Zenith VRC420 VCR
Contents
1. No display normal recording Note The SP mode determines how much tape is left and switches speed from SP to EP if necessary to complete recording the program There will be some picture and sound distortion at the point of the speed change Press REC ITR until recording begins The REC indicator light appears in the VCR front panel Recording continues until you reach the end of the tape or until you press STOP to stop recording Press REC ITR repeatedly to select a preset recording time period Each subsequent press of REC ITR increases the recording time by 30 minutes until you reach a maximum of 4 hours Instant Recording Recording one show while watching another Note If you have a cable box connected to your VCR you cannot record one show and watch another Choose the show you wish to record using the VCR s channel selector Choose the show you wish to watch using the TV s channel selector Turn TV and VCR on Place VCR in VCR mode by pressing the TV VCR button on the remote repeatedly until the VCR indicator light appears in the VCR front panel Select channel 3 or 4 at the TV If you have connected your VCR to the TV s A V input jacks select the A V source at the TV for a better picture Select the channel to be watched and recorded at the VCR If you have a cable box select the cable box output channel usually 3 or 4 at the VCR Select cable box channels at the cable box Insert2. Pauses tape temporarily during playback or record PLAY Begins tape playback POWER Turns VCR On and Off Also turns VCR Timer Off and On if programmed QUIT Exits menu system REC ITR Begins tape recording REW Rewinds tape to the beginning SP EP Chooses tape recording speed STOP Cancels playback or record modes V A Adjusts tape playback tracking TV VCR Switches source of TV picture between TV channel and VCR channel selection VCR functions are available in VCR mode Turns VCR On Off Ejects a tape Shows main menu Channel Selectors Enters a Menu Tape Play Record CO E Exits Any Menu Options Direct Channel Fast f i Programming ast forwards picture search through 30 seconds of recording Switches TV Picture between TV and VCR Channel Selectors Adjusts tape Tuner playback tracking To play back the por Chooses Tape tion you just recorded Recording Speed Accesses Tape Counter Display Installing Batteries Be sure to install the batteries provided with this remote Match positive and negative with markings shown in battery compartment Note All VCR operations and menu options can be accessed by using the remote control OPERATION Clock Menu The Clock Menu sets the clock in the VCR to the current time There are two options AUTO and MANUAL Auto Clock Set AUTO automatically sets the clock i
3. 40 Minutes 20 Minutes PAGE 24 OPERATION Playing Tapes This page explains how to use the remote to play tapes on your VCR Auto Manual Tracking Adjustment Your VCR adjusts tracking automatically when you play a tape If the tape was recorded on a different VCR streaks video noise may appear While the tape is playing press TRK W A to adjust the tracking manually Real Time Tape Counter Press ENTER twice to keep the tape counter on the TV screen Press ENTER repeatedly to remove all displays The counter resets to 0 00 00 when you insert a cassette or when a tape is air F FWD rewound to its beginning mE US Fast Forward Pause Slow Motion Video STOP While in play mode Press PAUSE for still video While in still video mode press F FWD or REW for slow motion Press F FWD or REW to control slow speed during slow motion Press PLAY to resume normal tape playing Tape Rewind and Fast Forward While in Stop mode Press and release REW or F FWD Fast Forward as desired Press STOP when tape reaches desired location TRK Tracking Reverse Forward Search V A While in Play mode Press and release REW or F FWD as desired Press PLAY to resume normal tape playing CM Skip Commercial Skip While in play mode Pressing CM SKIP on the remote skips commercials or other program material Pressing 1 2 3 or 4 times skips 30 60 90 or 120 seconds respectively CM SKIP skips a full 120 seconds of co
4. TIME 12 00AM Press number keys then ENTER QUIT exit Press NUMBER 0 9 then ENTER to set date and time SETUP MENU SOURCE TUNER TV TV CATV Auxi Baux2 Press number keys then ENTER QUIT exit Press NUMBER 1 2 3 or 4 to select the desired source SETUP MENU AUTO PROGRAM SEARCHING QUIT exit PAGE 12 INSTALLATION Before you operate your VCR Things you may want to do before you operate your VCR Use CH ADD DEL to Create Favorite Channels Optional Use CH ADD DEL to change the list of active channels found when using AUTO PROGRAM so you can list your favorites See CH ADD DEL on the SETUP Menu page 19 for details Select Other Menu Options Show or hide the VCR status on your screen by using the ON SCREEN DISPLAY option on the SETUP menu We recommend keeping this option ON See the SETUP menu for details If you have a stereo VCR press ENTER to select the audio format HI FI or NORMAL to use when you play a tape We recommend setting this option to HI FI See the PLAYBACK MODE option on the AUDIO Menu for details If you have a stereo VCR press ENTER to select the audio format STEREO MONO or SAP to use when recording We recommend using STEREO See the RECORD MODE option on the AUDIO Menu for details SETUP MENU AUTO PROGRAM CH ADD DEL SOURCE ON SCREEN DISPLAY LANGUAGE SELECT Press number keys QUIT exit SETUP MENU SETUP MENU AUTO PROGRAM CH ADD DEL
5. Carry In Service TV Set Performance Important Warranty Service Warranty begins on the date of original consumer purchase For your convenience keep the dealer s dated bill of sale or a delivery ticket as evidence of the purchase date Read your Operating Guide carefully so that you will understand the operation of your set and how to adjust the customer controls The video product must be taken to a U S or Canadian Zenith authorized service center for warranty service and must be picked up by the owner It is the owner s responsibility to maintain the TV receiver with which the video product is used and the associated antenna system in proper operating condition Product Registration Please fill out and mail your Product Registration Card It is imperative that Zenith know how to reach you promptly if we should discover a safety problem that could affect you For warranty service information contact any Zenith authorized service center Parts and service labor that are Zenith s responsibility see above will be provided without charge Other service is at the owner s expense If you have any problem in obtaining satisfactory warranty service call or write the Zenith Response Center You must provide the model number serial number and date of purchase or date of original installation Before you ask for warranty service read Maintenance And Troubleshooting in your operating guide You might avoid a service call THIS
6. Err message If it is not erased take VCR to an authorized repair center PAUS Record mode is halted SP or EP Displays the recording speed REC VCR is recording STOP Recording is stopped Tuner Messages AU Auxiliary Auxiliary channel is selected for view ing equipment connected to Audio Video jacks on front or rear of the VCR ch VCR tuned to Channel _ HI VCR is turned on BYE VCR is turned off VCR Status Displays CONTROLS AND DISPLAYS PAGE 15 On Screen displays tell you the status of the tape inserted and VCR functions Current mode of operation STOP PAUSE RECORD PLAY etc and audio format of tape where Play HI FI or NORMAL No display Current CH Channel selected by using tuner in VCR Tape Speed SP EP Extended Play LP Long Play SP Standard Play Current date day and time 15 MON 7 17 PX PLAY HI FI VCRCH 11 ST SAP Audio format of signal received by VCR tuner STEREO MONO or ST SAP M 1 35 45 aem Real time tape counter Typical VCR Status Display on TV M 1 35 45 P4 Tape Counter Position VCR Status Display The VCR Status Display appears on the TV when a VCR function starts like when you change a channel or select a different VCR mode For example pressing STOP while the VCR is in PLAY mode shows STOP in the display Press ENTER on the remote at any time except Special Effects Playback
7. Press MENU to see main menu Press NUMBER 1 2 3 or 4 to see desired sub menu to be used Press NUMBER to choose desired option to be changed Press QUIT to exit menu or wait a few minutes and the VCR returns to normal operation Note Perform menu operations with the VCR and TV on and tune the TV to channel 3 or 4 The VCR must also be in the VCR mode of operation Press the TV VCR button repeatedly until VCR indicator light appears in the front panel PAGE 10 INSTALLATION Before you operate your VCR Things you must do before you can operate your VCR Connect the Power Required Plug your VCR into an unswitched 120 Vac 60 Hz household power outlet Turn on the VCR by pressing the POWER on the remote or on the VCR s front panel While plugged into an AC outlet the VCR consumes 3W of electrical power in OFF condition 120V 60Hz Do not plug the VCR into a switched power POWER OUTLET outlet Otherwise when the power is switched off the VCR turns off You may TYPICAL ZENITH VCR then have to reset the time and date and reprogram operational features T EN one p Set Position of the CH3 CH4 Switch Required The CH3 CH4 switch on the VCR s back panel determines which channel the VCR uses to send video signals to your TV The TV must be tuned to the same channel you set with the CH3 CH4 switch to see tape playback and status displays from the VCR
8. SOURCE ON SCREEN DISPLAY LANGUAGE SELECT Press number keys QUIT exit SETUP MENU Press 4 SpeakEZ CLOCK TIMER SETUP AUDIO Press number keys QUIT exit MAIN MENU Press 4 SpeakEZ CLOCK TIMER SETUP AUDIO Press number keys QUIT exit MAIN MENU SETUP MENU CH ADD DEL CH ADD Press number keys then ENTER QUIT exit Press NUMBER 0 9 then ENTER SETUP MENU ON SCREEN DISPLAY ON HoN HOFF Press number keys then ENTER QUIT exit Press NUMBER 1 or 2 to choose ON or OFF AUDIO MENU SpeakEZ ON PLAYBACK HI FI HI FI NORMAL RECORD STEREO Press number keys then ENTER QUIT exit Press NUMBER 1 or 2 to choose HI FI or NORMAL AUDIO MENU SpeakEZ ON PLAYBACK HI FI MONO E SAP Press number keys RECORD STEREO then ENTER Press NUMBER 1 2 or 3 to choose STEREO MONO or SAP QUIT exit Front Panel Diagram CONTROLS AND DISPLAYS PAGE 13 Descriptions of items you need to know to operate your VCR Front Panel Controls These controls perform basic VCR operations some of them light up as you use them The Remote performs basic as well as advanced VCR operations POWER On Off Stop Eject Button Selector Easy Watch Button Cassette and Indicator Compartment PLAY REW Rewind F FWD Fast Forward PAUSE Selector power mstop EZ watet ax2 video 1 a
9. TV input VCR AUDIO RECORD mode is set to SAP or MONAURAL Set VCR AUDIO RECORD mode to Stereo See AUDIO Menu on page 20 PAGE 32 TROUBLESHOOTING Troubleshooting Some quick and easy tips to fixing problems yourself Moisture Condensation Moisture condensation can occur In locations where moisture condensation may occur When the video recorder is moved from a cold place toa Keep the power cord plugged into an AC outlet and warm place POWER On This will help prevent condensation Under extremely humid conditions When condensation has occurred wait a few hours for the VCR to dry before using it Magnetic Field from Other Equipment Keep the VCR and videotapes away from strong magnetic fields such as those produced by a vacuum cleaner refrigerator or air conditioner Video Head Cleaning Your VCR automatically cleans the heads as it is used However after long periods of use your video heads may become clogged with accumulated dirt causing distortion When this occurs use a do it yourself wet type head cleaning cassette available from your Zenith dealer Caution Do not use a dry type head cleaning system It may seriously damage the VCR and cassettes used in the VCR Snow streaking in picture and horizontal pulling indicate the need for professional video head cleaning See your Zenith approved service center for cleaning Cabinet Cleaning Clean the outside surfaces of the VCR with
10. To determine T which video channel provides the best picture for your system try the switch in CH3 position and tune your TV to channel 3 then try the CH4 position and tune your TV to channel 4 For a test display press the TV VCR button on remote repeatedly until the VCR indicator light appears in the VCR s front panel display Press MENU on the remote to see the main menu Select SpeakEZ Function On Off Press 4 A voice tells you how to use the features in the kEZ ON JON HOFF menus if SpeakEZ is ON ON is recommended sprees Ho Ho See the AUDIO Menu for details SpeakEZ RECORD STEREO SETUP CLOCK 8 SpeakEZ only functions with TIMER mmr ENGLISH Press number keys then ENTER QUIT exit Press number keys Press NUMBER 1 or 2 to QUIT exit choose ON or OFF MAIN MENU INSTALLATION PAGE 11 Before you operate your VCR Some things you must do and others you may want to do before you can operate your VCR Select Language for VCR Menus Displays Optional Select English Spanish or French for VCR menus and status displays See the LANGUAGE SELECT option on the SETUP menu for details Set Date and Time for Clock Set the clock in the VCR to the current date and time See CLOCK Menu on page 17 for details Your VCR also has an Auto Clock Set feature See CLOCK Menu for details The Timer feature will not function unless the Clock has been set Select Source for
11. VCR Optional Set the source of the VCR for the type of program signal you have connected to the ANT IN jack on the back of the VCR Choose TV if you have an antenna connected to the VCR Choose CATV if you have a cable system with or without a cable box connected to the VCR Choose AUX1 or AUX2 if you have an accessory Audio Video A V connected to the VCR See SOURCE option on SETUP menu page 19 for details Use Auto Program to Find Channels Required Use AUTO PROGRAM to find active channels in your broadcast area AUTO PROGRAM stores the active channels that you can access by using the CH W A See AUTO PROGRAM the SETUP Menu page 19 for details Press 5 SETUP MENU AUTO PROGRAM CH ADD DEL SOURCE ON SCREEN DISPLAY LANGUAGE SELECT Press number keys QUIT exit SETUP MENU Press 2 CLOCK MENU AUTO CLOCK SET ON MANUAL CLOCK SET Press number keys QUIT exit CLOCK MENU Press 3 SETUP MENU AUTO PROGRAM CH ADD DEL SOURCE ON SCREEN DISPLAY LANGUAGE SELECT Press number keys QUIT exit SETUP MENU SETUP MENU AUTO PROGRAM CH ADD DEL SOURCE ON SCREEN DISPLAY LANGUAGE SELECT Press number keys QUIT exit SETUP MENU SETUP MENU LANGUAGE SELECT ENGLISH ENGLISH FJESPANOL FRANCAIS Press number keys then ENTER QUIT exit Press NUMBER 1 2 or 3 to select the desired language CLOCK MENU MONTH E JANUARY DAY 1 SAT YEAR 2000
12. a soft lint free cloth as required Use care not to scratch the VCR during cleaning Specifications GENERAL Head System Power Source Power Consumption Dimensions Operating Temperature Operating Humidity Timer Weight Tape Speed Tape Width Maximum Recording Time Rewind Time TUNER Antenna VHF Output Signal Channel Coverage VIDEO Video Signal System Input Output Signal to Noise Ratio AUDIO FM audio Frequency Range Dynamic Range Channel Separation Conventional audio Input Output S N Ratio Frequency Range Supplied Accessory SPECIFICATIONS Four head AC 120V 60Hz Approx 15 Watts 360 x 94 x 270 mm 14 2 x 3 7 x 10 6 5 56 35 C 41 F 95 F Less than 80 RH 12 hour display type with AM PM Approx 3 4 kg 7 5 lbs 33 35 mm sec 16 67 mm sec 11 12 mm sec 12 7 mm 2 HOURS T 120 6 HOURS T 120 8 HOURS T 160 Less than 210 seconds T 120 75 ohms 75 ohms Channel 3 or 4 2 13 14 69 1 125 4A A W W 1 W 84 A 5 A 1 EIA Standard 525 lines 60 fields NTSC type color signal 1 0 Vp p 75 ohms unbalanced 1 0 Vp p 75 ohms unbalanced More than 43 dB SP mode 20Hz to 20kHz More than 83 dB More than 55 dB 6 0 dBm more than 47 kohms 6 0 dBm less than 1 5 kohms More than 43 dB SP mode 200 Hz to 10kHz SP mode Hook up Cable VCR to TV 1 Batteries 2 Remote Control 1 Designs and specifications are subject to change without notice We
13. and repeat to choose items in the menu RECORD STEREO Press number keys then ENTER QUIT exit SpeakEZ Turns SpeakEZ ON or OFF A voice tells you how to use the features you select in the menus if SpeakEZ is ON ON is recommended PLAYBACK Selects HI FI or NORMAL for tape playback HI FI High Fidelity provides stereo sound if present on the tape to the left and right VCR AUDIO output jacks on the back of the VCR NORMAL provides monaural sound regardless of the audio format present on the tape RECORD Select the STEREO MONO or SAP for recording a program STEREO records sound from the left and right audio tracks in stereophonic format MONO Monaural records sound in monaural format even if the program is in stereo SAP records the Second Audio Program SAP track if present in addition to the stereo audio tracks SAP usually contains audio in another language Watching TV Through the VCR OPERATION PAGE 21 This page shows a typical video system and explains how to select channels All Channel Antenna Cable TV Wall Jack Y or Direct Cable Zenith Stereo VCR O gt gt Typical Cable Box From Cable TV System Cable Box Output to VCR Selecting Channels when the VCR is OFF 1 Turn TV on 2 Select channel you d like to watch at the TV If you have a cable box select channel 3 or 4 at the TV Select cable box channels at the
14. cable box Selecting Channels at the TV when VCR is ON 1 Turn TV and VCR on 2 Place VCR in TV mode by pressing the TV VCR button on the remote control repeatedly until the VCR indicator disappears from the front panel of the VCR Select channel you d like to watch at the TV If you have a cable box select channel 3 or 4 at the TV Select cable box channels at the cable box Zenith TV VHF UHF CABLE IN VCR Output to TV Channel 3 or 4 when VCR is on and TV VCR is in VCR position VIDEO AUDIO IN IN gt gt gt Audio Video Output to TV Selecting Channels at the VCR when VCR is ON 1 Turn TV and VCR on 2 Place VCR in VCR mode by pressing the TV VCR button on the remote control repeatedly until the VCR indicator appears in the front panel of the VCR Select channels 3 or 4 at the TV If your TV is equipped with A V input jacks check your TV operating manual to select the A V source for a better picture Select the channel you d like to watch at the VCR If you have a cable box select channel 3 or 4 at the VCR Select cable box channels at the cable box PAGE 22 OPERATION Camcorder Connected to VCR This page describes how to connect a camcorder to your VCR Front Panel of Stereo VCR power msstopleject EZ watch Turn off power or unplug VCR before making any connections A V cable is not provided
15. explains the basics of playing tapes in your VCR Automatic Playback No Safety Tab 1 Tape playback begins automatically if the safety tab has m stop eject 4 been removed from the cassette case For example most rental movies have no safety tab Simply insert the prerecorded VHS cassette into the VCR Power will turn on automatically and playback will begin VCR s Controls Select the channel 3 or 4 at the TV or select the TV s AUX Auxiliary source to see the picture if you are using the A V jacks Refer to page 7 and 8 oe Playback Has Safety Tab Cassette Press POWER to turn VCR on Safety Tab Shown in Insert a prerecorded VHS cassette into the VCR Press PLAY to begin playback Select the channel 3 or 4 at the TV or select the TV s AUX Auxiliary source to see the picture if you are using the A V jacks Refer to your TV operating manual Unloading the Cassette from the VCR 1 Press STOP if the tape is playing 2 Press STOP EJECT at the VCR until the cassette is ejected Note This VCR records only in SP and EP speeds Your VCR sets the playback speed automatically to the speed used to record the tape Continued on next page VHS Cassette Playback Record Times Cassette EP Length Standard Play Long Play Extended Play T 30 30 Minutes 1 Hour 1 Hour 30 Minutes T 60 1 Hour 2 Hours 3 Hours 2 Hours 4 Hours 6 Hours 2 Hours 5 Hours 8 Hours
16. indicate the VCR is in the TIMER recording mode OPERATION PAGE 29 Easy Watch Playback Playing back the portion you just recorded Using Easy Watch Playback after timer recording is conve EZ WATCH Button nient You can make timer recordings and play back only and Indicator the portion you just recorded with the timer by pressing a single button later Stop recording when recording without timer EZ WATCH indicator on the VCR lights Note If another operation button is pressed SSS FEM after you stop recording Easy Watch Playback 20 will be canceled video audio r VN E E Press EZ WATCH on the VCR or remote control The tape rewinds to the start of the recorded portion and playback begins Note When you set the timer for more than two timer programs The VCR starts playing back from the earliest one when you use Easy Watch Playback Cy oi e gt V 2 8 la PAGE 30 Troubleshooting TROUBLESHOOTING Some quick and easy tips to fixing problems yourself Before Calling for Service Please refer to this chart before calling for service First turn on the TV and VCR Select appropriate input for the TV to receive the video signal from the VCR You will probably use the Antenna In connection to the TV Select channel 3 or 4 at the TV Place the VCR in the VCR mode by pressing the TV VCR button on the remote repeatedly u
17. power outlet only one way If you re unable to insert plug fully into outlet try reversing the plug If plug still fails to fit contact an electrician to replace your obsolete outlet Do not defeat safety purpose of polarized plug Power Cord Protection Route power supply cords so they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from product Outdoor Antenna Grounding If an outside antenna or cable system is connected to this product be sure antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code USA ANSI NFPA 70 provides information on grounding of mast and supporting structure grounding of lead in wire to an antenna discharge unit connection to grounding electrodes and requirements for grounding electrode See Fig 1 below ___ Antenna Lead in Wire Antenna Discharge Unit NEC Section 810 20 Grounding Conductors a NEC Section 810 21 6 round Clamps Electric Service Equipment Power Service Grounding Electrode System NEC Art 250 Part H PAGE 3 instructions have been adhered to NEC National Electrical Code Antenna grounding per NEC Code ANSI NFPA 70 PAGE 4 SAFETY TIPS IMPORTANT SAFETY INSTRUCTIONS These simple precautions will help
18. LS AND DISPLAYS Front Panel Diagram Message Center Front Panel Display VCR Status Displays OPERATION Clock Menu Timer Menu Setup Menu Audio Menu Watching TV Through the VCR Camcorder Connected to VCR Playing Tapes Instant Recording Recording While You re Away Easy Watch Playback TROUBLESHOOTING SPECIFICATIONS WARRANTY Rear Cover INSTALLATION INDEX Audio Menu Auto Channel Search Connections Channel Add Del Clock Set Easy Watch Playback Features Chart Front Panel Diagram Instant Recording Language Menu Main Menus Message Center Front Panel Display Playing Tapes Remote Control Safety Information Setup Menu SpeakEZ Function Timer Menu Timer Controlled Recording Troubleshooting VCR Status Displays Warranty Watching TV through the VCR PAGE 5 PAGE 6 INSTALLATION VCR Features Chart This page shows the features of your VCR FEATURES SpeakEZ Function Easy Watch Playback 4 Heads Special Video Effects Full Load Quick Start Auto Head Cleaner MTS Hi Fi Stereo Audio System Stereo Audio Video A V Jacks Remote Control SC420T Auto Manual Band Select Auto Manual Channel Search 181 Channel Capability CATV amp TV Record Speeds SP EP Playback Speeds SP LP EP Auto Playback System Auto Manual Digital Tracking Instant Recording Timer Controlled Recording Auto Playback Tape Speed Ad
19. R s memory for access by V A Press 1 to begin search CH ADD DEL Edits the channels found by AUTO PROGRAM Use number keys followed by ENTER to select the channel to be edited e g to ADD channel 3 press 3 then ENTER Press ENTER to ADD or DEL Delete channels to create your own list of favorite channels SOURCE Selects TV CATV AUX1 or AUX2 as the source of the program to watch or record Choose TV if you have an antenna connected to the VCR Choose CATV if you have a cable system with or without a cable box connected to the VCR Choose AUX1 if you want to see the program from accessory equipment such as a camcorder connected to the Audio Video A V IN jacks on the VCR rear panel Choose AUX2 if you want to see the program from accessory equipment such as a camcorder connected to the Audio Video A V IN jacks on the VCR front panel ON SCREEN DISPLAY Selects whether or not you see VCR Status Displays on the TV LANGUAGE SELECT Selects English Spanish or French for VCR menus and displays on the TV PAGE 20 OPERATION Audio Menu The AUDIO Menu specifies the audio format to be used when recording or playing a tape The AUDIO Menu indicates the audio format used when recording or playing a tape 1 Press MENU to see main menu AUDIO MENU f SpeakEZ ON JON 3 Press 1 or 2 to turn SpeakEZ ON or OFF PLAYBACK HI FI 4 Press 4 to see the AUDIO menu Press ENTER
20. STALLER This reminder is provided to call the cable TV system installer s attention to Article 820 40 of the National Electric Code U S A The code provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of the cable entry as practical REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technici
21. TV screen Source for TV is not selected properly Set Input source on TV to Audio Video In or tune TV to Channel 3 or 4 as appropriate TV VCR mode for VCR is set to TV Press the TV VCR button repeatedly to choose VCR mode VCR indicator light appears in VCR front panel Video noise horizontal streaks appear during normal tape playing Tape is a rental or was recorded on another VCR Use TRK w a for manual tracking adjustment while tape is playing Tape heads are dirty Clean video heads VCR Status Display flickers when using STILL video during tape playback Tape tracking needs to be adjusted while in slow motion playback From STILL video mode enable slow motion playback Use TRK w a to adjust tracking for best picture Return to PLAY mode then press PAUSE for STILL video Troubleshooting TROUBLESHOOTING Some quick and easy tips to fixing problems yourself Channel Tuning Problems PAGE 31 Observed Condition Possible Cause Probable Solution Some channels are skipped over when using CH W A Those channels were deleted with the CH ADD DEL option Use CH ADD DEL to restore channels See SETUP Menu on page 19 for details Picture and sound are weak or missing Antenna or cables are loose Tighten connections or replace cable Wrong SOURCE option is being used Recording Problems Try all SOURCE options See SETUP me
22. WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ZENITH SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL INDIRECT OR INCIDENTAL DAMAGES OF ANY KIND INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THE PRODUCT Customer Service Zenith National Response Center 201 James Record Road Building 3 Huntsville AL 35824 Phone 256 772 1515 Fax 256 774 4070 email customer service zenith com ZENITH ELECTRONICS CORPORATION Zenith Part No 206 3615 1000 MILWAUKEE AVENUE GS 3835 0039 GLENVIEW ILLINOIS 60025 2493 Printed in Korea Issue O
23. a VHS cassette tape into the VCR Press SP EP to select recording speed if desired Recording speed is always SP unless you select EP Press REC ITR until recording begins REC indicator light appears in the VCR front panel Recording continues until you reach the end of the tape or until you press STOP to stop recording Place VCR in TV mode by pressing the TV VCR button on remote to turn off VCR indicator light in the VCR front panel Select the show you wish to watch using the TV s channel selector Note To return to the show you re recording select channel 3 or 4 at the TV Place the VCR in the VCR mode by pressing the TV VCR button on the remote to show the VCR indicator light in the VCR s front panel OPERATION PAGE 27 power Q tv vcr Remote s Controls e rec itr VCR s Controls power m stop eject 4 O Options You Can Use While Recording Instant Recording until end of tape PAUSE Momentarily pauses recording Press PAUSE again to resume recording STOP or STOP EJECT Stops and exits recording mode PAGE 28 OPERATION Recording While You re Away This page explains how to use the Timer so that you can record while you are away PROGRAM PROGRAM SpeakEZ MONTH MONTH DAY DAY 2 mes p T SETUP lt STOP STOP AUDIO i 4 CHANNEL CHANNEL SPEED 3 SPEED REPEAT REPEAT Press number keys 1 8 to select program 1 8 to sel
24. an for help CAUTION Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation Unauthorized modification could void the user s authority to operate this product This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Ce appareil num rique de la class b respecte toutes les exigences du R gulement sur le mat riel brouillier du Canada Zenith is a trademark of ZEC O Copyright Zenith Electronics Corporation 2000 SAFETY TIPS IMPORTANT SAFETY INSTRUCTIONS These simple precautions will help ensure that you get many years of safe enjoyment from your new product 1 Read Instructions Read all of the safety and operating instructions before operating the product Retain Instructions Keep all safety and operating instructions for future reference Heed Warnings Follow warnings on the product and in the operating guide Follow Instructions Follow all operating and use instructions Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Attachments Do not use attachments not recommended by product manufacturer as they may cause hazards Water and Moisture Do not use this product near water for example near a bathtub wash bowl sink or laundry tub in a wet basement or near a swimming pool Accessories Do
25. der NOTES PAGE 35 Notes Your Zenith Limited Warranty VIDEO CASSETTE RECORDER OR PLAYER Welcome into the Zenith family We believe that you will be pleased with your new Zenith Entertainment Machine Please read this warranty carefully it is a LIMITED WARRANTY as defined under Federal Law This warranty gives you specific legal rights and you may also have other rights that vary from state to state within the U S A ZENITH S RESPONSIBILITY Service Labor Parts Not Covered During a period of 90 days from effective warranty date Zenith will provide service labor by a Zenith authorized service center when needed as determined by Zenith as a result of manufacturing defects New or remanufactured replacements for factory defective parts will be supplied by a Zenith authorized service center for one year from effective warranty date Such replacement parts are warranted for the remaining portion of the original warranty period This warranty covers manufacturing defects and does not cover installation adjustment of customer controls in the home installation or repair of home antenna systems cable converters or cable company supplied equipment it also does not cover damage due to misuse abuse negligence acts of God or other causes beyond the control of Zenith Any alteration of the product after manufacture voids this warranty in its entirety OWNER S RESPONSIBILITY Effective Warranty Date Operating Guide
26. ect program QUIT exit ENTER to adjust program ENTER to adjust program MAIN MENU TIMER MENU TIMER MENU for Program 1 for Program 8 Timer controlled recording lets you record shows VCR Operation with Timer Off or On unattended Pick a day and time up to one year in advance The show may be recorded once or on multiple days You TIMER can schedule up to eight different events into the PROGRAM STATUS TIMER for recording as long as no events overlap in the same time period VCR OPERATION Off Disables Timer controlled recording if an event is scheduled in the Timer All other VCR operations can be used as desired Place VCR in VCR mode by pressing the TV VCR On or set Enables Timer controlled button on the remote repeatedly until the VCR recording if an event is scheduled indicator light appears in the VCR front panel in the Timer You cannot operate Turn TV and VCR on the VCR manually while it is in Select channel 3 or 4 at the TV Timer Set mode If you have scheduled the Timer you ll be Insert a VHS cassette tape into the VCR recording at a later time Program events to be recorded with the Timer by following the procedure in the TIMER MENU section If you have a cable box select channel 3 or 4 ar the VCR as the channel to be recorded Keep your cable box on when using the Timer to record Enable the Timer by pressing POWER to turn off the VCR The TIMER indicator light appears in the VCR front panel to
27. ensure that you get many years of safe enjoyment from your new product 15 Lightning For added protection for this product during a lightning storm or when product is left unattended 21 Replacement Parts When replacement part s are required be sure service technician has used replacement part s specified by manufacturer or have same characteristics as original part s Unauthorized substitutions may result in fire and unused for long periods of time unplug it from the wall outlet and disconnect antenna or cable system This will prevent damage to product due to lightning and power line surges Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system take extreme care to keep from touching such power lines or circuits as contact with them might be fatal Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in risk of fire or electric shock Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock Never spill liquid of any kind on product Servicing Do not attempt to service this product yourself as opening or removing cover
28. ight and dimensions shown are approximate PAGE 33 Recommended VCR Accessories VHS TAPE REWINDER Most repair work on VCRs and Camcorders is due to excessive Prolong the life of your video equipment with our rewinder ZEN 901 ONLY 14 99 5 WIRELESS INTERCOM SET Kids watching movies in another room Baby in another room as you watch TV Keep tabs on them with our inexpensive intercom set e FM wireless two stations 3 channels plug into standard AC outlets E Relatively noiseless transmission for excellent sound Upgrades to four stations with additional set Units wall mount or set on table ALG 1188 0 N LY 49 9 9 ZENITH 5 FUNCTION REMOTE 6 L a L e 2 Broken or lost remote Need second remote or more functions p Order direct from Zenith Operates TV VCR CD DVD DIVX DSS amp Cable Box 22o e Operates PIP and Most Screen Menus ooo e Extended Range amp MORE Orders 1 year more after product purchase may receive upgraded models Other Remotes with 3 4 5 amp 7 Functions Available Upon Request 0 AOL ZEN 525 0 N LY 1 9 9 9 ee canines e zenith ORDER TODAY CALL OR FAX TOLL FREE 1 800 2 5 5 6 790 PLEASE ALLOW 3 4 WEEKS FOR DELIVERY Fax 1 888 693 6484 ME Oo VISA email parts sales zenith com Use Your Visa or MasterCard to Or
29. just Slow Motion Video 4 head VCR Variable 1 10 to 1 32 Clear Pause Still Video Real Time Tape Counter Speed Search CM Skip English Spanish French Menus 1 Year 8 Event Timer Message Center Front Panel Display Auto Clock Set System Hook up Cable VCR to TV Energy Saving VCR design and specifications are subject to change without prior notice INSTALLATION PAGE 7 Connections for your VCR Required connections for your VCR Connections Without a Cable Box Antenna Flat Wire 300 ohm Back Panel of Stereo VCR so 5 24 300 75 ohm Adaptor Not provided Cable TV CH3 CH4 Wall Jack Back Panel of Typical TV S S D VHF UHF CATV OUT OUT R AUDIO L VIDEO ANT This cable is provided gt with your VCR Turn off power or unplug VCR before making any connections Connections With a Cable Box Back Panel of Stereo VCR Back Panel of Typical TV IN IN VHF UHF CATV R 2 L a ANT VHF UHF CH3 CH4 IN L LINE1 AUX1 Back Panel of Typical Cable Box Cable TV Wall Jack This cable is provided with your VCR Turn off power or unplug VCR before making any connections PAGE 8 INSTALLATION Connections for your VCR Optional connections for your VCR Audio Video A V Connections to TV Use A V connections for a bet
30. machine number VRC420 t i 28 2 yere RECORD YOUR MODEL NUMBER Now while you can see it The model and serial number of your new VCR are located on the back of the VCR cabinet For your future convenience we suggest that you record these numbers here MODEL NO SERIAL NO WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE POWER CORD POLARIZATION CAUTION To Prevent Electric Shock match wide blade of plug to wide slot fully insert ATTENTION Pour viter les chocs lectriques introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu au fond NOTE TO CABLE TV IN
31. mmercials in a few seconds then resumes normal playback OPERATION PAGE 25 Instant Recording Recording what you are watching on TV Options You Can Use While Recording Instant recording lets you record until you reach the end of tv ver sp ep tape or you press STOP to stop recording C c rec itr Turn TV and VCR on Remote s Controls Place VCR in VCR mode by pressing the TV VCR button on the remote repeatedly until the VCR indicator light appears in the VCR front panel power m stop eject 4 Select channel 3 or 4 at the TV If you have connected your VCR to the TV s A V input jacks t the A V he TV f selec the A V source at the or a better VCR s Controls picture Select the channel to be watched and recorded at the VCR If you have a cable box select the cable box output channel usually 3 or 4 at the Instant Recording Instant Timer Recording VCR Select cable box channels at the cable box until end of tape Preset recording times PAUSE STOP or STOP EJECT Momentarily pauses Stops and exits recording recording Press PAUSE mode Press SP EP to select recording speed if again to resume recording desired Recording speed is always SP unless STOP or STOP EJECT Insert a VHS cassette tape into the VCR you select EP Stops and exits recording mode Press REC ITR until recording begins REC indicator light appears in the VCR front panel Recording continues until yo
32. mode SLOW STILL etc to see the Status Display Note If the VCR Status Display does not appear on the TV screen check the ON SCREEN DISPLAY option on the SETUP menu Select ON to see the display See Setup Menu section for details M Counter Memory is active Tape is rewound past index mark 1 35 45 Length of tape in time 121 hour 35 35 minutes 45 45 seconds REM 1 35 Time Remaining VCR Status Display Options When the Status Display appears press ENTER repeatedly to see abbreviated displays as follows 1 2 Press ENTER to see Status Display Press ENTER a second time to show only the tape counter position Press ENTER a third time to show only the tape time remaining Press ENTER repeatedly until all displays are removed PAGE 16 OPERATION The Buttons on Your Remote A quick list of all the buttons on your remote control and what they do V A Channel Selectors Also selects AUX A V input channel CM SKIP Fast forwards picture search through 30 seconds of recording EJECT Ejects the tape from the VCR ENTER Programs menu options and shows VCR display EZ WATCH Press to play back the portion you just recorded F FWD Fast Forward Advances tape rapidly MEMORY Returns real time tape counter to zero M 0 00 00 MENU Shows main menu Numbers Chooses channels and enters programming information PAUSE
33. n the VCR to the current time and date AUTO works only in areas where Data Service DS signals are provided along with normal TV signals CLOCK MENU 1 Press MENU to see Main Menu AUTO CLOCK SET ON MANUAL CLOCK SET 2 Press 1 to see Clock Menu 3 Press 1 to set the current time automatically on the Clock Menu Press number keys QUIT exit Notes We recommend that you set the clock using the MANUAL method the first time you use your VCR See MANUAL option for details The clock must be set before you can record by using the TIMER Manual Clock Set The CLOCK Menu allows you to set the clock in the VCR to the current date and time Notes The clock must be set before you can record using the TIMER menu You may have to reset the clock and other features if a power outage lasts for more than 3 seconds If you use the Manual option The AUTO CLOCK SET mode will be turned to OFF CLOCK MENU MONTH J JANUARY DAY 1 SAT YEAR 2000 TIME 12 00 AM How to Set Clock 1 Press MENU to see Main Menu Press number keys then ENTER QUIT exit Press 1 to see clock options Typical CLOCK Menu with date and time settings Press 2 to adjust your options First insert the month number 5 MAY 6 JUNE etc Press ENTER to move to next option Press QUIT to exit the menu system PAGE 17 PAGE 18 OPERATION Timer Menu The TIMER Menu tells the VCR when to record a program on a day and at a time
34. not place product on an unstable cart stand tripod bracket or table Product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of product should follow manufacturer s instructions and should use a mounting accessory recommended by manufacturer Transporting Product Move product and cart combinations with care Quick stops excessive force and uneven surfaces may cause product and cart combination to overturn a Ventilation Slots and openings in cabinet must not be blocked or covered They are provided for ventilation to ensure reliable operation and to protect from overheating Never block openings by placing product on a bed sofa rug or other similar surface Do not place product in built in installation such as a bookcase or rack unless proper ventilation is provided or manufacturer s 11 Power Sources Operate product only from type of power source indicated on marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to manual Line Cord Polarization Product is equipped with a polarized alternating current line plug a plug having one blade wider than the other As a safety feature this plug will fit into
35. ntil VCR indicator light appears in the VCR front panel If you have a cable box turn it on and select channel 3 or 4 at the VCR Operating Problems Observed Condition No power to the VCR Possible Cause Power cord is not connected Probable Solution Connect power cord Remote does not function No picture appears on TV screen from any VCR function Batteries are weak Replace with new batteries You are too far away from the VCR Move closer to the VCR Remote may be at an awkward angle Source for TV is not selected properly Avoid holding the remote at sharp angle Set INPUT source on TV to Audio Video In or tune TV to Channel 3 or 4 as appropriate TV VCR mode for VCR is set to TV Press the TV VCR button on remote repeatedly to choose VCR mode VCR indicator light appears in VCR front panel VCR features do not function VCR does not respond to remote functions or VCR keys VCR is locked up Playing Tapes Playback Problems Disconnect VCR power cord for three 3 minutes Reset clock and other features as necessary Observed Condition Possible Cause Probable Solution Tape will not rewind or fast forward Tape is fully rewound or is at its end No action necessary Mechanical sound is audible during playback Note This is normal operating sound from internal mechanisms No action necessary Tape playback does not appear on
36. nu on page 19 for details Observed Condition Possible Cause Probable Solution Camcorder image is not shown Camcorder is off Turn camcorder on and operate properly Camcorder image via A V input to VCR is not shown on TV screen VCR SOURCE is not set to AUX Use CH W A to select AUX A V input channel Timer recording is not possible Clock in VCR is not set to correct time Set clock to correct time See CLOCK menu on page 17 VCR is on which disables timer Turn VCR off to enable timer TIMER indicator light appears in the VCR front panel Timer has been programmed incorrectly Reprogram Timer See TIMER menu on page 18 TIMER indicator light does not appear after programming timer Reprogram Timer and turn VCR off to enable timer TIMER indicator light appears after VCR is turned off VCR is in Timer Recording mode This is the normal indication that the VCR is in TIMER mode Stereo Audio Record and or Playback Problems Observed Condition Possible Cause Probable Solution Stereo is not present TV is not Stereo compatible No action is possible Program is not in stereo format No action is possible VCR A V Out jacks are not connected to TV A V In jacks Make A V connections Stereo is available only via A V output from VCR VCR Audio Video Out is not selected for viewing at the TV Select AUX or A V source as
37. rase the program Press QUIT to exit the menu system PROGRAM MONTH DAY START STOP CHANNEL SPEED REPEAT 1 8 to select program ENTER to adjust program Program Number When highlighted press NUMBER 1 8 to choose program Number REPEAT OPTIONS ONCE Records once WEEKLY Records once each week DAILY Records one time each day Monday Friday CHANNEL OPTIONS To select an AUX channel select the next highest or lowest channel programmed in the VCR with the CH W A SPEED OPTIONS SP or EP The SP mode determines how much tape is left and switches speed from SP to EP if necessary to complete recording the program There will be some picture and sound distortion at the point of the speed change AM PM OPTIONS Press 1 for AM Press 2 for PM PROGRAM MONTH 7 JULY DAY 20 THU START 11 16 AM STOP 11 46 AM CHANNEL 20 TV SPEED EP REPEAT ONCE 1 8 to select program To erase press 0 Follow L these steps Press 0 to erase program Setup Menu OPERATION PAGE 19 The SETUP Menu customizes the VCR s operation for your particular needs Press MENU to see main menu Press 3 to see the SETUP menu Press NUMBER to choose desired option to be SETUP MENU changed AUTO PROGRAM CH ADD DEL SOURCE ON SCREEN DISPLAY LANGUAGE SELECT Press number keys QUIT exit AUTO PROGRAM Finds all active channels and stores them in the VC
38. s may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Wall or Ceiling Mounting Mount product to wall or ceiling only as recommended by manufacturer electric shock or other hazards Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under these conditions a b If power supply cord or plug is damaged If liquid has been spilled or objects have fallen into product If product has been exposed to rain or water d If product doesn t operate normally by following handbook instructions Adjust only those controls covered by handbook instructions improper adjustment of other controls may result in damage and often requires extensive work by a qualified technician to restore product to normal operation If product has been dropped or cabinet has been f damaged If product exhibits a distinct change in performance Heat Keep product away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat Safety Check Upon completion of any service or repairs to this product ask service technician to perform safety checks to determine that product is in proper operating condition Contents Index CONTENTS SAFETY TIPS INSTALLATION VCR Features Chart Connections for Your VCR Before you operate your VCR CONTRO
39. ter picture Back Panel of Stereo VCR VHF UHF CH3 CH4 LINE1 AUX1 A V cable is not provided with VCR Accessory Audio Video A V Connections to VCR Back Panel of Stereo VCR VHF UHF CH3 CH4 A V cable is not provided with VCR Back Panel of Typical TV Turn off power A or unplug VCR before making any connections Accessory Component Another VCR Camcorder Video Camera Satellite Receiver Laser Disc Player Jack panel of Accessory Turn off power A or unplug VCR before making any connections INSTALLATION PAGE 9 Before you operate your VCR Things you must do before you can operate your VCR CLOCK MENU oxi SETUP MENU AUDIO MENU DAY SpeakEZ ON JON HOFF AUTO CLOCK SET ON START AUTO PROGRAM EMI MANUAL CLOCK SET STOP CH ADD DEL 2 CHANNEL SOURCE RECORD STEREO 5 ON SCREEN DISPLAY SPEED REPEAT LANGUAGE SELECT Press number keys 1 8 to select program Press number keys Press number keys QUIT exit ENTER to adjust program QUIT exit then ENTER QUIT exit CLOCK TIMER SETUP AUDIO MEINE Press NUMBER 1 2 3 4 button SpeakEZ CLOCK TIMER SETUP AUDIO Press number keys QUIT exit MAIN MENU How to Access Menus Menu operation is easy just follow the instructions shown Point remote toward VCR at the bottom of the menu
40. u reach the end of the tape or until you press STOP to stop recording PAGE 26 OPERATION Instant Recording Recording using preset time periods Preset Time Periods for ITR Recording power Note tyver sp ep Preset recording time counts down until the recording time C2 rec itr is over Instant attended Timer Recording ITR lets you record for Remote s Controls a specific preset time period instead of recording until the end of tape is reached For example you can record a 30 minute show using the preset time period m stop eject 4 Turn TV and VCR on e rec itr Place VCR in VCR mode by pressing the TV VCR button on the remote repeatedly until the VCR indicator light appears in the VCR front panel VCR s Controls Select channel 3 or 4 at the TV If you have connected your VCR to the TV s A V input jacks select the A V source at the TV for a better picture Presses of Preset Time For REC ITR Recording Select the channel to be watched and recorded 1 Press Current Time Until end of tape at the VCR If you have a cable box select the 0 30 30 minutes cable box output channel usually 3 or 4 at the 1 00 1 hours VCR Select cable box channels at the cable box 1 30 1 hour and 30 minutes Insert a VHS cassette tape into the VCR 2 00 2 hours Display Press SP EP to select recording speed if desired 2 Recording speed is always SP unless you select 4 00 4 hours
41. udio r Audio Video A V Auxiliary In Jacks AUX2 Message Center Front Panel Display REC ITR Channel Up Down Instant Timer Selector Record Selector PAGE 14 CONTROLS AND DISPLAYS Message center front panel display Information appears in the Front Panel Display depending on the VCR function being used Clock Tape operation indicator A Cassette is in the VCR VCR is Recording VCR functions are available and channels are selected at VCR Front Panel Display shows which VCR function you are using For example when you press SP EP SP or EP appears to indicate the tape speed As you change channels the channel numbers appear The current time shows even while the VCR is off Playback Messages Err Turn VCR On and OFF to erase Err message If it is not erased take VCR to an authorized repair center FF Fast Forward Tape is advancing rapidly CUE Tape is advancing rapidly in playback mode for visual search CUE Tape is reversing rapidly in playback mode for visual search PLAY Tape is playing at normal playback speed REW Rewind Tape is rewinding rapidly SLW Tape is playing at slow motion speed ST LL Playback is halted on one frame STOP Tape rewind or playback is stopped VCR is in timer recording Time is AM Record Message Err Turn VCR On and OFF to erase
42. with VCR Select AUX for Viewing an Audio Video source like a Camcorder 1 With TV and VCR on place VCR in VCR mode by pressing the TV VCR button on the remote and repeat until the VCR indicator light appears in the VCR s front panel SETUP MENU Select channel 3 or 4 on the TV Note If your TV has A V jacks you may get a better picture if you connect your VCR SOURCE TUNER TV there Then select the A V source on the TV TV CATV AUX1 EJAUX2 At the VCR Channel Down lower than the lowest channel or Press number keys Channel Up above the highest to select AUX2 then ENTER QUIT exit You can also choose the SETUP menu as described below Press MENU to see main menu Press 3 to see the SETUP menu Press 3 for the SETUP menu s SOURCE item Press 4 for AUX2 then ENTER Press QUIT to exit Press 4 to select AUX2 Items in the Menu SOURCE Shows the program source TV CATV or AUX selected for the VCR to receive TUNER The VCR is using its Tuner to receive programs from an antenna or cable TV Selects programs for the VCR from a rooftop type antenna Selects programs for the VCR from Cable TV Selects programs for the VCR from the rear R AUDIO L VIDEO IN jacks where you may have connected your camcorder Selects programs for the VCR from the front R AUDIO L VIDEO IN jacks where you may have connected your camcorder OPERATION PAGE 23 Playing Tapes This page
43. you specify You can specify eight different events to be recorded in a one year period SpeakEZ CLOCK j TIMER SETUP Kj E AUDIO Press 2 a Press number keys QUIT exit Month of Recording Day of Recording Start Time of Recording Stop Time of Recording Channel of Recording Speed of Recording Frequency of Recording How to Use Timer Press MENU to see main menu Press 2 to see the TIMER menu PROGRAM Kl MONTH DAY START STOP CHANNEL SPEED REPEAT 1 8 to select program ENTER to adjust program PROGRAM J MONTH 7 JULY DAY 20 THU START 11 16 AM STOP 11 46 AM CHANNEL 20 TV SPEED EP REPEAT ONCE 1 8 to select program To erase press 0 Press QUIT Timer will be on when VCR is off When the TIMER menu is displayed on screen press the NUMBER button to select the correct month then press the ENTER button again to move the next option or setting When you have entered all of the settings to your satisfaction press QUIT to exit the menu system Note Set the VCR in TIMER mode by pressing POWER to turn off the VCR The TIMER indicator light appears in the front panel of the VCR You cannot operate the VCR manually while it is recording Pressing POWER stops the recording To Erase a Program 1 Press MENU to see main menu Press 2 to see the TIMER menu Press NUMBER 1 8 to select desired PROGRAM to be erased Press 0 to e
Download Pdf Manuals
Related Search