Jwin JT-P850 Corded Phone
Contents
1. JT P850 1 Features and Specifications a b c d e f g h D 14 minutes of voice storage time 1M 4 DRAM Voice date time stamp DTS and user prompts Record messages up to 59 OGM up to 50seconds Memo ICM recording up to 1 minute Two default outgoing message OGM Erase each message all messages save all erased messages function Busy tone Ring continuous tone detection 3 digit user selectable remote codes default 000 2digit LED display j DTMF detection for remote control k Answer on off selection indicator and announcement 1 Call screening m Intercept function by stop key or seizing line action n VOX function o New Message LED amp LCD icon indication p 2way Room monitor optional 2 DAM Description and Operation 2 1 Key Operation 2 1 1 ANSWER ON OFF Press to toggle between answer on off It will announce ANSWER ON ANSWER OFF Press and hold for 2 seconds it will announce Security Code and the LED show S and then the security code Press to advance to next digit during security code TIME Press and hold to start the setup of day time Press to play the current day and time OGM FORWARD Press and hold to start recording the answerrecord OGM OGM1 Press once to play OGM1 Press to skip message during message playback Press to increment the digit during DTS or security code setup ME2. procedure will be aborted Press PLAY STOP key to quit the security code setup 2 2 15 Room Monitor While in remote control mode the user can monitor the room status by entering the corresponding tone command In room Monitor State the user can monitor the status from telephone line The duration of room Monitor State is set to 15 seconds 2 2 16 ICM Recording When a call is received in answer record mode the machine will play OGM1 and then performs ICM recording The procedure of ICM recording is as follows Answer the call and then play OGM1 The caller can press to skip OGM play A long beep will be heard and then the ICM recording starts The ICM recording stops if any of the following events occurs i e 8 seconds of silence continuous signal 5 seconds busy tone or record time up to minute or parallel phone picked up or PLAY STOP key pressed If parallel phone picked up is detected the message being recorded will be saved as a new message If press PLAY STOP key the message being recorded will not be saved A long beep tone will be transmitted to indicate that ICM recording is finished If memory full occurs during ICM recording pre recorded OGM2 Memory full please call later will be announced before the machine releases line 2 2 17 Rings Setup Rings detected to enable line interface will be 5 rings or Toll save 2 5 rings PAGE 5 Ifin DAM OFF state
3. the MEMO repeat key for about 2 seconds Release the key after a short beep LED displays o0 Memo recording will then start after a long beep The display will count up from 0 to show the duration of the recording Stop recording by pressing PLAY STOP key once Recording will stop automatically after 1 minute AMSWER ON OFF LED will flash to indicate the presence of new memo ay Conversation Recording ae and hold the MEMO REPEAT key for about 2 second The LED display shows and a short beep is generated Keep pressing the key until the display shows 2A Release the key and two way recording starts Recording will stop if STOP key is pressed or if silence busy tone or continuous tone is detected The display will blink oo and the ANSWER ON OFF LED will flash to indicate the presence of newly recorded conversation Play Memos If new memos and or conversation are recorded the display will blink Press the MEMO REPEAT2WAY key once only the MEMOS eae or ere conversation will be sequentially played The display will stop blinking oo after all memos or conversations have been played The ICM message will not be played However the user may press PLAY STOP key to play all kinds of messages The other procedure is similar to Play all message step If new message s is are record the ANSWER ON OFF LED will flash However if the user just presses ME
4. the rings detected is automatically set to 10 or optional 15 When there is an incoming call ANS OGM LED will flash in the cadences of the ring 2 2 18 Call Screening When a call is received in DAM ON State the machine will play OGM The machine will monitor the pickup of parallel phone after it has seized line for 2 seconds If the machine does not respond to the pickup of parallel phone the user may stop the machine by pressing key on the parallel phone or PLAY STOP key on the machine 2 2 19 Remote Operation 2 2 19 1 To access remote control Call the DAM Wait for OGM to be played Enter the to skip OGM play A long beep tone will be heard Then enter the security code to enter the remote control mode Enter the key combination for the desired function from the table below within 8 seconds Press PLAY STOP key or pick up parallel phone may stop the remote operation 2 2 19 2 Remote control key function and description 3 Repeat or Play Memos press twice to repeat previous message 6 Erase Individual Message O O OC OC 9 Enterthe playback menu _ __ _ _ o O 2 2 19 3 The remote operation voice prompt To play memos press 3 To play messages press 4 To play new calls press 5 To delete all messages press star 4 To stop function press 7 To enter the Playback Menu press 9 2 2 19 4 Playback Menu To repeat message press 3 PAGE 6 To skip mess
5. MO REPEAT Press and hold for two seconds The display shows oo Release key after one short beep to start memo recording PAGE 1 2 2 2 2 1 Ded 2 2 3 2 2 4 2253 Press and hold for four seconds until the display shows 2A Release key to start Two way recording Press once to play recorded memo s and or recorded conversation if any Press to repeat message during message playback Press to decrement the digit during DTS or security code setup ERASE Press once to erase individual messages during message playback Press and hold to erase all saved messages PLAY STOP Press once to play new message s or all message s if any Press to stop message recording or playback Press to quit the setup of daytime stamp or security code Press to screen call while the machine is answering call Press to stop remote control operation OPERATION PROCEDURE Memory Initialisation After power on the machine will run memory check and initial setup The LED display count up from 0 to 15 The machine will then generate a long beep and ready for user setup If memory error is detected LED shows EA Battery Low Detection and Indication If the battery is not installed in the battery compartment or the battery has been used for a long time the LED Lo flashes on to alert the user to replace the battery If a new battery is not installed the messages may be lost once power interruption occ
6. MO REPEAT key to play back messages that LED will keep flashing after the end of playback PAGE 4 2 2 11 Erase and Save all messages Press the ERASE key for about 2 seconds all the messages will be erased after hearing a long beep if the messages exits or an alarm two beep if no message exists Press the ERASE key for about 2 seconds after all messages are been erased the erased messages will be saved after hearing a long beep If any recording action is conducted after all messages have been erased no message can be saved 2 2 12 Answer Record Mode Press ON OFF key will toggle the DAM ON or DAM OFF The PLAY STOP LED will blink if new messages exist The 2 digit LED displays the total number of saved messages 2 2 13 Answer Only Mode When the total number of saved messages exceed 59 or the memory full occurs during recording the answering machine will change to answer only mode automatically 2 2 14 Setup Display the Security Code The security code is initially preset to 000 The code range is from 000 to 999 Procedure of security code setup display is as follows Press ON OFF key for about 2 seconds and release to display current security code Press OGM FORWARD or MEMO REPEAT key to increment or decrement the digit Press ON OFF key for correct digit and advance to the setup of next digit If no key is pressed for 8 seconds the setup
7. age press 5 To delete message press 6 To stop play message press 7 Automatic pause during remote playback of recorded messages While in remote control mode press 4 or 5 to play back recorded messages If the caller does not interrupt the playback and the overall duration of playback reaches 180 seconds the machine will stop playing automatically The machine will generate two short beeps and then single tone beeps to alert the caller If enters any key 0 9 or the machine will continue message playback If enters the machine will release line If fails to enter any key within 8 seconds the machine will generate two short beeps and then a long beep Then the machine will release line That function prevents the remote caller to seize the line for a long time unintentionally 2 2 19 5 Set ADAM ON from OFF state To set ADAM ON state from OFF state Call the ADAM After 8 rings detected the ADAM will seize line and a two beep tone will be heard After the correct security code has been entered the ADAM change from answer off to answer on state and the voice menu will be played The ADAM will release line of no remote key is entered within 8 seconds 2 2 19 6 Intercept Function Press tone to abort OGM play ICM record or remote control after the ADAM has seized line The ICM being recorded will not be saved 3 LED INDICATORS 3 1 ANSWER ON OFF LED 3 2 On to ind
8. icate Answer on mode Flash to indicate new message s recorded Off to indicate Answer off mode 2 Digit LED DISPLAY LED DISPLAY LED STATE DESCRIPTION ENTER POWER DOWN MODE MEMORY FULL ERASE ALL MESSAGES PAGE 7 ON SAVE ALL MESSAGES ee OF THE SECURITY CODE ee THE SECURITY CODE SA ON BLINKING DISPLAY SETUP THE FIRST DIGIT OF Lt PAGE 8
9. ote operation is allowed to perform When memory full occurs during recording or the total number of saved messages exceed 59 OGM2 will be announced to remind the user that no further message can be stored 2 2 5 1 OGMI1 Record amp Playback If the user has not recorded OGM1 before the default OGM1 will be played Press the ANS OGM key for about 2 seconds and release to record OGM1 after hearing a long beep The timer on LCD will start counting up the duration of recording Recording will stop automatically after 50 seconds Pressing ANS OGM key or PLAY STOP key can stop recording OGM1 plays immediately after recording stops Press ANS OGM key or PLAY STOP key will stop playback 2 2 5 2 OGM2 Announce only OGM OGM2 is an answer only message User cannot change OGM2 It is pre stored in the DSP Incoming message cannot be recorded but the remote operation is allowed to perform When memory full occurs during recording or the total number of saved messages exceed 59 OGM 2 will be announced to remind the user that memory full occurs 2 2 6 Playing all ICM Messages At beginning of playback LCD will show the total number of messages meanwhile DAM announces the same content by voice Procedure of playing all messages is as follows 2 2 6 1 Playback Press the PLAY STOP key once the messages will be sequentially played in the order first in first out Only if no new message is recorded or all new message s i
10. s are played otherwise only the new message s will be played If date time stamp DTS has been set the total number of messages DTS is first played Then each message is played with message number DTS played first and clock DTS played last 2 2 6 2 Skip message Press OGM FORWARD key to skip the DTS play or message play and play the next message PAGE 3 2 2 6 3 Repeat message Press MEMO REPEAT key to replay the repeat current message or press twice to replay previous message When last is completed it announces End of message 2 2 6 4 Erase single message Press ERASE key to erase the message currently being played back 2 2 6 5 Stop message play 22 7 2 2 8 2 2 9 2 2 10 Press PLAY STOP key to abort the message play Playing new ICM Messages Procedure of playing new messages is as follows If new message s has have been recorded the ANSWER ON OFF LED will keep flashing Press the PLAY STOP key the new messages will be sequentially played If DTS has been set the total number of messages DTS is first played Then each message is played with message number DTS played first and clock DTS played last The ANSWER ON OFF LED will stop flashing but will be turned on after all new messages have been played to indicate the absence of new messages Recording a Memo Memo is a message left for others who directly access to the answering machine Press and hold
11. urs The security code will be reverted to the default number The user has to record the OGM again or the machine will answer call then play the default OGM Setting the Timer When there is CL blink on the LED display the timer needs setting as the following procedures Press and hold the TIME key for two seconds and release while voice weekday played Press OGM FORWARD or MEMO REPEAT keys to select the right weekday Press TIME key for correct weekday Repeat procedure 1 3 to set hour and minute After setting minute the set time will be announced If no key input within 8 seconds the set up procedure will be abandoned Play the current Time Press the Time key the current will be announced Recording an Out Going Message OGM1 PAGE 2 Auto answer OGM OGM1 is a conventional message requesting the caller to leave a message Record OGM1 as follows If the user has not recorded OGM1 before the default OGM1 will be played Press the OGM FORWARD key for about 2 seconds and release to record OGM1 after hearing a long beep Recording will stop automatically after 50 seconds Pressing STOP key can stop recording OGM 1 plays immediately after recording stops Press STOP key will stop playback Announce only OGM OGM2 is an answer only message The user cannot change OGM2 It is pre stored in the DSP Incoming message cannot be recorded but the rem
Download Pdf Manuals
Related Search