GE JGSP28CEK Gas Kitchen Range
Contents
1. Max depth of cord plug Countertop depth E an recept box 25 typical geze ae tom genoa Peay 4 to prevent 1 1 4 min countertop interference N to top of drawer with drawer AN 2 1 2 Acceptable gas line and x electrical outlet area 29 15 16 min 30 1 16 max 9 STANDARD INSTALLATION If the construction of your cabinet cannot provide a 1 4 flat area at the back of the countertop opening consider changing the countertop to accommodate this dimension See Alternate Construction section 1 13 16 Flat area 1 4 min I i R flat NE I 25 X lca ik l 23 3 16 typicall Le i 9 16 Siar 36 min gt min 1y gt gt lt 29 15 16 30 1 16 gt smooth cut NOTE A 1 1 2 minimum space must be maintained between the rear edge of the cooktop and the rear wall above the cooktop Installation Instructions ELECTRICAL CONNECTIONS INSTALLATION ELECTRICAL CONNECTIONS A Because of potential safety hazards under certain conditions we strongly recommend against the use of an extension cord However if you still elect to use an extension cord it is absolutely necessary that it is a UL listed 3 wire grounding type appliance extension cord and that the current carrying rating of the cord in amperes is equivalent to or greater than the branch circuit rating Such extension cords are obtainable through you2. and range cooktop may occur Forcing the cooktop to fit may cause excessive gaps and could chip the enamel cooktop To obtain Kits a Visit GE Web Site See page 1 b Call GE Answer Center See page 1 c Contact Dealer 2 MOVE RANGE INDOORS IN FRONT OF CABINET OPENING Do not use hand trucks when moving the unpackaged range Cooktop enamel may be chipped 3 PROTECT THE KITCHEN FLOOR Flatten and place a piece of the shipping carton in front of the installation location to protect the flooring NOTE Do not remove the protective channel from the sides of the cooktop if applicable until later in the installation Protective Channel on some models 4 CAREFULLY TILT RANGE TO ACCESS RANGE LEVELING LEGS Use an adjustable wrench to screw leveling legs out so that cooktop support flanges clear top of countertop Installation Instructions 5 REMOVE THE DOOR IF NECESSARY Door removal is not a requirement for installation of the product but is an added convenience To remove the door A UNLOCK HINGES Push both hinge locks down toward the door frame to the unlocked position This may require a flat blade screwdriver unlocked position POSITION DOOR Place hands on both sides of the door and close the oven door to the removal position This is half way between the broil stop and fully closed 5 REMOVE THE DOOR IF NECESSARY cont C LIFT OFF DOOR Lift door up and out until t
3. for leaks Be sure all leaks are stopped before lighting burners Installation Instructions C PRESSURE TEST INFORMATION The maximum allowable supply pressure for the regulator is 14 W C The minimum supply pressure needed to check the regulator setting is 7 W C for natural gas and 10 W C for LP gas AWARNING The range and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of the gas supply system at test pressures of more than 1 2 psig pounds per square inch gauge The range must be isolated from the gas supply piping system by closing its individual shut off valve during any pressure testing of the gas supply system at test pressures equal to or greater than 1 2 psig NOTE 1 2 psig 13 855 w c D CHECK THE IGNITERS Operation of the electric igniters should be checked after the cooktop and supply line have been carefully checked for leaks and the cooktop has been connected to the electrical power a Turn on gas b Push and turn a burner valve to the LITE position e The burner valve should light when gas is available to the burner e Once the burner lights it should be turned out of the LITE position c Try each valve separately until all burners have been checked E BURNER IGNITION Cooktop Spark Ignition When you turn the cooktop knob to LITE the spark igniter makes a series of electric sparks ticking sounds which light
4. the burner During a power failure the burners will not light automatically In an emergency a cooktop burner may be lit with a match by following the steps below AWARNING Lighting gas burners with a match is dangerous You should match light the cooktop burners only in an emergency a Light a match and hold the flame near the burner you want to light Wooden matches work best b Push in and turn the control knob slowly Be sure you are turning the correct knob for the burner you are lighting NOTE If the burner does not light within five seconds turn the knob off and wait five minutes before trying again F BURNER FLAMES Turn each burner on Turn each burner knob to the high position Flames should be blue in color with little or no trace of yellow The burner flames should not flutter or blow away from the burner The inner cone of the flame should be between 1 2 and 3 4 long If the burner flames are yellow in color or not the proper length call GE Service 1 2 to 3 4 _ lt _ COOKTOP BURNER Flames should circle burner Burners should be checked frequently AWARNING If you attempt to measure the inner cone of the flame please use caution Burns could result Installation Instructions INSTALL THE RANGE CONT BAKE AND BROIL BURNERS If the bake and or broil burners have lifting or lazy floating flames or you have a yellow flame perform the following pr
5. Building 451 7th Street S W Washington D C 24010 ANTI TIP DEVICE AWARNING To reduce the risk of tipping the appliance must be secured by properly installed Anti Tip bracket packed with this appliance To check if the bracket is installed and engaged properly carefully tip the range forward The anti tip bracket should engage and prevent the range from tipping over AWARNING e All ranges can tip e Injury to persons could result e Install Anti Tip bracket packed with range AS e See Installation Instructions If you pull the range out and away from the wall for any reason make sure the Anti Tip bracket is engaged when the range is pushed back against the wall Installation Instructions PRE INSTALLATION CHECKLIST 1 INSPECT INSTALLATION LOCATION Refer to alternate construction section for the following non standard installations A Counter opening extends to the wall Maintop Filler supplied with the range see page 15 for Installation Instructions or Backguard Kit JXS32XX Counter height greater than 36 3 4 Lower Trim Slide In Kit JXS56XX C One side is not enclosed by a cabinet Bodyside Kit JXS77XX Island Installation To provide an optimum installation the top surface of the countertop must be level and flat lie on the same plane around the 3 sides that are adjacent to range cooktop Proper adjustments to make the top flat should be made or gaps between the countertop
6. Installation Instructions IN THE COMMONWEALTH OF MASSACHUSETTS e This product must be installed by a licensed plumber or gas fitter e When using ball type gas shut off valves they shall be the T handle type e A flexible gas connector when used must not exceed 3 feet BEFORE YOU BEGIN Read these instructions completely and carefully s IMPORTANT Save these instructions for local inspector s use e IMPORTANT ovserve ail governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions for future reference e Product failure due to improper installation is not covered under the Warranty A WARNING This appliance must be properly grounded IMPORTANT Leak testing of the appliance shall be conducted according to the manufacturer s instructions e Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under warranty 31 10598 1 11 04 JR Gas Slide In Range JGSP28 PARTS INCLUDED gt Z Screws Anti Tip Bracket Rear Filler 2 Screws MATERIALS YOU MAY NEED Joint Sealant Pipe Fittings Shut Off Valve CSA Approved Flexible Gas Line 3 8 Min ID 1 2 NPT Connection 3 foot Maximum Length Massachusetts Only TOOLS YOU WILL NEED ECCE 1 4 Nut Driver GEc
7. OOR wooD Ron Bracket side Rear leveling eveling leg FLOOR CONCRETE 12 INSTALL THE ANTI TIP BRACKET cont INSTALL THE BRACKET IN WOOD OR CONCRETE INSTALLATION WOOD CONSTRUCTIONS a Locate the centers of the 4 holes identified in Fig 1 as Floor Wood and Wall b Drill a 1 8 pilot hole through the pre marked areas Note the angle of the wall screw in Fig 2 c Mount the Anti Tip bracket with the 4 screws provided Top front edge of countertop lt 25 Bracket Screw Wall plate must enter wood or metal LIILITTTITITTTTLLILILLILLLLL LL E LLALILLILELITLITTLLLELTL TL INSTALLATION CONCRETE CONSTRUCTIONS a For concrete installation you will need two 1 4 x 1 1 2 lag screws and two sleeve anchors Locate the center of the 4 holes identified in Fig 1 as Floor Concrete and Wall Drill the recommended size holes in each Install the sleeve anchors into the predrilled concrete holes and install the lag and wall screws through the Anti Tip bracket Make sure the screws are securely tightened INSTALL THE RANGE CONT Installation Instructions 13 SLIDE RANGE INTO OPENING A c Position the range in front of the cabinet opening Make sure that the cooktop edges that overhang the countertop clear the countertop If necessary raise the unit by lowering the leveling legs Push while lifting the range into the opening
8. Phillips Head Screwdriver Tape Measure Wrench or Pliers for 1 7 16 Nut Safety Glasses Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY AWARNING If the information in this manual is not followed exactly a fire explosion or gas leak may result causing property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU STOP SMELL GAS e Do not try to light any appliance Do not touch any electrical switch do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier This range has been design certified by UNDERWRITERS LABORATORIES You ll find safety precautions in your Owner s Manual Read them carefully e Installation of this range must conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI Z223 1 Latest edition e Be sure your range is installed properly by a qualified installer or service technician e To eliminate reaching over surface burners cabinet storage above burner should be avoided e Do not install the unit near an outside door or where a draft m
9. appliance E Before making gas connections make sure that the oven shut off lever visible at the back of range is in the open position Gas supply to top burners Pressure regulator as seen from front of range Oven shut off lever shown in 11 MAKING THE CONNECTIONS cont Install 1 2 flare union adaptor to the 1 2 NPT elbow on pressure regulator Connect flexible appliance connector to flare union Move range into approximate position and connect flexible connector to gas supply line with proper flare union adaptor Shut off valve Flexible gas line Pressure regulator 90 street Gas elbow supply line 1 To prevent gas leaks put a pipe joint sealant or Teflon tape on all male threads NOTE Make sure sealant or tape is compatible with Natural and LP gases When you are finished making connections be sure that all range knobs are turned to OFF before you open the main gas supply valve A WARNING Do not use a flame to check for gas leaks Use liquid leak detector at all joints and connections to check for leaks in the system Installation Instructions INSTALL THE RANGE 12 INSTALL THE ANTI TIP BRACKET A LOCATE THE BRACKET a Decide whether the bracket will be installed on the right or left side of the range opening b Place the bracket as shown in Fig 1 Ry Qua al Fig 1 th Shag ide L de a NN PS Penin 2 Adjacent Yj gt 82 Cy cabinet Cm a Ron FL
10. ay affect its use Installation Instructions ELECTRICAL REQUIRMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as noted on the rating plate Rating plate is located above the storage drawer below the oven frame We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician After installation have the electrician show you where your main range disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your range according to governing codes could result in a hazardous condition If there are no codes your range must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 7O Latest edition You can get a copy by writing National Fire Protection Association Batterymarch Park Quincy MA 02269 Be sure the installation of this product in a mobile home conforms with the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 If this standard does not apply you must follow the standard for Manufactured Home Installations ANSI A225 1 and Manufactured Home Installations Sites and Communities and ANSI NFPA 501A or with local codes You can get a copy of the Federal Standard by Writing Office of Mobile Home Standards HUD
11. d position Remove and replace making sure the rail is in the guide Hinge in locked position A Notch of hinge securely fitted A SS into bottom of hinge slot E Close the oven door Installation Instructions INSTALL THE RANGE CONT COOKTOP BURNERS A ASSEMBLE THE BURNERS ACAUTION The electrode of the spark igniter is exposed Be careful not to snag the electrode of the spark igniter with a cleaning cloth Damage to the igniter could occur Be careful not to turn on any cooktop controls while cleaning A slight electrical shock might result which could cause you to knock over hot cookware a Place burner heads over the electrodes on the cooktop in the correct locations according to their sizes Medium head Small head and cap and cap Front of range Large head Large head and cap and cap b Make sure the slot in the burner head is positioned over the electrode COOKTOP BURNERS cont A ASSEMBLE THE BURNERS cont c Place the matching size caps onto the heads Make sure that the heads and caps are placed in the correct locations Place the vent grille grates and air inlet cover onto the cooktop making sure that the grates lock the vent grille in place Grate Ets Burner cap CHECK FOR LEAKS Turn the gas supply on and use a liquid leak detector soap solution at all joints and connections to check for leaks Do not use an open flame to look
12. er gaps between range sides and cabinet Refer to the kit instructions for installation details E CABINETS OVER THE RANGE LESS THAN 30 If a 30 clearance between cooking surface and overhead combustible material or metal cabinets cannot be maintained protect the underside of the cabinets above the cooktop with not less than 1 4 insulating millboard covered with sheet metal not less than 0 0122 thick OPERATION CHECKLIST e Double check to make sure everything in this guide has been completed Rechecking steps will ensure safe use of the cooktop Make sure all controls are left in the OFF position Make sure the flow of combustion and ventilation air to the cooktop is unobstructed The serial plate for your Range is located under the oven door above the storage area In addition to the model and serial numbers it tells you the ratings of the burners and the type of fuel and pressure the cooktop was adjusted for when it left the factory When ordering parts always include the serial number and model number to ensure proper replacement parts Recheck Steps Double check to make sure everything in this guide has been completed Rechecking steps will ensure safe use of the Range 16 Please see L P conversion instructions supplied with this range when L P Gas is used NOTE Instructions are mounted on regulator bracket IN SOME CASES A With L P gas some yellow tipping on the outer cone is nor
13. ghten the air shutter screw Inner cone of Check the inner flame cone of the flame 1 2 to 3 4 4 Oven broiler It should be burner between 1 2 and 3 4 long for the oven bake and broil burners WHEN ALL ADJUSTMENTS ARE MADE AND THE RESULTS ARE SATISFACTORY 1 Replace the orifice fitting cover 2 Replace the burner baffle flame spreader and screws 3 Replace the oven bottom 4 Replace the oven door Installation Instructions ALTERNATE CONSTRUCTION PREPARATION OPTIONAL MAINTOP FILLER OR BACKGUARD KIT If counter opening extends to the wall it will require Maintop Filler Kit supplied with the range or Backguard Kit JXS32XX to close the gap NOTE If the countertop is greater than 25 it will show a gap between the backguard and wall or between filler kit and the wall If the countertop is less than 25 a gap will occur between the countertop front and the control panel ends see Step 13G If you are using the optional backguard kit refer to the backguard kit instructions for installation details Must gt lt ___ 30 gt be smooth cut Must be flat flat lt Must be level gt 31 1 8 If you use the filler kit place the metal filler piece supplied with the range to the back of the range as shown in the figure below Start the 2 screws into the upper holes at the outside rear of the range above the louvers and through the slots in
14. he hinge arms clear the slots DO NOT LIFT THE DOOR BY THE HANDLE NOTE The oven door is very heavy Be sure you have a firm grip before lifting the oven door off the hinges Use caution once the door is removed Do not lay the door on its handle This could cause dents or scratches Hinge clears slot 6 REMOVE PACKING MATERIALS Also remove labels on door plastic on trim and panel and all tape around the range REMOVE STORAGE DRAWER A Pull the drawer out until it stops Lift the front of the drawer until the stops clear the guides Guide C Pull forward and remove the drawer Installation Instructions PRE INSTALLATION CHECKLIST CONT PRE INSTALLATION CUTOUT AND REQUIRED CLEARANCES If cabinets are placed less than 30 above the range gt OVERALL DEPTH see Alternate Construction Step 19F on page 16 tial NOTE Product meets ANSI Z21 1 requirements for 0O clearance to back and side walls below the cooktop Wall coverings counters and cabinets around range must withstand heat up to 194 generated by the range Follow instructions packaged with alternate appliance 6 min from walls E 30 min from For optimum 24 min cooking surface installation these to bottom of surfaces must be overhead aT flat and level i 2393 1 e7 C lt 13 p 18 min vertical distance ase dept from the bottom of the we adjacent overhead cabinets T Ea
15. mal Foreign particles in the gas line may cause an orange flame at first but this will soon disappear SPECIAL NOTE To convert the oven back to natural gas reverse the instructions given in making L P Adjustments Once the conversion is complete and checked ok fill out the LP sticker and include your name organization and the date the conversion was made Apply the sticker near the regulator to alert others in the future that this appliance has been converted to LP gas If converting back to natural gas from LP please remove the sticker so others know the appliance is set to use natural gas ADJUSTING LOW FLAME SETTING ON COOKTOP BURNERS Low setting adjustments must be made with two other burners in operation on a medium setting This procedure prevents the low flame from being set too low resulting in the flame being extinguished when other burners are turned on A Remove the valve control knobs Through the opening locate the valve bypass screw located on the lower right side of the valves Using a small screwdriver screw down the bypass screw fully in a clockwise rotation Printed in the United States
16. ocedures A CHECKING THE OVEN BURNERS To check the bake burner flames with the oven door in the closed position 1 Open the door and remove it 2 Remove the oven racks 3 Remove the oven bottom Lift the oven bottom up at rear and pull forward 4 Remove the four screws holding the burner baffle flame spreader to the burner box 5 Install and close the oven door 6 Turn on the bake burner As you watch the flames check the following e Burner flames should not flutter or blow away from the burner e They should be blue in color with no trace of yellow The broil burner flames may be seen without removing the racks oven bottom or bake baffles ADJUST THE AIR SHUTTER BAKE BURNER 1 Remove the orifice fitting cover 2 Use a screwdriver to loosen the air shutter screw 3 Adjust the air shutter to 11 32 4 Retighten the air shutter screw Orifice fitting Air shutter Su S PIA WHAT ADJUSTMENT TO MAKE a If the flames are yellow open the air shutter more than the original setting b If the flames blow away or fluttered from the burner close the air shutter more than the original setting Burners should be checked frequently BROIL BURNER 1 The broil burner is located and accessible in the top rear of the oven 2 Using a screwdriver loosen the air shutter a adjustment screw AA Make the air s Za shutter Air shutter adjustment adjustment screw Reti
17. r local appliance dealer IMPORTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED An adequate electrical supply and outlet must be used to operate the electrical parts of your range e The power cord of this appliance is equipped with a three prong grounding plug which must be used with a properly grounded three hole outlet with standard 120 Volt 60 cycle AC household current When a standard two prong wall receptacle is encountered it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three prong wall receptacle by a qualified electrician Do not under any circumstances cut or remove grounding prong from the range cord Failure to provide proper ground may create a hazardous condition Installation Instructions GAS CONNECTIONS 11 MAKING THE CONNECTIONS A Install a manual shut off valve in the gas supply line in an easily accessible location Know how and where to shut off the gas supply to the range Shut off gas supply before removing an old range Leave it off until hookup of new range is finished Because solid pipe restricts moving the range we recommend use of a C S A certified flexible metal appliance connector A WARNING never reuse old flexible connectors The use of old flexible connectors can cause gas leaks and personal injury Always use new flexible connectors when installing a gas
18. the trim holding the filler piece centered on the maintop frame and pushing upward to close the gap between the bottom of the cooktop and the filler trim 15 When the trim is set in the proper position tighten the 2 mounting screws The top of the trim should be located below the cooktop edge to prevent pots pans and skillets from damaging the painted parts Refer to the Standard Installation of the Range on page 6 Maintop filler Poe 2 8 screws FOR NON BUILT IN INSTALLATION END OF CABINET LOCATION When installing the range at the end of a cabinet section which will expose the unfinished side of the range use Body Side Kit JXS77XX Refer to the kit instructions for installation details C ISLAND INSTALLATION Attach the Anti Tip bracket per instructions in Step 12 making sure that the rear of the bracket is 25 from the front of the countertop Be aware that the screws provided are long and may penetrate through the back of the island cabinets In this event use shorter screws not provided or the screws provided should be used in the floor see Step 12B for Wood Concrete Floor Installation Do not use Backguard Kit JXS32XX Installation Instructions INSTALL THE RANGE CONT ALTERNATE CONSTRUCTION PREPARATION cont FOR CABINET OPENINGS APPROXIMATELY 30 3 8 If range is installed in cabinet opening approximately 30 3 8 the Vertical Side Trim Kit JXS86XX should be used to cov
19. until the range is within 2 of engaging the anti tip bracket Remove the protective trim from the side of the cooktop if provided Using the adjustable pliers or wrench carefully screw in the back leveling leg until the cooktop overhang comes to rest on the countertop Adjustable wrench or pliers Carefully screw in the front two leveling legs similar to Step E until the cooktop overhang touches the countertop Carefully push the range into the opening until the anti tip bracket engages and the vertical sides are flush with the cabinet Countertop Cabinet 10 13 SLIDE RANGE INTO OPENING cont H Plug the range cord into the receptacle Locate the cord in the back of the range in a manner that it will not touch or be moved by the drawer Position range cord so that there is no interference with storage drawer STORAGE DRAWER AA SS ee A LLELLLLLLLLLLLLL LL LLL LL LLL LLL LLL LLL FINAL CHECK OF ANTI TIP BRACKET When installation is complete and the range is in place check to be sure that the rear leveling leg is fully inserted into the slot of the Anti Tip Bracket C a T Kie Installation Instructions 15 REPLACE THE OVEN DOOR REPLACE THE STORAGE NOTE The oven door is heavy You may need DRAWER help lifting the door high enough to slide it Place the drawer rail on the guides into the hinge slots Do not lift the door by P
20. ush the drawer in until it stops the handle Li ift the front of the drawer and push A Lift the oven door by placing one hand on in until the stops clear the guides each side The door is heavy so you may Lower the front of the drawer and push need help Do not lift the door by the handle in until it eloses SPECIAL INSTRUCTIONS IF YOU ARE HAVING PROBLEMS WHILE REPLACING With the door at the same angle as the THE STORAGE DRAWER removal position halfway between the closed and broil stop position seat the notch of the hinge arm into the bottom Drawer edge of the hinge slot The notch of the Power cord Drawer does front panel hinge arm must be fully seated into the may be otclose Rear drawer a completely support is rom body bottom of the slot obstructing drawer in resting on top this area of guide rail If Drawer Won t Close Hinge arm Bottom edge rail is in the guide If Drawer is Crooked of slot f Si P Remove and replace making sure the power y cord is not obstructing the drawer and or the Hinge notch Rear drawer support is on top of guide rail on Drawer front panel C Fully open the door until it is parallel to the Hane ide r tipped to one side the floor If the door will not fully open the notch in the hinge is not seated correctly in the bottom edge of the slot Repeat steps A and B if necessary D Push the hinge locks up against the front frame of the oven cavity to the locke
Download Pdf Manuals
Related Search