Eureka C2132A Upright Vacuum
Contents
1. For location of nearest Eureka Warranty Station or service information call 1 800 282 2886 En Mexico llame al 5670 6169 Commercial Upright Vacuum Cleaner WITH EZKLEEN DUST BAG Owner s Guide Index Important Safeguards General Information Assembly EZ Kleen Dust Bag Brush Roll Brush Roll Belt Headlight Warranty www eureka com IMPORTANT SAFEGUARDS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces Do not leave vacuum cleaner when plugged in Turn off the switch and unplug the electrical cord when not in use and before servicing Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If vacuum cleaner is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center before using Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run vacuum cleaner over cord Keep cord away from heated surfaces Connect to a properly grounded outlet only refer to Grounding Instructions Do not u2. bottom plate over tabs of cleaner base 9 Seat and secure cam locks Ask for GENUINE EUREKA replacement belts No 52100 Look for the oY ronal symbol 13 Headlight Bulb Standard on some models NOTE Turn off the switch and unplug the electrical cord before replacing headlight bulb Headlight style varies by model Locate the notches that release the tabs at either 1 top 2 side or 3 bottom of the lens as illustrated Place a screwdriver into one notch twist or pry the screwdriver to release the lens Repeat for the second notch on the opposite side Rotate the bulb socket forward Push bulb in and turn to remove Secure new bulb into socket and rotate bulb socket backward Replace the lens tabs into the top of the bottom of the hood opening Rotate lens to position and press down at each notch until the lens locks into position NOTE Use 25 watt replacement bulb only Ask for GENUINE EUREKA replacement bulb 40009A 14 THE EUREKA COMMERCIAL LIMITED WARRANTY WHAT THIS WARRANTY COVERS Your EUREKA commercial cleaner is warranted to be free from all defects in material and workmanship in normal use FOR A PERIOD OF ONE YEAR The warranty is granted only to the original purchaser of the cleaner The warranty is subject to the following provisions WHAT THIS WARRANTY DOES NOT COVER e Parts of the cleaner that require replacement under normal use such as bumpers bags bristle strips belts
3. utilisation d un appareil lectrique quelques pr cautions l mentaires doivent tre observ es incluant les suivantes LISEZ TOUTES LES INSTRUCTIONS AVANT D UTILISER VOTRE ASPIRATEUR AVERTISSEMENT Pour r duire le risque de feu de choc lectrique ou de blessure Ne pas utiliser l ext rieur ou sur des surfaces mouill es Fermez le commutateur et d branchez l appareil lorsque vous ne l utilisez pas ou avant le nettoyage ou l entretien Ne permettez pas qu il soit utilis comme jouet Une attention particuli re est n ces saire lorsque utilis par ou pr s d un enfant Suivez les recommandations d utilisation de ce manuel Utilisez uniquement les acces soires recommand s par le fabriquant Ne pas utiliser si le cordon ou la fiche sont endommag s Si l aspirateur ne fonctionne pas comme il le devrait s il a t chapp s il est endommag s il a t laiss l ext rieur ou chapp dans l eau retournez le un centre de service avant de utiliser Ne pas le tirer ou le transporter par le cordon ne pas utiliser le cordon en guise de poign e Ne pas fermer une porte sur le cordon ou tirer le cordon sur des coins ou bordures pointus Ne pas circuler sur le cordon avec l aspirateur Tenir le cordon a distance des surfaces chauffantes Branchez toujours l aspirateur dans une prise trois mise la terre Ne pas utiliser des rallonges ou des prises qui n ont pas de capaci
4. CONSERVEZ CES INSTRUCTIONS INSTRUCTIONS VISANT LA MISE LA TERRE Cet appareil doit tre mis la terre En cas d faillance ou de panne ventuelles la mise la terre fournit au courant un chemin de moindre r sistance qui r duit le risque de choc lectrique Cet appareil est pourvu d un cordon muni d un conducteur de terre et d une fiche avec broche de terre La fiche doit tre branch e dans une prise appropri e correctement install e et mise la terre conform ment aux r glements et ordonnances AVERTISSEMENT Un conducteur de terre mal raccord peut entra ner un risque de choc lectrique Consulter un lectricien ou un technicien d entretien qualifi si vous n tes pas certain que la prise est correctement mise la terre Ne pas modifier la fiche fournie avec l appareil si elle ne peut tre ins r e dans la prise faire installer une prise ad quate par un lectricien qualifi NOTE Au Canada l utilisation d un adaptateur temporaire n est pas autoris e par le Code canadien de l lectricit Cet appareil est destin un circuit de 120 V et est muni d une fiche de mise la terre semblable celle illustr e par le Figure A S assurer que l appareil est branch une prise de courant ayant la m me configuration que la fiche Aucun adaptateur ne devrait tre utilis avec cet appareil Bo te de Prise de Terre el 2 LA LAME DE TERRE A FIGURE A EST LA PLUS LONGUE DES TROIS LAM
5. E EUREKA replacement brush strip 12 inch No 52282 16 inch No 52246 1 12 Brush Roll Belt The brush roll belt on the upright vacuum cleaner drives the brush to agitate sweep and comb the carpet nap The belt should be checked regularly to be sure it is in good condition Replace the belt if it is stretching cracking or slipping Cut away any hair or thread wound around the brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly How To Replace A Worn Belt NOTE Turn off the switch and unplug the electrical cord before replacing belt Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt IMPORTANT Improper installation of the brush roll or brush roll belt could cause carpet or cleaner damage 2 Pull up on belt to rotate it off the motor pulley Lift up on brush roll and remove worn belt Check for brush wear see Brush Roll instructions 5 Place rubber end cap covers over 3 Place new belt around brush roll both end caps flat side against end 4 Align brush roll pulley with belt cap Align the holes and secure guide Then slant brush roll forward so end caps are in line with slots in cleaner base 6 Push brush roll into place 7 Place lower side of belt into belt guide and pull to stretch the belt around the left side of motor pulley Rotate pulley to secure belt into groove 8 Place slots of
6. ES GENERAL INFORMATION The cleaner is designed to pick up dirt and dust particles Avoid picking up hard or sharp objects with the cleaner to prevent bag tears hose clogs and fan blade breakage with subsequent motor damage Service Information The instructions in this booklet serve as a guide to routine maintenance For additional service information telephone our toll free number for the nearest Eureka Authorized Warranty Station You should know the model type and serial numbers when you call USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 If you prefer you can write to The Eureka Company Service Division 807 North Main Street Bloomington Illinois 61701 USA In Canada write to The Eureka Company 866 Langs Drive Cambridge Ontario N3H 2N7 DO NOT OIL the motor or the brush roll at any time The bearings are permanently lubricated and sealed Rating Plate The model type and serial numbers are indicated on the rating plate located on the bottom of the cleaner For prompt and complete service information always refer to these numbers when inquiring about service MODEL VOLTS TYPE AMPS SERIAL NO HERTZ SERVICE INFORMATION 1 800 282 2886 THE EUREKA COMPANY BLOOMINGTON ILLINOIS 61701 Model amp Type Serial No ff ie amp HOW TO ASSEMBLE q 9 uf D Se if amp En CAUTION Fully assemble the cleaner S before using A B c D Assembly Packet 2 Part Cord Bellows Cord T
7. e substances it may be necessary to turn off the cleaner and empty the dust cup more often NOTE Turn off the switch and unplug the electrical cord before emptying the dust cup Never operate the vacuum cleaner without the dust cup latched in place 1 Unhook 1 Unhook the clip from the top of the cloth bag 2 Shake the cloth bag to release dust clinging inside 3 Release 3 Release each latch one on either side of the handle push down on the lock lift up on the bottom and pull the top forward NOTE Keep the latch free of dust or obstructions that would prevent it from locking securely 4 Lift the lid swing it up and outward 5 Reach in grasp the dust cup and pull it out of the support 6 Empty contents in a suitable container If desired the cup can be washed in 7 Replace warm water using a mild soap solu Cup tion Be sure the cup is completely ary and before replacing Swing Lid Shut Place the cup into the support swing the lid shut and fasten each latch Hook clip to top of bag refer to item 1 11 Brush Roll As the brush roll rotates it sweeps and combs the carpet nap Remove hair and threads from the brush roll so it continues brushing the carpet nap When the bristles of the brush roll no longer touch a straight edge held across the bottom plate the brush roll is ineffective because the bristles no longer touch the carpet nap To maintain the most effective cleaning u
8. e testing the setting until the cleaner is comfortable to move Moving the knob or slide to the next higher setting raises the brush roll slightly making the cleaner easier to push However the brush roll must make contact with the carpet for effective cleaning Recommended Setting Example of Carpet HOW TO MAINTAIN The instructions given in this booklet serve as a guide to routine maintenance To avoid unnecessary service calls check the bag belt and brush roll often Cleaner Care NOTE Turn off the switch and unplug the electrical cord before cleaning unit To keep the vacuum cleaner looking new it can be wiped with a damp cloth and a mild soap solution then thoroughly dried Never use any type of chemical as chemicals can damage the cleaner When not in use the cleaner should be stored in a clean dry place 10 EZ Kleen Dust Cup and Bag The cloth bag and the dust cup play a very important role in the efficiency of the vacuum cleaner The cloth bag allows air to move through the cleaner while it traps dirt inside the cloth bag and the dust cup When dirt particles cling to the cloth bag they can restrict airflow If air cannot pass through the cloth bag no cleaning can take place regardless of how powerful the unit Some fine particles can restrict airflow very quickly and will decrease performance even before the dust cup appears to be full For that reason when vacuuming powder flour dust or similar fin
9. he assembly packet contains two 2 part pr Hooks screws ane handle bolts 2 cord hooks 2 bellows os San screws and 1 cord clamp with a screw An extra belt is included with some models Secure Bellows Check to be sure the end of the bellows is secure in the chrome bellows adapter Align the screw holes in the bellows adapter with the back of the base start the screws C by hand and tighten 6 Attach Lower Handle Raise the dust cup support Push the lower handle largest end down through the tube of the dust cup support and into the handle socket at the back of the cleaner Make sure the notches on the lower handle face the rear of the cleaner Fig 1 Align the holes insert a 2 part bolt A and tighten Dust Cup Lower Support Handle Assemble Upper Handle Hold the upper handle so it curves away from the cleaner Then push it down over the lower handle Secure with the other 2 part handle bolt A Secure Cord Clamp Secure the electrical cord to the dust cup support with the cord clamp and screw D Place the cord clamp over the electrical cord Screw the clamp to the tab below the left latch start the screw by hand then tighten Toward Rear of Cleaner Handle Socket Upper Handle Lower Handle Handle Socket Attach Lower Cord Hook Insert the power cord into the lower cord hook A as shown Snap the hook into the lower handle Pull up on the cord to tighte
10. light bulbs hoses fans and impellers e Damages or malfunctions caused by negligence abuse or use not in accordance with the Owner s Guide e Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts WHAT THE EUREKA COMPANY WILL DO The Eureka Company will at its option repair or replace a defective cleaner or cleaner part that is covered by this warranty As a matter of warranty policy the Eureka Company will not refund the consumer s purchase price WARRANTY REGISTRATION Please fill out and return the warranty registration card accompanying your cleaner continued on reverse side 15 OBTAINING WARRANTY SERVICE To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station You will find the nearest location in the Yellow Pages under Vacuum Cleaners Service and Repair Be certain that the Warranty Station is Eureka Authorized For the location of the nearest Eureka Authorized Warranty Station or for service information telephone toll free USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 If you prefer you can write to In Canada write to The Eureka Company The Eureka Company Service Division 866 Langs Drive 807 North Main Street Cambridge Ontario N3H 2N7 Bloomington IL 61701 If it is necessary to ship the cleaner outside your community to obtai
11. n but leave enough slack near the base so the cord is not strained when the handle is lowered Attach Upper Cord Hook Pull the spring on the electrical cord upward toward the top of the handle Make sure slots in handle are positioned properly see Detail B Insert the lower half of the spring into the upper cord hook as shown Snap the hook into the upper handle directions below BAG SUPPORT HOOK 1 Place 3 inner tab around inner tab into into slot handle place Cord Storage Wrap the cord around the two cord hooks Fasten the plug to the cord to prevent unwinding Hook Bag Top Slip the ring at the top of the cloth bag over the bag support hook on the back of the cord hook BAG SUPPORT HOOK HOW TO USE The upright vacuum cleaner is designed to be used on multiple types of carpeting Do not attempt to use the upright vacuum cleaner on bare floors as damage to the floor covering may result Above the floor cleaning tools are available optional Handle Adjustment With the tip of the foot press down to release the handle lock located at the left rear side of the cleaner Move the handle and adjust it to the desired position for 1 storing upright 2 operating the cleaner at a comfortable height for the user and 3 cleaning under neath low furniture f 1 Store 3 Clean Underneath Handle Lock Power Switch The power switch is mounted on the motor hood near the handle Switch style va
12. n warranty repair you must pay the shipping charges to the Eureka Authorized Warranty Station Return shipping charges will be paid by the Warranty Station When returning parts for repair please include the model type and serial numbers from the data plate on the cleaner FURTHER LIMITATIONS AND EXCLUSIONS Any warranty that may be implied in connection with your purchase or use of the cleaner including any warranty of MERCHANTABILITY or any warranty for FITNESS FOR A PARTICULAR PURPOSE is limited to the duration of this warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you Your relief for the breach of this warranty is limited to the relief expressly provided above IN NO EVENT SHALL EUREKA BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES THAT YOU MAY INCUR IN CONNECTION WITH YOUR PURCHASE OR USE OF THE CLEANER Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights You may also have other rights which vary by State THE EUREKA COMPANY Bloomington Illinois 61701 57801C 2002 White Consolidated Ltd Part No 72660 11 02 Printed in U S A
13. nto an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DANGER Improper connection of an equipment grounding conductor can result in risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the appliance If it will not fit the outlet have proper outlet installed by a qualified technician This appliance is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in Figure A A temporary adapter which looks like the adapter illustrated in Figure B may be used to connect this plug to a two pole receptacle as shown if a properly grounded outlet is not available The temporary adapter should be used only until a properly grounded outlet Figure A can be installed by a qualified electrician The green colored rigid ear lug or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adapter is used it must be held in place by a metal screw NOTE In Canada the use of a temporary adapter is not permitted by the Canadian Electrical Code GROUNDED GROUNDED OUTLET BOX OUTLET BOX a ADAPTER k ae a GROUNDING BLADE FIGUREA IS LONGEST OF THE METAL THREE BLADES SCREW FIGURE B GROUNDING TAB CONSEILS DE S CURIT Lors de l
14. ries by model and may differ from the illustration A push with the foot turns the motor ON push again to turn the motor OFF Cleaner Height Setting WARNING Avoid injury Keep loose clothing hair fingers and all other parts of body away from any moving part such as the revolving brush Turn off the switch and unplug the cleaner before changing the cleaner height setting Adjust the vacuum cleaner height setting to match the carpet pile height Refer to the following chart of recommended settings for carpet types The front of the cleaner has either a knob or slide adjustment which raises or lowers the cleaner base to match the type of carpet With the cleaner cord Position 1_ommmm Low pile as kitchen indoor unplugged set the adjustment according outdoor to the table as a starting point While Pr the cleaner is off and disconnected Porters akilli Sc lpttirgd from the outlet place the handle inthe Position 3 MMW Plush or thick sculptured operating position tilt the cleaner back to remove the weight from the wheels Position 4 WW Thick plush and adjust me setting Then plug ine If the cleaner has additional height settings th for thick cleaner into the electrical outlet turnon carpets or where easier pushing is desired o o oer the switch lower the handle and pass the cleaner over the carpet If the cleaner is still difficult to push follow the procedure and test the cleaner at the next higher setting Continu
15. se a new wood brush roll Replace the brush strips on the chromed steel brush roll How To Replace Worn Brush Strips chromed steel brush roll NOTE Turn off the switch and unplug the electrical cord before replacing brush strips New brush strips are supplied in sets of two one long and one short To replace remove bottom plate and belt see How To Change Belt Then grasp center of brush roll and lift to remove OW mn MO Remove rubber end cap cover from one end Unscrew locknut Remove end cap S eeve bearing brush roll assembly includes a shatt washer not pictured Remove bearing retainer Push shaft through opposite end Pull out worn brush strip with pliers Slide in new brush strip of same length rounded end first Fit track on either side into brush roll slot Replace second brush strip from opposite end of brush roll Replace shaft Align indentation on bearing retainer with brush strip on both ends of brush roll Replace shaft washer on sleeve bearing assembly Position end cap with flat sides of center hole over flat sides of threaded shaft Tighten locknut Align holes and secure rubber end cap cover flat side against end cap When properly assembled the brush roll should rotate freely between the two end caps Check the condition of the belt change if necessary Replace the brush roll belt and bottom plate see How To Replace A Worn Belt Ask for GENUIN
16. se extension cords or outlets with inadequate current carrying capacity Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or vacuum cleaner with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce airflow This vacuum cleaner creates suction and contains a revolving brush roll Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dust bag in place Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Store your cleaner indoors in a cool dry area Keep your work area well lighted Unplug electrical appliances before vacuuming them SAVE THESE INSTRUCTIONS Grounding Instructions This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged i
17. t suffisante pour transporter le courant Fermer tous les contr les avant d brancher Ne pas d brancher en tirant sur le cordon Pour d brancher tenez la fiche et non le cordon Ne pas manipuler la fiche ou l aspirateur avec les mains mouill es Ne pas rien ins rer dans les ouvertures Ne pas utiliser si des ouvertures sont blo qu es assurez vous qu elles soient d gag es de poussi re mousse cheveux ou toute autre chose qui pourrait r duire le passage de lair Cet aspirateur cr e de la succion et contient un rouleau brosse tournant Tenir les parties mobiles et les ouvertures loin des cheveux du linge des doigts et de toute partie du corps Ne pas ramasser des objets qui br lent ou fument comme les cigarettes allumettes ou cendres chaudes N utilisez pas sans le sac de poussi re en place Les poulies du courroie peuvent devenir chaudes pendant l utilisation normale Pour pr venir des br lures vitez de touch la poulie du courroie lorsque vous r parez la courroie Portez une attention particuli re lorsque vous nettoyez les escaliers Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l essence Ne pas utiliser dans les endroits o ces liquides pourraient tre pr sents Entreposez votre aspirateur l int rieur dans un endroit propre et sec Maintenez un bon clairage l endroit o vous travaillez D brancher les appareils lectrique avant de les balayer
Download Pdf Manuals
Related Search