Alpine KTC-222GY Car Monitor
Contents
1. 77 4N_PINE KT C 222GY 50 0388A 002 KTC 222TN 50 0388A 014 FORD EXCURSION Overhead Console for use with Mobile Overhead Monitor INSTALLATION MANUAL These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 Awl or scribe point tool or similar 4 Razor knife or similar tool 5 18 GA wire 4 6 1 8 Drill Bit 7 Rubbing alcohol 8 ALPINE TMX R680A Mobile Overhead Monitor Dec 31 2000 INSTALLATION INSTRUCTION 44 0088A Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION ed To ITEM Description SCREW 6 x 3 8 PPH SCREW 8 X 9 16 PWH SCREW 8 X 1 PWH SCREW 8 32 X 1 1 2 PPH CONVOLUTED TUBE 1 2 LD X 3 VELCRO TAPE 1 X 6 TEMPLATE REAR MOUNTING BRACKET FRONT MOUNTING BRACKET A C BLOCK OFF COVER CONSOLE SWITCH SPDT Q eS SR Se Se SS he UUN me N PEBLeertianewone Dec 31 2000 INSTALLATION INSTRUCTION 44 0088A Printed in the U S A Tea a OE I REMOVAL OF O E2. M EQUIPMENT 1 Remove and retain rear A C control assembly Assembly housing is secured with 2 two spring clips on front of housing Pull down to disengage then slide forward to clear bracket See Photo 1 Disconnect wiring and set assembly in a safe place for re use later 2 Remove and discard center and rear A C vent in PHOTO 1 headliner by rotating outer ring on louver 90 degrees then pulling downward Il PREPARATION OF VEHICLE INTERIOR 3 Using a razor knife carefully trim headliner as shown this will allow clearance for mounting bracket and A C block off cover See Photo 2 Locate template item 7 pg2 between dome lights and rear edge of O E console 02 Make sure that arrow is pointing forward Carefully cut and remove indicated headliner See Photo 2 PHOTO 4 Photo 3 Leave front side of insulation attached 5 Use rubbing alcohol to clean sheet metal in area previously cut Use a clean cloth to dry surface Insert rear mounting bracket item 8 pg 2 into opening and position tab 24 1 8 from rear edge of O E cut out Make sure bracket is centered between roof ribs and firmly press against roof See Photo 4 Position insulation between roof and bracket flange 6 Remove and retain 1 one O E screw in front pocket of O E overhead console Pull down on console to gain access to dome light wiring 7 Construct a 2ft jumper harness that will connect the vehicle s dome liBHQERS to th
3. and cabling per instructions included with LCD monitor 21 Check function of all component and lights See operating instructions for video operations check For further assistance refer to the TMX R680A owner s manual for the technical support phone number listed for your area 23 Raise LCD more Ehki into locked position 24 Cut Velcro tape item 6 pg 2 into 2 pieces Remove protective backing from tape and apply to remote controls Position them against the console door and press firmly on remote while holding the door 25 Raise remote control door into locked position 22 Insert monitor housing into opening in console Note Make sure wires do not get pinched between housing and console Align holes in housing with clips in mounting bracket Secure using 4 four 8 32x 1 1 4 screws item 4 pg 2 See Photo 11 Caution Do not overtighten screws PHOTO 12
4. e lights in LCD monitor housing Refer to wiring connections section 4 of the TMX 680A owner s manual for details 8 Route dome light wire under brace on console and connect O E connector to the O E dome light Route jumper harness through pod opening on console See Photo 5 9 Using a test light test function of lights 10 Install O E console in original manner PHOTO 7 11 Install and route all video and audio cables and any other added component requirements to their respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to C pillar Down the C pillar to the floor Route the power lead to an accessory controlled source Connect the ground lead to the vehicle chassis Route the remaining wiring to the VCP location See Photo 6 Connect per instructions included with the video system 12 Install block off cover item 10 pg 2 and secure using 1 one 8 x 9 16 screw item 2 pg 2 at rear area and 1 one 8 x 1 Screw item 3 pg 2 at front area Do not overtighten screws See Photo 7 PHOTO 5 13 Detach A C wire harness from brace to allow connectors to reach the new A C control location See Photo 8 14 Install mounting bracket item 9 pg 2 by inserting tabs into slots in O E bracket and securing front of bracket using 2 two 8 x 9 16 screws item 2 pg 2 See Phot
5. o 8 15 Install convoluted tube item 5 pg 2 around wire harness to prevent chaffing against bracket See Photo 10 PHOTO 6 lll PREPARATION OF CONSOLE 16 Remove A C control from rear bezel assembly previously removed in step 1 Modify A C control by drilling 3 three 1 8 dia holes in front mounting tabs See Photo 9 17 Place A C control in opening in console item 11 pg 2 Make sure control is centered and secure using 5 five 6 X 3 8 screws item pg 2 See Photo 9 PHOTO 8 IV INSTALLATION OF CONSOLE Caution Use extra support for the console until secured to the vehicle Failure to do so may cause damage to console or installed components 18 Install dome light switch item 12 pg 2 into opening on front of console item 11 pg 2 Raise console into approximate po8H rfl connect A C control wires 6 Insert bracket on rear of console into rear mounting bracket item 8 pg 2 and slide rearward Position console against headliner Make sure console alignment is straight and matches contours in headliner then secure console using 2 two 6 x 3 8 screws item 1 pg 2 through the slots in bracket on console into holes on front mounting bracket See Photo 10 19 Release LCD monitor panel from locked position Lower to viewing position for access to mounting location in top of housing 20 Raise monitor housing into approximate position and connect all wiring to components Connect wiring
Download Pdf Manuals
Related Search