Ethernet N POE series switch modules using DFE POE CBL 2M cables In the following procedure to connect an DFE POE CBL 2M cable the appropriate circuit breaker needs to be set to OFF and reset to ON Circuit Breaker Operation To set a circuit breaker to the OFF position Figure 2 4 use a non metallic tool to press the OFF switch This breaks the circuit and causes the ON rocker button to pop up To reset the circuit breaker press on the ON rocker switch Figure 2 4 Circuit Breaker Operation 1 OFF switch breaks the circuit 3 Rockerswitch shown pressed in ON 2 Rocker switch pops up when OFF switch is pressed Connecting the DFE POE CBL 2M Cable To connect a DFE POE CBL 2M cable refer to Figure 2 5 and proceed as follows circuit breakers associated with the 48 Volt Output Ports being connected to N POE series i Caution Before connecting any DFE POE CBL 2M cables set to the OFF position those switch modules For example you would set BKR2 to OFF if connecting a cable to Port 2 Precauci n Ant
41. ver as an option a second N POE PSM can be installed for redundancy As long as N POE PSMs are sharing a load of under 1200 Watts one N POE PSM can handle the load if the other fails or is removed from the N POE Chassis Getting Help Getting Help For additional support related to the devices or this document contact Enterasys Networks using one of the following methods World Wide Web http www enterasys com support Phone 603 332 9400 1 800 872 8440 toll free in U S and Canada For the Enterasys Networks Support toll free number in your country http www enterasys com support gtac all html Internet mail support enterasys com To expedite your message please type switching in the subject line To send comments or suggestions concerning this document to the Technical Writing Department techwriting enterasys com To expedite your message please include the document Part Number in the email message Before contacting Enterasys Networks for technical support have the following information ready Your Enterasys Networks service contract number A description of the failure A description of any action s already taken to resolve the problem e g changing mode switches rebooting the unit etc The serial and revision numbers of all involved Enterasys Networks products in the network A description of your network environment layout cable type etc Network load and frame size at the time of
42. ystem Installation Guide 2 13 Troubleshooting Troubleshooting 2 14 Installation Figure 2 7 shows the chassis front and rear panel the location of the status LEDs and the circuit breakers BKR 1 through BKR 7 used to protect or manually disconnect the power to the seven 48 Vdc output Ports 1 through 7 Refer to Table 2 4 for a functional description of each LED and recommended actions to solve a problem Note In Figure 2 7 the bay cover is removed for clarity Figure 2 7 Matrix N POE Chassis Status LEDs and Circuit Breakers RRR ORR ERR 2 2 2 0 OR ORO gt S Y2 9095969595959 OPAS ooo ORO OBRA OO OO OHO OH OHO R O 1 DC power good LED green 4 Circuit breaker button in OFF position 2 AC power failure LED red 5 Circuit breaker button in ON position 3 Circuit breaker OFF switch use non metallic press to ON to provide power to tool to reach and depress switch to disconnect associated 48 Vdc Output Port 1 7 power from the associated 48 Vdc Output Port 1 7 The circuit breaker button pops up to OFF position Troubleshooting Table 2 4 N POE PSM Status LED Indications and Recommended Actions LED Color State Recommended Action AC power LED Green Off AC input power to power supply is off or out of specification 1 Check AC power cord connection to the power supply 2 Check AC power at the
Download Pdf Manuals
Related Search