GE JKP20 Electric Single Oven
Contents
1. Hinge Clears Slot Continued on following page Installation Instructions IY Pre Installation Checklist VY Remove the bottom trim from the top of the oven It will be installed at VY Place the oven ona table or platform the end of installation The trim is even with the cutout opening Platform must support 275 Ibs wrapped separately and taped to the top of the unit Installation Instructions Cutout for Built In Oven W Microwave JUNCTION BOX LOCATION Cabinet Width 27 Recommended Cutout Location From Floor 21 5 8 Cutout Depth 23 1 2 Cutout Width 25 Min CABINET WIDTH 27 CUTOUT WIDTH _ 25 MIN 25 1 4 MAX 1 1 Allow 7 8 for overlap of oven over side edges of cutout LI nee 25 1 4 Max Cutout Height 41 1 8 Min I cuTouT 41 1 4 HEIGHT 48 i eee To bottom Overall Height 41 5 8 of junction box Allow a minimum of 20 Overall Width 26 5 8 for clearance to adjacent corners drawers walls etc when doors are open Alternate junction box location _1 7 Niz _ Recommended cutout location Allow 1 for an overlap of oven top and bottom ot cutout NOTE If the cabinet does not have a front frame and the sides are less than 3 4 thick shim both sides If the cabinets do not have a solid bottom then equally to establ2. sure the cabinets and wall cover ings around the oven can withstand the temperatures up to 200 F generated by the oven 1 CAUTION The electrical power to the oven supply line must be shut off while line connections are being made Failure to do so could result in serious injury or death Electrical Requirements This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as noted on rating plate Rating Plate is located on oven side trim We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician After installation have the electrician show you where your main oven disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your oven according to governing codes could result in a hazardous condition If there are no local codes your range must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 70 Latest Edition You can get a copy by writing National Fire Protection Association Battery March Park Quincy MA 02269 Effective January 1 1996 the National Electrical Code requires that new but not existing construction utilize a 4 conductor connection to an electric range When installing an electric range in new construction follow
3. the instructions in the section on NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION You must use a three wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If you connect to aluminum wiring properly installed connectors approved for use with aluminum wiring must be used iy Installation Instructions iY Pre Installation Checklist Remove packaging materials Check behind hinges and under false bottom Remove labels on the outside of the door plastic on trims and panel and all tape around oven Open oven door and remove literature pack broiler pan and grid and oven racks Remove Installation Instructions from literature pack and read them carefully before you begin Be sure to place all literature Use and Care Installations etc safe place for future reference Door Removal is not a requirement for installation of the product but is an added w ZA Za convenience Open the oven door as far as it will go Hinge Unlocked Position Push both hinge locks down toward the door frame to the unlocked position This may require a flat blade screwdriver Place hands on both sides of the door close the oven door to the removal position this is half way between the broil stop and fully closed Lift door up and out until the hinge arms clear the slots
4. Bottom Trim a Place the bottom trim centered over the pre drilled mounting holes Tape the edges of the trim down to maintain the alignment b Using the three pan head trim screws provided secure the bottom trim to the bottom edge of the cabinet IMPORTANT If this unit is ever removed from the cabinet or the cavity is ever pulled out for service the trim must be removed first or damage to the trim will occur D Replacing the Oven Door The oven door is heavy You may need help lifting the door high enough to slide it into the hinges slots Do not lift the door by the handle Replacing the Oven Door Pick the Oven Door up by placing one hand on each side The door is heavy so you may need help Do not lift the door by the handle Place the notch ofthe Bottom Edge Hinge Arm hinge arm into the Of Slot bottom edge of the hinge slot 03 Open the oven door as far as it will open Hinge Notch Hinge in Locked Position 04 Push the hinge locks up against the front frame of the oven cavity to the locked position Notch of Hinge Securely Fitted into Bottom of Hinge Slot Close the oven door Installation Instructions PRE TEST CHECK LIST and any stickers Check to be sure that all wiring is with moving parts secure and not pinched or in contact Remove all protective film if present Vid A Operation Checklist iy Remove all items from the inside of the ov
5. Installation 27 Built In Wall Oven with Microwave Instructions pee If you have questions call 800 GE CARES or visit our website at www GEAppliances com Before you begin Read these instructions carefully and completely e ATTENTION INSTALLER e IMPORTANT Save these instructions for All electric wall ovens must be hard wired local inspector s use direct wired into an approved junction box plug and receptacle is NOT IMPORTANT Observe all governing permitted on these products codes and ordinances e NOTE This appliance must be properly e Note to Installer Be sure to leave these grounded instructions with the consumer e OWNER Keep these instructions for future reference Parts Included Materials Needed Wire Nuts Bottom Trim E M ES Q Strain Relief Junction 8 flat head screws side trim Clamp 3 Pan head screws bottom trim s 36 of String Tools You Will Need 1 8 Drill Bit amp Phillips Electric or Screwdriver Hand Drill Pub No 31 10480 229C4053P460 1 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety e Be sure your oven is installed properly by a qualified installer or service technician e Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure Weight on the oven door could cause the oven to tip and result in injury Never allow anyone to climb sit stand or hang on the oven door e Make
6. e eight 8 screws provided The screws must be a minimum of 1 4 from the front of the cutout b Lift oven into cabinet cutout using the oven opening as an grip Carefully push against oven front frame Do not push against outside edges As you slide the oven back pull the string so that the conduit will lie on top of the oven in a natural loop When you are sure the conduit is out of the way slide the oven 3 4 way back into the opening Remove the string by pulling on one end of the loop NOTE Mounting screws must be used Failure to do so could result in the oven falling out of the cabinet causing serious injury b Secure the oven to cabinet with screws provided NOTE If the cabinet is particle board you must use 4 8 x 3 4 particle board screws These may be purchased at any hardware store Installation Instructions Preparing for the bottom Trim Installation a With oven installed take the bottom trim and center it on the bottom front edge of the cabinet opening Using the trim as a template mark the center of Role Locations each slot three total where the mounting holes will be drilled Remove the trim Remove Lower Trim Before Pre Drilling Mounting Holes Drill pilot holes into the center of each template mark Installing the
7. en Check that conduit is securely connected to the junction box Turn on the power to the oven Refer to your Use and Care Manual Verify that the bake and broil units and all cooking functions operate properly Check that the circuit breaker is not tripped or the house fuse is blown See Use amp Care manual for troubleshooting list 10 Check that the bottom trim is installed properly see page 9 Check to be sure the mounting screws are installed and flush with the side trim See page 9 NOTE TO ELECTRICIAN The power leads supplied with this appliance are UL recognized for connections to larger gauge household wiring The insulation of these leads is rated at temperatures much higher than the temperature rating of household wiring The current carrying capacity of a conductor is governed by the wire gauge and also the temperature rating of the insulation around the wire NOTE ALUMINUM WIRING A WARNING IMPROPER CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN RESULT IN A SERIOUS PROBLEM Splice copper wires to aluminum wiring using special connectors designed and UL approved for joining copper to aluminum and follow the manufacturer s recommended connector procedure closely NOTE Wire used location and enclosure of splices etc must conform to good wiring practice and local codes NOTES Pub No 31 10480 2290 4053 460
8. ish the cutout two braces or runners must be installed to width support the weight of the oven The runners and braces must support 275 pounds 2 x 4 or Equivalent Runners amp 24 NOTE If using equivalent runners then the center of the equivalent runners should be 20 1 2 18 Installation Instructions Electrical Connections ATTENTION INSTALLER All electric wall ovens must be hard wired direct wired into an approved junction box A plug and receptacle is NOT permitted on these products Do not shorten the flexible conduit The conduit strain Relief Clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp If the flexible conduit will not fit within the clamp do not install the oven until a clamp of the proper size is obtained NOTE TO ELECTRICIAN The 3 power leads supplied with this appliance are UL recognized for connection to larger gauge household wiring The insulation of these 3 leads is rated at temperatures much higher than the temperature rating of house hold wiring The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire rather than the wire gauge alone WARNING Improper connection of aluminum house wiring to copper leads can result in an electrical hazard or fire Use only connectors designed for joining coppe
9. ocal codes using wire nuts If the residence red black or white leads are aluminum conductors see WARNING note on preceeding page e Install Junction Box Cover OR 4 Three Conductor Branch Circuit Connection When connecting to a 3 conductor branch circuit if local codes permit Connect the bare oven ground conductor with the crimped neutral white lead to the branch circuit neutral white or gray in color using wire nut Ground Ground and neutral wires Junction Box Cover b Connect the oven red lead to the branch circuit red lead using wire nut c Connect the oven black lead to the branch circuit black lead in accordance with local codes using wire nut If the residence red black or white leads are aluminum conductors see WARNING note on preceeding page d Install Junction Box Cover Installation Instructions Placing the Oven in the Opening Sliding the Oven Into the Drilling the Pilot Holes Opening a Loop do not tie a 36 string around the Note Before drilling the pilot holes conduit before the oven is slid into place make sure the oven is pushed as far This will keep the conduit from falling behind back into the opening as it will go the oven and centered yy 215 Pull out on string a Drill four 1 8 pilot holes through the mounting loop while holes top and bottom of the side trim for pushing the oven iis the Gabinet th
10. r to aluminum and follow the manufacturer s recommended procedure closely Turn off the circuit breaker or remove fuses to the oven branch circuit With the oven in front of the cabinet opening on a table or platform connect the flexible conduit to the electrical junction box as shown below You will need to purchase a strain relief clamp to complete the connection of the conduit to the junction box JUNCTION BOX con 1 LOCATION LONG _ 1 PLACE OVEN ON A SUPPORT TO ASSIST IN CONNECTING CONDUIT Continued on Next Page Installation Instructions Electrial Connections con NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION e When installing in a new construction or e When installing oven in a mobile home or e When local codes do not permit grounding through neutral a Cut the neutral White lead from the crimp Re strip the neutral white lead to expose the proper length of conductor Junction Box Cover b Attach the appliance grounding lead green or bare copper in accordance with local codes If the residence grounding conductor is aluminum see WARNING note c Connect the oven neutral white lead to the branch circuit neutral white or gray in accordance with local codes using wire nut d Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with l
Download Pdf Manuals
Related Search