Vtech VT 1711 Cordless Phone
Contents
1. VT 1711 900MHZ DIGITAL SPREAD SPECTRUM CORDLESS TELEPHONE VTECH VTECH COMMUNICATIONS LTD 91 5033 13 00 Made in China This equipment complies with Parts 15 and 68 of the Federal Communications Commission FCC rules for the United States It also complies with regulations RSS 210 and CS 03 of Industry Canada IC A label is located on the underside of the base unit containing both the FCC registration number and Ringer Equivalence Number REN or the IC registration number and Load Number You must upon request provide this information to your local telephone company This equipment is compatible with inductively coupled hearing aids FCC PART 15 Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment The equipment has been tested and found to comply with part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by t2. Never install telephone wiring during a lightning storm 2 Never install telephone jacks in wet lo cations unless the jack is specifically de signed for wet locations 3 Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface 4 Use caution when installing or modifying telephone lines REPLACING THE HANDSET BATTERY PACK IT S IMPOSSIBLE TO OVERCHARGE THE BATTERY PACK The battery pack can be recharged many times but if you get a low battery signal even after 8 hours of maintenance charging in the base cradle or 24 hours in the base spare battery charger the battery pack s should be replaced To purchase replacement battery packs call VTECH Communications at 1 800 595 9511 In Canada call VTECH Electronics at 1 800 267 7377 REPLACING THE HANDSET BATTERY PACK Follow the steps below 1 Remove the battery case cover by pressing on the ridged lines and sliding downward 2 Discard the old battery pack Don t put the old battery pack in a trash compactor or a fire it could burst 3 Place the new battery pack in the battery compartment with the metal contacts facing down 4 Replace the battery case cover by sliding the cover upwards 5 If the new battery pack is not already charged place the handset in the cradle of the base unitto allow itto charge for 16 hours CAUTION To Reduce the Risk of Fire or Injury to
3. of fire or electric shock Never spill liq uid of any kind on the product IMPORTANT SAFETY INSTRUCTIONS 11 To reduce the risk of electric shock do not disassemble this product Opening or removing covers may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the appliance is subsequently used 12 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord plug is damaged or frayed b If liquid has been spilled into the product c Ifthe product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation If the product has been dropped or the cabinet has been damaged f If the product exhibits a distinct change in performance 13 Do not use the telephone to report a gas leak in the vicinity of the leak L SAVE THESE INSTRUCTIONS REPLACING THE HANDSET BATTERY PACK Charging the handset batteries The handset of your VTech VT 1711 cordless telephone is powered by a rechargeable battery pack It charges automatically when ever the handset is in the base You
4. and is treated as a stored digit If your phone is connected to a PBX you can store the PBX access number and a pause before the phone number For example to store 9 PAUSE 555 1234 in memory location 08 do the following The handset must be OFF Press MEM PROG Press 9 Press PAUSE REDIAL to insert a two second pause Dial 5551234 Press MEM PROG Press 08 memory location If programmed correctly the phone will emit two short beeps and exit programming mode ADDITIONAL OPERATING TIPS If the handset is moved to a point where the base unit and handset can no longer communicate the handset will beep twice and the LOW BATT LED will flash slowly to SPARE BATTERY f INDICATOR CHARGING INDICATOR HANDSET IN USE INDICATOR DIALING KEYS POWER lt INDICATOR PAGE KEY Your VT 1711 cordless telephone is equipped with a 2 5mm Headset Jack for use with an optional accessory Headset for hands free operation If you choose to use the Headset option you must obtain an optional accessory Headset which is compatible with the VT 1711 To purchase a Headset call VTech Customer Service at 1 800 595 9511 Once you have a compatible 2 5mm Headset locate the Headset Jack on the VT 1711 Handset Connect the plug on the Headset cord to the jack on the cordless Handset The plug should fit securely Do not force the connection OPERATION NOTE Whenever a com
5. may connect to your telephone line and still enable the devices to ring when you receive a call The general rule is that the REN value should not exceed 5 0 total however contact your local telephone company for the specific number in your area INDUSTRY CANADA IC NOTICE NOTICE The Industry Canada IC label identifies certified equipment This certifi cation means that the equipment meets tel ecommunications network protective op erational and safety requirements as pre scribed in the appropriate Terminal Equipment Technical Requirements document s The department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local tel ecommunications company The equipment must also be installed using an acceptable Parts Check List 1 Base unit Handset and AC adaptor 2 One Line Telephone Cord INTRODUCTION 3 Battery Pack 4 Wall mount accessory 5 Belt Clip To purchase replacement battery packs call VTECH Communications at 1 800 595 9511 In Canada call VTECH Electronics at 1 800 267 7377 Handset Belt Clip gt Battery Pack method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative
6. not use liquid clean ers or aerosol cleaners Use a dry cloth for cleaning 4 Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool 5 Do not place this product on an unstable cart stand or table The telephone may fall causing serious damage to the tel ephone 6 Slots and openings in the cabinet and the back or bottom are provided for ven tilation to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the product on the bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation unless proper ventila tion is provided 7 This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your dealer or local Power Com pany 8 Do not allow anything to rest on the power cord Do not locate this product where the cord will be abused by persons walking on it 9 Do not overload wall outlets and exten sion cords as this can result in the risk of fire or electric shock 10 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk
7. remote access to answering machines bank by phone services use of calling cards and other special services 1 Dial the call normally 2 Then activate the Temporary Tone feature by pressing TONE key 3 You can then press the numbers or sym bols you need and your phone will send the proper tones To end the call press ON OFF or place the handset back in the base The phone will auto matically go back to rotary dial pulse service PROGRAMMING THE RINGER The handset ringer is capable of four different types of ringing tones The following section details how to select different ringer types CHANGING RINGER TYPES To program the handset must be OFF To select a different ringer type do the following slowly Plug the base in again and this will stop NOISE OR INTERFERENCE Your VTech VT1711 cordless telephone has auto channel scan circuitry which will detect excess noise and change the channel of the phone to reduce it This is done automatically Since the VTech VT1711 is a fully digital phone it does not suffer from noise associated with regular cordless phones At times you may experience occasional drop outs especially at the extreme edges of the phone s range Simply move closer to the base unit and this will disappear The RBRC Seal on the easily removable nickel cadmium battery contained in our product indicates that VTech Communications INC is voluntarily participating in an ind
8. the call signal Out of Range OUT OF RANGE WHEN PHONE IS ON If you are presently engaged in a phone conversation move closer to the base If the base unit does not communicate with the handset within 25 seconds of losing contact it will automatically hang up OUT OF RANGE WHEN PHONE IS OFF If the phone is OFF the handset and base still monitor each other to make sure that they can communicate If the handset is moved out of range the handset will beep twice and then the LOW BATT LED will flash slowly The handset will re link with the base automatically once it is brought back within range The unit will then be able to receive and place calls When the base unit is unplugged from the power supply the handset will beep twice and the LOW BATT LED will flash The RBRC Seal Canada BASIC OPERATION BASIC OPERATION If a call is on Hold using VT1711 and the user picks up another phone on the same link the VT1711 will take itself off hold and turn off therefore you do not have to go back to turn the phone off if you go to another extension It is done automatically PAGE To page from the base press PAGE To cancel the page either press PAGE again on the base or press ON OFF on the handset ADVANCED FUNCTIONS TEMPORARY TONE If you have rotary dial pulse telephone service TONE PULSE switch is set to PULSE this feature allows you to temporarily switch to TONE dialing for such purposes as
9. 2 months from current date Units purchased in AS IS condition or units purchased as Distressed Merchandise HOW DOES STATE LAW RELATE TO THIS WARRANTY This warranty gives you specific rights You may also have other rights that vary from state to state If you have difficulty operating your phone the suggestions below should solve the problem If you still have difficulty after trying these suggestions call VTECH Communications at 1 800 595 9511 In Canada call VTECH Electronics at 604 273 5131 THE PHONE DOESN T WORK AT ALL Make sure the power cord is plugged in Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall jack Make sure the batteries are properly charged If the LOW BATT LED is flashing the battery pack needs charging NO DIAL TONE First check all the suggestions above If you still don t hear a dial tone disconnect the base unit from the telephone jack and connect a different phone If there is no dial tone on that phone either the problem is in your wiring or local service Call your local telephone company YOU GET NOISE STATIC OR A WEAK SIGNAL EVEN WHEN YOU RE NEAR THE BASE UNIT Household appliances plugged into the same circuit as the base unit can some times cause interference Try moving the appliance or the base unit to another outlet YOU GET NOISE STATIC OR A WEAK SIGNAL WHEN YOU RE AWAY FROM THE BASE
10. Handset is returned to the Base Unit cradle You may return the Handset to its cradle whenever you re not using the phone SPARE BATTERY CHARGER The VT 1711 has a built in Spare Battery Charger which is located in the cradle of the Base Unit NOTE In order to benefit from this feature you must obtain an optional Spare Battery pack from an authorized VTech dealer or by contacting VTech Customer Service at 1 800 595 9511 INSTALLATION Remove the Spare Battery charger cover by pressing the release tab and lifting up Place a battery pack in the Spare Battery charger Make sure the metal charging contacts on the underside of the battery pack are aligned with the charging contact in the Spare Battery charger POWER BACKUP When a Spare Battery pack is installed in the Base Unit the VTech 1711 uses this battery to provide operational backup in case of a power failure If you have a fully charged battery pack in the Spare Battery charger and there is a power outage you will still be able to place and receive calls for up to four hours 2 Mount the base on the wall Position the base so the mounting studs will fit into the holes on the bottom of the base Position the power cord to extend down the wall the phone is to be mounted on Slide the base down on the mounting studs until it locks into place 3 Connect the telephone line cord The telephone line cord has a snap in plug at each end Insert one of the plug
11. Persons read and Follow the Instructions 1 Use only VTECH rechargeable battery pack 2 Do not dispose of the battery in a fire The cell may explode IMPORTANT Do not dispose of this battery into household garbage For information on recycling or proper disposal consult your local solid waste collection or disposal organization The Wall Mount adaptor is designed to fit on standard Wall Mount plates 1 Choose a spot near an electrical outlet and a telephone jack Your phone requires a modular telephone jack and a standard electrical outlet 120v AC The power cord is six feet long make sure there is an electrical outlet within reach of the base The outlet should not be con trolled by a wall switch If the switch is ever turned off the phone will not operate USING THE WALL MOUNT ADAPTOR 1 Position the wall mount bracket on the base Line up the tabs on the wall mount adaptor with the holes on the bottom of the base Snap the wall mount bracket firmly in place WALL MOUNTING 3 Do not open or mutilate the battery Released electrolyte is corrosive and may cause damage to the eyes or skin It may be toxic if swallowed 4 Exercise care in handling batteries in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause burns A WORD ABOUT RECHARGEABLE BATTERIES Your Ni Cd battery pack recharges whenever the
12. UNIT You may be out of range Either move close to the base or relocate the base unit The layout of your home may be limiting the range Try moving the base unit to another position TAKING CARE OF YOUR TELEPHONE Your VTech VT 1711 cordless telephone contains sophisticated electronic parts so it must be treated with care AVOID ROUGH TREATMENT PLACE THE HANDSET DOWN GENTLY SAVE THE ORIGINAL PACKING MATERIALS TO PROTECT YOUR TELEPHONE IF YOU EVER NEED TO SHIP IT AVOID WATER Your telephone can be damaged if it gets wet Do not use the handset outdoors in the rain or handle it with wet hands Do not install your base unit near a sink bathtub or shower Direct Sequence Spread Spectrum Cord less Telephone FREQUENCY CONTROL Crystal Controlled PLL Synthesizer TRANSMIT FREQUENCY 902MHz to 928MHz NOMINAL EFFECTIVE RANGE MAXIMUM POWER ALLOWED BY FCC AND IC ACTUAL OPERATING RANGE MAY VARY ACCORDING TO ENVIRONMENTAL CONDITIONS AT THE TIME OF USE IN CASE OF DIFFICULTY MAINTENANCE THE HANDSET DOES NOT RING WHEN YOU RECEIVE A CALL Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack Make sure the power cord is plugged in You may be too far from the base unit You may have too many extension phones on your telephone line to allow all of them to ring Try unplugging some of the other phones YOU HEAR OTHER CALLS WHILE USING YOUR PHONE Di
13. designated by the supplier Any repairs or alterations made by a user to this equipment or equip ment malfunctions may give the telephone communications company cause to request the user to disconnect the equipment User should ensure for their own protec tion that the electrical ground connections of the power utility telephone lines and in ternal metallic water pipe system if present are connected together This precaution FCC AND IC REGULATIONS may be particularly important in rural areas Caution User should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate NOTICE The Ringer Equivalence Number REN assigned to each terminal de vice provides an indication of the maxi mum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 0000 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read and understand all instructions 2 Follow all warnings and instructions marked on the product 3 Unplug this product from the wall outlet before cleaning Do
14. l characters Press MEM PROG once more Enter the two digit memory location you wish to store the number in 01 20 If programmed correctly the phone will emit two short beeps and exit programming mode MEMORY SPEED DIALING Press ON OFF to get dial tone Press MEM PROG Enter a 2 digit location number 01 20 The number stored in that location will be automatically dialed CHANGING STORED NUMBERS To change or replace a stored number simply store a new number in the desired memory location DELETING STORED NUMBERS To delete a stored number from memory do the following LOW BATTERY INDICATOR PHONE INDICATOR FLASH KEY BASIC OPERATION BASIC OPERATION VOLUME UP amp DOWN ON OFF KEY TONE Temporary tone MEM KEY REDIAL KEY HOLD KEY The handset must be OFF Press MEM PROG to enter program mode Press MEM PROG again Enter the two digit memory location that you wish to delete 01 20 The phone will emit two short beeps and exit programming mode NOTE Stored numbers are retained in memory even if the base loses its power or the handset battery is removed STORING SPECIAL CODES To insert a pause in a phone number press PAUSE REDIAL at the appropriate point when entering the number This inserts a2 second pause For longer pauses press PAUSE REDIAL two or more times Each press makes the pause 2 seconds longer
15. not covered by warranty as deter mined by VTECH Communications Ship the unit via UPS Insured or equiva lent to VTECH COMMUNICATIONS 11035 SW 11th STREET BLDG B SUITE 270 BEAVERTON OR 97005 HEADSET OPERATION 12 WARRANTY 14 The headband can be adjusted to fit the contour of your head Using both hands slide the headband up or down so that it rests comfortably on your head with the speaker cushion centered against your ear For maximum sound quality the flexible microphone should be positioned at the corner of your mouth about one inch from your face BELT CLIP The VT 1711 is also equipped with a detachable belt clip Align the pins on the inside edge of the clip with the notches on the sides of the VT 1711 Handset The belt clip should snap securely into place Do not force the connection In Canada VTECH ELECTRONICS SUITE 2007671 Alderbridge Way Richmord B C U6X 1Z9 VTECH Communications assumes no responsibility for units sent without prior Return Authorization WHAT DOES OUR WARRANTY NOT COVER Batteries Damage from misuse neglect or acts of nature lightning floods power surges etc Products which may have been modi fied or incorporated into other products Products purchased and or operated outside the USA its territories or Canada Products serviced by the owner or a service facility not expressly authorized by VTECH Communications Products purchased more than 1
16. patible Headset is connected to the cordless Handset the microphone on the Handset will be muted This is done to limit the effect of background noise The following operational characteristics apply to VTech Headsets The same may also apply to other non VTech supplied headsets but VTech assumes no responsibility for their performance The VTech brand compatible Headset has a reversible monaural design You can wear your Headset on either ear leaving one ear free for room conversation WARRANTY STATEMENT WHAT DOES OUR WARRANTY COVER Any defect in material or workmanship FOR HOW LONG AFTER THE ORIGINAL PURCHASE To the original purchaser only ONE YEAR WHAT WILL VTECH DO At our option repair or replace your unit HOW DO I SEND MY UNIT IN OR OUT OF WARRANTY in the U S call VTECH COMMUNICATIONS CUSTOMRER SERVICE For Return Authorigation at 1 800 595 9511 In Canada call VTECH ELECTRONICS at 1 800 267 7377 Properly pack your unit Include any ca bles and accessories that were origi nally provided with the product We rec ommend using the original carton and packing materials Include in the package a copy of the sales receipt or other evidence of date or original purchase if the unit was purchased within the last twelve months Print your name and address along with a description of the defect and include this in the package Include payment for any service or re pair
17. s into the jack on the bottom of the base Insert the other end of the plug into the wall jack 4 Plug the AC adaptor into an electrical outlet and the DC connector on the back of the Base Unit ANSWERING CALLS When the Handset is in the Base Unit cradle simply pick up the Handset to answer an incoming call When the Handset is away from the Base Unit press any key to answer an incoming call MAKING CALLS 1 Press the ON OFF key and wait for a dial tone 2 Then dial the number you want If you make a mistake when dialing press ON OFF to hang up then press the ON OFF key to get the dial tone again DISCONNECTING To end a call either place the handset back in the Base Unit or press ON OFF VOLUME CONTROLS The volume controls for the handset are located on the side of the unit Press the 4 or Y key to increase or decrease the volume While on an active call holding either key down will continually change the volume setting The earpiece volume level will change accordingly There are four volume levels FLASH You can use your VTech VT1711 cordless phone with services such as Call Waiting Simply press the FLASH key REDIAL To REDIAL the last number you dialed press the ON OFF key then press REDIAL The phone will automatically dial the number HOLD Press HOLD to place an active call on hold The PHONE LED will flash to indicate call is on hold Press ON OFF or HOLD again to return to
18. sconnect your base unit from the telephone jack and plug in a regular telephone If you still hear other calls the problem is probably in your wiring or local service Call your local telephone company YOU HEAR NOISE IN THE HANDSET AND NONE OF THE KEYS OR BUTTONS WORK Make sure the power cord is plugged in Your base unit and handset may not be operating on the same channel or security code Place the handset in the cradle for a few moments to reset the channel COMMON CURE FOR ELECTRIC EQUIPMENT Electronics like people can sometimes get confused If the unit does not seem to be responding normally then try putting the handset in the cradle If it does not seem to respond after trying this a few times do the following in the order listed 1 Disconnect the power to the base Disconnect the handset battery Wait a few minutes Connect power to the base Connect the handset battery oan op Put the handset in the base 13 ELECTRICAL STORMS Electrical storms can sometimes cause power surges harmful to electronic equipment For your own safety use caution when using electric appliances during storms CLEANING YOUR TELEPHONE Your telephone has a durable plastic casing that should retain its luster for many years Clean it only with a soft cloth slightly dampened with water or a mild soap Do not use excess water or cleaning solvents of any kind ReMEM PROGber that electrical appliances can cau
19. se serious injury if used when you are wet or standing in water DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL Then pull the unit out by the unplugged cords TECHNICAL SPECIFICATIONS SIZE Handset 186 5 L X64 W X45 D mm Base 205 L X156 W X57 H mm WEIGHT Handset 280g Base 415g POWER REQUIREMENTS Handset Self contained nickel cadmium rechargeable battery supply 3 6V nominal 600mAh capacity Base 9VDC 500mA MEMORY Memory Dial 20 Memory locations 15 16 Digits per location
20. should charge the battery pack for 16 hours when you first receive your phone You ll know that battery pack needs charging when The phone emits a warning tone when you press the ON OFF key The LOW BATT LED is slowly flashing The handset seems completely dead no lights are evident and pressing keys do not generate a beep To Charge the Battery Pack To charge the battery pack place the handset in the base unit The CHARGE indicator will light to show the handset is seated properly and the battery pack is charging It is recommended that the battery pack be charged for at least 16 hours initially and 8 hours for maintenance charging You can use your telephone before that with diminished capacity but it is best to charge the battery pack fully It will take several recharge cycles to maximize the charge capacity of your battery pack The maximum battery life between charges is 7 hours of continuous talk time or 14 days of stand by Alternatively if you have purchased a spare battery pack and it has been charging in the base unit simply exchange the drained handset battery pack with the fully charged replacement battery pack from the base charger Place the drained handset battery pack into the base charger to recharge REPLACING THE HANDSET BATTERY PACK REPLACING A DRAINED HANDSET BATTERY The spare battery pack can also be used to replace a drained Handset battery pack to ensure interrupted use Be sure to p
21. urning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorientate or relocate the receiving an tenna Increase the separation between the equipment and receiver Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected Consult the dealer or an experienced ra dio TV technician for help FCC AND IC REGULATIONS BEFORE USING YOUR NEW PHONE WE STRONGLY RECOMMEND YOU READ THIS MANUAL THOROUGHLY FCC PART 68 The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack USOC RJ11C or RJ11W Your telephone company may discontinue your service if your equipment causes harm to the telephone network They will notify you in advance of disconnection if possible During notification you will be informed of your right to file a complaint with the FCC If it is determined that your telephone equipment is malfunctioning the FCC requires that it not be used and that it be unplugged from the modular jack until the problem has been corrected Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents or by others who may be authorized by the FCC For repair procedures follow the instructions outlined under the VTECH Limited Warranty The REN is useful in determining the number of devices you
22. ustry program to collect and recycle these batteries at the end of their useful lives when taken out of service within the United States and The RBRC program provides a convenient alternative to placing used nickel cadmium batteries into the trash or municipal waste which may be illegal in your areas VTech s participation in RBRC makes it easy for you to drop off the spent battery at local retailers participating in the RBRC program or at authorized VTech product service centers Please call 1 800 8 BATTERY for information on Ni Cd battery recycling and disposal bans restrictions in your area VTech s involvement in this program is part of its commitment to protecting our environment and conserving natural resources Remove the nickel cadmium battery pack by pressing on the lock knob and sliding downward as mentioned on this manual RBRC is a registered trademark of Rechargeable Battery Recycling Corporation Press FLASH Press 1 for ringer type 1 2 for ringer type 2 3 for ringer type 3 4 for ringer type 4 A confirmation ring will be heard for the new ringer type The phone will automatically exit ringer programming mode TO PROGRAM SPEED DIAL NUMBERS The Handset must be OFF Press MEM PROG The PHONE LED will flash quickly to indicate that the unit is in program mode Using the dial pad enter the number you want to store The number can be up to 16 digits long including pauses or other specia
23. ut the drained battery in the Spare Battery charger for recharging SETTING UP YOUR VTECH VT 1711 Choose an area near an electrical outlet and a telephone wall jack AC POWER ADAPTOR Plug the AC power adaptor into an electrical outlet and the DC connector to the back of the base unit SETTING THE TONE PULSE SWITCH The TONE PULSE switch is located on the bottom of the base unit and is factory set to TONE If you have touch tone service do not change the switch setting If you have rotary Pulse service set the switch to PULSE CHARGE THE HANDSET BATTERY PACK BEFORE USE The battery pack recharges automatically whenever the handset is in the base unit The battery pack must be charged for 16 hours before using your phone for the first time CONNECT TELEPHONE LINE CORD Plug one end of the telephone cord into a wall jack and the other end into the back of the Base Unit GETTING STARTED Please note that the Spare battery pack recharges at a slower rate than a battery pack charging in the Handset It takes 24 hours to fully charge a battery pack in the Spare Battery charger CHECK FOR A DIAL TONE After charging the battery pack rotate the Base Unit antenna to an upright position Pick up the Handset making sure the Handset antenna is fully extended Now press ON OFF you should hear a dial tone If not see IN CASE OF DIFFICULTY Fill in the telephone number card on the base unit CAUTION 1
Download Pdf Manuals
Related Search