Broan-NuTone N-9960 Combination Heater Heater
Contents
1. u Heat Light Combination with Night Light MODEL 9960 FOR BEST RESULTS In a new construction site install the housing complete with heater during rough in construction of the building The light assembly and the grille should be installed when the finished ceiling is in place Installation in an existing finished building requires an accessible area attic or crawl space above the planned location See INSTALLATION IN EXISTING CONSTRUCTION Do not install closer than 12 inches to a vertical surface Do not install over tub or shower enclosure UNIT DIMENSIONS Refer to Figure 1 for housing s dimensions NOTE If there will be a finished second floor above the Model 9960 housing requires a minimum of 2 x 8 joist construction for mounting WIRING AND DUCTWORK 1 Run the required wiring during rough in stage of construction 2 Total connected load 1680 watts 3 Plan to run 120vAC 60 Hz wiring with ground ona separate 20 Amp circuit from a power source through the provided wall switch to the housing s junction box See wiring diagram INSTALLATION IN NEW CONSTRUCTION PREPARATION 1 Loosen hanger bar brackets to allow bars to be inserted 2 Refer to Figure 2 Insert hanger bars into brackets 3 Refer to Figure 3 Slide hanger bar brackets down to end of slot closest to outside edge of housing Tighten brackets in this position 4 Refer to Figure 4 Remove junction box cover by2. removing one screw 5 Refer to Figure 4 Remove appropriate wiring knockout s and install approved box connector s INSTALLATION INSTRUCTIONS READ amp SAVE THESE INSTRUCTIONS FIGURE 1 HANGER BARS FIGURE 2 ADJUSTMENT SLOT oan KNOCKOUTS MOUNTING THE HOUSING 1 Locate housing between joists 2 Refer to Figure 5 Using nails secure hanger bars to joist NOTE The hanger bar brackets are adjustable Allowing for the thickness of the finished ceiling mount hanger bars so that edge of housing will be flush with the finished ceiling 3 Adjust brackets as required Tighten brackets INSTALLING THE SWITCH 1 Install double gang switch box in chosen location 2 Refer to Figure 6 Run wiring and make wiring connections 3 Use supplied screws to secure switch bracket assembly to switch box 4 Using supplied screws secure wall plate to switch bracket INSTALLING AND CONNECTING THE WIRING Refer to Figure 6 All wiring must comply with local codes and unit must be properly grounded 1 Using 12 gauge wire run 120vAC 60 Hz wiring with ground from a power source to the wall switch location The unit must be wired on a separate 20 Amp circuit 2 Run wiring from switch location to housing as shown in the wiring diagram 3 Make wiring connections as shown in wiring diagram 4 Replace junction box cover Slide slotted hole in cover over screw Tighten screw securely 5 Secure wire cove
3. el No and Product Description IF YOU NEED ASSISTANCE OR SERVICE For the location of your nearest NuTone Independent Authorized Service Center Residents of the contiguous United States Dial Free 1 800 543 8687 Please be prepared to provide Product model number Date and Proof of purchase The nature of the difficulty Residents of Alaska or Hawaii should write to NuTone Inc Attn Department of National Field Service 4820 Red Bank Road Cincinnati Ohio 45227 1599 Residents of Canada should write to Broan NuTone Canada 1140 Tristar Drive Mississauga Ontario Canada L5T 1H9 Rev 03 2001 Product specifications subject to change without notice Printed in U S A Rev 5 2001 Part No 89350
4. ousing must be mounted between ceiling joists 2 Refer to Figure 10 Mark ceiling for cutout Cutout dimensions 14 long x 9 wide Make cutout in ceiling 3 Follow steps under PREPARATION page 1 4 From above lower housing into the cutout and secure hanger brackets Run wiring through box connectors 5 From below adjust housing so that it is flush with the finished ceiling Replace junction box cover Insert heater light and night light plugs into proper receptacles 9 Install grille reflector and lens ONO HEATER Form below make wiring connections as shown in figure 6 LENS DETACHED IN DRAWING FOR ILLUSTRATIVE PURPOSES FIGURE 10 u One Year Limited Warranty WARRANTY OWNER NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one 1 year from the date of original purchase THERE ARE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE During this one year period NuTone will at its option repair or replace without charge any product or part which is found to be defective under normal use and service THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES FILTERS DUCT ROOF CAPS WALL CAPS AND OTHER ACCESSORIES FOR DUCTING This warranty does not cover a no
5. r with one screw 6 Insert heater and ventilator plugs into proper receptacles as shown MOUNTING THE GRILLE ASSEMBLY 1 Refer to Figure 7 Place the reflector into the grille 2 Refer to Figure 8 Insert light plug and night light plug into receptacles 3 Refer to Figure 7 Using two provided screws secure grille and reflector to housing 4 Install 100 watt maximum light bulb into light socket 5 Install 7 watt maximum C 7 candelabra type bulb into night light socket 6 Refer to Figure 9 Snap lens into place HEATER JUNCTION BOX HEATER WHITE LIGHT RED WHT WHT BLK H H NIGHT LIGHT NOTE WHEN THERMOSTAT OR TIMER IS USED CONNECT AT FIGURE 6 GRILLE LENS OMITTED FROM DRAWING FOR ILLUSTRATIVE PURPOSES INSTALLATION IN EXISTING CONSTRUCTION In an existing finished building installation of the Heat Light Combination requires an accessible area attic or crawl space above the planned location If the location that has been chosen for installation has a finished floor above it be certain there is sufficient space available to install the housing PLANNING Review INSTALLATION IN NEW CONSTRUCTION and follow all instructions that apply CAUTION Check the area above the planned location to make sure that 1 Wiring can be run to the planned location 2 No wiring or other obstructions might interfere with the installation INSTALLATION 1 The h
6. rmal maintenance and service or b any products or parts which have been subject to misuse negligence accident improper maintenance or repair other than by NuTone faulty installation or installation contrary to recommended installation instructions The duration of any implied warranty is limited to the one year period as specified for the express warranty Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you NUTONE S OBLIGATION TO REPAIR OR REPLACE AT NUTONE S OPTION SHALL BE THE PURCHASER S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties WARRANTY SERVICE To qualify for warranty service you must a notify NuTone at the address stated below or telephone 1 800 543 8687 b give the model number and part identification and c describe the nature of any defect in the product or part At the time of requesting warranty service you must present evidence of the original purchase date Date of Installation Builder or Installer Mod
Download Pdf Manuals
Related Search