GE JKP86SHSS Electric Double Oven
Contents
1. Remove all items from the inside of the oven Check that conduit is securely connected to the junction box Turn on the power to the oven Refer to your Owner s Manual Verify that the bake and broil units and all cooking functions operate properly Check that the circuit breaker is not tripped nor the house fuse blown See your Owner s Manual for troubleshooting list 11 NOTE TO ELECTRICIAN The power leads supplied with this appliance are UL recognized for connections to larger gauge household wiring The insulation of these leads is rated at temperatures much higher than the temperature rating of household wiring The current carrying capacity of a conductor is governed by the wire gauge and also the temperature rating of the insulation around the wire NOTE ALUMINUM WIRING A WARNING improper CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN RESULT IN AN ELECTRICAL HAZARD OR FIRE Splice copper wires to aluminum wiring using special connectors designed and UL approved for joining copper to aluminum and follow the manufacturer s recommended connector procedure closely NOTE Wire used location and enclosure of splices etc must conform to good wiring practice and local codes NOTES 122. Electrical Connections cont New Construction and Four Conductor Branch Circuit Connection e When installing in new construction or e When installing in a mobile home or e When installing in a recreational vehicle or e When local codes do not permit grounding through neutral a Cut the neutral white lead from the crimp Re strip the neutral white lead to expose the proper length of conductor Ground Junction Box Cover Attach the appliance grounding lead green or bare copper in accordance with local codes If the residence grounding conductor is aluminum see WARNING on page 6 Connect the oven neutral white lead to the branch circuit neutral white or gray in accordance with local codes using a wire nut Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with local codes using wire nuts If the residence red black or white leads are aluminum conductors see WARNING on page 6 Install Junction Box Cover Three Conductor Branch Circuit Connection When connecting to a three conductor branch circuit if local codes permit a Connect the bare oven ground conductor with the crimped neutral white lead to the branch circuit neutral white or gray in color using a wire nut Ground and Neutral Wires Junction Box Cover Connect the oven red lead to the branch circuit red lead in accordance with local
3. bend the bottom trim The bottom trim provides an opening for cooling air to enter the cabinet This opening should never be blocked Installation Instructions D Replacing the Oven Door D3 Open the oven door as far as it will open NOTE The oven door is heavy You may need help lifting the door high enough to slide it into the hinge slots D4 Push the hinge locks up against the Do not lift the door by the handle front frame of the oven cavity to the locked position D1 Lift the oven door by Locked P sition placing one hand on each side The door is heavy SO you may need help Do not lift the door by the handle Securely Fitted into Bottom of Hinge Slot Close the oven door D2 With the door at the same angle as the removal position half way between the closed and broil stop position seat the notch of the hinge arm into the bottom edge of the hinge slot The notch of the hinge arm must be fully seated into the bottom of the slot Hinge Arm Bottom Edge of Slot Hinge Notch 10 iW Pre Test Checklist lt 8 RRR Ss Installation Instructions Remove all protective film if present and any stickers Check to be sure that all wiring is secure and not pinched or in contact with moving parts Check that the bottom trim is installed properly see page 9 Check to be sure the mounting screws are installed and flush with the side trim see page 8 Operation Checklist
4. codes using a wire nut Connect the oven black lead to the branch circuit black lead in accordance with local codes using a wire nut If the residence red black or white leads are aluminum conductors see WARNING on page 6 Install Junction Box Cover Installation Instructions Securing the Oven in the Opening Sliding the Oven Into the Drilling the Pilot Holes and Opening Mounting the Oven a Loop do not tie a 36 string around the conduit before the oven is slid into place NOTE Before drilling the pilot holes This will keep the conduit from falling make sure the oven is pushed as far behind the oven back into the opening as it will go and centered a Drill through the mounting holes top and bottom of the side trim for the 8 screws provided Pull out on string loop while pushing the oven into the cabinet The screws must Beant Hole be a minimum of ocations 1 4 from the front of the cutout b Lift oven into cabinet cutout using the oven T WARNING Mounting opening as a grip Carefully push against oven front frame Do not push against do so could result in the oven outside edges falling out of the cabinet causing c As you slide the oven back pull the string serious injury so that the conduit will lie on top of the oven in a natural loop screws must be used Failure to i b Secure the oven
5. four conductor connection to an electric oven When installing an electric oven in new construction a mobile home recreational vehicle or an area where local codes prohibit grounding through the neutral conductor follow the instructions in the section on NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION You must use a three wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If you connect to aluminum wiring properly installed connectors approved for use with aluminum wiring must be used Installation Instructions Remove packaging materials Check inside microwave behind hinges and under false bottom Remove labels on the outside of the door plastic on trims and panel and all tape around oven Broiler Pan Literature and Grid Pack Open oven door and remove literature pack broiler pan and grid and oven racks Open microwave door and remove shelves and turntable package Remove Installation Instructions from literature pack and read them carefully before you begin Be sure to place all literature Owner s Manual Installations etc in a safe place for future reference YW Pre Installation Checklist Door removal is not a requirement for installation of the product but is an added convenience To remove the door VS Open the oven door as far as it will go Push both hinge nmgr j locks down toward R Boe iion the
6. Installation 27 Built In Wall Oven with Microwave Instructions IKP86 If you have questions call 1 800 GE CARES or visit our website at www GEAppliances com Before You Begin e Proper installation is the responsibility of the installer and product failure due Read these instructions carefully and completely to improper installation is NOT covered IM PO RTANT save these underwarranty instructions for local inspector s use NOTE This appliance must be properly grounded Sait is carol ATTENTION INSTALLER e Note to Installer Be sure to leave these All electric wall ovens must be hard wired instructions with the consumer direct wired into an approved junction Note to Consumer Keep these box A plug and receptacle is NOT permitted instructions for future reference on these products Parts Included Materials Needed 2 7 g O Wire Nuts Screws For Installation Metal Bottom Trim Strain Relief Clamp Junction for 1 2 conduit Box S Tools Needed id Sting Ate 1 8 Drill Bit and Phillips Electric or Hand Drill Screwdriver 229C4053P507 3 31 10526 3 06 03 JR Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety e Be sure your oven is installed properly by a qualified installer or service technician e Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure Weight on the oven door could cause the oven to tip and result in in
7. door frame Hing PNN to the unlocked Slot SS position This may z y require a flat blade screwdriver Place hands on both sides of the door and close the oven door to the removal position This is half way between the broil stop and fully closed Lift door up and out until the hinge arms clear the slots Hinge Clears Slot NOTE The oven door is very heavy Be sure you have a firm grip before lifting the oven door off the hinges Use caution once the door is removed Do not lay the door on its handle This could cause dents or scratches Continued on following page Installation Instructions iY Pre Installation Checklist con VS Place the oven on a table or platform VS Remove the bottom trim from the top even with the cutout opening of the oven It will be installed at the Platform must support 255 Ibs end of the installation process The trim is wrapped separately and taped to the top of the unit Installation Instructions A Cutout for Built In Oven with Microwave Junction Box Cabinet Width Cabinet Location 10 iE t i Recommended Minimum Cutout Cutout Location Allow 7 8 for Width from Floor 21 5 8 overlap of oven 25 Min over side edges 25 1 4 Ma of cutout amen a Cutout Depth 23 1 2 equivalent Cutout Cutout Width 25 Min runners Height 44 25 1 4 Max level with 41 1 8 Min Above bottom 41 1 4 Max pase rail of cutout Cutout H
8. eight 41 1 8 Min ini 1 Alternate Allow a minimum of 20 for clearance to adjacent Junction Box 41 1 4 Max corners drawers walls etc when door is open NOTE If the cabinet does not have a front frame and the sides are less than 3 4 thick shim both sides equally to establish the cutout width Recommended minimum cutout location Allow mihimum from floor 21 5 8 1 for overlap 2 x 4 or equivalent of oven top and runners level with bottom of cutout bottom of cutout If the cabinet does not have a solid bottom two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven The runners and braces must support 255 Ibs NOTE If marks blemishes or the cutout opening are visible above the installed oven it may be necessary to NOTE If using equivalent add wood shims under the runners and runners then the center of the front trim until the marks or opening equivalent runners should be are covered 20 1 2 Installation Instructions Electrical Connections ATTENTION INSTALLER B1 Turn off the circuit breaker or remove fuses to the oven branch circuit All electric wall ovens must be hard wired B2 With the oven supported on a table or direct wired into an approved junction platform in front of the cabinet opening box A plug and receptacle is NOT permitted connect the flexible condu
9. it to the on these products electrical junction box as shown below DO NOT shorten the flexible conduit Position the conduit in such a manner The conduit strain relief clamp must be that it will lie on top of the oven in securely attached to the junction box a natural loop when the oven is and the flexible conduit must be securely installed You will need to purchase attached to the clamp If the flexible an appropriate strain relief clamp to _ conduit will not fit within the clamp do not complete the connection of the conduit install the oven until a clamp of the proper to the junction box size is obtained NOTE TO ELECTRICIAN The 3 power leads supplied with this appliance are i Peed Box UL recognized for connection to heavier gauge household wiring The insulation of these 3 leads is rated at temperatures much higher than the temperature rating of household wiring The current carrying capacity of the conductor is governed by the wire gauge and the temperature rating of the insulation around the wire WARNING Improper connection of aluminum house Strain Relief Clamp wiring to copper leads can not included must be used at result in an electrical hazard or fire J nction Box Use only connectors designed for Pisce ver Sna joining copper to aluminum and follow support to assist in the manufacturer s recommended ai procedure closely UW Continued on following page Installation Instructions
10. jury Never allow anyone to climb sit stand or hang on the oven door e Make sure the cabinets and wall coverings around the oven can withstand the temperatures up to 200 F generated by the oven j WARNING The electrical power to the oven supply line must be shut off while line connections are being made Failure to do so could result in serious injury or death Electrical Requirements This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as noted on rating plate Rating plate is located on the inside wall of the microwave oven We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician After installation have the electrician show you where your main oven disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your oven according to governing codes could result in a hazardous condition If there are no local codes your oven must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 70 Latest Edition You can get a copy by writing National Fire Protection Association Batterymarch Park Quincy MA 02269 Effective January 1 1996 the National Electrical Code requires that new but not existing construction utilize a
11. to cabinet with screws d When you are sure the conduit is out of the provided way slide the oven 3 4 way back into the ee opening Remove the string by pulling on NOTE If the cabinet is particle board you one end of the loop must use 8 x 3 4 particle board screws These may be purchased at any hardware store Continued on following page Installation Instructions Preparing for the Bottom a Using the trim Remove the trim Trim Installation With oven installed take the bottom trim and center it on the bottom front edge of the cabinet opening With Lower Trim in Position Mark 3 Mounting Hole Locations LL as a template mark the center of each slot three total where the mounting holes will be drilled Remove Lower Trim Before Pre drilling Mounting Drill pilot holes into the Holes center of each template mark Installing the Bottom Trim a Place the bottom metal trim centered over the pre drilled mounting holes Tape the edges of the trim down to maintain the alignment ue Side Trim Side Trim Using three trim screws provided secure the bottom trim to the bottom edge of the cabinet IMPORTANT If this unit is ever removed from the cabinet or the oven is ever pulled out for service the trim must be removed first or damage to the trim will occur A CAUTION Be sure you do not tip the oven forward during installation or you may
Download Pdf Manuals
Related Search