Hunter 27185 Remote Control - Hunter 27185 Remote Control
Contents
1. Most installations will be one of these four types Canopy Hanger Hunter Hands Free Canopy Low Profile Styles and Il or Bracket Hanger 5 Install the ceiling fan according to its instructions up to the point of making the electrical connections Connect receiver to ceiling fan according to the mounting type as instructed in Figure 2 6 If the fan is already installed turn the power OFF at the main electrical panel Reverse the installation procedure according to the fan instructions to the point of disconnecting the fan wiring Connect the receiver to the ceiling fan according to the mounting type as instructed in Figure 2 7 Use the 2 large wire nuts supplied to connect the receiver and house wiring then use the 3 small wire nuts supplied to connect the receiver and ceiling fan wiring Refer to the Wiring Diagram in Figure 3 Figure 1 Receiver Back ON DIP m 234 Dip Switch CFL INC Switch shown in CFL position Transmitter Back 8 Be sure the antenna is positioned securely so it can not interfere with the ceiling fan motor Refer to Figure 2 Do not modify or damage the antenna wire as control performance may be reduced After securing the receiver antenna and wiring finish hanging the ceiling fan according to its instructions 9 Restore power at main electrical panel Transmitter Installation 1 Install2. decrease from maximum brightness to OFF Release the light button when the desired light level is reached Continue to hold the light button to repeat the cycle Maximum light level decrease OFF While the light is ON holding the light button will decrease the light brightness Turning the light OFF resets the dimming function The next press of the light button will start at maximum brightness 2 Fan Operation Press the High Medium or Low speed buttons to turn the ceiling fan ON at the desired speed Press the fan OFF key to turn the ceiling fan OFF For best fan operation Start the fan on High and then select the desired speed Symptom Possible Causes 1 No functions operate Main Power not restored Solution Replace fuse Turn ON circuit breaker Turn ON wall switch Fan pull chain not set to High Se fan pull chain to High speed Light pull chain not set to ON Se ight kit to ON Receiver wiring incorrect Verify wiring connections Transmitter and receiver dip switches do not match Se transmitter and receiver to same dip switch setting Battery too weak 2 Operates only at close range Signal blocked from reaching receiver Replace with new 9 Volt alkaline battery Extend antenna into ceiling box or move it for better reception Battery too weak 3 Inconsistent operation Signal partially blocked from reaching receiver Replace
3. with new 9 Volt alkaline battery Extend antenna into ceiling box or move it for better reception RF interference Turn OFF wall switch for 5 seconds then turn back ON Continuing RF interference HUNTER FAN COMPANY CONTROL LIMITED WARRANTY Change dip switch settings to a different code in both Transmitter and Receiver The Hunter Fan Company makes the following limited warranty to the original purchaser of the Control Control Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL THIS WARRANTY AND ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE VOIDED THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO ANY CONTROL IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL This warranty excludes malfunctions or failures which were caused by repairs by persons not authorized by us mishandling improper installation modifications or damage to the Control while in your possession o
4. Hunter Universal Fan amp Light Remote Control Model 27185 Ratings 120 VAC 60 Hz 1 0 Amp Fan 300 Watts incandescent light Receiver Weight 6 oz Read and Save these Instructions Caution Risk of Electrical Shock All wiring must be performed in accordance with national and local electrical codes If you are unfamiliar with the wiring codes you should use a qualified electrician To avoid overheating and possible damage to other equipment do not install to control a receptacle fluorescent light fixture motor operated appliance or transformer supplied appliance Use only to control one paddle blade ceiling fan and incandescent light fixture Notes 1 This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will
5. not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 3 For use only with electrically reversible ceiling fans rated at 1 0 amp or less and fan incandescent light kits rated at 300 watts or less 4 Not for use with shaded pole motors Not recommended for use with the Hunter Original For Hunter Original series fans use Hunter control model numbers 27187 22691 or 27189 5 Medium and Low fan speeds are determined by the control and thus may vary from the factory settings due to normal motor variations 6 For use with Hunter Hanging systems excludes Hunter Original on angled ceilings up to 34 degree pitch ceilings 7 Not for use in applications where the fan does not have a wall switch Any changes or modifications to this equipment not expressly approved by Hunter Fan Company will void the user s authority to operate the equipment Before Installing the Control 1 Use the pull chain switch to set the fan
6. r unreasonable use This warranty does not apply to batteries or to deterioration or damage to the product caused by the use of faulty batteries To obtain a replacement return your Control postage prepaid along with proof of purchase to Hunter Fan Company Service Department at 2500 Frisco Avenue Memphis Tennessee 38114 IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 41316 01 06 18 2008 Printed in China and Taiwan
7. shown in Figure 3 Extend antenna through one of the ceiling plate openings approximately 3 6 Low Profile Style II Fig 2 D Secure receiver to the ceiling mounting bracket with UL listed cable ties not included Connect wiring as shown in Figure 3 Extend antenna above the ceiling mounting bracket approximately 3 6 Bracket Hanger Fig 2 E Starting with the antenna wire slide receiver inside mounting bracket If a ground wire mounting screw prevents the receiver from sliding into the bracket move ground wire and screw to an unused hole at the top of the bracket or secure with a canopy mounting screw The bracket must remain properly grounded Connect wiring as shown in Figure 3 Extend antenna above the receiver approximately 5 8 Cable Tie Routing for Low Profile Fans Figs 2 C 2 D Insert cable tie through open ings as shown DO NOT insert the cable Q tie through the inside of the receiver The cable tie NS can be placed across the length or width of the receiver to best match your fan installation type Nz TROUBLESHOOTING Figure 4 Fan High Fan Medium Fan Low Fan OFF Light Key 1 Light Operation Turn ON wall switch the light will turn ON at maximum brightness Press and quickly release the light key on the hand held remote to turn the light OFF or ON Light will come ON at maximum brightness Press and hold the light button for more than 1 second to turn the light ON and
8. speed to the HIGH position before installa tion Do not use the pull chain to change the fan speed after installation as damage to your ceiling fan or universal control may result The speed of the fan should only be changed by the Hunter control 2 Set the ceiling fan light kit to the ON position before installation The light level should only be changed by the Hunter control Figure 2 Receiver Installation 1 Disconnect power to the ceiling fan and light kit at the main electrical panel Remove fuse or move circuit breaker to the OFF position 2 IMPORTANT Before installing this control check the factory default dip switch set tings Refer to Figure 1 Be sure the dip switch positions of the transmitter and receiver match or the ceiling fan will not function Select different combinations of dip switches to prevent mis operation due to other remote control fans 3 IMPORTANT If your ceiling fan light kit is using incandescent bulbs then slide the CFL INC switch to the INC position If your ceiling fan light kit is using compact fluo rescent light bulbs CFL then slide the CFL INC switch to the CFL position NOTE When the switch is in the CFL position the dimming feature is disabled and you will not be able to dim the light bulbs This feature is to protect both your bulbs and your receiver as CFL bulbs are not able to dim and will malfunction if dimming is attempted 4 Determine your ceiling fan mounting type Figure 2
9. the 9 Volt alkaline battery A23 or equivalent inside the hand held transmitter after setting the dip switches to match the dip switches in the receiver 2 Mount the remote holder over the ceiling fan s wall switch using the existing wall plate screws Refer to Figure 4 3 The transmitter can be placed on the remote holder for convenience or safekeeping Fan Installation Types NOTE Some fans may have considerable excess lead wire For easier canopy installation cut the excess wire leaving a minimum of 6 inches remaining Restrip the fan lead wires 1 2 inch Place remaining excess wire into the ceiling electrical box as needed Canopy Hanger Fig 2 A Place receiver in canopy Connect wiring as shown in Fig ure 3 Extend antenna through one of the ceiling plate openings approximately 3 6 Hands Free Canopy Receiver Placement On Motor Fig 2 C Low Profile Ceiling CoN Plate a Ceiling Bracket Antenna Receiver Motor Fan Mounting Motor Plate Low Profile II Bracket Hanger Wiring Diagram Figure 3 Antenna Black Hot White Neutral Hunter Hands Free Canopy Fig 2 B Connect wiring as shown in Figure 3 Place receiver inside mounting bracket Extend antenna above the ceiling mounting bracket approximately 3 6 Low Profile Style Fig 2 C Secure receiver to the fan plate above the motor with UL listed cable ties not included Connect wiring as
Download Pdf Manuals
Related Search