GE Monogram ZEM200SF Microwave Oven
Contents
1. OO Receptacle installed in side wall e If receptacle is located behind oven install receptacle flush with wall to minimize depth 16 minimum depth is required 16 Receptacle installed behind oven flush with wall e If receptacle is located behind oven and I extended into cabinet r 18 18 minimum cabinet depth is required Receptacle installed behind oven extended into cabinet U nder cabinet e Do not install where vents on the sides will be blocked mounting A 3 prong grounded receptacle must be within reach of the oven s 40 power cord but located out of view when oven is installed Allow access for plugging and unplugging do not place receptacle directly behind oven X827 installation Step 1 Install rear holddown brackets Tools and materials required e Accessory kit J X827 for in wall installation 2 Phillips head screwdrivers 1 amp 2 Drill and 3 32 drill bit Centerpunch or nail Pencil and ruler J X827 Parts List 1 Base Pan 2 Rear Duct 3 Side Covers 2 4 Top Trim 5 Bottom Trim 6 Side Trims 7 Rear Holddown Brackets n Screws A 9 required 1 extra B 4 required 1 extra 2 C 10 required 2 extra D 4 required 1 extra E 4 required 1 extra Screw A Screw B Parts Inventory Screw C Installation Microwave Oven2. Screw D Screw E r 120V 60 Hz i Grounded af me Screw B e Set the base pan into cabinet cutout and center left and right Front flange should be pushed back against front wall flush with opening Use the V notch in the base pan front flange to center e Drill two 3 32 diameter holes into the base supporting structure using the two holesin the base pan front flange as a guide any e Drive two screws into the base pan front flange to temporarily hold in place e Slide two rear holddown brackets into slots in the rear of base pan Tongues should be sticking into the base pan and centered in the slot e Mark and drill four 3 32 holes e Install both brackets with 2 screws B e Remove two screws in the base pan front flange and slide the base pan straight out Step 2 Install base pan Step 3 install side covers Remove the four top plug buttons from the top of the microwave oven cabinet Remove any protective film on oven cabinet Place the microwave oven on the base pan centered left to right Note Do not tighten screws until all screws are started e Install side cover by inserting bottom between oven and base pan e Start two screws A through side cover and two screws E through the cover on top into holes where buttons were removed e Install other side cover with screws A Install other top screws E e Tighten a
3. Tape Template 1 to rear of cabinet aligning arrow with hole center line on Template 2 Position remaining piece of Template 2 under cabinet and align hole center line with arrows on Template 1 i J Cut excess paper from center of Template 2 so it will lie flat Distance from right hole center to left hole i center should measure distance indicated on template Tape remaining portion of Template 2 in place lr 13 Finalize under cabin et installation Good Area ss g y 4 E Ca of Bottom Shelf Installation Microwave Oven Door Front of Cabinet a 9 Fa 3 16 With template secured in place check again that hole center lines on Template 2 are straight and that distance from right to left hole center measures distance shown on template e Drill mounting holes Use of safety glasses is recommended to protect the eyes Empty cabinet and remove delicate items from adjacent cabinets Use center punch or nail to make an indentation for centering the drill bit Holding drill straight drill through Template 2 at the four black drilling holes indicated on template e Place solid support such asa stack of books under oven to raise it close to cabinet bottom e Align mounting holes on oven with bolts e Lift oven and insert bolts into mounting holes e Tighten bolts alternately to draw oven up evenly
4. Under Cabinet Mounting n n n nnnnnnnnnnsnnnnnnnnnnnnnnnnnnrsnsss 5 Installation Preparation Electrical SUD DIY 2 uya q ua una aW aa un a dn en ale 6 naWallilinstallatipgikuya n n A kah au uku k kitu 6 7 Uinder Cabinet Mounting anan kaniqa Mannan aisha cnet aiid dlap ened 7 Installation X 827 E EE O A a t aS sh caversols thiveees laadageed a mwa Ya un wama usa aa 8 9 10 Assemble Trim Kib EFaIWYIe2 a a u D u ua umu nian aerated ivan ielnat tet 11 Vie Steal Te Eimi KIEF PANGS a u u u S S ea i ashata aaa De N DAHL Uku 11 Under Cabinet Mounting a gaa u maa ya ayq Wy quna re ae an 12 TO Fillfromelnside sicko u uu E DG E E au us 12 13 To Drill trom Bottom casei eid tat T een S L Qk a k Qu aD a S E a A 13 If Cabinet Hasa Partition uuu sn ul aa l u ala auqacauauas haah Q a hyaw uB 13 Finalize Under Cabinet Installation LU aana an aC A a LAS qaa 14 M odd available Dimensions and clearances Installation options Advance planning ZEM200 Series Electronic microwave ovens available in black white and stainless steel A 12 5 16 284 mm Design Information Microwave Oven B 23 13 16 605 mm C 11 3 16 284 mm includes feet will require wall space 26 1 8 W x 16 1 4 H for clearance Note When installed trim kit 24 7 8 1 16 This microwave oven can be used on the countertop built into a wall or suspended beneath a cabinet e Ac
5. 2 inside the cabinet with front edge even to cabinet front edge Position template 1 on front of the cabinet so that the arrow is aligned with the hole center line on template 2 12 To drill from inside continued To drill from bottom If cabinet hasa partition Installation Microwave Oven Position remaining piece of Template 2 inside cabinet and align hole center line with arrows on Template 1 Cut excess paper from center of Template 2 so it will lie flat Distance from right hole center to left hole center should measure distance indicated on template Tape remaining portion of Template 2 in place e With template secured in place check again that hole center lines on Template 2 are straight and that distance from right to left hole center measures distance shown on template e Position Template 2 flat against underside of cabinet If cabinet is less than 12 deep cut that amount off front edge of template If cabinet has a front rail cut front edge of template to fit place cut edge against back of front rail Cut template to fit around corner brackets or glue blocks underneath cabinet If cabinet has partition Cut Template 2 into two pieces to fit on I either side of partition Align front edge of one template piece with NN front edge of cabinet or back of front rail CT I tape in place
6. GE Monogram Installation Instructions Under Cabinet Installation and JX 827 Series Built In Kit Microwave O ven M odds ZEM 200 Series Before you begin Read these instructions completely and carefully IMPORTANT Save these instructions for local inspector s use IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES NOTE TO INSTALLER Be sure to leave these instructions with the Consumer NOTE TO CONSUMER Keep these instructions with your Use and Care Book for future reference This appliance must be properly grounded See Electrical Supply page 6 If you have questions concerning the installa Proper installation is the responsibility of the tion of this product call the GE Answer installer Product failure due to improper Center Consumer Information Service at installation is not covered under the GE 800 626 2000 24 hours a day 7 days a week Appliance Warranty See the Use amp Care If you received a damaged microwave oven Guide for warranty information you should contact your dealer Contents Design Information Model Available six ctf tiie ditt Galt at el a Cama an abel etl aoe 3 Dimensions ANd Clearances n nn nn nn n nsn 3 Installation Options iiiaae uD uw A Qa wat Ao avn a ee a aa 3 Advance Planning a a aS shu aaa Q Aka an apa Steet 3 Cabinetry In Wall Installation a aan a A a ede een i ie 4 Installation with Single OVenri a a id ann aW qa Blau ded aiwindndraus aie 5
7. and secure it to cabinet bottom Remove oven s rubber feet and save for future use e Plug power cord into receptacle Bracket Side of Microwave Remove template and clean drill holes e Select four bolts one of each size from parts package Hold each bolt against cabinet front rail e Select bolt that extends beyond top of bottom shelf by 3 16 to 3 4 Correct bolt length isimportant If bolt is too short it won t reach oven if bolt is too long oven will not be drawn up tight to cabinet From inside cabinet insert four bolts all same length through mounting straps and then into drilled holes of cabinet shelf 14 Notes Microwave Ovens 15 Monogram General Electric Company Louisville KY 40225 NOTE While performing installations described in this book safety glasses or goggles should be worn To obtain specific information concerning any Monogram product or service call GE Answer Center consumer information service at 800 626 2000 any time day or night For M onogram local servicein your area call 1 800 444 1845 NOTE Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice Pub NO 495893 Part No 164D3333P128 1997 GE Appliances N D 881 10 97
8. cessory kit JX 827 is necessary for custom in wall installation Available in white black and stainless steel e Do not install into a wall or cabinet without JX 827 This trim kit provides openings for ventilation e Do not install this microwave oven above a cooktop range or other heating surface Refer to Installation for complete details on preparation for in wall installation If you wish to mount the ZEM 200 beneath a cabinet e Cabinet must be wood or metal in good condition The cabinet must be capable of supporting the items in the cabinet plus an additional 90 pounds from the bottom e Wood cabinet bottom must be at least 3 16 thick masonite or plywood e Underside of cabinet must be at least 24 wide 5 1 16 Min 7 naa In Wall TQ 15 116 Min e Using the accessory kit this microwave oven can be installed alone or over any Monogram single electric wall oven All necessary hardware for under cabinet installation comes packed with the product Before installing consult installation instructions packed with product for current dimensional data To obtain ahead of time order Pub No 31 1130 for U nder Cabinet Installation Order Pub No 31 1163 for Built In Accessory Kit JX827 Call GE Publications 800 848 7722 e 12 deep cabinet is preferred though oven may be mounted on shallower cabinetry A 3 prong grounding wall receptacle must be within r
9. each of the 40 power cord Receptacle should not be directly behind oven but should be out of view when oven is installed e Check that cabinet is securely installed using more than two screws at top If not add two screws at cabinet bottom making sure they enter wall studs at least 1 2 e Refer to Installation for further details In wall installation Installation Preparation M icrowave Oven Tools and materials required 3 8 thick plywood min eet s e 2 x 4 lumber Inside Saw 16 Min Screws and screwdriver or other hardware for construction of l plywood base 15 1 16 The opening must be 24 7 8 1 16 wide 15 1 16 high With approximately 1 1 4 for oven trim ee overlap around all edges of opening ee Deep enough to accommodate electrical receptacle and permit adequate air circula tion for proper venting Minimum 18 deep with receptacle inside cutout L nae M in Minimum 16 deep with receptacle outside cutout Height from floor may vary according to preference of user Note When installed trim kit will require wall space 26 1 8 W x 16 1 4 H for clearance Within opening of appropriate dimensions e Install a level base of plywood Flush with lower edge of opening Entirely covering floor of opening e 3 8 thick min plywood must be sup ported by 2 x 4 or 1 x 2 equivalent Opening Cabinet runners on all
10. h Pencil and ruler Scissors Hammer Tape Safety glasses Two brackets supplied ease lt Right Side Ea ss oom oA oR eS NO eh ee ai l emplate 1 e Carefully remove the four plastic plug buttons from oven top and the two screws at top rear flange of case e Remove the two top case screws on the back of oven Retain screws e Select correct template and rear brackets for this model See Template Rear Bracket emplate 2 Reference Sheet e Secure the two rear brackets to back of the oven left and right using screws removed Mounting holes for the oven should be drilled earlier from the inside if cabinet shelves are remov Make sure brackets are level and flush with able to allow enough space H oles may be top surface of case drilled from bottom if necessary e Cut Template 1 along dotted lines Place template 2 inside the cabinet If cabinet is less than 12 deep cut off front edge of template to fit using template cut lines as a guide If cabinet has a recessed shelf measure the thickness of the front rail and cut that amount off the front edge of template This will allow template 2 to lie flat e If you have a partition you must Cut Template 2 into 2 pieces to fit each side of the partition Position one piece of Template
11. ll screws e Remove screw located on the top left of the back of the oven Retain screw Installation Microwave Oven Remove 4 Plug Buttons Remove and Save Screw Screw A Screw E Installation Microwave Oven Step 4 Rear Duct Install ak rear duct 2 Screw C io Partition in Base Pan ase Pan Install rear duct by inserting into bottom e Drive one screw into the rear duct side flange between the oven and back of base flange near the lamp cover pan e Drive three screws through the base pan into The rear duct should be as far to the left as the rear duct bottom possible between the base pan back flange Replace the screw removed from the top left and the partition on the right side to complete the rear duct e Locate and use screws A The base pan should be completely sealed to e Drive one screw through the rear duct into the microwave oven in the back the partition in the base pan Step 5 Install microwave oven Caution Do not pinch power cord V Notch Screws Plug the power cord into the wall receptacle Drive two screws through the base pan front e Gently slide the microwave oven assembly flange through the holes drilled initially into the cabinet opening keeping it centered e Push to the back allowing tongues of rear brackets to slide through rear slots e Check to be sure oven is centered e Locate and
12. mp S additional 90 pounds from the bottom Refer x to Advance Planning for more details Bracket Side of Microwave Installation Preparation Microwave Oven Electrical Tools and materials required 3 prong grounded electrical receptacle su pply Electrical cable 2 wire with ground No 14 minimum as required Monogram microwave ovens require a 120 volt 60 Hz power supply protected bya time delay fuse or circuit breaker These ovens are supplied with a power cord 40 long for which a properly grounded 3 prong electrical receptacle is required 800 watt oven draws 1300 watts with a 12 5 amp load Note Do not use an extension EC 705 test procedure cord with these appliances In wall Install a 3 prong grounded receptacle e Receptacle may be within opening shaded 18 Min In sta atl on area in diagram Receptacle If using this installation be sure opening is Hes sufficiently deep to accommodate power Receptacle cord and plug 18 min Outside e Receptacle may also be placed outside shaded area within reach of oven s 40 power cord In this case opening need only 15 1 16 be 16 deep 2 7 8 ail Installation Preparation Microwave Oven In wall When cabinet depth isa critical factor A receptacle should be installed in a side wall installation at rear of opening continued 14 5 8 minimum cabinet depth is required 14 5 8
13. sides ye Nf ey e Finished floor must support a minimum of aoe ie eS s 100 pounds k Sas i 2x40r1x2 ee JX 827 accessory kit may be assembled and Equivalent runners ee installed at this time Refer to Installation must support base for instructions of all 4 sides TheJX 827 accessory kit provides trim strips to conceal all raw edges of cabinets With single oven Unde cabine mounting Installation Preparation MicrowaveOven Refer to diagram at 24 7 8 1 16 right for dimensions Q ait sss 2 when installing above ea ss a Monogram single n a oven 2 Sa n if I 15 1 16 Il I mee ee I s ra Per Oven 5 7 Requirement Note Trim kit J X827 is as required for installation above IN 3 Vee a single oven Beye 22 Within opening of appropriate dimensions Install a level base of plywood Flush with lower edge of opening Entirely covering floor of opening 3 8 thick min plywood must be sup ported by 2 x 4 or 1 x 2 equivalent runners on all four sides e Finished floor must support a minimum of 100 pounds e Assemble JX 827 accessory kit refer to Installation for details These microwve ovens may be installed under virtually any cabinetry and is supplied with sf Front of Cabinet all hardware necessary for under cabinet installation The cabinet must be capable of supporting the items in the cabinet plus an T a
14. use screws C 10 Step 6 Assemble trim kit frame Step 7 Install trim kit frame Assemble top bottom and side ot trims with four screws D as illustrated Side When assembled top bottom and side strips must be flush Screw Bottom Trim Note Bottom trim has a hinge notch and is not interchangable with top trim Caution Do not overtighten screws doing so could cause misalignment of top and side strips Use the assembled frame as a template Insert the frame into the cut out and locate the attaching holes e Temporarily hold the frame in place by starting the four screws that attach the frame to the base pan and side covers Push frame as far left as possible drive the four screws e Check to be sure door clears the trim when open oe Top Trim x Installation MicrowaveOven Screw D Side Trim Screw Wall Installation Screw C e Mark the four holes on the side of the trim Remove the frame e Center punch and drill 3 32 pilot holes e Position the assembled frame around the oven and secure with 8 screws C using the smaller Phillips head screwdriver to prevent burring the Phillips head 11 Unde cabinet mounting To drill from inside Installation Microwave Oven Tools and materials required Flat blade screw driver Phillips screw driver Drill and 1 4 bit Nail or center punc
Download Pdf Manuals
Related Search