GE JEB1095SB Oven
Contents
1. Installation Instructions Built In Microwave Convection and Microwave Ovens Models ZMC1095 JEB1095 JEB1055 Important Safety Information Contents Before you begin Read these instructions completely and carefully IMPORTANT Save these instructions for local inspector s use IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES NOTE TO INSTALLER Be sure to leave these instructions with the consumer NOTE TO CONSUMER Keep these instructions with your Use and Care Book for future reference If you have questions concerning the installa tion of this product call the GE Answer Center Consumer Information Service at 800 626 2000 24 hours a day 7 days a week If you received a damaged oven you should contact your dealer Safety Instructions This product requires a three prong grounded receptacle The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded If not properly grounded or if the outlet box does not meet the electrical requirements noted under ELECTRICAL REQUIREMENTS a qualified electrician should be employed to correct any deficiencies CAUTION For personal safety remove house fuse or oven circuit breaker before beginning installation to avoid severe or fatal shock injury CAUTION For personal safety the mounting surface must be capable of supporting the cabinet load in add2. JECT TO CHANGE WITHOUT NOTICE DWG NO 164D3333P205 N D 322 5 99 Printed in Korea
3. ces of the cabinet should be finished to match the cabinet surface eIn both a recessed and shadow box installation the floor of the cutout must be level and even with the bottom edge of the cutout Use runners inside the opening to raise the floor to matching height a Top Rail 2 gt Sy Bottom Rail Shadow Box Installation e Cut top and bottom rail to fit the width of the opening Cut the height of the rails to fit the cutout height Use cleats to secure the rails to the inside walls of the cabinets Parts supplied e 2 mounting screws e 4 extra side trim screws e 2 side trim pieces Design Information Built In Microwave Convection Oven e Open the door e Remove the two 2 retainer screws from the Step bottom side of the grille one at each side Remove Grille Retainer Screw Retainer Screws WARNING Remove Side Trim Before Removing Oven Do Not Lift Oven With Side Trim e Roll the grille forward from the bottom Disengage the locating tabs and remove the grille from the unit Note Grille appearance varies depending on model If you are installing in a 27 opening skip this Step step and discard the optional side trim For a 30 installation appearance Install Side e Slide one side of the oven out of the opening A ji about 4 to 5 leaving the opposite side Trim for 30 against the cabinet T
4. he oven should be at Appearance RAGE Lok CAUTION LIFT THE OVEN FROM THE BOTTOM DO NOT Il i he si i allow easier access to t e side trim screws LIFT THE OVEN WITH THE SIDE TRIM e Remove the two side trim screws SKIP THIS STEP z Side trim will not support the weight of the oven e Hold a side trim piece against the oven with 3 IF YOU ARE NOT es e Remove the two side trim screws and install screw holes aligned Reinstall original screws DN ee Rai i the opposite side trim piece Note 4 extra side trim screws are provided for your convenience i e Carefully lift the oven by the bottom and e Lift the oven by the bottom pull out and f i ted slide straight back into the opening Check turn the oven to expose the opposite side to be sure power cord is not trapped beneath the oven USING THE OPTIONAL SIDE TRIM e Using the installation holes as a guide drill Step two 2 pilot holes 1 8 diameter into the P cabinet e nstall the two 2 installation screws Drive Installation CAUTION Place tape or A Screws cardboard over trim edges to ze Installation prevent damage while drilling Screw pilot holes Hole Installation Built In Microwave Convection Oven e Reinstall the grille with the two retainer SCTEWS Step Reinstall Grille Notes Buili In Microwave Convection Oven Pub No 49 8978 SPECIFICATIONS SUB
5. ition to the added weight of this 70 pound product plus additional oven loads of up to 50 pounds or a total weight of 120 pounds CAUTION For personal safety this product cannot be installed in cabinet arrangements such as an island a peninsula or below a countertop Design Information Product Dimensions aaa saa aaaa aaa aaa zazna nata annnia Cutout Dimensions Electrical Locations eeeouo aaa Advance Planning essessanes asa oa aaa aa e znana szans zaezaaaeznaza Installation Installation Option se seann aaa aaa aaa aaeaa Tools and Materials Required c ccssesessesssesseseseeseeeseeses Parts Supplied 21 11 11 22 111 111 Step 1 Slide Microwave into the Cutout Step 2 Remove Grille Retainer Screws Step 3 Install Side Trim for 30 Appearance Step 4 Drive Installation Screws Step 5 Reinstall Grille Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty See the Use amp Care Guide for warranty information Electrical Requirements Product rating is 120 volts AG 60 Hertz 13 amps and 1 45 kilowatts This product must be connected to a supply circuit of the proper voltage and frequency Wire size must con form to the requirements of the National Electric Code or the prevailing local code for this kilowat
6. n discard the side e Side trim pieces are provided for installation trim pieces into a 30 wide space For a matching e Cutout dimensions are the same for both 27 appearance use the side trim when installing or 30 wide cabinet installations the microwave oven above a 30 single wall oven Installation Options Step Slide the Microwave into Cutout Installation These built in ovens can be inset into the cabinetry In this installation the microwave is recessed and flush with the front surface of the cabinet A shadow box affect can be achieved by installing a rail at the top and bottom of the microwave to fill the cutout height In this ENT 26 3 4 13 16 x 13 16 Sq Stopper Strip 4 sides Inset Recessed Installation e Cut 4 stopper strips 13 16 square to frame the opening install the strips 13 16 from the front edge of the opening Oven overlap will cover all 4 stopper strips Tools and Materials required 2 Phillips screwdriver e Hand held drill motor e High speed drill bit 1 8 diameter e 2 each 8x1 Round head wood screws e 3 8 slothead screwdriver e Lift and hold the oven up to the opening Hold the oven at the 45 angle and plug in the power cord e Carefully slide the oven into the cabinet Check to be sure that power cord is not trapped under the bottom or the sides of the oven Built In Microwave Convection Oven installation exposed inside surfa
7. t rating The power supply cord and plug should be brought to a separate 15 or 20 ampere branch circuit single grounded receptacle The outlet box should be located near the cord entry point The outlet box and supply circuit should be installed by a quali fied electrician and conform in the National Electric Code or the prevailing local code Usage Can be installed over any GE single electric built in oven DOUBS BP R Product Dimensions Cutout Dimensions Electrical Location Advance Planning Design Information Built In Microwave Convection Oven Models ZMC1095 JEB1095 JEB1055 Available in White Black and Stainless Steel 29 3 4 With Optional Side Trim 6 3 8 26 3 4 53 8 f f 18 5 8 L L 13 16 u pu u 27 or 30 2A Construct Base ZANE Min 3 8 Plywood ia Supported by in s ong 2X40r1x2 20 1 4 f for Flush h 25 1 4 t 17 Min Runners all Outlet o gt Four Sides LJ is 9u 1 2 17 1 2 17 1 2 Leao LL JE 1 7 8 Min TI Construct Base ii Per Oven Min 3 8 Plywood Requirement Supported by 2x4or1x2 a Runners all J Four Sides 45 1 4 Locate outlet box in the shaded area These microwave ovens are sized to fit a 27 e If you are installing into a 27 wide cabinet wide cabinet or over a 27 wide wall ove
Download Pdf Manuals
Related Search